Mini Stereo Audio Amplifier using IC TEA2025

This is a very simple schematic diagram of mini stereo audio amplifier build based the main power IC of TEA2025. This IC support both single audio channel and stereo audia channel. There will be 2x2.5W for stereo channel and 5W for mono channel with bridge mode. TEA2025 is a monolithic integrated audio amplifier in a 16-pin plastic dual in line package. It is designed for portable cassette players and radios, featured with Working Voltage down to 3V, Few External components, High Channel isolation, Voltage gain up to 45dB(Adjustable with external resistor), Soft clipping and Internal Thermal protection.

Read More

2 x 15W Stereo Audio Amplifier with TDA4935

This is the scheme diagram of 2 x 15W stereo audio amplifier using single power IC TDA4935. The amplifier is a Class B stereo and is designed with the TDA4935 from Siemens, which delivers 15 watts each channel. It can also be configured in BTL or bridge, thus delivering 30 watts in mono channel configuration.

Read More

5W Audio Amplifier based LA4460

This is the scheme diagram of 5W audio power amplifier which can be built for general purpose and can drive speakers approximately 8 to 12 inches. This 5W audio amplifier circuit is based on the Sanyo LA4460 IC.  Based on the IC datasheet, the LA4460 has capability to drive up to 12W power output, of course you will need more power in your power supply.

Read More

Notebook / Netbook Audio Amplifier

The audio output from a standart notebook or netbook with built-in speakers is low and the quality is also low. Alternatively, you can use a earphones to make good quality audio output, but for some people, earphones is unconfortable for them.

A power amplifier is needed to achieve a high volume. The following diagram is a simple circuit to amplify the notebook’s audio output.

The circuit is very simple and inexpensive, it use power amplifier IC LA4440 (IC1) and a few other components. LA4440 is a dual channel audio power amplifier, so you just need an IC for stereo application. It has low distortion over a wide range of low to high frequencies with good channel separation. Inbuilt dual channels enable it for stereo and bridge amplifier applications.

Read More

50W Amplifier Kit Project based TDA1514A

Here the very simple but powerful amplifier kit which built based on TDA1514A amplifier chip. The circuit is for single channel only, you should build two similar circuit for stereo application. A heatsink is a must to be attached on the IC TDA1514A. This circuit can be used as well as stereo amplifiers Bass in a 5.1 system.

Read More

2x2W Stereo Audio Amplifier based LM1877

Here the 2x2 stereo audio amplifier based on single chip LM1877. LM1877 is an amplifier chip designed to deliver 2W/channel continuous into 8Ω loads. This is a very simple and easy build low power audio amplifier with a low number of external components, and still provide flexibility for use in stereo phonographs, tape recorders and AM-FM stereo receivers, etc.

Read More

LM380 Audio Amplifier Circuits

This is an easy made, really simple and low cost mini audio amplifier based on integrated circuit LM380. Of course the main part of this amplifier is LM380 itself. This LM380 audio amplifier is simple and easy to built because of the simple circuit design which use minimal external components.

The the above amplifier circuit shows the LM380 in non-inverting mode, with the inverting input left open (the inverting input may also be tied to ground, either directly or through a resistor or capacitor). C2 is used to decouple Vcc from ground. The optional RC circuit at the output (pin 8) is used for added stability, for example, to remove/reduce oscillations in an RF-sensitive application.

Read More

150W Car Amplifier based LA47536

Here the 150W car amplifier circuit, build based LA47536 power IC. The LF353 which is manufactured by National Semiconductor, will split audio signal into three bands. While, the power IC LA47536 of SANYO will boost these signals. In stereo mode, we shall have the action of eight high speakers who are going to create a very important sound pressure.

Read More

32W HiFi Audio Amplifier Circuit based TDA2050

This is the very simple and easy build schematic diagram of 32W HiFi audio amplifier circuit based single power chip TDA2050. The TDA2050 can be work with single power supply or split power supply, but on the above circuit design, it use split power supply to work. A TDA2050 must be mounted on the heatsink to prevent overheat and keep good performance.

Read More

4W Audio Amplifier based TDA1013B

This is the scheme diagram of 4W audio amplifier built based single power chip TDA1013B. This is a mono amplifier circuit, so you need to build two similar circuit to make it stereo. 18V DC power supply with at least 0.5A current is recommended for this circuit.

Read More

2x11W Stereo Audio Amplifier with LM4755

Here the circuit diagram of 2x11W stereo audio amplifier build based on single power chip LM4755 manufactured by National Semiconductor.

The LM4755 is a stereo audio amplifier able to deliver 11W per channel of constant typical output power to a 4Ω load or 7W per channel into 8Ω applying a single 24V supply at 10% THD+N. The internal mute circuit and pre-set gain resistors present for a very economical design solution.

Read More

2x30W Stereo Audio Amplifier based STK465

This is the stereo audio amplifier circuit build based on well-known power chip of STK465. The STK465 has two power amplifier module, so, with single chip of STK465 you can build a stereo amplifier with two input channels and two output channels. This circuit is require split power supply, recommended supply : +/- 28V / 2A. The STK465 should be mounted on proper heatsink.

Schematic diagram:

Component Part list:

R1 = 1K C1 = 1uF/35V R2 = 3,3K C2 = 470pF R3 = 100 C3 = 100uF/60V R4 = 330 C4 = 100uF/60V R5 = 3,3K C5 = 10uF/60V R6 = 1K C6 = 47uF/60V

R7 = 0,33 C7 = 8,2pF R8 = 33k C8 = 0,1uF R9 = 4,7 C9 = 1uF/35V R10 = 1k C10 = 470pF R11 = 3,3k C11 = 100uF/60V R12 = 100 C12 = 100uF/60V

R13 = 330 C13 = 10uF/60V R14 = 3,3k C14 = 47uF/60V R15 = 1k C15 = 8,2pF R16 = 0,33 C16 = 0,1uF R17 = 33k R18 = 4,7 IC1 = STK465 LS1 = Speaker 40W 8 or 4 Ohm

Read More

Stereo Power Amplifier 120W based STK4241V

This is the circuit diagram of stereo power amplifier which use STK4241V as the main component. The amplifier will give you audio power output up to 120W on each channel if you use optimum power supply.

STK4241V features:

• Muting circuit built-in to isolate all types of shock noise
• Current mirror circuit for low 0.08% total harmonic distortion

Read More

3W Class D Audio Amplifier with LM48511

This is the 3W Class-D audio amplifier circuit build using power IC LM48511 manufactured by National Semiconductor. The circuit is very simple with a few external components. The 3W Class D amplifier features a low noise PWM architecture that eliminates the output filter, reducing external component count, board area consumption, system cost, and simplifying design. A selectable spread spectrum modulation scheme suppresses RF emissions, further minimize the requirement for output filters.

Read More

TDA7294 : 60W Power Audio Amplifier Circuit

This is the circuit diagram of 60W power audio amplifier based TDA7294. The above diagram is for single/mono amplifier only. You can build the stereo amplifier by build two similar circuit. Of course you will need to doubling the power supply too.

Read More

15W OTL Power Amplifier based TDA2030

The following diagram is the circuit diagram of 15W OTL power amplifier which is build based single amplifier chip TDA2030 produced by STMicroelectronics. This circuit is very simple, the main active component was the TDA2030 while the others discrete components supposed to support the TDA2030 to work properly.

15W OTL Power Amplifier Schematic Diagram:

Read More

20W Stereo Power Amplifier Circuit based TDA2005

This is the stereo power amplifier circuit powered using amplifier chip TDA2005. It is required 2 pieces of TDA2005. Each channel build based bridge amplifier circuit, the loudspeaker terminal should not connected to ground.

Read More

200W Power Amplifier Circuit

This is the circuit diagram of 200W power amplifier with high quality audio output. This is a bridge amplifier based power IC TDA2030 and power transistor BD708/BD708 KT818/KT819.

Schematic diagram:

Read More

TDA2822 1W Stereo Headphone Amplifier Circuit

Read More

30W Bridge Amplifier Circuit based TDA2040

This is the schematic diagram of 30W bridge amplifier circuit based on class AB audio amplifier chip TDA2040.

Read More