THE WING IS BUILT
UPSIDE DOWN
OVER THE PLANS.
Spar splice detail.
This wing should be built all in piece it has no dihedral. If you don't have spars long enough for the wing you can splice them one time on each spar to
make them longer. However you must put the spliced spars in different locations through out the wing to spread out any load on them. It would also be
best to keep them near the spar doublers of the main spar. Make your splice at an angel of about an inch and glue with medium CA. I have done this with
other wings with little strength concerns. If you like you can build it in two sections but you will need to make a ply joiner to slide into the wing from the
center at the rear of the main spar doublers. 5 ply 1/8" birch is a good choose for this. You will need to make a slot for this 1/8 joiner in 2 W-1 ribs. It will
need to pass into two rib bays in each panel. Epoxy the panels centers and joiner with 30 minute epoxy giving you time to work. Then some 2" glass cloth
around the seam with medium CA will hold her together.
3/8" hard wood stock for leading edge
BIRCH PLY JOINER PATTERN
2 1/2" Spinner
.45 to .60 Eengine
A
B
S
Optional 1/8 ply joiner read above.
Wing mount blocks hard wood.
3/16
12 - 16oz. Fuel Tank
SA
L
A
B
"
4
/
"X3
2 1/4" Spinner
1/4 x 1/4 spar stock
1/8 Vertical grain shear
webbing stops here.
1/16" BALSA SHEET
TOP AND BOTTOM
3/32" Sheet rib stock
1/4 x 1/2 Spar Stock
1-C
9
8
7
1
Glue servo mount to
hatch
UGLY STICK 60.COR
Rib#[email protected]"
Rib#[email protected]"
Rib#[email protected]"
Rib#5@15"
Rib#[email protected]"
Rib#[email protected]"
hole in hatch for servo
horn
1/8" ply servo door
hatch
Rib#[email protected]"
Center
section wing
sheeted 1/16"
sheeting.
Rib#[email protected]"
3/8 x 3/8 hard wood stock
for hatch mont
UGLY STICK 60.COR
Rib#[email protected]"
Rib#[email protected]"
1-A
1-A
1-A
1-A
1-B
1-A
1/4 x 1/2 Spar doubler
Rib#[email protected]"
1-B
Rib#[email protected]"
UGLY STICK 60.COR
1/16" cap strip on all ribs
30.0%>4.23"->
S8035.COR/14.1"c/.0625"s/15%thk/0%cmb
Rib#[email protected]"
1-B
Rib#5@15"
1/4 balsa sheet for tips
1/16" PLYWOOD DOUBLER
1/8 Balsa doubler
Holes for servo wires.
1/16" Wing sheeting
Build tap to keep rib level
remove to sheet bottom.
1/4" SHEET BALSA FIN
1/4" wing bolt
1/4 x 1/4 spar stock
A
B
S
Balsa filler for wing
bolt stiffener.
1/4" SHEET BALSA RUDDER
1/8" BALSA SHEET TOP
This is to be cut as part of the vin so it can sit on top of the stabilizer.
30.0%>4.23"->
S8035.COR/14.1"c/.0625"s/15%thk/0%cmb
1/16" sheeting
1/8"X 3/16"
1/16 Rib cap strips
1/4" BALSA SHEET HATCH
1/4" SHEET BALSA ELEVATOR
THE WING IS BUILT
UPSIDE DOWN
OVER THE PLANS.
FUSELAGE SIDES NEED 2
1/4" PLYWOOD INSERT
3/16 sheet balsa
Wing mount blocks hard wood.
Wing leading edge hold down tab.
12 - 16oz. FUEL TANK
BATT. PACK
1/4" BALSA FUSELAGE SIDES
1/8 Balsa doubler
3/8 x 3/8 rear spar stock sand the rear corners just a little to a taper
see wing side view.
Aileron stock glued to
wing
1/8"X 3/16"
1.42
Ply insert
1-B need 6
3/32" PLYWOOD BOTTOM
1-A need 12
PLYWOOD BOTTOM ENDS HERE
F1 - 1/4" PLYWOOD
30.0%>4.23"->
S8035.COR/14.1"c/.0625"s/15%thk/0%cmb
30.0%>4.23"->
S8035.COR/14.1"c/.0625"s/15%thk/0%cmb
8
7
1
2
"CLASSIC UGLY STICK"
Orginally design by Phil Kraft and
re-engineered in
CAD format by Guy Fuller 1997
Newly Cad designed stronger
wing with a true airfoil (see data)
and much more building
information with accurate parts
and measurements drawn by
Jason Niemier 1-9-2007
DeltaCad DEMO
1-B Pattern 6 needed make a few more for repairs.
7
1
2
1/16 Rib cap strips
Wing hold down tab hole.
"CLASSIC UGLY STICK"
1-A Pattern 12 needed.
Holes for servo wires.
1/16" Wing sheeting
3/32" BALSA SHEET BOTTOM
Build tap to keep rib level
remove to sheet bottom.
1-C Center 1/4 ply rib.
THE WING IS BUILT
UPSIDE DOWN
OVER THE PLANS.
Score just a
little here to
make them
easer to
remove
later.
TOP AND BOTTOM
1/16" BALSA SHEET
Orginally design by Phil Kraft and
re-engineered in
CAD format by Guy Fuller 1997
F-3 1/4" SHEET BALSA
3" OR 3-1/4" MAIN WHEELS
CUT OUT TRAILING
EDGE STOCK FOR
STEERING ARM
CLEARANCE
F-2 1/4" ply
F-4 1/4" SHEET
BALSA
F-5 3/16" SHEET F-6 3/16" SHEET F-7 3/16
BALSA
BALSA
Newly Cad designed stronger
wing with a true airfoil (see data)
and much more building
information with accurate parts
and measurements drawn by
Jason Niemier 1-9-2007
3/16
"X3
/4" B
A
LSA
1/4" SHEET BALSA ELEVATOR
Optional 1/8 ply joiner read above.
