wear parts catalog
Doc. no. R 223.1327
SANDVIK CH420:01
This document is valid for:
Serial no. / Machine no.
Sign.
SANDVIK CH420:01
Copyright 2007 Sandvik SRP AB.
All rights reserved. No parts of this document may be reproduced or copied in any form or by
any means without written permission from Sandvik SRP AB. All data and information in this
manual may be changed without further notice. Reservations for misprints.
Document number: R 223.1327
Issue: 20071108
Version: 1
Sandvik
Stationsplan, SE-233 81 Svedala, Sweden
Tel: +46 (0)40 409000, Fax: +46 (0)40 409260
www.sandvik.com
WPC Sandvik CH420:01
General
Ordering information
When ordering parts, always state the machine type, manufacturing number,
serial number and order number according to the identification plate on the
cone crusher or tank. State quantity, article number and denomination for
each ordered part. The quantities listed in this catalog show how many pieces
of each part that are usually exchanged in a certain position.
Crushers identification plate
The figure below shows an example of the crushers identification plate. The
identification plate contains data needed when contacting Sandvik
concerning wear parts.
Please enter the serial number of the associated machine in the intended field
on the first page of this wear part catalog (the copyright page).
Identification plate:
1 Machine type
2 Part number
3 Serial number
4 Order number
1 2
The Type number is a designation system that describes the product.
Type:
1 Type and size of crusher
2 Crushing chamber (concave ring)
3 Mantle
4 Filler ring
5 Eccentric throw (mm)
6 Mark number
2007 Sandvik SRP AB
CH420-F/B/C-25/28/22:1
1
2
3
Doc. no. R 223.1327 Ver. 1
WPC Sandvik CH420:01
Tank unit identification
The figure below shows an example of the tank units identification plate.
The identification plate contains data needed when contacting
Sandvik SRP AB concerning this specific equipment
Identification plate:
1 Type
2 Part number
3 Serial number
4 Order number
Think ahead!
Avoid unnecessary downtime and increased freight charges by ordering parts
well in advance.
Feedback
If you have comments on this wear parts catalog or problems connected to
the crushers documentation, send an e-mail to: [email protected]
Doc. no. R 223.1327 Ver. 1
2007 Sandvik SRP AB
WPC Sandvik CH420:01
Overview with section number references
Cone crusher
Feed hopper
1
5
4
Over-pressure system
12
10
1
2
3
4
5
6
7
8
9
10
11
12
13
Tank unit
Feed hopper
Spider cap
Head nut
Liners
Air filter
Support ring
Dust sealing
Bottomshell wearing
Step bearing set
Chevron packing
Hydroset
Over-pressure system
Tool list
2007 Sandvik SRP AB
11
Doc. no. R 223.1327 Ver. 1
WPC Sandvik CH420:01
1. Feed hopper
1
1
9, 10, 11
17
16
12, 13, 14, 15
2, 3, 4, 5
Pos no
Qty
Part number
Alternative Description
442.9612-00
1
442.9574-00
Feed hopper
840.0049-00
Screw M6S 12x50 8.8 ISO 4014
845.0007-00
Nut M6M M12 8 ISO 4032
847.0002-00
Washer UB-14 SMS 93
847.0147-00
Washer BRB 13x24 HB 200 ISO 7089
442.9598-00
Feed distributer -RH
442.9598-90
Feed distributer-LH
442.9597-01
Holder
840.0045-00
Screw M6S 12x30 8.8 ISO 4017
10
845.0007-00
Nut M6M M12 8 ISO 4032
11
847.0147-00
Washer BRB 13x24 HB 200 ISO 7089
Pos no
Qty.
Part number
Feed hopper distributor
Alternative
Remarks
Each feed hopper distributer consists of:
Fasteners
Distribution parts:
Description
Remarks
442.9613-00
Feed hopper cone
Each feed hopper cone consists of:
442.9574-00
Feed hopper
12
840.0049-00
Screw M6S 12x50 8.8 ISO 4014
13
845.0007-00
Nut M6M M12 8 ISO 4032
14
847.0002-00
Washer UB-14 SMS 93
15
847.0147-00
Washer BRB 13x24 HB 200 ISO 7089
Fasteners for cone parts
16
442.9575-00
Feed hopper cone
Cone for 442.9613-00 EC-EC2
17
442.9606-90
Feed hopper cone
Cone for 442.9613-90 C-EC2
Doc. no. R 223.1327 Ver. 1
2007 Sandvik SRP AB
WPC Sandvik CH420:01
2. Spider cap
5650-0
5685-0,-2
5655-0,-2
5675-0
5150-0
5705-0
5651-0
Cat. no.
Qty.
Part number
5150-0
442.9568-00
Alternative
Arm shield
Description
5650-0
442.8362-01
Spider cap
5655-0
840.0067-00
Screw M6S 16x45 8.8 ISO 4017
5655-2
847.0120-00
Washer TRB 17x30
5651-0
873.0831-00
Seals O-ring 299,3x5,7 SMS 1586
5675-0
442.8363-01
Spider bushing
5685-0
840.0069-00
Screw M6S 16x55 8.8 ISO 4017
5685-2
847.0016-00
Washer BRB 17x30 HB200 SS 7089
5705-0
442.8364-01
Oil seal ring
Remarks
Fasteners for spider cap
Fasteners for spider bushing
3. Head nut
4205-0
4205-2
4025-0
4205-1
4135-0
Cat. no.
Qty.
Part number
Alternative
Description
4025-0
442.6140-01
Mainshaft sleeve
4205-0
442.6194-00
Head nut with burning ring
4205-1
442.6193-00
Inner head nut
4205-2
442.6217-00
Burn ring
4135-0
855.0020-00
Retaining ring
2007 Sandvik SRP AB
Doc. no. R 223.1327 Ver. 1
Remarks
WPC Sandvik CH420:01
4. Liners
6006-0
6005-0
4175-0
Cat. no.
Qty.
Part number
Alternative
Description
4175-0
442.9698-01
02, -03
Mantle A
442.6197-01
02, -03
Mantle B
442.7000-01
-02
Mantle EF
442.9761-01
-02, -03
Mantle HC
442.9569-01
-02, -03
Concave ring EC
442.9587-01
-02
Concave ring C
442.9586-01
-02, -03
Concave ring M
442.9585-01
-02, -03
Concave ring MF
442.9584-01
-02, -03
Concave ring F
442.9583-01
-02
Concave ring EF
6005-0
6006-0
442.9596-01
Filler ring
6005-8
873.1112-00
Sealing compound 0,75 l
6007-2
840.0070-00
Screw M6S 8.8 FZB ISO 4017
6007-3
847.0016-00
Washer BRB 17x30 HB200 ISO 7089
Remarks
(Continued)
Doc. no. R 223.1327 Ver. 1
2007 Sandvik SRP AB
WPC Sandvik CH420:01
The table below illustrates different crushing chambers alternatives
Crushing chamber
(se page 3 Type number)
Concave
6005-0
Mantle
4175-0
Filler ring
6006-0
CH420-F/B/C-25/28/22:1
EC/A
EC extra coarse
442.9569-01 (M1)
442.9569-02 (M2)
442.9569-03 (M7)
EC/B
EC extra coarse
442.9569-01 (M1)
442.9569-02 (M2)
442.9569-03 (M7)
C course
C/A/C
C/B/C
M/A/C
M/B/C
M/HC/C
442.9698-01 (M1)
442.9698-02 (M2)
442.9698-03 (M7)
442.6197-01 (M1)
442.6197-02 (M2)
442.6197-03 (M7)
442.9587-01 (M1)
442.9587-02 (M2)
C course
B
442.9587-01 (M1)
442.9587-02 (M2)
M medium
MF medium fine
442.9585-01 (M1)
442.9585-02 (M2)
MF/HC/C
MF medium fine
442.9585-01 (M1)
442.9585-02 (M2)
HC
F fine
2007 Sandvik SRP AB
C course
C course
C course
442.9596-01
C course
442.9761-01 (M1)
442.9761-02 (M2)
442.9761-03 (M7)
442.9596-01
C course
442.9698-01 (M1)
442.9698-02 (M2)
442.9698-03 (M7)
442.9596-01
C course
442.6197-01 (M1)
442.6197-02 (M2)
442.6197-03 (M7)
HC
442.9584-01 (M1)
442.9584-02 (M2)
442.9584-03 (M7)
442.9596-01
C course
442.9761-01 (M1)
442.9761-02 (M2)
442.9761-03 (M7)
EF extra fine
442.9583-01 (M1)
442.9583-02 (M2)
442.9596-01
442.6197-01 (M1)
442.6197-02 (M2)
442.6197-03 (M7)
442.9584-01 (M1)
442.9584-02 (M2)
442.9584-03 (M7)
EF extra fine
442.9596-01
442.9698-01 (M1)
442.9698-02 (M2)
442.9698-03 (M7)
442.9584-01 (M1)
442.9584-02 (M2)
442.9584-03 (M7)
F fine
442.9596-01
442.9761-01 (M1)
442.9761-02 (M2)
442.9761-03 (M7)
MF/B/C
EF/EF/C
C course
HC
442.9586-01 (M1)
442.9586-02 (M2)
442.9586-03 (M7)
F fine
442.9596-01
442.6197-01 (M1)
442.6197-02 (M2)
442.6197-03 (M7)
F/HC/C
C course
B
442.9586-01 (M1)
442.9586-02 (M2)
442.9586-03 (M7)
M medium
442.9596-01
442.9698-01 (M1)
442.9698-02 (M2)
442.9698-03 (M7)
MF medium fine
442.9585-01 (M1)
442.9585-02 (M2)
F/B/C
C course
A
442.9586-01 (M1)
442.9586-02 (M2)
442.9586-03 (M7)
M medium
442.9596-01
442.6197-01 (M1)
442.6197-02 (M2)
442.6197-03 (M7)
MF/A/C
F/A/C
C course
442.9698-01 (M1)
442.9698-02 (M2)
442.9698-03 (M7)
442.9596-01
C course
442.7000-01 (M1)
442.7000-02 (M2)
Doc. no. R 223.1327 Ver. 1
442.9596-01
WPC Sandvik CH420:01
5. Air filter
(5650-1)
Cat. no.
Qty.
Part number
(5650-1)
5650-1
5650-2
5650-3
Alternative
Description
Remarks
912.0155-00
Filter cartridge 852.514 Mic
Filter complete
912.0114-00
Air filter P 10102 R 1/4
900.0169-00
Nipple 1/4 N8 ISO 49 N8
900.0002-00
Elbow 1/4 A1 ISO 49 A1
6. Support ring
6020-1
6020-2
6020-8
6020-4
6020-0
6105-0 6050-0
10
Cat. no.
Qty.
Part number
Description
Remarks
6020-0
442.1093-01
Alternative
Screw M6S 20x280 8.8
Fasteners for concave
6020-1
845.0203-00
Lock nut ISO 7040 M20 8 FZB
6020-2
442.9572-00
Sleeve
6020-4
442.9573-00
Washer
6020-8
48
863.0065-00
Disc spring 63x31x3.5
6050-0
442.9570-00
Support ring
6105-0
442.9571-00
Dowel pin
Doc. no. R 223.1327 Ver. 1
2007 Sandvik SRP AB
WPC Sandvik CH420:01
7. Dust sealing
4305-0
4350-0
4355-1
4365-1
4365-0,-2
4355-0
Cat. no.
Qty.
Part number
4305-0
442.6906-01
Alternative
Dust seal ring
Description
4350-0
442.6141-01
Retaining ring
4355-0
442.6931-01
Retainer
4355-1
442.6932-01
Scraper
4365-0
11
840.0046-00
Screw M6S 12x35 8.8 ISO 4017
4365-2
11
847.0147-00
Washer BRB 13x24 HB200 ISO7089
4365-1
840.0048-00
Screw M6S 12x45 8.8 ISO 4017
Remarks
Fasteners for dust sealing and scraper
8. Bottomshell wearing liners
1010-2
1320-2
1320-3
1320-4
1320-6
1320-5
1320-2
1320-3
1320-6
1320-4
Cat. no.
Qty.
Part number
1010-1
442.6174-01
Alternative
1320-1 1010-1
Description
Remarks
Pin shaft arm liner
Arm liners
1010-2
442.6175-01
Narrow arm liner
1320-1
442.8902-01
Wearing plates
1320-2
442.8903-01
1320-3
442.8904-01
1320-4
442.8905-01
1320-5
442.8906-01
1320-6
804.0003-00
Rod 1312-00 4-kt 10x60
1320-7
847.0059-00
Washer TBRSB 13,5x36
1320-8
840.0047-00
Screw M6S 12x40 8.8 ISO 4014
2007 Sandvik SRP AB
Doc. no. R 223.1327 Ver. 1
Sold as a complete set
11
WPC Sandvik CH420:01
9. Step bearing set
4075-0
2280-0
2260-0
Cat. no.
Qty.
Part number
Description
Remarks
4075-0
442.6138-01
Alternative
Main shaft step
Consists of (top to bottom):
2280-0
442.6137-01
Step washer
2260-0
442.6139-01
Piston wearing plate
10. Chevron packing
2401-1
2305-0
2540-0 2540-1
12
Alternative
2055-0, -2
Cat. no.
Qty.
Part number
2055-0
840.0019-00
Description
Screw MC6S 8x12 8.8
2055-2
847.0012-00
Washer BRB 8,4x16 HB200 ISO 7089
2305-0
442.6153-00
Chevron packing
2401-0
841.0267-00
Screw MC6S 12x30 8.8 FZB
2540-0
873.0830-00
Seals O-ring 339,3x5,7 SMS 1586
2540-1
873.1274-00
Seal O-ring 319,3x5,7 1586
Doc. no. R 223.1327 Ver. 1
Remarks
2007 Sandvik SRP AB
WPC Sandvik CH420:01
11. Hydroset
1
4
2
Pos. no.
Qty.
Part number
Alternative
Description
Remarks
Main lubrication system
906.0142-00
Filter cartridge
912.0126-00
O-ring seal
912.0129-00
Filter cartridge
906.0373-00
Seat of seals
Hydroset oil system
12. Over-pressure system
1
Pos. no.
Qty.
Part number
912.0139-00
2007 Sandvik SRP AB
Alternative
Description
Remarks
Filter cartridge 852516 Mic
Doc. no. R 223.1327 Ver. 1
13
WPC Sandvik CH420:01
13. Tool list
Cat. no.
14
Qty.
Part number
Alternative
Description
Remarks
442.6637-00
Tool box complete
442.6520-00
Lifting tool
Eccentric bushing
442.6640
Lifting tool
Bottom shell bushing
843.1330-00
Lowering rod with nut M24x500
Removal of piston
845.0012-00
Nut M6M M24 8
Lowering rod M24x500
442.9994-00
Piston stop plate
Holding piston
442.6340-00
Eye bolt
Lift, piston and wearing plate
Mainshaft
899.0132-00
Eye bolt LT M36
899.0147-00
Eye bolt SS 1899-M16
Dust collar
899.0155-00
Eye bolt SS 1899-M12
Eccentric unit, piston
899.0099-00
Eye bolt SS 1899-M10
Bottom shell bush, ecc. bushing
899.0244-00
Eye bolt SS 1899-M8
Eccentric bushing
899.0243-00
Eye bolt LT M6
Mainshaft sleeve
920.0109-00
Ring spanner striking NV 36mm
Screw M24
920.0151-00
Ring spanner striking NV 36 mm
Screw & nut M24
920.0135-00
U-ring spanner NV 36 mm
Screw & nut M24
920.0134-00
U-ring spanner NV 30 mm
Screw & nut M20
920.0022-00
U-ring spanner NV 24 mm
Screw & nut M16
920.0244-00
U-ring spanner NV 18 mm
Screw & nut M12
920.0245-00
U-ring spanner NV 16 mm
Screw & nut M10
920.0186-00
U-ring spanner NV 13 mm
Screw & nut M8
920.0038-00
Socket screw key NV 10
Screw 12
920.0037-00
Socket screw key NV 8
Screw 10
920.0036-00
Socket screw key NV 6
Screw 8
920.0035-00
Socket screw key NV 5
Air bleeder valve
920.0032-00
Socket screw key 5/8
Plug Spider Cap
442.0800-90
Chunk of lead
Check of close side setting
923-0422-00
Feeler gauge 0,05-1mm L=300
904.0585-00
Air bleeder hose
Doc. no. R 223.1327 Ver. 1
2007 Sandvik SRP AB
