G3516B 50Hz Generator Set Engine 7EZ00001-UP(SEBP2906 - 51) - Systems & Compo...
Page 1 of 3
Shutdown SIS
Previous Screen
Product: GEN SET ENGINE
Model: G3516B GEN SET ENGINE 7EZ
Configuration: G3516B 50Hz Generator Set Engine 7EZ00001-UP
Testing and Adjusting
G3500B Engines
Media Number -RENR2268-09 Publication Date -01/08/2012 Date Updated -20/08/2012
i02165404
Exhaust Bypass Valve - Adjust
SMCS - 1057
S/N - 7EZ1-UP
S/N - BGW1-UP
S/N - CEY1-UP
S/N - CFD1-UP
S/N - CME1-UP
S/N - CSC1-UP
S/N - CTK1-UP
S/N - CTW1-UP
S/N - CWD1-UP
S/N - E6T1-UP
S/N - GZP1-UP
S/N - KAD1-UP
S/N - L6H1-UP
S/N - L6J1-UP
S/N - ZBB1-UP
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/15/2018
G3516B 50Hz Generator Set Engine 7EZ00001-UP(SEBP2906 - 51) - Systems & Compo... Page 2 of 3
S/N - ZBC1-UP
The exhaust bypass valve is preset at the factory. However, adjustments may be necessary due to the
following circumstances:
• Replacement of the exhaust bypass valve
• Altitude
• Changes in the ambient temperature
Use the following procedure to adjust the exhaust bypass valve for local conditions.
Illustration 1 g00814530
(1) Plug
(2) Locknut
(3) Adjustment screw
1. Remove plug (1) and the seal. Loosen locknut (2) .
2. Turn adjustment screw (3) clockwise for approximately four turns in order to remove the
function of the exhaust bypass valve. Be careful not to tighten the screw too far.
3. Adjust the engine's exhaust emissions according to Systems Operation/Testing and Adjusting,
"Air/Fuel Ratio Control - Adjust (Oxygen Feedback)" or Systems Operation/Testing and
Adjusting, "Air/Fuel Ratio Control - Adjust (Charge Density)".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/15/2018
G3516B 50Hz Generator Set Engine 7EZ00001-UP(SEBP2906 - 51) - Systems & Compo... Page 3 of 3
Work carefully around an engine that is running. Engine parts that are
hot, or parts that are moving, can cause personal injury.
4. After the desired exhaust emissions are obtained, turn adjusting screw (3) counterclockwise in
order to obtain full load operation with a throttle angle of approximately 70 degrees.
5. When the operation is satisfactory, tighten locknut (2) to the torque that is listed in the engine's
Specifications.
6. Install the seal and plug (1) .
Copyright 1993 - 2018 Caterpillar Inc. Tue May 15 14:33:32 UTC+0430 2018
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/15/2018
