Product data sheet

Characteristics

ATV71HC11N4

variable speed drive ATV71 - 110KW 150HP 480V - EMC filter

Product availability: Stock - Normally stocked in distribution facility

Price*: 12652.30 USD

Feb 6, 2015

Commercial Status

Commercialised

Range of product

Altivar 71

Product or component
type

Variable speed drive

Product specific
application

Complex, high-power machines

Component name

ATV71

Motor power kW

110 kW at 380...480 V 3 phases

Motor power hp

150 hp at 380...480 V 3 phases

Motor cable length

<= 200 m unshielded cable

<= 100 m shielded cable

[Us] rated supply

voltage

380...480 V (- 15...10 %)

Network number of
phases

3 phases

Line current

202 A for 380 V 3 phases 110 kW / 150 hp

163 A for 480 V 3 phases 110 kW / 150 hp

EMC filter

Integrated

Assembly style

With heat sink

Variant

Reinforced version

Apparent power

133 kVA at 380 V 3 phases 110 kW / 150 hp

Prospective line Isc

<= 35 kA, 3 phases

Nominal output current

215 A at 2.5 kHz 460 V 3 phases 110 kW / 150 hp

215 A at 2.5 kHz 380 V 3 phases 110 kW / 150 hp

Maximum transient
current

355 A for 2 s 3 phases 110 kW / 150 hp

323 A for 60 s 3 phases 110 kW / 150 hp

Speed drive output

frequency

0.1...500 Hz

Nominal switching
frequency

2.5 kHz

Switching frequency

2.5...8 kHz with derating factor

2.5...8 kHz adjustable

Asynchronous motor
control profile

ENA (Energy adaptation) system for unbalanced loads

Flux vector control (FVC) with sensor (current vector)
Sensorless flux vector control (SFVC) (voltage or current
vector)
Voltage/Frequency ratio (2 or 5 points)

Type of polarization

No impedance for Modbus

The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein. *Prices are indicative

Main

Complementary
Product destination

Asynchronous motors
Synchronous motors

Supply voltage limits

323...528 V

Supply frequency

50...60 Hz (- 5...5 %)

Network frequency limits

47.5...63 Hz

Speed range

1...50 for synchronous motor in open-loop mode, without speed feedback

1...1000 for asynchronous motor in closed-loop mode with encoder feedback
1...100 for asynchronous motor in open-loop mode, without speed feedback

Speed accuracy

+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback
+/- 0.01 % of nominal speed for 0.2 Tn to Tn torque variation in closed-loop mode with
encoder feedback

Torque accuracy

+/- 5 % in closed-loop mode with encoder feedback

+/- 15 % in open-loop mode, without speed feedback

Transient overtorque

220 % of nominal motor torque +/- 10 % for 2 s

170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes

Braking torque

30 % without braking resistor

< 150 % with braking or hoist resistor

Synchronous motor control profile

Vector control without speed feedback

Regulation loop

Adjustable PI regulator

Motor slip compensation

Adjustable
Automatic whatever the load
Not available in voltage/frequency ratio (2 or 5 points)
Suppressable

Local signalling

1 LED red presence of drive voltage

Output voltage

<= power supply voltage

Insulation

Electrical between power and control

Type of cable

Without mounting kit: 1-strand IEC cable at 113 F (45 C), copper 90 C XLPE/EPR
Without mounting kit: 1-strand IEC cable at 113 F (45 C), copper 70 C PVC
With an IP21 or an IP31 kit: 3-strand IEC cable at 104 F (40 C), copper 70 C PVC
With a NEMA Type1 kit: 3-strand UL 508 cable at 104 F (40 C), copper 75 C PVC

Electrical connection

PC/-, PO, PA/+ terminal 2 x 150 mm

PA, PB terminal 60 mm
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 terminal 2 x 100 mm
AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5 mm /
AWG 14

Tightening torque

PC/-, PO, PA/+ 362.83 lbf.in (41 N.m) / 360 lb.in

PA, PB 106.19 lbf.in (12 N.m) / 106 lb.in
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 212.39 lbf.in (24 N.m) / 212 lb.in
AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 5.31 lbf.in (0.6 N.m)

Supply

Internal supply, 24 V DC, voltage limits 21...27 V, <= 200 mA for overload and shortcircuit protection
Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 %, <= 10
mA for overload and short-circuit protection

Analogue input number

Analogue input type

AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max, impedance

30000 Ohm, resolution 11 bits
AI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11 bits
AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution
11 bits + sign

Sampling duration

LI6 (if configured as logic input) 2 ms, +/- 0.5 ms for discrete input(s)
LI1...LI5 2 ms, +/- 0.5 ms for discrete input(s)
Al2 2 ms, +/- 0.5 ms for analog input(s)
AI1-/Al1+ 2 ms, +/- 0.5 ms for analog input(s)

Response time

R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s)

R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)
AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)
<= 100 ms in STO (Safe Torque Off)

Accuracy

AO1 +/- 1 % for a temperature variation 60 C

AI2 +/- 0.6 % for a temperature variation 60 C
AI1-/Al1+ +/- 0.6 % for a temperature variation 60 C

Linearity error

AO1 +/- 0.2 %

AI1-/Al1+, AI2 +/- 0.15 % of maximum value

Analogue output number

Analogue output type

AO1 software-configurable voltage 0...10 V DC, impedance 470 Ohm, resolution 10

bits
AO1 software-configurable current 0...20 mA, impedance 500 Ohm, resolution 10 bits
AO1 software-configurable logic output 10 V <= 20 mA

Discrete output number

Discrete output type

R2A, R2B configurable relay logic NO, electrical durability 100000 cycles
R1A, R1B, R1C configurable relay logic NO/NC, electrical durability 100000 cycles

Minimum switching current

Configurable relay logic 3 mA at 24 V DC

Maximum switching current

R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1,

R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1,
R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4,
R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4,

Discrete input number

Discrete input type

PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to ISO 13849-1 level d
LI6: switch-configurable PTC probe 0...6, impedance: 1500 Ohm
LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm
LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm

Discrete input logic

LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V (state 0)
LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V (state 0)
LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 0)
LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 0)

Acceleration and deceleration ramps

Automatic adaptation of ramp if braking capacity exceeded, by using resistor

Linear adjustable separately from 0.01 to 9000 s
S, U or customized

Braking to standstill

By DC injection

Protection type

Motor thermal protection

Motor power removal
Motor motor phase break
Drive thermal protection
Drive short-circuit between motor phases
Drive overvoltages on the DC bus
Drive overheating protection
Drive overcurrent between output phases and earth
Drive line supply undervoltage
Drive line supply overvoltage
Drive input phase breaks
Drive break on the control circuit
Drive against input phase loss
Drive against exceeding limit speed

Insulation resistance

> 1 mOhm at 500 V DC for 1 minute to earth

Frequency resolution

Display unit 0.1 Hz

Analog input 0.024/50 Hz

Communication port protocol

CANopen
Modbus

Type of connector

Male SUB-D 9 on RJ45 for CANopen

1 RJ45 for Modbus on terminal
1 RJ45 for Modbus on front face

Physical interface

2-wire RS 485 for Modbus

Transmission frame

RTU for Modbus

Transmission rate

9600 bps, 19200 bps for Modbus on front face

4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen

Data format

8 bits, odd even or no configurable parity for Modbus on terminal

8 bits, 1 stop, even parity for Modbus on front face

Number of addresses

1...247 for Modbus

1...127 for CANopen

Method of access

Slave for CANopen

Marking

CE

Operating position

Vertical +/- 10 degree

Height

40.24 in (1022 mm)

Depth

14.84 in (377 mm)

3

Width

14.17 in (360 mm)

Product weight

163.14 lb(US) (74 kg)

Option card

Profibus DP V1 communication card

Profibus DP communication card
Overhead crane card
Modbus/Uni-Telway communication card
Modbus TCP communication card
Modbus Plus communication card
Interface card for encoder
Interbus-S communication card
I/O extension card
Fipio communication card
Ethernet/IP communication card
DeviceNet communication card
Controller inside programmable card
CC-Link communication card

Environment
Noise level

69.5 dB conforming to 86/188/EEC

Dielectric strength

5092 V DC between control and power terminals

3535 V DC between earth and power terminals

Electromagnetic compatibility

Voltage dips and interruptions immunity test conforming to IEC 61000-4-11

Radiated radio-frequency electromagnetic field immunity test conforming to IEC
61000-4-3 level 3
Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3
Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4
Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3
1.2/50 s - 8/20 s surge immunity test conforming to IEC 61000-4-5 level 3

Standards

EN 55011 class A group 2

EN 61800-3 environments 1 category C3
EN 61800-3 environments 2 category C3
EN/IEC 61800-3
EN/IEC 61800-5-1
IEC 60721-3-3 class 3C2
UL Type 1

Product certifications

CSA
C-Tick
GOST
NOM 117
UL

Pollution degree

3 conforming to UL 840
2 conforming to EN/IEC 61800-5-1

IP degree of protection

IP54 on lower part conforming to EN/IEC 61800-5-1

IP54 on lower part conforming to EN/IEC 60529
IP41 on upper part conforming to EN/IEC 61800-5-1
IP41 on upper part conforming to EN/IEC 60529
IP30 on the front panel conforming to EN/IEC 61800-5-1
IP30 on the front panel conforming to EN/IEC 60529
IP30 on side parts conforming to EN/IEC 61800-5-1
IP30 on side parts conforming to EN/IEC 60529
IP00 conforming to EN/IEC 61800-5-1
IP00 conforming to EN/IEC 60529

Vibration resistance

1.5 mm peak to peak (f = 3...10 Hz) conforming to EN/IEC 60068-2-6

0.6 gn (f = 10...200 Hz) conforming to EN/IEC 60068-2-6

Shock resistance

7 gn for 11 ms conforming to EN/IEC 60068-2-27

Relative humidity

5...95 % without dripping water conforming to IEC 60068-2-3

5...95 % without condensation conforming to IEC 60068-2-3

Ambient air temperature for operation

14...122 F (-10...50 C) without derating

Ambient air temperature for storage

-13...158 F (-25...70 C)

Operating altitude

3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m

<= 3280.84 ft (1000 m) without derating

Ordering and shipping details

Category

22132 - ATV71 460V 25 THRU 100HP DRIVES

Discount Schedule

CP4C

GTIN

00785901446224

Nbr. of units in pkg.

Package weight(Lbs)

217.80

Product availability

Stock - Normally stocked in distribution facility

Returnability

Country of origin

CN

Offer Sustainability
Sustainable offer status
RoHS
REACh

Green Premium product

Compliant - since 1002 -

Schneider Electric declaration of conformity

Reference contains SVHC above the threshold -

Product environmental profile

Available

Download Product Environmental

Product end of life instructions

Available

Download End Of Life Manual

go to CaP for more details

Contractual warranty
Period

18 months