0% found this document useful (0 votes)

9K views874 pages

Vuototecnica

Tecnologia de Vácuo

Uploaded by

Salgado_e_Bento

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

9K views874 pages

Vuototecnica

Tecnologia de Vácuo

Uploaded by

Salgado_e_Bento

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 874

VACUUM

SOLUTIONS
catalogue
INDEX
3 HISTORY OF THE CONCEPT OF A VACUUM
8 INTRODUCTION TO VACUUMS - BASIC PRINCIPLES
9 MEASURING PRESSURE
10 LEVELS OF VACUUM
11 MAIN CHARACTERISTICS OF VACUUMS
12 OPERATING PRINCIPLE OF VACUUM CUPS
13 BOILING TEMPERATURE OF WATER AT VARYING ABSOLUTE PRESSURES
15 PUMP AND VACUUM GENERATOR FLOW RATE AND RELATIVE UNIT OF
MEASUREMENT
MEASURING FLOW RATE
16 FLOW LOSS
ENERGY REQUIREMENTS BASED ON VACUUM PRODUCED
17 THE MAIN VACUUM GENERATORS
20 VACUUM UNIT OF MEASUREMENT CONVERSION TABLE
ABSOLUTE PRESSURE UNIT OF MEASUREMENT CONVERSION FACTORS
21 SOME EXAMPLES OF INDUSTRIAL VACUUM APPLICATION, TODAY
23 EVALUATION OF LIFTING FORCES - CALCULATION EXAMPLES
26 TECHNICAL DATA RELATED TO THE VACUUM CUPS IN THE CATALOGUE
FACTOR OF SAFETY
CHOOSING THE DIAMETER AND NUMBER OF VACUUM CUPS TO BE USED WITH A
LEVEL OF VACUUM HIGHER THAN -75KPA
27 CHOOSING THE DIAMETER OF THE VACUUM CUPS TO BE USED AT DIFFERENT
LEVELS OF VACUUM
28 LIFTING WITH VACUUM CUPS OVER SEA LEVEL
29 SPECIAL CASES OF LIFTING
ENERGY REQUIREMENTS AT DIFFERENT LEVELS OF VACUUM
CHOOSING THE VACUUM CUP SHAPE
30 CHOOSING THE VACUUM CUP COMPOUND
31 GENERAL CHARACTERISTICS OF RUBBER COMPOUNDS
34 TO ORDER VACUUM CUPS
VACUUM CUPS IN STOCK
CHOOSING VACUUM CUP HOLDERS
CHOOSING A PUMP OR VACUUM GENERATOR
36 CHOOSING CHECK VALVES, FILTERS, HOSES, SOLENOID VALVES AND
DISTRIBUTORS
VACUUM CUPS BASED ON BERNOULLI’S THEOREM
37 TECHNICAL MEMO
IP: DEGREE OF PROTECTION OF ENCLOSURES
INTRODUCTION TO VACUUMS
• BASIC PRINCIPLES OF PHYSICS
- What is a vacuum?

The term “vacuum” refers to the physical situation that occurs in an environment where the gas pressure is lower than the
atmospheric pressure.

NEGATIVE PRESSURE AND POSITIVE PRESSURE

Positive pressures are defined as all those with values higher than atmospheric pressure; negative is defined as all those with lower
values. To simplify, let's look at the diagram below:

Patm = Atmospheric pressure

PO = Zero pressure,
absolute vacuum
P+ = Relative
positive pressure
Pass = Absolute pressure
P- = Relative
negative pressure

Since pressure dimensionally represents a force per unit area, its unit of measure is the pascal (symbol Pa), which represents the
pressure that occurs when the force of a newton (symbol N) is exerted on the surface unit, measured square metres (symbol m²).

Therefore:
pascal = newton/metre2 ==> Pa = N/m2

The unit of measurement of pressure, adopted by the International System SI, is the pascal (symbol Pa).

In practice, through, alternative units of measurement are also used such as millibars (mbar), equal to 100 Pa, and Torr or mmHg,
which is equal to 133.322 Pa. The latter is a unit that is not consistent with the International System SI, but is tolerated for
measuring blood pressure.

8
Atmospheric pressure, measured in mbar, decreases as the altitude measured in m changes, as better specified in the diagram
below.

100000
Altitude above sea level (m)

10000

1000

100
0 200 400 600 800 1000 1200

Atmospheric pressure (mbar)

MEASURING PRESSURE

The instruments commonly used for measuring positive pressure are called pressure gauges, while those intended for measuring
negative pressure are called vacuum gauges or vacuum metres.

Comparison of pressure values measured at sea level with the same values measured at different altitudes

mmHg mbar Altitude m -60 KPa -75 KPa -85 KPa -90 KPa -99 KPa
760 1013.25 0 60.0 75.0 85.0 90.0 99.0
750 999.9 111 58.7 73.7 83.7 88.7 97.7
740 986.6 200 57.3 72.3 82.3 87.3 96.3
730 973.3 275 56.0 71.0 81.0 86.0 95.0
720 959.9 467 54.7 69.7 79.7 84.7 93.7
710 946.6 545 53.3 68.3 78.3 83.3 92.3
700 933.3 655 52.0 67.0 77.0 82.0 91.0
690 919.9 778 50.7 65.7 75.7 80.7 89.7
671 894.6 1000 48.1 63.1 73.1 78.1 87.1
593 790.6 2000 37.7 52.7 62.7 67.7 76.7

9
LEVELS OF VACUUM
Depending on the pressure, slightly or much lower than the atmospheric pressure (that is 101325 Pa), the phenomena that occur
can be very different, as the means to obtain and measure that pressure can be very different.
Usually different levels of vacuum are distinguished and given a specific name in relation to the various sub-atmospheric
pressure ranges, as indicated in the following table:

- Rough vacuum, RV: from 105 to 102 Pa

- Medium vacuum, MV: from 102 to 10-1 Pa
- High vacuum, HV: from 10-1 to 10-5 Pa
- Ultra-high vacuum, UHV: from 10-5 to 10-9 Pa
- Extremely-high vacuum, EHV: < 10-9 Pa

The highest level of vacuum reached on earth differs considerably from the absolute vacuum value, which remains a purely
theoretical value.

There is a minimal presence of atoms even in space and therefore in the absence of atmosphere.

In industry, much more simply, vacuums are divided into three application areas, which depend on the level of vacuum required.

- Rough vacuum: Usually used in all those applications where a high intake
air flow and a level of vacuum lower than - 20 Kpa is required

- Industrial vacuum: “Industrial vacuums” are intended as a level of vacuum between - 20 and - 99.9 KPa.
This range covers most applications.

- Process vacuum: Vacuums exceeding - 99.9 KPa

U-shaped Bourdon spring

Mercury vacuum gauge vacuum gauge

McLeod Digital
Mercury vacuum gauge Pirani vacuum metre

10
MAIN CHARACTERISTICS OF VACUUMS
If we take, for example, a bell jar and insert a lit candle, a bell and a glass of water inside it, we will notice that, as we create the
vacuum, the candle will slowly go out, the sound of the bell will fade until it disappears and the water, contained in the glass, will
begin to freeze when the degree of vacuum falls below 6.1 mbar absolute.
At the same time, the atmospheric pressure, acting on the whole surface of the bell jar and also on the underside of the support
surface, will compress it on the latter with a force that is directly proportional to the level of vacuum reached inside it.

The candle blowing out shows that no life is possible in the absence of air.
This characteristics is used in the food industry for food packaging: vacuums in fact preserve food from spores, bacteria and moulds.
The bell phenomenon shows that sound waves are not transmitted in a vacuum and therefore this characteristic can be
exploited in industry to improve sound insulation.
The water contained in the glass tends to cool down because its boiling temperature varies with the surrounding pressure, until it
freezes to below 6 mbar absolute.
Also this characteristic of vacuums, for example, has been used in the field of fruit and vegetable refrigeration. Finally, the
force exerted by the atmospheric pressure on the vacuum chamber is the same force that is used by vacuum cups for vacuum
handling.

11
OPERATING PRINCIPLE OF VACUUM CUPS
When a vacuum forms inside a vacuum cup, the atmospheric pressure that surrounds it exerts a force on it that makes it adhere
to the surface on which it rests.
This force, which is exercised in a uniform and opposite way between the vacuum cup and the external surface of the object on
which it rests, is higher the greater the level of vacuum reached within it.

P1=1013.25 mbar

P 1=250 mbar abs.

P atm=1013.25 mbar P atm=1013.25 mbar

∆P = Patm - P1

Where:
∆P = Pressure differential expressed in mbar
Patm = Atmospheric pressure = 1013 mbar at sea level
P1 = Absolute pressure reached inside the vacuum cup expressed in mbar

From the table inserted in the technical memo, relating to the pressure unit of measurement conversion factors, we note that it is
necessary to develop the following formula to transform the mbar into Kg/cm2,:

Kg/cm2= mbar x 1.02 x 10-3

If we want to calculate, for example, the force exerted by the atmospheric pressure on a vacuum cup inside which a level of vacuum
was created of 250 mbar abs (-75 KPa), we would proceed as follows:

∆P = Patm -P1 = 1013 - 250 = 763 mbar

763 mbar x 1.02 x 10-3 = 0.778 Kg/cm2

From the formulas above, it is easy to deduce that, for the same ∆P, the greater the gripping surface of the vacuum cup, the greater
the force exerted on it by atmospheric pressure.
To detach the vacuum cup from the gripping surface, you will need to exert a force on it that is equal and opposite to that exerted
by atmospheric pressure: in the vacuum handling or gripping sector, a part of this force is used, obtainable by dividing the whole
contrary force for a factor of safety that can vary from 2 to 4, depending on the conditions of the load to be gripped.

12
BOILING TEMPERATURE OF WATER AT VARYING
ABSOLUTE PRESSURES

The boiling temperature of the water varies with the surrounding pressure and therefore, also depending on the altitude.
The diagram below shows the relationship between absolute pressure in mbar and temperature in °C.

100
80
60
Temperature (°C)

40
20
0
-20
-40
-60
0.001 0.01 0.1 1 10 100 1000 10000
mbar

COOLING FRUIT AND VEGETABLE PRODUCTS,

WITH THE USE OF VACUUMS: example

ROBERT BOYLE’S LAW OF GAS:

+volume -pressure
-volume +pressure

Working principle

For rapid and uniform cooling, the treated products must have a high surface/volume ratio (kale, cabbage, lettuce, etc.).
Cooling is based on the relationship between water temperature and vapour pressure.
When the level of vacuum is increased, the water evaporates at an increasingly lower temperature, removing heat from the product.

Properties of water and water vapour at various pressures

Absolute pressure Boiling point Evaporation heat Vapour volume

mbar mmHg °C 2) cal/Kg 1) m3/Kg
1013.25 760 100 533 1.6
482.6 362 80 545 3
68.0 51 38 569 20
20.0 15 22 577 49
13.3 10 11 583 96
6.6 5 5 588 185
6.1 4.6 0 589 204
5.3 4.0 -1.9
4.6 3.5 -3
4.1 3.1 -5
3.3 2.5 -7
2.6 2.0 -9.7
1) Heat required to turn water into vapour without changing temperatures
2) Sublimation point of ice at pressures lower than 4.6 mm Hg / 6.1 mbar

13
Vacuum and temperature values detected during the process

mbar °C
15 VACUUM

13
PRODUCT TEMPERATURE

10
12
9

7
10 END OF VACUUM
6
AUTOCLAVE DOOR OPENING
5

4
6.56 FINAL TEMPERATURE OF THE
3
PRODUCT BROUGHT
2 INTO THE COLD ROOM
1
Time in
minutes 0 5 10 15 20 25 30 35 40

The quantity of water evaporated represents about 1% for every 5-6 °C that the temperature is lowered.
The vacuum is obtained with a high vacuum pump and the vapour developed is condensed on a refrigerating coil. The level of
vacuum and the temperature must be detected by programmable precision instruments with direct reading to obtain the ideal
cooling cycle based on the product.
The temperature value must be detected by an auxiliary safety device, which will have the function of protecting the product from
the risk of frost.
These are just some of the features of vacuums commonly used in industry.

14
PUMP AND VACUUM GENERATOR FLOW RATE AND RELATIVE UNIT OF
MEASUREMENT

The volumetric quantity of fluid sucked in by the pump or vacuum generator, in the unit of time, is called the flow rate.
Definition: Q, q, = V/t (volume/time)
In the International System SI, the flow rate is measured in m3/s.
Current multiples of use are: l/min, l/s, m3/h.

FLOW RATE UNIT OF MEASUREMENT CONVERSION FACTORS

= m3/h = m3/min = l/h = l/min = cfm

m /h
3
x 1 0.016 103
16.6 0.588
m3/min x 60 1 6x104 103 3.53x10
l/h x 10-3 1.66x10-5 1 0.016 5.88x10-4
l/min x 60x10-3 10-3 60 1 3.53x10-2
cfm x 1.699 2.83x10-2 1699.0 28.314 1

MEASURING FLOW RATE

The instruments commonly used for measuring the flow rate are called flowmeters.
Based on the same operating principle, asameters are very precise laboratory
instruments, which take their name from the company that produces them: the ASA
company.
Flowmeters and asameters are variable area meters for fluids based on the Bernoulli
principle.
Asameters consist of a glass tube and a body called a float.
The tube is tapered inside and calibrated with very tight tolerances. Inside the tube is
a suitably shaped float with a diameter slightly smaller than the minimum diameter
of the tube.

If we run a fluid with ascending motion through the system, the float moves into the
tube and stops at a certain height corresponding to a well-defined flow.
A scale engraved on the glass tube lets you read this flow rate at the point where the
float stops.

Flow

Tube

Glass

Float

Asameter operating
Flow diagram

15
Flow loss

The diagram shows the flow loss value through a 1 mm2 cross-section hole at different levels of vacuum, measured in Nl/s (Normal
litres per second, the unit of measurement of the flow rate referring to the normal atmospheric pressure level of the sea).

0.2
0.18
0.16
0.14
Flow rate (Nl/s)

0.12
0.1
0.08
0.06
0.04
0.02
0
0 20 40 60 80 100

Vacuum (-KPa )

To obtain the total loss, simply multiply the flow rate value indicated in the diagram, in correspondence with the available level of
vacuum, for the total loss section.

Energy requirements based on vacuum produced

The diagram shows the increase in energy requirements as the level of vacuum increases.
As can be seen, the energy demand drastically increases above -90 Kpa; for this reason, it is advisable to stay below this value.
(Law by Robert Boyle 1627-1691)

100
90
80
70
Vacuum (-KPa)

60
50
40
30
20
10
0
0 10 100 1000 10000 100000 1000000

Energy requirements

16
THE MAIN VACUUM GENERATORS
In industry, much more simply, vacuums are divided into three application areas, which depend on the level of vacuum required.

- Rough vacuum: Used in all those applications where a high intake air flow and a level of vacuum lower than - 20 KPa is
required.
In this application area, impeller-type electromechanical pumps are usually used, such as centrifugal fans
and side channel blowers, pneumatic and similar flow generators.
Screen printing on fabrics, for example, is one of the typical applications that require a low level of vacuum.

Suction
or compression fitting

Electric motor

Side channel blower

Impeller
fins

Side channel Air flow

in the side channel

U
R

P = COMPRESSED AIR CONNECTION

R = AIR EXHAUST
U = VACUUM CONNECTION Pneumatic vacuum generator

17
- Industrial vacuum: “Industrial vacuums” are intended as a level of vacuum between --20 KPa and -99.9 KPa. This range covers
most applications.
Industrial vacuums are mainly produced by rotary vane, liquid ring, piston, lobe, etc. vacuum pumps, all driven
by electric or petrol or hydraulic motors, and vacuum generators based on the Venturi principle, powered
by compressed air. Industrial vacuums are used from handling with vacuum cups to thermoforming, from
vacuum clamping to vacuum packaging, etc.

Rotary vane vacuum pumps

DELIVERY IMPELLER

IMPELLER
BODY

BODY
AXIS
AND LIQUID RNG. SUCT.
PLANE

LIQUID RING IMPELLER

Liquid ring vacuum pumps

P R

P = COMPRESSED AIR CONNECTION

R = AIR EXHAUST
U
U = VACUUM CONNECTION Multi-stage pneumatic vacuum generator

18
- Process vacuum: Vacuums exceeding -99.9 KPa.
The main generators of this level of vacuum are two-stage rotary vane pumps, eccentric rotor pumps,
Roots pumping units, turbomolecular pumps, diffusion pumps, cryogenic pumps, etc.

The most common applications are freeze-drying, metallisation and vacuum heat treatments. Those of a
scientific nature, however, include spatial simulations.

Roots pump

VACUUM

Diffusion pump

19
VACUUM UNIT OF MEASUREMENT CONVERSION TABLE
mbar torr. inch. Hg mmHg bar -KPa mbar
abs. abs. vacuum vacuum vacuum vacuum abs.

1000
1013,25
760
0
0
0
0
1000
1013,25
5
500 10
500 15 0,5 50 500

20 500

100
25
26
100 27 0,9 90 100
700
50 28

50 0,95 95 50

10 29,5
750
10 29,7 0,99 99 10
5 755
5 0,995 99,5 5

29,9

1.33 1 759 1,33

1 0,75 759,24 0,999 99,9 1

29,97
0,5

0,5 0,9995 99,95 0,5

29,99

0,1 759,86
0,133 0,133
0,1 0,075 759,9 0,9999 99,99 0,1
29,997

0,05
0,05 0,99995 99,995 0,05

29,999

0,0133 0,01 759,98 0,0133

0,01 0,0075 29,9997 759,99 0,99999 99,999 0,01

ABSOLUTE PRESSURE UNIT OF MEASUREMENT CONVERSION FACTORS

= psi = Kg/cm2 = Pa
= mbar = bar = torr = inch. Hg = atm = mm H2O = m H2O
(lbf/in ) 2
(at) (N/m2)

mbar x 1 10-3 0,75 2,95x 10-2 14,5 x 10-3 9,87 x 10-4 1,02 x 10-3 10,2 1,02 x 10-2 100,0
bar x 1000,0 1 750,0 29,53 14,6 0,987 1,02 10197,0 10,19 100000
torr x 1,33 1,33 x 10-3 1 3,94 x 10-2 1,93 x 10-2 1,316 x 10-3 1,359 x 10-3 13,59 1,359 x 10-3 133,32
inch. Hg x 33,9 33,9 x 10-3 25,4 1 0,491 3,34 x 10-2 3,45 x 10-2 345,0 0,345 3386,0
psi (lbf/in ) 2
x 68,9 6,89 x 10 -2
51,7 2,04 1 6,8 x 10 -2
7,03 x 10 -2
703 0,703 6897
atm x 1013,25 1,013 760,0 30,0 14,696 1 1,033 10332 10,332 101325,0
Kg/cm2 (at) x 981 0,981 735,6 28,96 14,2 0,968 1 10000 10 98067,0

mm H2O x 9,81 x 10-2 9,81 x 10-5 7,35 x 10-2 2,89 x 10-3 1,42 x 10-3 9,67 x 10-5 10-4 1 10-3 9,8067
m H2O x 98,067 9,81 x 10 -2
73,5 2,89 1,42 9,67 x 10 -2
10 10000 1 9806,7
Pa (N/m2) x 0,01 10-5 7,5 x 10-3 2,95 x 10-4 1,45 x 10-4 9,87 x 10-6 1,02 x 10-5 0,102 1,02 x 10-4 1

Example: To transform 10 mbar in Torr = 10 x 0.75 = 7.5 Torr

20
SOME EXAMPLES OF INDUSTRIAL VACUUM APPLICATION, TODAY

Vacuum cup handling of sheet metal, glass, marble, OCTOPUS vacuum gripping systems Transfer of powders, granulates, liquids, etc.
wood, etc.

Filling at constant volume Egg handling with vacuum cups Labelling - vacuum cup gripping

Bag opening with vacuum cups in the Packaging sector Vacuum impregnation Vacuum clamping for machining centres

21
SEALING PUMP
FOR
RESIN SUCTIONED VACUUM
FROM VACUUM
RESIN VACUUM BAG

MOULD

Vacuum cylinders to moving sheets Vacuum moulding with resin infusion

PUMP PUMP
FOR FOR
VACUUM VACUUM
SUCTION
VALVE

COMPOSITE FIBRES VACUUM BAG

SEALS

Vacuum packaging Vacuum pressing

Typographic sector

The vacuum-aided handling and clamping sector is undoubtedly the one most gratifying to us and the one in which we have
developed our greatest expertise, in our over forty years of activity.
The description of vacuum cups, indispensable tools for vacuum handling, design notes, recommendations for choosing the best
pumps and accessories and the technical memo will aid even the least experienced sector designers in safely sizing handling
vacuum equipment.

22
EVALUATION OF LIFTING FORCES - CALCULATION EXAMPLES

For a correct dimensioning of a vacuum cup handler, it is firstly important to know and assess the features of the load to be
handled.
- Nature
- Dimensions and shape
- Mass
- Roughness and unevenness of the gripping surface
- Permeability
If we take, for example, a steel sheet with the following dimensions:
- Length 4.0 m
- Width 1.8 m
- Thickness 3.0 mm

The formula for calculating the mass is as follows:

m = A x B x C x ps

Where:
m = Mass (kg)
A = Length (m)
B = Width (m)
C = Thickness (m)
Ps = Specific weight (for steel = 7860 Kg/m3)

We will therefore have:

m = 4 x 1.8 x 0.003 x 7860 = 169.77 Kg

Once the mass has been determined, the force of the vacuum cups required for move it is calculated by evaluating its direction and
the position of the vacuum cups with respect to the load, without disregarding the acceleration or deceleration forces acting on
the moving load and the friction that develops between the vacuum cups and the gripping surface.
The most common cases are:

1st case - Horizontal vacuum cups, vertical force.

The vacuum cups rest horizontally on the load to be lifted.

In this case, the force of the vacuum cups required to move our steel sheet is calculated according to the following formula:

F = m x (g + a) x η

23
Where:
F = Force of the vacuum cups (N)
m = Mass (Kg)
g = Force of terrestrial gravity (9.81 m/s2)
a = Acceleration or deceleration (5 m/s2, for this case)
η = Factor of safety (minimum 2 for our example; for materials with rough, irregular and
permeable surfaces, the value to be considered can vary from 2.5 to 3)

F = 169.77 x (9.81 + 5) x 2 = 5028.58 N

2nd case - Horizontal vacuum cups, horizontal force.

The vacuum cups rest horizontally on the load to be lifted laterally.

In this second case, the force of the vacuum cups required to move our steel sheet laterally is calculated according to the following
formula:

F = m x (g + a/μ) x η

Where:
F = Force of the vacuum cups (N)
m = Mass (Kg)
g = Force of terrestrial gravity (9.81 m/s2)
a = Acceleration or deceleration (5 m/s2, in this case)
μ = Coefficient of friction = 0.1 for oiled surfaces
= 0.2 - 0.3 for wet surfaces
= 0.5 for wood, glass, metal and marble
= 0.6 for rough surfaces
η = Factor of safety (minimum 2 for our example)

Note: The coefficients of friction indicated are purely indicative. During the design phase, the values relating to the materials of the
loads to be handled must be checked carefully.

Inserting the values indicated in the formula, we have:

F = 169.77 x (9.81 + 5/0.5) x 2 = 6726.28 N

24
3rd case - Vertical vacuum cups, vertical force.

The vacuum cups rest vertically on the load to be moved vertically.

In this third case, the force of the vacuum cups required to move our steel sheet vertically is calculated according to the following
formula:

F = (m/μ) x (g + a) x η

Where:
F = Force of the vacuum cups (N)
m = Mass (Kg)
μ = Coefficient of friction (0.5 in this case)
g = Force of terrestrial gravity (9.81 m/s2)
a = Acceleration or deceleration (5 m/s2, in this case)
η = Factor of safety (2 for our example)

Developing our formula, we have:

F = (169.77/0.5) x (9.81 + 5) x 2 = 10057.17 N

As you can see, the third example is always the one that requires the greatest force and, therefore, the utmost attention is
recommended during the design phase for all the factors required.

25
TECHNICAL DATA RELATED TO THE VACUUM CUPS
IN THE CATALOGUE
For practical reasons and to simplify the choice of vacuum cups, all the lifting force values, shown in the table, are expressed in Kg
and calculated based on the following formula:

SxP
F=
η

Where:
F = Lifting force expressed in Kg
S = Vacuum cup gripping surface, expressed in cm2
P = Force exerted by atmospheric pressure, depending on the level of vacuum, expressed in Kg/cm2
η = Factor of safety

FACTOR OF SAFETY
Our vacuum cups have been designed to theoretically suspend a load equal to three times the force value indicated in the tables.

The values shown were obtained by considering:

P = 0.75 Kg/cm2: value developed from a level of vacuum of approximately 250 mbar abs. (-75 KPa).
η = 3: factor of safety, valid when the gripping surface of the vacuum cups is horizontal, the surface is smooth and impermeable
and the acceleration or deceleration of the moving load is less than 10 m/s2.

If we consider, for example, a vacuum cup ø 60 mm (item 08 60 10) whose gripping surface S is 28.26 cm2, we will obtain the
following by developing the formula shown above:

28.26 x 0.75
F= = Kg 7.06
3

which is the value shown in the table, next to the item of the vacuum cup used as an example.

VACUUM CUPS WITH SUPPORT

Item Force A D M Vacuum cup Support Weight
Kg Ø Ø Ø item item g
08 60 10 * 7.06 G1/4” 60 M8 01 60 10 00 08 22 20.8
08 60 11 * 7.06 G1/8” 60 -- 01 60 10 00 08 44 20.0

* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

CHOOSING THE DIAMETER AND NUMBER OF VACUUM CUPS TO BE USED

WITH A LEVEL OF VACUUM HIGHER THAN -75 KPA
As the weight of the object to be handled is known, the number of vacuum cups to be used and their diameter will be determined
with the help of the tables relating to the vacuum cups and at the discretion of the designer, depending on the application.

Example: Suppose we have to lift an oil drum weighing 140 kg with a single vacuum cup and with a level of vacuum available greater than
-75 KPa. From the tables relating to the vacuum cups, we find that those with Ø 300 mm (item 08 300 10) are suitable for solving our problem,
since their lifting force is 176.6 kg and therefore higher than the required weight of 140 kg.

26
If, on the other hand, the load to be lifted is a steel plate, the weight of which is also 140 kg, it will no longer be possible to use a
single vacuum cup, since the sheet would flex, but we will need to use at least 4 vacuum cups or, better yet 6, if we want to keep
the sheet perfectly taut.

VACUUM CUPS WITH VULCANISED SUPPORT

Force A B C D E F G H M N Material Weight
Item Kg Ø Ø Ø Ø Ø support Kg
08 110 15 M8 * 23.7 74 70 M8 110 2 14 10 26 26.0 G1/4” steel 0.35
08 110 15 * 23.7 74 70 M12 110 2 14 10 26 26.0 G1/4” steel 0.33
08 115 15 * 45.0 115 110 M12 150 2 14 10 26 40.0 G3/8” steel 0.83
08 200 10 * 78.5 164 160 M12 200 3 14 11 28 47.5 G3/8” steel 1.75
08 250 10 * 122.6 214 210 M12 250 3 14 11 28 72.5 G3/8” steel 3.00
08 300 10 * 176.6 266 260 M16 300 5 15 11 31 89.0 G1/2” steel 4.70
08 350 10 * 240.4 316 310 M16 350 5 15 11 31 89.0 G1/2” steel 6.60

* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

If you want to use 4 vacuum cups, you will have to choose with a Ø 150 mm (item 08 150 10, 08 150 36, 08 150 74,08 150 15, etc.),
each having a lifting force of 45 kg, so together they are able to lift a maximum load of 180 kg.
If you instead want to use 6 vacuum cups, their diameter can be reduced to 110 mm (item 08 110 10, 08 110 24, 08 110 58, 08 110
15, etc.), with a lifting force of 23.7 kg each, so together they are able to lift a maximum load of 142.2 kg.

CHOOSING THE DIAMETER OF THE VACUUM CUPS TO BE USED AT

DIFFERENT LEVELS OF VACUUM
In the event that the value of the vacuum differs from that used for calculation of the forces, you can determine the diameter of
the vacuum cups (and consequently their gripping surface) by solving the following equation:

mxη
D = 113 x
Pxn

Where:
D = Diameter of the vacuum cup, expressed in mm
m = Mass of the load to be lifted, expressed in Kg
P = Level of vacuum, expressed in -KPa
η = Factor of safety, never less than 2
n = Number of vacuum cups to use

27
If we take the example described above, relating to the 140 kg sheet, considering the use of 6 vacuum cups at a level of vacuum of
-60 KPa and a factor of safety 3, we will obtain:

140 x 3
D = 113 x = 122 mm
60 x 6

6 vacuum cups with a diameter equal to or greater than 122 mm will be therefore be required to solve our problem.

LIFTING WITH VACUUM CUPS OVER SEA LEVEL

With higher altitude, atmospheric pressure decreases according to the values shown in the table below. To detect the level of
vacuum, the vacuum gauge is normally calibrated to the atmospheric pressure present at sea level, which is 1013.25 mbar.

BAROMETRIC PRESSURE VALUES OF THE VACUUM GAUGE AT 1013.25 mbar

mmHg mbar Altitude m -60 KPa -75 KPa - 85 KPa -90 KPa -99 KPa
760 1013.25 0 60.0 75.0 85.0 90.0 99.0
750 999.9 111 58.7 73.7 83.7 88.7 97.7
740 986.6 200 57.3 72.3 82.3 87.3 96.3
730 973.3 275 56.0 71.0 81.0 86.0 95.0
720 959.9 467 54.7 69.7 79.7 84.7 93.7
710 946.6 545 53.3 68.3 78.3 83.3 92.3
700 933.3 655 52.0 67.0 77.0 82.0 91.0
690 919.9 778 50.7 65.7 75.7 80.7 89.7
671 894.6 1000 48.1 63.1 73.1 78.1 87.1
593 790.6 2000 37.7 52.7 62.7 67.7 76.7

Developing the formula previously described:

∆P = Patm - P1

And again considering a level of vacuum equal to 250 mbar abs. (-75 KPa) inside the vacuum cup, the force exerted by the
atmospheric pressure on the vacuum cup, at an altitude of 1000 metres above sea level, will be:

∆P = 894.6 - 250 = 644.6 mbar

Equal to:
644.6 mbar x 1.02 x 10-3 = 0.657 Kg/cm2

As can be seen, from a force of 0.778 Kg/cm2 available at sea level, we have gone to 0.657 Kg/cm2 at 1000 metres of altitude. This
confirms that, with decreasing atmospheric pressure, the available force also decreases.
Therefore, in the design phase, always consider the altitude of the place where the vacuum cup lifting system will be installed.

28
SPECIAL CASES OF LIFTING
In all those cases where:
- The gripping surface of the vacuum cups is vertical
- The acceleration and deceleration of the load to be handled is greater than 10 m/s2
- The gripping surface is very rough or uneven
- The load to be supported is permeable

The factor of safety value must be increased according to each of these. Our technicians are at your disposal to define this value.

ENERGY REQUIREMENTS AT DIFFERENT LEVELS OF VACUUM

As we have seen in the previous chapters, when we create a vacuum inside a vacuum cup resting on a surface, the atmospheric
pressure that surrounds it acts on it more forcefully the greater the level of vacuum reached.
The lifting force is directly proportional to the gripping surface and the level of vacuum. If the level of vacuum changes from 60%
to 90%, the lifting force increases 1.5 times, while the required energy increases 10 times according to Boyle's law.
To reduce energy consumption, it is preferable to limit the level of vacuum and, where possible, increase the gripping surface of
the vacuum cup.

CHOOSING THE VACUUM CUP SHAPE

Vacuum cups are available in various conformations, each of which is able to meet the various needs that are encountered in the
design phase, in the movement and handling of objects and loads of the most disparate forms. They can be chosen according to
different characteristics, listed below:

Cupped vacuum cups These are the most common vacuum cups, used in all industry sectors for the handling
of plastic objects, cardboard boxes, wood panels, thin sheets of metal or glass, etc.,
with very low weight and even rough or irregular surfaces.
They are available in different diameters starting from 4 mm and up to 100 mm.
They are not recommended for vertical handling of heavy objects.

Bellows vacuum cups The particular shape of these bellows cups allows them to quickly crumple up when
in contact with the surface of the load to be lifted and in presence of a vacuum. This
quick movement prevents the load below from remaining stuck to the surfaces or load
underneath. Thanks to this particular feature, these bellows cups are recommended for
handling paper and cardboard sheets, thin metal sheets, wooden panels, glass sheets
etc. Thanks to their great flexibility, they can also be used to compensate flatness errors
or for gripping on inclined surfaces. They are not suitable for vertical handling of heavy
loads.

Flat, round and rectangular vacuum cups Vacuum cups suitable for vertical or horizontal movement of large loads such as
marble or granite slabs.

29
Vacupredator vacuum cups For the gripping of bags, packs and flexible containers in paper or plastic, containing
powders, granulated products, loose or liquid products. These new vacuum cups
have been designed and manufactured to safely grip even the most difficult and
irregular packages.

Foam rubber vacuum cups These vacuum cups are suitable for handling and gripping loads with raw or very
rough surfaces such as sawn, bush-hammered or flamed marble, textured, non-slip
or profiled metal sheets, striped Plexiglass, raw cement manufactures, garden tiles
with fret, etc.

Maxigrip vacuum cups Vacuum cups with a high coefficient of friction, suitable for use in the handling in all
directions of oiled sheets, marble and wet glass, slabs and, in general, loads subject
to high acceleration and deceleration during movement. Especially recommended
for the AUTOMOTIVE sector. Available in various sizes, in round and elliptical flat and
round and elliptical bellows.

Circular rim cups These cups have been designed to meet the need of lifting objects with a central hole.
Their very thin lip allows them to grip very rough surfaces, such as grinding wheels
and discs. They are particularly recommended for CDs, perforated discs, toothed
wheels, pulleys and other similar objects.

Elliptical flat vacuum cups These are recessed on moulders in order to hold a side of the cardboard box during
the moulding process by means of traditional cups on the opposite side. Once
assembled with their support, however, they can be used for handling boxes, plastic
objects or anything with a limited gripping surface.

Special vacuum cups These cups have been designed to solve many of the gripping and handling problems
we have encountered in over forty years of activity. They differ from all the other cups
for the variety of their shapes. They are suited for gripping CDs, labels, bags, paper
or plastic sheets, stickers, chocolates, cardboard, tiles, small metal objects, plastic
objects, etc.

Further information is available on the catalogue pages relative to the vacuum cups listed.

CHOOSING THE VACUUM CUP COMPOUND

The vacuum cup compounds are chosen with the aid of the technical tables, according to the individual applications and after
having carefully evaluated:
- The weight and dimensions of the load
- The intensity and severity of work cycles
- The roughness of the surface of the load to be lifted and its temperature
- The presence of oils, solvents, chemicals or other corrosive elements on the gripping surface
- If the work environment is outdoors, in contact with atmospheric agents or indoors, in the presence of high or low temperatures
- If the product to be handled is food, so the vacuum cups must comply with certain standards
- If absolutely no marks or prints must be left on the gripping surface
- If electrostatic charges must be dissipated from the gripping surface

30
GENERAL CHARACTERISTICS OF RUBBER COMPOUNDS
TRADE INTERN. VT POSITIVE NEGATIVE TEMPERATURE OF CHEMICAL FOOD
COLOUR HARDNESS USE
NAME CODE CODE CHARACTERISTICS CHARACTERISTICS USE RESISTANCE STANDARDS

The excellent mechanical

Limited ozone
Resistance to characteristics of this compound allow
Highly resistant to oil, heat resistance, if Non-toxic vacuum
NITRILE OR mineral oils, the vacuum cups to withstand heavy-
NBR A and ageing. Low permanent untreated. Black From -40 to + 130°C 60 - 70° Sh.A cups can be
OIL-RESISTANT hydrocarbons, duty work such as tears, crushing,
deformation and low gas Low dielectric produced upon
RUBBER water, vapour, gas bumps, etc. They are suitable for
permeability. strength, request.
and vegetable oils. gripping metal plates, glass and loads
Low resilience.
with a smooth surface.

The vacuum cups produced with

Excellent resistance to wear,
Resistance to this compound are able to withstand
ageing, chlorine-containing
Black chlorine-containing heavy-duty work such as tears,
oils, grease and petrol. Low dielectric From -40 to + 170°C 60 - 75° Sh.A Production of non-
HNBR B Red mineral oils, crushing, bumps, etc. They are suitable
BENZ RUBBER Low permanent deformation. strength, toxic vacuum cups
hydrocarbons, for gripping metal plates, glass and
Does not leave marks on Low resilience. not recommended.
water, vapour, gas loads with a smooth surface. Especially
the gripping surfaces of the
and vegetable oils. recommended for the AUTOMOTIVE
vacuum cups.
sector.

Biond compound with good

elastic yield and resistance to Fair resistance to Vacuum cups produced with this
BIOND Non-toxic vacuum
wear, cutting and tearing. Has sea water, acids compound are suitable for gripping
NON- ---- BA Poor resistance to Grey From -30 to + 80°C 45 - 60° Sh.A cups can be
the property of not leaving and medium marble, wood, glass, metal sheets, etc.,
MARKING oils and heat. produced upon
stains, concentration without leaving marks or prints on the
RUBBER request.
marks or prints on the alkalis. gripping surfaces.
gripping surfaces.

In addition to the normal use of the

Highly resistant to oil, heat Excellent resistance
Limited ozone NBR compound, the vacuum cups
ANTI-STATIC and ageing. Low permanent to mineral oils, Production of non-
NBR-AS AS resistance if Black From -40 to + 130°C 60 - 70° Sh.A made with this compound can be used
NITRILE deformation. Highly hydrocarbons, toxic vacuum cups
untreated. in all those cases where it is necessary
RUBBER conductive and anti-static water, vapour, gas not recommended.
Low resilience. to dissipate electrostatic charges
compound. and vegetable oils.
accumulated on the gripping surfaces.

Fair resistance to The flexibility of the compound allows

Excellent elastic yield and Non-toxic vacuum
sea water, acids these vacuum cups to grip on rough
NR N resistance to wear, cutting Poor resistance to Black From -70 to + 80°C 45 - 50° Sh.A cups can be
PARA RUBBER and medium and irregular surfaces. They are
and tearing. Exceptional oils and heat. produced upon
concentration suitable for wood, cardboard, marble,
elongation at break. request.
alkalis. bricks, glass and plastic.

31
32
TRADE INTERN. VT POSITIVE NEGATIVE TEMPERATURE OF CHEMICAL FOOD
COLOUR HARDNESS USE
NAME CODE CODE CHARACTERISTICS CHARACTERISTICS USE RESISTANCE STANDARDS

The higher flexibility of the compound

allows these vacuum cups to grip on
Non-toxic vacuum
very rough and irregular surfaces.
NATURAL NR NG The same compound Poor resistance to Beige From -50 to + 70°C 40 - 45° Sh.A As NR described cups can be
The vacuum cups made with this
RUBBER described above, untreated. ageing, oils and heat. above. produced upon
compound are recommended for
request.
gripping paper, cardboard, plastic,
plastic film for packaging, etc.

Fair resistance to
Excellent elastic yield and The softness of the foam rubber makes
sea water, acids Compound not
GERANIUM NR OF resistance to tearing. Poor resistance to Orange From -40 to + 80°C 25 - 30° Sh.A it possible to create vacuum cups for
and medium recommended for
FOAM RUBBER Exceptional elongation at ageing, oils and heat. gripping loads with raw or very rough
concentration food use.
break. surfaces.
alkalis.

Modest mechanical It is possible to Silicone vacuum cups are used in

Neutral Excellent resistance
Perfect performance at high properties. Can leave produce vacuum the food and electronics industry, in
VMQ S White From -50 to +300°C 40 - 45° Sh.A to chlorinates,
SILICONE and low temperatures. marks on the gripping cups according to packaging and in all those cases where
Red solvents, ozone,
Conductive compound. surfaces of vacuum FDA, BGA, TSCA, the contact surface has very high or
oxygen and U.V.
cups. etc. food standards. very low temperatures.

Modest mechanical Anti-static silicone vacuum cups are

Perfect performance at low
properties. Compound not used in the electronics, the recording
ANTI-STATIC VMQ-AS SAS and high temperatures. Black From -50 to + 200°C 40 - 45° Sh.A Similar to VMQ
Can leave marks on recommended for industry and in all those cases where it
SILICONE Highly conductive and anti- silicone compound.
the gripping surfaces food use. is necessary to dissipate electrostatic
static compound.
of vacuum cups. charges from the gripping surface.

Perfect performance at high

The stabilised silicone vacuum
and low temperatures.
cups are widely used in the ceramic
Conductive and non- Modest mechanical Neutral It is possible to
STABILISED VMQ-SS SS From -50 to + 300°C 40 - 45°Sh.A Similar to VMQ industry and in all those cases where,
marking compound. properties. White produce vacuum
SILICONE silicone compound. in addition to withstanding high
Does not leave marks cups for food use.
temperatures, marks or prints must not
or prints on the gripping
be left on the gripping surfaces.
surfaces.

The chemical
composition of
the compound
contains exclusively
Magnetic silicone vacuum cups are
Perfect performance at high Modest mechanical substances
Excellent resistance used in the food industry and have
and low temperatures. properties. Can leave authorised by
MAGNETIC ---- SMG Black From -50 to + 250°C 45 - 50° Sh.A to chlorinates, the characteristic of being easily
Highly conductive, marks on the gripping regulation FDA
SILICONE solvents, ozone, detectable by metal detectors used for
magnetically detectable surfaces of vacuum CFR 21: 177-
oxygen and U.V. food protection in case of breakage or
compound. cups if not stabilised. 2600 “ METAL
accidental detachment.
DETECTABLE
COMPOUND - HEAT
CONDUCTIVITY
COMPOUND “
TRADE INTERN. VT POSITIVE NEGATIVE TEMPERATURE OF CHEMICAL FOOD
COLOUR HARDNESS USE
NAME CODE CODE CHARACTERISTICS CHARACTERISTICS USE RESISTANCE STANDARDS

Excellent resistance
Excellent resistance to
to sunlight, flame and This compound is used to produce
chemical deterioration; perfect
Green high temperatures, to Production of non- vacuum cups that are highly qualified
FKM V for lubricants and heat. Poor resistance to From -20 to + 300°C 50 - 60° Sh.A
VITON® Brown aromatic and aliphatic toxic vacuum cups for the mechanical, oil, chemical,
Good compression alkalis and ketones.
hydrocarbons, to not recommended. pharmaceutical, aeronautical and
performance and elastic yield.
chemical agents and nuclear industries.
Does not leave marks.
chlorinated solvents.

Very high resistance to

VULKOLLAN® Poor resistance to Ivory Production of non- Suitable for producing vacuum cups
AU-EU PU abrasion, traction, bending From -30 to + 100°C 60 - 70° Sh.A Excellent resistance to
POLYURE- water, alkalis and Blue toxic vacuum cups subjected to heavy-duty, intense and
and oils. Does not leave petroleum products.
THANE acids. not recommended. continuous use.
marks.

EPDM vacuum cups are recommended

Excellent resistance to heat,
for machines operating outdoors, in
atmospheric agents and Good resistance to Production of non-
EPDM EPDM Black From -60 to + 150°C 50 - 70° Sh.A contact with atmospheric agents and
DUTRAL® ageing. Poor elasticity. aggressive chemicals toxic vacuum cups
sea water.
Excellent resistance to low and oxygen. not recommended.
Excellent performance in contact with
temperatures.
printing inks and solvents.

Fair resistance to oils. Excellent resistance to Vacuum cups made with this
Poor elastic yield.
Excellent resistance to petroleum products, Production of non- compound are used in the electrical
CR NE Risk of permanent Black From -20 to + 120°C 50 - 70° Sh.A
NEOPRENE® ozone, sea water and ageing. sunlight, atmospheric toxic vacuum cups industry and on handling systems
deformation over
Good resistance to cutting, agents, ozone and not recommended. that operate outside, in contact with
time.
abrasion and combustion. flames. atmospheric agents.

Fair resistance to oils. The softness that characterises this

Excellent resistance to
Excellent resistance to Poor elasticity. foam rubber allows for the use of
NEOPRENE® CR NF Black From -20 to + 80°C 30 - 35 Sh.A oil products, sunlight, Not recommended
ozone, sea water and ageing. Tendency to deform vacuum cups for gripping coarse or
FOAM RUBBER atmospheric agents, for food use.
Good resistance to cutting, over time. very rough surfaces operating outside
and ozone.
abrasion and combustion. in contact with atmospheric agents.

Low resistance to The softness of this rubber foam

Excellent resistance to heat, Good resistance to Not advised for
EXTRA SOFT EPDM SB oils and modest Black From -40 to + 130°C 8 ÷ 10 Sh.A makes it suitable for use on grip
atmospheric agents, low aggressive chemicals direct contact with
FOAM RUBBER mechanical surfaces for loads with coarse or very
temperatures and ageing. and oxygen. food products.
properties. rough surfaces.

33
TO ORDER VACUUM CUPS
When ordering, it is possible to add the Vuototecnica code related to the desired compound for the item of the vacuum cup you
have chosen. This code can be found in the attached tables in the column “VT CODE”. If, for example, we want to order a traditional
vacuum cup Ø 85 mm in oil-resistant rubber, at the end of the item 01 85 10, which defines the shape of the vacuum cup, we simply
add the letter "A", relative to the oil-resistant rubber, which can be found in the technical table of the compounds. The code thus
obtained, 01 85 10 A, defines both the shape of the vacuum cup and the compound with which it is made. This code does not need
any other description.
To order the same vacuum cup in silicone, simply replace the letter "A" with the letter "S" relative to silicone and you will get code
01 85 10 S. All vacuum cups can be ordered by following this criterion.

VACUUM CUPS IN STOCK

The vacuum cups generally available in stock, are made of:

- Oil-resistant rubber "A”

- Benz oil-resistant rubber "B”
- Natural Para rubber "N”
- Silicone "S”

Vacuum cups made with different compounds, unless available in stock, are supplied only upon order and in minimum quantities,
to be defined according to their size.

CHOOSING VACUUM CUP HOLDERS

Our vacuum cup holders are divided into three large ranges:
- Mini vacuum cup holders
- Basic vacuum cup holders
- Special vacuum cup holders
These are in turn sub-divided according to their characteristics (with plunger valve, anti-rotation, with magnetic sensor, with built-in
shut-off valve, articulated, with double springing, etc.). The choice is left to the designer and will be made on the basis of the load
and the degree of automation of the handler to be made.
Further information is available on the catalogue pages relative to the vacuum cups.

CHOOSING A PUMP OR VACUUM GENERATOR

The calculation of the flow rate of the pump or vacuum generator is quite complex, since it requires the calculation of all the
negative volumes (air to be emptied contained in the vacuum cups, in the manifolds, in the pipes, up to the vacuum generator
or to the shut-off valve of the vacuum), a careful analysis of the load to be handled (permeability, roughness, irregularity of the
gripping surface, etc.), the evaluation of the required setting times and the vacuum values to be worked. To speed up calculation,
we decided to create a handbook indicating the flow rates required by the vacuum cups according to their diameter and that helps
size the pump or the vacuum generator based on their number, with fair approximation and safely. Two categories of materials
have been taken as a parameter: one impermeable (sheet metal and glass) and the other slightly porous and permeable (wood and
cardboard). The choice of the flow rate of the vacuum cups will be based on the nature of the material to be handled, more similar
to the parameter materials. The values indicated in the table are valid when:

- The level of vacuum available is no less than -75 Kpa

- The number of cycles per minute is less than 10
- The gripping surface is not particularly rough
- Permeability remains within acceptable values, such as the materials taken as examples

34
VACUUM CUP DIAMETER MATERIAL TO BE GRIPPED
Steel sheet and glass Wood and cardboard
mm m3/h m3/h
4 ÷ 10 0,15 0,30
11 ÷ 20 0,30 0,60
21 ÷ 35 0,50 1,00
36 ÷ 50 1,00 2,00
51 ÷ 85 1,50 3,00
86 ÷ 110 2,00 4,00
111 ÷ 200 2,50 5,00
201 ÷ 300 3,00 6,00
301 ÷ 360 4,00 8,00

Example:
Marble slab 2500 x 1200 x 50 mm Mass 420 kg

6 vacuum cups Ø 200 mm are required to handle the slab.

From the table, we can see that for gripping impermeable materials such as marble, the Ø 200 mm vacuum cups require 2.5 m3/h;
therefore, as there are 6 vacuum cups, the flow rate of the necessary vacuum pump will be:

6 x 2.5 = 15 m3/h

Note: The values shown in the table refer to the flow rate of rotary vane vacuum pumps. When vacuum generators based on the Venturi
principle are used, the value of the flow rates shown is doubled due to their lower suction efficiency.

COMPARISON BETWEEN PUMP item VTL5 AND VACUUM GENERATOR item 15 03 10 COMPARISON BETWEEN PUMP item RVP 40 AND VACUUM GENERATOR item PVP 40 M
VTL 5 Curve relative to the flow rate (referring to the suction pressure) RVP 40 Curve relative to the flow rate (referring to the suction pressure)
15 03 10 Curve relative to the flow rate (referring to the suction pressure) PVP 40 M Curve relative to the flow rate (referring to the suction pressure)

FLOW RATE FLOW RATE

m3/h m3/h

VACUUM VACUUM
mbar mbar

Therefore, for the same marble slab in the example shown above, the vacuum generator must be calculated as follows:

6 x 5 = 30 m3/h

35
CHOOSING CHECK VALVES, FILTERS, HOSES, SOLENOID VALVES AND
DISTRIBUTORS
All the accessories indicated in the title, necessary for construction of the system, must be chosen based on the suction connection
of the pump or vacuum generator. If, for example, the suction connection of the pump or the generator is G 1/2”, the check valve,
the suction filter, the hose, the vacuum interception solenoid valve and the distributor must have all G 1/2” connections. Vacuum
cup hoses, on the other hand, are already defined by the fitting installed on the vacuum cup holders or proportionate to their
support.

VACUUM CUPS BASED ON BERNOULLI’S THEOREM

There are numerous applications of Bernoulli's theorem: this theorem explains how air suction occurs in common gas burners, it
accounts for the operation of instruments such as the Venturi tube or the Pitot tube, used for measuring the speed of fluids.
It is possible to explain many phenomena with this theorem, such as the lifting of a plane’s wing or of a light disc in front of a tube
end from which air flows out quickly.
This last phenomenon, seemingly paradoxical, can be explained as follows: the air flowing between the disc with which the duct ends
and the sustained disc moves at a certain speed v and the pressure that reigns in this hollow space has a certain value P1.
As the air flows away from the centre of the hollow space, its speed decreases, finally reducing to stillness at a greater or lesser
distance, in an area where atmospheric pressure obviously reigns P0.
The air below the sustained disc is subjected to this same pressure P0.
In these conditions, disregarding the height h and indicating the density of the fluid with ρ and the acceleration of gravity with g,
the expression relative to the Bernoulli theorem is written:

P1 v2 P0
+ =
ρ g ρ

which clearly shows that P1 < P0.

This explains the subsistence of the disc, which is sucked from the hollow space with a force that overcomes the thrust exerted on
it by the air that flows from the tube, in addition to the weight of the disc.
This phenomenon is exploited for manufacturing vacuum gripping systems (vacuum cups) and handling, with no contact, fragile
objects, such as semiconductor plates, silica discs, solar cells, precious metal foils, films and whatever needs to be handled with
the greatest care.
Our cups based on Bernoulli’s principle are made with anodised aluminium, with stainless steel centre thrust disc.
The silicone rubber pins, located on the cup gripping plane, prevent transverse movements of the gripped object.

Further information on the vacuum accessories listed above can be found by consulting the catalogue on the pages relating to
each of them.

36
TECHNICAL MEMO
Unit of mass - Fundamental SI unit= Kilogram = Kg
(Avoid saying "weight" as the weight is the force deriving from the product of the mass due to the acceleration of local gravity).

Unit of acceleration (length / time 2 )

SI derived unit = metre per second squared = m/s 2

Unit of force = (mass x acceleration)

(The weight of a body is that particular force deriving from the product of its mass due to the acceleration of local gravity)
SI derived unit = newton = N = Kg · m/s 2
Other units:
Kilopond or kilogram-force = 1 Kp = 1 Kgf = 9.81 N

Unit of pressure and tension (force / area)

SI derived unit= pascal = 1 Pa = 1 N/m 2
(The pascal is a very small unit of measurement. In practice, we prefer to refer to the Megapascal or Kilopascal)

Megapascal 1 Mpa = 10 6 Pa = 1 MN/m 2 = 1 N/mm 2

Kilopascal 1 Kpa = 10 3 Pa = 1 KN/m 2

IP: DEGREE OF PROTECTION OF ENCLOSURES

The degrees of protection are expressed by two figures preceded by the abbreviation IP (International Protection). The first digit
indicates the protection against solids, the second digit the protection against liquids.

PROTECTION AGAINST SOLID BODIES PROTECTION AGAINST LIQUIDS

Protection against bodies larger than 52.5 mm.

1 Protection against accidental contact. 1 Protection against vertically dripping water.

Protection against bodies larger than 12.5 mm. Protection against water drops with max inclination
2 Protection against finger contact. 2 of 15°.

Protection against bodies larger than 2.5 mm. Rain protection, against water falling as a spray at
3 Protection against tool contact. 3 any angle up to 60°

Protection against bodies larger than 1 mm. Protection against water splashing from any
4 Protection against the ingress of cables. 4 direction.

Protection against the ingress of dust; a quantity

Protection against water spraying from any
5 that does not interfere with the satisfactory 5 direction.
operation of the equipment is tolerated.

6 Total protection against the ingress of dust. 6 Protection against waves or powerful water jets.

7 Protection against temporary immersion effects.

Protection against immersion effects for an

8 indefinite amount of time.

Derived from standards CEI 70-1 / IEC 144 / IEC 529 / UTE C 20-010 / DIN 40050

37
INDEX

1 VACUUM CUPS

2 VACUUM CUP HOLDERS

3 VACUUM MEASUREMENT, CONTROL AND ADJUSTMENT INSTRUMENTS

4 VACUUM VALVES AND SOLENOID VALVES

5 SUCTION FILTERS

6 VACUUM FITTINGS AND HOSES

7 VACUUM PUMPS AND PUMP SETS

8 VACUUM GENERATORS AND PNEUMATIC PUMP SETS

9 OCTOPUS VACUUM GRIPPING SYSTEM

10 GRAPHIC DIVISION

11 SPECIAL PRODUCTS
VACUUM CUPS

VACUUM CUPS WITH SUPPORTS PG. 1.01 ÷ 1.07

VACUUM CUPS WITH VULCANISED SUPPORT PG. 1.08 ÷ 1.10

3D drawings are available on vuototecnica.net

MAXIGRIP CUPS PG. 1.11
- ROUND FLAT AND BELLOWS VACUUM CUPS PG. 1.11
- FLAT AND BELLOWS ELLIPTICAL VACUUM CUPS PG. 1.12
- ADAPTERS FOR MAXIGRIP VACUUM CUPS PG. 1.13
- ACCESSORIES FOR MAXIGRIP VACUUM CUPS PG. 1.14
ROUND FLAT VACUUM CUPS WITH SUPPORTS PG. 1.15 ÷ 1.23
ROUND FLAT FOAM RUBBER VACUUM CUPS WITH SUPPORTS PG. 1.24 ÷ 1.26
VACUPREDATOR VACUUM CUPS FOR GRIPPING BAGS, PACKS AND FLEXIBLE CONTAINERS PG. 1.27 ÷ 1.28
ROUND FLAT VACUUM CUPS WITH VULCANISED SUPPORT FOR CLAMPING GLASS AND MARBLE PG. 1.29
FLAT ROUND VACUUM CUPS WITH VULCANISED SUPPORT PG. 1.30 ÷ 1.31
CIRCULAR RIM VACUUM CUPS WITH SUPPORTS PG. 1.32 ÷ 1.34
RECTANGULAR FLAT VACUUM CUPS WITH SUPPORTS PG. 1.35 ÷ 1.36
RECTANGULAR FLAT VACUUM CUPS WITH ANTI-SLIP SUPPORT PG. 1.37 ÷ 1.38
RECTANGULAR FLAT FOAM RUBBER VACUUM CUPS WITH SUPPORTS PG. 1.39 ÷ 1.40
1
RECTANGULAR FLAT VACUUM CUPS WITH VULCANISED SUPPORTS FOR CLAMPING GLASS AND MARBLE PG. 1.41
ELLIPTICAL FLAT VACUUM CUPS WITH SUPPORTS PG. 1.42 ÷ 1.43
ELLIPTICAL FLAT AND BELLOWS VACUUM CUPS WITH SUPPORTS PG. 1.44 ÷ 1.47
ELLIPTICAL VACUUM CUPS WITH VULCANISED SUPPORT PG. 1.48
CONCAVE VACUUM CUPS WITH VULCANISED SUPPORT PG. 1.49
FOAM RUBBER SHEETS AND STRIPS PG. 1.50
SB EXTRA SOFT FOAM RUBBER SHEETS PG. 1.51
NF NEOPRENE FOAM RUBBER SHEETS PG. 1.51
BELLOWS VACUUM CUPS WITH SUPPORTS FOR GRIPPING FLOW PACKS PG. 1.52
BELLOWS VACUUM CUPS WITH MALE AND FEMALE SUPPORTS PG. 1.53 ÷ 1.54
REINFORCED BELLOWS VACUUM CUPS WITH MALE AND FEMALE SUPPORTS PG. 1.55 ÷ 1.58
BELLOWS VACUUM CUPS FOR GLASS WITH SUPPORTS PG. 1.59
VACUUM CUPS WITH TWO BELLOWS FOR HEAVY-DUTY PACKAGING PG. 1.60 ÷ 1.63
VACUUM CUPS WITH ONE BELLOWS WITH VULCANISED SUPPORT PG. 1.64
VACUUM CUPS WITH TWO BELLOWS WITH VULCANISED SUPPORT PG. 1.65
BELLOWS VACUUM CUPS WITH VULCANISED SUPPORT PG. 1.66
PARTICULAR VACUUM CUPS WITH RELATIVE SUPPORTS PG. 1.67 ÷ 1.85
PARTICULAR BELLOWS VACUUM CUPS WITH SUPPORTS PG. 1.86 ÷ 1.105
SUPPORTS FOR VACUUM CUPS PG. 1.106 ÷ 1.129
GAS - NPT ADAPTERS PG. 1.130
THREADED GRUB SCREWS WITH CALIBRATED HOLE - ADAPTERS PG. 1.131
ADAPTERS FOR MAXIGRIP VACUUM CUPS PG. 1.132
SELF-LOCKING VACUUM CUPS WITH TRACTION RELEASE PG. 1.133 ÷ 1.134
BUILT-IN VACUUM CUPS WITH BALL VALVE PG. 1.135 ÷ 1.137
SPECIAL BUILT-IN VACUUM CUPS WITH BALL VALVE PG. 1.138 ÷ 1.141
SUPPORTS WITH RETRACTABLE STRIKING PIN PG. 1.142
ROUND VACUUM CUPS WITH SELF-LOCKING SUPPORT PG. 1.143
RECTANGULAR VACUUM CUPS WITH SELF-LOCKING SUPPORT PG. 1.144
ROUND VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT PG. 1.145
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT PG. 1.146
ROUND VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT PG. 1.147
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT PG. 1.148
ROUND VACUUM CUPS WITH BALL VALVE AND HIGH SELF-LOCKING SUPPORT PG. 1.149
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND HIGH SELF-LOCKING SUPPORT PG. 1.150
ROUND VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT, FOR GLASS PG. 1.151
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT, FOR GLASS PG. 1.152
ROUND VACUUM CUPS WITH BALL VALVE, SELF-LOCKING SUPPORT AND RELEASE BUTTON, FOR GLASS PG. 1.153 ÷ 1.154
ROUND VACUUM CUPS WITH BALL VALVE, SELF-LOCKING SUPPORT AND RELEASE BUTTON PG. 1.155
RECTANGULAR VACUUM CUPS WITH BALL VALVE, SELF-LOCKING SUPPORT AND RELEASE BUTTON PG. 1.156 ÷ 1.157
VACUUM CUPS BASED ON BERNOULLI’S THEOREM PG. 1.158 ÷ 1.160
VACUUM CUP QUESTIONNAIRE PG. 1.161 ÷ 1.162
1
3D drawings are available on vuototecnica.net
VACUUM CUPS WITH SUPPORTS

These traditional cup-shaped vacuum cups are

suited for gripping and handling small objects with
flat, slightly concave or convex surfaces.
This range of widely used cups has diameters

3D drawings are available on vuototecnica.net

ranging from 4 to 9 mm and are normally available
in standard compounds: natural para rubber N, oil-
resistant rubber A and silicone S.
They can be cold fitted with no adhesive onto a
nickel-plated brass support.
The support has been specially shaped to perfectly
fit with the vacuum cup and is equipped with a
male threaded pin to facilitate fastening to the
automation.
These cups are extremely easy to replace; simply
request the cup indicated in the table in the desired
compound when requesting the spare part.
Cups in special compounds, listed on
pg. 31, and supports in different materials can be
provided upon request in minimum quantities to be 1
defined in the order.

VACUUM CUPS
Force Volume A B D E F H
Item
Kg mm3 Ø Ø Ø
01 04 10 * 0.03 16 3 1.5 4 6.0 7.0 7.5
01 05 10 * 0.05 23 3 1.5 5 6.0 7.0 8.0
01 06 10 * 0.07 26 3 1.5 6 6.0 7.0 8.0
01 07 07 * 0.10 40 5 2.0 7 6.0 6.0 7.0
01 08 10 * 0.12 66 5 2.5 8 6.0 7.0 8.0
01 09 07 * 0.15 56 5 2.0 9 5.5 6.0 7.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
Hex. 7
A B D E F G H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 01 M5 7 2.90 3 5 10 18 brass 01 04 10 4
01 05 10
01 06 10
00 08 02 M5 7 4.75 3 5 10 18 brass 01 07 07 4
01 08 10
01 09 07

VACUUM CUP WITH SUPPORT

Hex. 7
Force A B D E F G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 04 10 * 0.03 M5 7 4 3 5 13.0 21.0 01 04 10 00 08 01 4
08 05 10 * 0.05 M5 7 5 3 5 13.5 21.5 01 05 10 00 08 01 4
08 06 10 * 0.07 M5 7 6 3 5 13.5 21.5 01 06 10 00 08 01 4
08 07 07 * 0.10 M5 7 7 3 5 13.5 21.5 01 07 07 00 08 02 4
08 08 10 * 0.12 M5 7 8 3 5 13.5 21.5 01 08 10 00 08 02 4
08 09 07 * 0.15 M5 7 9 3 5 12.5 20.5 01 09 07 00 08 02 4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.01
VACUUM CUPS WITH SUPPORTS

These traditional cup-shaped vacuum cups are suited for gripping and handling
objects with flat, slightly concave or convex surfaces.
This range of widely used cups has diameters ranging from 10 to 45 mm
and are normally available in standard compounds: natural para rubber N,
3D drawings are available on vuototecnica.net

oil-resistant rubber A and silicone S.

They can be cold fitted with no adhesive onto a nickel-plated brass or
anodised aluminium support.
The support has been specially shaped to perfectly fit with
the vacuum cup and is equipped with a male threaded pin to
facilitate fastening to the automation.
These cups are extremely easy to replace; simply request the
cup indicated in the table in the desired compound when
requesting the spare part.
Cups in special compounds, listed on pg. 31, and supports
in different materials can be provided upon specific
request in minimum quantities to be defined in the order.

1
VACUUM CUPS
Force Volume A B D E F H
Item
Kg mm3 Ø Ø Ø
01 10 10 * 0.19 227 7 4.0 10 8.5 8.5 11.0
01 12 10 * 0.28 254 8 4.0 12 8.0 9.0 11.0
01 15 10 * 0.44 364 8 4.0 15 8.0 9.5 12.0
01 18 10 * 0.63 502 8 4.0 18 8.0 9.5 12.0
01 20 10 * 0.78 536 8 4.0 20 8.0 9.5 12.0
01 22 10 * 0.95 723 8 4.0 22 8.0 10.0 13.0
01 25 15 * 1.23 1628 12 6.0 25 10.0 11.5 16.0
01 30 15 * 1.76 2055 12 6.0 30 10.0 12.5 17.0
01 35 15 * 2.40 3292 15 10.0 35 10.0 11.5 16.0
01 40 15 * 3.14 4740 15 10.0 40 10.0 12.5 18.0
01 45 15 * 3.98 8553 15 10.0 45 10.0 14.5 23.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
A D E F G H T Support For vacuum cup Weight
Item
Ø Ø material item g
Hex. T
00 08 03 G1/8” 5.5 5 8 7.0 20.0 12 brass 01 10 10 9
01 12 10
01 15 10
01 18 10
01 20 10
01 22 10
00 08 05 G1/8” 7.5 5 8 9.5 22.5 12 brass 01 25 15 10
01 30 15
00 08 20 G1/4” 12.0 8 14 10.0 32.0 17 aluminium 01 35 15 11
01 40 15
01 45 15

VACUUM CUPS WITH SUPPORT

Force A D E F G H T Vacuum cup Support Weight
Item
Kg Ø Ø item item g Hex. T
08 10 10 * 0.19 G1/8” 10 5 8 11 24 12 01 10 10 00 08 03 9.0
08 12 10 * 0.28 G1/8” 12 5 8 11 24 12 01 12 10 00 08 03 9.6
08 15 10 * 0.44 G1/8” 15 5 8 12 25 12 01 15 10 00 08 03 9.7
08 18 10 * 0.63 G1/8” 18 5 8 12 25 12 01 18 10 00 08 03 9.7
08 20 10 * 0.78 G1/8” 20 5 8 12 25 12 01 20 10 00 08 03 9.8
08 22 10 * 0.95 G1/8” 22 5 8 13 26 12 01 22 10 00 08 03 10.2
08 25 15 * 1.23 G1/8” 25 5 8 16 29 12 01 25 15 00 08 05 12.0
08 30 15 * 1.76 G1/8” 30 5 8 17 30 12 01 30 15 00 08 05 12.7
08 35 15 * 2.40 G1/4” 35 8 14 16 38 17 01 35 15 00 08 20 13.6
08 40 15 * 3.14 G1/4” 40 8 14 18 40 17 01 40 15 00 08 20 14.1
08 45 15 * 3.98 G1/4” 45 8 14 23 45 17 01 45 15 00 08 20 17.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.02
VACUUM CUPS WITH SUPPORTS

These traditional cup-shaped vacuum cups are suited for gripping

and handling objects with flat, slightly concave or convex
surfaces.
This range of widely used cups has diameters ranging from 10

gripping and handling objects with flat, slightly concave or
convex surfaces.
These widely used vacuum cups have a diameter of 85 mm and
3D drawings are available on vuototecnica.net

are normally available in standard compounds: natural para

rubber N, oil-resistant rubber A and silicone S.
They can be cold fitted with no adhesive onto an anodised
aluminium support.
The support has been specially shaped to perfectly fit with
the vacuum cup and is equipped with a male threaded pin to
facilitate fastening to the automation. Moreover, they have a M8
threaded hole for any necessary insertion of a grub screw with
calibrated hole (see pg. 1.131), having the function of reducing
the quantity of air to be suctioned.
These cups are extremely easy to replace; simply request
the cup indicated in the table in the desired compound when
requesting the spare part.
Cups in special compounds, listed on pg. 31, and supports in
1 different materials can be provided upon specific request in
minimum quantities to be defined in the order.

VACUUM CUPS
Force Volume A B C D E G H I
Item
Kg cm3 Ø Ø Ø Ø
01 85 10 * 14.18 54.8 25 15 25 85 16 23 41 4.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
A D Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 28 G1/4” 25 aluminium 01 85 10 13.4
00 08 136 G1/8” 25 aluminium 01 85 10 9.2
00 08 91 M10x1,25 25 brass 01 85 10 38.4

VACUUM CUPS WITH SUPPORT

Force A D Vacuum cup Support Weight
Item
Kg Ø Ø item item g
08 85 10 * 14.18 G1/4” 85 01 85 10 00 08 28 49.3
08 85 12 * 14.18 G1/8” 85 01 85 10 00 08 136 45.1
08 85 13 * 14.18 M10x1,25 85 01 85 10 00 08 91 73.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

These traditional cup-shaped vacuum cups are suited for

gripping and handling objects with flat, slightly concave or
convex surfaces.
These widely used vacuum cups have a diameter of 85 mm

3D drawings are available on vuototecnica.net

and are normally available in standard compounds: natural
para rubber N, oil-resistant rubber A and silicone S.
They can be cold fitted with no adhesive onto an anodised
aluminium support.
The support has been specially shaped to perfectly fit with the
vacuum cup and is equipped with a female threaded pin to
facilitate fastening to the automation.
These cups are extremely easy to replace; simply request
the cup indicated in the table in the desired compound when
requesting the spare part.
Cups in special compounds, listed on pg. 31, and supports in
different materials can be provided upon specific request in
minimum quantities to be defined in the order.

VACUUM CUPS
Force Volume A B C D F G H I
Item
Kg cm3 Ø Ø Ø Ø
01 85 10 * 14.18 54.8 25 15 25 85 16 23 41 4.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
A B Support For Vacuum cup Weight
Item
Ø Ø material item g
00 08 29 15.5 M12 aluminium 01 85 10 6.6
00 08 46 15.5 G1/4” aluminium 01 85 10 6.5

VACUUM CUPS WITH SUPPORT

Force A D H Vacuum cup Support Weight
Item
Kg Ø Ø item item g
08 85 25 * 14.18 G1/4” 85 41 01 85 10 00 08 46 42.4
08 85 26 * 14.18 M12 85 41 01 85 10 00 08 29 42.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

This range of rather sturdy and deep cups

is designed to handle bodywork parts and
components in moulded steel sheet.
These cups are produced with a special compound
3D drawings are available on vuototecnica.net

called BENZ, which can withstand heavy-duty work

and the chlorine usually contained in the oil used for
moulding and drawing of steel sheets.
The galvanised steel support is vulcanised onto the
cup. Galvanised steel adapters are also available in
order to modify the suction connection from M10 to
gas threading.
Cups in other special compounds, listed on pg.
31 can be provided upon request in minimum
quantities to be defined in the order.

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume D E F G H Support Weight
Item
Kg cm3 Ø material g
08 30 38 B 1.80 3.1 30 20 17 10 37 steel 20.8
08 40 41 B 3.20 6.4 40 23 18 12 41 steel 24.9
08 40 41 N 3.20 6.4 40 23 18 12 41 steel 24.9
Compound: B= BENZ rubber; N= natural para rubber

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A F H Support Weight
Item
Kg cm3 Ø material g
08 60 45 B 7.10 25.9 M10 18 44 steel 29.5
08 60 45 1/4” B 7.10 25.9 G1/4” 10 44 steel 29.5
Compound: B= BENZ rubber

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume E F G H Support Weight
Item
Kg cm3 material g
08 80 50 B 12.60 41.2 33 12.5 26 51 steel 58.0
Compound: B= BENZ rubber

ADAPTERS
D d H Support Weight
Item
Ø Ø material g
00 08 130 G1/4” M10 14 steel 04.9
00 08 131 G3/8” M10 14 steel 12.8

These cups are specially designed for gripping

moulded or drawn sheet metal and are largely used
in the automotive sector.
Their ground lip allows an immediate gripping of

3D drawings are available on vuototecnica.net

the load even at the slightest resting pressure and
ensures perfect vacuum seal.
These cups are produced in a special compound
called BENZ, able to withstand the chlorine usually
contained in the oils used for moulding and drawing
the steel sheets.
The galvanised steel support is is vulcanised onto
the cup.
The cups can be provided upon request in minimum
quantities in natural para rubber, in silicone or in
special compounds, listed on pg. 31.

VACUUM CUPS WITH MALE VULCANISED SUPPORT

Force Volume A B C D E F G H Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material g
08 50 40 * 04.90 10.3 31 G3/8” -- 50 16.0 12 06.5 29.0 steel 38.5
08 50 40 GR B 04.90 10.3 31 G3/8” G1/8” 50 16.0 -- 06.5 29.0 steel 38.5
08 75 40 * 11.04 29.3 31 G3/8” -- 75 25.0 12 09.0 38.0 steel 57.9
C Housing for
08 75 40 GR B 11.04 29.3 31 G3/8” G1/8” 75 25.0 -- 09.0 38.0 steel 57.9 threaded grub
08 75 40 GR N 11.04 29.3 31 G3/8” G1/8” 75 25.0 -- 09.0 38.0 steel 57.9 screws

08 100 40 * 19.62 42.6 32 G3/8” -- 100 26.0 12 09.0 39.0 steel 78.3
08 100 50 * 19.62 70.6 32 G3/8” -- 100 30.5 12 15.0 43.5 steel 74.8
08 50 40 1/4” B 04.90 10.3 31 G1/4” -- 50 16.0 -- 06.5 29.0 steel 37.4
08 75 40 1/4” B 11.04 29.3 31 G1/4” -- 75 25.0 -- 09.0 38.0 steel 57.6
08 100 40 1/4” B 19.62 42.6 32 G1/4” -- 100 26.0 -- 09.0 39.0 steel 76.8
08 50 40 M10 B 04.90 10.3 31 M10 -- 50 16.0 -- 06.5 29.0 steel 32.7
08 100 50 M10 B 19.62 70.6 32 M10 -- 100 30.5 -- 15.0 43.5 steel 70.2
08 75 40 M14 B 11.04 29.3 31 M14 x 1.5 -- 75 25.0 -- 09.0 38.0 steel 54.9
08 100 50 M14 B 19.62 70.6 32 M14 x 1.5 -- 100 30.5 -- 15.0 43.5 steel 74.9
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone

THREADED GRUB SCREWS WITH CALIBRATED HOLE

A D F H Grub screw Weight
Item
Ø Ø material g
00 08 164 G1/8” 1.2 5 7 brass 3.0
00 08 165 G1/8” 1.5 5 10 brass 3.0
00 08 334 G1/8” 3.0 4 7 brass 4.0
Threaded grub screws with calibrated hole, for vacuum cups with extension GR.

VACUUM CUPS WITH FEMALE VULCANISED SUPPORT

Force Volume A B D E G H Support Weight
Item
Kg cm3 Ø Ø Ø material g
08 50 40 F B 04.90 10.3 31 G3/8” 50 16.0 06.5 32.5 steel 49.5
08 75 40 F B 11.04 29.3 31 G3/8” 75 25.0 09.0 41.5 steel 68.3 Sp19
08 75 40 F S 11.04 29.3 31 G3/8” 75 25.0 09.0 41.5 steel 68.3
08 100 40 F B 19.62 42.6 32 G3/8” 100 26.0 09.0 42.5 steel 89.3
08 100 40 F S 19.62 42.6 32 G3/8” 100 26.0 09.0 42.5 steel 89.3
08 100 50 F B 19.62 70.6 32 G3/8” 100 30.5 15.0 47.0 steel 88.8
08 100 50 F S 19.62 70.6 32 G3/8” 100 30.5 15.0 47.0 steel 88.8
Compound: B= BENZ rubber; S = silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.09
VACUUM CUPS WITH
VULCANISED SUPPORT
These vacuum cups are very similar to those
described on the previous page: they differ only for
their round lip and their internal cleats.
These features allow them to be used even in the
3D drawings are available on vuototecnica.net

most heavy-duty conditions.

The field of use is the same.
They are also made with BENZ compound and the
galvanised steel support is vulcanised onto the cup.
Also these cups can be provided upon request
in minimum quantities and in other special
compounds, listed on pg. 31, to be defined in the
order.

VACUUM CUPS WITH MALE VULCANISED SUPPORT

Force Volume A B D E G H Support Weight
Item
Kg cm3 Ø Ø Ø material g
08 50 99 B 04.90 10.3 30 G3/8” 50 23.5 9 36.5 steel 043.2
08 75 99 B 11.04 29.3 35 G3/8” 75 23.5 9 36.5 steel 059.2
08 100 99 B 19.62 42.6 35 G3/8” 100 40.0 12 53.0 steel 113.2
08 100 99 N 19.62 42.6 35 G3/8” 100 40.0 12 53.0 steel 113.2
08 50 99 1/4” B 04.90 10.3 30 G1/4” 50 23.5 9 36.5 steel 039.4
08 75 99 1/4” B 11.04 29.3 35 G1/4” 75 23.5 9 36.5 steel 055.2
08 100 99 1/4” B 19.62 42.6 35 G1/4” 100 40.0 12 53.0 steel 109.2
Compound: B= BENZ rubber; N= natural para rubber

VACUUM CUPS WITH FEMALE VULCANISED SUPPORT

Force Volume A B D E G H Support Weight
Item
Kg cm3 Ø Ø Ø material g
08 50 99 F B 04.90 10.3 31 G3/8” 50 23.5 9 40.0 steel 055.6 Sp19
08 50 99 F S 04.90 10.3 31 G3/8” 50 23.5 9 40.0 steel 055.6
08 75 99 F B 11.04 29.3 35 G3/8” 75 23.5 9 40.0 steel 070.5
08 75 99 F S 11.04 29.3 35 G3/8” 75 23.5 9 40.0 steel 070.5
08 100 99 F B 19.62 42.6 35 G3/8” 100 40.0 12 56.5 steel 118.8
Compound: B= BENZ rubber; S = silicone

These vacuum cups have been created as an alternative to the ordinary cups used
in the robot-automotive field. They offer an excellent solution to gripping and
handling problems that could arise on vacuum-driven handlers in every
industry sector.

3D drawings are available on vuototecnica.net

They can be both round and oval, flat and bellows-type, and equipped
with support. The extremely flexible outside lip, which can be
associated with the typical features of the bellows cups, helps them
adapt on flat, concave and convex surfaces with no risk of deforming or
breaking even the thinnest objects to be handled.
The innovative design of the inside of the cups, which facilitates the
drainage of oil and water, ensures a high friction coefficient with
the gripping surface and, in particular, a unique grip on oil-covered
metal sheets or wet glass or marble sheets. This particular feature
guarantees a firm grip and, therefore, accurate placement of the load
to be handled.
MAXIGRIP standard vacuum cups are made with our exclusive BENZ compound:
- Hardness 60-75°Sh.
- Working temperature between -40 and +170°C
- Stain-resistant 1
- Excellent resistance to abrasion, water and to oils containing chlorine.
Their support is vulcanised onto the cup. A wide range of accessories, such as
adapters, couplers and articulated joints, allows them to be installed on any
vacuum-driven handler.
These cups can also be provided in the special compounds listed on pg. 31, thanks
to their universality of use.

ROUND FLAT AND BELLOWS VACUUM CUPS

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B Sp D d E F G H I SW Support Weight
Item
Kg cm3 Ø Ø Ø Ø material g
VRP 40 A* 03.14 03.7 26 G1/4” 15 040 17 16 14 04.0 31 15 6 aluminium 033.6
Sp
VRP 50 A* 04.90 07.4 30 G3/8” 19 050 21 18 14 05.0 33 15 6 aluminium 049.3
VRP 60 A* 07.06 13.9 30 G3/8” 19 060 21 21 14 06.0 36 15 6 aluminium 055.3
VRP 80 A* 12.56 29.6 35 G3/8” 19 080 21 25 14 07.5 40 15 6 aluminium 074.9
VRP 100 A* 19.62 51.6 35 G3/8” 19 100 21 25 14 09.5 40 15 6 aluminium 080.7
VRP 125 A* 30.66 96.5 35 G3/8” 19 125 21 33 14 12.5 48 15 6 aluminium 139.6
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone
Note: Can be supplied with NPT threading for minimum quantities of 100 pieces per item.
Ordering example: VRP 80 A NPT B

BELLOWS VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C Sp D d E F G H I M Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø Ø material g Sp

VRS 40* 03.14 009.7 043 030 G1/4” 17 040 024 21.0 10 07.0 35.0 14 G1/8” steel 056.3
VRS 50* 04.90 015.6 053 040 G3/8” 22 050 034 21.0 10 07.0 36.0 15 G1/4” steel 077.6
VRS 60* 07.06 022.8 063 050 G3/8” 22 060 044 21.0 10 07.0 36.0 15 G1/4” steel 107.9
VRS 80* 12.56 047.3 083 070 G3/8” 22 080 064 23.0 10 09.0 38.0 15 G1/4” steel 205.9
VRS 100* 19.62 104.2 103 080 G3/8” 22 100 079 29.0 10 13.0 44.0 15 G1/4” steel 269.0
VRS 125* 30.66 202.5 128 105 G3/8” 22 125 100 32.5 10 16.5 47.5 15 G1/4” steel 464.2
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone
Note: Height "C" available with NPT threading. Ordering example: VRS 80 NPT B

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.11
FLAT AND BELLOWS ELLIPTICAL VACUUM CUPS
3D drawings are available on vuototecnica.net

1 Sp

ELLIPTICAL VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C Sp D E F G H I L M Support Weight
Item
Kg cm3 Ø Ø material g
VEP 30 60 * 04.01 04.5 047 17 G1/4” 17 060 13 10 3 27 14 30 G1/8” steel 042.6
VEP 30 90 * 06.26 07.0 077 17 G1/4” 17 090 13 10 3 27 14 30 G1/8” steel 063.5
VEP 40 80 * 07.14 13.2 070 30 G1/4” 17 080 14 10 4 28 14 40 G1/8” steel 068.0
VEP 50 100 * 11.15 15.0 080 30 G3/8” 22 100 16 10 5 31 15 50 G1/4” steel 110.0
VEP 60 120 * 16.06 32.1 095 35 G3/8” 22 120 18 10 6 33 15 60 G1/4” steel 156.1
VEP 70 140 * 21.86 53.5 110 40 G3/8” 22 140 19 10 7 34 15 70 G1/4’’ steel 199.4
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone
Note: Height "C" available with NPT threading. Ordering example: VEP 40 80 NPT B

BELLOWS ELLIPTICAL VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C Sp D E F G H K I L M N O Support Weight
Item
Kg cm3 Ø Ø material g
VES 30 60 * 04.01 012.6 050 20 G1/4” 17 060 21 10 07.0 35 063 14 33 G1/8” 30 044.5 steel 049.5
VES 40 80 * 07.14 024.8 070 30 G1/4” 17 080 23 10 09.0 37 083 14 43 G1/8” 40 064.0 steel 091.9
VES 50 100 * 11.15 057.6 080 30 G3/8” 22 100 29 10 13.0 44 103 15 53 G1/4” 50 079.0 steel 125.3
VES 70 140 * 21.86 122.8 110 40 G3/8” 22 140 33 10 16.5 48 143 15 73 G1/4” 70 109.0 steel 227.8
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone
Note: Height "C" available with NPT threading. Ordering example: VES 40 80 NPT B

These standard accessories provide various

MAXIGRIP CUP assembly options.
The galvanised steel adapters transform the female
standard support thread connections into male and

3D drawings are available on vuototecnica.net

the gas ones into metric.
The internal hexagonal housing allows for an easy
screwing on the supports.

MF ADAPTER FOR VRP VACUUM CUPS

D d F H SW Weight
Item
Ø Ø g
0O 08 215 G3/8” G1/4” 8 14 6 11.5

MF ADAPTER FOR VRS - VEP - VES VACUUM CUPS

D d F H SW Weight
Item
Ø Ø g
00 08 216 G3/8” G1/4” 8 11.5 6 6.0

MM ADAPTER FOR VRP VACUUM CUPS

D d E F SW Weight
Item
Ø Ø g
00 08 217 G1/4” G1/4” 15 10 6 16.7
00 08 218 G1/4” M10 x 1.5 15 12 6 10.2
00 08 219 G1/4” M14 x 1.5 15 12 6 16.0
00 08 220 G3/8” G1/4” 14 10 6 18.4
00 08 221 G3/8” M10 x 1.5 14 12 6 16.3
00 08 222 G3/8” M14 x 1.5 14 12 6 22.5

MM ADAPTER FOR VRS - VEP - VES VACUUM CUPS

D d E F SW Weight
Item
Ø Ø g
00 08 223 G1/4” G1/4” 11.5 10 6 13.9
00 08 224 G1/4” M10 x 1.5 13.0 12 6 10.1
00 08 225 G1/4” M14 x 1.5 13.0 12 6 15.8
00 08 226 G3/8” G1/4” 10.5 11 6 16.6
00 08 227 G3/8” M10 x 1.5 10.5 13 6 14.2
00 08 228 G3/8” M14 x 1.5 10.5 13 6 20.2

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.13
ACCESSORIES FOR MAXIGRIP VACUUM CUPS

The accessories shown on this page are suitable for

the previously described MAXIGRIP CUPS.
MF adapters are suitable for increasing female
connections of 1/8 "and 1/4" gas threaded
3D drawings are available on vuototecnica.net

connection vacuum cups to a larger size, still

female, of 1/4” or 3/8" with gas or NPT threading,
upon request.
Those that are galvanised steel and with gas
threading and those with NPT threading are made
of aluminium.
AQ adapters with square flange and male or female
threaded connections made of anodised aluminium
are suitable for robotic gripping systems to allow
for quick installation of vacuum cups on the special
profiles, used in the AUTOMOTIVE sector. The built-
in seal guarantees perfect vacuum seal.

MF ADAPTER FOR VRP-VRS-VEP-VES VACUUM CUPS

Sp
E F D d Sp Adapter Weight
Item
Ø Ø material g
00 08 207 14 10 G1/8” G1/4” 17 aluminium 17.6
00 08 208 15 010 G1/4” G3/8” 22 aluminium 31.0
00 08 329 17 012 G1/8” 1/4” NPT 17 steel 17.6
00 08 328 22 016 G1/4” 3/8” NPT 22 steel 31.0

SQUARE ADAPTER FOR VRP-VRS-VEP-VES VACUUM CUPS

H E F D d Material Weight O-ring
Item spare part
Ø Ø g item
AQ 32 1/8” 13 4.6 8.4 G1/8” 5 aluminium 11.8 00 08 214
AQ 32 1/4” 13 4.6 8.4 G1/4” 5 aluminium 13.2 00 08 214
AQ 32 3/8” 13 4.6 8.4 G3/8” 5 aluminium 15.6 00 08 214
AQ 32 1/2” 13 4.6 8.4 G1/2” 5 aluminium 17.2 00 08 214

SQUARE ADAPTER FOR VRP-VRS-VEP-VES VACUUM CUPS

H E F D d Material Weight O-ring
Item spare part
Ø Ø g item
AQS 32 1/8” 16.1 4.6 11.5 G1/8” 5 aluminium 12.2 00 08 214
AQS 32 1/4” 20.0 4.6 15.4 G1/4” 5 aluminium 13.6 00 08 214
AQS 32 3/8” 20.0 4.6 15.4 G3/8” 5 aluminium 16.2 00 08 214
AQS 32 1/2” 20.0 4.6 15.4 G1/2” 5 aluminium 17.8 00 08 214

SQUARE ADAPTER FOR VRP-VRS-VEP-VES VACUUM CUPS

H E F D d Material Weight O-ring
Item spare part
Ø Ø g item
AQ 32 1/4” F 17.9 4.6 13.3 G1/4” 11 aluminium 15.2 00 08 214
AQ 32 3/8” F 17.9 4.6 13.3 G3/8” 11 aluminium 14.1 00 08 214

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.14
ROUND FLAT VACUUM CUPS WITH SUPPORTS

The cups described on this page have been designed to solve most of
the gripping problems that can arise handling wooden or plastic panels,
thin glass or marble sheets, fragile metal sheets, ceramic or baked clay
tiles, etc.

3D drawings are available on vuototecnica.net

Their low, strong and slightly tilted lip does not swipe on the loading
surface during the gripping phase.
The cleats on the inside of these cups, along with reducing the
volume of air to be sucked, create a perfect supporting surface which
prevents any gripping surface deformation as well as vertically lifted
loads from slipping. These cups can be cold fitted with no adhesives
onto their anodised aluminium support and locked by the ring nut. These
cups are extremely easy to replace; simply request the cup indicated in
the table in the desired compound when requesting the spare part.

VACUUM CUPS
Force Volume A B C D F G H M
Item 1
Kg cm3 Ø Ø Ø Ø Ø
01 76 24 * 11.33 15.8 54 35 16 76 4.5 10 24 36
01 90 24 * 15.89 19.5 64 35 16 90 4.5 10 24 36
01 110 24 * 23.74 27.2 79 35 16 110 4.5 10 24 36
01 150 36 * 45.00 75.8 98 70 16 150 6.0 17 36 70
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Ring nut Support

SUPPORTS
A C D E F G H I Support/ring nut For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 108 G1/4” 34 35 9 19.5 4.5 33.0 4.5 aluminium 01 76 24 31.2
01 90 24
01 110 24
00 08 110 G3/8” 34 35 9 19.5 4.5 33.0 4.5 aluminium 01 76 24 33.7
01 90 24
01 110 24
00 08 112 G3/8” 69 69 15 22.0 5.5 42.5 6.0 aluminium 01 150 36 132.1
Note: the ring nut is provided automatically when the support is ordered with its own item

VACUUM CUP WITH SUPPORT

Force A D E F H Vacuum cup Support Weight
Item
Kg Ø Ø item item g
08 76 24 1/4” * 11.33 G1/4” 76 24 14 38 01 76 24 00 08 108 83.1
08 90 24 1/4” * 15.89 G1/4” 90 24 14 38 01 90 24 00 08 108 112.0
08 110 24 1/4” * 23.74 G1/4” 110 24 14 38 01 110 24 00 08 108 168.2
08 76 24 3/8” * 11.33 G3/8” 76 24 14 38 01 76 24 00 08 110 85.6
08 90 24 3/8” * 15.89 G3/8” 90 24 14 38 01 90 24 00 08 110 114.5
08 110 24 3/8” * 23.74 G3/8” 110 24 14 38 01 110 24 00 08 110 170.7
08 150 36 * 45.00 G3/8” 150 36 14 50 01 150 36 00 08 112 436.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.15
ROUND FLAT VACUUM CUP WITH SUPPORT

The cups described on this page have been

designed for gripping soft drink cans. They can
obviously be also used for gripping other objects
with flat smooth or slightly rough surfaces.
3D drawings are available on vuototecnica.net

The shape of its lip allows a firm grip of the surface

of the load to be handled, eliminating any oscillation
and reducing the air volume contained within, thus
allowing quicker grip and release.
These cups can be cold fitted with no adhesives
onto their anodised aluminium support equipped
with a threaded hole in the centre to allow their
fastening to the automation.
This cup is extremely easy to replace; simply
request the cup indicated in the table in the desired
compound when requesting the spare part.

VACUUM CUP
Force Volume A B C D F H
Item
Kg cm3 Ø Ø Ø Ø
01 56 15 * 6.15 7.1 56 48 44 56 11 15
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORT
A B C D F H Support For vacuum cup Weight
Item
Ø Ø Ø Ø material item g
00 08 83 48.5 M12 5 48.5 11 14.5 aluminium 01 56 15 67.4

VACUUM CUP WITH SUPPORT

Force A B C D F H Vacuum cup Support Weight
Item
Kg Ø Ø Ø Ø item item g
08 56 15 * 6.15 48.5 M12 5 56 11 18 01 56 15 00 08 83 78
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

These cups feature a particularly thin and soft lip, which

allows it to grip very rough surfaces. Its supporting surface
with cleats guarantees a firm grip on the load to be handled.
These cups have been specially designed for gripping

3D drawings are available on vuototecnica.net

SUPPORT
A B C D H M Support For vacuum cup Weight
Item
Ø Ø Ø Ø material item Kg
00 08 37 180 M12 G3/8” 206 12 70 aluminium 01 220 10 A 0.95

NBR rubber

VACUUM CUP WITH SUPPORT

Force A B D H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item Kg
08 220 10 A 78.5 180 180 220 20 00 08 37 01 220 10 A 1.12

3D drawings are available on vuototecnica.net

VACUUM CUP
Force Volume A B C D E F H N
Item
Kg cm3 Ø Ø Ø Ø Ø
01 250 20 * 122.60 200.0 235 227 220 254 4 11 23 220
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORT
A B C D E H M For vacuum cup Support Weight
Item
Ø Ø Ø Ø item material Kg
00 08 115 223 M12 G3/8” 230 4 15 70 01 250 20 aluminium 1.65

VACUUM CUP WITH SUPPORT

Force A B C D F H M Vacuum cup Support Weight
Item
Kg Ø Ø Ø Ø item item Kg
08 250 20 * 122.60 237 M12 G3/8” 254 15 23 70 01 250 20 00 08 115 1.78
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.23
ROUND FLAT FOAM RUBBER VACUUM CUPS WITH SUPPORTS

These foam rubber cups are made with a special compound called GERANIUM, with a
density that allows them to grip even uneven and very rough surfaces maintaining their
elasticity also after many working cycles. They are provided with self-adhesive side for
a quick fixing to their support. This series of cups has been designed for handling loads
3D drawings are available on vuototecnica.net

Force A B D H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item Kg
08 220 10 OF 63.6 180 180 220 35 01 220 10 OF 00 08 37 0.98
08 220 10 NF 63.6 180 180 220 35 01 220 10 NF 00 08 37 0.97

For the gripping of bags, packs and flexible containers in paper

or plastic, containing powders, granulated products, loose or
liquid products. These new vacuum cups have been designed and
manufactured to safely grip even the most difficult and irregular

3D drawings are available on vuototecnica.net

packages. Made of anodised aluminium and equipped with a slotted
plate inside them to allow flexible containers to perfectly adapt to the
cup, as well as a special foam rubber seal which, following the inevitable
creases that form on flexible containers during gripping, prevents
perimeter vacuum losses.
They are especially suitable for gripping flow packs, flexible containers
for intravenous therapy, bags of sweets or other similar products, plastic
bags of granulated products, of cement, sugar or flour, etc.
The lifting force was calculated considering a level of vacuum of at least
-75 Kpa, the total surface enclosed within the seal and a factor of safety 3.

Slotted plate
Slotted plate
Air inlet connection (F)
Support
Support
Fastenings for Cap
the automation Cap

Spacers
Spacers
Vacuum Effective
connection Effective
gripping area (T)
gripping area (T) Cap
Cap

Foam rubber
Nitrile rubber combined
with foam rubber

ROUND VACUPREDATOR VACUUM CUPS

Force A B C F G H I L M N O P R S T Weight
Item
Kg Ø Ø Ø Ø Ø Ø Ø Kg
VP 12 OF 10 15 17.5 134 89 70 G1/8” M8 G1/2” G1/8” 70 49 10 28 15 13 17.5 92 0.54
VP 22 OF 15 15 63.6 220 165 110 G1/4” M12 G1” G1/8” 120 78 15 52 15 20 20.0 180 1.55

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.27
VACUPREDATOR VACUUM CUPS FOR GRIPPING BAGS,
PACKS AND FLEXIBLE CONTAINERS
3D drawings are available on vuototecnica.net

Air inlet connection (F)

1
Slotted plate
Support

Cap
Fastenings for
the automation

Spacers

Cap
Vacuum Effective
connection gripping area (T)

Foam rubber

ELLIPTICAL VACUPREDATOR VACUUM CUPS

Force A B C C1 D E F G H I L M N O P R S T Weight
Item
Kg Ø Ø Ø Ø Kg
VP 06 12 OF 10 15 9.4 60 40 --- --- 120 111 --- M8 G3/8” --- 100 49 10 29 15 14 10 40 x 100 0.36
VP 09 16 OF 10 30 17.9 90 60 --- 80 160 145 G1/4” M8 G1/2” G1/8” 130 63 10 25 30 18 15 60 x 130 0.63
VP 09 21 OF 10 30 27.4 95 60 --- 80 210 185 G1/4” M12 G1/2” G1/8” 160 63 10 25 30 18 15 65 x 180 0.80
VP 15 20 OF 10 30 43.8 150 120 95 --- 200 175 G3/8” M12 G1” G1/8” 160 63 10 25 30 18 15 120 x 170 1.10
VP 20 30 OF 15 30 82.5 200 150 115 --- 300 250 G3/8” M12 G1” G1/8” 200 78 15 40 30 20 25 150 x 250 2.24
VP 30 40 OF 15 30 174.4 300 250 160 --- 400 350 G3/8” M12 G2” G1/8” 300 78 15 40 30 20 30 240 x 340 3.85

CODING EXAMPLE:

Model: Foam rubber (P) height:

Vacu Predator for VP0612-VP0916-VP0921-VP12-VP22
15-20-25-30 mm

Dimensions: for VP1520-VP2030-VP3040

06 12 ( 60 x 120 mm ) 20-25-30-40 mm
09 16 ( 90 x 160 mm )
09 21 ( 95 x 210 mm ) Spacer (N) height:
15 20 ( 150 x 200 mm ) 5 mm
20 30 ( 200 x 300 mm ) 10 mm
30 40 ( 300 x 400 mm ) 15 mm
12 ( ø 134 mm )
22 ( ø 220 mm )
Type of Foam
Rubber compound:
OF: ORANGE FOAM
SB: EXTRA SOFT
NF: NEOPRENE
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.28
FLAT ROUND VACUUM CUPS WITH VULCANISED SUPPORT,
FOR CLAMPING GLASS AND MARBLE
Glass and marble manufacturers’ machining centres require increasingly
accurate and safe clamping systems. This has led us to creating this new
series of cups.
They are vulcanised onto a steel support and are provided with a hole in the

3D drawings are available on vuototecnica.net

centre for vacuum connection or for a ball valve, as well as with 3-4 holes on
the internal circumference for housing Allen screws.
Their extremely flexible lip allows them to easily adapt to the sheets to be
held, with no risk of deformation or rupture, even for the thinnest ones.
The particular shape of the internal support plane of these cups ensures
a high friction coefficient with the gripping surface and especially a
considerable grip on wet glass and marble sheets, thanks to the water
drainage. All this guarantees a firm, safe grip.
Furthermore, these cups feature the highest accuracy of their
thickness, whose nominal height has a tolerance of only five
hundredths of millimetre.
They are normally produced with oil-resistant rubber A, but they can
be ordered in other compounds, listed on pg. 31, upon request and in
minimum quantities to be defined in the order.
1

3 seats at 120°
for TCCE M4 screws

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C D E F H M Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material Kg
08 65 11 A 6.7 5.5 50 40 20.5 65 10 15 17.5 29.5 steel 0.09
08 85 11 A 12.0 7.7 70 60 40.5 85 10 15 17.5 49.5 steel 0.14
Compound: A = oil-resistant rubber

4 seats at 90° for TCCE M6 screws

VACUUM CUP WITH VULCANISED SUPPORT

Force Volume A B C D E F H M Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material Kg
08 150 11 A 42.7 47.1 139 130 41 150 10 15 17.5 115 steel 1.0
Compound: A = oil-resistant rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.29
FLAT ROUND VACUUM CUPS WITH VULCANISED SUPPORT

These cups have been designed for lifting and handling heavy
loads, both vertically and horizontally. They are vulcanised onto a
steel support and are provided with a central threaded hole for its
fastening to the automation and with a side threaded hole for vacuum
3D drawings are available on vuototecnica.net

connection.
These cups have a labyrinth graved face made with the same
compound as the cup, which allows gripping even the thinnest and
most fragile glass and marble sheets, with no bending in the gripping
area. The shape of its lip and the choice of the compound with which
they are made ensure a firm grip on uneven and corrugated surfaces.
The 08 .. 40 series, along with sharing the same features, has an
internal vertical lip which allows them to grip extremely rough
surfaces, such as embossed or profiled metal sheets, sawn marble or
granite, wooden boards, precast cement, etc.

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C D E F G H M N Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material Kg
08 110 15 M8 * 23.7 78.5 74 70 M8 110 2 14 10 26 26.0 G1/4” steel 0.35
08 110 15 * 23.7 78.5 74 70 M12 110 2 14 10 26 26.0 G1/4” steel 0.33
08 150 15 * 45.0 158.9 115 110 M12 150 2 14 10 26 40.0 G3/8” steel 0.83
08 200 10 * 78.5 341.9 164 160 M12 200 3 14 11 28 47.5 G3/8” steel 1.75
08 250 10 * 122.6 540.1 214 210 M12 250 3 14 11 28 72.5 G3/8” steel 3.00
08 300 10 * 176.6 871.8 266 260 M16 300 5 15 11 31 89.0 G1/2” steel 4.70
08 350 10 * 240.4 1210.1 316 310 M16 350 5 15 11 31 89.0 G1/2” steel 6.60
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C D E F G H M N O Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø Ø material Kg
08 110 40 M8* 9.07 77.7 74 70 M8 110 3 16 7 26 26.0 G1/4” 68 steel 0.36
08 110 40 * 9.07 77.7 74 70 M12 110 3 16 7 26 26.0 G1/4” 68 steel 0.34
08 150 40 * 21.60 156.0 115 110 M12 150 3 16 7 26 40.0 G3/8” 105 steel 0.85
08 200 40 * 42.90 334.6 164 160 M12 200 3 17 8 28 47.5 G3/8” 148 steel 1.70
08 250 40 * 75.30 546.2 214 210 M12 250 3 17 8 28 72.5 G3/8” 196 steel 3.00
08 300 40 * 120.70 874.4 266 260 M16 300 3 18 10 31 89.0 G1/2” 248 steel 4.60
08 350 40 * 174.20 1219.4 316 310 M16 350 3 18 10 31 89.0 G1/2” 298 steel 6.50
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.30
FLAT ROUND VACUUM CUP WITH VULCANISED SUPPORT

These cups are recommended for handling very

heavy loads both vertically and horizontally.
They are vulcanised onto a steel support and have a
labyrinth graved face made in the same compound

3D drawings are available on vuototecnica.net

as the cup.
The support is provided with four steel pins with
as many self-locking nuts for guiding the cups and
fastening them to the automation, as well as with a
threaded sleeve for vacuum connection.
Moreover, these cups are provided with four springs
to cushion its impact with the load to be lifted.
These cups are available in the three standard
compounds.

VACUUM CUP WITH VULCANISED SUPPORT

Force Volume A B E F G H I L Support Weight
Item
Kg cm3 Ø Ø material Kg
08 360 10 * 254.3 1397.5 M12 G1/2" 35 95 13 130 29 16 steel 4.75
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

These cups have been designed to meet the need of lifting objects with
a central hole.
Their very thin lip allows them to grip very rough surfaces, such as
grinding wheels and discs.
3D drawings are available on vuototecnica.net

They are particularly recommended for handling CDs, perforated discs,

toothed wheels, pulleys and other similar objects.
Their supports are made with anodised aluminium and are provided
with a threaded hole in the centre to allow suction, as well as its
fastening to the automation.
The cups are cold fitted onto them without any adhesives.
To guarantee maximum flexibility, the cups for gripping grinding discs
are made with natural para rubber N, while those for handling CDs are
made with silicone S. Cups in special compounds, listed on pg. 31, can
be provided upon request in minimum quantities to be defined in the
order.
To replace, simply request the single vacuum cup indicated in the table
in the desired compound.

4 holes Ø 1 at 90°
VACUUM CUP
Force Volume A B D d F H
Item
Kg cm3 Ø Ø Ø Ø Ø
01 24 06 S 0.6 1.3 25.5 15.5 24 16.5 20 6
Compound: S= silicone

SUPPORT
A B D E F H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 232 15 G1/8” 30 10 4 14 aluminium 01 24 06 16.7

VACUUM CUP WITH SUPPORT

Force A D d E H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 24 06 S 0.6 15 24 16.5 2.5 16.5 01 24 06 S 00 08 232 18.1
Compound: S= silicone

3D drawings are available on vuototecnica.net

6 holes Ø 1.5 at 60°

VACUUM CUP
Force Volume A B D d F H
Item
Kg cm3 Ø Ø Ø Ø Ø
01 31 06 S 1.25 2.0 31.5 21.5 31 18 24.5 6
Compound: S= silicone

SUPPORT
A B D E F H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 231 15 G1/8” 36 10 4 14 aluminium 01 31 06 24.9

VACUUM CUP WITH SUPPORT

Force A D d E H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 31 06 S 1.25 15 31 18 3.6 17.6 01 31 06 S 00 08 231 26.6
Compound: S= silicone

M4 screw coating

Filter

O-ring

SUPPORT
N O P Q Support For vacuum cup Weight
Item
material item g
00 08 184 60 25 55 20 aluminium 01 40 75 38.7

VACUUM CUP WITH SUPPORT

Force A B H L M P Q Vacuum cup Support Weight
Item
Kg item item g
08 40 75 M1 * 6.7 66 31 16.0 76 41 55 20 01 40 75 00 08 184 53.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.37
RECTANGULAR FLAT VACUUM CUPS WITH ANTI-SLIP SUPPORT
3D drawings are available on vuototecnica.net

VACUUM CUPS
Force Volume A B E F G H L M N O P Q
Item
Kg cm3
1 01 120 90 * 24.0 42.9 107 78 3 7.5 7.5 17.5 117 87 102 73 97 68
01 150 75 * 25.0 36.6 137 62 3 7.5 7.5 16.5 147 72 132 57 127 52
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Non-slip
plastic
coating

4 seats Filter O-ring

for TCCE M4 screw

SUPPORTS
A B C H L M N O P Q Support For vacuum cup Weight
Item
material item g
00 08 256 82 50 2.5 16.2 30 56 107 75 102 70 aluminium 01 120 90 244.5
00 08 257 110 35 2.3 16.4 20 92 135 60 130 55 aluminium 01 150 75 247.9

Force A B C D F N Vacuum cup Support Weight
Item
Kg Ø item item Kg
08 290 68 * 25 290 68 15 G3/8” 11 62 01 290 68 00 08 116 0.56
08 290 140 * 72 290 140 15 G1/2” 11 134 01 290 140 00 08 117 1.15
* Complete the code indicating the compound: OF= geranium foam rubber; NF= neoprene foam rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.40
FLAT RECTANGULAR VACUUM CUPS WITH VULCANISED SUPPORT,
FOR CLAMPING GLASS AND MARBLE
Glass and marble manufacturers’ machining centres require
increasingly accurate and safe clamping systems. This has led us to
creating this new series of cups.
They are vulcanised onto a steel support and are provided with a hole

3D drawings are available on vuototecnica.net

in the centre for vacuum connection or for a ball valve, as well as with
2 holes on the internal circumference for housing Allen screws.
Their extremely flexible lip allows them to easily adapt to the sheets
to be held, with no risk of deformation or rupture, even for the thinnest
ones.
The particular shape of the internal support plane of these cups
ensures a high friction coefficient with the gripping surface and
especially a considerable grip on wet glass and marble sheets,
thanks to the water drainage. All this guarantees a firm, safe
grip. Furthermore, these cups feature the highest accuracy of
their thickness, whose nominal height has a tolerance of only five
hundredths of millimetre.
They are normally produced with oil-resistant rubber A, but they can
be ordered in other compounds, listed on pg. 31, upon request and in
minimum quantities to be defined in the order. 1

2 seats
for TCCE M4 screws

VACUUM CUP WITH VULCANISED SUPPORT

Force Volume A B D E F H L M N P Q Support Weight
Item
Kg cm3 Ø material g
08 50 75 A 7.5 6.1 60 35 20.5 10 15 17.5 75 50 39.5 50 25 steel 92
Compound: A = oil-resistant rubber

These oval cups are recessed on moulders in order to hold

a side of the cardboard box during the moulding process by
means of traditional cups on the opposite side.
Once assembled with their support, however, they can be
3D drawings are available on vuototecnica.net

used for handling boxes, plastic objects or anything with a

limited gripping surface.
Their anodised aluminium support has a central threaded
hole to fasten it to the automation. They are also provided
with a nickel-plated brass plate to hold the cup in its
housing and with one or two stainless steel screws for
fixing them.
To replace, simply request the single vacuum cup indicated
in the table in the desired compound.

VACUUM CUP
Force Volume A B C D
Item
Kg cm3
01 12 20 * 0.52 0.3 15 11.5 17 20
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORT
B E F Support For vacuum cup Weight
Item
Ø material item g
00 08 70 G1/8” 8.5 6.5 aluminium 01 12 20 5.4

fixing plate item 00 08 97

perforated TSP M3x5 screw item 00 08 103

Note: Supplied automatically also with the fixing plate and the perforated
TSP screw when ordering item 00 08 70

VACUUM CUP WITH SUPPORT

Force D Vacuum cup Support Weight
Item
Kg item item g
08 12 20 * 0.52 20 01 12 20 00 08 70 5.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

3D drawings are available on vuototecnica.net

VACUUM CUPS
Force Volume A B C D
Item
Kg cm3
01 12 30 * 0.82 0.5 25 21.5 27 30
01 12 40 * 1.12 0.7 35 31.5 37 40
01 12 50 * 1.57 1.0 50 46.5 52 55
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
A B C E F Support For vacuum cup Weight
Item
Ø material item g
00 08 71 30 G1/8” 25 8.5 6.5 aluminium 01 12 30 7.8
00 08 75 40 G1/8” 35 8.5 6.5 aluminium 01 12 40 11.4
00 08 76 55 G1/8” 50 8.5 6.5 aluminium 01 12 50 15.5

fixing plate item 00 08 98 for supp. 00 08 71

item 00 08 99 for supp. 00 08 75
item 00 08 100 for supp. 00 08 76

2 TSP screws M3x5 item 00 08 102

Note: Supplied automatically also with

the fixing plate and the perforated TSP screw when ordering the item relative to
the support

VACUUM CUPS WITH SUPPORT

Force D Vacuum cup Support Weight
Item
Kg item item g
08 12 30 * 0.82 30 01 12 30 00 08 71 8.3
08 12 40 * 1.12 40 01 12 40 00 08 75 12.0
08 12 50 * 1.57 55 01 12 50 00 08 76 16.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Complete range of flat elliptical vacuum cups, normally used for gripping, handling and
clamping cardboard cases and boxes, wood shingles, small ceramic or brick tiles, iron or
stainless steel profiles, sheets and anything else present on long, narrow gripping
surfaces.
3D drawings are available on vuototecnica.net

Instead, bellows elliptical vacuum cups, in addition to having the same function
as the flat cups described above, are able to adapt to the gripping plane, even if
not perfectly perpendicular to the axis of the vacuum cup, and can
recover evident unevenness of the loads to be lifted.
They are normally available in the three standard compounds but
can be supplied in special compounds listed on pg. 31 and in a
minimum amount to be defined in the order, upon request.
Both items can be supplied with or without automation fastening
support. Upon request, special non-rotating vacuum cup holders on
which to assemble them are able to prevent their rotation during use.

1 VACUUM CUPS
Force A B C D E F G H I L Volume
Item
Kg Ø Ø Ø cm3
VOP 08 24 SR * 0.44 12.2 7.3 2.5 24 11.2 5.5 0.8 12.0 6.7 8.0 0.191
VOP 10 30 SR * 0.69 12.2 7.3 4.5 30 11.3 5.5 0.7 12.0 7.0 10.0 0.214
VOP 12 36 SR * 0.98 12.0 7.3 5.0 36 12.1 5.5 0.9 13.0 6.4 12.0 0.498
VOP 15 45 SR * 1.56 16.4 13.0 4.0 45 20.1 8.8 1.9 22.0 14,3 15.0 1.203
VOP 20 60 SR * 2.73 18.0 13.0 8.0 60 20.0 9.0 1.5 21.5 10.0 20.0 2.026
VOP 25 75 SR * 4.30 17.8 13.0 8.0 75 19.1 9.0 2.2 21.3 7.6 25.0 5.026
VOP 28 85 SR * 5.53 18.6 13.0 8.0 85 18.9 9.7 2.8 21.7 8.7 28.0 6.761
VOP 35 100 SR * 8.09 18.8 13.0 8.0 100 18.9 9.7 3.3 22.2 8.7 35.0 11.989
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

MALE SUPPORTS
A B D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 344 G1/8” 14 7.3 7 7 5.5 19.5 aluminium VOP 08 24 SR 18.5
Hex. B
VOP 10 30 SR
VOP 12 36 SR
00 08 346 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOP 15 45 SR 25.0 screw
00 08 404 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOP 20 60 SR 29.8 item 00 08 347 for supp.00 08 402
VOP 25 75 SR item 00 08 348 for supp.00 08 404
00 08 402 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOP 28 85 SR 30.7
VOP 35 100 SR Note: Supplied automatically also with the screw
when ordering the item relative to the support
Hex. B

VACUUM CUPS WITH MALE SUPPORT

Force A B D E F G H I L Vacuum cup Support Weight
Item
Kg Ø item item g
VOP 08 24 * 0.44 G1/8” 14 24 7 7 5.3 26.0 6.7 8.0 VOP 08 24 SR 00 08 344 19.7
VOP 10 30 * 0.69 G1/8” 14 30 7 7 5.0 26.0 7.0 10.0 VOP 10 30 SR 00 08 344 19.8
VOP 12 36 * 0.98 G1/8” 14 36 7 7 6.6 27.0 6.4 12.0 VOP 12 36 SR 00 08 344 20.6
VOP 15 45 * 1.56 G1/4” 17 45 8 8 7.7 38.0 14.3 15.0 VOP 15 45 SR 00 08 346 29.2
VOP 20 60 * 2.73 G1/4” 17 60 8 8 11.5 37.5 10.0 20.0 VOP 20 60 SR 00 08 404 38.3
VOP 25 75 * 4.30 G1/4” 17 75 8 8 13.7 37.3 7.6 25.0 VOP 25 75 SR 00 08 404 43.5
VOP 28 85 * 5.53 G1/4” 17 85 8 8 13.0 37.7 8.7 28.0 VOP 28 85 SR 00 08 402 50.7
VOP 35 100 * 8.09 G1/4” 17 100 8 8 13.5 38.2 8.7 35.0 VOP 35 100 SR 00 08 402 62.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.44
ELLIPTICAL FLAT VACUUM CUPS WITH FEMALE SUPPORTS

3D drawings are available on vuototecnica.net

VACUUM CUPS 1
Force A B C D E F G H I L Volume
Item
Kg Ø Ø Ø cm3
VOP 08 24 SR * 0.44 12.2 7.3 2.5 24 11.2 5.5 0.8 12.0 6.7 8.0 0.191
VOP 10 30 SR * 0.69 12.2 7.3 4.5 30 11.3 5.5 0.7 12.0 7.0 10.0 0.214
VOP 12 36 SR * 0.98 12.0 7.3 5.0 36 12.1 5.5 0.9 13.0 6.4 12.0 0.498
VOP 15 45 SR * 1.56 16.4 13.0 4.0 45 20.1 8.8 1.9 22.0 14.3 15.0 1.203
VOP 20 60 SR * 2.73 18.0 13.0 8.0 60 20.0 9.0 1.5 21.5 10.0 20.0 2.026
VOP 25 75 SR * 4.30 17.8 13.0 8.0 75 19.1 9.0 2.2 21.3 7.6 25.0 5.026
VOP 28 85 SR * 5.53 18.6 13.0 8.0 85 18.9 9.7 2.8 21.7 8.7 28.0 6.761
VOP 35 100 SR * 8.09 18.8 13.0 8.0 100 18.9 9.7 3.3 22.2 8.7 35.0 11.989
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

FEMALE SUPPORTS
A B D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 343 G1/8” 14 7.3 10 8.0 5.5 15.5 aluminium VOP 08 24 SR 16.8 Hex. B

VOP 10 30 SR
VOP 12 36 SR
00 08 345 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOP 15 45 SR 19.9 screw
00 08 405 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOP 20 60 SR 24.7 item 00 08 347 for supp.00 08 403
VOP 25 75 SR item 00 08 348 for supp.00 08 405
00 08 403 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOP 28 85 SR 25.6
VOP 35 100 SR Note: Supplied automatically also with the screw
when ordering the item relative to the support
Hex. B

VACUUM CUPS WITH FEMALE SUPPORT

Force A B D F G H I L Vacuum cup Support Weight
Item
Kg Ø item item g
VOP 08 24 F * 0.44 G1/8” 14 24 10 5.3 22.0 6.7 8.0 VOP 08 24 SR 00 08 343 18.0
VOP 10 30 F * 0.69 G1/8” 14 30 10 5.0 22.0 7.0 10.0 VOP 10 30 SR 00 08 343 18.1
VOP 12 36 F * 0.98 G1/8” 14 36 10 6.6 23.0 6.4 12.0 VOP 12 36 SR 00 08 343 18.9
VOP 15 45 F * 1.56 G1/4” 17 45 12 7.7 24.0 14.3 15.0 VOP 15 45 SR 00 08 345 23.9
VOP 20 60 F * 2.73 G1/4” 17 60 12 11.5 33.5 10.0 20.0 VOP 20 60 SR 00 08 405 33.2
VOP 25 75 F * 4.30 G1/4” 17 75 12 13.7 33.3 7.6 25.0 VOP 25 75 SR 00 08 405 38.4
VOP 28 85 F * 5.53 G1/4” 17 85 12 13.0 33.7 8.7 28.0 VOP 28 85 SR 00 08 403 45.6
VOP 35 100 F * 8.09 G1/4” 17 100 12 13.5 34.2 8.7 35.0 VOP 35 100 SR 00 08 403 57.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.45
ELLIPTICAL BELLOWS VACUUM CUPS WITH MALE SUPPORTS
3D drawings are available on vuototecnica.net

VACUUM CUPS
Force A B C D E F G H L Volume
Item
Kg Ø Ø Ø bellows stroke cm3
VOS 08 25 * 0.51 10.0 7.3 1.3 25.0 12.4 6.0 3.0 18.4 8.0 0.852
VOS 15 45 * 1.56 17.2 13.0 4.0 45.0 18.6 10.0 6.5 28.6 15.0 4.978
VOS 25 75 * 4.30 17.2 13.0 9.0 75.0 25.2 9.0 8.5 34.2 25.0 23.083
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

screw
item 00 08 347 for supp.00 08 402

Hex. B Note: Supplied automatically also with the screw

when ordering the item relative to the support

MALE SUPPORTS
A B D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 344 G1/8” 14 7.3 7 7 5.5 19.5 aluminium VOS 08 25 18.5
00 08 346 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOS 15 45 25.0
00 08 402 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOS 25 75 30.7

Hex. B

VACUUM CUPS WITH MALE SUPPORT

Force A B D E G H L Vacuum cup Support Weight
Item
Kg Ø item item g
VOS 08 25 M * 0.51 G1/8” 14 25.0 20.0 12.4 32.4 8.0 VOS 08 25 00 08 344 20.0
VOS 15 45 M * 1.56 G1/4” 17 45.0 26.0 18.6 44.6 15.0 VOS 15 45 00 08 346 31.4
VOS 25 75 M * 4.30 G1/4” 17 75.0 25.0 25.2 50.2 25.0 VOS 25 75 00 08 402 47.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

3D drawings are available on vuototecnica.net

screw
item 00 08 347 for supp.00 08 403

Hex. B Note: Supplied automatically also with the screw

when ordering the item relative to the support

FEMALE SUPPORTS
A B D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 343 G1/8” 14 7.3 10 8.0 5.5 15.5 aluminium VOS 08 25 16.8
00 08 345 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOS 15 45 19.9
00 08 403 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOS 25 75 25.6

Hex. B

VACUUM CUPS WITH FEMALE SUPPORT

Force A B D F G H L Vacuum cup Support Weight
Item
Kg Ø item item g
VOS 08 25 F * 0.51 G1/8” 14 25.0 16.0 12.4 28.4 8.0 VOS 08 25 00 08 343 18.3
VOS 15 45 F * 1.56 G1/4” 17 45.0 22.0 18.6 40.6 15.0 VOS 15 45 00 08 345 26.3
VOS 25 75 F * 4.30 G1/4” 17 75.0 21.0 25.2 46.2 25.0 VOS 25 75 00 08 403 42.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

The cups described on this page have been

designed for handling X-ray sheets in hospital or
other electrostatically charged films.
Their original shape allows them to pick up one
3D drawings are available on vuototecnica.net

sheet at a time without deforming or crumpling

the gripping surface and without leaving stains
or prints, thanks to the special compound with
which they are made. Their aluminium supports
are vulcanised onto the cups. One with a smooth
hole for fixing the cup to the machine with an Allen
screw, with the housing on the inside and one
with a threaded hole. A side slot on the support
prevents the cup from rotating. These cups are
recommended for gripping and handling magnetic
sheets, plastic sheets, thin rubber sheets, laminated
cardboard, etc.

VACUUM CUP WITH VULCANISED SUPPORT

Force Volume Support Weight
Item
Kg cm3 material g
08 32 52 A 3.00 3.1 aluminium 12.1
Compound: A = oil-resistant rubber

VACUUM CUP WITH VULCANISED SUPPORT

Force Volume Support Weight
Item
Kg cm3 material g
08 32 99 A 3.00 3.1 aluminium 11.9
Compound: A = oil-resistant rubber

These cups have been designed for gripping and

handling cylindrical objects, such as pipes, bottles,
round profiles, etc.
Their aluminium support is vulcanised onto the cup

3D drawings are available on vuototecnica.net

and it is provided with a central threaded hole to
ease its fastening to the automation and with a side
hole for insertion of an anti-rotation guide pin.
These cups can be provided in the three standard
compounds: oil-resistant rubber A, natural para
rubber N and silicone S.

CONCAVE VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume gripping Ø A B C D E F G H I L M N Support Weight
Item
Kg cm3 min max Ø Ø material g
08 30 60 * 3.5 2.1 30 45 26 15 10 M8 8 16 19 20.0 20 60 50 4.1 aluminium 20.3
08 40 90 * 8.6 5.5 50 80 40 20 14 M12 10 23 28 25.0 30 92 80 5.1 aluminium 54.8
08 50 90 * 10.5 11.1 60 95 48 22 14 M12 10 28 34 28.5 30 92 80 5.1 aluminium 62.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

The foam rubber used for our cups can be provided in sheets or strips
of the sizes indicated in the table.
Both the OF foam rubber strips and the sheets have a self-adhesive
side which allows a quick and easy fixing to the metal support.
3D drawings are available on vuototecnica.net

These sheets and strips can be used to make cups of every shape and
to handle loads with raw or very rough surfaces. They can be supplied
in different sizes and density upon request and in quantities to be
defined in the order.
The working temperature ranges from -40°C to +80°C.
Excellent compressive and breaking strength, with elongation up to
350%. Poor resistance to oils, ozone and flame.
NOTE: OF foam rubber is obtained by the expansion of a natural
rubber, subjected to leavening through a chemical-thermal
treatment.
Surface porosity with the same density, therefore, can vary, not
compromising its effectiveness.

Self-adhesive side
OF FOAM RUBBER SHEETS
A B E
Item

LGS 10 OF 2050/1950 920/880 10 ± 1.50

LGS 15 OF 2050/1950 920/880 15 ± 1.60
LGS 20 OF 2050/1950 920/880 20 ± 1.90
LGS 25 OF 2050/1950 920/880 25 ± 1.90
LGS 30 OF 2050/1950 920/880 30 ± 2.00
LGS 40 OF 2050/1950 920/880 40 ± 2.50
LGS 45 OF 2050/1950 920/880 45 ± 2.50
Note: The minimum size available is half a sheet.
Note: Considering the nature of OF rubber foam, the size of slabs in the table may vary, even beyond tolerances.
Self-adhesive side

OF FOAM RUBBER STRIPS

A B E
Item

SGS 10 10 OF 2050/1950 10 ± 1.50 10 ± 0,50

SGS 15 10 OF 2050/1950 15 ± 1.60 10 ± 0,50
SGS 20 10 OF 2050/1950 20 ± 1.90 10 ± 0,50
SGS 20 15 OF 2050/1950 20 ± 1.90 15 ± 0,75
Note: Considering the nature of OF rubber foam, the size of strips in the table may vary.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.50
SB EXTRA SOFT FOAM RUBBER SHEETS

Specifically designed for the production of OCTOPUS system gripping

surface. This black foam rubber has an open cellular structure and is
made of EPDM rubber.
SB extra soft foam rubber sheets have a self-adhesive side for quick,

3D drawings are available on vuototecnica.net

easy fixing to metal supports.
The temperature of use ranges from -40°C to + 130°C and it offers
excellent resistance to heat, atmospheric agents, low temperatures
and ageing.
The low density and softness of this foam rubber allows gripping
surfaces to adapt to any kind of surface.

1
SB EXTRA SOFT FOAM RUBBER SHEETS

Self-adhesive side
A B E
Item

LGS 10 SB 2050/1950 920/880 10 ± 1.50

LGS 15 SB 2050/1950 920/880 15 ± 1.60
LGS 20 SB 2050/1950 920/880 20 ± 1.90
LGS 30 SB 2050/1950 920/880 30 ± 2.00
LGS 40 SB 2050/1950 920/880 40 ± 2.50
Note: The minimum size available, half a sheet.

NF NEOPRENE FOAM RUBBER SHEETS

This type of foam rubber made with Neoprene rubber is black in

colour and has a closed cellular structure, allowing it to offer greater
compressive strength at the cost of less elasticity and a tendency to
deform over time.
NF Neoprene foam rubber sheets have a self-adhesive side for quick,
easy fixing to metal supports. Excellent resistance to oil products,
sunlight, atmospheric agents, and ozone. Not recommended for food
use.
This type of foam rubber allows for the use of vacuum cups for gripping
coarse or very rough surfaces operating outside in contact with
atmospheric agents.
The working temperature ranges for the foam are from -40°C to +100 °C.

NF NEOPRENE FOAM RUBBER SHEETS

Self-adhesive side

A B E
Item

LGS 10 NF 2050/1950 920/880 10 ± 1.50

LGS 15 NF 2050/1950 920/880 15 ± 1.60
LGS 20 NF 2050/1950 920/880 20 ± 1.90
LGS 30 NF 2050/1950 920/880 30 ± 2.00
LGS 40 NF 2050/1950 920/880 40 ± 2.50
Note: The minimum size available, half a sheet.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.51
BELLOWS CUPS WITH SUPPORTS
FOR GRIPPING FLOW PACKS
Thanks to their specific conformation and flexibility,
the vacuum cups illustrated and described on
this page are especially suitable for installation
on automatic, high production machines in the
3D drawings are available on vuototecnica.net

packaging sector, and for the gripping and handling

of flow packs.
The vacuum cups are available in different
compounds for food use and can be cold fitted on
their special supports without the aid of adhesives.
Upon request, these cups can be provided upon
request in minimum quantities and in other special
compounds, listed on pg. 31, to be defined in the
order.

VACUUM CUPS
Force Volume A B C D E F H Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø mm
01 20 30 S 0.78 3.0 13 8 12 20 10 11.5 30 11
01 30 45 S 1.76 11.4 18 11 19 30 16 19.0 45 20
Compound: S= silicone

Hex. 17
SUPPORTS
D E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 18 9.5 8 14 10 32 aluminium 01 20 30 10.3
00 08 127 13.5 8 14 15 37 aluminium 01 30 45 11.5

Sp B

VACUUM CUPS WITH SUPPORT

Force B C D E F G H Vacuum cup Support Weight
Item
Kg Ø Ø item item g
08 20 30 S 0.78 17 G1/4” 20 8 14 30 52 01 20 30 00 08 18 12.5
08 30 45 S 1.76 17 G1/4” 30 8 14 45 67 01 30 45 00 08 127 18.4
Compound: S= silicone

The bellows cups described on these pages have been specially

designed for handling baked goods, such as biscuits, bread, pizza,
etc., as well as plastic or paper bags containing chocolates, sweets,
pasta, flour, powder, etc.

3D drawings are available on vuototecnica.net

Thanks to their great flexibility, they can also be used to compensate
flatness errors or for gripping on inclined surfaces. Their anodised
aluminium supports are provided with a threaded male or female
central pin to allow suction and to fasten it to the automation.
The vacuum cups can be fitted on them without the aid of adhesives.
To replace, simply request the single vacuum cup indicated in the
table in the desired compound.

VACUUM CUPS
Force Volume A B C D E F H Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø mm
01 20 23 * 0.78 3.4 14.5 5.0 14 20 5 4 23 16
01 30 32 * 1.76 11.4 20.0 6.5 21 30 7 5 32 22
01 40 42 * 3.14 33.0 20.0 6.5 28 40 7 5 42 32
01 50 53 * 4.90 53.3 27.0 10.5 35 50 10 6 53 32
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

MALE SUPPORTS
A B C D E F G H Support For vacuum cup Weight Sp B
Item
Ø Ø Ø material item g
00 08 133 14.5 13 G1/8” 8.5 5.5 8 5.0 18.5 aluminium 01 20 23 3.5
00 08 135 20.0 17 G1/4” 10.0 7.5 12 7.5 27.0 aluminium 01 30 32 9.5
01 40 42
00 08 142 27.0 22 G1/4” 14.0 7.5 12 9.5 29.0 aluminium 01 50 53 15.7

Sp B
VACUUM CUPS WITH MALE SUPPORT
Force A B C D E F G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 20 23 * 0.78 14.5 13 G1/8” 20 5.5 8 23 36.5 01 20 23 00 08 133 5.3
08 30 32 * 1.76 20.0 17 G1/4” 30 7.5 12 32 51.5 01 30 32 00 08 135 15.1
08 40 42 * 3.14 20.0 17 G1/4” 40 7.5 12 42 61.5 01 40 42 00 08 135 21.1
08 50 53 * 4.90 27.0 22 G1/4” 50 7.5 12 53 72.5 01 50 53 00 08 142 40.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

VACUUM CUP ACCESSORIES

STAINLESS STEEL DISC FILTERS

D For vacuum cup
Item
Ø item
00 08 295 17 01 20 23
00 08 293 27 01 30 32
00 08 279 35 01 40 42

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.53
BELLOWS VACUUM CUPS WITH FEMALE SUPPORTS
3D drawings are available on vuototecnica.net

FEMALE SUPPORTS
A B C D E F G H Support For vacuum cup Weight Sp B
Item
Ø Ø Ø material item g
00 08 132 14.5 13 G1/8” 8.5 12 8 5.0 17.0 aluminium 01 20 23 3.8
00 08 134 20.0 17 G1/4” 10.0 14 10 7.5 21.5 aluminium 01 30 32 8.3
01 40 42
00 08 141 27.0 22 G1/4” 14.0 14 10 9.5 23.5 aluminium 01 50 53 19.7

Sp B
VACUUM CUPS WITH FEMALE SUPPORT
Force A B C D E F G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 20 23 F * 0.78 14.5 13 G1/8” 20 12 8 23 35 01 20 23 00 08 132 5.6
08 30 32 F * 1.76 20.0 17 G1/4” 30 14 10 32 46 01 30 32 00 08 134 13.9
08 40 42 F * 3.14 20.0 17 G1/4” 40 14 10 42 56 01 40 42 00 08 134 19.9
08 50 53 F * 4.90 27.0 22 G1/4” 50 14 10 53 67 01 50 53 00 08 141 44.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

VACUUM CUP ACCESSORIES

STAINLESS STEEL DISC FILTERS

D For vacuum cup
Item
Ø item

00 08 295 17 01 20 23
00 08 293 27 01 30 32
00 08 279 35 01 40 42

The particular shape of these bellows cups allows them to

quickly crumple up when in contact with the surface of the
load to be lifted and in presence of a vacuum. This quick

3D drawings are available on vuototecnica.net

movement prevents the load below from remaining stuck to
the surfaces or load underneath.
Thanks to this particular feature, these bellows cups are
recommended for handling paper and cardboard sheets,
thin metal sheets, wooden panels, glass sheets etc.
Thanks to their great flexibility, they can also be used to
compensate flatness errors or for gripping on inclined
surfaces. Their anodised aluminium supports are provided
with a threaded male or female central pin to allow suction
and to fasten it to the automation. The vacuum cups can be
fitted on them without the aid of adhesives.
To replace, simply request the single vacuum cup indicated
in the table in the desired compound.

VACUUM CUPS
Force Volume A B C D E F H Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø mm
01 22 19 * 0.95 2.5 14.5 5.0 11.0 22 4 5.5 19 10
01 34 26 * 2.26 8.0 14.5 5.0 17.0 34 4 5.5 26 12
01 43 28 * 3.62 15.3 20.0 6.5 21.5 43 4 7.0 28 14
01 53 35 * 5.51 30.5 27.0 10.5 30.5 53 6 9.5 35 16
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

MALE SUPPORTS
Sp B
A B C D E F G H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 133 14.5 13 G1/8” 8.5 5.5 8 5.0 18.5 aluminium 01 22 19 3.5
01 34 26
00 08 135 20.0 17 G1/4” 10.0 7.5 12 7.5 27.0 aluminium 01 43 28 9.5
00 08 142 27.0 22 G1/4” 14.0 7.5 12 9.5 29.0 aluminium 01 53 35 15.7

VACUUM CUPS WITH MALE SUPPORT Sp B

Force A B C D E F G H Vacuum cup Support Weight

Item
Kg Ø Ø Ø item item g
08 22 19 * 0.95 14.5 13 G1/8” 22 5.5 8 19 32.5 01 22 19 00 08 133 6.2
08 34 26 * 2.26 14.5 13 G1/8” 34 5.5 8 26 39.5 01 34 26 00 08 133 15.2
08 43 28 * 3.62 20.0 17 G1/4” 43 7.5 12 28 47.5 01 43 28 00 08 135 18.5
08 53 35 * 5.51 27.0 22 G1/4” 53 7.5 12 35 54.5 01 53 35 00 08 142 33.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.55
REINFORCED BELLOWS VACUUM CUPS WITH FEMALE SUPPORTS
3D drawings are available on vuototecnica.net

FEMALE SUPPORTS
A B C D E F G H Support For vacuum cup Weight Sp B
Item
Ø Ø Ø material item g
00 08 132 14.5 13 G1/8” 8.5 8 12 5.0 17.0 aluminium 01 22 19 3.8
01 34 26
00 08 134 20.0 17 G1/4” 10.0 10 14 7.5 21.5 aluminium 01 43 28 8.3
00 08 141 27.0 22 G1/4” 14.0 10 14 9.5 23.5 aluminium 01 53 35 19.7

Sp B
VACUUM CUPS WITH FEMALE SUPPORT
Force A B C D E F G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 22 19 F * 0.95 14.5 13 G1/8” 22 8 12 19 31 01 22 19 00 08 132 6.5
08 34 26 F * 2.26 14.5 13 G1/8” 34 8 12 26 38 01 34 26 00 08 132 9.5
08 43 28 F * 3.62 20.0 17 G1/4” 43 10 14 28 42 01 43 28 00 08 134 17.3
08 53 35 F * 5.51 27.0 22 G1/4” 53 10 14 35 49 01 53 35 00 08 141 37.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

The cups described on these pages share the same

features with the previously described bellows
cups, only these have larger dimensions that allow
them to lift much heavier loads; moreover, their

3D drawings are available on vuototecnica.net

anodised aluminium supports also have a central
threaded hole for their fastening to the automation.
The larger ones also have an additional side hole
for vacuum connection. The difference is that
these supports are provided with a disc instead of
with a pin. These cups can be cold fitted onto their
supports without any adhesives.
To replace, simply request the single vacuum cup
indicated in the table in the desired compound.

VACUUM CUP
Force Volume A B C D G H M Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø Ø mm
01 75 42 * 11.93 89.4 59 54 45 78 22.5 42 56 22.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
A B D E H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 126 45 M12 54 3 10 aluminium 01 75 42 45.5
00 08 465 45 G1/4” 54 3 10 aluminium 01 75 42 41.5
00 08 193 45 G3/8” 54 3 10 aluminium 01 75 42 41.5
00 08 143 45 G1/2” 54 3 10 aluminium 01 75 42 41.5

VACUUM CUPS WITH SUPPORT

Force A B D G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 75 42 * 11.93 59 M12 78 22.5 42 01 75 42 00 08 126 94.8
08 75 42 1/4” * 11.93 59 G1/4” 78 22.5 42 01 75 42 00 08 465 90.8
08 75 42 3/8” * 11.93 59 G3/8” 78 22.5 42 01 75 42 00 08 193 90.8
08 75 42 1/2” * 11.93 59 G1/2” 78 22.5 42 01 75 42 00 08 143 90.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.57
REINFORCED BELLOWS VACUUM CUPS WITH SUPPORTS
3D drawings are available on vuototecnica.net

VACUUM CUPS
Force Volume A B C D G H M Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø Ø mm
01 110 58 * 23.70 281.9 75 70 61 110 33 58 74 33
01 150 74 * 45.00 726.1 112 107 98 150 49 74 103 49
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

SUPPORTS
A B C D E N H Support For vacuum cup Weight
Item
Ø Ø Ø Ø material item g
00 08 162 61 G1/2” G1/8” 70 3 23 10 aluminium 01 110 58 78.9
00 08 163 98 G1/2” G1/8” 107 3 35 10 aluminium 01 150 74 211.8

VACUUM CUPS WITH SUPPORT

Force A B C D H N Vacuum cup Support Weight
Item
Kg Ø Ø Ø Ø item item g
08 110 58 * 23.70 75 G1/2” G1/8” 110 58 23 01 110 58 00 08 162 190.7
08 150 74 * 45.00 112 G1/2” G1/8” 150 74 35 01 150 74 00 08 163 458.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

This range of cups has been designed for vertically gripping stocked
glass sheets. By laying the cup on the glass surface and opening the
vacuum, the sheet will place itself orthogonally to the floor perfectly
adhering to the cup internal face. The glass sheet can then be

3D drawings are available on vuototecnica.net

handled in any direction in full safety.
Their aluminium support has a central threaded hole for fastening it
to the machine and for the vacuum connection. These cups can be
cold fitted onto their supports without any adhesives.

VACUUM CUPS
Force Volume A B C D G H M N Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø Ø Ø mm
01 150 55 * 45.00 471.6 78 70 58 150 33 55 120 125 33
01 210 60 * 86.50 1220.6 138 130 118 210 38 61 180 185 38
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber

SUPPORTS
A B C D E H Support For vacuum cup Weight
Item
Ø Ø Ø Ø material item g
00 08 280 35 G1/2” -- 70 12.5 22.5 aluminium 01 150 55 120
00 08 281 65 G1/2” -- 130 12.5 23.5 aluminium 01 210 60 465
00 08 286 35 --- 8 70 12.5 22.5 aluminium 01 150 55 125
00 08 287 65 --- 8 130 12.5 23.5 aluminium 01 210 60 470

VACUUM CUPS WITH SUPPORT

Force A B C D G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø Ø item item g
08 150 55 * 45.00 78 G1/2” -- 150 33 60 01 150 55 00 08 280 245
08 210 60 * 86.50 138 G1/2” -- 210 38 67 01 210 60 00 08 281 650
08 150 56 * 45.00 78 --- 8 150 33 60 01 150 55 00 08 286 250
08 210 61 * 86.50 138 --- 8 210 38 67 01 210 60 00 08 287 655
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.59
VACUUM CUPS WITH TWO BELLOWS FOR HEAVY-DUTY PACKAGING

Specifically designed vacuum cups for tripping and handling particularly heavy boxes and
cardboard packaging in general.
Their thick, sturdy lip absorbs tears and sudden accelerations, typical of robotised
movements. The double bellows enables improved adaptability to the gripping surface,
3D drawings are available on vuototecnica.net

even if not perfectly perpendicular to the axis of the vacuum cup, and can recover evident
unevenness of the loads to be lifted.
The supports, all made of anodised aluminium, are equipped with a male or female central
threaded pin to allow suctioning and clamping to the automation. The vacuum cups can
be fitted on them without the aid of adhesives.
To replace, simply request the single vacuum cup indicated in the table in the desired
compound.

1
VACUUM CUPS
Force Volume A B C D E F H L Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø mm
01 35 27 * 2.26 7.3 20 7.5 34 37 11.5 6.2 27 15.5 13
01 52 40 * 5.31 25.2 27 11.5 52 55 16.0 8.2 39 23.0 20
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Sp B

MALE SUPPORTS
A B C D E F G H I L Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 394 20 17 G1/8” 11 6.0 8 7.2 21.2 M5 8 aluminium 01 35 27 6.2
00 08 395 27 20 G1/8” 15 7.5 8 9.2 24.7 M5 8 aluminium 01 52 40 13.2
00 08 366 20 17 G1/4” 11 6.0 8 7.2 21.2 M8 11 aluminium 01 35 27 6.2
00 08 364 27 20 G1/4” 15 7.5 8 9.2 24.7 M8 11 aluminium 01 52 40 13.2

Sp B

VACUUM CUPS WITH MALE SUPPORT

Force A B C D E F G H I L Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 35 27 1/8 * 2.26 20 17 G1/8” 37 6.0 8 27 41.0 M5 8 01 35 27 00 08 394 13.0
08 52 40 1/8 * 5.31 27 20 G1/8” 55 7.5 8 39 54.5 M5 8 01 52 40 00 08 395 34.5
08 35 27 * 2.26 20 17 G1/4” 37 6.0 8 27 41.0 M8 11 01 35 27 00 08 366 12.9
08 52 40 * 5.31 27 20 G1/4” 55 7.5 8 39 54.5 M8 11 01 52 40 00 08 364 34.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.60
VACUUM CUPS WITH TWO BELLOWS WITH FEMALE SUPPORTS

3D drawings are available on vuototecnica.net

Sp B

FEMALE SUPPORTS
A B C D E F G H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 396 20 17 G1/8” 11 14 8 7.2 21.2 aluminium 01 35 27 9.7
00 08 397 27 20 G1/8” 15 14 8 9.2 23.2 aluminium 01 52 40 20.0
00 08 392 20 17 G1/4” 11 14 10 7.2 21.2 aluminium 01 35 27 7.8
00 08 393 27 20 G1/4” 15 14 10 9.2 23.2 aluminium 01 52 40 18.1

Sp B

VACUUM CUPS WITH FEMALE SUPPORT

Force A B C D E F G H Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 35 27 1/8 F * 2.26 20 17 G1/8” 37 14 8 27 41 01 35 27 00 08 396 16.5
08 52 40 1/8 F * 5.31 27 20 G1/8” 55 14 8 39 53 01 52 40 00 08 397 41.3
08 35 27 F * 2.26 20 17 G1/4” 37 14 10 27 41 01 35 27 00 08 392 14.6
08 52 40 F * 5.31 27 20 G1/4” 55 14 10 39 53 01 52 40 00 08 393 39.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.61
VACUUM CUPS WITH TWO BELLOWS WITH MALE SUPPORTS
3D drawings are available on vuototecnica.net

1
VACUUM CUPS
Force Volume A B C D E F H L Bellows stroke
Item
Kg cm3 Ø Ø Ø Ø mm
08 75 43 SR * 11.19 74.3 43.0 G1/4” 75.5 80.5 17.5 13.7 50 32.5 28
08 110 73 SR * 24.17 250.6 63.5 G3/8” 113.4 119.0 25.5 19.4 75 49.5 40
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

MALE SUPPORTS
B C D E F G H I L Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 373 8 G1/4” G1/4” 2 10 10 22 M8 11 aluminium 08 75 43 SR 4.1
00 08 372 8 G3/8” G1/4” 2 13 10 25 M8 11 aluminium 08 75 43 SR 7.4
00 08 376 8 G3/8” G3/8” 3 13 15.5 31.5 M8 11 aluminium 08 110 73 SR 14.1
00 08 375 8 G1/2” G3/8” 3 13 15.5 31.5 M8 11 aluminium 08 110 73 SR 15.5

VACUUM CUPS WITH MALE SUPPORT

Force A B C D F G H I L Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 75 43 M * 11.19 43.0 8 G1/4” 80.5 10 50 60 M8 11 08 75 43 SR 00 08 373 75.0
08 75 43 3/8 M * 11.19 43.0 8 G3/8” 80.5 13 50 63 M8 11 08 75 43 SR 00 08 372 78.3
08 110 73 M * 24.17 63.5 8 G3/8” 119.0 13 75 88 M8 11 08 110 73 SR 00 08 376 220.3
08 110 73 1/2 M * 24.17 63.5 8 G1/2” 119.0 13 75 88 M8 11 08 110 73 SR 00 08 375 221.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.62
VACUUM CUPS WITH TWO BELLOWS WITH FEMALE SUPPORTS

3D drawings are available on vuototecnica.net

Sp B

FEMALE SUPPORTS
B C D E F G H I L M Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 374 22 G3/8” G1/4” 1.5 14 10.0 25.5 M8 10 11 aluminium 08 75 43 SR 12.0
00 08 377 23 G1/2” G3/8” 3.0 17 15.5 35.5 M8 13 11 aluminium 08 110 73 SR 17.8

Sp B

VACUUM CUPS WITH FEMALE SUPPORT

Force A B C D F G H I L M Vacuum cup Support Weight
Item
Kg Ø Ø Ø item item g
08 75 43 3/8 * 11.19 43.0 22 G3/8” 80.5 14 50 64 M8 10 11 08 75 43 SR 00 08 374 82.9
08 110 73 1/2 * 24.17 63.5 23 G1/2” 119.0 17 75 92 M8 13 11 08 75 43 SR 00 08 377 224.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.63
VACUUM CUPS WITH ONE BELLOW WITH VULCANISED SUPPORT

The cups described on this page, unlike the previous ones,

are vulcanised onto an aluminium hexagonal support
with a male or female threaded connector, inside of which
there is an M8 threaded hole for the possible insertion of a
3D drawings are available on vuototecnica.net

calibrated grub screw (see page 1.131).

The main feature of these bellows cups is that they quickly
crumple up during the grip, thus lifting the load for a few
centimetres, independently of the movements of the lifting
frame; this quick movement avoids that the load beneath,
remains stuck to the lifted one.
Due to this feature, they are particularly suited for handling
thin metal sheets, glass sheets, chipboard or compressed
wood panels, laminated plastic etc.
Thanks to their great flexibility, they can also be used to
compensate flatness errors or for gripping on inclined
surfaces.
The cups are provided in standard compounds and, upon
request, can be provided in minimum quantities and in other
1 special compounds, listed on pg. 31, to be defined in the
order.

Hex. 20

VACUUM CUPS WITH ONE BELLOWS WITH WITH VULCANISED FEMALE SUPPORT
Force Volume D E F G H Bellows stroke Support Weight
Item
Kg cm3 Ø mm material g
08 40 30 * 3.14 16.2 40 35 17 18 52 12 aluminium 32.4
08 50 30 * 4.90 27.9 50 37 17 20 54 13 aluminium 40.9
08 60 30 * 7.06 46.8 60 39 17 21 56 14 aluminium 53.6
08 85 30 * 14.08 107.2 85 50 17 31 67 21 aluminium 122.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 20

VACUUM CUPS WITH ONE BELLOWS WITH WITH VULCANISED MALE SUPPORT
Force D E F G H Support Weight
Item
Kg Ø material g
08 40 30 M * 3.14 40 35 13.5 18 56.5 aluminium 29.1
08 50 30 M * 4.90 50 37 13.5 20 58.5 aluminium 39.0
08 60 30 M * 7.06 60 39 13.5 21 60.5 aluminium 51.2
08 85 30 M * 14.08 85 50 13.5 31 71.5 aluminium 115.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.64
VACUUM CUPS WITH TWO BELLOWS WITH VULCANISED SUPPORT

These cups are the same as the

ones described in the previous
page, only with an additional
bellows.

3D drawings are available on vuototecnica.net

The technical features and
availability are the same.

1
Hex. 20

VACUUM CUPS WITH TWO BELLOWS WITH FEMALE VULCANISED SUPPORT

Force Volume A D E F G H Bellows stroke Support Weight
Item
Kg cm3 Ø Ø mm material g
08 40 60 * 3.14 23.6 G1/4” 40 52 17 35 69 20 aluminium 39.6
08 50 50 * 4.90 41.6 G1/4” 50 55 17 38 72 24 aluminium 49.6
08 60 50 * 7.06 63.0 G1/4” 60 58 17 41 75 25 aluminium 72.4
08 60 50M12 * 7.06 63.0 M12 60 58 17 41 75 25 aluminium 73.0
08 85 50 * 14.08 175.6 G1/4” 85 78 17 58 95 38 aluminium 168.0
08 85 50M12 * 14.08 175.6 M12 85 78 17 58 95 38 aluminium 169.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 20

VACUUM CUPS WITH TWO BELLOWS WITH MALE VULCANISED SUPPORT

Force D E F G H Support Weight
Item
Kg Ø material g
08 40 60M * 3.14 40 52 13.5 35 73.5 aluminium 35.5
08 50 50M * 4.90 50 55 13.5 38 76.5 aluminium 49.3
08 60 50M * 7.06 60 58 13.5 41 79.5 aluminium 66.0
08 85 50M * 14.08 85 78 13.5 58 99.5 aluminium 157.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.65
BELLOWS VACUUM CUPS WITH VULCANISED SUPPORT

The main feature of these bellows cups is that

they quickly crumple up during the grip, thus lifting
the load for a few centimetres, independently of
the movements of the lifting frame; this quick
3D drawings are available on vuototecnica.net

movement avoids that the load beneath, remains

stuck to the lifted one.
Due to this feature, they are particularly suited for
handling thin metal sheets, glass sheets, chipboard
or compressed wood panels, laminated plastic etc.
Thanks to their great flexibility, they can also be
used to compensate flatness errors or for gripping
on inclined surfaces. These bellows cups are
vulcanised onto a galvanised steel support or
aluminium support and are provided with a central
threaded hole for its fastening to the automatism
and with a side threaded hole for vacuum
connection or vacuum degree detection.
This range of cups is available in the three standard
1 compounds.

BELLOWS VACUUM CUPS WITH VULCANISED SUPPORT

Force Volume A B C D E G H M N Bellows stroke Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø mm material Kg
08 110 30 * 23.7 103.2 78 65 G1/8” 110 10 23 45 55 23 20 steel 0.35
08 150 30 * 45.0 323.3 78 65 G1/8” 150 10 33 60 75 23 31 steel 0.49
08 180 30 * 63.5 503.0 94 80 G1/8” 180 10 33 70 84 30 31 steel 0.81
08 250 30 * 122.6 1528.3 130 100 G3/8” 250 15 49 100 125 35 45 aluminium 1.54
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

The cups shown on this page and on the next have been
designed to solve many of the gripping and handling
problems we have encountered in over thirty years of
activity. They differ from all the other cups for the variety of

3D drawings are available on vuototecnica.net

their shapes.
They are suited for gripping CDs, labels, bags, paper or
plastic sheets, stickers, chocolates, cardboard, tiles, small
metal objects, plastic objects, etc.
Their nickel-plated brass or anodised aluminium supports
are provided with a threaded male or female pin to enable
suction and to fasten them to the automation.
These cups can be manually assembled onto their supports
with no adhesives, simply by pressing them in. They are
provided in standard compounds and, upon request, can
be provided in minimum quantities and in other special
compounds, listed on pg. 31, to be defined in the order.

Hex. 8 1
Hex. 8

Force Volume Support Support Weight Vacuum cup wit upport Weight
Vacuum cup item
Kg mm3 item material g item g
01 07 13 * 0.10 19 00 08 236 brass 3 08 07 13 * 3.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 8
Hex. 8

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 08 07 * 0.13 31 00 08 237 brass 3 08 08 07 * 3.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12 Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 11 08 * 0.24 95 00 08 238 brass 7 08 11 08 * 7.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.67
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12 Hex. 12
3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 14 09 * 0.38 220 00 08 239 brass 8.0 08 14 09 * 8.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12 Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 14 09 * 0.38 220 00 08 240 brass 7.0 08 14 09 F * 7.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12 Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 14 10 * 0.38 301 00 08 03 brass 9.0 08 14 10 * 9.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber

Hex. 12 Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 14 10 * 0.38 301 00 08 04 brass 8.1 08 14 10 F * 8.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.68
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12
Hex. 12

3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
1
01 14 15 * 0.38 270 00 08 67 brass 11.4 08 14 15 * 11.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14
Hex. 14

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 14 15 * 0.38 270 00 08 64 brass 13.9 08 14 15 F * 14.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 14 32 * 0.38 397 00 08 03 brass 9.0 08 14 32 * 10.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.69
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12

Hex. 12
3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
1 01 14 32 * 0.38 397 00 08 04 brass 8.1 08 14 32 F * 10.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 15 04 * 0.44 250 00 08 241 brass 1.5 08 15 04 * 1.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 15 15 * 0.03 14 00 08 05 brass 10.4 08 15 15 * 11.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.70
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 17

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm mm3 item material g item g
01 16 26 * 0.50 7 293 00 08 18 aluminium 10.3 08 16 26 * 13.7 1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 8 Hex. 8

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 17 12 * 0.60 213 00 08 06 brass 2.6 08 17 12 * 3.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 17 12 * 0.60 213 00 08 03 brass 9.0 08 17 13 * 9.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.71
SPECIAL VACUUM CUPS WITH SUPPORTS
3D drawings are available on vuototecnica.net

Hex. 12 Hex. 12

1 Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 18 12 * 0.63 459 00 08 67 brass 11.4 08 18 12 * 12.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber

Hex. 14 Hex. 14

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 18 12 * 0.63 459 00 08 64 brass 13.9 08 18 12 F * 14.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber

Hex. 20

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm mm3 item material g item g
01 19 31 * 0.70 5 532 00 08 09 aluminium 18.1 08 19 31 * 20.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.72
SPECIAL VACUUM CUPS WITH SUPPORTS

3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 04 * 0.78 365 00 08 242 brass 1.8 08 20 04 * 2.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 06 S 0.78 1068 00 08 243 brass 6.0 08 20 06 * 6.3
Compound: S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 08 * 0.78 804 00 08 60 brass 5.6 08 20 08 * 6.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber
Hex. 8
Hex. 8

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 11 S 0.78 784 00 08 245 brass 2.7 08 20 11 * 3.7
Compound: S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.73
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12
Hex. 12
3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 12 * 0.78 314 00 08 146 brass 9.8 08 20 12 * 10.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Hex. 12
Hex. 12
1

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 12 * 0.78 314 00 08 155 brass 9.1 08 20 12 F * 10.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 14 N 0.78 589 00 08 146 brass 9.8 08 20 14 * 11.3
Compound: N= orange colour natural rubber

Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 14 N 0.78 589 00 08 155 brass 9.1 08 20 14 F * 10.6
Compound: N= orange colour natural rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.74
SPECIAL VACUUM CUPS WITH SUPPORTS

3D drawings are available on vuototecnica.net

Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight 1
Vacuum cup item
Kg mm3 item material g item g
01 20 15 * 0.78 599 00 08 146 brass 9.8 08 20 15 * 11.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 20 15 * 0.78 599 00 08 155 brass 9.1 08 20 15 F * 10.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 20 24 * 0.78 1.9 00 08 03 brass 9.0 08 20 24 * 10.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.75
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12

Hex. 12
3D drawings are available on vuototecnica.net

1 Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 20 24 * 0.78 1.9 00 08 04 brass 8.1 08 20 24 F * 9.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 22 06 * 0.95 681 00 08 246 brass 5.0 08 22 06 * 5.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Hex. 17
Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 22 24 * 0.95 7 1.3 00 08 10 aluminium 11.0 08 22 24 * 13.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.76
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 17

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
1
Vacuum cup item
Kg mm cm3 item material g item g
01 22 45 * 0.95 7 2.7 00 08 10 aluminium 11.0 08 22 45 * 16.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Hex. 17
Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 22 99 * 0.95 7 1.7 00 08 10 aluminium 11.0 08 22 99 * 13.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 25 08 * 1.23 1.1 00 08 60 brass 5.6 08 25 08 * 7.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.77
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12 Hex. 12
3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 25 12 * 0.11 125 00 08 82 brass 11.2 08 25 12 * 12.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber

1 Hex. 12
Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 25 14 N 1.23 1.1 00 08 101 brass 10.8 08 25 14 * 12.6
Compound: N= green colour natural rubber

Vacuum cup with vulcanised support Force Volume Support Weight

Item Kg cm3 material g
08 25 22 * 1.23 1.6 steel 5.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum cup with vulcanised support Force Volume Support Weight

Item Kg cm3 material g
08 25 27 * 1.23 1.6 steel 5.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.78
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 12

3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight 1
Vacuum cup item
Kg cm3 item material g item g
01 25 28 * 1.23 3.4 00 08 03 brass 9.0 08 25 28 * 10.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Hex. 12

Hex. 12

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 25 28 * 1.23 3.4 00 08 04 brass 8.1 08 25 28 F * 9.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 26 10 * 1.33 1.1 00 08 60 brass 5.6 08 26 10 * 6.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.79
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 17

Hex. 17
3D drawings are available on vuototecnica.net

1
Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 27 24 * 1.43 2.2 00 08 15 aluminium 12.3 08 27 24 * 15.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force A Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 30 24 * 1.76 3.0 2.2 00 08 15 aluminium 12.3 08 30 24 * 15.2
01 30 24 L * 1.76 1.5 1.8 00 08 15 aluminium 12.3 08 30 24 L * 15.5

* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm3 item material g item g
01 31 12 S 1.89 991 00 08 249 brass 1.8 08 31 12 S 3.4
Compound: S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.80
SPECIAL VACUUM CUPS WITH SUPPORTS

3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 32 30 * 2.00 11.4 00 08 250 aluminium 8.6 08 32 30 * 14.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 32 36 * 2.00 3.4 00 08 19 brass 22.7 08 32 36 * 27.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
1 01 35 12 * 2.40 2.9 00 08 244 brass 5.9 08 35 12 * 8.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 40 14 * 3.14 4.8 00 08 247 brass 8.4 08 40 14 * 12.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 40 18 * 3.14 8.2 00 08 81 aluminium 8.8 08 40 18 * 15.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.82
SPECIAL VACUUM CUPS WITH SUPPORTS

Hex. 17
Hex. 17

3D drawings are available on vuototecnica.net

Force Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg cm3 item material g item g
01 40 25 * 3.14 3.4 00 08 127 aluminium 11.5 08 40 24 * 21.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; NG= yellow rubber

Hex. 12
Hex. 12
3D drawings are available on vuototecnica.net

Force Bellows stroke Volume support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm mm3 item material g item g
1 01 16 20 * 0.50 8 970 00 08 04 brass 8.1 08 16 21 F * 9.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 23 * 0.63 11 1.8 00 08 67 brass 11.4 08 18 23 * 12.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 23 * 0.63 11 1.8 00 08 64 brass 13.9 08 18 23 F * 15.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.90
SPECIAL BELLOWS CUPS WITH SUPPORTS

Hex. 14

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 23 * 0.63 11 1.8 00 08 65 brass 13.7 08 18 24 F * 15.2 1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 23 * 0.63 11 1.8 00 08 66 brass 13.5 08 18 26 F * 15.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 29 * 0.63 15 2.5 00 08 67 brass 11.4 08 18 29 * 13.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.91
SPECIAL BELLOWS CUPS WITH SUPPORTS

Hex. 14

Hex. 14
3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
1 01 18 29 * 0.63 15 2.5 00 08 64 brass 13.9 08 18 29 F * 15.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 29 * 0.63 15 2.5 00 08 65 brass 13.7 08 18 30 F * 15.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 29 * 0.63 15 2.5 00 08 66 brass 13.5 08 18 31 F * 15.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.92
SPECIAL BELLOWS CUPS WITH SUPPORTS
Hex. 12

Hex. 12

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 35 * 0.63 18 3.1 00 08 67 brass 11.4 08 18 35 * 13.7 1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 35 * 0.63 18 3.1 00 08 64 brass 13.9 08 18 35 F * 16.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 14

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 35 * 0.63 18 3.1 00 08 65 brass 13.7 08 18 36 F * 16.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.93
SPECIAL BELLOWS CUPS WITH SUPPORTS

Hex. 14

Hex. 14
3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
1 01 18 35 * 0.63 18 3.1 00 08 66 brass 13.5 08 18 37 F * 15.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 50 * 0.63 5.5 1.1 00 08 07 brass 4.8 08 18 50 * 5.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 50 * 0.63 5.5 1.1 00 08 61 brass 6.5 08 18 51 * 7.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12
Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 18 50 * 0.63 5.5 1.1 00 08 62 brass 9.4 08 18 52 * 10.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.94
SPECIAL BELLOWS CUPS WITH SUPPORTS

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 19 17 * 0.70 8 1.9 00 08 08 brass 2.7 08 19 17 * 4.0 1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 19 17 * 0.70 8 1.9 00 08 60 brass 5.6 08 19 18* 6.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 20 60 * 0.78 28 5.4 00 08 07 brass 4.8 08 20 60 * 9.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.95
SPECIAL BELLOWS CUPS WITH SUPPORTS
3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 20 60 * 0.78 28 5.4 00 08 61 brass 6.5 08 20 61 * 10.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 20 60 * 0.78 28 5.4 00 08 62 brass 4.4 08 20 62 * 8.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

3D drawings are available on vuototecnica.net

1
Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 25 35 * 1.23 10 2.5 00 08 15 aluminium 12.3 08 25 35 * 17.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum cup with vulcanised support Force Bellows stroke Volume Support Weight
Item Kg mm cm3 material g
08 25 40 * 1.23 9 4.1 steel 13.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 30 50 * 1.76 14 6.5 00 08 18 aluminium 10.3 08 30 50 * 17.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.97
SPECIAL BELLOWS CUPS WITH SUPPORTS
3D drawings are available on vuototecnica.net

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 30 50 * 1.76 14 6.5 00 08 50 aluminium 8.5 08 30 50 F * 16.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 30 99 * 1.76 14 6.5 00 08 18 aluminium 10.3 08 30 99 * 18.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

3D drawings are available on vuototecnica.net

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 30 99 * 1.76 14 6.5 00 08 50 aluminium 8.5 08 30 99 F * 16.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 30 55 * 1.76 24 10.6 00 08 18 aluminium 10.3 08 30 55 * 23.1
* Complete the code indicating the compound: N= natural para rubber; S= silicone

Hex. 17
3D drawings are available on vuototecnica.net

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 30 55 * 1.76 24 10.6 00 08 50 aluminium 8.5 08 30 55 F * 21.3
* Complete the code indicating the compound: N= natural para rubber; S= silicone

Vacuum cup with vulcanised support Force Bellows stroke Volume Support Weight
Item Kg mm cm3 material g
08 32 40 * 2.00 10 6.9 steel 14.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
1
01 33 50 * 2.13 9 12.0 00 08 82 brass 11.2 08 33 50 * 18.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17
Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 40 50 * 2.40 7 4.3 00 08 18 aluminium 10.3 08 40 50 * 14.9
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17
Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 40 50 * 2.40 7 4.3 00 08 50 aluminium 8.5 08 40 50 F * 13.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.101
SPECIAL BELLOWS CUPS WITH SUPPORTS

Hex. 12
3D drawings are available on vuototecnica.net

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 40 80 * 1.76 32 32.4 00 08 05 brass 10.0 08 40 80 * 38.7
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 40 80 * 1.76 32 32.4 00 08 14 brass 9.8 08 40 80 F * 38.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

3D drawings are available on vuototecnica.net

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 42 90 * 3.00 13 34.6 00 08 05 brass 10.0 08 42 90 * 34.5
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 12

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 42 90 * 3.00 13 34.6 00 08 14 brass 9.8 08 42 90 F * 34.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Sp20
3D drawings are available on vuototecnica.net

Sp20

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 50 70 * 4.90 28 32.2 00 08 148 aluminium 14.5 08 50 70 * 36.8
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g

01 52 50 * 5.30 13 22.7 00 08 26 aluminium 13.5 08 52 50 * 38.2

* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 50 60 A 6.60 30 92.1 00 08 466 aluminium 56 08 50 60 * 82
Compound: A= oil-resistant rubber

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g

01 80 60 A 12.56 37 145.9 00 08 466 aluminium 56 08 80 60 * 106

Compound: A= oil-resistant rubber

Hex. 17

3D drawings are available on vuototecnica.net

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 56 30 * 6.15 18 28.0 00 08 127 aluminium 11.5 08 56 30 * 28.5 1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 75 30 * 11.04 24 62.9 00 08 127 aluminium 11.5 08 75 30 * 48.1
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Hex. 17

Hex. 20

Force Bellows stroke Volume Support Support Weight Vacuum cup with support Weight
Vacuum cup item
Kg mm cm3 item material g item g
01 75 31 * 11.04 24 63.1 00 08 09 aluminium 18.1 08 75 31 * 54.7
Compound: S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.105
SUPPORTS FOR VACUUM CUPS

The supports and accessories shown and described

on this page and on the following pages are the
same as those already described in the previous
pages, alongside their respective vacuum cups. On
3D drawings are available on vuototecnica.net

these pages, the customer can also find the list of

the vacuum cups for which each support is suited.
They are specially shaped to perfectly adhere
to the internal profile of the cups and they are
provided with a male or female axial pin in order
to allow suction, as well as to fasten them to the
automation.
These cups can be manually assembled onto their
supports without any adhesives, simply by pressing
them in.
They are made with nickel-plated brass or anodised
aluminium or with special materials upon request.

Hex. 7

1
D E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 01 2.90 3 5 10 18 brass 01 04 10 4.0
01 05 10
01 06 10
00 08 02 4.75 3 5 10 18 brass 01 08 10 4.0
01 09 07

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 03 5.5 5 8 7 20 brass 01 10 10 9.0
Hex. 12
01 11 16
01 12 10
01 14 10
01 14 32
01 15 10
01 16 20
01 17 12
01 18 10
01 20 10
01 20 24
01 22 10
01 25 28

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 04 5.5 13 9 7 20 brass 01 10 10 8.1 Hex. 12

01 11 16
01 12 10
01 14 10
01 14 32
01 15 10
01 16 20
01 17 12
01 18 10
01 20 10
01 20 24
01 22 10
01 25 28

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.106
SUPPORTS FOR VACUUM CUPS

Hex. 12

3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 05 7.5 5 8 9.5 22.5 brass 01 15 15 10.0
01 25 15
01 30 15
01 40 80
01 42 90

Hex. 8
Item
D E F G H Support For vacuum cup Weight 1
Ø material item g
00 08 06 5.25 4.5 4 8.5 17 AVP 01 06 50 2.6
01 08 50
01 11 50
01 11 16
01 16 20
01 17 12

D E F H Support For vacuum cup Weight

Item
Ø material item g
00 08 07 10 5 9.5 14.5 brass 01 18 50 4.8
01 20 60

D E F H Support For vacuum cup Weight

Item
Ø material item g
00 08 08 12 4.5 10 14.5 brass 01 19 17 2.7
01 25 10
01 30 10
01 35 10

Hex. 20

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 09 16 8 14 15 37 aluminium 01 19 31 18.1
01 40 70
01 75 31

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.107
SUPPORTS FOR VACUUM CUPS

Hex. 17
3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 10 10.5 8 14 14 36 aluminium 01 22 24 11.0
01 22 45
01 22 99

1
Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 14 7.5 13 9 9.5 22.5 brass 01 25 15 9.8
01 30 15
01 40 80
01 42 90

Hex. 17

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 15 12 8 14 15 37 aluminium 01 25 35 12.3
01 27 24
01 30 24

Hex. 17

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 18 9.5 8 14 10 32 aluminium 01 16 26 10.3
01 20 30
01 30 50
01 30 55
01 30 99
01 40 50

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.108
SUPPORTS FOR VACUUM CUPS
Hex. 17

3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 19 9 5 12 18 35 brass 01 32 36 22.7

1
Hex. 17

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 20 12 8 14 10 32 aluminium 01 35 15 11.0
01 40 15
01 45 15

Hex. 17

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 21 12 17 13 10 27 aluminium 01 35 15 9.3
01 40 15
01 45 15

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 22 25 10 14 7.5 25 aluminium 01 45 10 5.9
01 60 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.109
SUPPORTS FOR VACUUM CUPS

Hex. 17
3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 24 12 8 14 12 34 aluminium 01 50 20 10.3
01 65 28

Hex. 17

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 26 14.5 8 14 13.5 35.5 aluminium 01 52 50 13.5

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 28 25 12 14 8 37.3 aluminium 01 85 10 13.4

A B D F H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 29 15.5 M12 25 18 23.5 aluminium 01 85 10 6.6

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.110
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

N O P Q Support For vacuum cup Weight
Item
material item g
00 08 31 60 25 55 20 aluminium 01 40 75 34.1 1

A d D E H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 32 60 M12 64 3 10 aluminium 01 64 15 80.6
01 65 15
01 85 15
00 08 424 60 G1/4” 64 3 10 aluminium 01 64 15 80.6
01 65 15
01 85 15

A D E H Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 33 88 92 3 11 aluminium 01 92 15 188.9
01 110 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.111
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

1 N O P Q Support For vacuum cup Weight

Item
material item g
00 08 34 107 75 102 70 aluminium 01 107 75 215.5
01 120 90

A D E H Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 35 120 127 4 15 aluminium 01 150 10 471.3

D F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 44 25 14 7.5 25 aluminium 01 45 10 5.1
01 60 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.112
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

A B D F H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 46 15.5 G1/4” 25 18 23.5 aluminium 01 85 10 6.5

Hex. 17

D E F G H Support For vacuum cup Weight

1
Item
Ø material item g
00 08 50 9.5 17 13 10 27 aluminium 01 16 26 8.5
01 30 50
01 30 55
01 30 99
01 40 50

A C D F H M Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 58 160 G3/8” 180 5 12 60 aluminium 01 180 15 740.0

N O P Q Support For vacuum cup Weight

Item
material item g
00 08 59 135 60 130 55 aluminium 01 135 60 218.4
01 150 75

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.113
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

D E F H Support For vacuum cup Weight

Item
Ø material item g
00 08 60 12 6.5 8 14.5 brass 01 19 17 5.6
01 20 08
01 20 60
01 25 08
01 25 10
01 26 10
01 30 10
01 35 10

D E F H Support For vacuum cup Weight

Item
Ø material item g
00 08 61 10 4.5 10 14.5 brass 01 18 50 6.5
01 20 60

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 62 10 13 9 3 16 brass 01 18 50 9.4
01 20 60

D E F G H Support For vacuum cup Weight

Item Hex. 14
Ø material item g
00 08 64 6.5 13 10 7.5 20.5 brass 01 14 15 13.9
01 15 23
01 18 12
01 18 23
01 18 29
01 18 35

Hex. 14
D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 65 6.5 13 M5 7.5 20.5 brass 01 14 15 13.7
01 15 23
01 18 12
01 18 23
01 18 29
01 18 35

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.114
SUPPORTS FOR VACUUM CUPS

Hex. 14

3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 66 6.5 13 M5 7.5 20.5 brass 01 14 15 13.5
01 15 23
01 18 12
01 18 23
01 18 29
01 18 35

Hex. 12
D E F G H Support For vacuum cup Weight
Item
Ø material item g
1
00 08 67 6.5 5 8 7.5 20.5 brass 01 14 15 11.4
01 15 23
01 18 12
01 18 23
01 18 29
01 18 35

A B C D E F G H N Support For vacuum cup Weight

Item
Ø Ø Ø Ø Ø material item g
00 08 68 40 M12 23 35 7 10 18 25 20 aluminium 01 46 13 47.2
00 08 72 65 G3/8” 40 60 10 15 25 35 25 aluminium 01 73 14 169.1
00 08 73 76 G3/8” 51 71 10 15 27 37 25 aluminium 01 95 14 266.0

B E F Support For vacuum cup Weight

Item
Ø material item g
00 08 70 G1/8” 8.5 6.5 aluminium 01 12 20 5.4

Fixing plate item 00 08 97

perforated TSP M3x5 screw item 00 08 103

Note: Supplied automatically also with the fixing plate and the perforated
TSP screw when ordering item 00 08 70

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.115
SUPPORTS FOR VACUUM CUPS

A B C E F Support For vacuum cup Weight

Item
Ø material item g
3D drawings are available on vuototecnica.net

00 08 71 30 G1/8” 25 8.5 6.5 aluminium 01 12 30 7.8

00 08 75 40 G1/8” 35 8.5 6.5 aluminium 01 12 40 11.4
00 08 76 55 G1/8” 50 8.5 6.5 aluminium 01 12 50 15.5

Fixing plate item 00 08 98 for supp. 00 08 71

item 00 08 99 for supp. 00 08 75
item 00 08 100 for supp. 00 08 76

2 TSP screws M3x5 item 00 08 102

Note: Supplied automatically also with the fixing plate and the
TSP screws when ordering the item relative to the support

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 81 22 8.5 14 3.5 22.5 aluminium 01 40 18 8.8
01 48 18
01 54 18

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 82 8.5 5 8 9.5 22.5 brass 01 25 12 11.2
01 33 50

F G H Support For vacuum cup Weight

Item
material item g
00 08 83 11 7.5 14.5 aluminium 01 56 15 67.4

A D Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 91 M10x1,25 25 brass 01 85 10 38.4

A D Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 92 M10 25 brass 01 45 10 5.2
01 60 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.116
SUPPORTS FOR VACUUM CUPS

Hex. 12

3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 101 9 5 8 8 21 brass 01 25 14 10.8

A B C D F H M Support For vacuum cup Weight

Item
Ø Ø Ø Ø material item g
00 08 107 120 M12 G3/8” 127 4 15 30 aluminium 01 127 15 476.9
01 150 10

RING NUT
A B C D H Ring nut For support Weight
Item
Ø Ø Ø Ø material item g
00 08 109 G1/4” 2.5 25.5 34 4.5 aluminium 00 08 108 9.8
00 08 111 G3/8” 2.5 25.5 34 4.5 aluminium 00 08 110 8.7
00 08 113 G3/8” 4.0 45.0 69 6.0 aluminium 00 08 112 58.2

SUPPORT
A D E F G H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 108 G1/4” 35 9 19.5 4.5 33.0 aluminium 01 76 24 21.4
01 90 24
01 110 24

00 08 110 G3/8” 35 9 19.5 4.5 33.0 aluminium 01 76 24 25.0

01 90 24
01 110 24

00 08 112 G3/8” 69 15 22.0 5.5 42.5 aluminium 01 150 36 73.9

Note: The ring nut is provided automatically when the support is ordered with its own item

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.117
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

A B C D E H M Support For vacuum cup Weight

Item
Ø Ø Ø Ø material item Kg
00 08 115 223 M12 G3/8” 230 5 15 70 aluminium 01 250 20 1.65
1

A B D E H M N Support For vacuum cup Weight

Item
Ø material item Kg
00 08 116 290 68 G3/8” 3 11 284 62 aluminium 01 290 68 0.53
01 300 80

A B D E H M N Support For vacuum cup Weight

Item
Ø material item Kg
00 08 117 290 140 G1/2” 3 11 284 134 aluminium 01 290 140 1.13
01 300 150

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.118
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

B D H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 118 G1/4” 40 10 aluminium 01 42 15 32.1

A B D E H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 119 120 G3/8” 127 4 15 aluminium 01 150 10 478.9

A B D E H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 123 88 G3/8” 92 3 11 aluminium 01 110 10 186.1
01 92 15

A B D E H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 126 45 M12 54 3 10 aluminium 01 75 42 45.5
01 80 20
00 08 465 45 G1/4” 54 3 10 aluminium 01 75 42 45.5
01 80 20
00 08 193 45 G3/8” 54 3 10 aluminium 01 75 42 45.5
01 80 20
00 08 143 45 G1/2” 54 3 10 aluminium 01 75 42 45.5
01 80 20

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.119
SUPPORTS FOR VACUUM CUPS

Hex. 17
3D drawings are available on vuototecnica.net

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 127 13.5 8 14 15 37 aluminium 01 30 45 11.5
01 40 25
01 44 30
01 56 30
01 75 30

1
Sp13

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 132 8.5 12 8 5 17 aluminium 01 20 23 3.8
01 22 19
01 34 26

Sp13

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 133 8.5 5.5 8 5 18.5 aluminium 01 20 23 3.5
01 22 19
01 34 26

Sp17

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 134 10 14 10 7.5 21.5 aluminium 01 30 32 8.3
01 40 42
01 43 28

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.120
SUPPORTS FOR VACUUM CUPS

Sp17

3D drawings are available on vuototecnica.net

E F G H Support For vacuum cup Weight
Item
material item g
00 08 135 7.5 12 7.5 27 aluminium 01 30 32 9.5
01 40 42
01 43 28

E F G H Support For vacuum cup Weight

Item
material item g
00 08 136 12 14 8 37.3 aluminium 01 85 10 9.2

Sp22

E F G H Support For vacuum cup Weight

Item
material item g
00 08 141 14 10 9.5 23.5 aluminium 01 50 53 19.7
01 53 35

Sp22

E F G H Support For vacuum cup Weight

Item
material item g
00 08 142 7.5 12 9.5 29 aluminium 01 50 53 15.7
01 53 35

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.121
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

N O P Q Support For vacuum cup Weight

Item
material item g
00 08 144 135 50 130 45 aluminium 01 135 50 176.1
01 150 65

A B C D E H M Support For vacuum cup Weight

Item
Ø Ø Ø Ø material item g
00 08 145 120 G3/8” G3/8” 127 4 15 27 aluminium 01 150 10 471.9

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 146 8 5 8 5 18 brass 01 20 12 9.8
01 20 14
01 20 15

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.122
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

B D H Support For vacuum cup Weight
Item
Ø Ø material item g
00 08 147 M12 40 10 aluminium 01 42 15 32.8

Sp20
1

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 148 12 7.5 12 15 34.5 aluminium 01 50 70 14.5

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 155 8 13 9 5 18 brass 01 20 12 9.1
01 20 14
01 20 15

A C D E N H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 162 61 G1/8” 70 3 23 10 aluminium 01 110 58 78.9

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.123
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

A B C D E N H Support For vacuum cup Weight

Item
Ø Ø Ø Ø material item g
00 08 163 98 G1/2” G1/8” 107 3 35 10 aluminium 01 150 74 211.8

Hex. 17

1
C E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 172 M8 8 14 15 37 aluminium 01 40 25 15.2
01 56 30
01 75 30

Hex. 13
C E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 173 5.5 5 8 7.5 20.5 aluminium 01 15 23 8.7
01 18 23
01 18 29
01 18 35

4 seats for TCCE Non-slip plastic

M4 screw coating
Filter

O-ring

N O P Q Support For vacuum cup Weight

Item
material item g
00 08 184 60 25 55 20 aluminium 01 40 75 38.7

A B D E F H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 231 15 G1/8” 36 10 4 14 aluminium 01 31 06 24.9

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.124
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

A B D E F H Support For vacuum cup Weight
Item
Ø Ø Ø material item g
00 08 232 15 G1/8” 30 10 4 14 aluminium 01 24 06 16.7

A B D E H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 233 60 G3/4” 64 3 10 aluminium 01 85 15 77.3
00 08 234 60 G1/2” 64 3 10 aluminium 01 85 15 78.3

Hex. 8

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 236 8 5 5 5 15 brass 01 07 13 3.0

Hex. 8
D E F G H Support For vacuum cup Weight
Item
Ø material item g
00 08 237 6 5 5 4 14 brass 01 08 07 3.0

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 238 5.7 7 7 6 20 brass 01 11 08 7.0

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 239 4 5 8 6.5 19.5 brass 01 14 09 8.0

Hex. 12

D E F G H Support For vacuum cup Weight

Item
Ø material item g
00 08 240 4 13 9 6.5 19.5 brass 01 14 09 7.0

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.125
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

D F H Support For vacuum cup Weight

Item
Ø material item g
00 08 241 8 9 10 brass 01 15 04 1.5

D F H Support For vacuum cup Weight

Item
Ø material item g
00 08 242 11 9 9.5 brass 01 20 04 1.8

D F H Support For vacuum cup Weight

Item
Ø material item g
00 08 243 15 10 13 brass 01 20 06 6.0

D E F H Support For vacuum cup Weight

Item
Ø material item g
00 08 244 14 6.5 8 14.5 brass 01 35 12 5.9

Hex. 8

D E F G H Support For vacuum cup

Item
Ø material item g
00 08 245 6.5 4.5 6 8 18.5 brass 01 20 11 2.7

D F H Support For vacuum cup Weight

Item
Ø material item g
00 08 246 14 8 10 brass 01 22 06 5.0

D F H Support For vacuum cup Weight

Item
Ø material item g
00 08 247 14 8 17 brass 01 40 14 8.4

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.126
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

D F H Support For vacuum cup Weight
Item
Ø material item g
00 08 248 24 14 23.5 aluminium 01 54 18 5.8

D E F H Support For vacuum cup Weight

Item
Ø material item g
00 08 249 8 8.5 5 13.5 brass 01 31 12 S 1.8

D F H Support For vacuum cup Weight

Item
Ø material item g
00 08 250 21 14 23 aluminium 01 32 30 8.6

Non-slip
plastic
coating

4 seats for Filter O-ring

TCCE M4 screw

A B C H N O P Q Support For vacuum cup Weight

Item
material item g
00 08 256 80 51 2.5 16.6 107 75 102 70 aluminium 01 120 90 244.5

Non-slip
plastic
coating

4 seats for Filter O-ring

TCCE M4 screw

A B C H N O P Q Support For vacuum cup Weight

Item
material item g
00 08 257 110 35 2.3 16.4 135 60 130 55 aluminium 01 150 75 247.9

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.127
SUPPORTS FOR VACUUM CUPS
3D drawings are available on vuototecnica.net

A B C D E H Support For vacuum cup Weight

Item
Ø Ø Ø Ø material item g
00 08 280 35 G1/2” -- 70 12.5 22.5 aluminium 01 150 55 120
00 08 281 65 G1/2” -- 130 12.5 23.5 aluminium 01 210 60 465
00 08 286 35 -- 8 70 12.5 22.5 aluminium 01 150 55 125
00 08 287 65 -- 8 130 12.5 23.5 aluminium 01 210 60 470

A B D E F G H Support For vacuum cup Weight

Item
Ø Ø material item g
Hex. B
00 08 343 G1/8” 14 7.3 10 8.0 5.5 15.5 aluminium VOP 08 24 SR 16.8
VOP 10 30 SR
VOP 12 36 SR
screw
00 08 345 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOP 15 45 SR 19.9
item 00 08 347 for supp.00 08 403
00 08 405 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOP 20 60 SR 24.7
VOP 25 75 SR item 00 08 348 for supp.00 08 405
00 08 403 G1/4” 17 13.0 12 8.5 9.0 21.0 aluminium VOP 28 85 SR 25.6
Note: Supplied automatically also with the screw
VOP 35 100 SR
when ordering the item relative to the support

A B D E F G H Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 344 G1/8” 14 7.3 7 7 5.5 19.5 aluminium VOP 08 24 SR 18.5 Hex. B
VOP 10 30 SR
VOP 12 36 SR
screw
00 08 346 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOP 15 45 SR 25.0
00 08 404 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOP 20 60 SR 29.8 item 00 08 347 for supp.00 08 402
VOP 25 75 SR item 00 08 348 for supp.00 08 404
00 08 402 G1/4” 17 13.0 8 8 9.0 25.0 aluminium VOP 28 85 SR 30.7
Note: Supplied automatically also with the screw
VOP 35 100 SR
when ordering the item relative to the support

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.128
SUPPORTS FOR VACUUM CUPS

3D drawings are available on vuototecnica.net

Sp B

B C D E F G H I L Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 373 8 G1/4” G1/4” 2 10 10.0 22.0 M8 11 aluminium 08 75 43 SR 4.1
00 08 372 8 G3/8” G1/4” 2 13 10.0 25.0 M8 11 aluminium 08 75 43 SR 7.4
00 08 376 8 G3/8” G3/8” 3 13 15.5 31.5 M8 11 aluminium 08 110 73 SR 14.1
00 08 375 8 G1/2” G3/8” 3 13 15.5 31.5 M8 11 aluminium 08 110 73 SR 15.5

Sp B

B C D E F G H I L M Support For vacuum cup Weight

Item
Ø Ø material item g
00 08 374 22 G3/8” G1/4” 1.5 14 10.0 25.0 M8 10 11 aluminium 08 75 43 SR 12.0
00 08 377 23 G1/2” G3/8” 3.0 17 15.5 35.5 M8 13 11 aluminium 08 110 73 SR 17.8

Sp B

A B C D E F G H I L Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 394 20 17 G1/8” 11 6.0 8 7.2 21.2 M5 8 aluminium 01 35 27 6.2
00 08 395 27 20 G1/8” 15 7.5 8 9.2 24.7 M5 8 aluminium 01 52 40 13.2
00 08 366 20 17 G1/4” 11 6.0 8 7.2 21.2 M8 11 aluminium 01 35 27 6.1
00 08 364 27 20 G1/4” 15 7.5 8 9.2 24.7 M8 11 aluminium 01 52 40 13.0

Sp B

A B C D E F G H Support For vacuum cup Weight

Item
Ø Ø Ø material item g
00 08 396 20 17 G1/8” 11 14 8 7.2 21.2 aluminium 01 35 27 9.7
00 08 397 27 20 G1/8” 15 14 8 9.2 23.2 aluminium 01 52 40 20.0
00 08 392 20 17 G1/4” 11 14 10 7.2 21.2 aluminium 01 35 27 7.8
00 08 393 27 20 G1/4” 15 14 10 9.2 23.2 aluminium 01 52 40 18.1

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.129
GAS - NPT ADAPTERS

These adapters allow using NPT threaded fittings

on vacuum components with NPT threading, such
as vacuum components like vacuum cup supports,
valves and solenoid valves, filters etc. with gas
3D drawings are available on vuototecnica.net

threading.

Hex. T

FEMALE GAS - MALE NPT ADAPTER

A D E F H T Adapter Weight
Item
Ø Ø material g
00 08 259 1/8” NPT G1/8” 10 12 22 14 brass 14
00 08 260 1/4” NPT G1/4” 12 17 29 19 brass 34
00 08 261 3/8” NPT G3/8” 16 18 34 22 brass 48
00 08 262 1/2” NPT G1/2” 17 19 36 27 brass 72
00 08 263 3/4” NPT G3/4” 19 20 39 32 brass 100
00 08 264 1” NPT G1” 22 20 42 41 brass 176
00 08 265 1” 1/4 NPT G1” 1/4 23 23 46 50 brass 274
00 08 266 1” 1/2 NPT G1” 1/2 23 23 46 60 brass 470
00 08 267 2” NPT G2” 25 24 49 70 brass 506
Note: All adapters are manufactured per minimum batch sizes and with cost evaluated upon final balance.

Hex. T

MALE GAS - FEMALE NPT ADAPTER

A D E F H T Adapter Weight
Item
Ø Ø material g
00 08 268 G1/8” 1/8” NPT 10 15 25 14 brass 16
00 08 269 G1/4” 1/4” NPT 11 17 28 19 brass 34
00 08 270 G3/8” 3/8” NPT 12 22 34 22 brass 52
00 08 271 G1/2” 1/2” NPT 14 23 37 27 brass 78
00 08 272 G3/4” 3/4” NPT 14 24 38 32 brass 110
00 08 273 G1” 1” NPT 17 28 45 41 brass 224
00 08 274 G1” 1/4 1” 1/4 NPT 18 28 46 50 brass 290
00 08 275 G1” 1/2 1” 1/2 NPT 19 29 48 60 brass 476
00 08 276 G2” 2” NPT 20 31 51 70 brass 550
Note: All adapters are manufactured per minimum batch sizes and with cost evaluated upon final balance.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.130
THREADED GRUB SCREWS WITH CALIBRATED HOLE

These threaded grub screws with calibrated hole are

used to reduce the cup suction section, thus reducing
vacuum losses in case the cup fails to grip.
They are made of brass and can be inserted in all the cup

3D drawings are available on vuototecnica.net

supports set for this application.

A D F H Grub screw Weight

Item
Ø Ø material g
00 08 122 M8 0.9 5 11 brass 2.5
00 08 121 M8 1.2 5 11 brass 2.4
00 08 120 M8 1.5 5 11 brass 2.3

A D F H Grub screw Weight

Item
Ø Ø material g
00 08 164 G1/8” 1.2 5 7 brass 3.0
00 08 165 G1/8” 1.5 5 7 brass 3.0
1
00 08 176 G1/4” 1.2 5 10 brass 4.0
00 08 334 G1/8” 3.0 4 7 brass 4.0

ADAPTERS

These standard accessories offer the user different

assembly options.
The galvanised steel or brass adapters screwed onto
the standard vacuum cup support connections can
vary the threads from gas to metric or vice-versa, from
male to female or vice-versa, in addition of course to
increasing or decreasing the size of their threaded
diameter.

MF ADAPTER
D d H Support Weight
Item
Ø Ø material g
00 08 130 G1/4” M10 14 steel 4.0
00 08 131 G3/8” M10 14 steel 12.0
00 08 230 G3/8” G1/4” 14 steel 6.0
00 08 254 1/4” NPT M10 14 steel 3.9
00 08 255 3/8” NPT M10 14 steel 11.9
00 08 258 3/8” NPT G1/4” 14 steel 5.9
Hex. 20

Hex. 20

MM AND MF ADAPTER
D d E F G H Adapter Weight
Item
Ø Ø material g
00 08 129 M12 G1/4” 15 14 11 40 brass 58.0
00 08 296 M12 G3/8” 18 -- 10 28 brass 34.0
00 08 297 G1/4” M12 16 -- 11 27 brass 40.0

Item 00 08 129 Item 00 08 296

Item 00 08 297
Hex. 20
FF ADAPTER FOR JOINT COUPLINGS GS
D E F G H Adapter Weight
Item
Ø Ø material g
00 08 54 M10 13 13.5 M5 36 brass 72
00 08 251 M8 16 15.0 G1/8” 48 brass 102
00 08 252 M12 16 15.0 G1/8” 48 brass 90

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
1.131
VACUUM CUP ADAPTERS
3D drawings are available on vuototecnica.net

MF ADAPTER
D d F H SW Weight
Item
Ø Ø g
00 08 215 G3/8” G1/4” 8 14 6 11.5

MF ADAPTER
D d F H SW Weight
Item
Ø Ø g
00 08 216 G3/8” G1/4” 8 11.5 6 6.0

MM ADAPTER
D d E F SW Weight
Item
Ø Ø g
00 08 217 G1/4” G1/4” 15 10 6 16.7
00 08 218 G1/4” M10 x 1.5 15 12 6 10.2
00 08 219 G1/4” M14 x 1.5 15 12 6 16.0
00 08 220 G3/8” G1/4” 14 10 6 18.4
00 08 221 G3/8” M10 x 1.5 14 12 6 16.3
00 08 222 G3/8” M14 x 1.5 14 12 6 22.5

MM ADAPTER
D d E F SW Weight
Item
Ø Ø g
00 08 223 G1/4” G1/4” 11.5 10 6 13.9
00 08 224 G1/4” M10 x 1.5 13.0 12 6 10.1
00 08 225 G1/4” M14 x 1.5 13.0 12 6 15.8
00 08 226 G3/8” G1/4” 10.5 11 6 16.6
00 08 227 G3/8” M10 x 1.5 10.5 13 6 14.2
00 08 228 G3/8” M14 x 1.5 10.5 13 6 20.2

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.132
SELF-LOCKING VACUUM CUPS WITH TRACTION RELEASE

These cups do not require a connection to any vacuum source, since

the object onto which they are laid on evacuates the air inside them.
A built-in non-return valve prevents the air from entering again, thus
maintaining the vacuum.

3D drawings are available on vuototecnica.net

To release the piece, simply lift it a few millimetres, thus opening the
non-return valve, which restores the atmospheric pressure inside the
cup, by letting the air in.
Since possible losses cannot be recovered, these cups a
recommended only for holding objects with smooth and
impermeable surfaces, such as glass, polished sheets, and other
similar objects. They are particularly suited for glass carrying
trolleys feeding trolleys for robotic systems.
They are made with nickel-plated brass with a steel drive bush,
which can be provided in the anti-rotation version upon request.

VACUUM CUPS WITH FEMALE VULCANISED SUPPORT, SPARE PART

Volume A B D E G H Support Weight
Item
cm3 Ø Ø Ø material g
08 50 40 * 9.8 31 G3/8” 50 16.0 6.5 29.0 steel 38.5
08 75 40 * 27.8 31 G3/8” 75 25.0 9.0 38.0 steel 57.9
08 100 40 * 41.3 32 G3/8” 100 26.0 9.0 39.0 steel 78.3
08 100 50 * 70.3 32 G3/8” 100 30.5 15.0 43.5 steel 74.8
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone

Vacuum
cup

Sp25

Ring nuts KM6

Sp25

SELF-LOCKING VACUUM CUPS WITH TRACTION RELEASE

Force -10 kPa D E H Vacuum cup Weight
Item
Kg Ø item g
17 50 40 * 1.90 50 16 90 08 50 40 436
17 75 40 * 4.42 75 25 99 08 75 40 458
17 100 40 * 7.85 100 26 100 08 100 40 474
17 100 50 * 7.85 100 30 104 08 100 50 473
* Complete the code indicating the compound: B= BENZ rubber; N= natural para rubber; S = silicone
Note: The suction cup force shown in the table is calculated at a hypothetical vacuum value of -10 kPa.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.133
SELF-LOCKING VACUUM CUPS WITH TRACTION RELEASE
3D drawings are available on vuototecnica.net

VACUUM CUPS WITH SUPPORT, SPARE PART

Volume A B D E G H Vacuum cup Support Support Weight
Item
cm3 Ø Ø Ø item item material g
08 60 10 * 16.1 15 G1/4” 60 22 9.5 36 01 60 10 00 08 22 aluminium 20.8
08 85 10 * 48.8 25 G1/4” 85 41 14.0 55 01 85 10 00 08 28 aluminium 49.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum
cup

Sp25

Ring nuts KM6

Sp25

SELF-LOCKING VACUUM CUPS WITH TRACTION RELEASE

Force -10 kPa D E H Vacuum cup Weight
Item
Kg Ø item g
17 60 10 * 2.9 60 22 96 08 60 10 415
17 85 10 * 5.7 85 41 115 08 85 10 444
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The suction cup force shown in the table is calculated at a hypothetical vacuum value of -10 kPa.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.134
BUILT-IN VACUUM CUPS WITH BALL VALVE

The main feature of these cups is that they open,

and therefore they produce a vacuum, only when
the load to be handled activates the sealing ball.
In this version, the gripping surface is limited by a

3D drawings are available on vuototecnica.net

silicone O-ring which guarantees the vacuum seal.
They have been specially designed for vacuum beds
and they are fully made with anodised aluminium.

O-ring

Ring nuts KM7

Sp 30

Sp 17

BUILT-IN VACUUM CUPS WITH BALL VALVE

Force Volume B d D E F G H I O-ring Weight
Item
Kg cm3 Ø Ø Ø item g
05 01 10 9.80 2.1 35 x 1.5 50 59 9 3 27 66 27 00 05 14 248
05 02 10 13.60 3.0 35 x 1.5 59 68 9 3 27 66 27 00 05 15 268
05 03 10 18.10 3.9 35 x 1.5 68 77 9 3 27 66 27 00 05 16 294
05 04 10 29.70 6.3 35 x 1.5 87 96 9 3 27 66 27 00 05 19 358

The main feature of the these cups is the same as

described above; they differ only in the seal which, in
these, consists of the flat vacuum cups listed in the
table.
3D drawings are available on vuototecnica.net

They are especially designed for the glass industry

vacuum and in all those cases where the use of a
magnetic plane is not possible.
They are made of anodised aluminium but can be
manufactured with other metals upon request.

SPARE VACUUM CUP

Force Volume A B C D E F H N Weight
Item
Kg cm3 Ø Ø Ø Ø Ø g
01 65 15 * 8.29 9.1 68 63 59 65 3 7 17 27 21.4
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum
cup

Ring nuts

Sp 17

BUILT-IN VACUUM CUPS WITH BALL VALVE

Force A B C D E H M Ring nut Vacuum cup Weight
Item
Kg Ø Ø Ø Ø item g
05 65 15 * 8.29 69 25 x 1.5 40 65 19 80 22 KM 5 01 65 15 262
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

3D drawings are available on vuototecnica.net

SPARE VACUUM CUPS

Force Volume A B C D E F H N Weight
Item
Kg cm3 Ø Ø Ø Ø Ø g
01 85 15 * 14.18 13.0 68 63 59 85 3 7 17 27 29.7
01 110 10 * 23.74 24.9 96 91 87 114 3 8 17 54 44.3
01 150 10 * 45.00 75.7 133 125 118 154 4 11 23 64 112.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum
cup

Ring
nuts

Sp 17

BUILT-IN VACUUM CUPS WITH BALL VALVE

Force A B C D E H M Ring nut Vacuum cup Weight
Item
Kg Ø Ø Ø Ø item g
05 85 15 * 14.18 69 25 x 1.5 40 85 19 80 22 KM 5 01 85 15 272
05 110 10 * 23.74 97 25 x 1.5 40 114 19 80 22 KM 5 01 110 10 422
05 150 10 * 45.00 135 35 x 1.5 80 154 25 86 32 KM 7 01 150 10 894
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Their main feature is that they open suction and therefore they
produce a vacuum, only when the load to be handled activates the
sealing ball.
Especially designed for the vacuum operated beds of woodworking
3D drawings are available on vuototecnica.net

machines, they differ from the previously described ones because of

the high precision of their cylindrical support, which is ground to size,
and because of their square closing block, which prevents the cup
from rotating and enables connection to vacuum.
The cold fitted cups are the flat ones listed in the table, in the various
compounds.
The support of these cups is made of anodised aluminium, while the
closing block is made of brass.

SPARE VACUUM CUP

Vacuum
cup

SPECIAL BUILT-IN VACUUM CUP WITH BALL VALVE

Force A B C D E F G H M Vacuum cup Weight
Item
Kg Ø Ø Ø Ø item g
05 65 15 M * 8.29 69 40 M5 65 19 31.5 16.0 51.5 20 01 65 15 456
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

3D drawings are available on vuototecnica.net

SPARE VACUUM CUP

Vacuum
cup

SPECIAL BUILT-IN VACUUM CUP WITH BALL VALVE

Force A B D E F G H Vacuum cup Weight
Item
Kg Ø Ø Ø item g
05 65 65 * 8.29 69 40 65 19 47.5 14.5 67.5 01 65 15 528
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.139
SPECIAL BUILT-IN VACUUM CUPS WITH BALL VALVE
3D drawings are available on vuototecnica.net

SPARE VACUUM CUPS

Force Volume A B C D E F H N Weight
Item
Kg cm3 Ø Ø Ø Ø Ø g
01 85 15 * 14.18 13.0 68 63 59 85 3 7 17 27 29.7
01 110 10 * 23.74 24.9 96 91 87 114 3 8 17 54 44.3
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum
cup

SPECIAL BUILT-IN VACUUM CUPS WITH BALL VALVE

Force A B C D E F G H M Vacuum cup Weight
Item
Kg Ø Ø Ø Ø item g
05 85 15 M * 14.18 69 40 M5 85 19 31.5 16.0 51.5 20 01 85 15 466
05 110 10 M * 23.74 97 40 M5 114 19 32.0 16.0 52.0 20 01 110 10 614
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

3D drawings are available on vuototecnica.net

SPARE VACUUM CUPS

Vacuum
cup

SPECIAL BUILT-IN VACUUM CUPS WITH BALL VALVE

Force A B D E F G H Vacuum cup Weight
Item
Kg Ø Ø Ø item g
05 85 65 * 14.18 69 40 85 19 47.5 14.5 67.5 01 85 15 536
05 110 65 * 23.74 97 40 114 19 48.0 14.5 68.0 01 110 10 674
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.141
SUPPORTS WITH RETRACTABLE STRIKING PIN

These supports with retractable striking pins have been designed to

allow a quick centring of the load to be clamped to the machine work
surface via the cups.
The striking pin is solidly connected to a piston and it is activated by
3D drawings are available on vuototecnica.net

the vacuum while retracting and while remaining in its housing and
also by a stainless steel spring while coming out.
These supports are mechanically fixed to the work surface.
The striking pin is made of plastic material, while the support is made
of anodised aluminium.
They are supplied standard with a quick coupling for vacuum
connection.

Glass plate

Work Surface

Support with retractable Round vacuum cup with ball

striking pin valve and self-locking support

For Ø 8 ext. hose

SUPPORTS WITH RETRACTABLE STRIKING PIN

A B C D E F G H Weight
Item
Ø Ø Ø Kg
23 01 10 80 30 53 110 18 45 12 63 0.690
23 01 15 80 30 53 110 18 64 12 99 0.846
23 02 10 80 30 53 110 18 75 12 110 0.956
23 05 10 80 30 53 110 18 110 12 180 1.280

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.142
ROUND VACUUM CUPS WITH SELF-LOCKING SUPPORT

These cups represent a true mobile clamping

system. They are composed of:
- A sturdy anodised aluminium support with a
wide surface at the base limited by a seal whose

3D drawings are available on vuototecnica.net

purpose is to fix it to the bearing surface.
- A standard circular flat cup which is cold fitted
onto the upper part of the support for gripping the
load.
- Two quick couplings for vacuum connection.
The detection of vacuum for gripping and releasing
the support from the bearing surface and gripping
and releasing the load can be made via three-way
vacuum valves or solenoid valves.
All cups with self-locking support of this and other
ranges with the gripping plane at the same height
can be used simultaneously, even if they are of
different types or have different sizes.

SPARE VACUUM CUPS

Vacuum
cup
Gripping surface

For Ø 6 int. hose

O-ring

VACUUM CUPS WITH SELF-LOCKING SUPPORT

Force A B C D E F G H Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
16 85 15 * 14.5 98 60 41 85 17 49.0 56.0 54.5 01 85 15 00 16 06 0.542
16 110 10 * 24.0 125 88 58 114 17 50.0 56.0 54.5 01 110 10 00 16 07 1.056
16 150 10 * 45.0 165 120 76 154 23 49.5 57.5 54.5 01 150 10 00 16 08 1.858
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.143
RECTANGULAR VACUUM CUPS WITH SELF-LOCKING SUPPORT

These cups represent a true mobile clamping

system. They are composed of:
- A sturdy anodised aluminium support with a
wide surface at the base limited by a seal whose
3D drawings are available on vuototecnica.net

purpose is to fix it to the bearing surface.

- A standard rectangular flat cup which is cold fitted
onto the upper part of the support for gripping the
load.
- Two quick couplings for vacuum connection.
The detection of vacuum, for gripping and releasing
the support, can be made via three-way vacuum
valves or solenoid valves.
All cups with self-locking support of this and other
ranges with the gripping plane at the same height
can be used simultaneously, even if they are of
different types or have different sizes.

SPARE VACUUM CUPS

Force Volume A B E F G H L M N O P Q Weight
Item
Kg cm3 g
01 40 75 * 6.7 9.2 64 29 3 7.5 6.5 16.0 75 40 59 24 54 19 15.6
01 120 90 * 24.0 42.9 107 78 3 7.5 7.5 17.5 117 87 102 73 97 68 38.8
01 150 75 * 25.0 43.5 137 62 3 7.5 7.5 16.5 147 72 132 57 127 52 41.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum
cup
Gripping surface

For Ø 6 int. hose

O-ring

VACUUM CUPS WITH SELF-LOCKING SUPPORT

Force A B C D E F G H I L M N Vacuum cup O-ring Weight
Item
Kg item item Kg
16 40 75 * 6.7 41 76 48 83 16.0 51 56.5 54.5 30.5 55 26.5 20 01 40 75 00 05 16 0.260
16 120 90 * 24.0 90 120 98 128 17.5 50 57.0 54.5 56.0 102 49.0 70 01 120 90 00 16 10 1.166
16 150 75 * 25.0 75 150 83 144 16.5 50 57.0 54.5 48.0 130 57.0 55 01 150 75 00 16 10 1.177
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.144
ROUND VACUUM CUPS WITH BALL VALVE
AND SELF-LOCKING SUPPORT
These cups represent a true mobile clamping system. They are
composed of:
- A sturdy anodised aluminium support with a wide surface at the
base limited by a seal whose purpose is to fix it to the bearing

3D drawings are available on vuototecnica.net

surface.
- A standard circular flat cup which is cold fitted onto the upper part of
the support for gripping the load.
- A ball valve that opens up creating vacuum, only when activated by
the load to be gripped.
- Two quick couplings for vacuum connection.
The detection of vacuum, for gripping and releasing the support, can
be made via three-way vacuum valves or solenoid valves.
All cups with self-locking support of this and other ranges with the
gripping plane at the same height can be used simultaneously, even if
they are of different types or have different sizes.

SPARE VACUUM CUPS

Vacuum
cup
Gripping surface

For Ø 6 int. hose

O-ring

VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT

Force A B C D E F G H I Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
18 85 15 * 14.5 98 60 41 85 17 49.0 56.0 54.5 1 01 85 15 00 16 06 0.580
18 110 10 * 24.0 125 88 58 114 17 50.0 56.0 54.5 1 01 110 10 00 16 07 1.106
18 150 10 * 45.0 165 120 76 154 23 49.5 57.5 54.5 1 01 150 10 00 16 08 1.926
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.145
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND
SELF-LOCKING SUPPORT
These cups represent a true mobile clamping system. They are
composed of:
- A sturdy anodised aluminium support with a wide surface at the
base limited by a seal whose purpose is to fix it to the bearing
3D drawings are available on vuototecnica.net

surface.
- A standard rectangular flat cup which is cold fitted onto
the upper part of the support for gripping the load.
- A ball valve that opens up creating vacuum, only
when activated by the load to be gripped.
- Two quick couplings for vacuum connection.
The detection of vacuum, for gripping and releasing
the support, can be made via three-way vacuum
valves or solenoid valves.
All cups with self-locking support of this and other
ranges with the gripping plane at the same height can
be used simultaneously, even if they are of different types
or have different sizes.

SPARE VACUUM CUPS

Force Volume A B E F G H L M N O P Q Weight
Item
Kg cm3 g
01 40 75 * 6.7 9.2 64 29 3 7.5 6.5 16.0 75 40 59 24 54 19 15.6
01 120 90 * 24.0 42.9 107 78 3 7.5 7.5 17.5 117 87 102 73 97 68 38.8
01 150 75 * 25.0 43.5 137 62 3 7.5 7.5 16.5 147 72 132 57 127 52 41.2
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Vacuum
cup
Gripping surface

For Ø 6 int. hose

O-ring

VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT

Force A B C D E F G I L M N O P Vacuum cup O-ring Weight
Item
Kg item item Kg
18 40 75 * 6.7 41 76 48 83 16.0 51 56.5 41.5 55 26.5 15.0 2 21.0 01 40 75 00 05 16 0.352
18 120 90 * 24.0 90 120 98 128 17.5 50 57.0 56.0 102 49.0 35.0 1 35.0 01 120 90 00 16 10 1.224
18 150 75 * 25.0 75 150 83 144 16.5 50 57.0 48.0 130 57.0 27.5 1 27.5 01 150 75 00 16 10 1.194
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.146
ROUND VACUUM CUPS WITH BALL VALVE
AND SELF-LOCKING SUPPORT
These cups represent a true mobile clamping system.
They are composed of:
- A sturdy aluminium support with a wide surface at the base limited by a seal whose
purpose is to fix it to the bearing surface.

3D drawings are available on vuototecnica.net

- A standard circular flat cup which is cold fitted onto the upper part of the support for
gripping the load.
- A ball valve that opens up creating vacuum, only when activated by the load to be
gripped.
- Two quick couplings for vacuum connection.
The gripping plane of these cups is covered with a special non-slip plastic coating, which
is particularly suited for clamping glass and smooth marble.
The detection of vacuum, for gripping and releasing the support, can be made via three-
way vacuum valves or solenoid valves.
All cups with self-locking support of this and other ranges with the gripping plane at
the same height can be used simultaneously, even if they are of different types or have
different sizes.
Note: Available with support for mechanical fixing with code 28, instead of 18.

SPARE VACUUM CUPS

Force Volume A B C D E F H N Weight
Item
Kg cm3 Ø Ø Ø Ø Ø g
01 85 15 M * 14.18 13.0 68 63 59 85 3 7 17 53 26.2
01 110 10 M * 23.74 24.9 96 91 87 114 3 8 17 80 40.1
01 150 10 M * 45.00 75.7 133 125 118 154 4 11 23 117 98.3
01 250 20 * 122.60 200.0 235 227 220 254 4 11 23 220 188.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond

Vacuum
Non-slip plastic coating cup
Gripping surface

For Ø 8 ext. hose

O-ring

VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT

Force A B C D F G I L M Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
18 85 15/90 MT * 14.18 60 98 42 85 17 85.0 1 30 12 01 85 15 M 00 16 06 0.880
18 110 10/90 MT * 23.74 88 125 51 114 17 85.5 1 30 12 01 110 10 M 00 16 07 1.704
18 150 10/90 MT * 45.00 120 165 68 154 23 85.0 1 30 12 01 150 10 M 00 16 08 3.158
18 250 20/90 MT * 122.60 223 270 121 254 23 85.0 1 33 15 01 250 20 00 18 09 10.322
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.147
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND
SELF-LOCKING SUPPORT
These cups represent a true mobile clamping system.
They are composed of:
- A sturdy aluminium support with a wide surface at the base limited by a seal
whose purpose is to fix it to the bearing surface.
3D drawings are available on vuototecnica.net

- A standard rectangular flat cup which is cold fitted onto the upper part of the
support for gripping the load.
- A ball valve that opens up creating vacuum, only when activated by the load to be
gripped.
- Two quick couplings for vacuum connection.
The gripping plane of these cups is covered with a special non-slip plastic coating,
which is particularly suited for clamping glass and smooth marble.
The detection of vacuum, for gripping and releasing the support, can be made via
three-way vacuum valves or solenoid valves.
All cups with self-locking support of this and other ranges with the gripping plane
at the same height can be used simultaneously, even if they are of different types
or have different sizes.
Note: Available with support for mechanical fixing with code 28, instead of 18.

SPARE VACUUM CUPS

Force Volume A B E F G H L M N O P Q Weight
Item
Kg cm3 g
01 40 75 * 6.7 9.2 64 29 3 7.5 6.5 16.0 75 40 59 24 54 19 15.6
01 120 90 * 24.0 42.9 107 78 3 7.5 7.5 17.5 117 87 102 73 97 68 38.8
01 150 75 * 25.0 43.5 137 62 3 7.5 7.5 16.5 147 72 132 57 127 52 41.2
01 300 80 * 60.0 117.6 288 68 3 7.5 7.5 17.5 297 77 284 64 278 58 80.0
01 300 150 * 113.0 268.5 288 138 3 7.5 7.5 17.5 297 147 284 134 278 128 90.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond

Non-slip plastic Vacuum

coating cup
Gripping surface

For Ø 8 ext. hose

O-ring

VACUUM CUPS WITH BALL VALVE AND SELF-LOCKING SUPPORT

Force A B C D E F G I L M N O P Q R Vacuum cup O-ring Weight
Item
Kg item item Kg
18 40 75/90 MT * 6.7 41 76 48 83 16.0 55 92.0 2 86.5 26.5 37.0 21.0 15.0 30 17 01 40 75 00 05 16 0.570
18 120 90/90 MT * 24.0 90 120 98 128 17.5 102 92.5 1 85.5 49.0 51.0 35.0 35.0 30 12 01 120 90 00 16 10 1.898
18 150 75/90 MT * 25.0 75 150 83 144 16.5 130 92.5 1 85.5 57.0 43.5 27.5 27.5 30 12 01 150 75 00 16 10 1.924
18 300 80/90 MT * 60.0 80 300 90 310 17.5 284 92.5 1 85.5 140.0 47.0 31.0 31.0 33 15 01 300 80 00 18 10 4.632
18 300 150/90 MT * 113.0 150 300 160 310 17.5 284 92.5 1 85.5 140.0 83.0 67.0 67.0 33 15 01 300 150 00 18 11 9.534
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.148
ROUND VACUUM CUPS WITH BALL VALVE
AND HIGH SELF-LOCKING SUPPORT
These cups also represent a true mobile clamping system. They differ from the above cups
for their exceptional height. They are composed of:
- A sturdy, tall aluminium support with a wide surface at the base limited by a seal whose
purpose is to fix it to the bearing surface.

3D drawings are available on vuototecnica.net

- A standard circular flat cup which is cold fitted onto the upper part of the support for
gripping the load.
- A ball valve that opens up creating vacuum, only when activated by the load to be gripped.
- Two quick couplings for vacuum connection.
The gripping plane of these cups is covered with a special non-slip plastic coating, which is
particularly suited for clamping glass and smooth marble.
The detection of vacuum for gripping and releasing the support from the bearing surface
and gripping and releasing the load can be made via three-way vacuum valves or solenoid
valves.
All cups with self-locking support of this and other ranges with the gripping plane at
the same height can be used simultaneously, even if they are of different types or have
different sizes.
Note: Available with support for mechanical fixing with code 28, instead of 18.

SPARE VACUUM CUPS

Force Volume A B C D E F H N Weight
Item
Kg cm3 Ø Ø Ø Ø Ø g
01 110 10 M * 23.74 24.9 96 91 87 114 3 8 17 80 40.1
01 150 10 M * 45.00 75.7 133 125 118 154 4 11 23 117 98.3
01 250 20 * 122.60 200.0 235 227 220 254 4 11 23 220 188.6
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond

Vacuum
Non-slip plastic coating cup
Gripping surface

For Ø 8 ext. hose

O-ring

ROUND VACUUM CUPS WITH BALL VALVE AND HIGH SELF-LOCKING SUPPORT
Force A B C D E F I L M Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
18 110 10/160 MT * 24.0 88 125 51 114 17 30 1 155.5 12 01 110 10 M 00 16 07 2.986
18 150 10/160 MT * 45.0 120 165 68 154 23 30 1 155.5 12 01 150 10 M 00 16 08 5.042
18 250 20/160 MT * 122.6 223 270 121 254 23 33 1 155.5 15 01 250 20 00 18 09 12.634
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.149
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND
HIGH SELF-LOCKING SUPPORT
These cups also represent a true mobile clamping system. They differ from the above
cups for their exceptional height.
They are composed of:
- A sturdy, tall aluminium support with a wide surface at the base limited by a seal whose
3D drawings are available on vuototecnica.net

purpose is to fix it to the bearing surface.

- A standard rectangular flat cup which is cold fitted onto the upper part of the support
for gripping the load.
- A ball valve that opens up creating vacuum, only when activated by the load to be
gripped.
- Two quick couplings for vacuum connection.
The gripping plane of these cups is covered with a special non-slip plastic coating, which
is particularly suited for clamping glass and smooth marble.
The detection of vacuum for gripping and releasing the support from the bearing surface
and gripping and releasing the load can be made via three-way vacuum valves or
solenoid valves.
All cups with self-locking support of this and other ranges with the gripping plane at
the same height can be used simultaneously, even if they are of different types or have
different sizes.
1 Note: Available with support for mechanical fixing with code 28, instead of 18.

SPARE VACUUM CUPS

Force Volume A B E F G H L M N O P Q Weight
Item
Kg cm3 g
01 120 90 * 24.0 42.9 107 78 3 7.5 7.5 17.5 117 87 102 73 97 68 38.8
01 150 75 * 25.0 43.5 137 62 3 7.5 7.5 16.5 147 72 132 57 127 52 41.2
01 300 80 * 60.0 117.6 288 68 3 7.5 7.5 17.5 297 77 284 64 278 58 80.0
01 300 150 * 113.0 268.5 288 138 3 7.5 7.5 17.5 297 147 284 134 278 128 90.0
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond

Non-slip plastic Vacuum

coating cup
Gripping surface

For Ø 8 ext. hose

O-ring

ROUND VACUUM CUPS WITH BALL VALVE AND HIGH SELF-LOCKING SUPPORT
Force A B C D E F G H M N O P Vacuum cup O-ring Weight
Item
Kg item item Kg
18 120 90/160 MT * 24.0 90 120 98 128 17.5 102 12 30 49 51.0 35.0 35.0 01 120 90 00 16 10 3.450
18 150 75/160 MT * 25.0 75 150 83 144 16.5 130 12 30 57 43.5 27.5 27.5 01 150 75 00 16 10 3.262
18 300 80/160 MT * 60.0 80 300 90 310 17.5 284 15 33 140 47.0 31.0 31.0 01 300 80 00 18 10 7.906
18 300 150/160 MT * 113.0 150 300 160 310 17.5 284 15 33 140 83.0 67.0 67.0 01 300 150 00 18 11 13.110
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone; BA= stain-resistant Biond
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.150
ROUND VACUUM CUPS WITH BALL VALVE
AND HIGH SELF-LOCKING SUPPORT, FOR GLASS
Glass machinery manufacturers require increasingly accurate and
safe clamping machines. This has led us to the creation of this series
of cups.
The specially designed shape of this cup guarantees a firm grip.

3D drawings are available on vuototecnica.net

The other main feature is the utmost precision in the height, whose
nominal size has a tolerance of only five hundredths of millimetre.
They are composed of:
- A sturdy aluminium support with a wide surface at the base limited
by a seal whose purpose is to fix it to the bearing surface.
- A standard round flat cup which is cold-assembled onto the upper
part of the support for gripping the load.
- A ball valve that opens up creating vacuum, only when activated by
the load to be gripped.
- Two quick couplings for vacuum connection.
The detection of vacuum, for gripping and releasing the support from
the bearing surface and for gripping and release of glass can be made
via three-way vacuum valves or solenoid valves.

3 seats at 120° for TCCE

M4 screws

SPARE VACUUM CUP

Force Volume A B C D E F H M Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material g
08 65 11 A 6.7 5.5 50 40 20.5 65 10 15 17.5 29.5 steel 90
Compound: A = oil-resistant rubber

Vacuum
cup
Gripping surface

For Ø 8 ext. hose

O-ring

VACUUM CUP WITH BALL VALVE AND SELF-LOCKING SUPPORT

Force A B C D E F G H I L M N Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
18 65 11/90 A 6.7 70 98 45 65 17.5 30 92.5 90 1 75 12 50 08 65 11 A 00 16 06 1.090
Compound: A = oil-resistant rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.151
RECTANGULAR VACUUM CUPS WITH BALL VALVE AND
SELF-LOCKING SUPPORT, FOR GLASS
Glass machinery manufacturers require increasingly accurate and
safe clamping machines. This has led us to the creation of this series
of cups.
The specially designed shape of this cup guarantees a firm grip.
3D drawings are available on vuototecnica.net

The other main feature is the utmost precision in the height, whose
nominal size has a tolerance of only five hundredths of millimetre.
They are composed of:
- A sturdy aluminium support with a wide surface at the base limited
by a seal whose purpose is to fix it to the bearing surface.
- A standard rectangular flat cup which is cold-assembled onto the
upper part of the support for gripping the load.
- A ball valve that opens up creating vacuum, only when activated by
the load to be gripped.
- Two quick couplings for vacuum connection.
The detection of vacuum, for gripping and releasing the support from
the bearing surface and for gripping and release of glass can be made
via three-way vacuum valves or solenoid valves.

2 seats for TCCE

M4 screws

SPARE VACUUM CUP

Force Volume A B D E F H L M N P Q Support Weight
Item
Kg cm3 Ø material g
08 50 75 A 7.5 6.1 60 35 20.5 10 15 17.5 75 50 39.5 50 25 steel 92
Compound: A = oil-resistant rubber

Vacuum
cup
Gripping surface

For Ø 8 ext. hose

O-ring

VACUUM CUP WITH BALL VALVE AND SELF-LOCKING SUPPORT

Force A B C D E G I L P Q Vacuum cup O-ring Weight
Item
Kg item item Kg
18 50 75/90 A 7.5 50 75 65 95 1 92.5 41 75 21 17.5 08 50 75 A 00 16 06 0.762
Compound: A = oil-resistant rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.152
ROUND VACUUM CUPS WITH BALL VALVE,
SELF-LOCKING SUPPORT AND RELEASE BUTTON, FOR GLASS
Glass machinery manufacturers require increasingly accurate and
safe clamping machines. This has led us to the creation of this series
of cups.
The specially designed shape of this cup guarantees a firm grip.

3D drawings are available on vuototecnica.net

The other main feature is the utmost precision in the height, whose
nominal size has a tolerance of only five hundredths of millimetre.
They are composed of:
- A sturdy anodised aluminium support with a wide surface at the
base limited by a seal whose purpose is to fix it to the bearing
surface.
- A standard round flat cup which is cold-assembled onto the upper
part of the support for gripping the load.
- A ball valve that opens up creating vacuum, only when activated by
the load to be gripped.
- A release button that allows placing the support even with the
vacuum inserted.
- Two quick couplings for vacuum connection.
The detection of vacuum, for gripping and releasing the support from
the bearing surface and for gripping and release of glass can be made 1
via three-way vacuum valves or solenoid valves.

3 seats at 120° for TCCE

M4 screws

SPARE VACUUM CUP

Force Volume A B C D E F H M Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material g
08 85 11 A 12 7.7 70 60 40.5 85 10 15 17.5 49.5 steel 92
Compound: A = oil-resistant rubber

Vacuum
cup
Gripping surface

For Ø 8 ext. hose

O-ring
Release button

VACUUM CUPS WITH BALL VALVE, SELF-LOCKING SUPPORT AND RELEASE BUTTON
Force A B C D G I L Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
21 85 11/90 A 12.0 70 98 42 85 92.5 1 75 08 85 11 A 00 16 06 1.090
Compound: A = oil-resistant rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.153
ROUND VACUUM CUPS WITH BALL VALVE,
SELF-LOCKING SUPPORT AND RELEASE BUTTON, FOR GLASS
3D drawings are available on vuototecnica.net

4 seats at 90° for TCCE M6 screws

SPARE VACUUM CUP

Force Volume A B C D E F H M Support Weight
Item
Kg cm3 Ø Ø Ø Ø Ø material Kg
08 150 11 A 42.7 47.1 139 130 41.0 150 10 15 17.5 115.0 steel 1.0
Compound: A = oil-resistant rubber

Vacuum
cup
Gripping surface

For Ø 8 ext. hose

O-ring
Release button

VACUUM CUPS WITH BALL VALVE, SELF-LOCKING SUPPORT AND RELEASE BUTTON
Force A B C D G I L M Vacuum cup O-ring Weight
Item
Kg Ø Ø Ø item item Kg
21 150 11/90 A 42.7 129 165 73 150 92.5 1 75 15 08 150 11 A 00 16 08 3.938
Compound: A = oil-resistant rubber
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.154
ROUND VACUUM CUPS WITH BALL VALVE,
SELF-LOCKING SUPPORT AND RELEASE BUTTON
These cups represent a true mobile clamping system.
They are composed of:
- A sturdy anodised aluminium support with a wide surface at the base limited
by a seal whose purpose is to fix it to the bearing surface.

3D drawings are available on vuototecnica.net

Vacuum
cup
Gripping surface

For Ø 6 int. hose

Release O-ring
button

VACUUM CUPS WITH BALL VALVE, SELF-LOCKING SUPPORT AND RELEASE BUTTON
Force A B C D F G H L M N O P Q T Vacuum cup O-ring Weight
Item
Kg item item Kg
21 120 90 * 24 90 120 56 102 17.5 57.0 54.5 50 98 128 70 24 25 49 01 120 90 00 16 10 1.320
21 150 75 * 25 75 120 48 130 16.5 57.0 54.5 50 83 144 55 25 32 57 01 150 75 00 16 10 1.236
21 150 75/84 * 25 75 150 48 130 16.5 86.5 84.0 80 83 144 55 25 32 57 01 150 75 00 16 10 1.924
* Complete the code indicating the compound: A= oil-resistant rubber; N= natural para rubber; S= silicone
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.157
VACUUM CUPS BASED ON BERNOULLI’S THEOREM

Bernoulli’s theorem explains many phenomena, such as the lifting of

a plane’s wing or of a light disc in front of a tube end from which air
flows out quickly.
This apparently paradoxical phenomenon is exploited for
3D drawings are available on vuototecnica.net

manufacturing vacuum gripping systems (vacuum cups) and

handling, with no contact, fragile objects, such as semiconductor
plates, silica discs, solar cells, precious metal foils, films and whatever
needs to be handled with the greatest care.
Our cups based on Bernoulli’s principle are made with anodised
aluminium, with stainless steel centre thrust disc.
The antistatic silicone spacers, located on the cup gripping plane,
prevent transverse movements of the gripped object.
The compressed air supply connections can be axial and radial and
the quick coupler for the flexible pipe is included in the package.
The unused holes are closed with brass threaded caps.
On the rear part of the cup there are 3 or 4 threaded holes for fitting it
to the automation.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.158
VACUUM CUPS BASED ON BERNOULLI’S THEOREM

3D drawings are available on vuototecnica.net

For Ø 4 mm ext. hose

Connection to additional supply

Max Transverse Operating Consumption Level Weight Fitting Spare rubber pad
Item force force pressure of air of noise included spacer
g g bar Nl/s dB(A) g item item
BEC 20 220 145 5 2.3 66 21 00 BEC 13 00 BEC 10
Note: BEC vacuum cups must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.
For Ø 4 mm ext. hose

Connection to additional supply

Max Transverse Operating Consumption Level Weight Fitting Spare rubber pad
Item force force pressure of air of noise included spacer
g g bar Nl/s dB(A) g item item
BEC 30 380 250 5 2.5 72 31 00 BEC 13 00 BEC 10
Note: BEC vacuum cups must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.159
VACUUM CUPS BASED ON BERNOULLI’S THEOREM
3D drawings are available on vuototecnica.net

For Ø 6 mm ext. hose

1
Connection to additional supply

Max Transverse Operating Consumption Level Weight Fitting Spare rubber pad
Item force force pressure of air of noise included spacer
g g bar Nl/s dB(A) g item item
BEC 40 680 450 5 3.0 74 51 00 BEC 14 00 BEC 09
Note: BEC vacuum cups must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

For Ø 6 mm ext. hose

Connection to additional supply

Max Transverse Operating Consumption Level Weight Fitting Spare rubber pad
Item force force pressure of air of noise included spacer
g g bar Nl/s dB(A) g item item
BEC 60 900 600 5 4.4 75 121 00 BEC 14 00 BEC 09
Note: BEC vacuum cups must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
1.160
VACUUM CUP QUESTIONNAIRE Company

For a correct dimensioning of a vacuum cup handler, it is Address

important to know and assess the features of the load to be
handled.
For this reason, please fill in the following form and send it back Post code / City Country

3D drawings are available on vuototecnica.net

to us via e-mail or fax.
This way, we will be able to suggest you the best cups to solve
your problem. Contact person:
A drawing of the product to be handled or the product itself
would allow us to offer the best solution.
E-mail: [email protected] Telephone Fax
Fax: +39 039 5320015

E-mail

1) In what industry sector are the vacuum cups utilised?

Plastic Packaging Woodworking Cosmetics

1
CD/DVD Glass/Solar Marble/Stone Automotive
Electronics Graphic arts Medical/Pharmaceutical Ceramics/Porcelain
Food Bottling Other sectors

2) With what material is the product to be handled made?

Plastic Glass Wood Paper/Cardboard

Steel sheet Marble/Granite Rubber Other

3) What is the surface of the product to be gripped like?

Dry Moist Smooth Rough Creased

Corrugated Flaky Porous Textured Bush-hammered

4) On the gripping surface there may be substances such as:

Powder Water Oil Solvents Other

5) What shape is the product to be handled?

Square Rectangular Triangular Round

Irregular Other

6) What dimensions and weight is it?

Length mm Width mm Thickness mm Weight Kg

7) Which position must the vacuum cups have with respect to the lifting force?

Horizontal vacuum cups, vertical force Horizontal vacuum cups, horizontal force
%

1.161
VACUUM CUP QUESTIONNAIRE

Vertical vacuum cups, vertical force Overturning

3D drawings are available on vuototecnica.net

1
8) What is the temperature of the object to be lifted?

From - °C to + °C For a short time °C Continuously °C

9) Other technical data

Gripping time sec Cycle time sec Acceleration m/s2

10) At which height above sea level is the vacuum cup handler to be installed?

11) By what means would you like to generate the vacuum?

Electric vacuum pump (dry or lubricated) Side channel blower

Single-stage pneumatic vacuum generator Multi-stage

12) System with vacuum cups already operating

Manufacturer Country

13) Models of vacuum cups previously applied

Manufacturer Code

14) Estimated annual quantity and requested delivery time

Approximately # pieces Fixed period

15) Gripping tests and samples

We can perform free tests for gripping and handling on samples of products supplied by you. Alternatively, you can request samples of
vacuum cups to perform your own tests.

16) Contact

Do you wish to be called back? Yes No

Are you interested in a visit? Yes No If yes, what date/time?
%

1.162
VACUUM CUP HOLDERS

MICRO VACUUM CUP HOLDERS PG. 2.01

MINI VACUUM CUP HOLDERS PG. 2.02 ÷ 2.08

3D drawings are available on vuototecnica.net

MINI VACUUM CUP HOLDERS FOR BELLOWS CUPS PG. 2.09 ÷ 2.16
MINI VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS PG. 2.17 ÷ 2.18
MINI VACUUM CUP HOLDERS WITH BUILT-IN SPRING PG. 2.18
MINI VACUUM CUP HOLDERS WITH COMPACT STROKE PG. 2.19 ÷ 2.21
MINI VACUUM CUP HOLDERS WITH BUILT-IN BUSH PG. 2.22 ÷ 2.23
MINI VACUUM CUP HOLDERS WITH BUILT-IN BUSH, WITH MALE AND FEMALE THREADED CONNECTORS PG. 2.24
MINI VACUUM CUP HOLDERS WITH PLUNGER VALVE PG. 2.25 ÷ 2.29
MINI VACUUM CUP HOLDERS WITH PLUNGER VALVE AND BUILT-IN BUSH PG. 2.30 ÷ 2.34
MINI VACUUM CUP HOLDERS WITH NO SPRINGING PG. 2.35 ÷ 2.39
MINI VACUUM CUP HOLDERS WITH BUILT-IN SHUT-OFF VALVE PG. 2.40
MINI ANTI-ROTATION VACUUM CUP HOLDERS PG. 2.41 ÷ 2.43
MINI VACUUM CUP HOLDERS WITH MAGNETIC SENSOR PG. 2.44
MINI VACUUM CUP HOLDERS FIX PG. 2.45
BASIC VACUUM CUP HOLDERS PG. 2.46 ÷ 2.62
BASIC VACUUM CUP HOLDERS FOR BELLOWS VACUUM CUPS PG. 2.63 ÷ 2.77
BASIC VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS PG. 2.78 ÷ 2.81
BASIC VACUUM CUP HOLDERS WITH PLUNGER VALVE PG. 2.82 ÷ 2.88
BASIC VACUUM CUP HOLDERS WITH NO SPRINGING PG. 2.89 ÷ 2.96
BASIC VACUUM CUP HOLDERS WITH BUILT-IN SHUT-OFF VALVE PG. 2.97 2
BASIC ARTICULATED VACUUM CUP HOLDERS PG. 2.98 ÷ 2.101
BASIC ANTI-ROTATION VACUUM CUP HOLDERS PG. 2.102
BASIC VACUUM CUP HOLDERS FIX PG. 2.103
SPECIAL VACUUM CUP HOLDERS PG. 2.104 ÷ 2.117
SPECIAL VACUUM CUP HOLDERS FOR BELLOWS VACUUM CUPS PG. 2.118 ÷ 2.122
SPECIAL VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS PG. 2.123 ÷ 2.124
SPECIAL VACUUM CUP HOLDERS WITH PLUNGER VALVE PG. 2.125 ÷ 2.129
SPECIAL VACUUM CUP HOLDERS WITH PUSH VALVE PG. 2.130 ÷ 2.131
SPECIAL VACUUM CUP HOLDERS WITH BUILT-IN SHUT-OFF VALVE PG. 2.132
SPECIAL ARTICULATED VACUUM CUP HOLDERS PG. 2.133 ÷ 2.139
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITHOUT GS ARTICULATED JOINT PG. 2.140 ÷ 2.141
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH COMPACT STROKE PG. 2.142 ÷ 2.144
SPECIAL STAINLESS STEEL ANTI-ROTATION VACUUM CUP HOLDERS PG. 2.145
SPECIAL ANTI-ROTATION VACUUM CUP HOLDERS WITH MALE THREADED CONNECTOR PG. 2.146
SPECIAL ANTI-ROTATION VACUUM CUP HOLDERS WITH SPHERICAL SWIVEL SUPPORT PG. 2.147 ÷ 2.148
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING PG. 2.149 ÷ 2.157
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING PG. 2.158 ÷ 2.164
SPHERICAL ARTICULATED JOINTS PG. 2.165
SPHERICAL ARTICULATED JOINTS WITH AXIAL VACUUM CONNECTION PG. 2.166
POSITIONABLE SPHERICAL ARTICULATED JOINTS WITH AXIAL VACUUM CONNECTION PG. 2.167
VACUUM CUP HOLDER FIXING SUPPORTS PG. 2.168 ÷ 2.170
2
3D drawings are available on vuototecnica.net
MICRO VACUUM CUP HOLDERS

- Extremely reduced size and weight

- Stainless steel stems and spring
- Self-lubricating bush built in the threaded sleeve ensuring a
perfect sliding of the stem and durability

3D drawings are available on vuototecnica.net

- Indicated for Pick & Place units and handling machines for
unloading plastic objects from a mould press
- Available in various versions with or without coupling
- Suitable for all vacuum cups with male M5 support

VERSION 20 80 05 L

For Ø 4 int. hose

Stroke 10

Sp13 Sp10

Sp13 Sp13

VERSION 20 80 05

VERSION 20 80 05 T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
d E F L Weight
Item
Ø Ø g
20 80 05 M5 10 M10 x 0.75 73.5 20
Note: To order vacuum cup holders with L or T fittings, add the letter L or T to the code.
For Ø 3 ext. hose

Stroke 10 Stroke 10

Sp13 Sp13

Sp13 Sp13 Sp13 Sp7

VERSION 20 80 05 SR VERSION 20 80 05 RR

d E F L Weight
Item
Ø Ø g
20 80 05 SR M5 10 M10 x 0.75 56 14
20 80 05 RR M5 10 M10 x 0.75 63 16

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.01
MINI VACUUM CUP HOLDERS

The main feature of the cup holders described on these pages

is their reduced size, which results in a reduced weight and
bulk. They allow use of even very small cups, guaranteeing,
given the same diameter, the same performance as the larger
3D drawings are available on vuototecnica.net

series.
They are composed of:
- A brass stem for fastening the cup
- A threaded sleeve equipped with nuts, for mounting the
vacuum up holder on the automation
- A spring to cushion the impact of the cup and to, at the same
time, keep pressure with the load to be lifted
- A quick coupling for connection with the suction hose

Vacuum
cup
2

Vacuum
cup
2

Screw

VERSION 20 . . 30 L
For Ø 4 int. hose

Vacuum
cup Stroke 25.5 Sp19 Sp10

Sp17
Screw
VERSION 20 . . 30

VERSION 20 . . 30 T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
Force D E F L For vacuum cup Screw included Weight
Item
Kg Ø Ø item item g
20 25 30 1.23 25.0 8 M12 x 1.25 96 01 25 10 00 20 12 75.2
20 30 30 1.76 30.0 8 M12 x 1.25 96 01 30 10 00 20 12 75.9
20 35 30 2.40 35.0 8 M12 x 1.25 96 01 35 10 00 20 12 76.4
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L or T fittings, add the letter L or T to the code.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.05
MINI VACUUM CUP HOLDERS
3D drawings are available on vuototecnica.net

2
Vacuum
cup

VERSION 20 . . 24 L
For Ø 4 int. hose

Vacuum Stroke 25.5 Sp19 Sp10

cup

Sp17

VERSION 20 . . 24

VERSION 20 . . 24 T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
Force D E F L For vacuum cup Weight
Item
Kg Ø Ø item g
20 27 24 1.43 27.0 24 M12 x 1.25 112 01 27 24 76.8
20 30 24 1.76 30.0 24 M12 x 1.25 112 01 30 24 76.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L or T fittings, add the letter L or T to the code.

3D drawings are available on vuototecnica.net

Vacuum 2
cup

Screw

VERSION 20 . . 30 L
For Ø 4 int. hose

Vacuum
cup
Stroke 25.5 Sp19 Sp10

Sp17

Screw
VERSION 20 . . 30

VERSION 20 . . 30 T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
Force D E F L For vacuum cup Screw included Weight
Item
Kg Ø Ø item item g
20 45 30 3.98 45 18 M12 x 1.25 106 01 45 10 00 20 13 80.7
20 60 30 7.06 60 22 M12 x 1.25 110 01 60 10 00 20 13 88.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L or T fittings, add the letter L or T to the code.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.07
MINI VACUUM CUP HOLDERS
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Screw

VERSION 20 . . . . L
For Ø 4 int. hose

cup

Support Sp17

VERSION 20 . . . .

VERSION 20 . . . . T

The cup holders described on these pages share the same

features as the previously described ones, but differ for their
brass stem, which has 1/8” and ¼” gas threaded female
connection, for the exclusive installation of cups with male

3D drawings are available on vuototecnica.net

threaded support and for the vacuum connection, which can
either be radial or axial, upon request.

For Ø 4 int. hose

Stroke 25.5 Sp19 Sp10 VERSION 20 . . . . L

Sp17

VERSION 20 . . . . VERSION 20 . . .. T 2

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
d D E F L Weight
Item
Ø Ø Ø g
20 06 35 M5 7.0 3.5 M12 x 1.25 91.5 74
20 07 35 M8 12.0 9 M12 x 1.25 97 76
20 10 38 G1/8” 14.0 9 M12 x 1.25 97 78
20 10 48 G1/4” 16.5 9 M12 x 1.25 97 78
Note: To order vacuum cup holders with L or T fittings, add the letter L or T to the code.
For Ø 4 int. hose

Stroke 25.5 Sp19 Sp10

VERSION 20 10 . . M L

Sp17

VERSION 20 10 . . M

VERSION 20 10 . . M T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
D E F L Weight
Item
Ø Ø g
20 10 38 M G1/8” 8 M12 x 1.25 96 78
20 10 48 M G1/4” 10 M12 x 1.25 98 76
20 10 58 M G3/8” 10 M12 x 1.25 98 76
Note: To order vacuum cup holders with L or T fittings, add the letter L or T to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.17
MINI VACUUM CUP HOLDERS WITH FEMALE THREADED CONNECTORS

Sp19
Stroke 25.5
3D drawings are available on vuototecnica.net

VERSION 20 80 25

Sp10
For Ø 4 int. hose

VERSION 20 80 25 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
d D E F L Weight
Item
Ø Ø Ø g
2 20 80 25 G1/8” 15 15 M12 x 1.25 83.5
. 82
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

MINI VACUUM CUP HOLDERS WITH BUILT-IN SPRING

For a further bulk and weight reduction, as well as to meet the requirements of discharge automations for
plastic moulding press manufacturers, these cup holders are made with a built-in spring and an anodised
aluminium cup fixing stem. Also these cup holders allow for the installation of cups with male threaded
support only. The particular shape of the brass drive bush for fastening the cup holder to the automation
prevents any rotation of the stem and, therefore, of the cup.
The vacuum connection is radial.

VERSION 20 80 . .
Sp10

For Ø 4 int. hose

VERSION 20 80 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
B C d D F L Weight
Item
stroke Ø Ø Ø g
20 80 15 22 15 G1/8” 15 M10 x 0.75 72 26
20 80 20 32 20 G1/8” 15 M15 x 1.00 87 42
Note: To order chrome-plated iron, add the letters FC to the item.
To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.18
MINI VACUUM CUP HOLDERS WITH COMPACT STROKE

The shorter stroke and their particular shape allow for further
bulk and weight reduction of these cup holders, with respect to
the previous mini vacuum cup holders.
The components are practically the same, only the vacuum

3D drawings are available on vuototecnica.net

fittings are different, since in these cup holders they are a radial
standard hose-end fitting or two fittings, upon request.
They are particularly suited for small cups to be manually
assembled with diameters ranging between 10 and 30 mm.

VERSION 20 07 13

Cap 00 20 69
2
Vacuum
cup

Fitting 00 20 61

Sp17 Sp19

Vacuum
cup

VERSION 20 . . 13 DR

VACUUM CUP HOLDERS WITH STRAIGHT COUPLER FOR PLASTIC HOSE

Force B C E F L For vacuum cup Weight
Item
Kg stroke Ø item g
20 07 13 0.09 12.4 15 23 M12 x 1.25 53 01 07 13 56.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cups with 2 fittings item 00 20 61 fittings, add the letters DR to code.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.19
MINI VACUUM CUP HOLDERS WITH COMPACT STROKE
3D drawings are available on vuototecnica.net

VERSION 20 . . 10

Vacuum Cap 00 20 69
cup
2

Fitting 00 20 61

Vacuum Sp17 Sp19

cup

VERSION 20 . . 10 DR

VACUUM CUP HOLDERS WITH STRAIGHT COUPLER FOR PLASTIC HOSE

Force B D E F L For vacuum cup Weight
Item
Kg stroke Ø Ø item g
20 10 10 0.19 12.4 10 21 M12 x 1.25 51 01 10 10 56.0
20 12 10 0.28 12.4 12 21 M12 x 1.25 51 01 12 10 56.6
20 15 10 0.44 12.4 15 22 M12 x 1.25 52 01 15 10 56.7
20 18 10 0.63 12.4 18 22 M12 x 1.25 52 01 18 10 56.7
20 20 10 0.78 12.4 20 22 M12 x 1.25 52 01 20 10 56.8
20 22 10 0.95 12.4 22 23 M12 x 1.25 53 01 22 10 57.2
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cups with 2 fittings item 00 20 61 fittings, add the letters DR to code.

3D drawings are available on vuototecnica.net

VERSION 20 . . 10

Cap 00 20 69
2
Vacuum
cup

Fitting 00 20 61

Vacuum Sp17 Sp19

cup

VERSION 20 . . 10 DR

VACUUM CUP HOLDERS WITH STRAIGHT COUPLER FOR PLASTIC HOSE

Force B D E F L For vacuum cup Weight
Item
Kg stroke Ø Ø item g
20 25 10 1.23 12.4 25 26 M12 x 1.25 56 01 25 15 58.0
20 30 10 1.76 12.4 30 26 M12 x 1.25 56 01 30 15 58.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cups with 2 fittings item 00 20 61 fittings, add the letters DR to code.

The reduced size and the particular shape of these cup holders
allow them to be directly assembled to the vacuum manifold,
saving time and eliminating pipes and fittings.
The hexagonal threaded bush for cup holder assembly with the
3D drawings are available on vuototecnica.net

vacuum manifold is equipped with a seal and has the task of

driving and holding the brass stem for fixing the vacuum cup.

2
VERSION 20 . . 11

Vacuum
cup

Vacuum Sp17 Sp20

cup

Stroke 16.4

Force D E F L For vacuum cup Weight

Item
Kg Ø Ø item g
20 25 11 1.23 25 21 G3/8” 74 01 25 15 70.0
20 30 11 1.76 30 22 G3/8” 75 01 30 15 70.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

3D drawings are available on vuototecnica.net

2
VERSION 20 . . 11

Vacuum
cup

Sp17 Sp20

Stroke 16.4

Force D E F L For vacuum cup Weight

Item
Kg Ø Ø item g
20 35 11 2.40 35 21 G3/8” 74 01 35 15 76.6
20 40 11 3.14 40 23 G3/8” 76 01 40 15 77.1
20 45 11 3.98 45 28 G3/8” 81 01 45 15 80.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.23
VACUUM CUP HOLDERS WITH BUILT-IN BUSH,
WITH FEMALE THREADED CONNECTOR
3D drawings are available on vuototecnica.net

VERSION 20 . . 11

Sp17 Sp20

Stroke 16.4
2

d D E F L Weight
Item
Ø Ø Ø g
20 08 11 G1/8” 14.0 9 G3/8” 67 74
20 10 11 G1/4” 16.5 9 G3/8” 67 73

VACUUM CUP HOLDERS WITH BUILT-IN BUSH,

WITH MALE THREADED CONNECTOR

VERSION 20 . . 11 M

Sp17 Sp20

Stroke 16.4

d E F L Weight
Item
Ø Ø g
20 08 11 M G1/8” 8 G3/8” 66 75
20 10 11 M G1/4” 10 G3/8” 68 74

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1,130
25.4 453.6 0.4536
2.24
MINI VACUUM CUP HOLDERS WITH PLUNGER VALVE

They share the same mechanical features at the other mini

vacuum cup holders.
Their distinctive feature is the plunger valve solidly connected
to a conical spear valve, which activates suction, and therefore

3D drawings are available on vuototecnica.net

creates vacuum, only when the cup comes into contact with
the load to be lifted.

Vacuum 2
cup

VERSION 20 . . 60 L
For Ø 4 int. hose

Sp12 Stroke 25.5 Sp19 Sp10

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.30
MINI VACUUM CUP HOLDERS WITH PLUNGER VALVE AND BUILT-IN BUSH

3D drawings are available on vuototecnica.net

VERSION 20 . . 65

Vacuum
cup

Vacuum Sp12 Sp20

cup

Stroke 16.4

Force B C D E F L M For vacuum cup Weight

Item
Kg Ø Ø item g
20 20 65 0.78 5.5 8.5 20 12 G3/8” 89 2 01 20 10 76.8
20 22 65 0.95 5.5 8.5 22 13 G3/8” 90 1 01 22 10 77.2
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.31
MINI VACUUM CUP HOLDERS WITH PLUNGER VALVE AND BUILT-IN BUSH
3D drawings are available on vuototecnica.net

2
VERSION 20 25 65

Sp12 Sp20

Stroke 16.4

Vacuum
cup

Force B C D E F L M For vacuum cup Weight

Item
Kg Ø Ø item g
20 35 65 2.40 7 11 35 16 G3/8” 93 2 01 35 15 82.6
20 40 65 3.14 7 11 40 18 G3/8” 95 0 01 40 15 83.1
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.34
MINI VACUUM CUP HOLDERS WITH PLUNGER VALVE WITH NO SPRINGING

They have the same function as the mini vacuum cup

holders with plunger valve but, for further bulk reduction, the
cushioning spring, the threaded pipe with nuts for fixing to the
automation and the quick coupler have been removed.

3D drawings are available on vuototecnica.net

This type of cup holder is to be directly assembled to the
vacuum manifold.
To allow quick assembly, its end is provided with a threaded
male shank.

VERSION 20 . . 61

Vacuum
cup

Vacuum Sp12
cup

Force B C D E F L M For vacuum cup Weight

Item
Kg Ø Ø item g
20 12 61 0.28 4.5 8.5 12 11 G1/8” 43 2 01 12 10 24.6
20 15 61 0.44 4.5 8.5 15 12 G1/8” 44 1 01 15 10 24.7
20 18 61 0.63 4.5 8.5 18 12 G1/8” 44 1 01 18 10 24.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.35
MINI VACUUM CUP HOLDERS WITH NO SPRINGING
3D drawings are available on vuototecnica.net

Item Kg Ø Ø item g

20 30 61 1.76 7 11 30 17 G1/8” 49 01 30 15 28.6

Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

3D drawings are available on vuototecnica.net

VERSION 20 . . 61

Vacuum
cup

Sp12

Vacuum
cup

Force B C D E F L M For vacuum cup Weight

Item
Kg Ø Ø item g
20 35 61 2.40 7 11 35 16 G1/8” 48 2 01 35 15 34.6
20 40 61 3.14 7 11 40 18 G1/8” 50 0 01 40 15 35.1
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.39
MINI VACUUM CUP HOLDERS WITH BUILT-IN SHUT-OFF VALVE

In addition to having all the other features of the mini vacuum

cup holders, these also have a built-in shut-off valve.
The function of the shut-off valve is to automatically close
suction when the cup is not in contact with the surface of the
3D drawings are available on vuototecnica.net

load to be handled or in case of a faulty grip or of considerable

transpiration, thus preventing the reduction of the level of
vacuum on the remaining cups of the system that are regularly
gripping a load.
The advantage of this is that the placement or the exclusion of
the non-gripping cups is no longer binding.
Vacuum cups with a minimum diameter of 10 mm and
maximum diameter of 50 mm can be assembled on these cup
holders, provided they have a 1/8 "male threaded gas support.

VERSION 20 99 35 L
For Ø 4 int. hose

Stroke 25.5 Sp19 Sp10

Sp13

VERSION 20 99 35

VERSION 20 99 35 T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
A C D E F L Weight
Item
Ø Ø g
20 99 35 17.5 35.5 G1/8” 24 M12 x 1.25 107 84
Minimum trigger flow = 1.5 m3/h Minimum a level of vacuum = -250 mbar
Note: To order vacuum cup holders with L or T fittings, add the letter L or T to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.40
MINI ANTI-ROTATION VACUUM CUP HOLDERS

The technical features are the same as for the mini vacuum
cup holders, with their distinctive features being their brass
stem with hexagonal section and the steel drive bush with
hexagonal hole. This prevents the stem from rotating on

3D drawings are available on vuototecnica.net

its axis, and, as a result, also the cup and its support from
rotating.
They are suited for cups with male or female support with
diameters ranging from 10 mm to 60 mm, but they have been
specially designed for the installation of rectangular, concave
and elliptical cups.

VERSION 20 95 08 L
For Ø 4 int. hose

This is the reason why they are recommended to be used
on piece counter handlers, boxing machines and in all those
cases in which the presence of the gripped object is to be
guaranteed. These cup holders have been designed for
gripping chocolate, snacks, croissants and similar products
and they are currently made in the version represented on this
page. They can however be made with different vacuum cups
upon request.

Vacuum
cup

Magnetic sensor

VERSION 20 99 02 L
For Ø 4 int. hose

Sp17 Stroke 25.5 Sp19 Sp10

Vacuum
cup

Magnetic sensor

VERSION 20 99 02

Vacuum
cup VERSION 20 99 02 T

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
Force A D F G H I M For vacuum cup Weight
Item
Kg Ø Ø item g
20 99 02 0.70 17 19 M12 x 1.25 18 20 10 28 01 19 17 163.3
1.23 16 25 M12 x 1.25 18 20 10 28 01 25 15 161.3
20 99 03
1.76 17 35 M12 x 1.25 18 20 10 28 01 30 15 162.0
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L or T fittings, add the letter L or T to the code.
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.44
MINI VACUUM CUP HOLDERS FIX

These are simple nickel-plated brass threaded bushes with

screwing nuts for height adjustment and with threaded ends,
one to assemble the vacuum cup with support and the other
for the quick coupling connecting the suction hose.

3D drawings are available on vuototecnica.net

For Ø 4 int. hose

2
Sp8
Sp12

VERSION 20 70 01 VERSION 20 70 01 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
D E F L Weight
Item
Ø Ø g
20 70 01 M5 6 G1/8” 46 19
Note: To order vacuum cup holders with L fittings, add the letter L to the code.
For Ø 4 int. hose

Sp10
Sp19

VERSION 20 70 05 VERSION 20 70 05 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6
D E F L Weight
Item
Ø Ø g
20 70 05 M5 6 M12 x 1.25 46 45
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.45
BASIC VACUUM CUP HOLDERS

These cup holders are built in a simple and rational way,

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 27 24 1.43 28 27 39 M20 139 01 27 24 216.8 228.8 287.8
02 30 24 1.76 28 30 39 M20 139 01 30 24 216.9 228.9 287.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum 2
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 32 36 VERSION 02 32 36 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 32 36 2.00 28 32 51 M20 151 01 32 36 221.1 269.1 289.1
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum
cup For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 . . 15 VERSION 02 . . 15 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 35 15 2.40 28 35 31 M20 131 01 35 15 218.6 266.6 293.6
02 40 15 3.14 28 40 33 M20 133 01 40 15 219.1 267.1 294.1
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

2
Vacuum
cup

Screw
For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Screw Sp20

VERSION 02 . . 10 VERSION 02 . . 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Screw included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 45 10 3.98 28 45 33 M20 133 01 45 10 00 20 13 222.7 270.7 336.7
02 60 10 7.06 28 60 37 M20 137 01 60 10 00 20 13 230.9 278.9 344.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp20

VERSION 02 45 15 VERSION 02 45 15 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 45 15 3.98 28 45 38 M20 138 01 45 15 222.6 272.6 295.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

2
Vacuum
cup

Screw
For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Screw Sp20

VERSION 02 . . . . VERSION 02 . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Screw included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 50 20 4.90 28 50 35 M20 135 01 50 20 00 20 14 226.0 277.0 300.0
02 65 28 8.29 28 65 43 M20 143 01 65 28 00 20 14 231.7 282.7 305.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

2 Vacuum
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

VERSION 02 110 10 VERSION 02 110 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Support included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 110 10 23.74 28 114 32 M20 132 01 110 10 00 08 33 456 494 521
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum Cap
cup

Cap
For Ø 6 int. hose

Sp30 Sp17

Sp20

Vacuum
cup

VERSION 02 110 15 VERSION 02 110 15 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Cap included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 110 15 23.74 28 110 41 M20 141 08 110 15 00 11 06 571 608 636
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum
cup
2

For Ø 6 int. hose

Vacuum Sp30
Sp30 Sp17
cup

Sp20

VERSION 02 20 23 VERSION 02 20 23 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 20 23 0.78 28 20 38 M20 138 01 20 23 213.8 256.8 283.8
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

2
Vacuum
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 . . . . VERSION 02 . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 22 19 0.95 28 22 34 M20 134 01 22 19 214.7 257.7 284.7
02 34 26 2.26 28 34 41 M20 141 01 34 26 217.7 260.7 287.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 25 35 VERSION 02 25 35 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 25 35 1.23 28 25 50 M20 150 01 25 35 219 231 290
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum
2
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp20

VERSION 02 . . . . VERSION 02 . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 30 32 1.76 28 30 47 M20 147 01 30 32 219.6 264.6 294.6
02 40 42 3.14 28 40 57 M20 157 01 40 42 215.6 270.6 300.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum 2
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 30 . . VERSION 02 30 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 30 50 1.76 28 30 53 M20 153 01 30 50 221.6 258.6 285.6
02 30 99 1.76 28 30 53 M20 153 01 30 99 222.2 259.2 286.2
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

2 Vacuum
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 30 55 VERSION 02 30 55 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 30 55 1.76 28 30 70 M20 170 01 30 55 226.8 263.8 290.8
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum 2
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp20

VERSION 02 . . 30 VERSION 02 . . 30 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 40 30 3.14 28 40 67 M20 167 08 40 30 256.4 296.4 325.4
02 50 30 4.90 28 50 69 M20 169 08 50 30 264.9 304.9 333.9
02 60 30 7.06 28 60 71 M20 171 08 60 30 277.6 317.6 346.6
02 85 30 14.18 28 85 82 M20 182 08 85 30 346.0 386.0 415.0
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
2

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp17

VERSION 02 40 50 VERSION 02 40 50 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 40 50 3.14 28 40 38 M20 138 01 40 50 220.6 255.6 282.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum
cup
2

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp20

VERSION 02 . . . . VERSION 02 . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 40 60 3.14 28 40 84 M20 184 08 40 60 265.6 304.6 334.6
02 50 50 4.90 28 50 87 M20 187 08 50 50 275.6 314.6 344.6
02 60 50 7.06 28 60 91 M20 191 08 60 50 248.4 337.4 367.4
02 85 50 14.18 28 85 110 M20 210 08 85 50 394.0 433.0 463.0
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

2 Vacuum
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp20

VERSION 02 43 28 VERSION 02 43 28 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 43 28 3.62 28 43 43 M20 143 01 43 28 225 269 299
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum 2
cup

For Ø 6 int. hose

Sp30 Sp17

Sp20

Vacuum
cup

VERSION 02 50 53 VERSION 02 50 53 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 50 53 4.90 28 50 68 M20 168 01 50 53 247.4 286.4 315.4
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

For Ø 6 int. hose

Vacuum Sp30 Sp17

cup

Sp20

VERSION 02 52 50 VERSION 02 52 50 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 52 50 5.30 28 52 57 M20 157 01 52 50 248.7 298.7 325.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum
cup
For Ø 6 int. hose

Sp30 Sp17

Sp20

Vacuum
cup

VERSION 02 53 35 VERSION 02 53 35 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 53 35 5.51 28 53 41 M20 141 01 53 35 241.6 279.6 308.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

2 Vacuum
cup

For Ø 6 int. hose

Sp30 Sp17

Sp17
Vacuum
cup

VERSION 02 . . 30 VERSION 02 . . 30 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 56 30 6.15 28 56 33 M20 133 01 56 30 236.0 243.0 264.0
02 75 30 11.04 28 75 69 M20 169 01 75 30 255.6 262.6 283.6
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum
cup
2

Support
For Ø 6 int. hose

Support Sp30 Sp17

Sp20

Vacuum
cup

VERSION 02 75 42 VERSION 02 75 42 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Support included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 75 42 11.04 28 75 57 M20 157 01 75 42 00 08 126 317.8 355.8 382.8
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.77
BASIC VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS

These basic vacuum cup holders also have the same characteristics and offer the same
performance as those previously described. Their distinctive feature is the brass stem
with a threaded male or female end for fixing the cup.
The cups to be assembled onto these vacuum cup holders must be equipped with the
3D drawings are available on vuototecnica.net

suited threaded support.

The actual springing stroke is:
- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

Basic vacuum cup holders with female threaded connectors

For Ø 6 int. hose

Sp17 Sp30 Sp17

VERSION 02 08 . . VERSION 02 08 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 08 28 32 40 28 G1/8” 15 M20 115 207
02 08 65 32 40 65 G1/8” 15 M20 152 243
02 08 95 32 40 95 G1/8” 15 M20 182 272
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

Basic vacuum cup holders with male threaded connectors

For Ø 6 int. hose

Sp17 Sp30 Sp17

VERSION 02 08 . . M VERSION 02 08 . . M L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 08 28 M 32 40 28 G1/8” 15 M20 123 216
02 08 65 M 32 40 65 G1/8” 15 M20 160 252
02 08 95 M 32 40 95 G1/8” 15 M20 190 282
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.78
BASIC VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Basic vacuum cup holders with female threaded connectors

For Ø 6 int. hose

Sp20 Sp30 Sp17

VERSION 02 10 . . VERSION 02 10 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 10 28 32 40 28 G1/4” 20 M20 120 224
02 10 65 32 40 65 G1/4” 20 M20 157 262
02 10 95 32 40 95 G1/4” 20 M20 187 289
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

Basic vacuum cup holders with male threaded connectors

For Ø 6 int. hose

Sp20 Sp30 Sp17

VERSION 02 10 . . M VERSION 02 10 . . M L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 10 28 M 32 40 28 G1/4” 15 M20 124 225
02 10 65 M 32 40 65 G1/4” 15 M20 161 266
02 10 95 M 32 40 95 G1/4” 15 M20 191 295
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.79
BASIC VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Basic vacuum cup holders with female threaded connectors

For Ø 6 int. hose

Sp20 Sp30 Sp17

2
VERSION 02 11 . . VERSION 02 11 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 11 28 32 40 28 M12 20 M20 120 226
02 11 65 32 40 65 M12 20 M20 157 264
02 11 95 32 40 95 M12 20 M20 187 291
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

Basic vacuum cup holders with male threaded connectors

For Ø 6 int. hose

Sp20 Sp30 Sp17

VERSION 02 11 . . M VERSION 02 11 . . M L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 11 28 M 32 40 28 M12 15 M20 124 223
02 11 65 M 32 40 65 M12 15 M20 161 264
02 11 95 M 32 40 95 M12 15 M20 191 293
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.80
BASIC VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Basic vacuum cup holders with female threaded connectors

For Ø 6 int. hose

Sp20 Sp30 Sp17

2
VERSION 02 12 . . VERSION 02 12 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 12 28 32 40 28 G3/8” 25 M20 125 220
02 12 65 32 40 65 G3/8” 25 M20 162 259
02 12 95 32 40 95 G3/8” 25 M20 192 285
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

Basic vacuum cup holders with male threaded connectors

For Ø 6 int. hose

Sp20 Sp30 Sp17

VERSION 02 12 . . M VERSION 02 12 . . M L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 12 28 M 32 40 28 G3/8” 15 M20 125 237
02 12 65 M 32 40 65 G3/8” 15 M20 162 274
02 12 95 M 32 40 95 G3/8” 15 M20 192 303
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.81
BASIC VACUUM CUP HOLDERS WITH PLUNGER VALVE

They offer the same mechanical performance at the basic mini

vacuum cup holders. They are characterised by a plunger valve
solidly connected to a conical spear valve, which activates
suction, and therefore creates vacuum, only when the cup
3D drawings are available on vuototecnica.net

comes into contact with the load to be lifted.

The actual springing stroke is:
- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

Screw Vacuum
cup
For Ø 6 int. hose

Vacuum Sp22 Sp22 Sp30 Sp17

cup

Screw

VERSION 03 45 10 VERSION 03 45 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Screw included Weight Weight Weight
Item
Kg Ø Ø item item g g g
03 45 10 3.98 28 45 70 M20 170 01 45 10 00 20 13 344.7 381.7 415.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Disc Screw Vacuum

cup
For Ø 6 int. hose

Vacuum
cup Sp22 Sp22 Sp30 Sp17

Screw

Disc

VERSION 03 60 10 VERSION 03 60 10 L

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Support
Disc

Vacuum
cup
For Ø 6 int. hose

Sp22 Sp22 Sp30 Sp17

Support

Disc

VERSION 03 110 10 VERSION 03 110 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force *C D E F L For vacuum cup Support included Disc included Weight Weight Weight
Item
Kg Ø Ø item item item g g g
03 110 10 23.74 28 114 70 M20 170 01 110 10 00 08 33 00 03 22 618.3 549.3 683.3
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 65 mm and 95 mm

Their function is the same as the previously described basic

vacuum cup holders with plunger valve but, for further bulk
reduction, the cushioning spring, the threaded bush with nuts
for fixing to the automation and the quick coupler have been

3D drawings are available on vuototecnica.net

removed. This type of cup holder must be assembled onto the
vacuum manifold by means of a threaded male shank on its end.

Vacuum
cup

Screw

Vacuum
cup Sp22 Sp22

Screw

VERSION 03 45 11

Force A D E F L For vacuum cup Screw included Weight

Item
Kg Ø Ø item item g
03 45 11 3.98 15 45 70 G1/4” 85 01 45 10 00 20 13 174.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.89
BASIC VACUUM CUP HOLDERS WITH NO SPRINGING
3D drawings are available on vuototecnica.net

Vacuum
cup

Disc Screw

Vacuum
cup
Sp22 Sp22

Screw

Disc

VERSION 03 60 11

Force A D E F L For vacuum cup Screw included Disc included Weight

Item
Kg Ø Ø item item item g
03 60 11 7.06 15 60 72 G1/4” 87 01 60 10 00 20 13 00 03 22 191.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

3D drawings are available on vuototecnica.net

2
Vacuum
cup

Disc
Support

Vacuum
cup
Sp22 Sp22

Support

Disc

VERSION 03 65 16

Force A D E F L For vacuum cup Support included Disc included Weight

Item
Kg Ø Ø item item item g
03 65 16 8.29 15 65 70 G1/4” 85 01 65 15 00 08 32 00 03 22 287.4
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.91
BASIC VACUUM CUP HOLDERS WITH NO SPRINGING
3D drawings are available on vuototecnica.net

2
Vacuum
cup

Support
Disc

Vacuum
cup

Sp22 Sp22

Support

Disc

VERSION 03 80 21

Force A D E F L For vacuum cup Support included Disc included Weight

Item
Kg Ø Ø item item item g
03 80 21 12.56 15 80 73 G1/4” 88 01 80 20 00 08 126 00 03 22 260.2
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

3D drawings are available on vuototecnica.net

Vacuum
cup

Screw

Disc

Vacuum
cup

Sp22 Sp22

Screw

Disc

VERSION 03 85 11

Force A D E F L For vacuum cup Screw included Disc included Weight

Item
Kg Ø Ø item item item g
03 85 11 14.18 15 85 92 G1/4” 107 01 85 10 00 20 13 00 03 22 247.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.93
BASIC VACUUM CUP HOLDERS WITH NO SPRINGING
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Disc Support

Vacuum
cup

Sp22 Sp22

Support

Disc

VERSION 03 85 16

Force A D E F L For vacuum cup Support included Disc included Weight

Item
Kg Ø Ø item item item g
03 85 16 14.18 15 85 70 G1/4” 85 01 85 15 00 08 32 00 03 22 302.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

3D drawings are available on vuototecnica.net

Vacuum
cup

Support
Disc

Vacuum
cup

Sp22 Sp22

Support

Disc

VERSION 03 110 11

Force A D E F L For vacuum cup Support included Disc included Weight

Item
Kg Ø Ø item item item g
03 110 11 23.74 15 114 70 G1/4” 85 01 110 10 00 08 33 00 03 22 441.3
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.95
BASIC VACUUM CUP HOLDERS WITH NO SPRINGING
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Sp20

Vacuum
cup

VERSION 03 . . . .

Force A B D E F L For vacuum cup Weight

Item
Kg Ø Ø item g
03 50 41 4.90 13 18.0 50 46.0 G3/8” 59.0 08 50 40 100.6
03 75 41 11.04 13 27.0 75 55.0 G3/8” 68.0 08 75 40 120.0
03 100 41 19.62 13 28.0 100 56.0 G3/8” 69.0 08 100 40 140.4
03 100 51 19.62 13 32.5 100 60.5 G3/8” 73.5 08 100 50 136.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.96
BASIC VACUUM CUP HOLDERS WITH BUILT-IN SHUT-OFF VALVE

Along with all the other features they share with the other basic
vacuum cup holders, these have a built-in shut-off valve.
The function of the shut-off valve is to automatically close
suction when the cup is not in contact with the surface of the

3D drawings are available on vuototecnica.net

load to be handled or in case of a faulty grip or of considerable
transpiration, thus preventing the reduction of the level of
vacuum on the remaining cups of the system that are regularly
gripping a load.
The advantage of this is that the placement or the exclusion of
the non-gripping cups is no longer binding.
Vacuum cups with a minimum diameter of 35 mm and
maximum diameter of 85 mm can be assembled on these cup
holders, provided they have a¼” male threaded gas support.
The actual springing stroke is:
- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

For Ø 6 int. hose

Sp20 Sp30 Sp17

VERSION 02 99 . . VERSION 02 99 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F L Weight
Item
Ø Ø g
02 99 28 32 40 28 G1/4” 30 M20 130 256
02 99 65 32 40 65 G1/4” 30 M20 167 301
02 99 95 32 40 95 G1/4” 30 M20 197 333
Minimum trigger flow = 4 m3/h Minimum level of vacuum = -250 mbar
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.97
BASIC ARTICULATED VACUUM CUP HOLDERS

The technical and mechanical features are the same as for

the basic vacuum cup holders. Their distinctive feature is
their articulated joint in hardened steel, which allows the flat
cups installed on these cup holders to adapt themselves to
3D drawings are available on vuototecnica.net

the loads to be lifted with slightly tilted surfaces, as well as to

compensate possible verticality errors that can arise between
the cup holder and the automation fixing support.
The actual springing stroke is:
- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

Vacuum Support
cup

Vacuum Support
cup
Sp17 Sp10

Sp30
For Ø 6 int. hose

VERSION 02 65 20

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 65 20 8.29 21 37 28 65 M20 52 130 01 65 16 00 02 36 382.4 431.4 461.4
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 65 mm and 95 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.98
BASIC ARTICULATED VACUUM CUP HOLDERS

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum Support
cup

Vacuum
cup
Support

Sp17 Sp10

Sp30
For Ø 6 int. hose

VERSION 02 85 20

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 85 20 14.18 21 37 28 85 M20 52 130 01 85 16 00 02 36 400.7 449.7 479.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 65 mm and 95 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.99
BASIC ARTICULATED VACUUM CUP HOLDERS

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm
3D drawings are available on vuototecnica.net

Vacuum Support
cup

Vacuum
cup

Support

Sp17 Sp10

Sp30
For Ø 6 int. hose

VERSION 02 110 20

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight Weight
Item
Kg Ø Ø item item g g g
02 110 20 23.74 26 37 28 114 M20 52 130 01 110 10 00 02 37 540.3 587.3 614.3
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 65 mm and 95 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.100
BASIC ARTICULATED VACUUM CUP HOLDERS

The actual springing stroke is:

- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

3D drawings are available on vuototecnica.net

Vacuum
cup 2

Vacuum
cup

Sp17 Sp10

Sp30
For Ø 6 int. hose

VERSION 02 110 22

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 65 mm C = 95 mm
Force A B *C D F G L For vacuum cup Weight Weight Weight
Item
Kg Ø Ø item g g g
02 110 22 23.74 26 46 28 110 M20 61 139 08 110 40 M8 603 654 683
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 65 mm and 95 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.101
BASIC ANTI-ROTATION VACUUM CUP HOLDERS

The technical features are the same as for the previously

described basic vacuum cup holders. Their distinctive features
are their brass stem with hexagonal cross-section and the steel
drive bush, also with hexagonal hole.
3D drawings are available on vuototecnica.net

This structure prevents the stem and, as a consequence, the

cup assembled onto it from rotating on its axis.
The drive bush is equipped with two fine thread ring nuts
to guarantee an accurate fastening of the cup holder to the
automation.
They are suited for cups with diameters between 45 mm
and 110 mm, although they have been specially designed for
assembling rectangular, concave or elliptical cups.
The actual springing stroke is:
- For height C= 28 mm 16 mm
- For height C= 65 mm 49 mm
- For height C= 95 mm 74 mm

For Ø 6 int. hose

Hex. 13 Ring nut KM4 Sp17

VERSION 02 95 . . VERSION 02 95 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D E F G L Weight
Item
Ø Ø g
02 95 28 32 40 28 M12 15 M20 x 1 10 125 180
02 95 65 32 40 65 M12 15 M20 x 1 10 162 225
02 95 95 32 40 95 M12 15 M20 x 1 10 192 246
02 95 28 1/4” 32 40 28 G1/4” 15 M20 x 1 10 125 181
02 95 65 1/4” 32 40 65 G1/4” 15 M20 x 1 10 162 226
02 95 95 1/4” 32 40 95 G1/4” 15 M20 x 1 10 192 247
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.102
BASIC VACUUM CUP HOLDERS FIX

These are simple nickel-plated brass threaded bushes with ring

nuts for height adjustment and with male and female threaded
ends, one to assemble the vacuum cup with support and the
other for the quick coupling connecting the suction hose.

3D drawings are available on vuototecnica.net

For Ø 6 int. hose
Sp17

Ring nut KM4

VERSION 02 91 01 VERSION 02 91 01 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
D E F L Weight
Item
Ø Ø g
02 91 01 G1/4” 10 M20 x 1 74 162
Note: To order vacuum cup holders with L fittings, add the letter L to the code.
For Ø 6 int. hose

Sp17
Ring nut KM4

VERSION 02 91 . . VERSION 02 91 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
D E F L Weight
Item
Ø Ø g
02 91 05 G1/4” 10 M20 x 1 84 170
02 91 06 G3/8” 10 M20 x 1 84 174
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
2.103
SPECIAL VACUUM CUP HOLDERS

These special vacuum cup holders have been designed to

lift and handle heavy loads and to withstand heavy-duty and
continuous workloads in dusty or damp environments. They
are composed of:
3D drawings are available on vuototecnica.net

- A chrome-plated steel stem for fastening the cup

- A brass threaded support with self-lubricating bushes,
equipped with two ring nuts for fastening the cup holder to
the automation
- A spring to cushion the impact of the cup with the load to be
lifted
- A quick coupling for connection with the suction hose
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

Vacuum
2 cup

Support

Vacuum
For Ø 6 int. hose

cup

Sp17

Support Ring nut KM7

VERSION 06 85 10 VERSION 06 85 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item g g
06 85 10 14.18 46 39 55 85 M35 x 1.5 50 190 01 85 10 00 08 29 731.9 853.9
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Support

Vacuum
For Ø 6 int. hose

cup

Sp17

Support Ring nut KM7

VERSION 06 85 15 VERSION 06 85 15 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item g g
06 85 15 14.18 22 39 55 85 M35 x 1.5 50 166 01 85 15 00 08 32 779.7 899.7
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Support Ring nut

Vacuum
For Ø 6 int. hose

cup

Sp17

Ring nut
Ring nut KM7
Support

VERSION 06 90 24 VERSION 06 90 24 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Ring nut included Weight Weight
Item
Kg Ø Ø item item item g g
06 90 24 15.89 29 39 55 90 M35 x 1.5 50 173 01 90 24 00 08 110 00 08 111 852.8 974.8
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum 2
cup

For Ø 6 int. hose

Vacuum
cup
Sp17

Ring nut KM7

VERSION 06 100 40 VERSION 06 100 40 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Weight Weight
Item
Kg Ø Ø item g g
06 100 40 19.62 31 39 55 100 M35 x 1.5 50 175 08 100 40 736 858
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

2 Vacuum
cup

For Ø 6 int. hose

Vacuum
cup
Sp17

Ring nut KM7

VERSION 06 100 50 VERSION 06 100 50 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Weight Weight
Item
Kg Ø Ø item g g
06 100 50 19.62 35.5 39 55 100 M35 x 1.5 50 179.5 08 100 50 732 854
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Support

Vacuum
cup
For Ø 6 int. hose

Sp17

Ring nut KM7

Support

VERSION 06 110 10 VERSION 06 110 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item g g
06 110 10 23.74 22 39 55 114 M35 x 1.5 50 166 01 110 10 00 08 33 912.3 1034.3
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Cap

Vacuum
cup
For Ø 6 int. hose

Sp17

Ring nut KM7

Cap

VERSION 06 110 15 VERSION 06 110 15 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Cap included Weight Weight
Item
Kg Ø Ø item item g g
06 110 15 23.74 31 39 55 110 M35 x 1.5 50 175 08 110 15 00 11 06 980 1100
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup
2

Support Ring nut

For Ø 6 int. hose

Vacuum
cup

Sp17

Ring nut
Ring nut KM7
Support

VERSION 06 110 24 VERSION 06 110 24 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Ring nut included Weight Weight
Item
Kg Ø Ø item item item Kg Kg
06 110 24 23.74 29 39 55 110 M35 x 1.5 50 173 01 110 24 00 08 110 00 08 111 1.07 1.19
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Support

Vacuum
cup
For Ø 6 int. hose

Sp17

Ring nut KM7

Support

VERSION 06 150 10 VERSION 06 150 10 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 150 10 45.00 28 39 55 154 M35 x 1.5 50 172 01 150 10 00 08 35 1.32 1.45
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Support
Ring nut

Vacuum
cup
For Ø 6 int. hose

Sp17

Ring nut Ring nut KM7

Support

VERSION 06 150 36 VERSION 06 150 36 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Ring nut included Weight Weight
Item
Kg Ø Ø item item item Kg Kg
06 150 36 45.00 41 39 55 150 M35 x 1.5 50 185 01 150 36 00 08 112 00 08 113 1.39 1.52
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Ring nut KM7

For Ø 9 int. hose

For Ø 16 int. hose

VERSION 06 . . . 10

VACUUM CUP HOLDERS WITH HOSE-END FITTING FOR PLASTIC HOSE Ø 16 X 18 C = 110 mm
Force A B *C D F G L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 300 10 176.6 31 89 55 300 M35 x 1.5 61 149 08 300 10 5.42 5.56
06 350 10 240.0 31 89 55 350 M35 x 1.5 61 149 08 350 10 7.30 7.43
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.117
SPECIAL VACUUM CUP HOLDERS FOR BELLOWS CUPS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Support For Ø 9 int. hose

Vacuum
cup
Sp19

Support

Ring nut KM7

VERSION 06 75 42 VERSION 06 75 42 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 75 42 11.93 42 45 55 78 M35 x 1.5 50 197 01 75 42 00 08 143 0.76 0.87
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.118
SPECIAL VACUUM CUP HOLDERS FOR BELLOWS CUPS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Cap

Vacuum
For Ø 9 int. hose

cup

Sp19

Cap
Ring nut KM7

VERSION 06 . . . 30 VERSION 06 . . . 30 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F G L For vacuum cup Cap included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 110 30 23.74 45 45 55 110 M35 x 1.5 50 200 08 110 30 00 11 44 0.97 1.08
06 150 30 45.00 60 45 55 150 M35 x 1.5 50 215 08 150 30 00 11 44 1.09 1.20
06 180 30 63.50 70 45 55 180 M35 x 1.5 50 225 08 180 30 00 11 44 1.45 1.56
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.119
SPECIAL VACUUM CUP HOLDERS FOR BELLOWS CUPS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum Support
cup

Cap
For Ø 9 int. hose

Support
Sp19

Cap Ring nut KM7

Vacuum
cup

VERSION 06 110 58 VERSION 06 110 58 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Cap included Weight Weight
Item
Kg Ø Ø item item item Kg Kg
06 110 58 23.74 58 45 55 110 M35 x 1.5 50 213 01 110 58 00 08 162 00 11 44 0.93 1.04
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.120
SPECIAL VACUUM CUP HOLDERS FOR BELLOWS CUPS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup Support

Cap
For Ø 9 int. hose

Support

Sp19

Ring nut KM7

Cap

Vacuum
cup

VERSION 06 150 74 VERSION 06 150 74 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F G L For vacuum cup Support included Cap included Weight Weight
Item
Kg Ø Ø item item item Kg Kg
06 150 74 45.00 74 45 55 150 M35 x 1.5 50 229 01 150 74 00 08 163 00 11 44 1.34 1.45
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.121
SPECIAL VACUUM CUP HOLDERS FOR BELLOWS CUPS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Cap
For Ø 9 int. hose

Sp19

Ring nut KM7

Cap

Vacuum
cup

VERSION 06 250 30 VERSION 06 250 30 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F G L For vacuum cup Cap included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 250 30 122.60 100 45 55 250 M35 x 1.5 50 255 08 250 30 00 18 33 2.20 2.31
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.122
SPECIAL VACUUM CUP HOLDERS WITH MALE AND FEMALE THREADED CONNECTORS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Special vacuum cup holders
with male threaded connectors

For Ø 6 int. hose

Sp17

Ring nut KM7

2
VERSION 06 12 . . M VERSION 06 12 . . M L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
*C F L Weight
Item
Ø Kg
06 12 55 M 55 M35 x 1.5 160 0.63
06 12 110 M 110 M35 x 1.5 215 0.77
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

Special vacuum cup holders with female threaded connectors

For Ø 6 int. hose

Sp17

Ring nut KM7

VERSION 06 12 . . VERSION 06 12 . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
*C F L Weight
Item
Ø Kg
06 12 55 55 M35 x 1.5 164 0.62
06 12 110 110 M35 x 1.5 219 0.75
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.123
SPECIAL VACUUM CUP HOLDERS WITH MALE THREADED CONNECTORS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

For int. hose

Sp17

2 Ring nut KM7

VERSION 06 . . . . M VERSION 06 . . . . M L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE
A *C F L M Int. hose Weight
Item
Ø Ø Kg
06 11 55 M M12 55 M35 x 1.5 159 G1/4” 6 0.63
06 11 110 M M12 110 M35 x 1.5 214 G1/4” 6 0.77
06 13 55 M G1/2” 55 M35 x 1.5 159 G3/8” 9 0.63
06 13 110 M G1/2” 110 M35 x 1.5 214 G3/8” 9 0.77
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

Ring nut KM7

VERSION 06 . . . . M

A *C F L Weight
Item
Ø Kg
06 14 55 M M16 55 M35 x 1.5 129 0.52
06 14 110 M M16 110 M35 x 1.5 184 0.65
06 15 55 M M12 55 M35 x 1.5 129 0.52
06 15 110 M M12 110 M35 x 1.5 184 0.65
Note: The vacuum cup holder is not equipped with an axial vacuum passage

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.124
SPECIAL VACUUM CUP HOLDERS WITH PLUNGER VALVE

They share the same mechanical features at the special vacuum cup
holders. The addition of a plunger valve solidly connected to a conical
spear valve, which activates suction, and therefore creates vacuum,
only when the cup comes into contact with the load to be lifted.

3D drawings are available on vuototecnica.net

With these cup holders, it is no longer necessary to install cocks on
the suction hoses; for this reason, they are recommended in all those
cases in which there is a chance that not all the cups come into
contact with the load to be lifted (because of an uneven or incomplete
load).
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

Vacuum
cup
2

Screw

Disc
For Ø 6 int. hose

Vacuum
cup
Sp22 Sp17

Screw
Ring nut KM7
Disc

VERSION 06 85 20 VERSION 06 85 20 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Screw included Disc included Weight Weight
Item
Kg Ø Ø item item item Kg Kg

06 85 20 14.18 81 55 85 M35 x 1.5 225 01 85 10 00 20 13 00 03 22 0.83 0.95

Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Disc Support
For Ø 6 int. hose

Vacuum
cup
Sp22 Sp17

Support Ring nut KM7

Disc

VERSION 06 85 22 VERSION 06 85 22 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Support included Disc included Weight Weight
Item
Kg Ø Ø item item item Kg Kg
06 85 22 14.18 65 55 85 M35 x 1.5 209 01 85 15 00 08 32 00 03 22 0.89 1.01
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Disc Support

Vacuum
For Ø 6 int. hose

cup

Sp22 Sp17

Ring nut KM7

Support
Disc

VERSION 06 110 20 VERSION 06 110 20 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Support included Disc included Weight Weight
Item
Kg Ø Ø item item item Kg Kg
06 110 20 23.74 65 55 114 M35 x 1.5 209 01 110 10 00 08 33 00 03 22 1.02 1.14
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Cap

Vacuum
cup
For Ø 6 int. hose

Sp22 Sp17

Ring nut KM7

Cap

VERSION 06 110 22 VERSION 06 110 22 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Cap included Weight Weight
Item
Kg Ø item item Kg Kg
06 110 22 23.74 74 55 110 M35 x 1.5 218 08 110 15 00 11 06 1.48 1.56
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Disc Support

Vacuum
cup
For Ø 6 int. hose

Sp22 Sp17

Ring nut KM7

Support

Ring
nut KM7
For Ø 9 int. hose

Sp17

VERSION 06 . . . 20

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 300 20 176.6 31 89 55 300 M35 x 1.5 149 08 300 10 5.56 5.69
06 350 20 240.0 31 89 55 350 M35 x 1.5 149 08 350 10 7.42 7.55
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.131
SPECIAL VACUUM CUP HOLDERS WITH BUILT-IN SHUT-OFF VALVE

Along with all the other features they share with the other special cup
holders, these also have a built-in shut-off valve.
The purpose of the shut-off valve is to automatically close suction
when the cup is not in contact with the surface of the load to be
3D drawings are available on vuototecnica.net

handled or in case of a faulty grip or of considerable transpiration.

This thus prevents the reduction of the level of vacuum on the
remaining cups of the system which are regularly handling the load.
The clear advantage of this system is that the positioning or the
exclusion of the non-gripping cups are no longer binding.
Cups with diameters between 85 mm and 150 mm can be assembled
onto these cup holders, as long as they are provided with a threaded
3/8” gas female support.
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

For Ø 6 int. hose

Sp17

Ring nut KM7

VERSION 06 . . . . . VERSION 06 . . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8
A B C D F L Weight
Item
Ø Ø Kg
06 99 55 16 11 55 G3/8” M35 x 1.5 160 0.63
06 99 110 16 11 110 G3/8” M35 x 1.5 215 0.77
Minimum trigger flow = 4 m3/h Minimum level of vacuum = -250 mbar
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.132
SPECIAL ARTICULATED VACUUM CUP HOLDERS

The distinctive feature of these cup holders is their articulated

joint in hardened steel, which allows the flat cups installed on
these cup holders to adapt themselves to the loads to be lifted
even if not completely parallel with the cup plane, as well as to

3D drawings are available on vuototecnica.net

compensate possible verticality errors that can arise between
the cup holder and the automation fixing support.
Their technical and mechanical features are the same as the
other previously described special vacuum cup holders.
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

Vacuum Support
cup

Vacuum
cup
Support

Sp12

Sp19

Ring nut KM7

For Ø 6 int. hose

VERSION 06 110 12

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 110 12 23.74 26 77 55 114 M35 x 1.5 195 01 110 10 00 06 14 1.15 1.27
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.133
SPECIAL ARTICULATED VACUUM CUP HOLDERS

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

2
Vacuum
cup

Vacuum
cup
Sp12

Sp19
For Ø 6 int. hose

Ring nut KM7

VERSION 06 110 17

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 110 17 23.74 26 86 55 110 M35 x 1.5 204 08 110 15 1.22 1.34
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum Support
cup

Vacuum
cup
Support

Sp12

Sp19
Ring nut KM7
For Ø 6 int. hose

VERSION 06 150 12

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 150 12 45.00 30 83 55 154 M35 x 1.5 201 01 150 10 00 06 15 1.56 1.69
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup
2

Vacuum
cup

Sp12

Sp19
Ring nut KM7
For Ø 9 int. hose

VERSION 06 . . . . .

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 150 17 45.00 40.0 86 55 150 M35 x 1.5 204 08 150 15 1.73 1.85
06 200 12 78.50 47.5 88 55 200 M35 x 1.5 206 08 200 10 2.63 2.75
06 250 12 122.60 72.5 88 55 250 M35 x 1.5 206 08 250 10 3.89 4.02
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.136
SPECIAL ARTICULATED
VACUUM CUP HOLDERS
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum Support
cup

Support

Vacuum
cup

Sp12

Sp19
Ring nut KM7
For Ø 9 int. hose

VERSION 06 220 12 . .

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 220 12 OF 63.60 70 97 55 220 M35 x 1.5 215 01 220 10 OF 00 08 37 2.08 2.21
06 220 12 NF 63.60 70 97 55 220 M35 x 1.5 215 01 220 10 NF 00 08 37 2.07 2.20
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.137
SPECIAL ARTICULATED
VACUUM CUP HOLDERS
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum Support
cup

Support

Vacuum
cup Sp12

Sp19
Ring nut KM7
For Ø 9 int. hose

VERSION 06 220 12 A

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 220 12 A 78.50 70 80 55 220 M35 x 1.5 198 01 220 10 A 00 08 37 2.03 2.16
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.138
SPECIAL ARTICULATED
VACUUM CUP HOLDERS
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Sp19

Sp30

Ring nut KM7

For Ø 16 int. hose

VERSION 06 . . . 12

VACUUM CUP HOLDERS WITH HOSE-END FITTING FOR PLASTIC HOSE Ø 16 X 18 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 300 12 176.6 89 115 55 300 M35 x 1.5 233 08 300 10 6.09 6.22
06 350 12 240.0 89 115 55 350 M35 x 1.5 233 08 350 10 7.95 8.08
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.139
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITHOUT GS ARTICULATED JOINT

Unlike the ones previously described, these special articulated

vacuum cup holders have an articulated joint housed in the cup
support. This has allowed a reduction of the overall dimensions
without affecting performance.
3D drawings are available on vuototecnica.net

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

Vacuum Support
cup

Vacuum
cup

Sp22
se
. ho
int Ring nut KM7
6
rØ
Fo

VERSION 06 110 32

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 110 32 23.74 33 42.5 55 114 M35 x 1.5 160.5 01 110 10 00 06 62 1.15 1.27
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.140
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITHOUT GS ARTICULATED JOINT

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Support 2

Vacuum
cup

Sp22 e
os
t.h
in Ring nut KM7
6
rØ
Fo

Support

VERSION 06 150 32

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 150 32 45.00 39 48.5 55 154 M35 x 1.5 166.5 01 150 10 00 06 49 1.63 1.76
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.141
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH COMPACT STROKE

Marble and glass sheets are usually handled with cups that take them
from a horizontal plane and place them vertically or vice-versa.
These special cup holders with compact stroke have been designed to
minimise the lever forces between the cup and the automation fixing bush
3D drawings are available on vuototecnica.net

during the rotation of the sheets, as well as their sliding on the cups.
They share all the technical features of the other previously described
special cup holders but their overall dimensions are reduced to minimum
by housing the articulated joint in the cup support, thus reducing the steel
stem and the spring stroke length and modifying the brass bush, in order
to allow it to be screwed directly onto the automation.
Moreover, a special non-slip plastic coating fixed onto the cup support
prevents the lifted load from slipping.
The actual springing stroke is:
- For height C= 29 mm 13 mm

Vacuum
cup

Support
2

Swivel L fitting
G1 / 8 “

Non-slip
coating For Ø 6 ext. hose

Vacuum
cup

Support

Sp30

VERSION 06 110 42

VACUUM CUP HOLDERS WITH L QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6

Force B C D E L For vacuum cup Support included Weight
Item
Kg Ø Ø item item Kg
06 110 42 23.74 17 29 114 13 83.5 01 110 10 M 00 06 59 0.49
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.142
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH COMPACT STROKE

The actual springing stroke is:

- For height C= 29 mm 13 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Non-slip
coating
Support
2

Swivel L fitting
G1 / 8 “

For Ø 8 ext. hose

Vacuum
cup

Support

Sp30

VERSION 06 127 42

VACUUM CUP HOLDERS WITH L QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8

Force B C D E L For vacuum cup Support included Weight
Item
Kg Ø Ø item item Kg
06 127 42 17.50 26.7 29 127 13.5 93.2 01 127 15 00 06 61 0.76
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.143
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH COMPACT STROKE

The actual springing stroke is:

- For height C= 29 mm 13 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Support

Swivel L fitting
G1 / 8 “

Non-slip
For Ø 6 ext. hose
coating
Vacuum
cup

Support

Sp30

VERSION 06 150 42

VACUUM CUP HOLDERS WITH L QUICK COUPLER FOR PLASTIC HOSE Ø 4 X 6

Force B C D E L For vacuum cup Support included Weight
Item
Kg Ø Ø item item Kg
06 150 42 45.00 23 29 154 13 89.5 01 150 10 M 00 06 60 0.94
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.144
SPECIAL STAINLESS STEEL ANTI-ROTATION VACUUM CUP HOLDERS

Designed for the robot-automotive sector, these cup holders offer

ideal solutions to various handling problems that arise in all industrial
sectors.
In addition the characteristics of the previously described special

3D drawings are available on vuototecnica.net

vacuum cup holders, their distinctive features are their brass stem
with hexagonal cross-section and the steel drive bush, also with
hexagonal hole. This structure prevents the stem and, as a result, the
cup assembled onto it from rotating on its axis.
The drive bush is equipped with two fine thread ring nuts to guarantee
an accurate fastening of the cup holder to the automation. Moreover,
the two ends of the stem, also in stainless steel, are threaded male
or female and interchangeable. The straight quick coupler for the
connection to the suction hose is screwed to one end, while the cup
with support is assembled onto the other end.
They are suited for cups with a diameter between 40 mm and
200 mm, although they are especially useful for the assembly of
rectangular or elliptical vacuum cups.
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

For Ø d int. hose

Hex. 16

Sp22 Sp22

Ring nut KM5

VERSION 06 . . . . . VERSION 06 . . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE
A B C D d E F L M N O RL RM Weight
Item
Ø Ø Ø Ø g
06 55 80 13 34 55 G1/4” 6 G1/4” M25 x 1.5 142 21.0 32.0 18.5 G1/4” G1/4” 318
06 55 81 15 40 55 G3/8” 9 G3/8” M25 x 1.5 150 21.5 35.5 22.0 G3/8” G3/8” 330
06 55 82 15 34 55 G3/8” 6 G1/4” M25 x 1.5 144 21.0 32.0 18.5 G1/4” G1/4” 320
06 110 80 13 34 110 G1/4” 6 G1/4” M25 x 1.5 197 21.0 32.0 18.5 G1/4” G1/4” 386
06 110 81 15 40 110 G3/8” 9 G3/8” M25 x 1.5 205 21.5 35.5 22.0 G3/8” G3/8” 398
06 110 82 15 34 110 G3/8” 6 G1/4” M25 x 1.5 199 21.0 32.0 18.5 G1/4” G1/4” 388
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.145
SPECIAL ANTI-ROTATION VACUUM CUP HOLDERS WITH MALE THREADED
CONNECTOR
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

For Ø d int. hose

Hex. 16

Sp22 Sp22

Ring nut KM5

VERSION 06 . . . . . VERSION 06 . . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE
A B C D d E F L M N O RL RM Weight
Item
Ø Ø Ø Ø g
06 55 90 15 34 55 G1/4” 6 G1/4” M25 x 1.5 144 21.0 32.0 18.5 G1/4” G1/4” 314
06 55 91 15 34 55 G3/8” 6 G1/4” M25 x 1.5 144 21.0 32.0 18.5 G1/4” G1/4” 320
06 55 92 15 40 55 G3/8” 9 G3/8” M25 x 1.5 150 21.5 35.5 22.0 G3/8” G3/8” 330
06 55 93 15 40 55 G1/2” 9 G3/8” M25 x 1.5 150 21.5 35.5 22.0 G3/8” G3/8” 332
06 55 94 15 34 55 M12 6 G1/4” M25 x 1.5 144 21.0 32.0 18.5 G1/4” G1/4” 318
06 55 95 15 40 55 M12 9 G3/8” M25 x 1.5 150 21.5 35.5 22.0 G3/8” G3/8” 328
06 55 96 15 40 55 M16 9 G3/8” M25 x 1.5 150 21.5 35.5 22.0 G3/8” G3/8” 330
06 110 90 15 34 110 G1/4” 6 G1/4” M25 x 1.5 199 21.0 32.0 18.5 G1/4” G1/4” 374
06 110 91 15 34 110 G3/8” 6 G1/4” M25 x 1.5 199 21.0 32.0 18.5 G1/4” G1/4” 380
06 110 92 15 40 110 G3/8” 9 G3/8” M25 x 1.5 205 21.5 35.5 22.0 G3/8” G3/8” 390
06 110 93 15 40 110 G1/2” 9 G3/8” M25 x 1.5 205 21.5 35.5 22.0 G3/8” G3/8” 392
06 110 94 15 34 110 M12 6 G1/4” M25 x 1.5 199 21.0 32.0 18.5 G1/4” G1/4” 378
06 110 95 15 40 110 M12 9 G3/8” M25 x 1.5 205 21.5 35.5 22.0 G3/8” G3/8” 388
06 110 96 15 40 110 M16 6 G3/8” M25 x 1.5 205 21.5 35.5 22.0 G3/8” G3/8” 390
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.146
SPECIAL ANTI-ROTATION VACUUM CUP HOLDERS WITH SPHERICAL SWIVEL
SUPPORT
In addition the characteristics of the previously described
special anti-rotation vacuum cups, these cup holders are
provided with a nylon spherical swivel support which allows to
place and keep the cup in the desired place.

3D drawings are available on vuototecnica.net

Their fixing support is made with aluminium and is composed
of two parts that, screwed together, allow to block the spherical
joint, thus keeping the vacuum cup holder in place.
They are suited for cups with a diameter between 40 mm and
200 mm, although they are especially useful for the assembly
of rectangular or elliptical vacuum cups.
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

For Ø d int. hose

Sp22

Hex. 16

Sp22

VERSION 06 . . . . . VERSION 06 . . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE
A B C D d E L M N O RL RM Weight
Item
Ø Ø Ø g
06 55 100 13 34 55 G1/4” 6 G1/4” 142 21.0 32.0 18.5 G1/4” G1/4” 338
06 55 101 15 40 55 G3/8” 9 G3/8” 150 21.5 35.5 22.0 G3/8” G3/8” 350
06 55 102 15 34 55 G3/8” 6 G1/4” 144 21.0 32.0 18.5 G1/4” G1/4” 340
06 110 100 13 34 110 G1/4” 6 G1/4” 197 21.0 32.0 18.5 G1/4” G1/4” 406
06 110 101 15 40 110 G3/8” 9 G3/8” 205 21.5 35.5 22.0 G3/8” G3/8” 418
06 110 102 15 34 110 G3/8” 6 G1/4” 199 21.0 32.0 18.5 G1/4” G1/4” 408
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.147
SPECIAL ANTI-ROTATION VACUUM CUP HOLDERS WITH SPHERICAL SWIVEL
SUPPORT
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

For Ø d int. hose

Sp22

Hex. 16

Sp22

VERSION 06 . . . . . VERSION 06 . . . . . L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE
A B C D d E L M N O RL RM Weight
Item
Ø Ø Ø g
06 55 110 15 34 55 G1/4” 6 G1/4” 144 21.0 32.0 18.5 G1/4” G1/4” 334
06 55 111 15 34 55 G3/8” 6 G1/4” 144 21.0 32.0 18.5 G1/4” G1/4” 340
06 55 112 15 40 55 G3/8” 9 G3/8” 150 21.5 35.5 22.0 G3/8” G3/8” 350
06 55 113 15 40 55 G1/2” 9 G3/8” 150 21.5 35.5 22.0 G3/8” G3/8” 352
06 55 114 15 34 55 M12 6 G1/4” 144 21.0 32.0 18.5 G1/4” G1/4” 338
06 55 115 15 40 55 M12 9 G3/8” 150 21.5 35.5 22.0 G3/8” G3/8” 348
06 55 116 15 40 55 M16 9 G3/8” 150 21.5 35.5 22.0 G3/8” G3/8” 350
06 110 110 15 34 110 G1/4” 6 G1/4” 199 21.0 32.0 18.5 G1/4” G1/4” 394
06 110 111 15 34 110 G3/8” 6 G1/4” 199 21.0 32.0 18.5 G1/4” G1/4” 400
06 110 112 15 40 110 G3/8” 9 G3/8” 205 21.5 35.5 22.0 G3/8” G3/8” 410
06 110 113 15 40 110 G1/2” 9 G3/8” 205 21.5 35.5 22.0 G3/8” G3/8” 412
06 110 114 15 34 110 M12 6 G1/4” 199 21.0 32.0 18.5 G1/4” G1/4” 398
06 110 115 15 40 110 M12 9 G3/8” 205 21.5 35.5 22.0 G3/8” G3/8” 408
06 110 116 15 40 110 M16 9 G3/8” 205 21.5 35.5 22.0 G3/8” G3/8” 410
Note: To order vacuum cup holders with L fittings, add the letter L to the code.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.148
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

All the special vacuum cup holders previously described can be

provided in the double springing version.
The cup holder fixing bush is located between two springs: the
lower one cushions the impact of the cup with the load to be

3D drawings are available on vuototecnica.net

lifted during the approach phase, while the upper one cushions
the impact of the bush with the cup holder end and gradually
loads the cup during the lifting phase.
These cup holders are especially recommended when the load
to be lifted is very heavy, rough or not perfectly flat.
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

Vacuum
cup
2

Support
For Ø 6 int. hose

Vacuum
cup
Sp17

Support

Ring nut KM7

VERSION 06 85 13 VERSION 06 85 13 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 85 13 14.18 46 55 85 M35 x 1.5 245 01 85 10 00 08 29 0.87 0.99
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.149
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Support
For Ø 6 int. hose

Vacuum
cup
Sp17

Support
Ring nut KM7

VERSION 06 85 17 VERSION 06 85 17 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 85 17 14.18 22 55 85 M35 x 1.5 221 01 85 15 00 08 32 0.90 1.04
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.150
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

2
Vacuum
cup

Support

Vacuum
For Ø 6 int. hose

cup

Sp17

Support

Ring nut KM7

VERSION 06 110 13 VERSION 06 110 13 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 110 13 23.74 22 55 114 M35 x 1.5 221 01 110 10 00 08 33 1.05 1.18
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.151
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
2 cup

cap
For Ø 6 int. hose

Vacuum
cup
Sp17

Ring nut KM7

Cap

VERSION 06 110 16 VERSION 06 110 16 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Cap included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 110 16 23.74 31 55 110 M35 x 1.5 230 08 110 15 00 11 06 1.12 1.25
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.152
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup

Support

Vacuum
cup
For Ø 6 int. hose

Sp17

Ring nut KM7

Support

VERSION 06 150 13 VERSION 06 150 13 L

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 150 13 45.00 28 55 154 M35 x 1.5 227 01 150 10 00 08 35 1.46 1.58
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
To order vacuum cup holders with L fittings, add the letter L to the code.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.153
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

2 Vacuum
cup

Vacuum
cup

Ring
nut KM7
For Ø 9 int. hose

VERSION 06 . . . . .

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 150 18 45.0 26 40.0 55 150 M35 x 1.5 199 08 150 15 1.65 1.79
06 200 13 78.5 28 47.5 55 200 M35 x 1.5 201 08 200 10 2.55 2.69
06 250 13 122.6 28 72.5 55 250 M35 x 1.5 201 08 250 10 3.82 3.96
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.154
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum Support
cup

Ring
nut KM7
For Ø 9 int. hose

VERSION 06 220 13 . . .

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 220 13 OF 63.6 35 70 55 220 M35 x 1.5 208 01 220 10 OF 00 08 37 2.01 2.15
06 220 13 NF 63.6 35 70 55 220 M35 x 1.5 208 01 220 10 NF 00 08 37 2.00 2.14
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.155
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum Support
cup

Ring nut KM7

For Ø 9 int. hose

VERSION 06 220 13 A

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 220 13 A 78.5 20 70 55 220 M35 x 1.5 193 01 220 10 A 00 08 37 1.96 2.09
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.156
SPECIAL VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum 2
cup

Vacuum
cup

Ring
nut KM7
For Ø 16 int. hose

VERSION 06 . . . 13

VACUUM CUP HOLDERS WITH HOSE-END FITTING FOR PLASTIC HOSE Ø 16 X 18 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 300 13 176.6 31 89 55 300 M35 x 1.5 204 08 300 10 5.57 5.70
06 350 13 240.0 31 89 55 350 M35 x 1.5 204 08 350 10 7.43 7.57
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.157
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The distinctive feature of these cup holders is their

articulated joint in hardened steel, which allows the flat
cups installed on these cup holders to adapt themselves
to the loads to be lifted even if not completely parallel
3D drawings are available on vuototecnica.net

with the cup plane, as well as to compensate possible

verticality errors that can arise between the cup holder
and the automation fixing support.
The cup holder fixing bush is located between two
springs: the lower one cushions the impact of the cup
with the load to be lifted during the approach phase,
while the upper one cushions the impact of the bush
with the cup holder end and gradually loads the cup
during the lifting phase.
These cup holders are especially recommended when the
load to be lifted is very heavy, rough or not perfectly flat.
The actual springing stroke is:
- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

Vacuum
2 cup

Vacuum
cup
Support

Sp12

Sp19
Ring nut KM7
For Ø 6 int. hose

VERSION 06 110 14

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 110 14 23.74 26 77 55 114 M35 x 1.5 250 01 110 10 00 06 14 1.29 1.39
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.158
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
cup
2

Vacuum
cup

Sp12

Sp19
Ring nut KM7
For Ø 6 int. hose

VERSION 06 110 18

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 110 18 23.74 26 86 55 110 M35 x 1.5 259 08 110 15 1.36 1.46
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.159
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum Support
cup

Vacuum
cup
Support

Sp12

Sp19
Ring nut KM7
For Ø 6 int. hose

VERSION 06 150 14

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 6 X 8 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 150 14 45.00 30 83 55 154 M35 x 1.5 256 01 150 10 00 06 15 1.71 1.81
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.160
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum
2
cup

Vacuum
cup

Sp12

Sp19
Ring nut KM7
For Ø 9 int. hose

VERSION 06 . . . . .

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D E F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 150 19 45.00 40.0 86 55 150 50 M35 x 1.5 259 08 150 15 1.86 1.97
06 200 14 78.50 47.5 88 55 200 52 M35 x 1.5 261 08 200 10 2.77 2.87
06 250 14 122.60 72.5 88 55 250 52 M35 x 1.5 261 08 250 10 4.03 4.14
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.161
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum Support
cup

Support
Vacuum
cup

Sp12

Sp19

Ring nut KM7

For Ø 9 int. hose

VERSION 06 220 14 . . .

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 220 14 OF 63.6 70 97 55 220 M35 x 1.5 270 01 220 10 OF 00 08 37 2.22 2.32
06 220 14 NF 63.6 70 97 55 220 M35 x 1.5 270 01 220 10 NF 00 08 37 2.21 2.31
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.162
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm

3D drawings are available on vuototecnica.net

Vacuum Support
cup

Support
Vacuum
cup

Sp12

Sp19

Ring nut KM7

For Ø 9 int. hose

VERSION 06 220 14 A

VACUUM CUP HOLDERS WITH STRAIGHT QUICK COUPLER FOR PLASTIC HOSE Ø 9 X 12 C = 110 mm
Force A B *C D F L For vacuum cup Support included Weight Weight
Item
Kg Ø Ø item item Kg Kg
06 220 14 A 78.5 70 80 55 220 M35 x 1.5 253 01 220 10 A 00 08 37 2.17 2.27
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm

Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.163
SPECIAL ARTICULATED VACUUM CUP HOLDERS WITH DOUBLE SPRINGING

The actual springing stroke is:

- For height C= 55 mm 37 mm
- For height C= 110 mm 84 mm
3D drawings are available on vuototecnica.net

Vacuum
cup

Sp19

Sp30

Ring nut KM7

For Ø 16 int. hose

VERSION 06 . . . 14

VACUUM CUP HOLDERS WITH HOSE-END FITTING FOR PLASTIC HOSE Ø 16 X 18 C = 110 mm
Force A B *C D F L For vacuum cup Weight Weight
Item
Kg Ø Ø item Kg Kg
06 300 14 176.6 89 115 55 300 M35 x 1.5 288 08 300 10 6.24 6.63
06 350 14 240.0 89 115 55 350 M35 x 1.5 288 08 350 10 8.10 8.22
Note: The vacuum cups are not integral parts of the cup holders and, therefore, must be ordered separately.
* Also available with height C of 110 mm
Note: The force of the vacuum cups indicated in the table represents 1/3 of the value of the theoretical force calculated at a level of vacuum of -75 KPa and a factor of safety 3.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.164
SPHERICAL ARTICULATED JOINTS

Our spherical articulated joints are made with hardened steel.

Assembled to the cup holders, they compensate offsets,
orthogonality and flatness errors that often arise between the
cups and the surface of the load to be lifted.

3D drawings are available on vuototecnica.net

Sp7 Sp10
Hex. 17

2
A B C D E F L Weight
Item
Ø Ø g
GSM8 15 5 25 M8 4.5 M8 49.5 55

Sp12 Sp19
Hex. 30

A B C D E F L Weight
Item
Ø Ø g
GSM12 21 6.5 34.5 M12 8.5 M12 70.5 220

Sp19 Sp30
Sp41

A B C D E F L Weight
Item
Ø Ø g
GSM16 26.5 8 53 M16 10 M16 97.5 670

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.165
BALL JOINT COUPLINGS WITH AXIAL VACUUM CONNECTION

This series of couplings was designed to be installed on suckers with

support, especially those that are flat or that have little lip, in order to
allow them to easily adapt to the gripping surface of the load to be
picked up, even if not perfectly parallel to the plane of the sucker itself
3D drawings are available on vuototecnica.net

or to compensate for any perpendicularity errors that often occur

between the sucker holder and the fixing support of the automation.
The vacuum connection is axial and the hold is guaranteed by a
special seal,always in contact with the ball joint.
The sucker installed on them is free to rotate 360° degrees on its axis
and to tilt up to 15°.
The couplings are made entirely of brass, except for the ball pin and
its retention nut which are made of stainless steel.
They can be fastened to the sucker using either the female or male
threaded connection.

BALL JOINT COUPLINGS WITH AXIAL VACUUM CONNECTION

A B C D E F G H I L M N Material Max load Weight
Item
Ø Ø Ø Ø hex wr. hex admissible Kg g
GSL 1/8’’ 20 12 G1/8’’ G1/8’’ 8.5 8 11 43.0 12 22.5 18 4 brass/stainless steel 10.5 40
GSL 1/4’’ 20 16 G1/4’’ G1/4’’ 10.0 8 15 44.6 12 22.6 18 4 brass/stainless steel 19.6 56
GSL 3/8’’ 30 28 G3/8’’ G3/8’’ 13.0 13 26 63.3 15 35.3 28 6 brass/stainless steel 33.4 206
GSL 1/2’’ 30 28 G1/2’’ G1/2’’ 17.0 15 26 72.3 15 40.3 28 6 brass/stainless steel 51.5 232

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
2.166
POSITIONABLE BALL JOINT COUPLINGS WITH AXIAL VACUUM CONNECTION

The positionable ball joints couplings in anodised

aluminium allow the installed vacuum cups to be
rotated 360° and to be tilted by up to 35° in order to
properly position them with respect to the gripping

3D drawings are available on vuototecnica.net

surface on the object to be handled, while at the
same time ensuring a perfect grip and proper
suction through the joint itself.

POSITIONABLE BALL JOINT COUPLINGS WITH AXIAL VACUUM CONNECTION

A B C D d E F G H I L Material Max load Weight
Item
Ø Ø Ø Ø Ø admissible Kg g

GSV 1/8” 40 20 -- G1/8” G1/8” 11.5 10 24.5 51.5 20 7 aluminium 18.24 77.6
GSV 1/4” 45 25 -- G1/4” G1/4” 14.5 12 28.5 60.5 25 7 aluminium 23.54 126.7
GSV 3/8” 50 30 -- G3/8” G3/8” 14.0 12 34.5 69.5 25 10 aluminium 33.91 171.2
GSVF 1/8” 40 20 15 G1/8” G1/8” 11.5 10 24.5 51.5 20 7 aluminium 18.24 80.4
GSVF 1/4” 45 25 20 G1/4” G1/4” 14.5 12 28.5 60.5 25 7 aluminium 23.54 129.2
GSVF 3/8” 50 30 21 G3/8” G3/8” 17.0 12 34.5 69.5 25 10 aluminium 33.91 167.6

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
2.167
VACUUM CUP HOLDER FIXING SUPPORTS

The first two supports shown in this page are made

with stainless steel and are suited for fastening the
cup holder to the machine by means of a slotted
cylindrical pin or a spherical pin housed in the
3D drawings are available on vuototecnica.net

automation. The third support, on the other hand,

is made with aluminium and it is composed of two
parts that, screwed together, block the spherical
joint, allowing to keep the cup holder in the desired
position.

SUPPORTS WITH SLOTTED CYLINDRICAL PIN

A B D H By Weight
2 Item
Ø vacuum cup holders g
00 FCH 10 35 39.5 25.5 79.5 special anti-rotation 102
00 FCH 11 30 33.5 20.5 73.5 basic 90

SUPPORTS WITH SPHERICAL PIN

A B D H By Weight
Item
Ø vacuum cup holders g
00 FCH 20 35 39.5 25.5 79.5 special anti-rotation 168
00 FCH 21 30 33.5 20.5 73.5 basic 154

Hex. 16
Item Item

Item

SUPPORTS WITH BUILT-IN BALL JOINT COUPLING

By Weight
Item
vacuum cup holders g
FCH 16 special anti-rotation 156

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.168
VACUUM CUP HOLDER FIXING SUPPORTS

The supports described in the following in these

pages are made with galvanised sheet steel and
they are used to fasten the various types of cup
holders to the automation, generally made up of a

3D drawings are available on vuototecnica.net

square tube frame. The screw or the handle with
which they are equipped quickly block the support
in position.

SUPPORT FOR TUBE 30

Tube cross-sect. By Weight
Item
vacuum cup holders g
SFP 01 30 mini 160

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.169
VACUUM CUP HOLDER FIXING SUPPORTS
3D drawings are available on vuototecnica.net

SUPPORTS FOR TUBES 40-50

Tube cross-sect. A B C D E F G H L By Weight
Item
Ø vacuum cup holders g
SFP 02 40 40.2 23 23 21 56 106 60 99 159 basic 350
SFP 03 40 40.2 23 23 25 56 106 60 99 159 special anti-rotation 338
SFP 04 40 40.2 30 30 36 70 120 60 99 173 special 438
SFP 05 50 50.2 23 23 21 56 116 70 109 169 basic 370
SFP 06 50 50.2 23 23 25 56 116 70 109 169 special anti-rotation 377
SFP 07 50 50.2 30 30 36 70 130 70 109 183 special 490

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
2.170
VACUUM MEASUREMENT, CONTROL AND ADJUSTMENT
INSTRUMENTS

VACUUM AND PRESSURE UNIT CONVERSION TABLES PG. 3.00

VACUUM AND PRESSURE GAUGES PG. 3.01 ÷ 3.04

3D drawings are available on vuototecnica.net

VACUUM GAUGE WITH STEEL PUNCH PG. 3.05
MINI PNEUMATIC VACUUM SWITCHES PG. 3.06
MINI ELECTROMECHANICAL VACUUM SWITCH PG. 3.07
MICRO DIGITAL VACUUM SWITCHES PG. 3.08 ÷ 3.09
ANALOGUE VACUUM SWITCH PG. 3.10 ÷ 3.11
DIGITAL VACUUM AND PRESSURE SWITCHES PG. 3.12 ÷ 3.13
DIGITAL VACUUM SWITCHES PG. 3.14 ÷ 3.15
DIGITAL VACUUM AND PRESSURE SWITCHES PG. 3.16 ÷ 3.17
DIGITAL VACUUM AND PRESSURE SWITCHES WITH TWO-COLOUR DISPLAY PG. 3.18 ÷ 3.19
ACCESSORIES FOR ANALOGUE AND DIGITAL VACUUM AND PRESSURE SWITCHES PG. 3.20 ÷ 3.22
VACUUM ADJUSTMENT VALVES PG. 3.23
VACUUM REGULATORS PG. 3.24
REGULATORS FOR ROUGH VACUUM LEVELS PG. 3.25
VACUUM REGULATORS WITH PNEUMATIC ADJUSTMENT PG. 3.26
DIAGRAMS REFERRING TO THE LEVEL OF VACUUM ACCORDING TO THE SERVO-CONTROL SUPPLY PRESSURE PG. 3.27
SEALING KIT FOR VACUUM REGULATORS PG. 3.28

3
CONVERSION TABLES

VACUUM AND PRESSURE UNIT CONVERSION TABLES

mbar torr inch. Hg mmHg bar -KPa mbar
abs. abs. vacuum vacuum vacuum vacuum abs.
3D drawings are available on vuototecnica.net

PRESSURE MEASUREMENT UNIT CONVERSION FACTORS

(ABSOLUTE VALUES)

PRESSURE MEASUREMENT UNIT CONVERSION FACTORS (ABSOLUTE VALUES)

= mbar = bar = torr = inch. Hg = psi = atm = Kg/cm2 = mm H2O = m H2O = Pa
(Ibf/in2) (at) (N/m2)
mbar x 1 10-3 0,75 2,95x 10-2 14,5 x 10-3 9,87 x 10-4 1,02 x 10-3 10,2 1,02 x 10-2 100,0
bar x 1000,0 1 750,0 29,53 14,6 0,987 1,02 10197,0 10,19 100000
torr x 1,33 1,33 x 10-3 1 3,94 x 10-2 1,93 x 10-2 1,316 x 10-3 1,359 x 10-3 13,59 1,359 x 10-3 133,32
inch. Hg x 33,9 33,9 x 10-3 25,4 1 0,491 3,34 x 10-2 3,45 x 10-2 345,0 0,345 3386,0
psi (lbf/in2) x 68,9 6,89 x 10-2 51,7 2,04 1 6,8 x 10-2 7,03 x 10-2 703 0,703 6897
atm x 1013,25 1,013 760,0 30,0 14,696 1 1,033 10332 10,332 101325,0
Kg/cm2 (at) x 981 0,981 735,6 28,96 14,2 0,968 1 10000 10 98067,0
mm H2O x 9,81 x 10-2 9,81 x 10-5 7,35 x 10-2 2,89 x 10-3 1,42 x 10-3 9,67 x 10-5 10-4 1 10-3 9,8067
m H2O x 98,067 9,81 x 10-2 73,5 2,89 1,42 9,67 x 10-2 10 10000 1 9806,7
Pa (N/m2) x 0,01 10-5 7,5 x 10-3 2,95 x 10-4 1,45 x 10-4 9,87 x 10-6 1,02 x 10-5 0,102 1,02 x 10-4 1
Example: To transform 10 mbar in Torr = 10 x 0.75 = 7.5 Torr

3.00
VACUUM AND PRESSURE GAUGES

The measurement method of our vacuum gauges is based on the principle of the Bourdon
spring (Eugène Bourdon, France, 1808 – 1884).
It is made using section tubes in special copper alloy, one end is welded to the threaded
pin of the vacuum-pressure gauge, thus forming a single body with it, while the

3D drawings are available on vuototecnica.net

other closed end is free. As the vacuum or the pressure inside increases, it
tends to shift from the initial position (Bourdon effect). The movement of
the free end of the spring determines the vacuum-pressure measurement.
For easier reading, this movement is amplified by means of a connection
lever and transmitted to the pointer.
Everything is contained in a sturdy case made from different materials
according to the function of models, fastened onto a threaded fitting for
connection to the system. The face and index are visible thanks to a clear
plastic protective disc. They are available in various versions, with radial
or coaxial connectors, with built-in or external flange, dry or glycerine filled.
With the exception of the Ø 40 mm vacuum gauges, all other models have a
double scale dial.
All the vacuum and pressure gauges we will describe on these pages are
made in compliance with all the safety standards and measurement units in
force in the European Union.

Sp14
3

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Weight
Item
KPa scale error use material g
09 03 15 0 ÷ -100 -- 2.5% -10 °C ÷ +50 °C dry Black plastic 52

Sp14

PRESSURE GAUGES
Scale Double Scale Admissable Temperature of Notes Case Weight
Item
bar scale error use material g
09 03 20 0 ÷ 1.6 0 ÷ 23 psi 2.5% -10 °C ÷ +50 °C dry Black plastic 54
09 03 25 0 ÷ 10 0 ÷ 1.0 MPa 2.5% -10 °C ÷ +50 °C dry Black plastic 54

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.01
VACUUM GAUGES
3D drawings are available on vuototecnica.net

Sp14

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Weight
Item
3 mbar KPa scale error use material g
09 03 10 0 ÷ -1000 0 ÷ -100 2.5% -10 °C ÷ +50 °C dry black plastic 134

3 holes Ø 3.5
at 120°

Sp14

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Flange Weight
Item
mbar KPa scale error use material material g
09 01 10 0 ÷ -1000 0 ÷ -100 2.5% -10 °C ÷ +50 °C dry black plastic chrome-plated steel 162

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.02
VACUUM GAUGES

3D drawings are available on vuototecnica.net

3 holes Ø 3.5
at 120°

Sp14

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Flange Weight
Item
mbar KPa scale error use material material g 3
09 01 16 0 ÷ -1000 0 ÷ -100 1.6% -10 °C ÷ +50 °C in glycerine bath Die-cast brass chrome-plated steel 348

3 holes Ø 4.5
at 120°

Sp14

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case and flange Weight
Item
mbar KPa scale error use material g
09 02 10 0 ÷ -1000 0 ÷ -100 1% -10 °C ÷ +50 °C dry black steel 346

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.03
VACUUM GAUGES
3D drawings are available on vuototecnica.net

Sp14

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Weight
Item
3 mbar KPa scale error use material g
09 05 10 0 ÷ -1000 0 ÷ -100 2.5% -10 °C ÷ +50 °C dry black plastic 136

Sp14

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Weight
Item
mbar KPa scale error use material g
09 05 16 0 ÷ -1000 0 ÷ -100 1.6% -10 °C ÷ +50 °C in glycerine bath stainless steel 218

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.04
VACUUM GAUGE WITH STEEL PUNCH

This vacuum gauge with punch has been designed to allow the immediate
detection of the level of vacuum inside tin cans and food containers in
general.
The glycerine bath vacuum gauge item 09 05 16 used for this application

3D drawings are available on vuototecnica.net

(features described on the previous page) is provided with a hardened steel
punch to easily perforate the containers and with a vacuum cup in silicone
compound to guarantee vacuum seal after perforation.
It is available in the standard version, which is the one shown on this page,
but can be provided in other versions upon request.

Sp14
Vacuum gauge
item 09 05 16 Sp17

Punch
item 00 08 152

Vacuum cup
item 01 40 15s

VACUUM GAUGE
Scale Double Scale Admissable Temperature of Notes Case Weight
Item
mbar KPa scale error use material g
09 05 99 0 ÷ -1000 0 ÷ -100 1.6% -10 °C ÷ +50 °C in glycerine bath stainless steel 250

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
3.05
MINI PNEUMATIC VACUUM SWITCHES

These extremely compact vacuum switches give or remove a pneumatic

signal, depending on the model, when a certain adjustable level of
vacuum is reached.
The pressure differential existing between the set maximum value and
3D drawings are available on vuototecnica.net

that of the signal recovery at rest is not adjustable.

They are particularly suited for controlling vacuum generators and for
activating pneumatic valves.

Adjustment screw

Vacuum
connection

Item 12 01 30 12 02 30
Adjustment range mbar abs. 930 ÷ 50 900 ÷ 40
Fixed differential mbar 50 ÷ 80 150 ÷ 180
Repeatability mbar ±5 ±5
Signal at rest NC NO
Supply pressure bar 2÷8 2÷8
Pneumatic microvalve item 00 12 17 00 12 18
Max flow rate of the microvalve at 6 bar NI / s 1.2 1.2
Operating temperature °C -10 ÷ +60 -10 ÷ +60
Weight g 104 102

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.06
MINI ELECTROMECHANICAL VACUUM SWITCH

This extremely compact vacuum switch gives an electric signal when a

certain adjustable level of vacuum is reached.
The pressure differential existing between the set maximum value and the
value of reset of the rest signal is 50- 60 mbar and it is not adjustable.

3D drawings are available on vuototecnica.net

They are particularly suited when an electrical signal is needed when
a certain level of vacuum is reached, for safety, for starting a cycle, for
checking the cup grip, etc.

Adjustment screw

NBR rubber
protection

Vacuum
connection

Item 12 02 10
Adjustment range mbar abs. 930 - 10
Fixed differential mbar abs. from 50 to 60
Repeatability mbar ±1.5
Maximum overpressure bar 5
Microswitch item 00 12 12
Contacts one in commutation
Flow rate of contacts A 10.1 at 250 VAC
Electrical connections Type 110 fast-on terminals
Operating temperature °C -25 - +80
Protection IP 55
Weight g 102

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.07
MICRO DIGITAL VACUUM SWITCHES

If accurately calibrated and compensated for temperatures, these small

devices are able to give very precise digital signals to the set maximum
measuring value.
The switching point, which is within the scale value, can be easily
3D drawings are available on vuototecnica.net

programmed by means of an adjustment screw located on the upper part of

the device.

A red LED near the screw indicates the digital output signal commutation
status.
The pressure differential (hysteresis) between the set maximum value and
the value of reset of the rest signal is 2% of the set value and cannot be
adjusted.
They are composed of a polycarbonate enclosure, which includes the
sensor and the electric circuit, and of a coupler or a small aluminium
manifold with the vacuum connections.
Item 12 05 10 can also be rotated freely to place the display in the desired
position, without having to unscrew it from the vacuum connection. The
vacuum connection can be carried out via male or female M5 connectors,
while the electrical connection is made via a three-connector cable with
which they are equipped. Mini digital vacuum switches are suited for
controlling dry air and non-corrosive gasses. They are recommended in all
those cases that require a signal when a certain level of vacuum is reached,
for safety, for starting a cycle, for checking the cup grip, etc.

Item 12 05 10 *
Vacuum Seal
connection Hex. 8
3
Fitting (nickel-plated Body (polycarbonate)
brass)

Red LED
Three-pole shielded cable Ø 3.2 L=1500 mm
Adjustment screw

Item 12 05 11 *
Manifold (anodised aluminium)

Body (polycarbonate)

Red LED
Three-pole shielded cable Ø 3.2 L=1500 mm
Adjustment screw

Vacuum connection

* Complete the code indicating the electrical type of the output: P = PNP; N = NPN

Cable colour Delivery

brown positive pole
black output signal
blue negative pole

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
3.08
MICRO DIGITAL VACUUM SWITCHES

INTERNAL ELECTRICAL DIAGRAMS OUTPUT CONTACT DIAGRAM

3D drawings are available on vuototecnica.net

NPN open contact The LED lights up at the pre-set pressure and switches
off at the pre-set pressure minus the hysteresis

Indicator

Vacuum
Positive pole
Sensor
Main load

circuit
Output signal

Negative pole
Hysteresis

PNP open contact

Set value Atmospheric

pressure
Indicator

Vacuum 3
Sensor Positive pole
Main
circuit Output signal

load

Negative pole

Characteristics and Item 12 05 10 P Item 12 05 10 N

electrical specifications Item 12 05 11 P Item 12 05 11 N
Adjustment range from 0 to -1 bar
Maximum overpressure 2 bar
Operating voltage 10.8 - 30 VDC (Protection against polarity inversion)
Electrical absorption ≤20 mA
Commutation outputs 1 digital PNP, NO Maximum commutation current 80 mA 1 digital NPN, NO
Reaction time ≤1 ms
Commutation frequency 1000Hz
Hysteresis Not adjustable, 2% of the maximum set value
Repeatability ±2% of the measuring range
Commutation indicator Red LED
Insulation resistance 100 MΩ
Test voltage 500 VAC, 1 min
Degree of protection IP 40

Environmental operating conditions

Installation position Any
Controllable fluids Dry air and non-corrosive gas
Operating temperature -10 - +60 °C
Storage temperature -20 - +70 °C
Interference emission In compliance with EN 55011, Group 1, Class B
Resistance to interference In compliance with EN 61326 – 1

Characteristics and mechanical specifications

Container material Polycarbonate PC
Connection material Nickel-plated brass and aluminium
Weight (without cable) About 5g
Electrical connection Three-conductor cable, 1.5 m long
Connection to the fluid M5 male or female threading

3.09
ANALOGUE VACUUM SWITCH

These compact and extremely light switches come enclosed in a

sturdy ABS casing; these features allow their installation on the
machine and close to the application. If accurately calibrated, these
analogue switches provide very precise measurements values.
3D drawings are available on vuototecnica.net

The adjustment range is from 0 to -1 bar and can be interfaced

with external logics via an analogue output from 1 to 5 Volts and
a digital PNP output, configurable via Teach-In.
The switching point, as well as the hysteresis from 0 to 100% of
the set value, can be easily programmed via push buttons located
on the control panel; the two two-colour LEDs on the control panel
signal the commutation status and the error code, if any.
These devices can be rotated freely to place the display in the
desired position, without having to unscrew them from the vacuum
connection.
The vacuum connection is dual threaded: male G 1/8” or female M5.
The electrical connection is an M8 4-pin threaded plug and upon
request the connection cable is available in PUR, with an axial or
radial connector.
These vacuum switches are suited for measuring and controlling dry
air and non-corrosive gasses.
They are recommended in all those cases that require a measurement
and commutation to be installed on safety or energy-saving devices,
on systems for optimising the work cycle time and in circuit level of
vacuum adjustment circuits.

Electrical
connection

Vacuum
connection

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.10
ANALOGUE VACUUM SWITCH

WIRING DIAGRAM WALL FIXING KIT

3D drawings are available on vuototecnica.net

Item 00 12 22

2 M4x20 screws

Connections Cable colours

1. V+ Pin1 = brown
2. analogue output Pin2 = white
3. V- Pin3 = blue O-ring 2043
4. commutation output Pin4 = black

Characteristics and Item 12 07 10

3
electrical specifications Vacuum switch
Adjustment range from 0 to -1 bar
Maximum overpressure 5 bar
Operating voltage 10.8 - 30 VDC (Protection against polarity inversion)
Electrical absorption ≤30 mA
Commutation output 1 digital PNP, NO or NC programmable, maximum commutation current 250 mA
Analogue output 1 - 5 V; impedance load ≥500 Ω
Output tolerance ±1%
Offset 1 V - 0.1 Volt
Reaction time ≤2.5 ms
Commutation frequency 400Hz
Hysteresis Adjustable from 0 to 100% of the maximum set value
Repeatability ±0.2% of the measuring range
Error code signal Two-colour LED
Insulation resistance 100 MΩ to 500 VDC
Test voltage 1000 VAC, 1 min
Degree of protection IP 65

Environmental operating conditions

Installation position Any
Measurable fluids Non-corrosive gas and dry air
Operating temperature 0 - +50 °C
Storage temperature -20 - +80 °C
Interference emission In compliance with DIN EN 50081 - 1
Resistance to interference In compliance with DIN EN 50082 - 2

Characteristics and mechanical specifications

Container material ABS plastic - PC
Connection material Nickel-plated brass
Weight 19 g
Electrical connection With M8 - 4 pin coupler
Connection to the fluid Male G 1/8” or female M5 threading

Accessories
Electrical connection cable With axial connector, 5 m - PUR M8 x 1x 0.25 mm - Item 00 12 20
Electrical connection cable With radial connector, 5 m - PUR M8 x 1x 0.25 mm - Item 00 12 21
Wall fixing kit Support with o-ring and screws - Item 00 12 22

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.11
DIGITAL VACUUM AND PRESSURE SWITCHES

These compact and extremely light digital vacuum and pressure

switches are enclosed in a sturdy ABS casing.
These features allow installation on the machine and close to the
application.
3D drawings are available on vuototecnica.net

These digital switches are accurately calibrated and compensated

for temperatures and therefore are able to give very precise
measurements values. The detected values are shown on the display,
making it unnecessary to use a vacuum gauge. The two LEDs, one red
and one green, built-in the control panel, indicate the commutation
status of the two digital output signals.
The two commutation outputs are completely independent.
The switching points within the scale values, including hysteresis from
0 to 100% of the set value, are easily programmable via the buttons
located on the control panel.
Other additional functions can be configured, such as the comparison
between two values, NO and NC contacts, choice of the measurement
unit, locking the programmed values and functions, display reversal,
etc. These devices can be rotated freely to place the display in the
desired position, without having to unscrew them from the vacuum
connection.
The vacuum or the pressure connections can be carried out via a
dual male G 1/8” or female M5 threading. The electrical connection is
an M8 4-pin threaded plug and upon request the connection cable is
available in PUR, with an axial or radial connector. These switches are
suited for measuring and controlling dry air and non-corrosive gas.
They are recommended in all those cases that require a signal when a
certain level of vacuum is reached set for safety, for starting a cycle,
for checking the cup grip, etc. Moreover, the hysteresis function allows
3 managing the vacuum generator compressed air supply, allowing
considerable energy saving.

Electrical
connection

Vacuum and
compressed
air connection

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.12
DIGITAL VACUUM AND PRESSURE SWITCHES

WIRING DIAGRAM WALL FIXING KIT

3D drawings are available on vuototecnica.net

Item 00 12 22

2 M4x20 screws

Connections Cable colours

1. V+ Pin1 = brown
2. commutation output 2 Pin2 = white
3. V- Pin3 = blue
O-ring 2043
4. commutation output 1 Pin4 = black

Characteristics and Item 12 10 10 Item 12 25 11

electrical specifications Vacuum switch Pressure switch
3
Adjustment range from 0 to -1 bar from 0 to 10 bar
Maximum overpressure 5 bar 16 bar
Minimum detectable values 0.01 bar 0.01 bar
1 KPa --
1 mmHg --
0.1 InHg --
Operating voltage 10.8 - 30 VDC (Protection against polarity inversion)
Electrical absorption <15 mA / <3 mA energy saving mode
Commutation output 2 digital PNP, 2 digital NPN, NO or NC programmable, maximum commutation current 250 mA
Display tolerance ≤ ±2% F.S.
Reaction time ≤2.8 ms
Commutation frequency 200Hz
Hysteresis Adjustable from 0 to 100% of the maximum set value
Repeatability ±0.2% of the measuring range
Display 3-digit, 7-segment LED
Insulation resistance 100 MΩ to 500 VDC
Test voltage 1000 VAC, 1 min
Degree of protection IP 65

Environmental operating conditions

Characteristics and mechanical specifications

Container material ABS plastic - PC
Connection material Nickel-plated brass
Weight 20 g
Electrical connection With M8-4 pin coupler
Connection to the fluid Male G 1/8” or female M5 threading

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.13
DIGITAL VACUUM SWITCHES

Changes the shape of these digital vacuum switches with respect to

those previously described, from cylindrical to parallelepiped. However,
the container in which they are enclosed remains in ABS and is also
especially compact and extremely light to allow for its installation on
3D drawings are available on vuototecnica.net

board automatisms and near use. These carefully calibrated devices

are able to provide very accurate measurement values. The detected
values are shown on the display, making it unnecessary to use a vacuum
gauge. The panel includes two LED indicators, one green and one red,
which indicate the switching status of the two digital output signals.
The switching outputs are completely independent. The switching
points within the scale values, including hysteresis from 0 to 100% of
the set value, are easily programmable via the buttons located on the
control panel. Other additional functions can be configured, such as the
comparisons between values, NO and NC contacts, the choice of the
units of measure, the blocking of functions and programmed values, etc.
The vacuum connection can be made by means of a G 1/8” male or M5
female double threading connection.
Electrical connection for item 12 30 10 is push-in with a M8-4 pin
threaded jack. A connection cable can be provided in PUR upon request
with corresponding axial or radial connector.
Instead, item 12 30 10 A already has an integrated PUR, 2-metre long
connection cable. The adjustment range of vacuum switch 12 30 10 is
from 0 to -1 bar, with two digital PNP outputs that can be set by means
of Teach-in. The adjustment range of item 12 30 10 A, while it is also
between 0 and -1 bar, can instead be interfaced with external logics via a
1 to 5 volt analogue output and two digital PNP outputs.
This series of digital vacuum switches is suitable for measuring and
control of dry air and non-corrosive gases. These are recommended in
3 all cases where maximum and minimum value signalling is required,
set for safety reasons, in order to start a work cycle, to control vacuum
cup gripping, and so on. In addition, with the hysteresis function,
it is possible to manage the compressed air supply to the vacuum
generators, allowing for considerable energy savings.

Item 12 30 10

Vacuum M8 connection
connection - 4 pin

Item 12 30 10 A

Vacuum
connection

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.14
DIGITAL VACUUM SWITCHES

WIRING DIAGRAMS

3D drawings are available on vuototecnica.net

DC Brown DC Brown
MAIN COMMUTATION

MAIN COMMUTATION
Analogue OUT
orange

OUT 1 Black OUT 1 Black

OUT 2 White OUT 2 White

CIRCUIT

Load
Load
Load

Load
DC Blue DC Blue

Item 12 30 10 A Item 12 30 10

Characteristics and Item 12 30 10 A Item 12 30 10

electrical specifications Vacuum switch Vacuum switch
Adjustment range from 0 to -1 bar 3
Maximum overpressure 3 bar
Minimum detectable values 0.1 KPa
0.001 Kgf/cm2
0.001 bar
0.01 psi
0.1 InHg
1 mmHg
0.1 mmH2O
Operating voltage 12 - 24 VDC ±10% (Protection against polarity inversion)
Electrical absorption ≤60 mA
Digital output 2 PNP, maximum commutation current 100 mA
Analogue output 1 analogue, 1 + 5 V ±2% F.S. --
Display tolerance ≤ ±2% F.S. ±1 digit
Reaction time ≤2.5 ms
Hysteresis Adjustable
Repeatability ±0.2% ±1 digit of the measuring range
Display LED at 3 1/2 digit, 7 segments, OUT 1 green OUT 2 red
Insulation resistance 50 MΩ to 500 VDC
Test voltage 1000 VAC, 1 min
Degree of protection IP 40

Environmental operating conditions

Installation position Any
Measurable fluids Non-corrosive gas and dry air
Operating temperature 0 - +50 °C
Storage temperature -20 - +60 °C
Interference emission In compliance with EN 55011, Group 1, class B
Resistance to interference In compliance with EN 61326 – 1

Characteristics and mechanical specifications

Container material ABS plastic - PC
Connection material Nickel-plated brass
Weight 65 g, including electrical cable 35 g, including electrical cable
Electrical connection -- With M8-4 pin coupler
Electrical connection cable 5-wire 2m cable 4-wire 0.3 m cable
Connection to the fluid Male G 1/8” or female M5 threading

3.15
DIGITAL VACUUM AND PRESSURE SWITCHES

These compact and extremely light switches come enclosed in a

sturdy ABS casing; these features allow their installation on the
machine and close to the application.
These digital switches are accurately calibrated and compensated
3D drawings are available on vuototecnica.net

for temperatures and therefore are able to give very precise

measurements values. The detected values are shown on the display,
making it unnecessary to use a vacuum gauge. The two LEDs, one red
and one green, built-in the control panel, indicate the commutation
status of the two digital output signals.
The two commutation outputs are completely independent.
The switching points within the scale values, including hysteresis, are
easily programmable via the buttons located on the control panel.
Additional functions are also programmable, such as comparison
between two values, NO and NC contacts, choice of the unit of
measurement, programmed value and function blocking, etc.
The vacuum or the pressure connections can be carried out via a dual
connection with female G 1/8” thread, while the electrical connection
is carried out through the 4-conductor cable with which they are
equipped. These switches are suited for measuring and controlling
dry air and non-corrosive gas.
They are recommended in all those cases that require a signal when a
certain level of vacuum is reached set for safety, for starting a cycle,
for checking the cup grip, etc. Moreover, the hysteresis function allows
managing the vacuum generator compressed air supply, allowing
considerable energy saving.

Vacuum and Vacuum and

compressed compressed
air connection air connection

Threaded cap G1/8”

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.16
DIGITAL VACUUM AND PRESSURE SWITCHES

WIRING DIAGRAMS

3D drawings are available on vuototecnica.net

DC Brown DC Brown
MAIN COMMUTATION

MAIN COMMUTATION

Load

Load
OUT 1 Black OUT 1 Black

OUT 2 White OUT 2 White

CIRCUIT

Load

CIRCUIT
Load
DC Blue DC Blue

Characteristics and Item 12 20 10 P Item 12 35 10 P

electrical specifications Vacuum switch Pressure switch
Adjustment range from 0 to -1 bar from 0 to 10 bar
Maximum overpressure 5 bar 15 bar
Minimum detectable values 1 mbar 10 mbar
0.1 KPa 0.001 MPa 3
0.001 Kgf/cm2 0.01 Kgf/cm2
0.001 bar 0.01 bar
0.01 psi 0.1 psi
0.1 InHg --
1 mmHg --
10 mmH2O --
Operating voltage 12 - 24 VDC ±10% (Protection against polarity inversion)
Electrical absorption ≤55 mA
Commutation output 2 digital PNP, NO or NC, maximum commutation current 80 mA
Display tolerance ≤ ±2% F.S. ±1 digit
Reaction time ≤2.5 ms
Hysteresis Adjustable
Repeatability ±0.2% of the measuring range
Display LED at 3 1/2 digit, 7 segments, OUT 1 green OUT 2 red
Insulation resistance 50 MΩ to 500 VDC
Test voltage 1000 VAC, 1 min
Degree of protection IP 40

Environmental operating conditions

Characteristics and mechanical specifications

Container material ABS plastic - PC
Connection material Nickel-plated brass
Weight 105 g, including electrical cable
Electrical connection With 4-conductor wire cable length 2 m
Connection to the fluid Female G 1/8” threading

Accessories
Fixing kit wall - Item 00 12 30
table - Item 00 12 31
panel - Item 00 12 32
Note: Add the letter N after the item (for example 12 20 10 N) for NPN and non PNP commutation output.

3.17
DIGITAL VACUUM AND PRESSURE SWITCHES WITH TWO-COLOUR DISPLAY

These devices are also enclosed within a robust ABS container. They are carefully
calibrated and at compensated temperature, ensuring high-precision measurement
values. Detected values are viewed on the main two-colour (red and green) display and
programmable by the user to set different conditions. Setting values are easily viewable
3D drawings are available on vuototecnica.net

on a secondary display within the command panel. Two luminous indicators pertaining
to outlets 1 and 2 indicate the switching status of both digital and the analogue output
signals.
The switching outputs are completely independent.
The switching points within the scale values, including hysteresis, are easily
programmable via the buttons located on the control panel. Additional functions are also
programmable, such as comparison between two values, NO and NC contacts, choice of
measurement unit, programmed value and function blocking, etc. The connection to the
vacuum may be established by means of a male G 1/8" or female M5 double threading
connection. It is possible to establish an electric connection by means of a removable,
rapid installation data cable, supplied as standard.
Digital vacuum and pressure switches are suitable for measuring and controlling dry
air and non-corrosive gases. They are recommended in all those cases that require
a signal when a certain level of vacuum is reached set for safety, for starting a cycle,
for checking the cup grip, etc. Moreover, the hysteresis function allows managing the
vacuum generator compressed air supply, allowing considerable energy saving.

Sp12

Vacuum and
compressed
air connection

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.18
DIGITAL VACUUM AND PRESSURE SWITCHES WITH TWO-COLOUR DISPLAY

WIRING DIAGRAMS

3D drawings are available on vuototecnica.net

DC Brown

MAIN COMMUTATION
Analogue OUT
orange
OUT 1 Black

Load
OUT 2 White
CIRCUIT

Load
Load
DC Blue

Characteristics and Item 12 40 10 Art. 12 40 12 Item 12 40 20

electrical specifications Vacuum switch Vacuum switch Vacuum Switch - Pressure Switch
Adjustment range from 0 to -1 bar from 0 a -1 bar from -1 to 10 bar
Maximum overpressure 3 bar 3 bar 15 bar
Minimum detectable values 1 mbar 1 mbar 10 mbar
0.001 Kgf/cm2 0.001 Kgf/cm2 0.01 Kgf/cm2 3
0.001 bar 0.001 bar 0.01 bar
0.01 psi 0.01 psi 0.1 psi
0.1 inHg 0.1 inHg --
Operating voltage 12 - 24 VDC ±10% (Protection against polarity inversion)
Electrical absorption ≤40 mA
Digital output 2 PNP, maximum commutation current 125 mA
Analogue output 4 - 20 mA ±2.5% F.S. 1 ÷ 5 V ±2,5% F.S. 4 - 20 mA ±2.5% F.S.
Display tolerance ≤ ±2% F.S. ±1 digit
Reaction time ≤ 2.5 ms
Hysteresis Adjustable
Repeatability ±0.2% F.S. ±1 digit of the measuring range
Display 7 segments, main two-colour (red - green) display, secondary display (orange)
Insulation resistance 50 MΩ to 500 VDC
Test voltage 1000 VAC, 1 min
Degree of protection IP 40

Environmental operating conditions

Characteristics and mechanical specifications

Container material ABS plastic - PC
Connection material Nickel-plated brass
Weight 80 g, including electrical cable
Electrical connection 4-wire 2 m cable
Connection to the fluid Male G 1/8” or female M5 threading

Accessories
Fixing kit wall - Item 00 12 40
table - Item 00 12 41
panel - Item 00 12 42
panel + protection - Item 00 12 43

3.19
ACCESSORIES FOR ANALOGUE AND DIGITAL VACUUM AND PRESSURE SWITCHES
ITEM 12 20 10P and 12 35 10P
FIXING KIT
3D drawings are available on vuototecnica.net

Wall Item 00 12 30
2 M4x6 screws

Table Item 00 12 31
2 M4x6 screws

Panel Item 00 12 32

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
3.20
ACCESSORIES FOR ANALOGUE AND DIGITAL VACUUM AND PRESSURE SWITCHES
ITEM 12 40 10, 12 40 12 and 12 40 20
FIXING KIT
Wall Item 00 12 40
2 M3x0.5 screws

3D drawings are available on vuototecnica.net

Table Item 00 12 41
2 M3x0.5 screws

Panel Item 00 12 42

Panel plus protection Item 00 12 43

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
3.21
ACCESSORIES FOR ANALOGUE AND DIGITAL VACUUM AND PRESSURE SWITCHES

Cable with axial connector

3D drawings are available on vuototecnica.net

Item Description
Electrical connection cable with M8 - 4 pin axial connector
00 12 20 for digital vacuum and pressure switches
Cable length 5 m

Cable with radial connector

Item Description
Electrical connection cable with M8 - 4 pin radial connector
00 12 21 for digital vacuum and pressure switches
Cable length 5 m
3

Wall fixing kit

2 M4x20 screws

O-ring 2043

Item Description

00 12 22 Wall-fixing kit for digital vacuum and pressure switches

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.22
VACUUM ADJUSTMENT VALVES

When these valves reach a certain pre-calibrated vacuum degree, they

introduce atmospheric air into the circuit to prevent the increase of the set
value and to keep it constant.
They can be used as regulators only on circuits having only one vacuum

3D drawings are available on vuototecnica.net

pump and only one use (or more uses but all working at the same vacuum
degree).
In most cases, they are used as safety valves on non-commissioned
tanks or containers at high levels of vacuum and on vacuum cup
lifting systems.
The level of vacuum is adjusted by rotating the knurled
bush in both directions. The fine thread with which the
valve is provided ensures a very accurate calibration.
The temperature values within which the valves can
operate go from -20 °C to +120 °C.

Sp1

Sp1
Sp

Item 04 01 10 Item 04 02 10 Item 04 05 10

04 03 10
04 04 10

Vacuum adj. A B C D E F Sp Sp1 Material Max flow rate Weight

Item
mbar abs. Ø Ø Ø of the pump m3/h g
04 01 10 670 ÷ 1 45 8 G1/8” - - - 12 12 nickel-plated brass 4 30
04 01 10 INOX 670 ÷ 1 45 8 G1/8” - - - 12 12 stainless steel 4 30
04 02 10 670 ÷ 1 57 9 G1/2” 5 - 17 24 10 nickel-plated brass 20 78
04 02 10 INOX 670 ÷ 1 57 9 G1/2” 5 - 17 24 10 stainless steel 20 78
04 03 10 670 ÷ 1 60 11 G3/4” 5 - 23 30 17 nickel-plated brass 60 150
04 03 10 INOX 670 ÷ 1 60 11 G3/4” 5 - 23 30 17 stainless steel 60 150
04 04 10 670 ÷ 1 65 14.5 G1” 7 - 29 35 17 nickel-plated brass 100 212
04 04 10 INOX 670 ÷ 1 65 14.5 G1” 7 - 29 35 17 stainless steel 100 212
04 05 10 670 ÷ 1 104 22 G1” 1/2 15 55 42 50 20 nickel-plated brass 250 490
04 05 10 INOX 670 ÷ 1 104 22 G1” 1/2 15 55 42 50 20 stainless steel 250 490

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.23
VACUUM REGULATORS

These devices control the level of vacuum, maintaining it constant

at the pre-set value (secondary vacuum), regardless of the network's
flow rate and the fluctuations in vacuum level (primary vacuum).
They operate by membrane-piston and exploit the pressure
3D drawings are available on vuototecnica.net

differential between the secondary vacuum and the atmospheric

pressure.
Unlike the vacuum control valves, reducers do not release air into
the circuit, thereby allowing for the creation more grip points taken at
different degrees of vacuum, from a single vacuum source.
The level of vacuum is adjusted manually by turning the knurled
thumb screw clockwise to increase it, and counter clockwise to
decrease it.
Technical features
- Operation: membrane-piston regulator
- Adjustable operating pressure: from 800 to 1 mbar abs.
- Flow rate : from 2 to 160 m3/h.
- Room temperature: from -10 to +80 °C
- Installation position: any
Usage
The best use of vacuum reducers is in centralised plants where,
regardless of the plant's level of vacuum, each outlet can be adjusted
within that value. Moreover, they are necessary whenever the working
vacuum must be lower than the primary vacuum.

Adj. screw

Cap

Vacuum gauge

A Max capac. B C D F G H I L M O P Q Vacuum gauge Weight

Item
Ø m3/h Ø Ø Ø item Kg
11 01 10 G1/4” 6 47 42.0 10 40 60 20 6.5 89.0 40 G1/8” 30 40 09 03 15 0.60
11 02 10 G3/8” 10 47 42.0 10 40 60 20 6.5 89.0 40 G1/8” 30 40 09 03 15 0.58
11 03 10 G1/2” 20 53 52.0 15 55 85 25 8.5 105.0 50 G1/4” 36 63 09 03 10 1.15
11 04 10 G3/4” 40 55 55.5 15 70 100 30 8.5 110.5 50 G1/4” 36 63 09 03 10 1.39
11 05 10 G1” 80 60 58.0 15 90 120 30 8.5 118.0 60 G1/4” 36 63 09 03 10 2.08
11 06 10 G1” 1/2 160 54 77.5 15 130 160 20 8.5 131.5 99 G1/4” 36 63 09 03 10 5.49
Note: The vacuum gauges are not integral parts of the regulators and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.24
REGULATORS FOR ROUGH VACUUM LEVELS

The regulators on this page are based on the same operation

principle as the ones described in the previous page and have the
same function. The only difference is that in these ones the minimum
adjustable level of vacuum is close to the atmospheric pressure value.

3D drawings are available on vuototecnica.net

The level of vacuum is adjusted manually by turning the knurled
thumb screw clockwise to increase it, and counter clockwise to
decrease it.
Technical features
- Operation: membrane-piston regulator
- Adjustable operating pressure: from 980 to 1 mbar abs.
- Flow rate: from 20 to 160 m3/h
- Room temperature: from -10 to +80 °C
- Installation position: any
Usage
These regulators are used as the previously described ones, but they
offer the additional advantage of regulating even levels of vacuum
close to the atmospheric pressure.

3
Adj. screw

Cap

Vacuum gauge

A Max capac. B C D F G H I L M O P Q Vacuum gauge Weight

Item
Ø m3/h Ø Ø Ø item Kg
11 03 50 G1/2” 20 53 52.0 15 90 120 25 8.5 105.0 60 G1/4” 36 63 09 03 10 2.07
11 05 50 G1” 80 60 58.0 15 90 120 30 8.5 118.0 100 G1/4” 36 63 09 03 10 3.74
11 06 50 G1” 1/2 160 54 77.5 15 130 160 20 8.5 131.5 99 G1/4” 36 63 09 03 10 5.54
Note: The vacuum gauges are not integral parts of the regulators and, therefore, must be ordered separately

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.25
VACUUM REGULATORS WITH PNEUMATIC ADJUSTMENT

Vacuum regulators with pneumatic adjustment differ from the previous ones for the way they adjust the
level of vacuum; in fact, instead of acting manually on the adjustment screw, it is necessary to act on the
pneumatic cylinder compressed air supply: the higher the pressure, and the higher the level of vacuum
and vice-versa.
3D drawings are available on vuototecnica.net

Vacuum regulators are used to adjust the pre-set level of vacuum and keep it constant (secondary
vacuum), regardless of the pump vacuum level or the vacuum level (primary vacuum).
Unlike the vacuum adjusting valves, regulators do not introduce atmospheric air into the circuit,
thus producing more gripping points with different vacuum values, from only one vacuum
source.
Their operating principle is based on the contrasting action between a pneumatic
cylinder with short stroke and a fluctuating piston driven by the pressure differential
existing between the secondary vacuum and the atmospheric pressure.
Technical features
- Operation: membrane-piston regulator
- Supply pressure: from 0 to 3 bar for regulators item 11 .. 30;
from 0 to 5 bar for regulators item 11 .. 80.
- Adjustable working pressure: from 800 to 1 mbar abs. for regulators item 11 .. 30;
from 980 to 1 mbar abs. for regulators item 11 .. 80:
- Flow rate: from 2 to 160 m3/h.
- Room temperature: from -10 to +80 °C
- Installation position: any
Usage
Vacuum regulators are mainly used on centralised plants where, regardless of the plant level of vacuum, each
grip can be adjusted within that value. Moreover, they are necessary whenever the working vacuum must be
lower than the primary vacuum and kept constant. Vacuum regulators with pneumatic adjustment can be
installed away from the control point, since it is sufficient to have a pressure regulator on the control panel to
act on them.
3

Cap

Vacuum gauge

A Max capac. B C D E F G H I L M N O P Q R S T Vacuum gauge Weight

Item
Ø m3/h Ø Ø Ø Ø item Kg
11 01 30 G1/4” 6 47 42.0 10 20 10.5 60 20 6.5 89.0 40 G1/8” G1/8” 30 40 9.0 45 6.0 09 03 15 0.71
11 02 30 G3/8” 10 47 42.0 10 20 10.5 60 20 6.5 89.0 40 G1/8” G1/8” 30 40 9.0 45 6.0 09 03 15 0.69
11 03 30 G1/2” 20 53 52.0 15 26 16.5 85 25 8.5 105.0 50 G1/8” G1/4” 36 63 16.5 58 10.5 09 03 10 1.32
11 04 30 G3/4” 40 55 55.5 15 26 16.5 100 30 8.5 110.5 50 G1/8” G1/4” 36 63 24.0 58 18.0 09 03 10 1.94
11 05 30 G1” 80 60 58.0 15 26 16.5 120 30 8.5 118.0 60 G1/8” G1/4” 36 63 34.0 58 28.0 09 03 10 2.35
11 06 30 G1” 1/2 160 54 77.5 15 30 19.5 160 20 8.5 131.5 99 G1/4” G1/4” 36 63 37.5 80 42.5 09 03 10 5.56
11 03 80 G1/2” 20 53 52.0 15 26 16.5 120 25 8.5 105.0 60 G1/8” G1/4” 36 63 34.0 58 28.0 09 03 10 2.28
11 05 80 G1” 80 60 58.0 15 26 16.5 120 30 8.5 118.0 100 G1/8” G1/4” 36 63 34.0 58 28.0 09 03 10 3.96
11 06 80 G1” 1/2 160 54 77.5 15 30 19.5 160 20 8.5 131.5 99 G1/4” G1/4” 36 63 37.5 80 42.5 09 03 10 5.60
Note: The vacuum gauges are not integral parts of the regulators and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
3.26
DIAGRAMS REFERRING TO THE LEVEL OF VACUUM ACCORDING TO THE SERVO-
CONTROL SUPPLY PRESSURE

100

3D drawings are available on vuototecnica.net

100
80

90
70

80
60 11 01 30
11 02 30
70 11 03 30
-Kpa

50
11 04 30
11 05 30
60 11 01
06 30
40
11 02 30
11 03 30
-Kpa

50
30 11 04 30
11 05 30
40 11 06 30
20

30
10

20
0
3
0 0,25 0,5 0,75 1 1,25 1,5 1,75 2 2,25 2,5 2,75
10
bar

0
100
0 0,25 0,5 0,75 1 1,25 1,5 1,75 2 2,25 2,5 2,75
90 bar

100
80

90
70

80
60

70 11 03 80
-Kpa

50 11 05 80
11 06 80
60
40
11 03 80
-Kpa

50 11 05 80
30
11 06 80
40
20

30
10

20
0
0 0,25 0,5 0,75 1 1,25 1,5 1,75 2 2,25 2,5 2,75 3 3,25 3,5 3,75 4 4,25 4,5
10
bar

0
0 0,25 0,5 0,75 1 1,25 1,5 1,75 2 2,25 2,5 2,75 3 3,25 3,5 3,75 4 4,25 4,5
bar

Note: The values shown in the tables are purely indicative as they depend on atmospheric pressure, the flow rate of the vacuum source and the quality of the compressed air supply

3.27
SEALING KIT FOR VACUUM REDUCERS
3D drawings are available on vuototecnica.net

Vacuum regulator
Item
item
00 11 113 11 01 10
00 11 114 11 02 10
00 11 115 11 03 10
00 11 116 11 04 10
00 11 117 11 05 10
00 11 118 11 06 10
00 11 119 11 03 50
00 11 120 11 04 50
00 11 121 11 05 50
00 11 122 11 01 30
00 11 123 11 02 30
00 11 124 11 03 30
00 11 125 11 04 30
00 11 126 11 05 30
00 11 127 11 06 30
00 11 128 11 03 80
00 11 129 11 05 80
00 11 130 11 06 80

3.28
VACUUM VALVES AND SOLENOID
VALVES

SUCTION VALVES FOR VACUUM PRESS BAGS PG. 4.01

SUCTION VALVES FOR RESIN INFUSION MOULDS PG. 4.02

3D drawings are available on vuototecnica.net

PLUNGER VALVES PG. 4.03
MECHANICALLY OPERATED VALVES PG. 4.04
VALVES WITH BALL SHUTTER PG. 4.05
SHUT-OFF VALVES PG. 4.06 ÷ 4.07
CHECK VALVES PG. 4.08
MEMBRANE CHECK VALVES PG. 4.09
MANUAL 2-WAY MINIATURE VACUUM VALVES PG. 4.09
MANUAL 2-WAY VACUUM VALVES PG. 4.10
MANUAL 3-WAY VACUUM VALVES PG. 4.11
SERVO-CONTROLLED 3-WAY VACUUM VALVES PG. 4.12 ÷ 4.16
3-WAY VACUUM SOLENOID PILOT VALVES PG. 4.17 ÷ 4.18
2-WAY VACUUM SOLENOID PILOT VALVES PG. 4.19 ÷ 4.20
DIRECT DRIVE 2-WAY VACUUM SOLENOID VALVES PG. 4.21
DIRECT DRIVE 2-WAY VACUUM SOLENOID VALVES PAG. 4.21-1 ÷ 4.24-1
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES PG. 4.22 ÷ 4.27
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES WITH 2 ELECTRIC COILS PG. 4.28 ÷ 4.33
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES PG. 4.34 ÷ 4.36
SOLENOID VALVE ACCESSORIES AND SPARE PARTS:
- ELECTRIC COILS PG. 4.37 ÷ 4.38
- ELECTRIC COIL CONNECTORS PG. 4.39 ÷ 4.40
- VALVE AND SOLENOID VALVE PILOT SEALING AND MEMBRANE KIT PG. 4.41
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES WITH LOW ABSORPTION ELECTRIC COIL PG. 4.42 ÷ 4.47
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE SOLENOID PILOT VALVE
AND WITH LOW ABSORPTION ELECTRIC COIL PG. 4.48 ÷ 4.53
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES WITH LOW ABSORPTION ELECTRIC COIL PG. 4.54 ÷ 4.55
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE SOLENOID PILOT VALVE
AND WITH LOW ABSORPTION ELECTRIC COIL PG. 4.56 ÷ 4.57
SOLENOID VALVES - SPECIAL PRODUCTS UPON REQUEST
MULTI-FUNCTION MODULES WITH BUILT-IN VACUUM SOLENOID VALVES PG. 4.58 ÷ 4.59 4
SOLENOID VALVE ACCESSORIES AND SPARE PARTS WITH LOW ABSORPTION ELECTRIC COIL:
- SOLENOID PILOT VALVES WITH BUILT-IN LOW ABSORPTION ELECTRIC COIL PG. 4.60
- BISTABLE IMPULSE SOLENOID PILOT VALVES AND WITH BUILT-IN ELECTRIC COIL PG. 4.60
- SOLENOID PILOT VALVES WITH INTERFACE VALVE PG. 4.61
- SOLENOID PILOT VALVE ELECTRIC COIL CONNECTORS PG. 4.61
- SOLENOID VALVE SEALING KIT WITH LOW ABSORPTION ELECTRIC COILS PG. 4.62
- SOLENOID VALVE PILOT MEMBRANE WITH LOW ABSORPTION ELECTRIC COILS PG. 4.62
4
3D drawings are available on vuototecnica.net
SUCTION VALVES FOR VACUUM PRESS BAGS

The suction valves described on this page have been

designed for a quick vacuum connection on press
bags for composite fibre products.
These valves are composed of a steel distributor,

3D drawings are available on vuototecnica.net

to be inserted inside the bag, equipped with a cam
housing suitable for the quick coupler for the vacuum
connection. The latter is made with reeded and
anodised aluminium and is easily coupled with the
distributor by simply rotating it on its axis by 90°, once
it has been inserted.
A silicone seal, to be placed between the two elements
and the press bag, guarantees a perfect vacuum seal.
Manual two-way valves, quick couplers or simply
flexible pipe fittings can be assembled onto these
valves.
They are currently available in the two versions
indicated in the table, but can be provided in different
sizes and shapes upon request for a minimum
amount.
Maximum temperature of use: 220°

Quick coupling
fitting

Two-way Fitting
manual valve for TPR hose 4

Coupler

Sealing gasket
Distributor

Maximum Hole to Two-way Quick Fitting

flow rate be made manual coupler for TPR
Item
recommended in bag valve fitting hose Weight A B C D E F G Sp
m3/h Ø item item item g Ø Ø Ø
VSS 3/8” 10 16 13 02 11 RR3/8” RTPR3/8” 178 60 32 10 13 9 24 G3/8” 19
VSS 1/2” 20 19 13 03 11 RR1/2” RTPR1/2” 218 65 35 10 13 12 30 G1/2” 25
Note: The two-way valves and fittings are not integral parts of the suction valves and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.01
SUCTION VALVES FOR RESIN INFUSION MOULDS

Once laid on the resin infusion mould connections, these suction

valves allow a quick vacuum connection and guarantee a perfect seal.
They are made with silicone rubber, while their support is made with
anodised aluminium. Manual two-way valves, quick couplers or
3D drawings are available on vuototecnica.net

simply flexible pipe fittings can be assembled onto these valves.

They are available in the two versions shown below, but can be
supplied in different sizes and shapes upon request.

SEALING SUCTION PUMP

VACUUM CUP FOR
VACUUM

RESIN SUCTIONED VACUUM BAG

RESIN FROM VACUUM

MOULD

Quick coupling
fitting

4
Two-way Fitting
manual valve for TPR hose

Maximum Two-way Quick Fitting Weight G

flow rate manual coupler for TPR
Item
recommended valve fitting hose
m3/h item item item g Ø
08 85 15 1/2” S 20 13 03 11 RR1/2” RTPR1/2” 108 G1/2”
08 85 15 3/4” S 40 13 03 11 RR3/4” RTPR3/4” 103 G3/4”
Note: The two-way valves and fittings are not integral parts of the suction valves and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.02
PLUNGER VALVES

Plunger valves are composed of a natural colour or chrome-plated cylindrical brass

body, depending on the items, of a steel plunger with a conical valve, a thrust spring, a
nylon disc whose task is to thrust the spring onto a larger contact surface, thus avoiding
unsightly prints on the load to be gripped.

3D drawings are available on vuototecnica.net

Connected to vacuum, they are normally closed.
They activate suction, thus creating a vacuum, only when the plunger is in contact with
the gripping surface.
They are also available in various versions, all suitable for our vacuum cups.

Sp22

Nylon disc

A B C D E Weight Vacuum cup

Item
Ø Ø g item
19 01 10 53 9 15.0 G1/4” G1/4” 160 08 150 16
19 01 11 53 9 16.0 M12 G1/4” 166 08 80 20 4
19 01 12 53 9 22.0 M12 G1/4” 152 08 127 15

Sp22

Nylon disc

A B C D E Weight Vacuum cup

Item
Ø Ø g item
19 02 10 61.5 12 22.0 G3/8” G3/8” 164 08 150 15
08 200 10
08 250 10
19 03 10 61.0 10 22.5 G1/2” G3/8” 172 08 300 10
08 350 10
19 04 10 68.5 11 42.0 G1/2” G3/8” 182 08 360 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.03
MECHANICALLY OPERATED VALVES

These valves are composed of an anodised

aluminium body, a steel pin solidly connected to a
conical shutter and of a thrust spring.
Connected to vacuum, they are normally closed.
3D drawings are available on vuototecnica.net

They activate suction, thus creating a vacuum, only

when the pin is activated by the cams or any other
mechanical device.
They can be used as an alternative to plunger
valves when these cannot be assembled onto the
vacuum cups.

Sp30

Ring nut KM4

A B C D E F G H I Weight
Item
Ø Ø Ø Ø g
19 02 30 112 80 23 35 9 G3/8” 63 8 M20 x 1 252

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.04
VALVES WITH BALL SHUTTER

Valves with ball shutters activate suction, creating vacuum in the cups on which they are
applied, only when the load to be held activates the sealing shutter.
They are made of an anodised aluminium body, a nylon ball shutter, a calibrated thrust
spring and a threaded brass closing plug.

3D drawings are available on vuototecnica.net

When properly calibrated, they guarantee a perfect vacuum seal.
They are recommended for making vacuum operated clamping surfaces.
They can be supplied in different sizes and shapes upon request and for a minimum
quantity to be defined in the order.

CONSTRUCTION OF SEAT FOR VALVE INSERTION

A B C D D1 Actuating force Weight

Item
Ø Ø Kg g
22 01 10 30 6 24 40 M30 x 1.5 2.30 70

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
4.05
SHUT-OFF VALVES

These are special one-way valves that, when properly calibrated, allow a certain
quantity of fluid to go through; afterwards, if the fluid continues to go through,
they automatically close.
These shut-off valves have been specially designed to be applied on the cups
3D drawings are available on vuototecnica.net

and, in case of lack of objects to be gripped, of defective grips or leaks, they

automatically deactivate suction, thus preventing any reduction of the level of
vacuum on the other gripping cups.
They are provided calibrated and commissioned, ready to be installed. They are
made with anodised aluminium and can be supplied in different shapes and
sizes upon request and for a minimum quantity to be defined in the order.

Hex. 13

A B C D D1 E Weight
Item
Ø Ø g
14 01 05 32 26 6 G1/8” G1/8” 8 8
Minimum trigger flow = 1.5 m3/h Minimum level of vacuum = -250 mbar

Hex. 20

A B C D D1 E Weight
Item
Ø Ø g
14 01 10 45 30 15 G1/4” G3/8” 14 28
Minimum trigger flow = 4 m /h3
Minimum level of vacuum = -250 mbar

Hex. 20

A B C D D1 E Weight
Item
Ø Ø g
14 01 15 45 30 15 G1/4” G1/4” 14 29
Minimum trigger flow = 4 m3/h Minimum level of vacuum = -250 mbar

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.06
SHUT-OFF VALVES

3D drawings are available on vuototecnica.net

Hex. 20

A D D1 E Weight
Item
Ø Ø g
14 02 10 59 G1/4” G1/4” 14 42
Minimum trigger flow = 4 m /h3
Minimum level of vacuum = -250 mbar

Hex. 20

A B C D D1 E Weight
Item
Ø Ø g
14 03 10 59 47 12 G3/8” G1/4” 14 36
Minimum trigger flow = 4 m /h3
Minimum level of vacuum = -250 mbar

Hex. 20

A B C D D1 E Weight
Item
Ø Ø g
14 05 10 59 47 12 G3/8” G1/4” 14 34
4
Minimum trigger flow = 4 m /h3
Minimum level of vacuum = -250 mbar

A B C D D1 E Weight
Item
Ø Ø g
Sp.22
14 06 10 50 38 12 G3/8” G3/8” 14 38
Minimum trigger flow = 4 m3/h Minimum level of vacuum = -250 mbar

SHUT-OFF VALVES WITH CONTROLLED LOSS

These are based on the same operating principle as the previously described shut-off valves. They differ only
in the sealing shutter which, even when completely closed, allows the vacuum source a minimum of suction.
This feature helps pick up the vacuum cup that has not gripped the object, for example, due to early activation
of the suction, to recreate the vacuum inside it and then to grip without having to repeat the work cycle. If,
on the other hand, the vacuum cup does not grip because there is no object to be gripped, the valve does not
prevent the lowering of the level of vacuum on the remaining vacuum cups, but the small size of the loss is
easily controllable and therefore, recoverable.
Fully made with anodised aluminium.

Loss Minimum A B C D D1 E F Weight Hex. F

Item max trigger flow
Nl/min m3/h Ø Ø g
14 01 11 7.5 1 36.0 29.5 6.5 G1/8” G1/8” 10 13 8
14 02 11 7.5 1 37.5 29.5 8.0 G1/4” G1/4” 15 17 16
14 03 11 24.0 3 42.0 32.5 9.5 G3/8” G3/8” 17 22 28
Minimum level of vacuum = -250 mbar

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.07
CHECK VALVES

These one-way valves are made with bronze and brass with a seal in
NBR nitrile rubber or, upon request, in Viton®, only for series 10 ... 11.
To ensure a practical assembly they are available in two versions:
horizontal and vertical.
3D drawings are available on vuototecnica.net

Fitted on the vacuum pump suction inlet, as soon as the latter

stop, these valves prevent the air from returning in the plant
(piping, tanks, autoclaves, vacuum gripping systems, vacuum
cups, etc.), guaranteeing a perfect seal and preventing the
oil from returning into the pump stator, which would cause
considerable damages.
Therefore, check valves are mandatory on all vacuum pumps
with lubrication that do not have them built-in.

HORIZONTAL
Sp
R Sp H L Weight
Item
Ø Kg
10 02 10 G3/8” 27 49 43 0.19
10 03 10 G1/2” 27 49 43 0.17
10 04 10 G3/4” 34 58 52 0.27
10 05 10 G1” 42 66 62 0.43
4 10 06 10 G1” 1/4 50 75 72 0.59
10 07 10 G1” 1/2 57 86 80 0.79
10 08 10 G2” 69 99 94 1.08

VERTICAL
R Sp D H Weight
Item
Ø Ø Kg
10 01 11 G1/4” 21 28 47 0.10
10 02 11 G3/8” 25 35 59 0.17
10 03 11 G1/2” 26 35 58 0.12
10 04 11 G3/4” 33 42 65 0.28
10 05 11 G1” 40 48 74 0.42
10 06 11 G1” 1/4 50 61 82 0.64
10 07 11 G1” 1/2 55 71 92 0.87
10 08 11 G2” 70 87 100 2.70
Note: To order valves with seals in Viton®, add the letter V to the item (example: 10 02 11 V)

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.08
MEMBRANE CHECK VALVES

These valves have the same features of the

previously described check valves, but they are
made with anodised aluminium, which makes them
particularly light.

3D drawings are available on vuototecnica.net

The seal is guaranteed by an EPDM membrane
instead of the metal shutter with NBR seal.
Thanks to these features and their modern design,
they are recommended for pneumatic vacuum
generators and, of course, on vacuum pumps.

R Sp D H Weight
Item
Ø Ø g
10 01 15 G1/4” 20 30 42 46
10 02 15 G3/8” 24 35 50 74
10 03 15 G1/2” 24 37 55 86
10 04 15 G3/4” 33 42 64 110
10 05 15 G1” 40 49 74 162

4
MANUAL 2-WAY MINIATURE VACUUM VALVES

These small manual valves are suited for

intercepting vacuum on vacuum cup holders and
any small utilities on which solenoid valves cannot
be installed.
They feature a hexagonal nickel-plated brass body,
a chrome-plated brass ball shutter and a seal in
plastic material to guarantee a perfect seal.
A lever on the ball shutter, manually rotated 90°,
allows for valve opening or closing with no effort.

D Mouth Sp E F H Weight
Item
Ø Ø g
13 01 11 G1/4” 8 21 7 32 39 80
13 02 11 G3/8” 8 21 10 30 40 74
13 03 11 G1/2” 10 25 12 33 45 110

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.09
MANUAL 2-WAY AND 3-WAY VACUUM VALVES

These manual valves are used for intercepting vacuum in all those
plants where solenoid valves cannot be installed.
They feature a die-cast nickel-plated brass body, a chromed brass
ball shutter and Teflon® seals to guarantee perfect seal even at high
3D drawings are available on vuototecnica.net

temperatures.
A lever on the ball shutter, manually rotated 90°, allows opening or
closing the valve precisely and with no effort.

Hex. G

2-WAY MANUAL VALVES

A B C D Mouth E F G L Weight
Item
Ø Ø Kg
13 01 10 49 23 48 G1/4” 10 24 25 18 80 0.13
13 02 10 52 23 56 G3/8” 10 23 29 20 80 0.13
13 03 10 61 30 63 G1/2” 15 30 31 25 88 0.21
13 04 10 68 36 72 G3/4” 20 33 35 31 114 0.32
13 05 10 85 44 80 G1” 25 42 43 38 113 0.47
13 06 10 99 57 105 G1” 1/4 32 50 49 47 137 0.74
13 07 10 109 70 126 G1” 1/2 40 55 54 54 156 1.26
13 08 10 130 83 135 G2” 50 62 68 66 156 1.77
13 09 10 168 140 210 G3” 75 84 84 99 246 7.09

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.10
MANUAL 3-WAY VACUUM VALVES

3D drawings are available on vuototecnica.net

Hex. G

3-WAY MANUAL VALVES

A B C D Mouth E G L Weight
Item
Ø Ø Kg
13 01 15 77 37.5 87 G1/4” 10 17.5 22 109 0.16
13 02 15 81 39.5 94 G3/8” 10 19.5 22 109 0.19
13 03 15 81 39.5 94 G1/2” 15 19.5 29 109 0.30
13 04 15 76 39.0 81 G3/4” 20 19.0 32 130 0.49
13 05 15 90 45.0 91 G1” 25 24.0 41 130 0.85
13 06 15 118 56.0 134 G1” 1/4 32 32.0 50 170 1.76
13 07 15 114 62.0 138 G1” 1/2 40 39.0 55 150 2.45

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.11
SERVO-CONTROLLED 3-WAY VACUUM VALVES

These two-position, three-way valves feature pneumatically activated

conical shutters.
They can be used normally either closed or open.
They are recommended in all the cases that require a quick exchange
3D drawings are available on vuototecnica.net

between the vacuum pump suction and the air inlet into the circuit for
a quick restoration of the atmospheric pressure.
They are composed of an anodised aluminium body, two Vulkollan®
shutters assembled onto a stainless steel stem, a membrane for
servo-control made with special compounds and a thrust spring for
the shutter return.
These valves allow reducing frictions and internal dynamic stresses to
the minimum. The result being a high response speed and a guarantee
of long lasting duration.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Servo-control pressure: see table
Temperature of suctioned fluid: from -5 to +60°C

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 01 31 G1/4” 6 1000 0.5 5 10 8.5 56.8 4÷7 0,32
07 02 31 G3/8” 10 1000 0.5 5 10 11.5 103.8 4÷7 0,31
Note: Valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.12
SERVO-CONTROLLED 3-WAY VACUUM VALVES

3D drawings are available on vuototecnica.net

X = Compressed air supply X = Compressed air supply
P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

4
A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-en. Ø mm2 *bar Kg
07 03 31 G1/2” 20 1000 0.5 6 15 15.0 176 6÷8 0.490
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: Valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 04 31 G3/4” 40 1000 0.5 7 16 20 314 6÷8 1.060
07 05 31 G1” 90 1000 0.5 7 16 25 490 6÷8 0.964
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: Valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.13
SERVO-CONTROLLED 3-WAY VACUUM VALVES
3D drawings are available on vuototecnica.net

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.14
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES, FOR LARGE FLOW RATES

Strengthened by our constant desire for research and innovation and

our experience, acquired over more than forty years of operations in
the vacuum sector, we have made these new valves using absolutely
innovative technologies, to guarantee exceptionally low intervention

3D drawings are available on vuototecnica.net

times, almost negligible pressure drops, and minimal dimensions
compared to the large connections with which they are equipped.
Furthermore, we have obtained them from aluminium block to
eliminate even the slightest chance of loss due to transpiration, as
perhaps could occur with a fusion.
This new series of solenoid valves for vacuums are three-way, two-
position and are composed of:
- An anodised aluminium body set with attachment connections
- Two conical Vulkollan® shutters fitted on the aluminium pistons,
pneumatically powered with spring return
The composition of these valves, especially the original Teflon® slide
system that the pistons have been equipped with, help minimise
friction and internal dynamic stress, deriving high response speed and
ensuring enduring operation.
They can be used normally either closed or open.
The three-way valves are used for vacuum interception on power
supply units and suction palletisers, vacuum thermoformers, vacuum
packaging units, robots, feeders, bag opening units and in all those
cases where rapid exchange between pump suction for vacuums
and air supply into the circuit is necessary for quick restoration of
atmospheric pressure.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Servo-control pressure: from 4 to 8 bar
Temperature of suctioned fluid: from – 5 to + 60°C

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 08 31 G2” 390 1000 0.5 110 70 52 2123 4÷8 5.5
Note: Valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.15
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES, FOR LARGE FLOW RATES
3D drawings are available on vuototecnica.net

X = Compressed air supply X = Compressed air supply

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of B C D E F G Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Kg
DDN 14 G1/2” 20 1000 0.5 30 15 14 154 127 35 110 30 63 75 0.83
DDN 25 G1” 90 1000 0.5 55 33 25 490 142 50 128 43 82 90 1.56
Note: The coil and the connector are not integral parts of the solenoid pilot valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.21
DIRECT DRIVE 2-WAY VACUUM SOLENOID VALVES

These direct drive two-way, two-position vacuum solenoid valves in the new series feature
a conical shutter servo-controlled by the vacuum.
They are normally closed, but they can be supplied normally open upon request.
They are composed of an anodised aluminium body where the connections are located,
3D drawings are available on vuototecnica.net

a conical silicon shutter assembled onto a stainless steel stem and a membrane in
a special rubberised and coated compound. An actuator activated by an electric coil
manages the vacuum at the servo-control. The operating principle of these solenoid
valves is based on the pressure differential between the vacuum pump or generator and
the pressure of the suctioned air. By addressing this “differential pressure” to the servo-
control via the actuator, the shutter can be controlled without compressed air or springs.
Due to their operating principle, they are not recommended on plants with rough vacuum
levels (below 850 absolute mbar, equal to 15% vacuum).
The lack of springs, frictions and internal dynamic stresses favours a high response
speed and guarantees long lasting operation of the solenoid valve.
The standard electric coil is fully plasticised with synthetic resin, tight execution,
insulation class F (up to 155°C) compliant with VDE standards, with 6.3 mm three-
terminal electrical connections in compliance with EN 175301-803 (ex-DIN 43650).
Protection degree IP 54, IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ± 10%.
Maximum absorption: 20 V.A. with AC and 18 W with DC.
The electric coil can be rotated 360°. The connector can be rotated 180° on the coil
and can be supplied, upon request, with LED light, anti-interference circuit and/or with
protection devices against overvoltage and polarity reversal.
This series of solenoid valves can be used on vacuum systems without compressed air
and in all applications where suction has to be controlled separately from the air inlet into
circuit, such as degasifiers, autoclaves, vacuum thermo-welders, etc. The solenoid valve
must be always chosen according to the flow rate and, therefore, to the vacuum pump or
generator suction connection.
Technical features
Operating pressure: from 0.5 to 850 absolute mbar
Temperature of suctioned fluid: from – 5 to + 60°C

4
Connector

Electric coil

A = Use
P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
EGN 40 NC G1” 1/2 230 850 0.5 75 50 40 1256 M8 4.07
70 60
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.02
4.21-1
DIRECT DRIVE 2-WAY VACUUM SOLENOID VALVES

3D drawings are available on vuototecnica.net

Electric coil
4

Connector

A = Use
P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
EGN 40 NO G1” 1/2 230 850 0.5 75 50 40 1256 M8 4.07
70 60
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.22-1
4.03
DIRECT DRIVE 2-WAY VACUUM SOLENOID VALVES
3D drawings are available on vuototecnica.net

Connector
4
Electric coil

A = Use
P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
EGN 52 NC G2” 390 850 0.5 75 50 52 2123 M8 6.70
70 60
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.04
4.23-1
DIRECT DRIVE 2-WAY VACUUM SOLENOID VALVES

3D drawings are available on vuototecnica.net

Electric coil 4
Connector

A = Use
P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
EGN 52 NO G2” 390 850 0.5 75 50 52 2123 M8 6.70
70 60
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.24-1
4.05
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES

The three-way vacuum solenoid valves in this series are two-position valves with
pneumatically servo-controlled conical shutters.
They can be used normally either closed or open.
They are composed of an anodised aluminium body, two Vulkollan® shutters assembled
3D drawings are available on vuototecnica.net

onto a stainless steel stem, a membrane for servo-control made with special compounds
and a thrust spring for the shutter return; an actuator activated by an electric coil
managed the compressed air supply.
These valves allow reducing frictions and internal dynamic stresses to the minimum.
The result being a high response speed and a guarantee of long lasting duration.
The standard electric coil is fully plasticised with synthetic resin, tight execution,
insulation class F (up to 155°C) compliant with VDE standards, with 6.3 mm three-
terminal electrical connections in compliance with EN 175301-803 (ex DIN 43650).
Protection degree IP 54; IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum absorption: 20 V.A. with AC and 18 W with DC.
The electric coil can be rotated 360°. The connector can be rotated 180° on the coil
and can be supplied, upon request, with LED lights, anti-interference circuit and/or with
protection devices against overvoltage and polarity reversal.
The three-way vacuum solenoid valves are used for vacuum interception on power supply
units and suction palletisers, robots, feeders, bag opening units and in all those cases
where rapid exchange between pump suction for vacuums and air supply into the circuit
is necessary for quick restoration of atmospheric pressure.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Servo-control pressure: see table
Temperature of suctioned fluid: from -5 to +60°C

Electric coil Connector

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 01 11 G1/4” 6 1000 0.5 16 27 8.5 56.8 4÷7 0.56
07 02 11 G3/8” 10 1000 0.5 16 27 11.5 103.8 4÷7 0.54
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.22
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES

3D drawings are available on vuototecnica.net

Electric coil Connector
4

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 03 11 G1/2” 20 1000 0.5 16 40 15.0 176 6÷8 0.73
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.23
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
3D drawings are available on vuototecnica.net

Electric coil Connector

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 04 11 G3/4” 40 1000 0.5 16 40 20 314 6÷8 1.25
07 05 11 G1” 90 1000 0.5 18 42 25 490 6÷8 1.16
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.24
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES

3D drawings are available on vuototecnica.net

Connector

Electric coil

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 06 11 G1” 1/2 230 1000 0.5 60 38 40 1256 6÷8 4.79
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.25
3-WAY VACUUM SOLENOID VALVES, PILOT-OPERATED FOR LARGE CAPACITIES

Strengthened by our constant desire for research and innovation and our experience, acquired over more
than forty years of operations in the vacuum sector, we have made these new solenoid valves using
absolutely innovative technologies, to guarantee exceptionally low intervention times, almost negligible
pressure drops, and minimal dimensions compared to the large connections with which they are equipped.
3D drawings are available on vuototecnica.net

Furthermore, we have obtained them from aluminium block to eliminate even the slightest chance of loss
due to transpiration, as perhaps could occur with a fusion.
This new series of solenoid valves for vacuums are three-way, two-position and are composed of:
- An anodised aluminium body set with attachment connections
- Two conical Vulkollan® shutters fitted on the aluminium pistons, pneumatically powered with spring
return
- An actuator, powered by an electrical coil to manage compressed air supply
The composition of these valves, especially the original Teflon® slide system that the pistons have been
equipped with, help minimise friction and internal dynamic stress, deriving high response speed and
ensuring enduring operation.
They can be used normally either closed or open.
The standard electric coil of the actuator is fully plastic-coated in synthetic resin, watertight,
insulation class F (up to 155°C) as per standard VDE, with 6.3 mm three-terminal electrical
connections for connectors in compliance with EN 175301-803.
Degree of protection IP 54;
IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ± 10%.
Maximum absorption: 20 VA in AC and 18 W in DC.
The electric coil can be rotated 360°. The connector can be rotated 180° on the coil and can be
supplied, upon request, with LED lights, anti-interference circuit and/or with protection devices against
overvoltage and polarity reversal.
The three-way solenoid valves are used for vacuum interception on power supply units and suction
palletisers, vacuum thermoformers, vacuum packaging units, robots, feeders, bag opening units and in all
those cases where rapid exchange between pump suction for vacuums and air supply into the circuit is
necessary for quick restoration of atmospheric pressure.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Servo-control pressure: from 4 to 8 bar
4 Temperature of suctioned fluid: from – 5 to + 60°C
Connector

Electric coil

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 08 11 G2” 390 1000 0.5 78 50 52 2123 4÷8 5.87
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.26
3-WAY VACUUM SOLENOID VALVES, PILOT-OPERATED FOR LARGE CAPACITIES

3D drawings are available on vuototecnica.net

Connector

Electric coil
4

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 09 11 G3” 750 1000 0.5 132 84 80 5024 4÷8 11.8
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.27
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH TWO ELECTRIC COILS
These solenoid valves have the same function and the same structure as the
previously described three-way valves.
Even their structure is the same, but their distinctive features are the two coils
that with a simple electric impulse exchange the shutter positions and keep
3D drawings are available on vuototecnica.net

them in this position till the next impulse even in absence of compressed air at
the servo control and of electric current.
This is the reason why their use is especially recommended in all those cases
requiring maximum connection security at the vacuum source, even in the
absence of electrical and pneumatic power supply.
The standard electric coils are fully plastic-coated in synthetic resin, watertight,
insulation class F (up to 155°C) as per standard VDE, with 6.3 mm three-terminal
electrical connections for connectors in compliance with EN 175301-803
(ex DIN 43650). Protection degree IP 54; IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum absorption: 8 - 20 V.A. with AC and 6.5 - 18 W with DC.
The electric coils can be rotated 180°. The connectors can be rotated 180° on
the coils and can be supplied, upon request, with LED lights, anti-interference
circuit and/or with protection devices against overvoltage and polarity reversal.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Servo-control pressure: see table
Temperature of suctioned fluid: from -5 to +60°C

Electric coil Connector

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 01 51 G1/4” 6 1000 0.5 16 27 8.5 56.8 4÷7 0.59
07 02 51 G3/8” 10 1000 0.5 16 27 11.5 103.8 4÷7 0.58
Note: The coils and the connectors are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.28
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH TWO ELECTRIC COILS

3D drawings are available on vuototecnica.net

Electric coil Connector

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 03 51 G1/2” 20 1000 0.5 16 40 15.0 176 6÷8 0.97
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: The coils and the connectors are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.29
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH TWO ELECTRIC COILS
3D drawings are available on vuototecnica.net

Electric coil Connector

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 04 51 G3/4” 40 1000 0.5 16 40 20 314 6÷8 1.51
07 05 51 G1” 90 1000 0.5 18 42 25 490 6÷8 1.41
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: The coils and the connectors are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.30
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH TWO ELECTRIC COILS

3D drawings are available on vuototecnica.net

Connector

Electric coil

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 06 51 G1” 1/2 230 1000 0.5 60 38 40 1256 6÷8 5.24
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: The coils and the connectors are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.31
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH TWO ELECTRIC COILS, FOR LARGE CAPACITIES
The innovative construction technology of these solenoid valves and
their conformation are the same as those previously described. What
differentiates them are the two simple electrical impulse coils that
exchange the shutter positions and keep them in position until the
3D drawings are available on vuototecnica.net

next impulse even in absence of compressed air at the servo control

and of electric current. This is the reason why their use is especially
recommended in all those cases requiring maximum connection
security at the vacuum source, even in the absence of electrical and
pneumatic power supply.
The standard electric coils of the actuator are fully plastic-coated
in synthetic resin, watertight, insulation class F (up to 155°C) as per
standard VDE, with 6.3 mm three-terminal electrical connections for
connectors in compliance with EN 175301-803. Degree of protection
IP 54;
IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum absorption: 20 VA in AC and 18 W in DC.
The electric coils can be rotated 180°, as well as the connectors,
which can be supplied upon request with LED lights, with an anti-
interference circuit and/or with protection devices against overvoltage
and polarity reversal.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Servo-control pressure: from 4 to 8 bar
Temperature of suctioned fluid: from – 5 to + 60°C

Connector

4
Electric coil

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 08 51 G2” 390 1000 0.5 78 50 52 2123 4÷8 6.0
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.32
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH TWO ELECTRIC COILS, FOR LARGE CAPACITIES

3D drawings are available on vuototecnica.net

Connector

Electric coil

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 09 51 G3” 750 1000 0.5 132 84 80 5024 4÷8 11.8
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.33
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES

These direct drive three-way, two-position vacuum solenoid valves feature conical shutters
servo-controlled by the vacuum.
They are normally closed as standard, but they can be supplied normally open upon request.
They are composed of an anodised aluminium body where the connections are located, two
3D drawings are available on vuototecnica.net

silicone shutters assembled onto a stainless steel stem and a membrane in special reinforced
compound. An actuator activated by an electric coil manages the vacuum at the servo-control.
The operating principle of these solenoid valves is based on the pressure differential between
the vacuum pump or generator and the pressure of the suctioned air.
By addressing this “differential pressure” to the servo-control via the actuator, the shutters can
be controlled without compressed air or springs.
Due to their operating principle, they are not recommended on plants with rough vacuum
levels (below 850 absolute mbar, equal to 15 % vacuum).
The lack of springs, frictions and internal dynamic stresses favours a high response speed and
guarantees long lasting operation.
The standard electric coil is fully plasticised with synthetic resin, tight execution, insulation
class F (up to 155°C) compliant with VDE standards, with 6.3 mm three-terminal electrical
connections in compliance with EN 175301-803 (ex DIN 43650). Protection degree IP 54; IP 65
with connector inserted.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum absorption: 20 V.A. with AC and 18 W with DC.
The electric coil can be rotated 360°. The connector can be rotated 180° on the coil and can be
supplied, upon request, with LED lights, anti-interference circuit and/or with protection devices
against overvoltage and polarity reversal.
The solenoid valves in this series, along with the uses described for the 07 .. 11 series, can be
used on plants with no compressed air.
The solenoid valve must be always chosen according to the flow rate and, therefore, to the
vacuum pump or generator suction connection.
Technical features
Operating pressure: from 0.5 to 850 absolute mbar
Temperature of suctioned fluid: from -5 to +60°C

4
Connector Electric coil

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 03 40 NC G1/2” 20 850 0.5 30 15 15 176 6.5 1.53
07 03 40 NO 20 18
07 04 40 NC G3/4” 40 850 0.5 30 15 20 314 6.5 1.50
07 04 40 NO 20 18
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.34
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES

3D drawings are available on vuototecnica.net

Connector Electric coil
4

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 05 40 NC G1” 90 850 0.5 38 18 25 490 6.5 1.91
07 05 40 NO 25 20
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.35
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES
3D drawings are available on vuototecnica.net

Connector Electric coil

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 06 40 NC G1” 1/2 230 850 0.5 75 50 40 1256 10.5 5.90
07 06 40 NO 70 60
Note: The coil and the connector are not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.36
SOLENOID VALVE ACCESSORIES AND SPARE PARTS

Electric coils
Electric coils are windings of copper wire on nylon coils fully
plasticised in synthetic resin which activate the electromagnetic
actuators with which the solenoid valves are provided. Crossed by an

3D drawings are available on vuototecnica.net

electric current, these coils generate a magnetic field which activates
the mobile core inside the actuators; the mobile core features a built-
in or fixed shutter which cause the valve commutation by opening and
closing their mouths.
The standard electric coils are fully plasticised with synthetic resin,
tight execution, insulation class F (up to 155°C) compliant with
VDE standards, with 6.3 mm 3-terminal electrical connections in
compliance with EN 175301-803 (ex DIN 43650).
Protection degree: IP 54; IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ±10%.
Tolerance permitted on the frequency value: ±5%
Room temperature: from -10 to +45°C
Fluid temperature: from -10 to +95°C
Electric absorption: 8 - 20 V.A. with AC and 6.5 - 18 W with DC.
The electric coils can be rotated 360°.

DIRECT AND ALTERNATING CURRENT COILS

Service Absorption Rated voltage Weight For solenoid valves
Item
ED g item
00 07 172 100% 6,5 W V24 DC 54 07 01 51 - 07 02 51
00 07 173 100% 8 V.A. V24 / 50 - 60Hz 54 07 01 51 - 07 02 51

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
4.37
SOLENOID VALVE ACCESSORIES AND SPARE PARTS
3D drawings are available on vuototecnica.net

DIRECT AND ALTERNATING CURRENT COILS

Service Absorption Rated voltage Weight
Item
ED g
00 07 03 N 100% 18 W V12 DC 100
00 07 04 N 100% 18 W V24 DC 100
00 07 06 N 100% 18 W V110 DC 100
For solenoid valves item
07 01 11 - 07 02 11 - 07 03 11 - 07 04 11 - 07 05 11 - 07 06 11 - 07 08 11 - 07 09 11
07 01 16 - 07 02 16 - 07 03 16
07 01 20 - 07 02 20 - 07 03 20
07 03 40 - 07 04 40 - 07 05 40 - 07 06 40
07 03 51 - 07 04 51 - 07 05 51 - 07 06 51 - 07 08 51 - 07 09 51
DDN 14

00 07 256 N 100% 20 V.A. V24/50 - 60 Hz 100

00 07 258 N 100% 20 V.A. V110/50 - 60 Hz 100
00 07 259 N 100% 20 V.A. V230/50 - 60 Hz 100
For solenoid valves item
07 01 11 - 07 02 11 - 07 03 11 - 07 04 11 - 07 05 11 - 07 06 11 - 07 08 11 - 07 09 11
07 01 16 - 07 02 16 - 07 03 16
07 01 20 - 07 02 20 - 07 03 20
07 03 40 - 07 04 40 - 07 05 40 - 07 06 40
07 03 51 - 07 04 51 - 07 05 51 - 07 06 51 - 07 08 51 - 07 09 51
DDN 14 - DDN 25

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
4.38
SOLENOID VALVE ACCESSORIES AND SPARE PARTS

Connectors are fundamental for bringing electric current to the solenoid

valve coils.
They are available in the simple plug version installed as standard and, upon
request, with LEDs to signal the presence of voltage, with anti-interference

3D drawings are available on vuototecnica.net

circuits, protection devices against overvoltage and polarity reversal.
When correctly installed, all connectors provide full protection against water
jets, according to EN 60529 standards (protection class IP 65).
Moreover, they meet VDE 0110-1/89 standards, working voltage up to 250
V, overvoltage category II, Degree of use 3, regarding insulation class.
In all contacts, a snap joint between contact holders and the external
protection guarantees a safe locking and easy assembly.
Safe locking is essential for guaranteeing the operator full protection when
handling the connector. The contact holder can be easily extracted from its
casing simply using a screwdriver. This operation also allows orienting the
earthing contact in the desired direction.

CONNECTORS FOR COILS

Nominal flow rate Max cross-section Temperature Ø cable Weight Notes For coils
Item of contacts of conductors in operation
A mm2 °C mm g item
00 07 174 max 16 1.5 -40 ÷ +90 6÷8 24 Standard 00 07 172
00 07 260 max 16 1.5 -40 ÷ +90 6÷8 24 With LED 00 07 173

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
4.39
SOLENOID VALVE ACCESSORIES AND SPARE PARTS
3D drawings are available on vuototecnica.net

CONNECTORS FOR COILS

Nominal flow rate Voltage Max cross-section Temperature Ø cable Weight Notes
Item of contacts of conductors in operation
A mm2 °C mm g

00 07 63 max 16 all 1.5 -40 ÷ +90 6÷8 24 Standard

00 07 101 max 16 V24DC - 24V/50 - 60Hz 1.5 -40 ÷ +90 6÷8 24 With white LED
00 07 186 max 16 V24DC - 24V/50 - 60Hz 1.5 -40 ÷ +90 6÷8 24 With red LED and filter
00 07 221 max 16 V24DC - 24V/50 - 60Hz 1.5 -40 ÷ +90 6÷8 24 With red LED
00 07 222 max 16 V230DC - 230V/50 - 60Hz 1.5 -40 ÷ +90 6÷8 24 With white LED
00 07 223 max 16 V230DC - 230V/50 - 60Hz 1.5 -40 ÷ +90 6÷8 24 With red LED and filter
For coils item
00 07 03 N - 00 07 04 N - 00 07 06 N
00 07 256 N - 00 07 258 N - 00 07 259 N

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
4.40
VACUUM VALVE AND SOLENOID VALVE SEALING KIT

Sealing kits are composed of a membrane, shutters and standard O-rings installed on our compressed air
and vacuum three-way valves and solenoid valves.
In the presence of very hot fluids (up to 250°C) or corrosive fluids, we can supply sealing kits in special
compounds. Please contact our technical department.

3D drawings are available on vuototecnica.net

Complete kit for valves: 07 01 31 e 07 02 31 item 00 07 267
07 03 31 item 00 07 268
07 03 31 LP item 00 07 287
07 04 31 e 07 05 31 item 00 07 269
07 04 31 LP e 07 05 31 LP item 00 07 288
07 06 31 item 00 07 270
07 06 31 LP item 00 07 289
07 08 31 item 00 07 380
07 09 31 item 00 07 384

Complete kit for solenoid valves: 07 01 11 e 07 02 11 item 00 07 271

07 03 11 item 00 07 272
07 03 11 LP item 00 07 290
07 04 11 e 07 05 11 item 00 07 273
07 04 11 LP e 07 05 11 LP item 00 07 291
07 06 11 item 00 07 274
07 06 11 LP item 00 07 292
07 08 11 item 00 07 372
07 09 11 item 00 07 382

Complete kit for solenoid valves: 07 01 51 e 07 02 51 item 00 07 275

07 03 51 item 00 07 276
07 03 51 LP item 00 07 293
07 04 51 e 07 05 51 item 00 07 277
07 04 51 LP e 07 05 51 LP item 00 07 294
07 06 51 item 00 07 278
07 06 51 LP item 00 07 295 4
07 08 51 item 00 07 381
07 09 51 item 00 07 385

Complete kit for solenoid valves: 07 03 40 e 07 04 40 item 00 07 279

07 05 40 item 00 07 280
07 06 40 item 00 07 281

PILOT MEMBRANES FOR VACUUM VALVES

AND SOLENOID VALVES

For valves Connections Material Colour Dimensions mm

Item
item
00 07 104 07 03 40 - 07 04 40 G1/2” - G3/4” Fabric NBR Black Ø 65
00 07 105 07 05 40 G1” Fabric NBR Black Ø 76
00 07 177 07 06 40 G1” 1/2 Fabric NBR Black Ø 110
00 07 229 07 01 11 - 07 01 31 - 07 01 51 G1/4” - G3/8” Vulkollan® Beige 49 x 35
07 02 11 - 07 02 31 - 07 02 51
00 07 230 07 03 11 - 07 03 31 - 07 03 51 G1/2” Urepan® 65 Grey - orange 62 x 39
00 07 296 07 03 11 LP - 07 03 31 LP - 07 03 51 LP G1/2” Vulkollan® Beige 62 x 39
00 07 231 07 04 11 - 07 04 31 - 07 04 51 G3/4” - G1” Urepan® 65 Grey - orange 79 x 49
07 05 11 - 07 05 31 - 07 05 51
00 07 297 07 04 11 LP - 07 04 31 LP - 07 04 51 LP G3/4” - G1” Vulkollan® Beige 79 x 49
07 05 11 LP - 07 05 31 LP - 07 05 51 LP
00 07 232 07 06 11 - 07 06 31 - 07 06 51 G1”1/2 Urepan® 65 Grey - orange 129 x 89
00 07 298 07 06 11 LP - 07 06 31 LP - 07 06 51 LP G1”1/2 Vulkollan® Beige 129 x 89

4.41
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH LOW ABSORPTION ELECTRIC COIL
The three-way vacuum solenoid valves in this series are two-position valves with
pneumatically servo-controlled conical shutters.
They can be used normally either closed or open.
They are composed of an anodised aluminium body, two Vulkollan® shutters
3D drawings are available on vuototecnica.net

assembled onto a stainless steel stem, a membrane for servo-control made with special
compounds and a thrust spring for the shutter return; a solenoid pilot valve activated by
a built-in electric coil managed the compressed air supply.
These valves allow reducing frictions and internal dynamic stresses to the minimum.
The result being a high response speed and a guarantee of long lasting duration.
The electric coils of the solenoid pilot valve are fully plastic-coated in synthetic resin,
watertight, insulation class F (up to 155°C) as per standard VDE, with 3 mm two-terminal
electrical connections for connectors in compliance with EN 175301-803
(ex DIN 43650) - C. Protection degree IP 54; IP 65 with connector inserted.
Available for voltages 12-24V/50-60Hz and 12-24VDC.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum electric power: 2 W
The connector can be rotated 180° on the coil and can be supplied, upon request, with
LED lights, anti-interference circuit and/or with protection devices against overvoltage
and polarity reversal.
A push-button device, built-in the solenoid pilot valve, allows manually opening and
closing the solenoid valve.
The 3-way vacuum solenoid valves are used for vacuum interception on power supply
units and suction palletisers, robots, feeders, bag opening units and in all those cases
where rapid exchange between pump suction for vacuums and air supply into the circuit
is necessary for quick restoration of atmospheric pressure.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Servo-control pressure: see table
Temperature of suctioned fluid: from -5 to +60°C

Connector

Manual drive Solenoid pilot

valve

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 01 13 G1/4” 6 1000 0.5 16 27 8.5 56.8 4÷7 0.44
07 02 13 G3/8” 10 1000 0.5 16 27 11.5 103.8 4÷7 0.43
Note: Specify the voltage of the electric coil when ordering. (Example: 07 01 13 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.42
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH LOW ABSORPTION ELECTRIC COIL

3D drawings are available on vuototecnica.net

Connector

Manual drive Solenoid pilot

valve

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 03 13 G1/2” 20 1000 0.5 16 40 15.0 176 6÷7 0.52
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: Specify the voltage of the electric coil when ordering. (Example: 07 03 13 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.43
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH LOW ABSORPTION ELECTRIC COIL
3D drawings are available on vuototecnica.net

Connector

Manual drive Solenoid pilot

valve
4

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 04 13 G3/4” 40 1000 0.5 16 40 20 314 6÷7 1.00
07 05 13 G1” 90 1000 0.5 18 42 25 490 6÷7 0.94
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: Specify the voltage of the electric coil when ordering. (Example: 07 04 13 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.44
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES
WITH LOW ABSORPTION ELECTRIC COIL

3D drawings are available on vuototecnica.net

Connector

Manual drive Solenoid pilot valve

Interface
Quick
discharge
valve 4

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 06 13 G1”1/2 230 1000 0.5 60 38 40 1256 6÷8 4.50
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: Specify the voltage of the electric coil when ordering. (Example: 07 06 13 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.45
3-WAY VACUUM SOLENOID VALVES, PILOT-OPERATED FOR LARGE CAPACITIES WITH
LOW ABSORPTION ELECTRIC COIL
The growing demand by automatic machine manufacturers in the packaging sector and the lack of high-speed three-way
vacuum solenoid valves on the market for capacities above 200 m3/h have led us to design and implement this new series of
solenoid valves that are able to meet these needs.
Strengthened by our constant desire for research and innovation and our experience, acquired over more than forty years
3D drawings are available on vuototecnica.net

of operations in the vacuum sector, we have made these new solenoid valves using absolutely innovative technologies, to
guarantee exceptionally low intervention times, almost negligible pressure drops, and minimal dimensions compared to the
large connections and minimum electrical absorption for their powering with which they are equipped.
Furthermore, we have obtained them from aluminium block to eliminate even the slightest chance of loss due to
transpiration, as perhaps could occur with a fusion.
This new series of solenoid valves for vacuums are three-way, two-position and are composed of:
- An anodised aluminium body set with attachment connections
- Two conical Vulkollan® shutters fitted on the aluminium pistons, pneumatically powered with spring return
- A solenoid pilot valve powered by a low absorption fitted electrical coil which managed compressed air supply
The composition of these valves, especially the original Teflon® slide system that the pistons have been equipped
with, help minimise friction and internal dynamic stress, deriving high response speed and ensuring enduring
operation.
They can be used normally either closed or open.
The electric coils of the solenoid pilot valve are fully plastic-coated in synthetic resin, watertight, insulation class F (up
to 155°C) as per standard VDE, with 3 mm two-terminal electrical connections for connectors in compliance with EN
175301-803. Degree of protection IP 54;
IP 65 with connector inserted.
Available for voltages 12-24V/50-60Hz and 12-24VDC.
Tolerance permitted on the nominal voltage value: ± 10%.
Maximum electric power: 2 W
The connector can be rotated 180° on the coil and can be supplied, upon request, with LED lights, anti-interference
circuit and/or with protection devices against overvoltage and polarity reversal.
A push-button device, built-in the solenoid pilot valve, allows manually opening and closing the solenoid valve.
The three-way solenoid valves are used for vacuum interception on power supply units and suction palletisers, vacuum
thermoformers, vacuum packaging units, robots, feeders, bag opening units and in all those cases where rapid exchange
between pump suction for vacuums and air supply into the circuit is necessary for quick restoration of atmospheric
pressure.
Technical features
4 Working pressure: from 0.5 to 1000 absolute mbar
Servo-control pressure: from 4 to 8 bar
Suctioned fluid temperature: from – 5 to + 60°C
Connector

Solenoid pilot valve

Manual drive
Interface
Quick
valve
discharge

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 08 13 G2” 390 1000 0.5 78 50 52 2123 4÷8 5.87
Note: Specify the voltage of the electric coil when ordering. (Example: 07 08 13 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.46
3-WAY VACUUM SOLENOID VALVES, PILOT-OPERATED FOR LARGE CAPACITIES WITH
LOW ABSORPTION ELECTRIC COIL

3D drawings are available on vuototecnica.net

Connector
4
Manual drive Solenoid pilot valve
Quick Interface
discharge valve

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 09 13 G3” 750 1000 0.5 132 84 80 5024 4÷8 11.80
Note: Specify the voltage of the electric coil when ordering. (Example: 07 09 13 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.47
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE
SOLENOID PILOT VALVE AND WITH LOW ABSORPTION ELECTRIC COIL
These solenoid valves have the same function and the same structure as the
previously described three-way valves.
Even their structure is the same; what differentiates them are the bistable
impulse solenoid pilot valve powered by a low absorption fitted electrical coil
3D drawings are available on vuototecnica.net

which, with a simple electrical impulse, exchanges the shutter positions and
keeps them there even in absence of electricity, until it receives a new impulse of
opposite polarity. For this reason, they can only be supplied with direct current
electric coils.
Their use is especially recommended in all those cases requiring maximum
connection security at the vacuum source, even in the absence of electrical
power supply.
The electric coils of the solenoid pilot valve are fully plastic-coated in synthetic
resin, watertight, insulation class F (up to 155°C) as per standard VDE, with 3
mm two-terminal electrical connections for connectors in compliance with EN
175301-803
(ex DIN 43650) - C. Protection degree IP 54; IP 65 with connector inserted.
Available for voltages 12-24VDC.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum electric power: 1 W
The connector can be rotated 180° on the coil and can be supplied, upon
request, with LED lights, anti-interference circuit and/or with protection devices
against overvoltage and polarity reversal.
The push-button device for their manual activation cannot be installed on these
solenoid valves.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Servo-control pressure: see table
Temperature of suctioned fluid: from -5 to +60°C

Connector

4
Solenoid pilot valve

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 01 53 G1/4” 6 1000 0.5 16 27 8.5 56.8 4÷7 0.44
07 02 53 G3/8” 10 1000 0.5 16 27 11.5 103.8 4÷7 0.43
Note: Specify the voltage of the electric coil when ordering. (Example: 07 01 53 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.48
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE
SOLENOID PILOT VALVE AND WITH LOW ABSORPTION ELECTRIC COIL

3D drawings are available on vuototecnica.net

Connector

Solenoid pilot
valve
4

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 *bar Kg
07 03 53 G1/2” 20 1000 0.5 16 40 15.0 176 6÷7 0.52
* Add the letters LP to the item for servo-controlled pressures 4 - 6 bar.
Note: Specify the voltage of the electric coil when ordering. (Example: 07 03 53 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.49
SERVO-CONTROLLED 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE
SOLENOID PILOT VALVE AND WITH LOW ABSORPTION ELECTRIC COIL
3D drawings are available on vuototecnica.net

Connector

Quick Interface
discharge valve

X = Compressed air supply X = Compressed air supply

P = Pump P = Discharge
A = Use A = Use
R = Discharge R = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of Pressure at Weight
Item abs. mbar msec passage servo-controlled
Ø m3/h min max energ. de-energ. Ø mm2 bar Kg
07 09 53 G3” 750 1000 0.5 132 84 80 5024 4÷8 11.80
Note: Specify the voltage of the electric coil when ordering. (Example: 07 09 53 V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).
Solenoid valve servo-controlled power must be supplied with non-lubricated compressed air, 5 micron filtration, according to standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.53
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES
WITH LOW ABSORPTION ELECTRIC COIL
These direct drive three-way, two-position vacuum solenoid valves feature conical
shutters servo-controlled by the vacuum.
They are normally closed as standard, but they can be supplied normally open upon
request.
3D drawings are available on vuototecnica.net

They are composed of an anodised aluminium body where the connections are located,
two silicone shutters assembled onto a stainless steel stem and a membrane in
special reinforced compound. A solenoid pilot valve activated by a built-in electric coil
manages the vacuum at the servo-control. The operating principle of these solenoid
valves is based on the pressure differential between the vacuum pump or generator
and the pressure of the suctioned air. By addressing this “differential pressure” to the
servo-control via the solenoid pilot valve, the shutters can be controlled without
compressed air or springs.
Due to their operating principle stated above, they are not recommended on plants
with rough vacuum levels (below 850 absolute mbar, equal to 15 % vacuum).
The lack of springs, frictions and internal dynamic stresses favours a high response
speed and guarantees long lasting operation.
The electric coils of the solenoid pilot valve are fully plastic-coated in synthetic resin,
watertight, insulation class F (up to 155°C) as per standard VDE, with 3 mm two-
terminal electrical connections for connectors in compliance with EN 175301-803 (ex
DIN 43650) - C.
Protection degree IP 54; IP 65 with connector inserted.
Available for voltages 12-24V/50-60Hz and 12-24VDC.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum electric power: 2 W
The connector can be rotated 180° on the coil and can be supplied, upon request, with
LED lights, anti-interference circuit and/or with protection devices against overvoltage
and polarity reversal. A push-button device, built-in the solenoid pilot valve, allows
manually opening and closing the solenoid valve.
The solenoid valves in this series, along with the uses described for the 07 .. 11 series,
can be used on plants with no compressed air.
The solenoid valve must be always chosen according to the flow rate and, therefore, to
the vacuum pump or generator suction connection.
4 Technical features
Operating pressure: from 0.5 to 850 absolute mbar
Temperature of suctioned fluid: from -5 to +60°C

Connector
Manual drive

Solenoid pilot
valve

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 03 43 NC G1/2” 20 850 0.5 33 17 15 176 6.5 1.35
07 03 43 NO 22 20
07 04 43 NC G3/4” 40 850 0.5 33 17 20 314 6.5 1.30
07 04 43 NO 22 20
Note: Specify the voltage of the electric coil when ordering. (Example: 07 03 43 NC V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.54
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES
WITH LOW ABSORPTION ELECTRIC COIL

3D drawings are available on vuototecnica.net

Connector
Manual drive

Solenoid pilot
valve
4

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 05 43 NC G1” 90 850 0.5 42 20 25 490 6.5 1.65
07 05 43 NO 28 22
Note: Specify the voltage of the electric coil when ordering. (Example: 07 05 43 NC V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.55
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE SOLENOID
PILOT VALVE AND WITH LOW ABSORPTION ELECTRIC COIL
These solenoid valves have the same function and the same structure as the
previously described three-way valves.
Even their structure is the same; what differentiates them are the bistable
impulse pilot valve powered by a low absorption fitted electrical coil which, with
3D drawings are available on vuototecnica.net

a simple electrical impulse, exchanges the shutter positions and keeps them
there even in absence of electricity, until it receives a new impulse of opposite
polarity. For this reason, they can only be supplied with direct current electric
coils.
Their use is especially recommended in all those cases requiring maximum
connection security at the vacuum source, even in the absence of electrical
power supply.
The electric coils of the solenoid pilot valve are fully plastic-coated in synthetic
resin, watertight, insulation class F (up to 155°C) as per standard VDE, with 3
mm two-terminal electrical connections for connectors in compliance with EN
175301-803
(ex DIN 43650) - C. Protection degree IP 54; IP 65 with connector inserted.
Available for voltages 12-24VDC.
Tolerance permitted on the nominal voltage value: ±10%.
Maximum electric power: 1 W
The connector can be rotated 180° on the coil and can be supplied, upon
request, with LED lights, anti-interference circuit and/or with protection devices
against overvoltage and polarity reversal.
The push-button device for their manual activation cannot be installed on these
solenoid valves.
Technical features
Operating pressure: from 0.5 to 850 absolute mbar
Temperature of suctioned fluid: from -5 to +60°C

Connector

4
Solenoid pilot
valve

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 03 63 NC G1/2” 20 850 0.5 33 17 15 176 6.5 1.35
07 03 63 NO 22 20
07 04 63 NC G3/4” 40 850 0.5 33 17 20 314 6.5 1.30
07 04 63 NO 22 20
Note: Specify the voltage of the electric coil when ordering. (Example: 07 03 63 NC V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.56
DIRECT DRIVE 3-WAY VACUUM SOLENOID VALVES WITH BISTABLE IMPULSE SOLENOID
PILOT VALVE AND WITH LOW ABSORPTION ELECTRIC COIL

3D drawings are available on vuototecnica.net

Connector

4
Solenoid pilot
valve

R = Pump R = Discharge
A = Use A = Use
P = Discharge P = Pump

A Max flow rate Level of vacuum Reaction time Mouth Cross-section of F Weight
Item abs. mbar msec passage
Ø m3/h min max energ. de-energ. Ø mm2 Ø Kg
07 05 63 NC G1” 90 850 0.5 42 20 25 490 6.5 1.65
07 05 63 NO 28 22
Note: Specify the voltage of the electric coil when ordering. (Example: 07 05 63 NC V24-CC)
The connector is not integral parts of the solenoid valve and, therefore, must be ordered separately (See accessories for solenoid valves).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.57
SOLENOID VALVES - SPECIAL PRODUCTS UPON REQUEST
MULTI-FUNCTION MODULES WITH BUILT-IN VACUUM SOLENOID VALVES
The needs of technical designers in the packaging sector and in the automation sector in general to have
more vacuum combined with different functions in the smallest possible space has led us to design and
implement this new series of multi-function modules.
Each module has two internal solenoid valves built inside it. Their ducts house the seats for the flow
3D drawings are available on vuototecnica.net

control valves, which can be operated externally by means of special knobs. Various connections made
at different points allow for connection of the module to instruments for reading and checking the level of
vacuum, such as vacuum gauges, vacuum switches, transducers, etc.
There are three modules currently available:
- Module A: The basic module with two integrated 1”1/2 and 1” solenoid valves, two flow regulators and
several additional connections.
- Module B: With two integrated 1/2 "and 1" solenoid valves and two flow regulators. Can be combined with
modules A and C.
- Module C: Module with two integrated 1/2” solenoid valves, a flow regulator and an additional connection.
Can be combined with module A or B.
The combination of modules A, B and C, feasible using special stainless steel tie-rods, allows for the
application of various functions from a single source of vacuum, as well as allowing for the elimination of
numerous pipes and fittings, often causing leaks. The multi-function modules are supplied already tested
to a guaranteed final level of vacuum of 0.5 mbar and perfectly sealed.
The technical characteristics are those of the pneumatically actuated three-way vacuum solenoid valves:
- Servo-control pressure: 6-7 bar; 4-6 bar for version LP, with non-lubricated compressed air, 5 micron
filtration, according to standard ISO 8573-1 class 4
- Operating pressure: from 0.5 to 3000 absolute mbar
- Electric coils: fully plastic-coated in synthetic resin, watertight, insulation class F (up to 155°C) as per
standard VDE, with 3 mm two-terminal electrical connections for connectors in compliance with EN
175301-803
- Protection degree IP 54; IP 65 with connector inserted.
- Tolerance permitted on the nominal voltage value: ± 10%
- Electrical power of the coils: from 1 to 2 W, depending on the electrical voltage
- Temperature of suctioned fluid: from – 5 to + 60°C
The ideal use of these multi-function modules is on vacuum thermoformers and vacuum thermo-welders,
but they are also widely used on packaging and filling machines in the packaging sector and in all those
cases where it is necessary to manage the vacuum at different points and times. Upon request, the
4 modules can be customised and implemented with solenoid valves up to 3” gas. Contact our technical
department for further information.

4.58
SOLENOID VALVES - SPECIAL PRODUCTS UPON REQUEST
MULTI-FUNCTION MODULES WITH BUILT-IN VACUUM SOLENOID VALVES

3D drawings are available on vuototecnica.net

Module A Module B Module C

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
4.59
SOLENOID VALVE ACCESSORIES AND SPARE PARTS
WITH LOW ABSORPTION ELECTRIC COIL
Solenoid pilot valves with built-in low absorption electrical coil
The solenoid valves are small three-way valves, driven by a built-in
electric coil, capable of managing compressed air or vacuum, for driving
solenoid valves.
3D drawings are available on vuototecnica.net

M an u a l
The electric coils of the solenoid pilot valves are fully plastic-coated a c t i va t i o n
in synthetic resin, watertight, insulation class F (up to 155°C) as per
standard VDE, with 3 mm two-terminal electrical connections for
connectors in compliance with EN 175301-803
(ex DIN 43650) - C.
Protection degree IP 54; IP 65 with connector inserted.
Tolerance permitted on the nominal voltage value: ±10%
Tolerance permitted on the frequency value: ±5%
Room temperature: from -10 to +45°C
Fluid temperature: from -10 to +95°C
Electrical power: from 1 to 2 W

SOLENOID PILOT VALVES WITH BUILT-IN LOW ABSORPTION ELECTRICAL COIL

Service Power Electrical voltage Pressure (bar) Weight
Item
ED W Volt min max g
00 07 301 100% 1 12 / 50 - 60Hz 0 8 32
00 07 302 100% 1 24 / 50 - 60Hz 0 8 32
00 07 303 100% 2 12 / DC 0 8 32
00 07 304 100% 2 24 / DC 0 8 32
For solenoid valves item
4 07 01 13 - 07 02 13 - 07 03 13 - 07 04 13 - 07 05 13 - 07 06 13 - 07 08 13 - 07 09 13
07 03 13 LP - 07 04 13 LP - 07 05 13 LP - 07 06 13 LP

00 07 305 100% 1 12 / 50 - 60Hz 0 1 32

00 07 306 100% 1 24 / 50 - 60Hz 0 1 32
00 07 307 100% 2 12 / DC 0 1 32
00 07 308 100% 2 24 / DC 0 1 32
For solenoid valves item
07 03 43 - 07 04 43 - 07 05 43

BISTABLE IMPULSE SOLENOID PILOT VALVES WITH BUILT-IN LOW ABSORPTION ELECTRICAL COIL
Service Power Electrical voltage Pressure (bar) Weight
Item
ED W Volt min max g
00 07 309 100% 1 12 / DC 0 8 30
00 07 310 100% 1 24 / DC 0 8 30
For solenoid valves item
07 01 53 - 07 02 53 - 07 03 53 - 07 04 53 - 07 05 53 - 07 06 53 - 07 08 53 - 07 09 53
07 03 53 LP - 07 04 53 LP - 07 05 53 LP - 07 06 53 LP

00 07 311 100% 1 12 / DC 0 1 30
00 07 366 100% 1 24 / DC 0 1 30
For solenoid valves item
07 03 63 - 07 04 63 - 07 05 63

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
4.60
SOLENOID VALVE SEALING KIT
WITH LOW ABSORPTION ELECTRIC COILS
Sealing kits are composed of a membrane, shutters and standard
O-rings installed on our compressed air and vacuum three-way
solenoid valves.
In the presence of very hot fluids (up to 250°C) or corrosive fluids,
3D drawings are available on vuototecnica.net

we can supply sealing kits in special compounds. Please contact our

technical department.

Complete kit for solenoid valves: 07 01 13 e 07 02 13 item 00 07 271

07 03 13 item 00 07 272
07 03 13 LP item 00 07 290
07 04 13 e 07 05 13 item 00 07 273
07 04 13 LP e 07 05 13 LP item 00 07 291
07 06 13 item 00 07 274
07 06 13 LP item 00 07 292
07 08 13 item 00 07 379
07 09 13 item 00 07 383

Complete kit for solenoid valves: 07 01 53 e 07 02 53 item 00 07 275

07 03 53 item 00 07 276
07 03 53 LP item 00 07 293
07 04 53 e 07 05 53 item 00 07 277
07 04 53 LP e 07 05 53 LP item 00 07 294
07 06 53 item 00 07 278
07 06 53 LP item 00 07 295
07 08 53 item 00 07 379
07 09 53 item 00 07 383

Complete kit for solenoid valves: 07 03 43 e 07 04 43 item 00 07 279

07 03 63 e 07 04 63 item 00 07 279
4 07 05 43 e 07 05 63 item 00 07 280

PILOT MEMBRANES FOR SOLENOID VALVES

WITH LOW ABSORPTION ELECTRIC COILS

For valves Connections Material Colour Dimensions mm

Item
item
00 07 104 07 03 43 - 07 04 43 G1/2” - G3/4” Reinforced NBR Black Ø 65
07 03 63 - 07 04 63
00 07 105 07 05 43 - 07 05 63 G1” Reinforced NBR Black Ø 76
00 07 229 07 01 13 - 07 01 53 G1/4” - G3/8” Vulkollan® Beige 49 x 35
07 02 13 - 07 02 53
00 07 230 07 03 13 - 07 03 53 G1/2” Urepan® 65 Grey - orange 62 x 39
00 07 296 07 03 13 LP - 07 03 53 LP G1/2” Vulkollan® Beige 62 x 39
00 07 231 07 04 13 - 07 04 53 G3/4” - G1” Urepan® 65 Grey - orange 79 x 49
07 05 13 - 07 05 53
00 07 297 07 04 13 LP - 07 04 53 LP G3/4” - G1 Vulkollan® Beige 79 x 49
07 05 13 LP - 07 05 53 LP
00 07 232 07 06 13 - 07 06 53 G1” 1/2 Urepan® 65 Grey - orange 129 x 89
00 07 298 07 06 13 LP - 07 06 53 LP G1” 1/2 Vulkollan® Beige 129 x 89

4.62
SUCTION FILTERS

FCL IN-LINE SUCTION FILTERS, WITH PAPER CARTRIDGE PG. 5.01 ÷ 5.02
PAPER FILTERING CARTRIDGES FOR FCL FILTERS PG. 5.02

3D drawings are available on vuototecnica.net

FB SUCTION FILTER WITH METAL CARTRIDGE PG. 5.03 ÷ 5.10
STAINLESS STEEL MESH FILTERING CARTRIDGES FOR FB FILTERS PG. 5.11
FC SUCTION FILTERS WITH PAPER CARTRIDGE PG. 5.12 ÷ 5.15
PAPER FILTERING CARTRIDGES FOR FC FILTERS PG. 5.16 ÷ 5.17
FO OIL-BATH SUCTION FILTERS PG. 5.18
STEEL WOOL FILTERING CARTRIDGES FOR FO FILTERS PG. 5.19
FO LONG OPERATION AUTONOMY OIL-BATH SUCTION FILTERS PG. 5.20
FS SYPHON SUCTION FILTERS PG. 5.21
SYPHON FILTER SYSTEM WITH AUTOMATIC BY-PASS FS 50 BP PG. 5.22
SPECIAL FILTERS PG. 5.23
FP SERIES FILTERING CARTRIDGE CONTAINERS WITH COMPRESSION SEALING PG. 5.24
FILTERING CARTRIDGES WITH COMPRESSION SEALING PG. 5.25
FM SERIES QUICK COUPLING FILTERING CARTRIDGE CONTAINERS PG. 5.26
FK SERIES QUICK COUPLING FILTERING CARTRIDGE CONTAINERS PG. 5.27
QUICK COUPLING FILTERING CARTRIDGES PG. 5.28

5
5
3D drawings are available on vuototecnica.net
FCL IN-LINE SUCTION FILTERS, WITH PAPER CARTRIDGE

These small in-line filters retain impurities and very fine dust, interfering
with the flow rate in a negligible manner. Thanks to their reduced size, they
can be directly installed onto vacuum piping, close to the utilities (vacuum
cups, vacuum clamping systems, etc.) for a fractionated filtration and a

3D drawings are available on vuototecnica.net

better visual control of all the plant suction points.
They are composed of a cylindrical transparent Plexiglass body closed by
two anodised aluminium flanges kept in place by Seeger rings, where all the
threaded male or female connections and seals are located. Inside there is
a filtering cartridge with a filtering degree equal to 7 μ, which is made with
a special treated paper that is pleated to increase the filtering surface. The
filters can be inspected by simply removing one of the two flanges. Due to
the paper filtering element, these filters are not recommended in presence
of water or oil vapours or condensations.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Fluid temperature: from -20 to +60°C
Level of filtration: 7 μ

Filter
cartridge

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item g 5
FCL 1 G1/4” 79.2 20.0 17 7.1 7.5 00 FCL 03 00 KIT FCL 1 120
FCL 2 G3/8” 83.6 24.0 20 9.3 20.0 00 FCL 03 00 KIT FCL 1 136
FCL 3 G1/2” 89.6 26.5 24 12.3 25.0 00 FCL 03 00 KIT FCL 1 152

Filter
cartridge

d A B C D E Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item g
FCL 1 M G1/4” 103.2 20.0 17 19.1 12 7.5 00 FCL 03 00 KIT FCL 1 122
FCL 2 M G3/8” 103.2 24.0 20 19.1 12 20.0 00 FCL 03 00 KIT FCL 1 138
FCL 3 M G1/2” 113.6 26.5 24 24.3 15 25.0 00 FCL 03 00 KIT FCL 1 154

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.01
FCL IN-LINE SUCTION FILTERS, WITH PAPER CARTRIDGE
3D drawings are available on vuototecnica.net

Filter
cartridge

d A B C D E F Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item g
FCL 1 MF G1/4” 91.2 20.0 17 19.1 12 7.1 7.5 00 FCL 03 00 KIT FCL 1 120
FCL 2 MF G3/8” 93.4 24.0 20 19.1 12 9.3 20 00 FCL 03 00 KIT FCL 1 136
5 FCL 3 MF G1/2” 101.6 26.5 24 24.3 15 12.3 25 00 FCL 03 00 KIT FCL 1 152

PAPER FILTERING CARTRIDGES FOR FCL FILTERS

The cartridges described below are suited for FCL filters.

They are made with a special treated paper with a filtering degree equal to 7 μ, which is
pleated in order to increase its surface and wrapped on two flanges in plastic material.
They are recommended for retaining impurities and fine dust, but not in presence of
water or oil vapours or condensations.

For filter D D1 H Level of filtration

Item
item Ø Ø micron
00 FCL 03 FCL 1 - FCL 2 - FCL 3 31 10 47 5÷7
FCL 1 M - FCL 2 M - FCL 3 M
FCL 1 MF - FCL 2 MF - FCL 3 MF

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.02
FB SUCTION FILTER WITH METAL CARTRIDGE

Preventing impurities from reaching the vacuum pump is fundamental to

guarantee the correct operation and long duration.
This range of filters, to be placed on the vacuum pump suction inlet or on the
plant pipeline, has been designed for this purpose. Their simple and rational

3D drawings are available on vuototecnica.net

structure features threaded connections for the installation and a lid, very
easy to open, to allow easily cleaning the filtering cartridge. The lids are made
with die-cast aluminium, as are the containers, except for the models FB 5,
FB 10 e FB 20 which are in transparent plastic material (cellulose acetate),
particularly resistant to shocks.
The standard filtering cartridges are in profiled stainless steel mesh, with
a filtering degree equal to 60 μ. Upon request, they can be supplied with a
filtering degree equal to 100 or 300 μ.
The flow rate of these filters ranges from 5 to 300 m3/h.
Technical features
Operating pressure: from 0.5 to 3000 absolute mbar
Fluid temperature: from -20 to +90°C for filters with aluminium
container, from -20 to +50°C for filters with containers in transparent plastic
material
Level of filtration: 60 μ

Filter
cartridge 5

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item g
FB 5 G1/4” 63 75.3 12.5 59 5 00 FB 03 00 KIT FB5 140

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.03
FB SUCTION FILTER WITH METAL CARTRIDGE
3D drawings are available on vuototecnica.net

M6 hex screw

Filter
cartridge

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item g
FB 10 G3/8” 81 87 17 79 10 00 FB 13 00 KIT FB10 258

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.04
FB SUCTION FILTER WITH METAL CARTRIDGE

3D drawings are available on vuototecnica.net

M6 hex screw

Filter
cartridge

Condensation
drain

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part and small parts
Ø Ø m3/h item item g
FB 20 G1/2” 81 116 17 79 20 00 FB 22 00 KIT FB20 312

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.05
FB SUCTION FILTER WITH METAL CARTRIDGE
3D drawings are available on vuototecnica.net

M6 hex screw

Filter
cartridge

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part and small parts
Ø Ø m3/h item item g
FB 20 A G1/2” 81 121 17 79 20 00 FB 22 00 KIT FB20 394

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.06
FB SUCTION FILTER WITH METAL CARTRIDGE

3D drawings are available on vuototecnica.net

M8 hex screw

Filter
cartridge

Condensation
drain

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part and small parts
Ø Ø m3/h item item g
FB 28 G3/4” 120 181 31 112 40 00 FB 34 00 KIT FB 30 762

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.07
FB SUCTION FILTER WITH METAL CARTRIDGE
3D drawings are available on vuototecnica.net

M8 hex screw

Filter
cartridge

Condensation
drain

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part and small parts
Ø Ø m3/h item item g
FB 30 G1” 120 181 31 112 70 00 FB 34 00 KIT FB 30 758

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.08
FB SUCTION FILTER WITH METAL CARTRIDGE

3D drawings are available on vuototecnica.net

M12 hex screw

Filter
cartridge

Condensation
drain

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part and small parts
Ø Ø m3/h item item g
FB 40 G1” 1/4 190 255 39 182 150 00 FB 45 00 KIT FB 40 3.06
FB 50 G1” 1/2 190 255 39 182 200 00 FB 45 00 KIT FB 50 2.99

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.09
FB SUCTION FILTER WITH METAL CARTRIDGE
3D drawings are available on vuototecnica.net

M12 hex screw

Filter
cartridge

Condensation
drain

d A B C D Flow rate Cartridge Sealing kit Weight

Item max spare part and small parts
Ø Ø m3/h item item g
FB 60 G2” 182 260 42 182 300 00 FB 52 00 KIT FB 60 3.18

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.10
STAINLESS STEEL MESH FILTERING CARTRIDGES FOR FB FILTERS

The cartridges described on this page are suited for FB suction filters.
The standard ones are made with profiled stainless steel mesh with a
filtering degree equal to 60 μ.
Upon request, the same cartridges can be supplied with a filtering

3D drawings are available on vuototecnica.net

degree equal to 100 or 300 μ.
They are recommended for retaining impurities even in presence of
water and oil vapours or condensations, but not for retaining fine and
impalpable dust.

For filter D D1 D2 H Level of filtration

Item
item Ø Ø Ø micron
00 FB 03 FB 5 35 6 10.0 34 60
00 FB 13 FB 10 58 16 25.5 34 60
00 FB 22 FB 20 - FB 20A 58 16 25.5 67 60
00 FB 34 FB 28 - FB 30 74 16 25.5 87 60

For filter D D1 D2 H Level of filtration

Item
item Ø Ø Ø micron
00 FB 45 FB 40 - FB 50 95 39 49 160 60
00 FB 52 FB 60 95 51 56 160 60
Note: Upon request, the same cartridges can be supplied with a filtering degree equal to 100 or 300 μ.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.11
FC SUCTION FILTERS WITH PAPER CARTRIDGE

These filters have been designed to allow vacuum pumps to operate even in very
dusty environments. Installed onto the pump suction inlet, they are able to retain
fine and impalpable dust interfering with the flow rate in a negligible manner.
The filtering cartridge is made with a special treated paper with a filtering degree
3D drawings are available on vuototecnica.net

equal to 5 - 7 μ, which is pleated to increase its surface and is contained in a

double perforated sheet steel enclosure. The filtering cartridge container as well as
the lid are made with sheet steel and varnished with a special anti-oxidation paint.
A seal located between the lid and the container guarantees a perfect vacuum
seal between the two elements. The release clamps applied onto the container
allow a quick opening of the lid for the filtering cartridge inspection or
replacement.
Due to the paper filtering element, these filters are not recommended in
presence of water or oil vapours or condensations.
Technical features
Operating pressure: from 0.5 to 2000 absolute mbar
Fluid temperature: from -20 to +60 °C
Level of filtration: 5 - 7 μ

Seal

Filter
Seal
cartridge

d A B C D E F Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item g
FC 10 G3/8” 79 70 9 72 49 37 15 00 FC 04 00 KIT FC 10 352
FC 20 G1/2” 93 80 13 96 67 51 30 00 FC 08 00 KIT FC 20 774
FC 25 G3/4” 93 80 13 96 67 51 50 00 FC 08 00 KIT FC 25 734

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.12
FC SUCTION FILTERS WITH PAPER CARTRIDGE

3D drawings are available on vuototecnica.net

Seal

Filter
Seal
cartridge

d A B C E F G Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø m3/h item item Kg
FC 30 G1” 105 92 13 84 41 64 90 00 FC 15 00 KIT FC 30 1.17
FC 35 G1” 1/4 97 84 13 78 46 51 100 00 FC 15 00 KIT FC 35 1.02
FC 38 G1” 1/2 101 88 13 80 45 56 200 00 FC 15 00 KIT FC 38 0.95
FC 55 G2” 170 157 13 81 79 91 300 00 FC 33 00 KIT FC 55 1.29

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.13
FC SUCTION FILTERS WITH PAPER CARTRIDGE
3D drawings are available on vuototecnica.net

Seal

Filter
Seal
cartridge

d A B D E F G Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item Kg
FC 40 G1” 1/4 161 125 162 102 77 84 150 00 FC 22 00 KIT FC 40 1.83
FC 50 G1” 1/2 197 161 160 100 85 112 200 00 FC 24 00 KIT FC 50 2.11

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.14
FC SUCTION FILTERS WITH PAPER CARTRIDGE

3D drawings are available on vuototecnica.net

Seal

Filter
Seal
cartridge

d A B C D E F G Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø m3/h item item Kg
FC 60 G2” 258 235 23 185 115 126 132 300 00 FC 29 00 KIT FC 60 4.62
FC 80 G3” 270 246 24 185 125 126 144 360 00 FC 29 00 KIT FC 80 3.45
FC 100 G4” 336 311 25 295 166 134 202 540 00 FC 34 00 KIT FC 100 5.56

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.15
PAPER FILTERING CARTRIDGES FOR FC FILTERS

The cartridges described on this page are suited for FC suction filters.
They are made with a special treated paper with a filtering degree
equal to 5 - 7 μ, which is pleated to increase its surface and is
contained in a double perforated sheet steel enclosure.
3D drawings are available on vuototecnica.net

They are recommended for retaining fine and impalpable dust, but not
in presence of water and oil vapours and condensation.

For filter D D2 H Level of filtration

Item
item Ø Ø micron
00 FC 04 FC 10 50 23 59 5÷7
00 FC 08 FC 20 - FC 25 64 38 69 5÷7

For filter D D1 D2 H Level of filtration

Item
item Ø Ø Ø micron
00 FC 15 FC 30 - FC 35 - FC 38 98 60 60 70 5÷7
00 FC 22 FC 40 126 64 64 125 5÷7
00 FC 24 FC 50 126 64 64 156 5÷7
00 FC 33 FC 55 98 60 64 140 5÷7

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.16
PAPER FILTERING CARTRIDGES FOR FC FILTERS

3D drawings are available on vuototecnica.net

For filter D D1 D2 H Level of filtration
Item
item Ø Ø Ø micron
00 FC 29 FC 60 - FC 80 152 89 89 215 5÷7

For filter D D1 D2 H Level of filtration

Item
item Ø Ø Ø micron
00 FC 34 FC 100 227 178 178 278 5÷7

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.17
FO OIL-BATH SUCTION FILTERS

In presence of a considerable amount of fine or impalpable dust, the traditional suction

filter would require a cartridge with a filtering degree so high that, along with reducing its
operation autonomy, it would also reduce the vacuum pump suction flow rate.
Oil-bath suction filters have been studied in order to overcome this problem.
3D drawings are available on vuototecnica.net

The main feature of these filters is the ability to retain the smallest and most impalpable
dust particles, without reducing the vacuum pump suction flow rate.
Oil-bath filters are composed of a sheet steel head and container coupled with an
interposed seal and clamped by release clamps.
Inside, besides the oil bowl, there are two steel wool filtering cartridges, one of which is
detachable and washable, while the other is fixed. The release clamps guarantee easy
access for cleaning operations.
They can be used with any kind of oil, even drain oil, as long as it has a minimum
viscosity degree. The ideal oil is the same one used for the pump.
Oil-bath suction filters are not recommended for dry vacuum pumps.
They are currently available for capacities up to 300 m3/h.
Technical features
Operating pressure: from 0.5 to 2000 absolute mbar
Fluid temperature: from -20 to +90 °C
Level of filtration: ≤1 μ

Seal

Fixed
cartridge

Mobile
Oil
cartridge

d A B C D E F G H I Flow rate Cartridge Sealing kit Weight

Item max spare part spare part
Ø Ø Ø m3/h item item Kg
FO 20 G1/2” 205 85 112 106 8 100 40 156 49 30 00 FO 04 00 KIT FO 20 1.44
FO 30 G1” 210 88 106 129 16 106 50 151 59 90 00 FO 09 00 KIT FO 30 1.84
FO 50 G1” 1/2 305 110 135 160 60 128 60 199 106 200 00 FO 14 00 KIT FO 50 2.76
FO 60 G2” 340 140 140 185 60 142 67 217 123 300 00 FO 19 00 KIT FO 60 3.70

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.18
STEEL WOOL FILTERING CARTRIDGES FOR FO FILTERS

The cartridges described on this page are suited for FO oil-bath

suction filters.
They are made with pressed steel wool contained in a double
perforated sheet steel enclosure. Their function is to retain fine or

3D drawings are available on vuototecnica.net

impalpable dust impregnated with the filter oil.

For filter D D1 D2 H Level of filtration

Item (installed on the filter)
item Ø Ø Ø micron
00 FO 04 FO 20 110 40 103 70 ≤1
00 FO 09 FO 30 134 49 127 72 ≤1
00 FO 14 FO 50 165 58 155 86 ≤1
00 F0 19 FO 60 190 66 180 104 ≤1

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.19
FO LONG OPERATION AUTONOMY OIL-BATH SUCTION FILTERS

In presence of fine or impalpable dust, the traditional suction filter would require
a cartridge with a filtering degree so high that, along with reducing its operation
autonomy, it would also reduce the vacuum pump suction flow rate.
Oil-bath suction filters have been studied in order to overcome this problem.
3D drawings are available on vuototecnica.net

The main feature of these filters, in addition to their high autonomy, is their
ability to retain the finest suctioned impalpable dusts without reducing the
suction flow rate of the pump.
Oil-bath filters are composed of a sheet steel head and container coupled with
an interposed seal and clamped by release clamps.
Inside, besides the oil bowl, there are two steel wool filtering cartridges, one of
which is detachable and washable, while the other is fixed. The release clamps
guarantee easy access for cleaning operations.
Two visual indicators allow monitoring of the oil level and the degree of clogging.
They can be used with any kind of oil, even drain oil, as long as it has a minimum
viscosity degree. The ideal oil is the same one used for the pump.
Oil-bath suction filters are not recommended for dry vacuum pumps.
They are currently available for 200 and 300 m3/h capacities.
Technical features
Operating pressure: from 0.5 to 2000 absolute mbar
Temperature of fluid: from -20 to +90°C
Level of filtration: ≤1 μ
Quantity of oil: FO 160 - 6.3 L
FO 300 - 12.5 L

5
Filter
cartridge

Seal

Visual level
indicators

d A B C D E F G H I L Flow rate Sealing Weight

Item max spare part
Ø Ø Ø Ø m3/h item Kg
FO 160 G1” 1/2 250 100 508 290 308 32.5 12 910 356 140 200 00 FO 30 27
FO 300 G2” 350 80 508 390 308 32.5 12 920 356 200 300 00 FO 29 40
Note: Filter cartridges are washable and therefore do not need to be replaced.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.20
FS SYPHON SUCTION FILTERS

These filters retain impurities and liquids extracted through vacuum cups or vacuum clamping systems,
preventing them from entering into the vacuum pumps.
They are composed of:
- A transparent Plexiglas cylindrical container with an extractable lid to allow inspection and cleaning

3D drawings are available on vuototecnica.net

- A check valve located on the suction inlet for preventing the air from returning in the filter when the
pump is idle
- A stainless steel mesh filtering cartridge with a filtering degree equal to 60 μ, also located
on the suction inlet to retain dust and solid impurities
- A two-way manual valve for service vacuum interception.
- A two-way manual valve for restoring the atmospheric pressure inside the filter
- A radial vacuum gauge the direct reading of the level of vacuum
- A magnetic level switch that stops the pump when the suctioned liquid exceeds
the safety level
- A rigid pipe connected to the service to convey the air flow and the sucked liquid
to the bottom of the container
- A check valve at the bottom of the filter to automatically drain the sucked liquid
and impurities every time the atmospheric pressure is restored inside the filter
- A cock applied on the aforementioned check valve for manual liquid drainage
- A sturdy metal bracket for fixing the filter to the wall
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Fluid temperature: from -5 to +50°C
Level of filtration: 60 μ

Vacuum
gauge

Seal
Magnetic
Filter sensor 5
cartridge

d A B C D E G H I L M N O P Flow rate Capacity Cartridge Vacuum gauge Sealing Weight

Item max spare part spare part spare part
Ø Ø Ø m3/h L item item item Kg
FS 5 G3/8” 461 130 175 200 25 100 250 111 150 25 140 10 136 10 6.0 00 FB 03 09 05 10 00 FS 36 5.5
FS 10 G3/8” 551 130 175 200 25 100 340 111 150 25 140 10 136 10 8.5 00 FB 22 09 05 10 00 FS 36 6.0
FS 20 G1/2” 630 130 175 200 25 100 410 120 150 25 140 10 145 20 10.5 00 FB 22 09 05 10 00 FS 36 6.8
FS 25 G3/4” 750 150 195 240 25 100 510 140 170 30 170 11 180 40 19.5 00 FB 22 09 05 10 00 FS 36 9.1
FS 30 G1” 890 190 225 300 30 120 610 160 200 40 205 11 220 70 38.0 00 FB 34 09 05 10 00 FS 41 19.2
FS 50 G2” 960 190 225 300 30 120 610 240 200 40 250 11 276 300 38.0 00 FB 45 09 05 10 00 FS 41 22.7

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.21
SYPHON FILTER SYSTEMS WITH AUTOMATIC BY-PASS FS 50 BP and FS 60 BP

The system, composed of two siphon filters, operates initially with suction through filter 1 and with filter 2 excluded. When the suctioned liquid
reaches the float on the level switch, automatically by means of the 1” 1/2 three-way vacuum interception solenoid valve for item FS 50 BP and 2” for
item FS 60 BP, an exchange is made and suction passes through filter 2.
The input of atmospheric air into filter 1 via the ½” three-way solenoid valve installed on its lid, accumulated liquid is allowed to discharge
3D drawings are available on vuototecnica.net

automatically through the check valve with tap on the bottom of the filter. Once liquid has been discharged, after a pre-set time (this operation can be
timed), the solenoid valve returns to its initial position, thus allowing recreation of a vacuum inside the filter through a small flexible hose connected
to the main vacuum piping.
With this arrangement, there will not be any decrease in the level of vacuum for use when the suction exchange will be carried out between the two
filters. This exchange will take place when the liquid reaches the level switch float on filter 2 and, from that moment, the operations described above
will be repeated.
The filter system is composed of:
- 2 Plexiglas siphon filters with aluminium lids and complete with accessories, with a flow rate of 38 L each
- 2 1” 1/2 gas three-way servo-operated vacuum solenoid valves, item 07 06 13 for item FS 50 BP
and 2” gas servo-operated vacuum solenoid valves, item 07 08 13 for item FS 60 BP
- 2 ½” gas three-way servo-operated vacuum solenoid valves, item 07 03 13.
- 4 1” 1/2 gas two-way manual valves for vacuum interception, item 13 07 10 for item FS 50 BP
and 2” gas for vacuum interception, item 13 08 10 for item FS 60 BP
- 2 Manual ½” gas two-way valves, for atmospheric air input, item 13 03 10
- 1 Switchgear enclosed in a special watertight metal box, for single phase electrical voltage Volt 230/ 50 Hz
- 1 Coated profile steel frame to mount all above-described components
The siphon filter system with automatic by-pass is recommended in all those cases in which there is a strong presence of liquid in suction fluids and
where machine shut-down for the discharge of liquids suctioned by traditional siphon filters is not allowed.
Technical features
Operating pressure: from 0.5 to 2000 absolute mbar
Fluid temperature: from -5 to +50°C
Level of filtration: 60 μ

Switchgear
For Ø8 ext. hose

X = Compressed air supply

A = Use
P = Pump
R = Discharge

A B G H Flow rate Capacity Cartridge Vacuum gauge Sealing Weight

Item max spare part spare part spare part
m3/h L item item item kg
FS 50 BP 1350 1000 G1” 1/2 1180 200 38 x 2 00 FB 45 09 05 10 00 FS 41 130
FS 60 BP 1350 1050 G2” 1200 300 38 x 2 00 FB 45 09 05 10 00 FS 41 136

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.22
SPECIAL FILTERS

2FS50BPM1

GAFL01M1
3D drawings are available on vuototecnica.net

5.23
5
FP SERIES FILTERING CARTRIDGE CONTAINERS WITH COMPRESSION SEALING

The containers of the FP series are suited for the filtering cartridges with compression
sealing and are composed of a transparent plastic container and a blue plastic head
screwed together with an interposed seal. The number after the item indicates the
length in inches of the necessary filtering cartridge.
3D drawings are available on vuototecnica.net

The cartridge can be chosen in various materials:

pleated paper, pleated polypropylene mesh and stainless steel mesh AISI 304.
The following pages describe the filtering cartridges with compression sealing,
with all the indications regarding dimensions, materials and filtering degree of each one
of them.
Technical features
Operating pressure: from 0.5 to 9000 absolute mbar
Temperature of suctioned fluid: from -10 to 45°C

4 holes for
Ø 4.2 for fixing

Spanner Item NP

d A B C D E F Max flow rate Cartridge For cartridge Weight

Item
Ø Ø m3/h length item Kg
FP 25/4 G3/4” 130 163 21 130 49 50 70 4” SP/4 - SS/4 - SA/4 0.84
FP 30/4 G1” 143 169 24 130 50 51 100 4” SP/4 - SS/4 - SA/4 0.91
FP 25/7 G3/4” 130 250 21 130 49 50 70 7” SP/7 - SS/7 - SA/7 0.96
FP 30/7 G1” 143 253 24 130 50 51 100 7” SP/7 - SS/7 - SA/7 1.03
NP Spanner for tightening the tray
Note: The filtering cartridge is not an integral part of the filter and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.24
FILTERING CARTRIDGES WITH COMPRESSION SEALING

The filtering cartridges described on this page, once installed on their

container, are able to retain the impurities and dust contained in the
sucked fluid, interfering with the vacuum pump or generator flow rate
in a negligible manner.

3D drawings are available on vuototecnica.net

They are produced with different materials that can be identified with
the following abbreviations:
- Series SP. Pleated paper filtering cartridge with
compression sealing.
- Series SS. Pleated polypropylene mesh filtering
cartridge with compression sealing.
- Series SA. AISI 304 stainless steel mesh filtering
cartridge with compression sealing.
The number after the item indicates the length in
inches of the filtering cartridge.

Seal

D D1 D2 H Cartridge For container Level of filtration

Item
Ø Ø Ø length item micron
SP/4 70 30 30 98 4” FP 25/4 - FP 30/4 25
SP/7 70 30 30 170 7” FP 25/7 - FP 30/7 25
SS/4 70 30 30 98 4” FP 25/4 - FP 30/4 50
SS/7 70 30 30 170 7” FP 25/7 - FP 30/7 50
SA/4 70 30 30 98 4” FP 25/4 - FP 30/4 50
SA/7 70 30 30 170 7” FP 25/7 - FP 30/7 50

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.25
FM SERIES QUICK COUPLING FILTERING CARTRIDGE CONTAINERS

The containers of the FM series are suited for quick coupling filtering cartridges and are composed of a
transparent SAN (Styrene-acrylic nitrile) container and a head with a reinforced polypropylene ring nut,
coupled together with an interposed seal.
The number after the item indicates the length in inches of the necessary filtering cartridge.The cartridge can
3D drawings are available on vuototecnica.net

be chosen in various materials: pleated paper, pleated polypropylene mesh and AISI 304 stainless steel
mesh. The quick coupling filtering cartridges are described on page 5.28, with all the indications regarding
dimensions, materials and filtering degree of each one of them.
Technical features
Operating pressure: from 0.5 to 9000 absolute mbar
Temperature of suctioned fluid: from -10 to 45°C

4 holes for
self-threading screws

Spanner Item NP

d A B C D E F Max flow rate Cartridge For cartridge Weight

Item
Ø Ø m3/h length item Kg
FM 20/7 G1/2” 133 241 18 100 48 49 30 7” RP/7 - RS/7 - RA/7 0.74
FM 25/7 G3/4” 133 241 21 100 49 50 70 7” RP/7 - RS/7 - RA/7 0.87
FM 30/7 G1” 145 247 24 100 50 51 100 7” RP/7 - RS/7 - RA/7 0.89
FM 25/10 G3/4” 133 315 21 100 49 50 70 10” RP/10 - RS/10 - RA/10 0.86
FM 30/10 G1” 145 321 24 100 50 51 100 10” RP/10 - RS/10 - RA/10 0.93
FM 40/10 G1” 1/4 145 345 35 100 50 51 160 10” RP/10/57 - RS/10/57 - RA/10/57 1.08
FM 50/10 G1” 1/2 145 345 35 100 50 51 200 10” RP/10/57 - RS/10/57 - RA/10/57 1.06
FM 60/10 G2” 145 345 35 100 50 51 300 10” RP/10/57 - RS/10/57 - RA/10/57 1.08
FM 40/20 G1” 1/4 145 600 35 100 50 51 160 20” RP/20/57 - RS/20/57 - RA/20/57 1.36
FM 50/20 G1” 1/2 145 600 35 100 50 51 200 20” RP/20/57 - RS/20/57 - RA/20/57 1.34
FM 60/20 G2” 145 600 35 100 50 51 300 20” RP/20/57 - RS/20/57 - RA/20/57 1.36
NF Spanner for tightening the ring nut
Note: The filtering cartridge is not an integral part of the filter and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.26
FK SERIES QUICK COUPLING FILTERING CARTRIDGE CONTAINERS

The containers of the FK series are suited for quick coupling filtering cartridges and are
composed of a transparent PET (Polyethylene terephthalate) container and a head with
a brass ring nut coupled together with an interposed seal.
The number after the item indicates the length in inches of the necessary filtering

3D drawings are available on vuototecnica.net

cartridge.
The cartridge can be chosen in various materials: pleated paper, pleated polypropylene
mesh and AISI 304 stainless steel mesh. The quick coupling filtering cartridges are
described on page 5.28, with all the indications regarding dimensions, materials and
filtering degree of each one of them.
Technical features
Operating pressure: from 0.5 to 9000 absolute mbar
Temperature of suctioned fluid: from -10 to 45°C

4 holes for
Spanner Item NK
Ø 4.2 for fixing

d A B C D E F Max flow rate Cartridge For cartridge Weight

Item
Ø Ø m3/h length item Kg
FK 25/7 G3/4” 120 265 24 100 25 75 70 7” RP/7 - RS/7 - RA/7 1.64
FK 30/7 G1” 120 270 27 100 25 75 100 7” RP/7 - RS/7 - RA/7 1.88
FK 25/10 G3/4” 130 335 24 100 25 75 70 10” RP/10 - RS/10 - RA/10 2.12
FK 30/10 G1” 130 335 27 100 25 75 100 10” RP/10 - RS/10 - RA/10 2.35
FK 50/10 G1” 1/2 130 345 30 100 25 75 200 10” RP/10/57 - RS/10/57 - RA/10/57 2.58
FK 60/10 G2” 130 350 33 100 25 75 300 10” RP/10/57 - RS/10/57 - RA/10/57 2.69
FK 30/20 G1” 130 540 27 100 25 75 100 20” RP/20 - RS/20 - RA/20 2.97
FK 50/20 G1” 1/2 130 600 30 100 25 75 200 20” RP/20/57 - RS/20/57 - RA/20/57 3.20
FK 60/20 G2” 130 600 33 100 25 75 300 20” RP/20/57 - RS/20/57 - RA/20/57 3.31
NK Spanner for tightening the tray
Note: The filtering cartridge is not an integral part of the filter and, therefore, must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
5.27
QUICK COUPLING FILTERING CARTRIDGES

The filtering cartridges described on this page, once installed on their

container, are able to retain the impurities and dust contained in the
sucked fluid, interfering with the vacuum pump or generator flow rate
in a negligible manner.
3D drawings are available on vuototecnica.net

They are produced with different materials that can be identified with
the following abbreviations:
- Series RP. Pleated paper quick coupling filtering cartridge with
double O-ring.
- Series RS. Pleated polypropylene mesh quick coupling filtering
cartridge with double O-ring.
- Series RA. AISI 304 stainless steel mesh quick coupling filtering
cartridge with double O-ring.
The number after the item indicates the length in inches of the
filtering cartridge.

Seal

A B D Cartridge For container Level of filtration

Item
Ø Ø length item micron
RP/7 45 173 70 7” FM20/7 FM25/7 FM30/7 - FK25/7 FK30/7 25
RP/10 45 250 70 10” FM25/10 FM30/10 - FK25/10 FK30/10 25
RP/10/57 57 250 70 10” FM40/10 FM50/10 FM60/10 - FK50/10 FK60/10 25
RP/20 45 505 70 20” FK30/20 25
RP/20/57 57 505 70 20” FM40/20 FM50/20 FM60/20 - FK50/20 FK60/20 25
RS/7 45 173 70 7” FM20/7 FM25/7 FM30/7 - FK25/7 FK30/7 50
RS/10 45 250 70 10” FM25/10 FM30/10 - FK25/10 FK30/10 50
RS/10/57 57 250 70 10” FM40/10 FM50/10 FM60/10 - FK50/10 FK60/10 50
RS/20 45 505 70 20” FK30/20 50
RS/20/57 57 505 70 20” FM40/20 FM50/20 FM60/20 - FK50/20 FK60/20 50
RA/7 45 173 70 7” FM20/7 FM25/7 FM30/7 - FK25/7 FK30/7 50
RA/10 45 250 70 10” FM25/10 FM30/10 - FK25/10 FK30/10 50
RA/10/57 57 250 70 10” FM40/10 FM50/10 FM60/10 - FK50/10 FK60/10 50
RA/20 45 505 70 20” FK30/20 50
RA/20/57 57 505 70 20” FM40/20 FM50/20 FM60/20 - FK50/20 FK60/20 50

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
5.28
VACUUM FITTINGS AND HOSES

HOSE ENDS PG. 6.01

FITTINGS AND CAPS PG. 6.02 ÷ 6.03

3D drawings are available on vuototecnica.net

ROTATING QUICK COUPLING FITTINGS PG. 6.04
COMPRESSED AIR AND VACUUM FLEXIBLE HOSES AND RELATIVE FITTINGS PG. 6.05
TPR FLEXIBLE HOSE FITTINGS PG. 6.06

6
6
3D drawings are available on vuototecnica.net
HOSE ENDS

Our hose ends are traditional barbed nickel-plated

and brass fittings.
They are suited for connecting smooth or reinforced
flexible hoses with an internal diameter up to 76 mm.

3D drawings are available on vuototecnica.net

Hex. C

d A C D E F G H Material Weight
Item
Ø Ø Ø g
RS 1/4” G1/4” 9 17 5 5 18 12 35 nickel-plated brass 20
RS 3/8” G3/8” 13 19 9 5 20 8 33 nickel-plated brass 30
RS 1/2” G1/2” 16 23 12 5 25 10 40 nickel-plated brass 50
RS 3/4” G3/4” 21 28 16 8 35 12 55 nickel-plated brass 90
RS 1” G1” 27 36 22 8 35 12 55 nickel-plated brass 130
RS 1” 1/4 G1” 1/4 35 44 28 10 42 15 67 nickel-plated brass 270
RS 1” 1/2 G1” 1/2 40 50 33 10 45 15 70 nickel-plated brass 320
RS 3” G3” 76 100 66 10 60 30 100 nickel-plated iron 1450

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
6.01
FITTINGS AND CAPS

The fittings described on this page are particularly suitable for

connecting vacuum cup holders to their manifolds and in all those
cases that require a connection to vacuum sources via smooth
flexible hoses with internal diameters of 4, 6 and 9 mm, which is the
3D drawings are available on vuototecnica.net

maximum allowed for a vacuum hose with no internal reinforcement.

These are semi-rapid fittings. The hose is fixed by manually screwing
the reeded bush with no need for keys.
The threaded connections are male or female, according to the
requirements. The range is completed by L and T-type fittings and
caps with O-rings.
The fittings are a available in practical 10 or 50-piece packages and
are supplied with their nylon seal.

Hex. C

Bush

MALE FITTING
d A B C D E L Fitting Bush Weight
Item
Ø Ø int. hose Ø material material g
RM M5 M5 5.0 3.5 10 4 10 19.5 tropicalised iron anodised aluminium 6
RM 1/8” G1/8” 7.0 4.5 14 4 13 24.5 anodised aluminium anodised aluminium 6
RM 1/4” G1/4” 8.5 5.0 17 6 15 27.0 anodised aluminium anodised aluminium 10
RM 3/8” G3/8” 10.5 5.0 19 9 20 32.5 anodised aluminium anodised aluminium 18

Hex. C

Fitting Bush

FEMALE FITTING
d A C D E L Fitting Bush Weight
Item
Ø Ø int. hose Ø material material g
RF 1/8” G1/8” 14 14 4 13 27.0 anodised aluminium anodised aluminium 8
RF 1/4” G1/4” 16 17 6 15 30.0 anodised aluminium anodised aluminium 12
RF 3/8” G3/8” 20 19 9 20 32.5 anodised aluminium anodised aluminium 16

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
6.02
FITTINGS AND CAPS

3D drawings are available on vuototecnica.net

L-FITTING
d A E L Fitting Weight
Item
Ø material g
RL M5 M5 4.5 10 15.0 anodised aluminium 2
RL 1/8” G1/8” 7.0 16 24.0 anodised aluminium 10
RL 1/4” G1/4” 9.0 22 30.0 anodised aluminium 22
RL 3/8” G3/8” 11.0 25 32.5 anodised aluminium 30

T-FITTING
d A E L Fitting Weight
Item
Ø material g
RT M5 M5 4.5 10 15.0 anodised aluminium 1
RT 1/8” G1/8” 7.0 16 24.0 anodised aluminium 9
RT 1/4” G1/4” 9.0 22 30.0 anodised aluminium 21
RT 3/8” G3/8” 11.0 25 32.5 anodised aluminium 29 6

Hex. C

O-ring

CAP WITH O-RING

d A C D L Fitting Weight
Item
Ø Ø material g
00 15 291 M5 4 2.5 8 6.5 nickel-plated brass 1
00 11 44 G1/8” 7 3.0 15 9.5 nickel-plated brass 6
00 11 06 G1/4” 8 6.0 18 11.0 nickel-plated brass 10
00 18 33 G3/8” 9 8.0 21 12.5 nickel-plated brass 18
00 15 273 G1/2” 11 10.0 26 14.5 nickel-plated brass 21

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
6.03
ROTATING QUICK COUPLING FITTINGS

Quick coupling fittings are composed of a jack with hose end connector and a threaded
male coupler which connects itself to the jack.
They are fixed by a ball ring pushed by a spring. A nitrile rubber seal guarantees a perfect
vacuum seal.
3D drawings are available on vuototecnica.net

The structure of this type of fitting allows the two components to rotate freely at a low
speed and to rapidly couple and disconnect by manually acting on the jack reeded ring
nut. These fittings are fully made with brass and are available in various sizes.
The two components of the fittings are quick coupling and are not self-retaining.
These fittings are made entirely of brass and are available in various sizes.

Hose end

Coupler

Hex. C

d A C D E F G H L Material Hose end Hose end Coupling Coupling

Item weight weight
Ø Ø Ø item g item g
RR 3/8” G3/8” 30 21 13 29.5 39.5 14 10.5 83.0 brass 00 RR 3/8 02 100 00 RR 3/8 01 38
RR 1/2” G1/2” 30 21 16 30.5 38.5 14 10.5 83.0 brass 00 RR 1/2 02 104 00 RR 1/2 01 34
RR 3/4” G3/4” 30 26 20 29.0 38.5 15 10.5 82.5 brass 00 RR 3/4 02 118 00 RR 3/4 01 50
RR 1” G1” 38 34 25 30.0 40.0 17 12.0 87.0 brass 00 RR 1 02 166 00 RR 1 01 92
RR 1” 1/4 G1” 1/4 68 42 35 49.5 49.5 24 13.5 123.0 brass 00 RR 1 1/4 02 568 00 RR 1 1/4 01 210
RR 1” 1/2 G1” 1/2 68 48 40 49.0 54.0 25 17.0 128.0 brass 00 RR 1 1/2 02 710 00 RR 1 1/2 01 250
Max rotation speed - 38 rpm

Sp N

Coupler

Sp T

Sp C
Fitting

A C D d E F G H L M N R T Material Fitting Fitting Coupling Coupling

Item weight weight
Ø Ø Ø Ø item g item g
RRF 3/8” 24.5 -- G3/8” G3/8” 37 19.0 15 -- 71.0 -- 22 -- 22 brass 00 RRF 3/8 02 77 00 RRF 3/8 01 58
RRF 1/2” 27.5 -- G1/2” G1/2” 37 18.0 15 -- 70.0 -- 26 -- 24 brass 00 RRF 1/2 02 79 00 RRF 1/2 01 72
RRF 3/4” 32.0 -- G3/4” G3/4” 37 19.0 15 -- 71.0 -- 30 -- 28 brass 00 RRF 3/4 02 149 00 RRF 3/4 01 132
RRF 1” 40.0 -- G1” G1” 36 22.5 15 -- 73.5 -- 38 -- 32 brass 00 RRF 1 02 369 00 RRF 1 01 355
RRFF 3/8” 24.5 22 G3/8” -- -- 20.0 -- 42 -- 62.0 22 G3/8” -- brass 00 RRFF 3/8 02 82 00 RRF 3/8 01 58
RRFF 1/2” 27.5 24 G1/2” -- -- 18.0 -- 42 -- 60.0 26 G1/2” -- brass 00 RRFF 1/2 02 80 00 RRF 1/2 01 72
RRFF 3/4” 32.0 30 G3/4” -- -- 20.0 -- 42 -- 62.0 30 G3/4” -- brass 00 RRFF 3/4 02 199 00 RRF 3/4 01 132
RRFF 1” 40.0 38 G1” -- -- 22.5 -- 56 -- 78.5 38 G1” -- brass 00 RRFF 1 02 409 00 RRF 1 01 355
Note: Add the letter V to the item for fittings supplied with a Viton seal (Example: RRF 1”V).
Max rotation speed - 38 rpm

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
6.04
COMPRESSED AIR AND VACUUM FLEXIBLE HOSES AND RELATIVE FITTINGS

TPL flexible hoses are made with Polyamide 11 of vegetable derivation and are suited for compressed air
and vacuum for internal diameters up to 9 mm, as well as for compressed air only.
They feature a good flexibility and are lightweight, very low water absorption and excellent mechanical
performance. They also feature an excellent resistance to low and high temperatures, chemical agents,

3D drawings are available on vuototecnica.net

pneumatic pressure and ageing.
Our TPR flexible hoses have been specially designed for vacuum and are composed of a single piece with
plastic insulation and self-extinguishing materials, including the hose reinforcement core. Their excellent
flexibility ensures minimal bending radius and are very light in
relation to their great resistance to crushing.
Their smooth inside allows reducing harmful load losses to the
minimum.
The excellent functionality of these flexible hoses is associated
with a high resistance to abrasion, to weather agents and most
chemical products.
TPL flexible hose connection is ensured by the previously
described fittings, while we have created a completely new line
of RTPR fittings for TPR hoses. RTPR fittings from 3/8” to 1” are
made of self-extinguishing PVC. The larger ones are made of
nickel-plated metal.
The fittings are all extremely sturdy and offer a provide vacuum
seal. The use of these fittings eliminates unsightly hose clamps
and make the connection much faster and safer. They are
available in various sizes, depending on the diameter of the hose
to be connected.

TPL HOSE
d D Bending Weight Package Material Standard
Item
Ø int. Ø ext. radius g/m m colour
TPL 2 2.5 4 20 8.0 100 polyamide 11 light blue
TPL 4 4.0 6 30 19.5 100 polyamide 11 light blue
TPL 6 6.0 8 40 20.5 100 polyamide 11 light blue
TPL 8 8.0 10 60 24.0 100 polyamide 11 light blue
TPL 9 9.0 12 70 28.0 50 polyamide 11 light blue 6
TPL 12 12.0 15 95 67.0 50 polyamide 11 light blue
TPL 16 16.0 18 130 56.0 50 polyamide 11 light blue
TPL 18 18.0 22 300 133.0 50 polyamide 11 light blue
Operating temperature: -40° / +70°C Other colours upon request

TPR HOSE
d D Bending Weight Package Material Standard
Item
Ø int. Ø ext. radius g/m m colour
TPR 3/8” 12.7 17.8 60 150 30 pvc grey
TPR 1/2” 16.2 21.1 80 170 30 pvc grey
TPR 3/4” 21.3 26.4 105 230 30 pvc grey
TPR 1” 27.0 33.1 135 370 30 pvc grey
TPR 1” 1/4 35.7 41.8 175 500 30 pvc grey
TPR 1” 1/2 40.6 47.8 200 630 30 pvc grey
TPR 2” 51.9 59.8 260 900 30 pvc grey
Operating temperature: -10° / +60 °C

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
6.05
TPR FLEXIBLE HOSE FITTINGS
3D drawings are available on vuototecnica.net

Hex. C Fitting body Ring nut

Lock nut Seal ring Hex. H

RTPR FITTINGS
d A B C D E G H L Material Colour Weight
Item
Ø Ø g
RTPR 3/8” G3/8” 14.5 8.5 26 12.0 23.5 6 28 46.5 pvc grey 12
RTPR 1/2” G1/2” 14.5 9.0 28 15.5 26.5 7 33 50.0 pvc grey 18
RTPR 3/4” G3/4” 14.0 10.5 35 20.8 26.5 9 38 51.0 pvc grey 26
RTPR 1” G1” 16.0 9.0 41 26.5 32.5 10 44 57.5 pvc grey 36
Operating temperature: -10° / +60 °C

Hose adapter Ring nut

Fitting body Seal ring Hex. H

RTPR FITTINGS
d A B D E H L Material Weight
Item
Ø Ø g
RTPR 1” 1/4 G1” 1/4 11 6 34.5 28.5 52 45.5 nickel-plated brass 340
RTPR 1” 1/2 G1” 1/2 14 7 39.5 34.0 60 55.0 nickel-plated brass 530
RTPR 2” G2” 14 7 50.0 33.0 74 54.0 nickel-plated brass 596
Operating temperature: -20° / +60 °C

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
6.06
VACUUM PUMPS AND PUMP SETS

MEMBRANE VACUUM MINI PUMPS PG. 7.01 ÷ 7.02

MEMBRANE VACUUM MINI PUMPS, WITH DC MOTOR PG. 7.03 ÷ 7.04

3D drawings are available on vuototecnica.net

ROTARY VANE VACUUM PUMPS - GENERAL DESCRIPTION PG. 7.05 ÷ 7.06
VACUUM PUMPS VTL 2 and 4 PG. 7.07 ÷ 7.08
VACUUM PUMPS VTL 5 and 10 PG. 7.09 ÷ 7.10
VACUUM PUMPS VTLP 5 AND 10, WITH DISPOSABLE LUBRICATION PG. 7.11 ÷ 7.12
VACUUM PUMPS VTL 10/FG, 15/FG and 20/FG PG. 7.13-1 ÷ 7.14-1
VACUUM PUMPS VTLP 10/FG, 15/FG and 20/FG, WITH DISPOSABLE LUBRICATION PG. 7.15-1 ÷ 7.16-1
VACUUM PUMPS VTL 25/FG, 30/FG and 35/FG PG. 7.17 ÷ 7.18
VACUUM PUMPS VTLP 25/FG, 30/FG and 35/FG, WITH DISPOSABLE LUBRICATION PG. 7.19 ÷ 7.20
VACUUM PUMPS 40/G1, 50/G1 and 65/G1 PG. 7.21 ÷ 7.22
VACUUM PUMPS 75/G1, 90/G1 and 105/G1 PG. 7.23 ÷ 7.24
VACUUM PUMPS VTLP 40/G1, 50/G1 and 65/G1, WITH DISPOSABLE LUBRICATION PG. 7.25 ÷ 7.26
VACUUM PUMPS VTLP 75/G1, 90/G1 and 105/G1, WITH DISPOSABLE LUBRICATION PG. 7.27 ÷ 7.28
LUBRICATED ROTARY VANE VACUUM PUMPS, RVP SERIES - GENERAL DESCRIPTION PG. 7.29
OIL-BATH VACUUM PUMP RVP 15 PG. 7.30 ÷ 7.31
OIL-BATH VACUUM PUMP RVP 21 PG. 7.32 ÷ 7.33
OIL-BATH VACUUM PUMP RVP 40 PG. 7.34 ÷ 7.35
OIL-BATH VACUUM PUMP RVP 60 PG. 7.36 ÷ 7.37
OIL-BATH VACUUM PUMP RVP 100 PG. 7.38 ÷ 7.39
OIL-BATH VACUUM PUMPS RVP 160 and RVP 200 PG. 7.40 ÷ 7.41
OIL-BATH VACUUM PUMPS RVP 250 and RVP 300 PG. 7.42 ÷ 7.43
LUBRICATED VACUUM PUMP ACCESSORIES AND SPARE PARTS PG. 7.44 ÷ 7.47
DRY VACUUM PUMPS VTS 2 and 4 PG. 7.48 ÷ 7.49
DRY VACUUM PUMPS VTS 6 and 10 PG. 7.50 ÷ 7.51
DRY VACUUM PUMPS VTS 10/FG, 15/FG and 20/FG PG. 7.56 ÷ 7.57
DRY VACUUM PUMPS VTS 25/FG, 30/FG and 35/FG PG. 7.58 ÷ 7.59
DRY VACUUM PUMP ACCESSORIES AND SPARE PARTS PG. 7.60 ÷ 7.61
MINI PUMP SETS - GENERAL DESCRIPTION PG. 7.62
MINI PUMP SETS DO 06V ... and DO 10V ... WITH DRY VACUUM PUMPS PG. 7.63
MINI PUMP SETS DO 06V ... and DO 10V ... WITH LUBRICATED VACUUM PUMPS PG. 7.64
MINI PUMP SETS DO 20V ... PG. 7.65
HORIZONTAL PUMP SETS - GENERAL DESCRIPTION PG. 7.66
HORIZONTAL PUMP SETS DO 25V ... and DO 50V ... PG. 7.67
HORIZONTAL PUMP SETS DO 100V ... and DO 150V ... PG. 7.68
HORIZONTAL PUMP SETS DO 300V ... and DO 500V ... PG. 7.69
HORIZONTAL PUMP SETS DO 1000V ... PG. 7.70
HORIZONTAL SAFETY PUMP SETS – GENERAL DESCRIPTION PG. 7.71
HORIZONTAL SAFETY PUMP SETS DSO 300V ... and DSO 500V ... PG. 7.72
HORIZONTAL SAFETY PUMP SETS DSO 1000V ... PG. 7.73
VERTICAL PUMP SETS - GENERAL DESCRIPTION PG. 7.74
VERTICAL PUMP SETS DV 150V ... and DV 300V ... PG. 7.75
VERTICAL PUMP SETS DV 500V ... and DV 1000V ... PG. 7.76
VERTICAL SAFETY PUMP SETS – GENERAL DESCRIPTION PG. 7.77
VERTICAL SAFETY PUMP SETS DSV 150V ... and DSV 300V ... PG. 7.78 7
VERTICAL SAFETY PUMP SETS DSV 500V ... and DSV 1000V ... PG. 7.79
VERTICAL SAFETY PUMP SETS DSV 2000V ... PG. 7.80
SPECIAL PUMP SET PRODUCTS PG. 7.81 ÷ 7.82
SUPPORT FRAMES FOR TWO VACUUM PUMPS, WITH AND WITHOUT SWITCHGEAR PG. 7.83
SUPPORT FRAMES FOR THREE VACUUM PUMPS, WITH AND WITHOUT SWITCHGEAR PG. 7.84
SUPPORTS FOR SWITCHGEAR PG. 7.85
VACUUM PUMP AND PUMP SET MANIFOLDS PG. 7.86 ÷ 7.87
SWITCHGEAR FOR MINI PUMP SETS AND PUMP SETS WITH ONE PUMP PG. 7.88
SWITCHGEAR FOR PUMP SETS WITH TWO PUMPS PG. 7.89
SWITCHGEAR FOR SAFETY PUMP SETS WITH TWO PUMPS PG. 7.89
SWITCHGEAR FOR SAFETY PUMP SETS WITH THREE PUMPS PG. 7.90
SWITCHGEAR FOR SAFETY PUMP SETS WITH FOUR PUMPS PG. 7.90
ELECTRICAL SAFETY EQUIPMENT FOR SINGLE PUMP PG. 7.91
SWITCHGEAR EQUIPPED WITH TOUCH SCREEN OPERATOR PANEL AND
PLC FOR PUMP SETS AND SAFETY PUMP SETS WITH TWO OR MORE PUMP PG. 7.91-1 ÷ 7.92-1
VACUUM PUMP QUESTIONNAIRE PG. 7.93 ÷ 7.94
7
3D drawings are available on vuototecnica.net
MEMBRANE VACUUM MINI PUMPS

The small pumps described on this page are membrane-type.

They can be used both as vacuum pumps and compressors.
In the latter version they can supply compressed air 100% oil-free up
to a maximum 2 bar pressure.

3D drawings are available on vuototecnica.net

They are composed of:
- An air-cooled single-phase electric motor with protection class IP 00
(assembly execution).
- A pump body made of plastic corrosion-resistant material, complete
with fittings at both suction and blowing ports or, upon request, with
threaded connections.
- A Viton membrane, fixed to a connecting rod, resistant to wear and
corrosion.
- A connecting rod with incorporated long life bearing powered by an
eccentric balanced system fitted on the crankshaft.
- An aluminium support, for fastening the pump.
They are available in the versions with single and double head to be
used in series or in parallel.
Membrane vacuum mini pumps are very silent (≤ 50dB(A)), they have
reduced vibrations and can be installed in any position.
Lubrication-free, they require no maintenance.
Thanks to their minimal overall dimensions and reduced weight, they
are particularly indicated for being installed on portable equipment.
They are suited for a discontinuous and non-intense use.

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

t x V1
To calculate the emptying time of a volume of V 1, use the following formula: t 1=
6
V1 : Volume to be emptied ( l )
Curve relative to the flow rate (referring to a 1013 mbar pressure) t1 : time to be calculated (sec)
Curve relative to the emptying time of a 6-litre volume t : time obtained in the table (sec)

7.01
MEMBRANE VACUUM MINI PUMPS

H 35 M - H 35 M 110 60
3D drawings are available on vuototecnica.net

H 40 DM - H 40 DM 110 60

7 Item H35 M H35 M 110 60 H40 DM H40 DM 110 60

Frequency 50Hz 60Hz 50Hz 60Hz
Nominal flow rate:
Connection in series l / 1’ 8 9,5 8 9,5
Parallel connection l / 1’ = = 8+8 9,5 + 9,5
Final pressure:
Connection in series mbar abs. 200 60
Parallel connection mbar abs. = 200
Maximum pressure bar 2 2
Motor performance 1~ volt 230 VAC 110 VAC 230 VAC 110 VAC
Motor power 1~ watt 60 72 60 72
Rotation speed g/min -1 2800 3300 2800 3300
Noise level dB(A) ≤ 50 ≤ 50
Max weight Kg 1.3 1.6

Accessories and Parts H35 M H35 M 110 60 H40 DM H40 DM 110 60

Membrane item 00 H35M 15 00 H40DM 15
Cover with fittings item 00 H35M 16 00 H40DM 20
Cover without fittings item 00 H35MF 16 00 H40DMF 20
Add the letter F to the item for a mini pump supplied with G 1/8” threaded suction and blowing connections, without hose fittings. (Example: H40 DM F).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.02
MEMBRANE VACUUM MINI PUMPS,
WITH DC MOTOR
The mini pumps on this page are the same as described above,
with a DC motor rather than an AC.
The performances are also almost the same.

3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

t x V1
To calculate the emptying time of a volume of V 1, use the following formula: t 1=
6
V1 : Volume to be emptied ( l )
Curve relative to the flow rate (referring to a 1013 mbar pressure) t1 : time to be calculated (sec)
Curve regarding the emptying time of a 6-litre volume t : time obtained in the table (sec)

7.03
MEMBRANE VACUUM MINI PUMPS,
WITH DC MOTOR

H 35 M CC - H 35 M 12 CC
3D drawings are available on vuototecnica.net

H 40 DM CC - H 40 DM 12 CC

7
Item H35 M CC H35 M 12 CC H40 DM CC H40 DM 12 CC
Nominal flow rate:
Connection in series l / 1’ 8.5 8.5
Parallel connection l / 1’ = 8.5 + 8.5
Final pressure:
Connection in series mbar abs. 200 60
Parallel connection mbar abs. = 200
Maximum pressure bar 2 2
Motor performance volt 24 VDC 12 VDC 24 VDC 12 VDC
Motor power watt 12 22
Rotation speed g/min-1 3000 3000
Noise level dB(A) ≤ 50 ≤ 50
Max weight Kg 0.62 1.19

Accessories and Parts H35 M CC H35 M 12 CC H40 DM CC H40 DM 12 CC

Membrane item 00 H35M 15 00 H40DM 15
Cover with fittings item 00 H35M 16 00 H40DM 20
Cover without fittings item 00 H35MF 16 00 H40DMF 20
Note: Add the letter F to the item for a mini pump supplied with G 1/8” threaded suction and blowing connections, without hose fittings. (Example: H35 M F CC).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.04
ROTARY VANE VACUUM PUMPS - GENERAL DESCRIPTION

Working principle
The rotor rotates eccentrically inside a stator and it has grooves in
which the vanes move freely and are pushed against the stator inside

3D drawings are available on vuototecnica.net

wall due to the centrifugal force, thus creating as many chambers as
the number of vanes. During rotation, the volume of these chambers
varies according to their position with respect to the eccentric axis.
The chamber volume increase makes the air inside of them expand,
thus creating vacuum (suction phase); the volume reduction, on the
1.
other hand, generates air compression (exhaust or delivery phase).
The internal design is the same for both rotating compressors and
vacuum pumps. We have created two different sucked air conveying
principles for our pumps.
Figure 1 illustrates a system with three rotary blades and discharge
valve (1); this system is mainly used in the high vacuum field.
Figure 2 illustrates a system with six rotary blades and therefore with
several chambers, which is mainly used in the rough vacuum field.
2.

Rotor housing
In smaller and more compact pumps, the rotor is cantilevered on the
crankshaft extension (fig.1), while in the versions with high installed 1.
power or with frequent start-ups, the rotor is supported by bearings on
both sides (fig. 2).
In this case, the pump and the electric motor are two independent units
and the two shafts are coupled together by an elastic transmission joint.

2.
Lubrication system
The main lubrication systems used by us are vacuum with oil
recirculation or waste oil for vacuum pumps in the VTL series and an oil
bath for pumps in the RVP series.
In oil recirculation lubrication (fig.1), the oil sucked into the working
chamber through the adjustable oilers that dose the flow is discharged
together with the air sucked into the recovery tank and, through a special 7
filter contained in it, is separated from the air and put back into the cycle.
With disposable oil lubrication (fig.2), the lubrication oil is contained in
a special transparent container, controlled by a magnetic level switch,
and follows the same route previously described but is collected in the
recovery tank without being put back into the cycle. This lubrication
system is recommended when there are water condensates, solvent
vapours or anything else that can pollute the oil in the intake air.
With oil-bath lubrication (fig.3), the oil is sucked into the working
chamber directly from the recovery tank through calibrated pipes that
measure the quantity and is held and separated from the air during
discharge by special dehydrating microfibre cartridges, contained in the 1. 2.
tank itself.
In this lubrication system, the quantity of oil in circulation is significantly
higher than that of the two systems described above. This leads to a
better seal between the stator and the rotor and lower friction between
the rotating and fixed parts, with a resulting increase in the degree of
vacuum, less heating and less noise.

7.05
ROTARY VANE VACUUM PUMPS - GENERAL DESCRIPTION

Dry vacuum pumps

The particular shape of the working chamber and the special graphite with which the
blades and closing flanges are made allow these pumps to work without any need for
3D drawings are available on vuototecnica.net

lubrication.
Use of these pumps is not recommended when the fluid to be suctioned contains
vapours or water or oil condensation.

Cooling
The pump cooling system we use is the surface air type. The heat developed by the
vacuum pump is dispersed from the external, specially finned surface by the fan of
the electric motor on smaller pumps and by a radial fan keyed on the pump shaft on
larger pumps. Pumps with capacities from 100 m3/h upwards are also equipped with
a serpentine radiator (1). In this case, the lubricating oil, passing through the radiator
before entering the working chamber, is cooled by the radial fan, which sucks the cooling
air through the radiator itself, allowing a further reduction of the heat developed by the
pump.

1. 2. 3.

Materials used
The stator and the flanges of the pumps are made of spheroidal cast iron, the
transmission shaft and the rotor are made of carbon steel, while the vanes are in carbon
fibre or glass for lubricated pumps and in graphite for dry pumps.

Electric motors
All vacuum pumps with flow rate up to 21 m3/h can be supplied either with three-phase
or single-phase electric motors; for those with higher flow rates, only three-phase.
All the pumps are equipped as standard with multi-voltage electric motors, according
7
to EC regulations. Upon request, they can be supplied with UL-CSA compliant motors or
with special voltages and frequencies.
The pumps are driven by an electric motor, in compliance with IEC International
Standard 60034 requirements for rotating machines and European Directives for Low
Voltage (LV) 2006/95/EC, for Electromagnetic Compatibility (EMC) 2004/108/EC, for
the limitation of use of hazardous substances RoHS 2011/65/EC and Machine Directive
2006/42/EC for CE marking.
With the exception of electric motors with power lower than 0.75 KW, the efficiency
class corresponds to IE3 = Premium Efficiency, with protection degree IP 55, Tolerance
of nominal Voltage ± 10% and Class of Insulation F.

Certifications
The design and construction of our vacuum pumps comply with European safety
directives. The "CE" mark is in fact reported along with the technical characteristics of
the pumps on all the identification plates and the instructions for use and maintenance
that accompany them are always provided with a Declaration of Compliance with
Machinery Directive 2006/42/EC and subsequent changes.

7.06
VACUUM PUMPS VTL 2 and 4

These small vacuum pumps have a suction flow rate of 2 and 4 m3/h.
They feature a wick lubrication with oil recirculation, while the rotor,
which is cantilevered-fitted on the motor shaft, allows reducing the
overall dimensions to the minimum.

3D drawings are available on vuototecnica.net

The motor and the pump are cooled by the motor fan (surface
cooling).
The pumps are equipped with a small tank in line with the pump,
which contains the lubrication oil as well as a separator filter to
prevent oil mists and to reduce noise.
We strongly recommend installing a check valve and a filter on the
suction inlet.
Pumps VTL 2 and 4 can also be supplied with single-phase electric
motor.

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

t x V1
To calculate the emptying time of a volume of V 1, use the following formula: t1=
100
Curve relative to the flow rate (referring to the suction pressure) V1 : Volume to be emptied ( l )
Curve relative to the flow rate (referring to a 1013 mbar pressure) t1 : time to be calculated (sec)
Curve regarding the emptying time of a 100-litre volume t : time obtained in the table (sec)

7.07
VACUUM PUMPS VTL 2 and 4
3D drawings are available on vuototecnica.net

Item VTL 2 VTL 4

Frequency 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 2.0 2.4 4.0 4.8
Final pressure mbar abs. 150 150
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10%
Motor power 3~ 0.12 0.15 0.18 0.21
Kw 1~ 0.12 0.15 0.18 0.21
Motor protection IP 55 55
Rotation speed g/min-1 2700 3245 2760 3300
Motor shape Special Special
Motor size 56 63
Noise level dB(A) 62 65 62 65
Max weight 3~ 5.7 7.3
Kg 1~ 6.0 7.5
A 260 285
B 145 160
7 C 126 132
D 62 66
E 71 81
F 127 139
G Ø 6.5 7.5
H 72 81
I 90 100
L 43 48
M 12 12
N 76 86
R Ø gas G1/4” G3/8”

Accessories and Parts VTL 2 VTL 4

Oil charge L 0.05 0.05
Lubricating oil type ISO 32 ISO 32
4 vanes item 00 VTL 02 10 00 VTL 04 10
Sealing kit item 00 KIT VTL 02 00 KIT VTL 04
Check valve item 10 01 15 10 02 15
Suction filter item FB 5 FB 10/FC 10
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTL 2 M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.08
VACUUM PUMPS VTL 5 and 10

These vacuum pumps have a suction flow rate of 5 and 10 m3.

The vacuum lubrication with oil recirculation can be adjusted via an
oiler located in correspondence of the suction inlet.
The rotor is cantilevered-fitted on the motor shaft and, as a result, the

3D drawings are available on vuototecnica.net

overall dimensions are reduced.
The motor and the pump are cooled by the motor fan (surface
cooling).
An oil recovery tank is installed on the pump exhaust. This tank
contains a separator filter that prevents oil mists and reduces noise.
We strongly recommend installing a check valve and a filter on the
suction inlet.
Pumps VTL 5 and 10 can also be supplied with a single-phase electric
motor.

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

7.09
VACUUM PUMPS VTL 5 and 10
3D drawings are available on vuototecnica.net

Item VTL 5 VTL 10

Frequency 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 5.0 6.0 10.0 12.0
Final pressure mbar abs. 80 80
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10%
Motor power 3~ 0.25 0.30 0.37 0.40
Kw 1~ 0.25 0.30 0.37 0.40
Motor protection IP 55 55
Rotation speed g/min-1 1450 1680 1450 1680
Motor shape Special Special
Motor size 71 71
Noise level dB(A) 62 64 62 64
Max weight 3~ 14.5 20.5
Kg 1~ 15.0 21.0
7 A 260 310
B 245 262
C 245 245
D 52 70
F 53 85
H 122 122
L 45 45
M 85 102
N 27 52
R Ø gas G3/8” G1/2”

Accessories and Parts VTL 5 VTL 10

Oil charge L 0.25 0.40
Lubricating oil type ISO 32 ISO 100
6 vanes item 00 VTL 05 10 00 VTL 10 10
Sealing kit item 00 KIT VTL 05 00 KIT VTL 10
Check valve item 10 02 10 10 03 10
Suction filter item FB 10/FC 10 FB 20/FC 20
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTL 5 M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.10
VACUUM PUMPS VTLP 5 and 10
WITH DISPOSABLE LUBRICATION

3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

7.11
VACUUM PUMPS VTLP 5 and 10
WITH DISPOSABLE LUBRICATION
3D drawings are available on vuototecnica.net

Item VTLP 5 VTLP 10

Frequency 50Hz 60Hz 50Hz 60Hz

Flow rate m3/h 5.0 6.0 10.0 12.0
Final pressure mbar abs. 80 80
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10%
Motor power 3~ 0.25 0.30 0.37 0.40
Kw 1~ 0.25 0.30 0.37 0.40
Motor protection IP 55 55
Rotation speed g/min-1 1450 1680 1450 1680
Motor shape Special Special
Motor size 71 71
Noise level dB(A) 62 64 62 64
Max weight 3~ 15.6 21.6
7 Kg 1~ 16.1 22.1
A 260 310
B 245 262
D 52 70
F 53 85
M 85 102
N 27 52
R Ø gas G3/8” G1/2”

Accessories and Parts VTLP 5 VTLP 10

Oil charge L 1.8 1.8
Lubricating oil type ISO 32 ISO 100
6 vanes item 00 VTL 05 10 00 VTL 10 10
Sealing kit item 00 KIT VTL 05 00 KIT VTL 10
Check valve item 10 02 10 10 03 10
Suction filter item FB 10/FC 10 FB 20/FC 20
Oil level switch item 00 LP VTL 99 00 LP VTL 99
Oil filter item 00 LP VTL 40 00 LP VTL 40
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTLP 5 M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.12
VACUUM PUMPS VTL 10/FG, 15/FG and 20/FG

These vacuum pumps have a suction flow rate of 10, 15 and 20 m3/h.
The vacuum lubrication with oil recirculation is adjusted via two oilers
located in correspondence of the support bearings.
The rotor is cantilevered-fitted on the motor shaft and supported by

3D drawings are available on vuototecnica.net

independent bearings housed in the two pump flanges.
The pump and the electric motor are, therefore, two independent units
and fixed onto a special support and connected to each other via an
elastic transmission joint.
All this allows using standard electric motors, in the shapes and sizes
indicated in the table.
The pump is surface cooled. Heat is dispersed from the outer surface,
suitably finned, by means of a radial fan placed between motor and
pump.
An oil recovery tank is installed on the pump exhaust. This tank
contains a separator filter that prevents oil mists and reduces noise.
We strongly recommend installing a check valve and a filter on the
suction inlet.
Also this range of pumps can be supplied with single-phase electric
motors.

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.13 -1
VACUUM PUMPS VTL 10/FG, 15/FG and 20/FG
3D drawings are available on vuototecnica.net

Item VTL 10/FG VTL 15/FG VTL 20/FG

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 10.0 12.0 15.0 18.0 20.0 24.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10% 230±10%
Motor power 3~ 0.55 0.66 0.55 0.66 0.55 0.66
Kw 1~ 0.55 0.66 0.55 0.66 0.55 0.66
Motor protection IP 55 55 55
Rotation speed g/min-1 1450 1680 1450 1680 1450 1680
Motor shape Special Special Special
Motor size 80 80 80
Noise level dB(A) 71 73 74 76 80 82
Max weight 3~ 24.0 28.0 31.0
Kg 1~ 24.5 28.5 31.5
A 430 450 470
7 B 300 300 300
C 270 270 285
D 65 65 65
E 340 340 340
F 25 45 65
H 133 133 133
L 55 55 55
M 115 115 155
N 58 68 78
R Ø gas G1/2” G1/2” G1/2”

Accessories and Parts VTL 10/FG VTL 15/FG VTL 20/FG

Oil charge L 0.4 0.5 0.65
Lubricating oil type ISO 100 ISO 100 ISO 100
6 vanes item 00 VTL 10FG 10 00 VTL 15FG 10 00 VTL 20FG 10
Sealing kit item 00 KIT VTL 10FG 00 KIT VTL 15FG 00 KIT VTL 20FG
Check valve item 10 03 10 10 03 10 10 03 10
Suction filter item FB 20/FC 20 FB 20/FC 20 FB 20/FC 20
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTL 10/FG M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.14 -1
VACUUM PUMPS VTLP 10/FG, 15/FG and 20/FG,
WITH DISPOSABLE LUBRICATION
These vacuum pumps have a suction flow rate of 10, 15 and 20 m3/h.
The vacuum with disposable oil lubrication is adjusted via two oilers located in
correspondence of the support bearings.
The rotor is cantilevered-fitted on the motor shaft and supported by independent

3D drawings are available on vuototecnica.net

bearings housed in the two pump flanges.
The pump and the electric motor are, therefore, two independent units and fixed onto a
special support and connected to each other via an elastic transmission joint.
All this allows using standard electric motors, in the shapes and sizes indicated in the table.
The pump is surface cooled. Heat is dispersed from the outer surface, suitably finned, by
means of a radial fan placed between motor and pump.
An oil recovery tank is installed on the pump exhaust. This tank contains a separator
filter that prevents oil mists and reduces noise.
A safety valve is also installed on the tank for the automatic drainage of the
exhaust oil when not regularly drained.
The lubrication oil is contained in a special transparent container, fixed to the
pump via its support, and controlled by a magnetic level switch.
In pumps with disposable lubrication, the oil is sucked in the pump through an
adjustable drip oilers and drained together with the sucked air in the recovery
tank, without being put in circulation again. These pumps are necessary when
the air to be sucked contains water condensation, solvent vapours or anything
else that could affect oil properties.
We strongly recommend installing a check valve and a filter on the suction inlet.
Also this range of pumps can be supplied with single-phase electric motors.

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time 7

Vacuum mbar Vacuum mbar Vacuum mbar

7.15 -1
VACUUM PUMPS VTLP 10/FG, 15/FG and 20/FG,
WITH DISPOSABLE LUBRICATION
3D drawings are available on vuototecnica.net

Item VTLP 10/FG VTLP 15/FG VTLP 20/FG

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 10.0 12.0 15.0 18.0 20.0 24.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10% 230±10%
Motor power 3~ 0.55 0.66 0.55 0.66 0.55 0.66
Kw 1~ 0.55 0.66 0.55 0.66 0.55 0.66
Motor protection IP 55 55 55
Rotation speed g/min-1 1450 1680 1450 1680 1450 1680
Motor shape Special Special Special
Motor size 80 80 80
Noise level dB(A) 71 73 74 76 80 82
7 Max weight 3~ 24.0 28.0 31.0
Kg 1~ 24.5 28.5 31.5
A 430 450 470
B 300 300 300
C 445 445 460
F 25 45 65
M 115 115 155
N 58 68 78

Accessories and Parts VTLP 10/FG VTLP 15/FG VTLP 20/FG

Oil charge L 1.8 1.8 1.8
Lubricating oil type ISO 100 ISO 100 ISO 100
6 vanes item 00 VTL 10FG 10 00 VTL 15FG 10 00 VTL 20FG 10
Sealing kit item 00 KIT VTL 10FG 00 KIT VTL 15FG 00 KIT VTL 20FG
Check valve item 10 03 10 10 03 10 10 03 10
Suction filter item FB 20/FC 20 FB 20/FC 20 FB 20/FC 20
Oil level switch item 00 LP VTL 99 00 LP VTL 99 00 LP VTL 99
Oil filter item 00 LP VTL 40 00 LP VTL 40 00 LP VTL 40
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTLP 10/FG M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.16 -1
VACUUM PUMPS VTL 25/FG, 30/FG and 35/FG

These vacuum pumps have a suction flow rate of 25, 30 and 35 m3/h.
The vacuum lubrication with oil recirculation is adjusted via two oilers
located in correspondence of the support bearings.
The rotor is cantilevered-fitted on the motor shaft and supported by

3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.17
VACUUM PUMPS VTL 25/FG, 30/FG and 35/FG
3D drawings are available on vuototecnica.net

Item VTL 25/FG VTL 30/FG VTL 35/FG

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 25.0 30.0 30.0 36.0 35.0 42.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10% 230±10%
Motor power 3~ 0.75 0.90 0.75 0.90 1.10 1.35
Kw 1~ 0.75 0.75 1.10
Motor protection IP 55 55 55
Rotation speed g/min-1 1410 1640 1410 1640 1435 1745
Motor shape B14 B14 B14
7 Motor size 80 80 80
Noise level dB(A) 64 66 65 67 65 67
Max weight 3~ 31.0 35.0 37.0
Kg 1~ 31.5 35.5 37.5
A 470 490 510
C 280 280 280
F 20 40 60
H 133 133 133
N 73 83 93
R Ø gas G3/4” G3/4” G3/4”

Accessories and Parts VTL 25/FG VTL 30/FG VTL 35/FG

Oil charge L 0.65 0.85 0.85
Lubricating oil type ISO 100 ISO 100 ISO 100
6 vanes item 00 VTL 25FG 10 00 VTL 30FG 10 00 VTL 35FG 10
Sealing kit item 00 KIT VTL 25FG 00 KIT VTL 30FG 00 KIT VTL 35FG
Check valve item 10 04 10 10 04 10 10 04 10
Suction filter item FB 28/FC 25 FB 28/FC 25 FB 28/FC 25
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTL 25/FG M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.18
VACUUM PUMPS VTLP 25/FG, 30/FG and 35/FG
WITH DISPOSABLE LUBRICATION
These vacuum pumps have a suction flow rate of 25, 30 and 35 m3/h.
The vacuum with disposable oil lubrication is adjusted via two oilers located in correspondence
of the support bearings.
The rotor is cantilevered-fitted on the motor shaft and supported by independent bearings

3D drawings are available on vuototecnica.net

housed in the two pump flanges.
The pump and the electric motor are, therefore, two independent units and fixed onto a special
support and connected to each other via an elastic transmission joint.
All this allows using standard electric motors, in the shapes and sizes indicated in the table.
The pump is surface cooled. Heat is dispersed from the outer surface, suitably finned, by means
of a radial fan placed between motor and pump.
An oil recovery tank is installed on the pump exhaust. This tank contains a separator filter that
prevents oil mists and reduces noise.
A safety valve is also installed on the tank for the automatic drainage of the exhaust oil when
not regularly drained.
The lubrication oil is contained in a special transparent container, fixed to the pump via
its support, and controlled by a magnetic level switch.
In pumps with disposable lubrication, the oil is sucked in the pump through an
adjustable drip oilers and drained together with the sucked air in the recovery tank,
without being put in circulation again. These pumps are necessary when the air to be
sucked contains water condensation, solvent vapours or anything else that could affect
oil properties.
We strongly recommend installing a check valve and a filter on the suction inlet.
Also this range of pumps can be supplied with single-phase electric motors.

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time 7

Vacuum mbar Vacuum mbar Vacuum mbar

7.19
VACUUM PUMPS VTLP 25/FG, 30/FG and 35/FG
WITH DISPOSABLE LUBRICATION
3D drawings are available on vuototecnica.net

Item VTLP 25/FG VTLP 30/FG VTLP 35/FG

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 25.0 30.0 30.0 36.0 35.0 42.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10% 230±10%
Motor power 3~ 0.75 0.90 0.75 0.90 1.10 1.35
Kw 1~ 0.75 0.75 1.10
Motor protection IP 55 55 55
Rotation speed g/min-1 1410 1640 1410 1640 1435 1745
Motor shape B14 B14 B14
Motor size 80 80 80
7 Noise level dB(A) 64 66 65 67 65 67
Max weight 3~ 32.0 36.0 38.0
Kg 1~ 32.5 36.5 38.5
A 470 490 510
F 20 40 60
H 133 133 133
N 73 83 93
R Ø gas G3/4” G3/4” G3/4”

Accessories and Parts VTLP 25/FG VTLP 30/FG VTLP 35/FG

Oil charge L 1.8 1.8 1.8
Lubricating oil type ISO 100 ISO 100 ISO 100
6 vanes item 00 VTL 25FG 10 00 VTL 30FG 10 00 VTL 35FG 10
Sealing kit item 00 KIT VTL 25FG 00 KIT VTL 30FG 00 KIT VTL 35FG
Check valve item 10 04 10 10 04 10 10 04 10
Suction filter item FB 28/FC 25 FB 28/FC 25 FB 28/FC 25
Oil level switch item 00 LP VTL 99 00 LP VTL 99 00 LP VTL 99
Oil filter item 00 LP VTL 40 00 LP VTL 40 00 LP VTL 40
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTLP 25/FG M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.20
VACUUM PUMPS VTL 40/G1 - 105/G1

These vacuum pumps have a suction flow rate of 40, 50, 65, 75, 90
and 105 m3/h.
The vacuum lubrication with oil recirculation is adjusted via two oilers
located in correspondence of the support bearings.

3D drawings are available on vuototecnica.net

The rotor is cantilevered-fitted on the motor shaft and supported by
independent bearings housed in the two pump flanges.
The pump and the electric motor are, therefore, two independent
units and fixed onto a special support and connected to each other via
an elastic transmission joint.
All this allows using standard electric motors, in the shapes and sizes
indicated in the table.
The pump is surface cooled. Heat is dispersed from the outer surface,
suitably finned, by means of a radial fan placed between motor and
pump.
An oil recovery tank is installed on the pump exhaust. This tank
contains a separator filter that prevents oil mists and reduces noise.
A check valve and a filter must be installed on the suction inlet.
These pumps are supplied with three-phase electric motors only.

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.21
VACUUM PUMPS VTL 40/G1, 50/G1 and 65/G1
3D drawings are available on vuototecnica.net

Item VTL 40/G1 VTL 50/G1 VTL 65/G1

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 40.0 48.0 50.0 60.0 65.0 78.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ volt 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Motor power 3~ Kw 1.10 1.35 1.50 1.80 1.50 1.80
Motor protection IP 55 55 55
Rotation speed g/min-1 1440 1750 1440 1750 1440 1750
Motor shape B5 B5 B5
Motor size 90 90 90
Noise level dB(A) 68 70 68 70 70 72
7 Max weight 3~ kg 51.0 54.0 71.0
A 520 560 580
B 365 365 365
C 350 350 350
D 60 115 120
F 45 30 45
H 186 186 186
M 125 125 125
N 70 80 80
R Ø gas G1” G1” G1”

Accessories and Parts VTL 40/G1 VTL 50/G1 VTL 65/G1

Oil charge L 0.85 1.00 1.00
Lubricating oil type ISO 100 ISO 100 ISO 100
6 vanes item 00 VTL 40G1 10 00 VTL 50G1 10 00 VTL 65G1 10
Sealing kit item 00 KIT VTL 40G1 00 KIT VTL 50G1 00 KIT VTL 65 G1
Check valve item 10 05 10 10 05 10 10 05 10
Suction filter item FB 30/FC 30 FB 30/FC 30 FB 30/FC 30
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.22
VACUUM PUMPS VTL 75/G1, 90/G1 and 105/G1

3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.23
VACUUM PUMPS VTL 75/G1, 90/G1 and 105/G1
3D drawings are available on vuototecnica.net

Item VTL 75/G1 VTL 90/G1 VTL 105/G1

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 75.0 90.0 90.0 108.0 105.0 126.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ volt 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Motor power 3~ Kw 2.20 2.70 3.00 3.60 3.00 3.60
Motor protection IP 55 55 55
Rotation speed g/min-1 1450 1755 1440 1700 1440 1700
Motor shape B5 B5 B5
Motor size 100 100 100
Noise level dB(A) 70 72 71 73 72 74
7 Max weight 3~ kg 76.5 84.0 97.6
A 640 660 690
B 385 400 400
C 400 400 445
F 62 82 112
H 186 186 186
M 145 150 160
N 80 92 122
R Ø gas G1”1/4 G1”1/4 G1”1/2

Accessories and Parts VTL 75/G1 VTL 90/G1 VTL 105/G1

Oil charge L 2.0 2.6 2.6
Lubricating oil type ISO 150 ISO 150 ISO 150
Deoiling cartridge item 00 VTL 75G1 29 00 VTL 90G1 29 00 VTL 105G1 29
6 vanes item 00 VTL 75G1 10 00 VTL 90G1 10 00 VTL 105G1 10
Sealing kit item 00 KIT VTL 75G1 00 KIT VTL 90G1 00 KIT VTL 105G1
Check valve item 10 06 10 10 06 10 10 07 10
Exhaust filter item FB 40/FC 40 FB 40/FC 40 FB 50/FC 50
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.24
VACUUM PUMPS VTLP 40/G1 - 105/G1
WITH DISPOSABLE LUBRICATION
These vacuum pumps have a suction flow rate of 40, 50, 65, 75, 90 and 105 m3/h.
The vacuum with disposable oil lubrication is adjusted via two oilers located in
correspondence of the support bearings.
The rotor is cantilevered-fitted on the motor shaft and supported by independent

3D drawings are available on vuototecnica.net

bearings housed in the two pump flanges.
The pump and the electric motor are, therefore, two independent units and fixed onto a
special support and connected to each other via an elastic transmission joint.
All this allows using standard electric motors, in the shapes and sizes indicated in the
table.
The pump is surface cooled. Heat is dispersed from the outer surface, suitably finned, by
means of a radial fan placed between motor and pump.
An oil recovery tank is installed on the pump exhaust. This tank contains a separator
filter that prevents oil mists and reduces noise.
A safety valve is also installed on the tank for the automatic drainage of the exhaust
oil when not regularly drained.
The lubrication oil is contained in a special transparent container, fixed to the pump
via its support, and controlled by a magnetic level switch.
In pumps with disposable lubrication, the oil is sucked in the pump through an
adjustable drip oilers and drained together with the sucked air in the recovery tank,
without being put in circulation again. These pumps are necessary when the air to be
sucked contains water condensation, solvent vapours or anything else that could affect
oil properties.
A check valve and a filter must be installed on the pump suction inlet.
These pumps are supplied with three-phase electric motors only.

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time 7

Vacuum mbar Vacuum mbar Vacuum mbar

7.25
VACUUM PUMPS VTLP 40/G1, 50/G1 and 65/G1
WITH DISPOSABLE LUBRICATION
3D drawings are available on vuototecnica.net

Item VTLP 40/G1 VTLP 50/G1 VTLP 65/G1

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 40.0 48.0 50.0 60.0 65.0 78.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ volt 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Motor power 3~ Kw 1.10 1.35 1.50 1.80 1.50 1.80
Motor protection IP 55 55 55
Rotation speed g/min-1 1440 1750 1440 1750 1440 1750
Motor shape B5 B5 B5
Motor size 90 90 90
7 Noise level dB(A) 68 70 68 70 70 72
Max weight 3~ kg 52.5 55.1 72.1
A 520 560 580
D 60 115 120
F 45 30 45
M 125 125 125
N 70 80 80
R Ø gas G1” G1” G1”

Accessories and Parts VTLP 40/G1 VTLP 50/G1 VTLP 65/G1

Oil charge L 1.8 1.8 1.8
Lubricating oil type ISO 100 ISO 100 ISO 100
6 vanes item 00 VTL 40G1 10 00 VTL 50G1 10 00 VTL 65G1 10
Sealing kit item 00 KIT VTL 40G1 00 KIT VTL 50G1 00 KIT VTL 65G1
Check valve item 10 05 10 10 05 10 10 05 10
Suction filter item FB 30/FC 30 FB 30/FC 30 FB 30/FC 30
Oil level switch item 00 LP VTL 99 00 LP VTL 99 00 LP VTL 99
Oil filter item 00 LP VTL 40 00 LP VTL 40 00 LP VTL 40
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.26
VACUUM PUMPS VTLP 75/G1, 90/G1 and 105/G1
WITH DISPOSABLE LUBRICATION

3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.27
VACUUM PUMPS VTLP 75/G1, 90/G1 and 105/G1
WITH DISPOSABLE LUBRICATION
3D drawings are available on vuototecnica.net

Item VTLP 75/G1 VTLP 90/G1 VTLP 105/G1

Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 75.0 90.0 90.0 108.0 105.0 126.0
Final pressure mbar abs. 50 50 50
Motor performance 3~ volt 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Motor power 3~ Kw 2.20 2.70 3.00 3.60 3.00 3.60
Motor protection IP 55 55 55
Rotation speed g/min-1 1450 1735 1440 1700 1440 1700
Motor shape B5 B5 B5
Motor size 100 100 100
Noise level dB(A) 70 72 71 73 72 74
Max weight 3~ kg 78.3 85.8 99.4
7 A 640 660 690
B 415 430 430
C 575 575 620
F 62 82 112
M 145 150 160
N 80 92 122
R Ø gas G1”1/4 G1”1/4 G1”1/2

Accessories and Parts VTLP 75/G1 VTLP 90/G1 VTLP 105/G1

Oil charge L 3.8 3.8 3.8
Lubricating oil type ISO 150 ISO 150 ISO 150
Deoiling cartridge item 00 VTL 75G1 29 00 VTL 90G1 29 00 VTL 105G1 29
6 vanes item 00 VTL 75G1 10 00 VTL 90 G110 00 VTL 105 G110
Sealing kit item 00 KIT VTL 75G1 00 KIT VTL 90G1 00 KIT VTL 105G1
Check valve item 10 06 10 10 06 10 10 07 10
Suction filter item FB 40/FC 40 FB 40/FC 40 FB 50/FC 50
Oil level switch item 00 LP VTL 99 00 LP VTL 99 00 LP VTL 99
Oil filter item 00 LP VTL 40 00 LP VTL 40 00 LP VTL 40
Adjustable drip oiler item 00 VTL 00 11 00 VTL 00 11 00 VTL 00 11

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.28
LUBRICATED ROTARY VANE VACUUM PUMPS, RVP SERIES - GENERAL DESCRIPTION

The pumps in this new series are single-stage, rotary vane and with oil-bath lubrication
with recycling. The implementation of cutting edge construction techniques and the use
of hi-tech, latest generation materials has allowed for the achievement of high standards
of quality, performance, duration and low cost of use. The resulting technical features

3D drawings are available on vuototecnica.net

include:
- High pumping speed in the field of absolute pressure between 850 and 0.5 mbar
- Extremely low noise output
- Low operating temperatures
- No pollution
- Low maintenance
The pumps are driven by an electric motor, coupled by means of an elastic transmission
joint (not including RVP 15), in compliance with IEC International Standard 60034
requirements for rotating machines and European Directives for Low Voltage (LV)
2006/95/EC, for Electromagnetic Compatibility (EMC) 2004/108/EC, for the limitation of
use of hazardous substances RoHS 2011/65/CE and Machine Directive 2006/42/EC for
CE marking.
With the exception of electric motors with power lower than 0.75 KW, the efficiency class
corresponds to IE3 = Premium Efficiency, with protection degree IP 55, Tolerance of
nominal Voltage ± 10% and Class of Insulation F.
A centrifuge fan fitted on the pump shaft ensures a suitable air flow for optimal pump
body and radiator cooling (forced surface cooling).
A capacious oil recovery tank located on the pump outlet and equipped with microfibre
deoiling cartridges has the function of smoke filtering system and silencer. A special
built-in ball cock valve allows for the recovery of oil retained by cartridges. The oil filter,
except mod. RVP 15 and 21 pumps, are installed as standard on all.
The oil contained in the system lubricates, cools and seals rotating and fixed pump
parts. The check valve on the suction line is an integral part of the pump and is standard
while a filter suitable for trapping any suctioned impurities can be supplied upon request.
All pumps except mod. RVP 15 and RVP 21, are supplied standard with a gas ballast
valve, which permits high water vapour compatibility. Instead, for mod. RVP 21, the
ballast valve can only be installed upon request.
The above described product devices combined with strong, compact construction
make RVP series vacuum pumps especially suitable for continuous and heavy-duty use.

7.29
OIL-BATH VACUUM PUMP RVP 15
3D drawings are available on vuototecnica.net

RVP 15
Flow rate Time
RVP 15

Vacuum mbar

Flow rate Time

RVP 15
RVP 15

Vacuum mbar

7.30
OIL-BATH VACUUM PUMP RVP 15

3D drawings are available on vuototecnica.net

Item RVP 15
Frequency 50 Hz 60 Hz
Flow rate m3/h 15.0 18.0
Final pressure mbar abs. 2
Motor performance 3~ 230/400 ± 10% 275/480 ± 10%
Volt 1~ 230 ± 10% 275 ± 10%
Motor power 3~ 0.55 0.66
Kw 1~ 0.55 0.66
Motor protection IP 55
Rotation speed g/min-1 2700 3240
Motor shape B14
Motor size 90
Noise level dB(A) 63 64
Max weight 3~ 15.0
Kg 1~ 15.5
A 308
B 221
C 200
D 53
E 150
F 105 7
G Ø M8
H 195
I 112
L 89
M 19
N 54
O 58
P 82
R Ø gas G1/2”

Accessories and Parts RVP 15

Oil charge L 0.50
Lubricating oil type VT OIL 68
Deoiling cartridge item 00 RVP 15 05
3 vanes item 00 RVP 15 04
Sealing kit item 00 RVP 15 06
Check valve item 00 RVP 15 03
Suction filter item FC 20
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: RVP 15 M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.31
OIL-BATH VACUUM PUMP RVP 21
3D drawings are available on vuototecnica.net

RVP 21 RVP 21 Z

Flow rate Time

RVP 21

Vacuum mbar

Flow rate Time

RVP 21

Vacuum mbar

7.32
OIL-BATH VACUUM PUMP RVP 21

3D drawings are available on vuototecnica.net

Item RVP 21
Frequency 50 Hz 60 Hz
Flow rate m3/h 21.0 25.0
Final pressure mbar abs. 1
Motor performance 3~ 230/400 ± 10% 275/480 ± 10%
Volt 1~ 230 ± 10% 275 ± 10%
Motor power 3~ 0.75 0.90
Kw 1~ 0.75 0.90
Motor protection IP 55
Rotation speed g/min-1 2700 3240
Motor shape B14
Motor size 90
Noise level dB(A) 64 65
Max weight 3~ 18.5
Kg 1~ 19.0
A 421
B 232
C 225
D 63
E 230
F 128
G Ø M8 7
H 173
I 131
L 28
M 73
N 62
O 41
R Ø gas G1/2”

Accessories and Parts RVP 21

Oil charge L 0.50
Lubricating oil type VT OIL 68
Deoiling cartridge item 00 RVP 21 05
3 vanes item 00 RVP 21 04
Sealing kit item 00 RVP 21 06
Check valve item 00 RVP 21 03
Suction filter item FC 20
Ballast valve item 00 RVP 21 17
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: RVP 21 M).
Add the letter Z to the item for a pump supplied with a ballast valve (Example: RVP 21 Z).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.33
OIL-BATH VACUUM PUMP RVP 40
3D drawings are available on vuototecnica.net

Flow rate Time

RVP 40

Vacuum mbar

Flow rate Time

RVP 40

Vacuum mbar

7.34
OIL-BATH VACUUM PUMP RVP 40

3D drawings are available on vuototecnica.net

Item RVP 40
Frequency 50 Hz 60 Hz
Flow rate m3/h 40.0 48.0
Final pressure mbar abs. 0.5
H2O steam quantity
permitted Kg/h 0,7
Motor performance 3~ Volt 230/400 ± 10% 275/480 ± 10%
Motor power 3~ Kw 1.10 1.35
Motor protection IP 55
Rotation speed g/min-1 1450 1740
Motor shape B14
Motor size 100
Noise level dB(A) 64 65
Max weight Kg 49.0
A 645
B 286
C 266
D 157
E 335
F 225
G Ø M8
H 260
I 240 7
L 15
M 31
N 157
O 115
P 80
Q 66
R Ø gas G1”1/4

Accessories and Parts RVP 40

Oil charge L 1.25
Lubricating oil type VT OIL 100
Oil filter item 00 RVP 40 07
Deoiling cartridge item 00 RVP 40 05
3 vanes item 00 RVP 40 04
Sealing kit item 00 RVP 40 06
Check valve item 00 RVP 40 03
Suction filter item FC 35
Ballast valve item integrated

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.35
OIL-BATH VACUUM PUMP RVP 60
3D drawings are available on vuototecnica.net

Flow rate Time

RVP 60

Vacuum mbar

Flow rate Time

Vacuum mbar

7.36
OIL-BATH VACUUM PUMP RVP 60

3D drawings are available on vuototecnica.net

Item RVP 60
Frequency 50 Hz 60 Hz
Flow rate m3/h 60.0 72.0
Final pressure mbar abs. 0.5
H2O steam quantity
permitted Kg/h 1
Motor performance 3~ Volt 230/400 ± 10% 275/480 ± 10%
Motor power 3~ Kw 1.50 1.80
Motor protection IP 55
Rotation speed g/min-1 1450 1740
Motor shape B14
Motor size 100
Noise level dB(A) 65 66
Max weight Kg 59.0
A 615
B 420
C 290
D 148
E 317
F 217
G Ø M8
H 298 7
I 276
L 15
M 129
N 140
O 200
P 89
R Ø gas G1”1/4

Accessories and Parts RVP 60

Oil charge L 2
Lubricating oil type VT OIL 100
Oil filter item 00 RVP 60 07
2 deoiling cartridges item 00 RVP 60 05
3 vanes item 00 RVP 60 04
Sealing kit item 00 RVP 60 06
Check valve item 00 RVP 60 03
Suction filter item FC 35
Ballast valve item integrated

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.37
OIL-BATH VACUUM PUMP RVP 100
3D drawings are available on vuototecnica.net

Flow rate Time

RVP 1 00

Vacuum mbar

Flow rate Time

RVP 1 00

Vacuum mbar

7.38
OIL-BATH VACUUM PUMP RVP 100

3D drawings are available on vuototecnica.net

Item RVP 100
Frequency 50 Hz 60 Hz
Flow rate m3/h 100.0 120.0
Final pressure mbar abs. 0.5
H2O steam quantity
permitted Kg/h 1.5
Motor performance 3~ Volt 230/400 ± 10% 275/480 ± 10%
Motor power 3~ Kw 2.2 3.0
Motor protection IP 55
Rotation speed g/min-1 1450 1740
Motor shape B14
Motor size 100
Noise level dB(A) 67 69
Max weight Kg 78.0
A 710
B 405
C 280
D 175
E 360
F 275
G Ø M8
H 290 7
I 277
L 15
M 113
N 170
O 200
P 90
R Ø gas G1”1/4

Accessories and Parts RVP 100

Oil charge L 2
Lubricating oil type VT OIL 100
Oil filter item 00 RVP 100 07
2 deoiling cartridges item 00 RVP 100 05
3 vanes item 00 RVP 100 04
Sealing kit item 00 RVP 100 06
Check valve item 00 RVP 100 03
Suction filter item FC 35
Ballast valve item integrated

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.39
OIL-BATH VACUUM PUMPS RVP 160 and RVP 200
3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time

RVP 160 RVP 200

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

RVP 160 RVP 200

Vacuum mbar Vacuum mbar

7.40
OIL-BATH VACUUM PUMPS RVP 160 and RVP 200

3D drawings are available on vuototecnica.net

Item RVP 160 RVP 200
Frequency 50 Hz 60 Hz 50 Hz 60 Hz
Flow rate m3/h 160.0 190.0 200.0 240.0
Final pressure mbar abs. 0.5 0.5
H2O steam quantity
permitted Kg/h 2.5 4
Motor performance 3~ Volt 400/690 ± 10% 480/830 ± 10% 400/690 ± 10% 480/830 ± 10%
Motor power 3~ Kw 4 5.5 4 5.5
Motor protection IP 55 55
Rotation speed g/min-1 1450 1740 1450 1740
Motor shape B14 B14
Motor size 112 112
Noise level dB(A) 72 73 74 75
Max weight kg 142.0 145.0
A 761 761
B 495 495
C 411 411
D 192 192
E 243 243
E1 366 366
F 326 326
F1 205 205
G Ø M10 M10
H 310 310 7
I 305 305
L 25 25
M 165 165
N 189 189
O 80 80
P 65 65
R Ø gas G2” G2”

Accessories and Parts RVP 160 RVP 200

Oil charge L 8 8
Lubricating oil type VT OIL 100 VT OIL 100
Oil filter item 00 RVP 160 07 00 RVP 200 07
3 deoiling cartridges item 00 RVP 160 05 00 RVP 200 05
3 vanes item 00 RVP 160 04 00 RVP 200 04
Sealing kit item 00 RVP 160 06 00 RVP 200 06
Check valve item 00 RVP 160 03 00 RVP 200 03
Suction filter item FC 60 FC 60
Ballast valve item integrated integrated

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.41
OIL-BATH VACUUM PUMPS RVP 250 and RVP 300
3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time

RVP 250 RVP 300

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

RVP 250 RVP 300

Vacuum mbar Vacuum mbar

7.42
OIL-BATH VACUUM PUMPS RVP 250 and RVP 300

3D drawings are available on vuototecnica.net

Item RVP 250 RVP 300
Frequency 50 Hz 60 Hz 50 Hz 60 Hz
Flow rate m3/h 250 300 300 360
Final pressure mbar abs. 0.5 0.5
H2O steam quantity
permitted Kg/h 4 4.5
Motor performance 3~ Volt 400/690 ± 10% 480/830 ± 10% 400/690 ± 10% 480/830 ± 10%
Motor power 3~ Kw 5.5 7.5 7.5 11
Motor protection IP 55 55
Rotation speed g/min-1 1450 1740 1450 1740
Motor shape B5 B5
Motor size 132 132
Noise level dB(A) 74 75 75 76
Max weight Kg 198.0 212.0
A 975 1010
B 579 579
C 411 411
D 287 287
E 303 303
E1 390 390
F 385 420
F1 350 350
G Ø M10 M10
H 421 421 7
I 369 369
L 50 50
M 185 185
N 267 267
O 242 242
P 150 150
R Ø gas G2” G2”

Accessories and Parts RVP 250 RVP 300

Oil charge L 8 8
Lubricating oil type VT OIL 100 VT OIL 100
Oil filter item 00 RVP 250 07 00 RVP 300 07
4 deoiling cartridges item 00 RVP 250 05 00 RVP 300 05
3 vanes item 00 RVP 250 04 00 RVP 300 04
Sealing kit item 00 RVP 250 06 00 RVP 300 06
Check valve item 00 RVP 250 03 00 RVP 300 03
Suction filter item FC 60 FC 60
Ballast valve item integrated integrated

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.43
LUBRICATED VACUUM PUMP
ACCESSORIES AND SPARE PARTS
3D drawings are available on vuototecnica.net

Item Quantity For pump item

Fibre vane 00 VTL 02 10 4 VTL 2

00 VTL 04 10 4 VTL 4
00 VTL 05 10 6 VTL 5 - VTLP 5
00 VTL 10 10 6 VTL 10 - VTLP 10
00 VTL 10F 10 6 VTL 10/F - VTLP 10/F
00 VTL 10FG 10 6 VTL 10/FG - VTLP 10/FG
00 VTL 15F 10 6 VTL 15/F - VTLP 15/F
00 VTL 15FG 10 6 VTL 15/FG - VTLP 15/FG
00 VTL 20F 10 6 VTL 20/F - VTLP 20/F
00 VTL 20FG 10 6 VTL 20/FG - VTLP 20/FG
7 00 VTL 25FG 10 6 VTL 25/FG - VTLP 25/FG
00 VTL 30FG 10 6 VTL 30/FG - VTLP 30/FG
00 VTL 35FG 10 6 VTL 35/FG - VTLP 35/FG
00 VTL 40G1 10 6 VTL 40/G1 - VTLP 40/G1
00 VTL 50G1 10 6 VTL 50/G1 - VTLP 50/G1
00 VTL 65G1 10 6 VTL 65/G1 - VTLP 65/G1
00 VTL 75G1 10 6 VTL 75/G1 - VTLP 75/G1
00 VTL 90G1 10 6 VTL 90/G1 - VTLP 90/G1
00 VTL 105G1 10 6 VTL 105/G1 - VTLP 105/G1
00 RVP 15 04 3 RVP15
00 RVP 21 04 3 RVP21
00 RVP 40 04 3 RVP40
00 RVP 60 04 3 RVP60
00 RVP 100 04 3 RVP100
00 RVP 160 04 3 RVP160
00 RVP 200 04 3 RVP200
00 RVP 250 04 3 RVP250
00 RVP 300 04 3 RVP300

7.44
LUBRICATED VACUUM PUMP
ACCESSORIES AND SPARE PARTS

3D drawings are available on vuototecnica.net

Item Quantity For pump item

Sealing kit 00 KIT VTL 02 1 VTL 2

00 KIT VTL 04 1 VTL 4
00 KIT VTL 05 1 VTL 5 - VTLP 5
00 KIT VTL 10 1 VTL 10 - VTLP 10
00 KIT VTL 10F 1 VTL 10/F - VTLP 10/F
00 KIT VTL 10FG 1 VTL 10/FG - VTLP 10/FG
00 KIT VTL 15F 1 VTL 15/F - VTLP 15/F
00 KIT VTL 15FG 1 VTL 15/FG - VTLP 15/FG
00 KIT VTL 20F 1 VTL 20/F - VTLP 20/F
00 KIT VTL 20FG 1 VTL 20/FG - VTLP 20/FG
00 KIT VTL 25FG 1 VTL 25/FG - VTLP 25/FG
00 KIT VTL 30FG 1 VTL 30/FG - VTLP 30/FG
00 KIT VTL 35FG 1 VTL 35/FG - VTLP 35/FG
00 KIT VTL 40G1 1 VTL 40/G1 - VTLP 40/G1
00 KIT VTL 50G1 1 VTL 50/G1 - VTLP 50/G1
00 KIT VTL 65G1 1 VTL 65/G1 - VTLP 65/G1
00 KIT VTL 75G1 1 VTL 75/G1 - VTLP 75/G1
00 KIT VTL 90G1 1 VTL 90/G1 - VTLP 90/G1
00 KIT VTL 105G1 1 VTL 105/G1 - VTLP 105/G1

00 RVP 15 06 1 RVP15
00 RVP 21 06 1 RVP21
00 RVP 40 06 1 RVP40
00 RVP 60 06 1 RVP60
00 RVP 100 06 1 RVP100
00 RVP 160 06 1 RVP160
00 RVP 200 06 1 RVP200
00 RVP 250 06 1 RVP250
00 RVP 300 06 1 RVP300

Check valves 10 01 15 1 VTL 2

10 02 15 1 VTL 4 7
10 02 10 1 VTL 5 - VTLP 5
10 03 10 1 VTL 10 - VTLP 10
VTL 10/F - VTLP 10/F
VTL 10/FG - VTLP 10/FG
VTL 15/F - VTLP 15/F
VTL 15/FG - VTLP 15/FG
VTL 20/F - VTLP 20/F
VTL 20/FG - VTLP 20/FG
10 04 10 1 VTL 25/FG - VTLP 25/FG
VTL 30/FG - VTLP 30/FG
VTL 35/FG - VTLP 35/FG
10 05 10 1 VTL 40/G1 - VTLP 40/G1
VTL 50/G1 - VTLP 50/G1
VTL 65/G1 - VTLP 65/G1
10 06 10 1 VTL 75/G1 - VTLP 75/G1
VTL 90/G1 - VTLP 90/G1
10 07 10 1 VTL 105/G1 - VTLP 105/G1

7.45
LUBRICATED VACUUM PUMP
ACCESSORIES AND SPARE PARTS
3D drawings are available on vuototecnica.net

Item Quantity For pump item

Suction filters FB 5 1 VTL 2

FB 10 1 VTL 4
VTL 5 - VTLP 5
FB 20 1 VTL 10 - VTLP 10
VTL 10/F - VTLP 10/F
VTL 10/FG - VTLP 10/FG
VTL 15/F - VTLP 15/F
VTL 15/FG - VTLP 15/FG
FB VTL 20/F - VTLP 20/F
VTL 20/FG - VTLP 20/FG
FB 28 1 VTL 25/FG - VTLP 25/FG
VTL 30/FG - VTLP 30/FG
VTL 35/FG - VTLP 35/FG
FB 30 1 VTL 40/G1 - VTLP 40/G1
VTL 50/G1 - VTLP 50/G1
VTL 65/G1 - VTLP 65/G1
FB 40 1 VTL 75/G1 - VTLP 75/G1
VTL 90/G1 - VTLP 90/G1
FB 50 1 VTL 105/G1 - VTLP 105/G1
FB

FC 10 1 VTL 4
VTL 5 - VTLP 5
FC 20 1 VTL 10 - VTLP 10
VTL 10/F - VTLP 10/F
VTL 10/FG - VTLP 10/FG
VTL 15/F - VTLP 15/F
VTL 15/FG - VTLP 15/FG
VTL 20/F - VTLP 20/F
VTL 20/FG - VTLP 20/FG
RVP15
FC RVP21
FC 25 1 VTL 25/FG - VTLP 25/FG
VTL 30/FG - VTLP 30/FG
VTL 35/FG - VTLP 35/FG
FC 30 1 VTL 40/G1 - VTLP 40/G1
VTL 50/G1 - VTLP 50/G1
VTL 65/G1 - VTLP 65/G1
FC 35 1 RVP40
7 RVP60
RVP100
FC 40 1 VTL 75/G1 - VTLP 75/G1
VTL 90/G1 - VTLP 90/G1
FC 50 1 VTL 105/G1 - VTLP 105/G1
FC 60 1 RVP160
RVP200
RVP250
RVP300

Adjustable drip oiler 00 VTL 00 11 VTL - All

VTLP - All

7.46
LUBRICATED VACUUM PUMP
ACCESSORIES AND SPARE PARTS

3D drawings are available on vuototecnica.net

Item Quantity For pump item

Oil level switch 00 LP VTL 99 1 VTLP - All

Oil filters 00 LP VTL 40 1 VTLP - All

00 RVP 40 07 1 RVP40
00 RVP 60 07 1 RVP60
00 RVP 100 07 1 RVP100
00 RVP 160 07 1 RVP160
00 RVP 200 07 1 RVP200
00 RVP 250 07 1 RVP250
00 RVP 300 07 1 RVP300

Deoiling cartridges 00 VTL 75G1 29 1 VTL 75/G1 - VTLP 75/G1

00 VTL 90G1 29 1 VTL 90/G1 - VTLP 90/G1
00 VTL 105G1 29 1 VTL 105/G1 - VTLP 105/G1
00 RVP 15 05 1 RVP15
00 RVP 21 05 1 RVP21
00 RVP 40 05 1 RVP40
00 RVP 60 05 2 RVP60
00 RVP 100 05 2 RVP100
00 RVP 160 05 3 RVP160
00 RVP 200 05 3 RVP200
00 RVP 250 05 4 RVP250
00 RVP 300 05 4 RVP300

Mineral lubricating oil ISO 32 - 68 - 100 - 150 1 - 2 - 5 - 10 L packs

Synthetic lubricating oil VT OIL 32 - 68 - 100 1 - 2 - 5 - 10 L packs 7

“Non-toxic” synthetic oil

for the food industry VT OIL FI 68 - 100 1 - 2 - 5 - 10 L packs

7.47
DRY VACUUM PUMPS VTS 2 and 4

These small lubrication-free rotary vane vacuum pumps have a

suction flow rate of 2 and 4 m3/h. The particular shape of the working
chamber and the special graphite, with which the locking flanges and
vanes are made, allow these pumps to operate with no lubrication.
3D drawings are available on vuototecnica.net

The rotor is cantilevered-fitted on the motor shaft, thus reducing

overall dimensions to the minimum. The motor and the pump are
cooled by the motor fan (surface cooling).
A filter that functions as a silencer is installed on the suction inlet.
We strongly recommend installing a filter on the suction inlet against
possible impurities. These pumps are not recommended when the
fluid to be sucked contains water or oil vapours or condensations.
Vacuum pumps VTS 2 and 4 can also be supplied with single-phase
electric motor.

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

7.48
DRY VACUUM PUMPS VTS 2 and 4

3D drawings are available on vuototecnica.net

Item VTS 2 VTS 4
Frequency 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 2.0 2.4 4.0 4.8
Final pressure mbar abs. 200 150
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10%
Motor power 3~ 0.12 0.15 0.18 0.21
Kw 1~ 0.12 0.15 0.18 0.21
Motor protection IP 55 55
Rotation speed g/min-1 2800 3300 2800 3300
Motor shape
Motor size 56 63
Noise level dB(A) 64 66 64 66
Max weight 3~ 5.3 6.8
Kg 1~ 5.5 7.0
A 217 251
B 180 186
C 121 131 7
D 66 78
E 71 81
F 80 92
H 35 45
I 90 100
L 79 73
M 11 13
R Ø gas G1/4” G1/4”

Accessories and Parts VTS 2 VTS 4

4 graphite vanes item 00 VTS 02 10 00 VTS 04 10
Front flange
complete with graphite disc item 00 VTS 02 11 00 VTS 04 11
Rear flange
complete with graphite disc item 00 VTS 02 15 00 VTS 02 15
Sealing kit item 00 KIT VTS 02 00 KIT VTS 04
Check valve item 10 01 15 10 01 15
Suction filter item FB 5 FB 5
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTS 2 M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.49
DRY VACUUM PUMPS VTS 6 and 10

These lubrication-free rotary vane vacuum pumps

have a suction flow rate of 6 and 10 m3/h. The
particular shape of the working chamber and the
special graphite, with which the locking flanges and
3D drawings are available on vuototecnica.net

vanes are made, allow these pumps to operate with

no lubrication.
The rotor is cantilevered-fitted on the motor shaft,
thus reducing overall dimensions to the minimum.
The motor and the pump are cooled by the motor
fan (surface cooling).
A filter that functions as a silencer is installed on
the suction inlet. VTS 6
We strongly recommend installing a filter on the
suction inlet against possible impurities. These
pumps are not recommended when the fluid
to be sucked contains water or oil vapours or
condensations.
Vacuum pumps VTS 6 and 10 can also be supplied
with single-phase electric motor.
VTS 10

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar

7.50
DRY VACUUM PUMPS VTS 6 and 10

3D drawings are available on vuototecnica.net

Item VTS 6 VTS 10
Frequency 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 6.0 7.2 10.0 12.0
Final pressure mbar abs. 80 80
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10%
Motor power 3~ 0.25 0.30 0.37 0.40
Kw 1~ 0.25 0.30 0.37 0.40
Motor protection IP 55 55
Rotation speed g/min-1 1400 1680 1400 1680
Motor shape Special Special
Motor size 71 71
Noise level dB(A) 64 66 64 66
Max weight 3~ 11.8 15.0
Kg 1~ 12.0 15.2
A 268 290
B 210 182
C 156 156
D 55 55 7
E 155 155
F 58 88
H 43 53
I 115 115
L 82.5 52.5
M 12.5 12.5
N 68 13
R Ø gas G3/8” G3/8”

Accessories and Parts VTS 6 VTS 10

6 graphite vanes item 00 VTS 06 10 00 VTS 10 10
Front flange
complete with graphite disc item 00 VTS 06 07 00 VTS 10 11
Rear flange
complete with graphite disc item 00 VTS 06 12 00 VTS 10 20
Sealing kit item 00 KIT VTS 06 00 KIT VTS 10
Check valve item 10 02 10 10 02 10
Suction filter item FB 10/FC 10 FB 10/FC 10
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTS 6 M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.51
DRY VACUUM PUMPS VTS 10/FG - 35/FG

These lubrication-free rotary vane vacuum pumps have a suction

flow rate of 10, 15, 20, 25, 30 and 35 m3/h. The particular shape of
the working chamber and the special graphite, with which the locking
flanges and vanes are made, allow these pumps to operate with no
3D drawings are available on vuototecnica.net

lubrication.
The pump rotor is cantilevered-fitted on the motor shaft and
supported by independent bearings housed in the two pump flanges.
The pump and the electric motor are, therefore, two independent units
and fixed onto a special support and connected to each other via an
elastic transmission joint.
All this allows using standard electric motors, in the shapes and sizes
indicated in the table.
The pump is surface cooled. Heat is dispersed from the outer surface,
suitably finned, by means of a radial fan placed between motor and
pump.
A filter that functions as a silencer is installed on the suction inlet.
We strongly recommend installing a filter on the suction inlet against
possible impurities. These pumps are not recommended when the
fluid to be sucked contains water or oil vapours or condensations.
Also this range of pumps can be supplied with single-phase electric
motors.

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.56
DRY VACUUM PUMPS VTS 10/FG, 15/FG and 20/FG

3D drawings are available on vuototecnica.net

Item VTS 10/FG VTS 15/FG VTS 20/FG
Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 10.0 12.0 15.0 18.0 20.0 24.0
Final pressure mbar abs. 80 80 80
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10% 230±10%
Motor power 3~ 0.35 0.40 0.55 0.66 0.55 0.66
Kw 1~ 0.25 0.30 0.55 0.66 0.55 0.66
Motor protection IP 55 55 55
Rotation speed g/min-1 1400 1680 1400 1680 1400 1680
Motor shape B14 B14 B14
Motor size 80 80 80
Noise level dB(A) 64 66 65 67 65 67
Max weight 3~ 22.0 24.0 27.3
Kg 1~ 22.4 24.4 27.8 7
A 430 450 470
B 265 265 265
C 170 170 170
D 65 65 65
E 340 340 340
F 25 45 65
H 133 133 133
I 130 130 130
L 55 55 55
M 80 80 80
N 73 83 93
R Ø gas G1/2” G1/2” G1/2”

Accessories and Parts VTS 10/FG VTS 15/FG VTS 20/FG

6 graphite vanes item 00 VTS 10FG 10 00 VTS 15FG 10 00 VTS 20FG 10
Sealing kit item 00 KIT VTS 10FG 00 KIT VTS 15FG 00 KIT VTS 20FG
Check valve item 10 03 10 10 03 10 10 03 10
Suction filter item FB 20/FC 20 FB 20/FC 20 FB 20/FC 20
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTS 10/FG M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.57
DRY VACUUM PUMPS VTS 25/FG, 30/FG and 35/FG
3D drawings are available on vuototecnica.net

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

Flow rate Time Flow rate Time Flow rate Time

Vacuum mbar Vacuum mbar Vacuum mbar

7.58
DRY VACUUM PUMPS VTS 25/FG, 30/FG and 35/FG

3D drawings are available on vuototecnica.net

Item VTS 25/FG VTS 30/FG VTS 35/FG
Frequency 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz
Flow rate m3/h 25.0 30.0 30.0 36.0 35.0 42.0
Final pressure mbar abs. 80 80 80
Motor performance 3~ 230/400±10% 265/460±10% 230/400±10% 265/460±10% 230/400±10% 265/460±10%
Volt 1~ 230±10% 230±10% 230±10%
Motor power 3~ 0.75 0.90 0.75 0.90 1.10 1.35
Kw 1~ 0.75 0.75 1.10
Motor protection IP 55 55 55
Rotation speed g/min-1 1410 1640 1410 1640 1440 1750
Motor shape B14 B14 B14
Motor size 80 80 80
Noise level dB(A) 66 68 68 70 70 72
Max weight 3~ 29 32 34
Kg 1~ 29.5 32.5 34.5 7
A 470 490 510
B 265 265 265
C 170 170 170
D 65 65 65
E 385 385 385
F 20 40 60
H 133 133 133
I 130 130 130
L 55 55 55
M 80 80 80
N 73 83 93
R Ø gas G3/4” G3/4” G3/4”

Accessories and Parts VTS 25/FG VTS 30/FG VTS 35/FG

6 graphite vanes item 00 VTS 25FG 10 00 VTS 30FG 10 00 VTS 35FG 10
Sealing kit item 00 KIT VTS 25FG 00 KIT VTS 30FG 00 KIT VTS 35FG
Check valve item 10 04 10 10 04 10 10 04 10
Suction filter item FB 28/FC 25 FB 28/FC 25 FB 28/FC 25
Note: Add the letter M to the item for a pump supplied with a single-phase electric motor (Example: VTS 25/FG M).

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = cfm= m3/h x 0.588; inch Hg= mbar x 0.0295; psi= bar x 14.6
25.4 453.6 0.4536
7.59
DRY VACUUM PUMP
ACCESSORIES AND SPARE PARTS
3D drawings are available on vuototecnica.net

Item Quantity For pump item

Graphite vanes 00 VTS 02 10 4 VTS 2

00 VTS 04 10 4 VTS 4
00 VTS 06 10 6 VTS 6
00 VTS 10 10 6 VTS 10
00 VTS 10F 10 6 VTS 10/F
00 VTS 15F 10 6 VTS 15/F
00 VTS 20F 10 6 VTS 20/F
00 VTS 25F 10 6 VTS 25/F
00 VTS 10FG 10 6 VTS 10/FG
00 VTS 15FG 10 6 VTS 15/FG
00 VTS 20FG 10 6 VTS 20/FG
00 VTS 25FG 10 6 VTS 25/FG
00 VTS 30FG 10 6 VTS 30/FG
00 VTS 35FG 10 6 VTS 35/FG

Front flange 00 VTS 02 11 1 VTS 2

complete with graphite disc 00 VTS 04 11 1 VTS 4

Rear flange 00 VTS 02 15 1 VTS 2

complete with graphite disc VTS 4

Front flange 00 VTS 06 07 1 VTS 6

complete with graphite disc 00 VTS 10 11 1 VTS 10
00 VTS 10F 15 1 VTS 10/F
VTS 15/F
VTS 20/F
VTS 25/F
7

Rear flange 00 VTS 06 12 1 VTS 6

complete with graphite disc 00 VTS 10 20 1 VTS 10
00 VTS 10F 19 1 VTS 10/F
VTS 15/F
VTS 20/F
00 VTS 25F 05 1 VTS 25/F

7.60
DRY VACUUM PUMP
ACCESSORIES AND SPARE PARTS

3D drawings are available on vuototecnica.net

Item Quantity For pump item

Sealing kit 00 KIT VTS 02 1 VTS 2

00 KIT VTS 04 1 VTS 4
00 KIT VTS 06 1 VTS 6
00 KIT VTS 10 1 VTS 10
00 KIT VTS 10F 1 VTS 10/F
00 KIT VTS 15F 1 VTS 15/F
00 KIT VTS 20F 1 VTS 20/F
00 KIT VTS 25F 1 VTS 25/F
00 KIT VTS 10FG 1 VTS 10/FG
00 KIT VTS 15FG 1 VTS 15/FG
00 KIT VTS 20FG 1 VTS 20/FG
00 KIT VTS 25FG 1 VTS 25/FG
00 KIT VTS 30FG 1 VTS 30/FG
00 KIT VTS 35FG 1 VTS 35/FG

Check valves 10 01 15 1 VTS 2

VTS 4
10 02 10 VTS 6
1 VTS 10
10 03 10 1 VTS 10/F
VTS 15/F
VTS 20/F
VTS 10/FG
VTS 15 /FG
VTS 20/FG
10 04 10 1 VTS 25/F
VTS 25/FG
VTS 30/FG
VTS 35/FG

Suction filters FB 5 1 VTS 2

VTS 4
VTS 6
FB 10 1 VTS 10
FB 20 1 VTS 10/F
VTS 15/F
VTS 20/F
VTS 10/FG 7
VTS 15/FG
VTS 20/FG
FB 28 1 VTS 25/F
VTS 25/FG
FB VTS 30/FG
VTS 35/FG

FC 10 1 VTS 10
FC 20 1 VTS 10/F
VTS 15/F
VTS 20/F
VTS 10/FG
VTS 15/FG
VTS 20/FG
FC 25 1 VTS 25/F
VTS 25/FG
FC VTS 30/FG
VTS 35/FG

7.61
MINI PUMP SETS - GENERAL DESCRIPTION

Mini pump sets are small independent vacuum-producing units with reduced size.
They are composed of:
- A small welded sheet steel tank with perfect vacuum seal.
- A low-flow rate dry or lubricated rotating vane vacuum pump.
3D drawings are available on vuototecnica.net

- A mini digital vacuum switch for adjusting the maximum level of vacuum.
- A vacuum gauge for reading the level of vacuum.
- Switchgear enclosed in a special casing.
- A manual valve for vacuum interception.
- A cock for condensation drainage.
The level of vacuum, preset via the digital vacuum switch is automatically maintained in
the tank.
Mini pump sets can also be supplied with single-phase or DC electric motors and they
are suited for equipping fixed or mobile working units that require vacuum, such as:
- Trolleys with vacuum cups for fixing and transporting glass and crystals.
- Vacuum clamping systems for ski maintenance, marble processing and for polishing
copper, pewter or silver objects.
- Hoists with vacuum cups for lifting television sets and household appliances for glass
installation in door and window frames, for laying ceramic tiles, for feeding sheet metal
into presses, etc.

7.62
MINI PUMP SETS DO 06V ... and DO 10V ... WITH DRY VACUUM PUMPS

3D drawings are available on vuototecnica.net

Digital vacuum switch Vacuum cut-off valve Switchgear
Item 12 40 10 Item 13 02 11

Dry vacuum Vacuum gauge

pump Item 09 05 10

Handle

Cock for condensation Tank

drainage Item 13 02 11

Tank Pump Electric Motor C D E F H Weight Filter

Item performance switchgear accessories
Litres Mod. Volt item Kg item
DO 06V VTS 2 6 VTS 2 3 ~ 230/400-50Hz DO 06 97V 60 180 135 181 320 14.8 FB 10 / FC 10
DO 06V VTS 2 M 6 VTS 2 M 1 ~ 230-50Hz DO 06 98V 60 180 135 181 320 15.0 FB 10 / FC 10
DO 06V VTS 4 6 VTS 4 3 ~ 230/400-50Hz DO 06 97V 60 203 135 191 320 16.3 FB 10 / FC 10
DO 06V VTS 4 M 6 VTS 4 M 1 ~ 230-50Hz DO 06 98V 60 203 135 191 320 16.5 FB 10 / FC 10
DO 06V VTS 6 6 VTS 6 3 ~ 230/400-50Hz DO 06 97V 60 270 135 216 320 21.3 FB 10 / FC 10
DO 06V VTS 6 M 6 VTS 6 M 1 ~ 230-50Hz DO 06 98V 60 270 135 216 320 21.5 FB 10 / FC 10

DO 10V VTS 2 10 VTS 2 3 ~ 230/400-50Hz DO 06 97V 100 180 175 221 360 19.0 FB 10 / FC 10
DO 10V VTS 2 M 10 VTS 2 M 1 ~ 230-50Hz DO 06 98V 100 180 175 221 360 19.2 FB 10 / FC 10
DO 10V VTS 4 10 VTS 4 3 ~ 230/400-50Hz DO 06 97V 100 203 175 231 360 20.5 FB 10 / FC 10
DO 10V VTS 4 M 10 VTS 4 M 1 ~ 230-50Hz DO 06 98V 100 203 175 231 360 20.7 FB 10 / FC 10
DO 10V VTS 6 10 VTS 6 3 ~ 230/400-50Hz DO 06 97V 100 270 175 256 360 25.5 FB 10 / FC 10
DO 10V VTS 6 M 10 VTS 6 M 1 ~ 230-50Hz DO 06 98V 100 270 175 256 360 25.7 FB 10 / FC 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.63
MINI PUMP SETS DO 06V ... and DO 10V ... WITH LUBRICATED VACUUM PUMPS
3D drawings are available on vuototecnica.net

Digital vacuum switch Vacuum cut-off valve Switchgear

Item 12 40 10 Item 13 02 11

Check valve

Dry vacuum Vacuum gauge

pump Item 09 05 10

Handle

Cock for Tank

condensation drainage
Item 13 02 11

Tank Pump Electric Motor C D E F H Weight Filter

Item performance switchgear accessories
Litres Mod. Volt item Kg item
DO 06V VTL 2 6 VTL 2 3 ~ 230/400-50Hz DO 06 97V 60 250 135 198 320 15.2 FB 10 / FC 10
DO 06V VTL 2 M 6 VTL 2 M 1 ~ 230-50Hz DO 06 98V 60 250 135 198 320 15.5 FB 10 / FC 10
DO 06V VTL 4 6 VTL 4 3 ~ 230/400-50Hz DO 06 97V 60 280 135 198 320 16.8 FB 10 / FC 10
DO 06V VTL 4 M 6 VTL 4 M 1 ~ 230-50Hz DO 06 98V 60 280 135 198 320 17.0 FB 10 / FC 10
DO 06V VTL 5 6 VTL 5 3 ~ 230/400-50Hz DO 06 97V 60 260 135 310 320 24.0 FB 10 / FC 10
DO 06V VTL 5 M 6 VTL 5 M 1 ~ 230-50Hz DO 06 98V 60 260 135 310 320 24.5 FB 10 / FC 10

DO 10V VTL 2 10 VTL 2 3 ~ 230/400-50Hz DO 06 97V 100 250 175 238 360 19.4 FB 10 / FC 10
DO 10V VTL 2 M 10 VTL 2 M 1 ~ 230-50Hz DO 06 98V 100 250 175 238 360 19.7 FB 10 / FC 10
DO 10V VTL 4 10 VTL 4 3 ~ 230/400-50Hz DO 06 97V 100 280 175 238 360 21.0 FB 10 / FC 10
DO 10V VTL 4 M 10 VTL 4 M 1 ~ 230-50Hz DO 06 98V 100 280 175 238 360 21.2 FB 10 / FC 10
DO 10V VTL 5 10 VTL 5 3 ~ 230/400-50Hz DO 06 97V 100 260 175 350 360 28.2 FB 10 / FC 10
DO 10V VTL 5 M 10 VTL 5 M 1 ~ 230-50Hz DO 06 98V 100 260 175 350 360 28.7 FB 10 / FC 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.64
MINI PUMP SETS DO 20V ...

3D drawings are available on vuototecnica.net

Switchgear Vacuum gauge Vacuum cut-off valve
Item 09 05 10 Item 13 03 11

Vacuum pump Digital vacuum switch

Item 12 40 10

Handle

Cock for
Tank condensation drainage
Item 13 02 11

Tank Pump Electric Motor D F H Weight Filter

Item performance switchgear accessories 7
Litres Mod. Volt item Kg item

DO 20V VTL 5 20 VTL 5 3 ~ 230/400-50Hz DO 06 97V 320 345 360 38.5 FB 20 / FC 20

DO 20V VTL 5 M 20 VTL 5 M 1 ~ 230/50Hz DO 06 98V 320 345 360 39.0 FB 20 / FC 20
DO 20V VTL 10 20 VTL 10 3 ~ 230/400-50Hz DO 06 97V 352 345 360 44.5 FB 20 / FC 20
DO 20V VTL 10 M 20 VTL 10 M 1 ~ 230-50Hz DO 06 98V 352 345 360 45.0 FB 20 / FC 20
DO 20V VTL 10/FG 20 VTL 10/FG 3 ~ 230/400-50Hz DO 06 97V 390 360 360 49.0 FB 20 / FC 20
DO 20V VTL 10/FG M 20 VTL 10/FG M 1 ~ 230-50Hz DO 06 98V 390 360 360 49.5 FB 20 / FC 20
DO 20V VTL 15/FG 20 VTL 15/FG 3 ~ 230/400-50Hz DO 06 97V 410 360 360 51.0 FB 20 / FC 20
DO 20V VTL 15/FG M 20 VTL 15/FG M 1 ~ 230-50Hz DO 06 98V 410 360 360 51.5 FB 20 / FC 20
DO 20V RVP 15 20 RVP 15 3 ~ 230/400-50Hz DO 06 97V 350 335 360 39.0 FB 20 / FC 20
DO 20V RVP 15 M 20 RVP 15 M 1 ~ 230-50Hz DO 06 98V 335 335 360 39.5 FB 20 / FC 20
DO 20V VTL 20/FG 20 VTL 20/FG 3 ~ 230/400-50Hz DO 06 97V 430 360 360 54.0 FB 20 / FC 20
DO 20V VTL 20/FG M 20 VTL 20/FG M 1 ~ 230-50Hz DO 06 98V 430 360 360 54.5 FB 20 / FC 20
DO 20V RVP 21 20 RVP 21 3 ~ 230/400-50Hz DO 06 97V 430 315 360 42.5 FB 20 / FC 20
DO 20V RVP 21 M 20 RVP 21 M 1 ~ 230-50Hz DO 06 98V 430 315 360 43.0 FB 20 / FC 20

Note: All RVP pumps .. are equipped as standard with an FC filter .. suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.65
HORIZONTAL PUMP SETS - GENERAL DESCRIPTION

As a standard, these pump sets are built with various capacities and they are composed of:
- A horizontal welded sheet steel tank with perfect vacuum seal.
- A rotary vane vacuum pump to be selected according to the required suction
flow rate and level of vacuum.
3D drawings are available on vuototecnica.net

- A digital vacuum switch for adjusting the level of vacuum within which to operate.
- A vacuum gauge for a direct reading of the level of vacuum in the tank.
- A switchgear enclosed in a special plastic casing for tanks from 25 to 50 litres
and in a watertight metal casing for tanks of 100 litres upwards.
- A manual valve for vacuum interception.
- A cock for condensation drainage.
The level of vacuum, preset via the digital vacuum switch is automatically maintained in the tank.
The pump operation can be both continuous or automatic.
Pump sets are normally used for handling particularly heavy or valuable loads since, in case of electricity
failure, they allow the vacuum cups to maintain the grip for a certain amount of time, according to the tank
capacity.
These pump sets are recommended for multi-point applications, to centralise vacuum.
These pump sets offer many advantages in energy consumption, since the pump operates only when
required by the machine.

7.66
HORIZONTAL PUMP SETS DO 25V ...

Digital vacuum switch Vacuum pump Vacuum gauge Switchgear

Item 12 40 10 Item 09 05 10

3D drawings are available on vuototecnica.net

Vacuum cut-off valve
Item 13 03 10

Cock for condensation

drainage Item 13 03 11

Tank Pump Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DO 25V VTL 5 25 VTL 5 3 ~ 230/400-50Hz DO 06 97V 540 570 G1/2” 33.5 FB 20 / FC 20
DO 25V VTL 5 M 25 VTL 5 M 1 ~ 230/50Hz DO 06 98V 540 570 G1/2” 34.0 FB 20 / FC 20
DO 25V VTL 10 25 VTL 10 3 ~ 230/400-50Hz DO 06 97V 540 570 G1/2” 39.5 FB 20 / FC 20
DO 25V VTL 10 M 25 VTL 10 M 1 ~ 230-50Hz DO 06 98V 540 570 G1/2” 40.0 FB 20 / FC 20
DO 25V RVP 15 25 RVP 15 3 ~ 230/400-50Hz DO 06 97V 525 570 G1/2” 35.0 FB 20 / FC 20
DO 25V RVP 15 M 25 RVP 15 M 1 ~ 230-50Hz DO 06 98V 525 570 G1/2” 35.5 FB 20 / FC 20
Note: Add the letters SR to the item for a pump set supplied with sheets for movement (Example: DO 25V VTL 10 SR).
All RVP pumps .. are equipped as standard with an FC filter .. suitable for the size of their suction connection.

HORIZONTAL PUMP SETS DO 50V ...

Vacuum pump Vacuum gauge Switchgear
Item 09 05 10

Digital vacuum switch

3D drawings are available on vuototecnica.net

- Two rotary vane vacuum pumps to be selected according to the required suction
flow rate and level of vacuum.
- A vacuum gauge for a direct reading of the level of vacuum in the tank.
- Two manual valves for vacuum interception, located between the pumps and the tank and one installed
on the tank, for the exclusion or connection of the pump set on a user system.
- A cock for condensation drainage.
- A switchgear enclosed in a special watertight metal casing with switches for automatic or manual pump
operation, an alarm device with sound and light signal, alarm-test buttons and hour-counter for counting
the hours of actual operation of every single pump.
These safety pump sets normally provide for the operation of one pump with subsequent automatic
insertion of the second one for larger consumptions and when, for whatever reason, the plant level of
vacuum goes under the preset value.
The automatic timed inverter, located on the switchboard, accurately alternates the pump start-up, so that
they are both subject to the same mechanical wear.
The switchboard and remote alarm systems operate when the plant level of vacuum is below the set
safety value.

7.71
HORIZONTAL SAFETY PUMP SETS DSO 300V ...

Digital vacuum switch

Switchgear Item 12 40 10

Vacuum pump Pump exclusion

3D drawings are available on vuototecnica.net

Item 09 05 10 valve
Vacuum gauge

Vacuum
cut-off valve
Item 13 07 10

Cock for condensation

drainage Item 13 03 11

Tank 2 Pumps Motor performance Switchgear C L R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSO 300V RVP 40 300 RVP 40 3 ~ 230/400-50Hz DSO 300 97V 1005 1480 G1”1/2 204.8 FB 50 / FC 50
DSO 300V VTL 50/G1 300 VTL 50/G1 3 ~ 230/400-50Hz DSO 300 97V 990 1480 G1”1/2 214.8 FB 50 / FC 50
DSO 300V RVP 60 300 RVP 60 3 ~ 230/400-50Hz DSO 300 97V 1040 1480 G1”1/2 224.8 FB 50 / FC 50
DSO 300V VTL 75/G1 300 VTL 75/G1 3 ~ 230/400-50Hz DSO 300 97V 1040 1480 G1”1/2 259.8 FB 50 / FC 50
DSO 300V RVP 100 300 RVP 100 3 ~ 230/400-50Hz DSO 300 97V 1040 1480 G1”1/2 270.8 FB 50 / FC 50
DSO 300V VTL 105/G1 300 VTL 105/G1 3 ~ 230/400-50Hz DSO 300 97V 1080 1480 G1”1/2 302.0 FB 50 / FC 50
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

HORIZONTAL SAFETY PUMP SETS DSO 500V ...

Digital vacuum switch

Switchgear Item 12 40 10
Pump exclusion
Vacuum pump
valve
Item 09 05 10
Vacuum gauge

Vacuum
cut-off valve
Item 13 08 10

Cock for condensation

drainage Item 13 03 11

Tank 2 Pumps Motor performance Switchgear C L R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSO 500V VTL 50/G1 500 VTL 50/G1 3 ~ 230/400-50Hz DSO 300 97V 1090 1510 G2” 287.8 FB 60 / FC 60
DSO 500V RVP 60 500 RVP 60 3 ~ 230/400-50Hz DSO 300 97V 1130 1510 G2” 297.0 FB 60 / FC 60
DSO 500V VTL 75/G1 500 VTL 75/G1 3 ~ 230/400-50Hz DSO 300 97V 1140 1510 G2” 332.8 FB 60 / FC 60
DSO 500V RVP 100 500 RVP 100 3 ~ 230/400-50Hz DSO 300 97V 1130 1510 G2” 343.3 FB 60 / FC 60
DSO 500V VTL 105/G1 500 VTL 105/G1 3 ~ 230/400-50Hz DSO 300 97V 1180 1510 G2” 375.0 FB 60 / FC 60
DSO 500V RVP 160 500 RVP 160 3 ~ 400/690-50Hz DSO 300 97V 1430 1510 G2” 475.0 FB 60 / FC 60
DSO 500V RVP 200 500 RVP 200 3 ~ 400/690-50Hz DSO 300 97V 1430 1510 G2” 481.0 FB 60 / FC 60
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.72
HORIZONTAL SAFETY PUMP SETS DSO 1000V ...

3D drawings are available on vuototecnica.net

Switchgear Digital vacuum switch
Item 12 40 10 Vacuum gauge

Vacuum pump
Pump exclusion valve
Item 09 05 10

Vacuum cut-off
valve Item 13 09 10

7
Cock for
condensation
drainage
Item 13 03 11

Tank 2 Pumps Motor performance Switchgear C L R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSO 1000V RVP 60 1000 RVP 60 3 ~ 230/400-50Hz DSO 300 97V 1318 1730 G3” 366.8 FC 80
DSO 1000V VTL 75/G1 1000 VTL 75/G1 3 ~ 230/400-50Hz DSO 300 97V 1380 1730 G3” 389.8 FC 80
DSO 1000V RVP 100 1000 RVP 100 3 ~ 230/400-50Hz DSO 300 97V 1298 1730 G3” 396.8 FC 80
DSO 1000V VTL 105/G1 1000 VTL 105/G1 3 ~ 230/400-50Hz DSO 300 97V 1430 1730 G3” 432.0 FC 80
DSO 1000V RVP 160 1000 RVP 160 3 ~ 400/690-50Hz DSO 300 97V 1678 1730 G3” 446.0 FC 80
DSO 1000V RVP 200 1000 RVP 200 3 ~ 400/690-50Hz DSO 300 97V 1678 1730 G3” 452.0 FC 80
DSO 1000V RVP 250 1000 RVP 250 3 ~ 400/690-50Hz DSO 300 97V 1639 1730 G3” 545.2 FC 80
DSO 1000V RVP 300 1000 RVP 300 3 ~ 400/690-50Hz DSO 300 97V 1639 1730 G3” 573.2 FC 80
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.73
VERTICAL PUMP SETS - GENERAL DESCRIPTION

As a standard, these pump sets are built with various capacities and they are composed of:
- A vertical welded sheet steel tank with perfect vacuum seal.
- A rotary vane vacuum pump to be selected according to the required suction
flow rate and level of vacuum.
3D drawings are available on vuototecnica.net

- A digital vacuum switch for adjusting the level of vacuum within which to operate.
- A vacuum gauge for a direct reading of the level of vacuum in the tank.
- Switchgear enclosed in a special metal watertight casing.
- A manual valve for vacuum interception.
- A cock for condensation drainage.
The level of vacuum, preset via the mini vacuum switch is automatically maintained in
the tank. The pump operation can be both continuous or automatic.
The level of vacuum, preset via the mini vacuum switch is automatically maintained in
the tank. The pump operation can be both continuous or automatic. These pump sets
are normally used for interconnecting several vacuum-operated machines and, for safety
reasons, for vacuum handlers since, in case of electricity failure, they allow the vacuum
cups to maintain the grip for an amount of time proportional to the tank capacity.
As for energy consumption, in both cases these pump sets offer many advantages,
since the pump operates only to restore vacuum in the tank within the preset values and
its interventions depend exclusively on the quantity of air that is actually sucked at the
service.

7.74
VERTICAL PUMP SETS DV 150V ...

Vacuum gauge
Vacuum pump Item 09 03 10

3D drawings are available on vuototecnica.net

Switchgear

Digital vacuum switch

Item 12 40 10 Vacuum cut-off
valve Item 13 05 10

Cock for condensation

drainage Item 13 05 10

Tank Pump Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DV 150V VTL 25/FG 150 VTL 25/FG 3 ~ 230/400-50Hz DO 100 97V 730 1600 G1” 103 FB 30 / FC 30
DV 150V VTL 30/FG 150 VTL 30/FG 3 ~ 230/400-50Hz DO 100 97V 730 1600 G1” 107 FB 30 / FC 30
DV 150V VTL 35/FG 150 VTL 35/FG 3 ~ 230/400-50Hz DO 100 97V 730 1600 G1” 109 FB 30 / FC 30
DV 150V RVP 40 150 RVP 40 3 ~ 230/400-50Hz DO 100 97V 816 1600 G1” 120 FB 30 / FC 30
DV 150V VTL 50/G1 150 VTL 50/G1 3 ~ 230/400-50Hz DO 100 97V 805 1600 G1” 126 FB 30 / FC 30
DV 150V RVP 60 150 RVP 60 3 ~ 230/400-50Hz DO 100 97V 840 1600 G1” 131 FB 30 / FC 30
DV 150V VTL 75/G1 150 VTL 75/G1 3 ~ 230/400-50Hz DO 100 97V 855 1600 G1” 148 FB 30 / FC 30
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

VERTICAL PUMP SETS DV 300V ...

Vacuum gauge
Item 09 03 10

Vacuum pump

Switchgear

Digital vacuum switch

Item 12 40 10 Vacuum cut-off
valve Item 13 08 10

Cock for condensation

drainage Item 13 05 10

Tank Pump Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DV 300V RVP 40 300 RVP 40 3 ~ 230/400-50Hz DO 100 97V 974 1890 G2” 143 FB 60 / FC 60
DV 300V VTL 50/G1 300 VTL 50/G1 3 ~ 230/400-50Hz DO 100 97V 805 1890 G2” 156 FB 60 / FC 60
DV 300V RVP 60 300 RVP 60 3 ~ 230/400-50Hz DO 100 97V 998 1890 G2” 161 FB 60 / FC 60
DV 300V VTL 75/G1 300 VTL 75/G1 3 ~ 230/400-50Hz DO 100 97V 855 1890 G2” 178 FB 60 / FC 60
DV 300V RVP 100 300 RVP 100 3 ~ 230/400-50Hz DO 100 97V 988 1890 G2” 179 FB 60 / FC 60
DV 300V VTL 105/G1 300 VTL 105/G1 3 ~ 230/400-50Hz DO 100 97V 900 1890 G2” 199 FB 60 / FC 60
DV 300V RVP 160 300 RVP 160 3 ~ 400/690-50Hz DO 100 97V 1019 1890 G2” 206 FB 60 / FC 60
DV 300V RVP 200 300 RVP 200 3 ~ 400/690-50Hz DO 100 97V 1019 1890 G2” 209 FB 60 / FC 60
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.75
VERTICAL PUMP SETS DV 500V ...

Vacuum gauge
3D drawings are available on vuototecnica.net

Item 09 03 10

Digital vacuum switch

Item 12 40 10
Vacuum pump

Switchgear
Vacuum
cut-off valve
Item 13 08 10

Cock for condensation

drainage Item 13 05 10

Tank Pump Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DV 500V RVP 160 500 RVP 160 3 ~ 400/690-50Hz DO 100 97V 1146 2220 G2” 343 FB 60 / FC 60
DV 500V RVP 200 500 RVP 200 3 ~ 400/690-50Hz DO 100 97V 1146 2220 G2” 346 FB 60 / FC 60
DV 500V RVP 250 500 RVP 250 3 ~ 400/690-50Hz DO 100 97V 1146 2220 G2” 402 FB 60 / FC 60
DV 500V RVP 300 500 RVP 300 3 ~ 400/690-50Hz DO 100 97V 1146 2220 G2” 416 FB 60 / FC 60
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

VERTICAL PUMP SETS DV 1000V ...

Vacuum gauge
Item 09 03 10

Digital vacuum switch

Item 12 40 10

Vacuum pump

Switchgear Vacuum
7 cut-off valve
Item 13 09 10

Cock for condensation

drainage Item 13 05 10

Tank Pump Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DV 1000V RVP 200 1000 RVP 200 3 ~ 400/690-50Hz DO 100 97V 1334 2480 G3” 384 FC 80
DV 1000V RVP 250 1000 RVP 250 3 ~ 400/690-50Hz DO 100 97V 1334 2480 G3” 451 FC 80
DV 1000V RVP 300 1000 RVP 300 3 ~ 400/690-50Hz DO 100 97V 1334 2480 G3” 465 FC 80
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.76
VERTICAL SAFETY PUMP SETS – GENERAL DESCRIPTION

Safety pump sets have been designed to centralise vacuum in all work environments such as hospitals,
laboratories, etc. where vacuum must be guaranteed 24/7.
They are essentially composed of:
- A vertical welded sheet steel tank with perfect vacuum seal.

3D drawings are available on vuototecnica.net

7.77
VERTICAL SAFETY PUMP SETS DSV 150V ..

Digital vacuum switch Pump exclusion valve

Item 12 40 10
3D drawings are available on vuototecnica.net

Vacuum pump

Vacuum gauge
Item 09 03 10
Switchgear

Vacuum
cut-off valve
Item 13 05 10
Cock for condensation
drainage Item 13 05 10

Tank 2 Pumps Motor performance Switchgear H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSV 150V RVP 15 150 RVP 15 3 ~ 230/400-50Hz DSO 300 97V 1600 G1” 174 FB 30 / FC 30
DSV 150V RVP 21 150 RVP 21 3 ~ 230/400-50Hz DSO 300 97V 1600 G1” 160 FB 30 / FC 30
DSV 150V VTL 25/FG 150 VTL 25/FG 3 ~ 230/400-50Hz DSO 300 97V 1600 G1” 168 FB 30 / FC 30
DSV 150V VTL 30/FG 150 VTL 30/FG 3 ~ 230/400-50Hz DSO 300 97V 1600 G1” 172 FB 30 / FC 30
DSV 150V VTL 35/FG 150 VTL 35/FG 3 ~ 230/400-50Hz DSO 300 97V 1600 G1” 174 FB 30 / FC 30
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

VERTICAL SAFETY PUMP SETS DSV 300V ..

Pump exclusion valve

Digital vacuum switch
Item 12 40 10

Vacuum pump
Vacuum gauge
Item 09 03 10

Switchgear

Vacuum
cut-off valve
Item 13 08 10

Cock for condensation

drainage Item 13 05 10

Tank 2 Pumps Motor performance Switchgear H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSV 300V RVP 40 300 RVP 40 3 ~ 230/400-50Hz DSO 300 97V 1890 G2” 223 FB 60 / FC 60
DSV 300V VTL 50/G1 300 VTL 50/G1 3 ~ 230/400-50Hz DSO 300 97V 1890 G2” 226 FB 60 / FC 60
DSV 300V RVP 60 300 RVP 60 3 ~ 230/400-50Hz DSO 300 97V 1890 G2” 237 FB 60 / FC 60
DSV 300V VTL 75/G1 300 VTL 75/G1 3 ~ 230/400-50Hz DSO 300 97V 1890 G2” 249 FB 60 / FC 60
DSV 300V RVP 100 300 RVP 100 3 ~ 230/400-50Hz DSO 300 97V 1890 G2” 246 FB 60 / FC 60
DSV 300V VTL 105/G1 300 VTL 105/G1 3 ~ 230/400-50Hz DSO 300 97V 1890 G2” 270 FB 60 / FC 60
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.78
VERTICAL SAFETY PUMP SETS DSV 500V ..

Pump exclusion valve

Digital vacuum switch

Item 12 40 10

3D drawings are available on vuototecnica.net

Vacuum pump

Vacuum gauge
Item 09 03 10

Switchgear

Vacuum
cut-off valve
Item 13 08 10
Cock for condensation
drainage Item 13 05 10

Tank 2 Pumps Motor performance Switchgear H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSV 500V RVP 60 500 RVP 60 3 ~ 230/400-50Hz DSO 300 97V 2220 G2” 320 FB 60 / FC 60
DSV 500V VTL 75/G1 500 VTL 75/G1 3 ~ 230/400-50Hz DSO 300 97V 2220 G2” 355 FB 60 / FC 60
DSV 500V RVP 100 500 RVP 100 3 ~ 230/400-50Hz DSO 300 97V 2220 G2” 359 FB 60 / FC 60
DSV 500V VTL 105/G1 500 VTL 105/G1 3 ~ 230/400-50Hz DSO 300 97V 2220 G2” 396 FB 60 / FC 60
DSV 500V RVP 160 500 RVP 160 3 ~ 400/690-50Hz DSO 300 97V 2220 G2” 491 FB 60 / FC 60
DSV 500V RVP 200 500 RVP 200 3 ~ 400/690-50Hz DSO 300 97V 2220 G2” 497 FB 60 / FC 60
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

VERTICAL SAFETY PUMP SETS DSV 1000V ..

Pump exclusion valve

Digital vacuum switch

Item 12 40 10

Vacuum pump

Vacuum gauge
Item 09 03 10
7

Switchgear

Vacuum
cut-off valve
Item 13 09 10

Cock for condensation Pump power outlets

drainage Item 13 05 10

Tank 2 Pumps Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSV 1000V RVP 160 1000 RVP 160 3 ~ 400/690-50Hz DSO 300 97V 1751 2480 G3” 564 FC 80
DSV 1000V RVP 200 1000 RVP 200 3 ~ 400/690-50Hz DSO 300 97V 1751 2480 G3” 570 FC 80
DSV 1000V RVP 250 1000 RVP 250 3 ~ 400/690-50Hz DSO 300 97V 1751 2480 G3” 679 FC 80
DSV 1000V RVP 300 1000 RVP 300 3 ~ 400/690-50Hz DSO 300 97V 1751 2480 G3” 707 FC 80
Note: All RVP pumps .. are equipped as standard with an FC filter .. suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.79
VERTICAL SAFETY PUMP SETS DSV 2000V ..
3D drawings are available on vuototecnica.net

Vacuum
cut-off valve
Item 13 09 10
Pump exclusion valve

Digital vacuum switch

Item 12 40 10

Switchgear
Vacuum pump
Vacuum gauge
Item 09 03 10

Cock for condensation

drainage Item 13 05 10
Pump power outlets

Tank 2 Pumps Motor performance Switchgear C H R Weight Filter Accessories

Item
Litres Mod. Volt item Ø Kg item
DSV 2000V RVP 200 2000 RVP 200 3 ~ 400/690-50Hz DSO 300 97V 1751 2450 G3” 888 FC 80
DSV 2000V RVP 250 2000 RVP 250 3 ~ 400/690-50Hz DSO 300 97V 1751 2450 G3” 996 FC 80
DSV 2000V RVP 300 2000 RVP 300 3 ~ 400/690-50Hz DSO 300 97V 1751 2450 G3” 1040 FC 80
Note: All RVP pumps ... are equipped as standard with an FC filter ... suitable for the size of their suction connection.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.80
SPECIAL PUMP SET PRODUCTS

3D drawings are available on vuototecnica.net

DV300VRVP300FS50BP

DS3V500VRVP100

7.81
SPECIAL PUMP SET PRODUCTS
3D drawings are available on vuototecnica.net

DO50VRVP40

DO500RVP200FS

7.82
SUPPORT FRAMES FOR TWO VACUUM PUMPS
AND SWITCHGEAR
This frame is made with profiled steel and varnished with special
weather-resistant paints.
It is suited for assembling two vacuum pumps and their switchgear.

3D drawings are available on vuototecnica.net

Support for switchgear

Fixing plates for electrical power

outlets for pumps

Fitted for Fitted for

Item Weight 2 Pumps switchgear
Kg Mod. item
00 DSV 16 120 RVP 160 - RVP 200 - RVP 250 - RVP 300 D2V 150 95V
DSO 300 97V

SUPPORT FRAMES FOR TWO VACUUM PUMPS

This frame is made with profiled steel and varnished with special
weather-resistant paints.
It is suited for assembling two vacuum pumps.

Fixing plates for electrical power

outlets for pumps 7

Fitted for
Item Weight 2 Pumps
Kg Mod.
00 DSV 18 117 RVP 160 - RVP 200 - RVP 250 - RVP 300

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.83
SUPPORT FRAMES FOR THREE VACUUM PUMPS
AND SWITCHGEAR
This frame is made with profiled steel and varnished with special
weather-resistant paints.
It is suited for assembling three vacuum pumps and their switchgear.
3D drawings are available on vuototecnica.net

Support for switchgear

Fixing plates for electrical power

outlets for pumps

Fitted for Fitted for

Item Weight 3 Pumps switchgear
Kg Mod. item
00 DSV 20 200 RVP 160 - RVP 200 - RVP 250 - RVP 300 DSO 300 98V

SUPPORT FRAMES FOR THREE VACUUM PUMPS

This frame is made with profiled steel and varnished with special
weather-resistant paints.
It is suited for assembling three vacuum pumps.
Fixing plates for electrical power
outlets for pumps

Fitted for
Item Weight 3 Pumps
Kg Mod.
00 DSV 22 197 RVP 160 - RVP 200 - RVP 250 - RVP 300

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.84
SUPPORTS FOR SWITCHGEAR

3D drawings are available on vuototecnica.net

2 PLATES 50X50XH MM.
WITH Ø 12.5 HOLE

Fitted for
Item Weight A B C D E F G H I switchgear
Kg item
00 DV 16 1.5 300 256 22 300 256 22 3 10 200 DO 100 98V - DO 100 97V
00 DSV 08 5.5 400 380 10 700 502 49 5 10 300 D2V 150 95V - DSO 300 97V
00 DSV 33 7.0 500 480 10 700 602 49 5 10 400 DSO 300 98V - DSV 2000 99V

4 SLOTS

Fitted for
Item Weight A B switchgear
Kg item
00 DSO 07 7.5 850 250 DSO 300 97V
00 DSO 08 9.0 920 430 DSO 300 97V

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.85
VACUUM PUMP AND PUMP SET MANIFOLDS

These manifolds are made to distribute the vacuum generated by the

pumps and pump sets to several services.
They are composed of a varnished steel tubular onto which the
interception valves and the connections to the level of vacuum
3D drawings are available on vuototecnica.net

reading and control devices are installed.

The manifolds described in these pages are standard. Upon request,
they can be supplied with different shapes and sizes.

2 caps G1/4” 5 Manual 2-way E valves

Manual 2-way F valve

A B C F G L M R Manual valve E Manual valve F Weight

Item
Ø Ø item item Kg
COLL 01 03 35 70 40 65 G1/2” 350 100 G1/4” 13 01 11 13 03 10 1.75
COLL 01 04 35 70 40 65 G3/4” 350 100 G3/8” 13 02 11 13 04 10 1.90
COLL 01 05 35 70 40 65 G1” 350 100 G3/8” 13 02 11 13 05 10 2.00
COLL 01 06 40 85 60 85 G1”1/4 420 160 G1/2” 13 03 11 13 06 10 2.50
COLL 01 07 40 85 60 85 G1”1/2 420 160 G1/2” 13 03 11 13 07 10 2.60

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.86
VACUUM PUMP AND PUMP SET MANIFOLDS

4 caps G1/4” 8 Manual 2-way valves

3D drawings are available on vuototecnica.net

A B C F G H L M R Manual valve Weight
Item
Ø Ø item Kg
COLL 02 03 37.5 125 40 65 G1/2” 74 450 97 G1/4” 13 01 11 2.5
COLL 02 05 37.5 125 40 66 G1” 84 450 96 G3/8” 13 02 11 2.7
COLL 02 07 37.5 125 60 94 G1”1/2 108 450 127 G1/2” 13 03 11 2.9

4 Manual 2-way valves 2 caps G1/4”

A B C F G H L M R Manual valve Weight

Item
Ø Ø item Kg
COLL 03 03 20 70 30 55 G1/2” 64 250 87 G1/4” 13 01 11 1.2
COLL 03 05 20 70 40 66 G1” 84 250 96 G3/8” 13 02 11 1.4
COLL 03 07 20 70 60 94 G1”1/2 108 250 127 G1/2” 13 03 11 1.5

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
7.87
MINI PUMP SET SWITCHGEAR

The mini pump set switchgear is enclosed in a special plastic casing. It can automatically manage a vacuum pump with a maximum power of
5.5 KW with AC and can also maintain the level of vacuum in the tank, set with the digital vacuum switch installed on the control panel.
It is equipped with a remote control switch with thermal protection, a fuse, digital vacuum switch, a transformer for low voltage auxiliary
command, a selector for automatic or manual pump operation, an emergency button and signalling lamps.
3D drawings are available on vuototecnica.net

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
DO 06 98V 1 1 ~ 230-50Hz 5.5 2
DO 06 97V 1 3 ~ 230/400-50Hz 5.5 2

SWITCHGEAR
FOR PUMP SETS WITH ONE PUMP
The pump set switchgear is enclosed in a special watertight metal casing and can manage a vacuum pump with a power up to 7.5 KW as well
as maintain the level of vacuum in the tank, set with the digital vacuum switch.
It is equipped with a remote control switch with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line
switch, a changeover switch for the automatic or manual pump operation, an easily-programmable digital vacuum switch suitable for setting
and controlling all vacuum functions, an hour-counter for measuring the actual pump operation time and signalling lamps.

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
DO 100 98V 1 1 ~ 230-50Hz 7.5 8
DO 100 97V 1 3 ~ 230/400-50Hz 7.5 8

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.88
SWITCHGEAR FOR PUMP SETS WITH TWO PUMPS

The pump set switchgear is enclosed in a special watertight metal casing and can manage two vacuum pumps, each with a power up to 7.5
KW as well as maintain the level of vacuum in the tank, set with the digital vacuum switch.
It is equipped with two remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply,
a line switch, a changeover switches for the automatic or manual pump operation, an easily-programmable digital vacuum switch suitable for

3D drawings are available on vuototecnica.net

setting and controlling all vacuum functions, two hour-counters for measuring the actual pump operation time and signalling lamps.

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
D2V 150 95V 2 3 ~ 230/400-50Hz 7.5 cad. 24

SWITCHGEAR
FOR SAFETY PUMP SET WITH 2 PUMPS
The pump set switchgear, is enclosed in a special watertight metal casing andautomatically manages two vacuum pumps, each with a power up to 7.5
KW and maintains the level of vacuum in the tank, set with the two easily-programmable digital vacuum switches, suitable for setting and controlling all
vacuum functions.
It is equipped with two remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line
switch, a changeover switches for the automatic or manual pump operation, two digital vacuum switches, two hour-counters for measuring the actual
pump operation time, an alarm siren with acoustic and lit signalling, a key selector for any necessary exclusion of the siren, test buttons and signalling
lamps.
The switchgear is normally provides for the operation of one pump with subsequent automatic insertion of the second one for larger consumptions and
when, for whatever reason, the plant level of vacuum goes under the preset value.
The automatic timed inverter precisely alternates priority pump start-up of the services so that they are subjected to equal mechanical wear. The
switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value.

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
DSO 300 97V 2 3 ~ 230/400-50Hz 7.5 cad. 27

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.89
SWITCHGEAR FOR SAFETY PUMP SETS WITH THREE PUMPS

The pump set switchgear, is enclosed in a special watertight metal casing andautomatically manages three vacuum pumps, each with a power up to 7.5 KW
and maintains the level of vacuum in the tank, set with the two easily-programmable digital vacuum switches, suitable for setting and controlling all vacuum
functions.
It is equipped with three remote control switches with thermal protection, fuses, a transformer for low voltage auxiliary command power supply, a line switch, a
3D drawings are available on vuototecnica.net

changeover switches for the automatic or manual pump operation, three digital vacuum switches, two hour-counters for measuring the actual pump operation
time, an alarm siren with acoustic and lit signalling, a key selector for any necessary exclusion of the siren, test buttons and signalling lamps. The switchgear is
normally provides for the operation of one pump with subsequent automatic insertion of the other two for larger consumptions and when, for whatever reason,
the plant level of vacuum goes under the preset value.
The automatic timed inverter precisely alternates priority pump start-up of the services so that they are subjected to equal mechanical wear. The switchboard
and remote alarm systems operate when the plant level of vacuum is below the set safety value.

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
DSO 300 98V 3 3 ~ 230/400-50Hz 7.5 cad. 29

SWITCHGEAR
FOR SAFETY PUMP SET WITH FOUR PUMPS
The safety pump set switchgear is enclosed in a special watertight metal casing and it automatically manages four vacuum pumps, each with
a power up to 7.5 KW, and maintains the level of vacuum in the tank, set with the two easily-programmable digital vacuum switches, suitable
for setting and controlling all vacuum functions. It is equipped with four remote control switches with thermal protection, fuses, a transformer
for low voltage auxiliary command power supply, a line switch, a changeover switches for the automatic or manual pump operation, two digital
vacuum switches, four hour-counters for measuring the actual pump operation time, an alarm siren with acoustic and lit signalling, a key selector
for any necessary exclusion of the siren, test buttons and signalling lamps.
These switchgears normally provide for the operation of two pumps and the subsequent automatic insertion of the other two for larger
consumptions and when, for whatever reason, the plant level of vacuum goes below the preset value.
The automatic timed inverter precisely alternates priority pump start-up of the services so that they are subjected to equal mechanical wear.
The switchboard and remote alarm systems operate when the plant level of vacuum is below the set safety value.

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
DSV 2000 99V 4 3 ~ 230/400-50Hz 7.5 cad. 29.5

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.90
SWITCHGEAR FOR SINGLE PUMP

The need to use the same vacuum pump in various spots in the work environment,
such as, for example, a shipyard, has led us to creating this mobile switchgear that
allows for polarity reversal in presence of current, as well as for time setting pump
operation and the automatic start-up restoration in case of accidental black-out.

3D drawings are available on vuototecnica.net

The switchgear is enclosed in a special watertight metal casing and it is composed
of fuses, remote control switches with thermal protection and a transformer for low
voltage auxiliary command power supply. The following are instead installed on the
casing lid:
- A line switch with indicator light
- A changeover switch for pump start-up with indicator light
- A changeover switch for polarity reversal
- An emergency button
- A timer for setting the duration of pump operation
- An hour-counter for counting the actual pump operation time
- A malfunction warning light.
This switchgear is supplied in special metal watertight casing and can manage pumps
with power up to 7.5 Kw.

Quantity of pumps Motor performance Max pump power Weight

Item
No. Volt Kw Kg
DO 100 94 1 3 ~ 230/400-50Hz 7.5 8.0

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.91
SWITCHGEAR EQUIPPED WITH TOUCH SCREEN OPERATOR PANEL AND
PLC FOR PUMP SETS AND SAFETY PUMP SETS WITH TWO OR MORE PUMP
The new electrical equipment consists of a touch screen, which is a special electronic device that is the result of combining a screen and a digitizer that
allow the user to interact with a graphical interface using their fingers or specific objects.
The touch screen operator panels installed on our Pump sets are human machine interface systems, or rather devices that allow people to control our
equipment very easily.

3D drawings are available on vuototecnica.net

The electrical panel contains command and control equipment, collects the digital signals coming from the vacuum switch to power the vacuum
pumps when necessary and is designed for a single-phase 230 Vac 50 Hz and three-phase 400 Vac 50 Hz power supply with an IP 54 protection rating.
Inside is a PLC that manages all the control logics for manual and automatic operation.

PUMP SET SETTINGS

VACUUM SWITCH CONFIGURATOR

SCHEDULED MAINTENANCE

ALARM MESSAGES

PRODUCTS

VACUUM TREND GRAPH

LANGUAGES

The many advantages:

- New Design
- Alarm signalling with acoustic-visual siren
- Easy, intuitive programming
- System maintenance messages
- Vacuum level adjustable from panel
- Pump alarm-maintenance reports 7
- Energy-saving display switch-off
- Translatable into 5 languages
- Remote control (optional)
The pump set is designed to operate vacuum pumps in manual or
automatic mode thanks to our precise, reliable digital vacuum switches,
which can be easily programmed via the operator panel.
Bright displays with a wide viewing angle provide an excellent overview of
the status of the machine as a whole and of all systems thanks to the 7”-
10” touch screen operator panels with graphic interface.
We have included a real-time vacuum trend page with a graph.
Alarm messages indicate the type of alarm that has occurred on the panel
for immediate and simplified troubleshooting.
System maintenance messages are displayed during the correct
maintenance period.
(Possibility of displaying our products via a Qr code search). Remote
control (optional) lets you monitor the values of our equipment, as well as
making it possible to operate remotely without additional modules.

7.91 -1
SWITCHGEAR EQUIPPED WITH
TOUCH SCREEN OPERATOR PANEL AND PLC FOR PUMP SETS
Pump set switchgear with a 7” touch screen operator panel is able to automatically manage
a vacuum pump with a maximum power of 7.5 KW in AC and can also maintain the level of
vacuum in the tank.All settings are managed by the Operator Panel and PLC. All settings are
managed from the Operator Panel and PLC.
3D drawings are available on vuototecnica.net

Quantity of pumps Motor performance Max pump power Weight

Art.
No. Volt Kw Kg
DO 100 98V PLC 1 1 ~ 230-50Hz 7.5 8
DO 100 97V PLC 1 3 ~ 230/400-50Hz 7.5 8

SWITCHGEAR EQUIPPED WITH TOUCH SCREEN OPERATOR PANEL AND PLC

FOR SAFETY PUMP SETS WITH 2 PUMPS
Safety pump set switchgear with a 10” touch screen operator panel is able to automatically manage two vacuum
pumps with a maximum power of 7.5 KW AC and maintains the level of vacuum in the tank.
All settings are managed from the Operator Panel and PLC.

Quantity of pumps Motor performance Max pump power Weight

Art.
No. Volt Kw Kg
DSO 300 97V PLC 2 3 ~ 230/400-50Hz 7.5 cad. 26

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
7.92 -1
VACUUM PUMP QUESTIONNAIRE Company

For a correct dimensioning and selection of a vacuum pump, it Address

is important to know and assess the use to be made as well as
the working environment in which it will operate.
For this reason, we kindly ask you to fill in this form and send it Post code / City Country

3D drawings are available on vuototecnica.net

back to us via e-mail or fax.
We will suggest the best vacuum pump to solve your problem.
E-mail: [email protected] Contact person:
Fax: +39 039 5320015

Telephone Fax

E-mail

1) In which industry sector will the pump be used?

Plastic Packaging Woodworking Cosmetics

CD/DVD Glass/Solar Marble/Stone Automotive
Electronics Graphic arts Medical/Pharmaceutical Ceramics/Porcelain
Food Bottling Other sectors

2) Which service should the vacuum pump be designed for?

Handling with vacuum cups Vacuum clamping

Degassing of silicone or resin mixtures Vacuum packaging
Moulding of plastics/rubbers/resins/aluminium
Emptying containers: Volume/L Time required s Max vacuum mbar abs.
Other use

3) Where will the vacuum pump be located?

Inside a plant or mobile unit

Outside a plant or mobile unit
Height above sea level of the place where the pump is installed m
Temperature of the work environment: min °C max °C Humidity %.

4) Type of sucked fluid?

Dry air Moist air Air with water Air with oil vapours
Aggressive gases Air with abrasive dust
Fluid temperature °C
7

5) Required flow rate?

m3/h Nl/min cfm

6) Required level of vacuum?

mbar abs. mmHg -KPa

7) Use of the vacuum pump and related work cycles

Daily duration: 8 hours 16 hours 24 hours Hours?

Number of work cycles/hour Intermittency times: ON/ s OFF/s
Are there strong level of vacuum oscillations in the plant? Yes No
If yes, within what values? min mbar max mbar
%

7.93
VACUUM PUMP QUESTIONNAIRE

8) When the pump stops, does the air return in the vacuum system need to be prevented?

Yes No
The seal is ensured by the check valves, whose use is:
3D drawings are available on vuototecnica.net

- Mandatory, on lubricated vacuum pumps

- Optional, on dry vacuum pumps
Note: Check valves are integrated onto oil-bath vacuum pumps on the RVP series.

9) Vacuum holding time

Does the vacuum need to be maintained for a specific time? (for example, to support a suspended load with vacuum cups, in case of
a blackout) Yes No
If yes, for how long? s

10) Vacuum tanks

Required volume L Recommended volume L Available volume L

11) Purchase prospects

Single request No. pumps/year Required delivery:

12) In the event of vacuum pump replacement

Model used to present: Flow rate m3/h Level of vacuum mbar

Brand
Electrical power: Single-phase Volt 230-50 Hz Other Volt Hz
Three-phase Volt 230/400-50 Hz Other Volt Hz

13) Contact

Do you wish to be called back? Yes No

Are you interested in a visit? Yes No If yes, what date/time?

7
%

7.94
VACUUM GENERATORS AND PNEUMATIC PUMP SETS

TABLE REGARDING THE QUANTITY OF AIR SUCKED BY GENERATORS, AT DIFFERENT LEVELS OF VACUUMS PG. 8.01 ÷ 8.02
TABLE REGARDING VACUUM GENERATOR EVACUATION TIME, AT DIFFERENT LEVELS OF VACUUMS PG. 8.03 ÷ 8.04

3D drawings are available on vuototecnica.net

SINGLE-STAGE VACUUM GENERATORS 15 01 10, 15 01 10 LP and 15 01 15 LP PG. 8.05 ÷ 8.06
SINGLE-STAGE VACUUM GENERATOR 15 03 10 PG. 8.07 ÷ 8.08
SINGLE-STAGE VACUUM GENERATORS 15 05 08 SX and 15 05 10 SX PG. 8.09 ÷ 8.10
SINGLE-STAGE VACUUM GENERATOR 15 07 10 SX PG. 8.11 ÷ 8.12
SINGLE-STAGE VACUUM GENERATORS VG 03, VG 03 LP and VG 05 LP PG. 8.13 ÷ 8.14
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR 15 02 10, 15 02 10 LP and 15 02 15 LP PG. 8.15 ÷ 8.16
SINGLE-STAGE VACUUM GENERATOR WITH EJECTOR 15 04 10 PG. 8.17 ÷ 8.18
SINGLE-STAGE VACUUM GENERATOR WITH EJECTOR 15 06 08 SX and 15 06 10 SX PG. 8.19 ÷ 8.20
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR FVG 3 and FVG 5 PG. 8.21 ÷ 8.22
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR FVG 8 and FVG 12 PG. 8.21-1 ÷ 8.22-1
IN-LINE SINGLE-STAGE VACUUM GENERATOR PVP 1 PG. 8.23 ÷ 8.24
IN-LINE SINGLE-STAGE VACUUM GENERATORS GV 1, GV 2 and GV 3 PG. 8.25 ÷ 8.26
SINGLE-STAGE VACUUM GENERATOR PVP 05 PG. 8.27 ÷ 8.28
SINGLE-STAGE VACUUM GENERATOR PVP 2 PG. 8.29 ÷ 8.30
SINGLE-STAGE VACUUM GENERATOR PVP 3 PG. 8.31 ÷ 8.32
SINGLE-STAGE VACUUM GENERATORS PVP 2 M, PVP 2 MM1, PVP 2 MM2 and PVP 2 MM3 PG. 8.33 ÷ 8.34
SINGLE-STAGE VACUUM GENERATORS PVP 7 SX / SXLP, PVP 14 SX / SXLP and PVP 18 SX / SXLP PG. 8.35 ÷ 8.36
ACCESSORIES FOR SINGLE-STAGE VACUUM GENERATORS:
- PNEUMATIC COAXIAL SHUTTER VALVES PG. 8.37
- PNEUMATIC SLEEVE VALVE PG. 8.37
FIXING SUPPORTS FOR SINGLE-STAGE VACUUM GENERATORS PG. 8.38 ÷ 8.39
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 3 and MSVE 5 PG. 8.40 ÷ 8.41
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 8 and MSVE 12 PG. 8.42 ÷ 8.43
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 20 PG. 8.44 ÷ 8.45
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS, SERIES MSVE PG. 8.45-1 ÷ 8.47-1
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS SERIES AVG - GENERAL DESCRIPTION PG. 8.46
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS AVG 18 and AVG 25 PG. 8.47 ÷ 8.48
ACCESSORIES AND SPARE PARTS FOR SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS, SERIES AVG PG. 8.49 ÷ 8.50
MULTI-STAGE VACUUM GENERATORS - GENERAL DESCRIPTION PG. 8.51
MULTI-STAGE VACUUM GENERATORS M 3 and M 7 PG. 8.52 ÷ 8.53
MULTI-STAGE VACUUM GENERATORS M 10, M 14 and M 18 PG. 8.54 ÷ 8.55
MULTI-STAGE VACUUM GENERATORS M 3 SSX and M 7 SSX PG. 8.56 ÷ 8.57
MULTI-STAGE VACUUM GENERATORS M 10 SSX, M 14 SSX and M 18 SSX PG. 8.58 ÷ 8.59
FIXING SUPPORTS FOR MULTI-STAGE VACUUM GENERATORS, SERIES M PG. 8.60
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS SERIES MVG - GENERAL DESCRIPTION PG. 8.61
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MVG 3 and MVG 7 PG. 8.62 ÷ 8.63
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MVG 10 and MVG 14 PG. 8.64 ÷ 8.65
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS, SERIES MVG PG. 8.66 ÷ 8.68
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS SERIES GVMM - GENERAL DESCRIPTION PG. 8.69
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS, GVMM 3 and GVMM 7 PG. 8.70 ÷ 8.71
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS, GVMM 10 and GVMM 14 PG. 8.72 ÷ 8.73
MULTI-STAGE, MULTI-FUNCTION AND MODULAR INTERMEDIATE VACUUM MODULES SERIES MI - GENERAL DESCRIPTION PG. 8.74
INTERMEDIATE VACUUM MODULES MI 3 and MI 7 PG. 8.75 ÷ 8.76
INTERMEDIATE VACUUM MODULES MI 10 and MI 14 PG. 8.77 ÷ 8.78
ACCESSORIES AND SPARE PARTS FOR VACUUM GENERATORS AND MODULES SERIES GVMM and MI PG. 8.79 ÷ 8.81
MODULAR VACUUM SYSTEMS SET-UP PG. 8.82
MULTI-STAGE VACUUM GENERATORS PVP 12 MX / MXLP PG. 8.83 ÷ 8.84
MULTI-STAGE VACUUM GENERATORS PVP 25 MX / MXLP PG. 8.85 ÷ 8.86 8
MULTI-STAGE VACUUM GENERATORS PVP 40 M / MLP, PVP 70 M / MLP and PVP 100 M / MLP PG. 8.87 ÷ 8.88
MULTI-STAGE VACUUM GENERATORS PVP 140 M / MLP, PVP 170 M / MLP and PVP 200 M / MLP PG. 8.89 ÷ 8.90
MULTI-STAGE VACUUM GENERATORS PVP 250 M / MLP and PVP 300 M / MLP PG. 8.91 ÷ 8.92
VACUUM GENERATORS ACCESSORIES PVP 40 M / MLP ÷ PVP 300 M / MLP PG. 8.93 ÷ 8.94
MULTI-STAGE VACUUM GENERATORS PVP 25 MDX / MDXLP, PVP 35 MDX / MDXLP and PVP 50 MDX / MDXLP PG. 8.95 ÷ 8.96
MULTI-STAGE VACUUM GENERATORS PVP 60 MDX / MDXLP and PVP 75 MDX / MDXLP PG. 8.97 ÷ 8.98
VACUUM GENERATORS ACCESSORIES PVP 25 MDX / MDXLP ÷ PVP 75 MDX / MDXLP PG. 8.99 ÷ 8.100
SILENCERS PG. 8.101
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 150 MD / MDLP ÷ PVP 750 MD / MDLP
GENERAL DESCRIPTION PG. 8.102
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 150 MD / MDLP and PVP 300 MD / MDLP PG. 8.103 ÷ 8.104
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 450 MD / MDLP and PVP 600 MD / MDLP PG. 8.105 ÷ 8.106
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 750 MD / MDLP PG. 8.107 ÷ 8.108
VACUUM GENERATORS ACCESSORIES PVP 150 MD / MDLP ÷ PVP 750 MD / MDLP PG. 8.109 ÷ 8.110
ADJUSTABLE CONVEYOR VACUUM GENERATORS PVR 25 and PVR 50 PG. 8.111 ÷ 8.112
VACUUM GENERATORS AND PNEUMATIC PUMP SETS

ADJUSTABLE CONVEYOR VACUUM GENERATORS PVR 100 and PVR 200 PG. 8.113 ÷ 8.114
CARTRIDGE VACUUM GENERATORS PVR 1 and PVR 4 PG. 8.115
3D drawings are available on vuototecnica.net

CARTRIDGE VACUUM GENERATOR PVR 3 OT PG. 8.116

CONVEYOR VACUUM GENERATOR PVR 25 MS, WITH SUPPORT FOR FASTENING TO VACUUM CUPS PG. 8.117
ACCESSORIES AND SPARE PARTS FOR VACUUM GENERATOR PVR 25 MS PG. 8.118
ACCESSORIES FOR ADJUSTABLE CONVEYOR VACUUM GENERATORS PG. 8.119
FLOW GENERATORS VACUUM JET CX 7 and CX 10 PG. 8.120 ÷ 8.121
FLOW GENERATORS VACUUM JET CX 13 and CX 19 PG. 8.122 ÷ 8.123
FLOW GENERATORS VACUUM JET CX 25, CX 38 and CX 50 PG. 8.124 ÷ 8.125
MINI PNEUMATIC PUMP SETS DOP 06 and DOP 10 PG. 8.126
MINI PNEUMATIC PUMP SETS DOP 20 PG. 8.127
PNEUMATIC PUMP SETS DOP 25 PG. 8.128
PNEUMATIC PUMP SETS DOP 50 PG. 8.129
PNEUMATIC PUMP SETS DOP 100 PG. 8.130
PNEUMATIC PUMP SETS DOP 150 PG. 8.131
PNEUMATIC PUMP SETS DOP 300 PG. 8.132
PNEUMATIC DEVICES FOR THE POWER SUPPLY OF MINI PNEUMATIC PUMP SETS DOP 06, DOP 10 and DOP 20 PG. 8.133
PNEUMATIC DEVICES FOR THE POWER SUPPLY OF PNEUMATIC PUMP SETS DOP 50 and DOP 100 PG. 8.134
PNEUMATIC DEVICES FOR THE POWER SUPPLY OF PNEUMATIC PUMP SETS DOP 150 and DOP 300 PG. 8.134
SPECIAL PRODUCTS FOR VACUUM GENERATORS PG. 8.135

8
TABLE REGARDING THE QUANTITY OF AIR SUCKED BY GENERATORS,
AT DIFFERENT LEVELS OF VACUUMS

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different levels of vacuums (-KPa)
Generator
Item Supp. press. Air consumption at optimal supply pressure Max vacuum
bar Nl/s 0 10 20 30 40 50 60 70 80 -KPa
15 01 10 6 0.9 0.80 0.66 0.61 0.55 0.44 0.29 0.19 0.09 --- 85
15 01 10 LP 4 1.2 0.83 0.67 0.63 0.56 0.49 0.41 0.34 0.18 0.08 85
15 01 15 LP 4 2.2 1.38 1.22 1.11 1.00 0.90 0.69 0.44 0.30 0.16 85
15 02 10 6 0.9 0.80 0.66 0.61 0.55 0.44 0.29 0.19 0.09 --- 85
15 02 10 LP 4 1.2 0.83 0.67 0.63 0.56 0.49 0.41 0.34 0.18 0.08 85
15 02 15 LP 4 2.2 1.39 1.22 1.11 1.00 0.90 0.69 0.44 0.30 0.16 85
15 03 10 6 1.6 1.39 1.30 1.15 1.00 0.89 0.77 0.69 0.44 0.04 85
15 04 10 6 1.6 1.39 1.30 1.15 1.00 0.89 0.77 0.69 0.44 0.04 85
15 05 08 SX 3.5 4.3 2.44 2.27 2.11 1.94 1.72 1.46 0.98 0.50 0.04 90
15 05 10 SX 3.5 5.5 3.47 3.24 2.86 2.49 2.22 1.92 1.72 1.20 0.65 90
15 06 08 SX 3.5 4.3 2.44 2.27 2.11 1.94 1.72 1.46 0.98 0.50 0.04 90
15 06 10 SX 3.5 5.5 3.47 3.24 2.86 2.49 2.22 1.92 1.72 1.20 0.65 90
15 07 10 SX 3.5 8.5 5.55 5.00 4.44 4.16 3.83 3.00 1.97 1.56 0.85 90
VG 03 6 0.9 0.80 0.66 0.61 0.55 0.44 0.29 0.19 0.09 --- 85
VG 03 LP 4 1.2 0.83 0.67 0.63 0.56 0.49 0.41 0.34 0.18 0.08 85
VG 05 LP 4 2.2 1.39 1.22 1.11 1.00 0.90 0.69 0.44 0.30 0.16 85
FVG 3 4 1.2 0.83 0.67 0.63 0.56 0.49 0.41 0.34 0.18 0.08 85
FVG 5 4 2.2 1.39 1.22 1.11 1.00 0.90 0.69 0.44 0.30 0.16 85
GV 1 5 0.45 0.27 0.23 0.20 0.17 0.13 0.06 0.05 0.03 --- 85
GV 2 5 0.45 0.27 0.23 0.20 0.17 0.13 0.06 0.05 0.03 --- 85
GV 3 5 0.45 0.27 0.23 0.20 0.17 0.13 0.06 0.05 0.03 --- 85
PVP 05 6 0.5 0.13 0.11 0.10 0.08 0.06 0.03 0.02 0.01 --- 82
PVP 1 5 0.45 0.27 0.25 0.22 0.18 0.12 0.07 0.06 0.03 --- 85
PVP 2 6 0.9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 --- 85
PVP 2 M 6 0.9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 --- 85
PVP 2 MM1 6 0.9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 --- 85
PVP 2 MM2 6 0.9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 --- 85
PVP 2 MM3 6 0.9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 --- 85
PVP 3 6 1.3 1.03 0.82 0.72 0.61 0.41 0.24 0.15 0.08 --- 85
PVP 7 SX 6 3.2 2.58 2.38 2.19 2.02 1.44 0.97 0.86 0.54 0.05 85
PVP 7 SXLP 3 4.5 2.44 2.25 2.07 1.91 1.42 0.95 0.84 0.52 0.04 88
PVP 14 SX 6 4.8 3.75 3.46 3.19 2.95 2.19 1.47 1.29 0.80 0.07 85
PVP 14 SXLP 3 6.9 3.77 3.48 3.20 2.96 2.20 1.48 1.31 0.82 0.07 88
PVP 18 SX 6 6.4 5.00 4.62 4.25 3.93 2.92 1.97 1.75 1.10 0.10 85
PVP 18 SXLP 3 8.6 4.86 4.48 4.12 3.80 2.82 1.90 1.68 1.05 0.09 88
MSVE 3 4 1.2 0.83 0.67 0.63 0.56 0.49 0.41 0.34 0.18 0.08 85
MSVE 5 4 2.2 1.39 1.22 1.11 1.00 0.90 0.69 0.44 0.30 0.16 85
MSVE 8 3.5 4.3 2.44 2.27 2.11 1.94 1.72 1.46 0.98 0.50 0.04 90
MSVE 12 3.5 5.5 3.47 2.88 2.72 2.50 2.27 1.83 1.16 0.60 0.05 90
MSVE 20 4 8.0 5.55 5.00 4.44 4.16 3.83 3.00 1.97 1.56 0.85 90
AVG 18 6 6.4 4.83 4.58 4.04 3.58 2.72 1.90 1.68 1.07 0.10 85 8
AVG 25 6 9.6 7.00 6.63 5.86 5.18 3.94 2.76 2.44 1.54 0.15 85
M3 5 0.8 1.00 0.83 0.61 0.34 0.18 0.12 0.10 0.07 0.03 85
M7 5 1.4 1.72 1.28 0.89 0.50 0.37 0.27 0.16 0.11 0.05 85
M 10 5 1.9 2.61 2.00 1.55 0.80 0.64 0.50 0.29 0.19 0.09 85
M 14 5 2.5 3.50 2.33 1.72 1.00 0.89 0.67 0.35 0.24 0.11 85
M 18 5 3.6 5.00 3.50 2.78 2.02 1.02 0.75 0.44 0.30 0.14 85
M 3 SSX 5 0.8 1.00 0.83 0.61 0.34 0.18 0.12 0.10 0.07 0.03 85
M 7 SSX 5 1.4 1.72 1.28 0.89 0.50 0.37 0.27 0.16 0.11 0.05 85
M 10 SSX 5 1.9 2.61 2.00 1.55 0.80 0.64 0.50 0.29 0.19 0.09 85
M 14 SSX 5 2.5 3.50 2.33 1.72 1.00 0.89 0.67 0.35 0.24 0.11 85
M 18 SSX 5 3.6 5.00 3.50 2.78 2.02 1.02 0.75 0.44 0.30 0.14 85

8.01
TABLE REGARDING THE QUANTITY OF AIR SUCKED BY GENERATORS,
AT DIFFERENT LEVELS OF VACUUMS
3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different levels of vacuums (-KPa)

Generator
Item Supp. press. Air consumption at optimal supply pressure Max vacuum
bar Nl/s 0 10 20 30 40 50 60 70 80 -KPa
MVG 3 5 0.8 0.89 0.69 0.41 0.23 0.18 0.12 0.10 0.07 0.03 85
MVG 7 5 1.3 1.83 1.44 1.11 0.63 0.41 0.25 0.16 0.11 0.05 85
MVG 10 5 1.7 2.55 1.85 1.30 0.75 0.64 0.48 0.30 0.20 0.09 85
MVG 14 5 2.1 3.40 2.45 1.84 1.05 0.88 0.61 0.36 0.24 0.11 85
GVMM 3 5 0.8 0.83 0.66 0.38 0.20 0.16 0.11 0.09 0.06 0.02 85
GVMM 7 5 1.3 1.78 1.30 0.98 0.56 0.44 0.29 0.20 0.14 0.06 85
GVMM 10 5 1.7 2.52 2.00 1.66 0.97 0.56 0.40 0.22 0.16 0.07 85
GVMM 14 5 2.1 3.35 2.42 1.84 0.99 0.80 0.58 0.34 0.22 0.10 85
MI 3 5 0.8 0.83 0.66 0.38 0.20 0.16 0.11 0.09 0.06 0.02 85
MI 7 5 1.3 1.78 1.30 0.98 0.56 0.44 0.29 0.20 0.14 0.06 85
MI 10 5 1.7 2.52 2.00 1.66 0.97 0.56 0.40 0.22 0.16 0.07 85
MI 14 5 2.1 3.35 2.42 1.84 0.99 0.80 0.58 0.34 0.22 0.10 85
PVP 12 MX 6 1.5 5.80 4.14 2.76 1.38 0.98 0.78 0.59 0.41 0.23 90
PVP 12 MXLP 3 2.3 5.00 2.27 1.66 1.05 0.88 0.77 0.64 0.42 0.22 86
PVP 25 MX 6 3.0 8.61 6.15 4.10 2.05 1.46 1.17 0.88 0.61 0.35 90
PVP 25 MXLP 3 4.5 9.44 3.77 2.77 1.72 1.58 1.36 1.11 0.72 0.37 86
PVP 40 M 6 3.2 11.6 8.32 5.55 2.77 1.98 1.58 1.19 0.83 0.47 90
PVP 40 MLP 3 4.4 11.4 5.42 3.45 2.19 2.03 1.72 1.34 0.95 0.54 88
PVP 70 M 6 6.6 22.2 15.8 10.5 5.29 3.77 3.02 2.27 1.58 0.90 90
PVP 70 MLP 3 8.9 20.3 9.65 6.15 3.88 3.61 3.05 2.36 1.66 0.94 88
PVP 100 M 6 9.8 30.0 21.4 14.2 7.14 5.10 4.08 3.06 2.14 1.22 90
PVP 100 MLP 3 13.3 26.4 12.5 8.00 5.07 4.70 4.00 3.10 2.20 1.25 88
PVP 140 M 6 13.0 42.2 30.1 20.1 10.0 7.18 5.74 4.31 3.02 1.72 90
PVP 140 MLP 3 17.8 38.3 18.3 11.6 7.37 6.84 5.80 4.50 3.20 1.80 88
PVP 170 M 6 16.3 50.5 36.1 24.0 12.0 8.59 6.87 5.17 3.61 2.06 90
PVP 170 MLP 3 22.2 45.8 21.8 13.8 8.81 8.18 6.94 5.39 3.82 2.16 88
PVP 200 M 6 19.4 55.5 39.6 26.4 13.2 9.44 7.55 5.68 3.97 2.27 90
PVP 200 MLP 3 26.6 52.8 25.2 16.0 10.1 9.44 8.00 6.20 4.40 2.50 88
PVP 250 M 6 24.0 77.7 55.5 37.0 18.5 13.2 10.5 7.90 5.50 3.10 90
PVP 250 MLP 3 33.6 69.4 34.0 23.5 14.0 11.5 9.80 7.60 5.30 3.00 88
PVP 300 M 6 29.0 88.8 63.4 42.3 21.1 15.1 12.0 9.10 6.35 3.63 90
PVP 300 MLP 3 39.3 83.3 41.5 27.5 17.0 14.5 11.4 8.80 6.10 3.40 88
PVP 25 MDX 6 3.2 11.9 8.5 5.7 2.8 2.0 1.6 1.2 0.8 0.5 90
PVP 25 MDXLP 3 4.4 9.7 4.7 3.5 2.2 2.0 1.7 1.4 1.0 0.6 88
PVP 35 MDX 6 4.8 15.8 11.3 7.5 3.8 2.7 2.1 1.6 1.1 0.6 90
PVP 35 MDXLP 3 6.5 13.0 6.2 4.7 3.0 2.7 2.3 1.8 1.3 0.7 88
PVP 50 MDX 6 6.5 18.8 13.5 9.0 4.5 3.2 2.6 1.9 1.4 0.7 90
PVP 50 MDXLP 3 8.6 16.1 7.7 5.8 3.7 3.3 2.8 2.2 1.5 0.8 88
PVP 60 MDX 6 8.2 25.5 18.2 12.2 6.1 4.3 3.5 2.6 1.8 1.0 90
PVP 60 MDXLP 3 11.0 19.3 9.3 7.0 4.4 4.0 3.4 2.7 1.9 1.0 88
8 PVP 75 MDX 6 9.8 28.6 20.4 13.6 6.8 4.8 3.9 2.9 2.0 1.2 90
PVP 75 MDXLP 3 13.2 22.5 10.8 8.1 5.1 4.6 3.9 3.1 2.2 1.2 88
PVP 150 MD 6 16.0 55.5 39.6 26.5 13.2 9.4 7.5 5.7 4.0 2.3 90
PVP 150 MDLP 3 22.6 47.2 24.5 15.9 10.3 9.3 7.5 4.7 3.2 1.8 88
PVP 300 MD 6 32.0 111.1 79.4 52.9 26.5 19.9 15.1 11.4 7.9 4.5 90
PVP 300 MDLP 3 45.5 94.4 49.0 31.9 20.7 18.6 15.1 9.3 6.5 3.7 88
PVP 450 MD 6 47.8 161.1 115.0 76.7 38.3 27.4 21.9 16.5 11.5 6.6 90
PVP 450 MDLP 3 65.8 138.8 72.7 46.9 30.5 27.4 22.2 13.8 9.6 5.5 88
PVP 600 MD 6 63.2 208.3 148.8 99.2 49.6 35.4 28.3 21.3 14.9 8.5 90
PVP 600 MDLP 3 87.7 186.1 96.7 62.9 40.8 36.8 29.8 18.5 12.9 6.8 88
PVP 750 MD 6 80.0 250.0 180.0 118.8 59.4 42.8 34.2 25.7 18.0 10.2 90
PVP 750 MDLP 3 110.0 222.2 115.5 75.1 48.8 43.9 35.6 22.0 15.4 8.8 88

8.02
TABLE REGARDING VACUUM GENERATOR EVACUATION TIME,
AT DIFFERENT LEVELS OF VACUUMS

3D drawings are available on vuototecnica.net

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa)
Generator
Item Supp. press. Air consumption at optimal supply pressure Max vacuum
bar Nl/s 10 20 30 40 50 60 70 80 85 -KPa
15 01 10 6 0.9 139 278 472 727 1171 1628 2720 4928 --- 85
15 01 10 LP 4 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
15 01 15 LP 4 2.2 70 160 260 410 620 910 1500 2620 4490 85
15 02 10 6 0.9 139 278 472 727 1171 1628 2720 4928 --- 85
15 02 10 LP 4 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
15 02 15 LP 4 2.2 70 160 260 410 620 910 1500 2620 4490 85
15 03 10 6 1.6 77 154 261 403 649 902 1506 2730 3876 85
15 04 10 6 1.6 77 154 261 403 649 902 1506 2730 3876 85
15 05 08 SX 3.5 4.3 35 75 120 190 290 490 920 1530 2730 90
15 05 10 SX 3.5 5.5 25 54 90 140 220 320 570 980 2012 90
15 06 08 SX 3.5 4.3 35 75 120 190 290 490 920 1530 2730 90
15 06 10 SX 3.5 5.5 25 54 90 140 220 320 570 980 2012 90
15 07 10 SX 3.5 8.5 18 37 62 92 140 210 410 770 1220 90
VG 03 6 0.9 139 278 472 727 1171 1628 2720 4928 --- 85
VG 03 LP 4 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
VG 05 LP 4 2.2 70 160 260 410 620 910 1500 2620 4490 85
FVG 3 4 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
FVG 5 4 2.2 70 160 260 410 620 910 1500 2620 4490 85
GV 1 5 0.45 394 788 1339 2063 3322 4617 7711 13973 19841 85
GV 2 5 0.45 394 788 1339 2063 3322 4617 7711 13973 19841 85
GV 3 5 0.45 394 788 1339 2063 3322 4617 7711 13973 19841 85
PVP 05 6 0.5 786 1572 2678 4126 6644 9210 15420 27870 --- 82
PVP 1 5 0.45 393 786 1336 2057 3312 4605 7690 13935 19787 85
PVP 2 6 0.9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2M 6 0.9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2 MM1 6 0.9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2 MM2 6 0.9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2 MM3 6 0.9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 3 6 1.3 104 207 353 544 857 1217 2033 3684 5232 85
PVP 7 SX 6 3.2 33 70 115 173 289 492 796 1418 2532 85
PVP 7 SXLP 3 4.5 34 74 121 200 315 487 760 1348 2410 88
PVP 14 SX 6 4.8 23 49 80 120 200 340 550 980 1750 85
PVP 14 SXLP 3 6.9 24 52 85 140 220 340 530 940 1680 88
PVP 18 SX 6 6.4 18 38 62 93 155 264 420 750 1340 85
PVP 18 SXLP 3 8.6 18 39 64 105 165 255 398 706 1260 88
MSVE 3 4 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
MSVE 5 4 2.2 70 160 260 410 620 910 1500 2620 4490 85
MSVE 8 3.5 4.3 35 75 120 190 290 490 920 1530 2730 90
MSVE 12 3.5 5.5 27 57 100 150 230 350 740 1200 2150 90
MSVE 20 4 8.0 18 37 62 92 140 210 410 770 1220 90
AVG 18 6 6.4 22 44 75 115 185 258 430 798 1107 85 8
AVG 25 6 9.6 15 30 52 80 128 178 297 538 764 85
M3 5 0.8 106 244 491 969 1642 2398 4004 7128 10122 85
M7 5 1.4 61 142 285 563 954 1394 2328 4144 5885 85
M 10 5 1.9 40 93 188 371 629 918 1534 2731 3878 85
M 14 5 2.5 30 69 140 276 469 685 1144 2036 2892 85
M 18 5 3.6 21 48 98 193 327 478 799 1423 2020 85
M 3 SSX 5 0.8 106 244 491 969 1642 2398 4004 7128 10122 85
M 7 SSX 5 1.4 61 142 285 563 954 1394 2328 4144 5885 85
M 10 SSX 5 1.9 40 93 188 371 629 918 1534 2731 3878 85
M 14 SSX 5 2.5 30 69 140 276 469 685 1144 2036 2892 85
M 18 SSX 5 3.6 21 48 98 193 327 478 799 1423 2020 85

To calculate the emptying time of a volume V, use the following formula: t 1= t x V

t1 = time to be calculated (ms)
t = time indicated in the table (ms) in the desired degree of vacuum column (-KPa)
V = Volume to be emptied (L)
8.03
TABLE REGARDING VACUUM GENERATOR EVACUATION TIME,
AT DIFFERENT LEVELS OF VACUUMS
3D drawings are available on vuototecnica.net

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa)

Generator
Item Supp. press. Air consumption at optimal supply pressure Max vacuum
bar Nl/s 10 20 30 40 50 60 70 80 85 -KPa
MVG 3 5 0.8 119 274 552 1088 1845 2694 4499 8009 11373 85
MVG 7 5 1.3 58 133 268 529 897 1310 2188 3895 5531 85
MVG 10 5 1.7 41 95 192 379 642 938 1567 2790 3962 85
MVG 14 5 2.1 31 71 144 284 482 704 1175 2092 2971 85
GVMM 3 5 0.8 128 294 592 1167 1978 2889 4824 8588 12195 85
GVMM 7 5 1.3 59 137 275 543 921 1344 2245 3997 5676 85
GVMM 10 5 1.7 42 97 195 384 651 951 1589 2828 4016 85
GVMM 14 5 2.1 31 72 146 288 489 714 1193 2124 3016 85
MI 3 5 0.8 128 294 592 1167 1978 2889 4824 8588 12195 85
MI 7 5 1.3 59 137 275 543 921 1344 2245 3997 5676 85
MI 10 5 1.7 42 97 195 384 651 951 1589 2828 4016 85
MI 14 5 2.1 31 72 146 288 489 714 1193 2124 3016 85
PVP 12 MX 6 1.5 15 38 85 204 365 559 929 1607 5916 90
PVP 12 MXLP 3 2.3 22 56 120 240 410 650 975 1950 7160 86
PVP 25 MX 6 3.0 10 26 57 137 246 377 626 1083 3986 90
PVP 25 MXLP 3 4.5 16 41 83 165 290 460 690 1380 5070 86
PVP 40 M 6 3.2 7 19 42 101 182 278 462 799 2943 90
PVP 40 MLP 3 4.4 12 28 58 116 158 250 382 764 2820 88
PVP 70 M 6 6.6 4 10 22 53 95 146 242 419 1544 90
PVP 70 MLP 3 8.9 9 21 44 88 120 190 290 580 2150 88
PVP 100 M 6 9.8 3 7 16 39 70 108 179 310 1144 90
PVP 100 MLP 3 13.3 7 16 34 68 93 147 224 448 1650 88
PVP 140 M 6 13.0 2.1 5.3 11.7 28.0 50.2 76.9 127 220 812 90
PVP 140 MLP 3 17.8 3.6 8.4 17.7 35.4 48.3 76.5 116 233 860 88
PVP 170 M 6 16.3 1.7 4.4 9.7 23.4 42.0 64.2 106 184 678 90
PVP 170 MLP 3 22.2 3.0 7.1 14.9 29.9 40.6 64.2 98.0 196 720 88
PVP 200 M 6 19.4 1.6 4.0 8.9 21.3 38.2 58.4 97.0 167 618 90
PVP 200 MLP 3 26.6 2.8 6.5 13.6 27.3 37.2 58.8 89.7 180 665 88
PVP 250 M 6 24.0 1.1 2.9 6.4 15.2 27.3 41.8 69.3 119 442 90
PVP 250 MLP 3 33.6 2.0 4.6 9.6 19.3 26.3 41.5 63.5 127 468 88
PVP 300 M 6 29.0 1.0 2.5 5.5 13.3 23.8 36.5 60.6 104 386 90
PVP 300 MLP 3 39.3 1.7 3.9 8.2 16.4 22.3 35.3 54.0 108 398 88
PVP 25 MDX 6 3.2 7.5 18.8 41.3 99.3 177 271 451 781 2874 90
PVP 25 MDXLP 3 4.4 13.0 33.3 67.2 134 238 376 564 1128 4151 88
PVP 35 MDX 6 4.8 6.5 14.1 31.2 74.9 134 205 340 589 2618 90
PVP 35 MDXLP 3 6.5 9.8 25.2 50.9 101 180 284 427 854 3145 88
PVP 50 MDX 6 6.5 4.7 11.9 26.2 62.8 112 172 285 494 1818 90
PVP 50 MDXLP 3 8.6 7.9 20.3 41.0 82.0 145 229 344 688 2534 88
PVP 60 MDX 6 8.2 3.5 8.8 19.3 46.4 83.0 127 211 365 1343 90
PVP 60 MDXLP 3 11.0 6.6 16.8 34.0 68.0 120 190 285 570 2098 88
8 PVP 75 MDX 6 9.8 3.1 7.8 17.2 41.4 74.2 113 188 326 1200 90
PVP 75 MDXLP 3 13.2 5.7 14.5 29.2 58.4 103 163 245 490 1805 88
PVP 150 MD 6 16.0 1.6 4.0 8.9 21.3 38.2 58.4 97.0 167 618 90
PVP 150 MDLP 3 22.6 2.9 7.5 15.0 30.1 53.3 84.2 126 252 930 88
PVP 300 MD 6 32.0 0.8 2.0 4.4 10.6 19.1 29.2 48.5 83.9 386 90
PVP 300 MDLP 3 45.5 2.0 5.2 10.5 21.0 37.2 58.7 88.0 176 650 88
PVP 450 MD 6 47.8 0.5 1.4 3.0 7.4 13.2 20.1 33.5 57.9 213 90
PVP 450 MDLP 3 65.8 1.2 3.0 6.2 12.4 22.0 34.7 52.0 104 383 88
PVP 600 MD 6 63.2 0.4 1.0 2.4 5.7 10.2 15.6 25.9 44.8 165 90
PVP 600 MDLP 3 87.7 0.8 2.0 4.1 8.2 14.6 23.1 34.7 69.4 256 88
PVP 750 MD 6 80.0 0.3 0.8 1.8 4.3 7.7 11.8 19.5 33.8 125 90
PVP 750 MDLP 3 110.0 0.5 1.3 2.6 5.2 9.2 14.5 21.7 43.4 160 88

To calculate the emptying time of a volume V, use the following formula: t 1= t x V

t1 = time to be calculated (ms)
t = time indicated in the table (ms) in the desired degree of vacuum column (-KPa)
V = Volume to be emptied (L)
8.04
SINGLE-STAGE VACUUM GENERATORS 15 01 10, 15 01 10 LP, 15 01 15 LP and 15 03 10

Single-stage vacuum generator operation is based on the Venturi

principle.
Supplying the generator with compressed air in P, vacuum will be
generated at connection U, while both the supply and the sucked air

3D drawings are available on vuototecnica.net

will be released through R.
By interrupting the air supply in P, the vacuum effect in U will also stop.
The optimal air supply pressure is normally 6 bar, but for generators
with the letters LP in their item, a pressure lower than 4 bar is sufficient
to obtain the best performance. Upon request, the vacuum generators
can be supplied with a high sound suppression silencer installed on the
R exhaust connection.
The single-stage vacuum generators are generally used to control
vacuum cups, for gripping and handling non-porous objects and
equipment with low flow rate requirements.
They are fully made with anodised aluminium, with brass or aluminium
ejectors, depending on the items.

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION 8

Item 15 01 10 15 01 10 LP 15 01 15 LP
Intake air flow rate m3/h 2.7 2.8 2.9 2.6 2.8 3.0 4.8 4.9 5.0
Maximum level of vacuum -KPa 55 70 85 43 61 85 40 61 85
Final pressure mbar abs. 450 300 150 570 390 150 600 390 150
Supply pressure bar 4 5 6 2 3 4 2 3 4
Optimal supply pressure bar 6 4 4
Air consumption Nl/s 0.7 0.8 0.9 0.7 0.9 1.2 1.3 1.7 2.2
Operating temperature °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 63 62 71
Weight g 140 130 130
A mm 3 5
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.05
SINGLE-STAGE VACUUM GENERATORS 15 01 10, 15 01 10 LP and 15 01 15 LP

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
150110 portata FVG5 portata
FVG3 portata

15 01 10 15 01 10 LP 15 01 15 LP
3D drawings are available on vuototecnica.net

0,9 0,9 1,6

0,8 0,8 1,4

0,7 0,7
1,2

0,6 0,6
1
0,5 0,5
Nl/s

Nl/s
0,8

Nl/s
0,4 0,4
FVG3 portata FVG5 portata
0,6
0,3 0,3

150110 portata 0,4

0,2 0,2
0,9 1,6
0,1 0,2
0,1
0,8 1,4
0,9
0 0 0
0 10 20 30 40 50 60 70 80 0,7 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0,8 1,2
-Kpa -Kpa -Kpa
0,6
0,7 temp
150110 1
0,5
0,6

Nl/s
0,8
Nl/s

FVG3 0,4 temp Air flow rate (Nl/s) at differentFVG5

leveltemp
of vacuum (-KPa) Max vacuum
6000
0,5 Generator Supp. press. Air consumption
at optimal supply pressure 0,6
Nl/s

0,4 item bar Nl/s 0,3

5000 10000
0,2
0 10 20 30 40 50 5000
0,4 60 70 80 -KPa
0,3
15 01 10 6.0 0.9 9000
0,1 0.80 0.66 0.61 0.55 0.44 0.29 4500
0,20.19 0.09 -- 85
4000
0,2
15 01 10 LP 4.0 1.2 8000
0
0.83 0.67 0.63 0.56 0.49 0.414000
0
0.34 0.18 0.08 85
0,1 15 01 15 LP 4.0 2.2 7000 01.3910 1.2230
20 1.11
40 50 1.00
60 70 0.90
80 0.693500 0.44
0 10 0.30
20 30 0.16
40 50 60 8570 80
3000
ms/l

-Kpa -Kpa
0 6000 3000
0 10 20 30 40 50 60 70 80

ms/l
2500
ms/l

2000 -Kpa 5000

150110 temp
Evacuation rates (ms/l =s/m 3
) at different levels of vacuums (-KPa) at2000
4000
optimal supply pressure
FVG3 temp FVG5 temp
1000 3000 1500

6000
15 01 10 2000
10000
15 01 10 LP 1000
5000
15 01 15 LP
0
10 20 30 40 50 60 70 80 1000
9000 500
4500
-Kpa
5000 0
0
8000 4000
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
7000 -Kpa 3500 -Kpa
4000
6000 3000
ms/l

2500
ms/l

3000 5000
ms/l

4000 2000
2000
3000 1500

2000 1000
1000
1000 500

0 0 0
10 20 30 40 50 60 70 80 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
15 01 10 6.0 0.9 139 278 472 727 1171 1628 2720 4928 -- 85
15 01 10 LP 4.0 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
15 01 15 LP 4.0 2.2 70 160 260 410 620 910 1500 2620 4490 85

8
ACCESSORIES UPON REQUEST
Silencer item SSX 1/4’’

8.06
SINGLE-STAGE VACUUM GENERATOR 15 03 10

3D drawings are available on vuototecnica.net

8
P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION
Item 15 03 10
Intake air flow rate m /h3
4.8 5 5
Maximum level of vacuum -KPa 62 78 85
Final pressure mbar abs. 380 220 150
Supply pressure bar 4 5 6
Optimal supply pressure bar 6
Air consumption Nl/s 1.1 1.3 1.6
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 79
Weight g 179
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.07
SINGLE-STAGE VACUUM GENERATOR 15 03 10

Air flow rate (Nl/s)150310 portata

at different level of vacuum (-KPa) at optimal supply pressure

1,6
3D drawings are available on vuototecnica.net

1,4

1,2

150310 portata

Nl/s
0,8

0,6

1,6
0,4

1,4
0,2

1,2
0
0 10 20 30 40 50 60 70 80
1
-Kpa
Nl/s

0,8
150310 temp
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
0,6
at optimal supply pressure
item bar Nl/s 4500
0,4 0 10 20 30 40 50 60 70 80 -KPa
4000
15 03 10 6.0 1.6 0,2 1.39 1.30 1.15 1.00 0.89 0.77 0.69 0.44 0.04 85
3500
0
3000 0 10 20 30 40 50 60 70 80
-Kpa
Evacuation rates (ms/l 2500
=s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
ms/l

150310 temp
2000

1500
4500
1000
4000
500
3500
0
3000 10 20 30 40 50 60 70 80 85
-Kpa
2500
ms/l

2000

1500

1000

500

0
10 20 30 40 50 60 70 80 85
-Kpa

ACCESSORIES UPON REQUEST

8
Silencer item SSX 1/2’’

8.08
SINGLE-STAGE VACUUM GENERATORS 15 05 08 SX, 15 05 10 SX and 15 07 10 SX

The operation of these single-stage vacuum generators is also based on the Venturi
principle. It differs from the generators described above for its increased suction flow
rate, lower supply air pressure, lower than 4 bar to obtain the best performance, and for
the SSX silencer ... with high acoustic dampening, installed as standard on the R exhaust

3D drawings are available on vuototecnica.net

connection.
They are also used in the automotive sector to control vacuum cups, for the handling and
gripping of only slightly porous objects, sheet, wood panel, marble slab and glass and
other similar objects.
They are fully made with anodised aluminium.

Vacuum
connection

Silencer

Compressed air
connection

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item 15 05 08 SX 15 05 10 SX
8
Intake air flow rate m3/h 8.0 8.6 8.8 12.0 12.2 12.5
Maximum level of vacuum -KPa 40 60 90 40 60 90
Final pressure mbar abs. 600 400 100 600 400 100
Supply pressure bar 2 3 3.5 2 3 3.5
Optimal supply pressure bar 3.5 3.5
Air consumption NI/s 2.8 3.8 4.3 3.7 5 5.5
Operating temperature °C -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 60 63
Weight g 310 306

Spare parts 15 05 08 SX 15 05 10 SX
Silencer item SSX 3/8” SSX 3/8”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.09
SINGLE-STAGE VACUUM GENERATORS 15 05 08 SX and 15 05 10 SX

150518SX portata
3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa)

150510 portataat optimal supply pressure

15 05 08 SX 15 05 10 SX
3 4

3,5
2,5

2
2,5
150518SX portata
Nl/s

Nl/s
1,5 2 portata
150510

1,5
1

3 41
0,5
0,5
3,5
2,5
0 30
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
2 -Kpa -Kpa
2,5
Nl/s

Nl/s

150518SX temp 1,5 2

Air flow rate (Nl/s)temp

150510 at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption 1,5
1 at optimal supply pressure
item bar Nl/s
0 10 20 1 30 40 50 60 70 80 -KPa
153000
05
0,508 SX 3.5 4.3 2.44 2.27 2.112500 1.94 1.72 1.46 0.98 0.50 0.04 90
15 05 10 SX 3.5 5.5 3.47 3.24 2.86 0,5 2.49 2.22 1.92 1.72 1.20 0.65 90
2500
0 0
2000
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
2000
1500
150518SX temp
ms/l

ms/l

1500 Evacuation rates (ms/l =s/m ) at different levels of vacuums

temp (-KPa) at optimal supply pressure
3
150510

1000
1000
15 05 08 SX 15 05 10 SX
3000 2500
500
500

2500
2000
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
2000
-Kpa -Kpa
1500
ms/l

ms/l

1500

1000
1000

8 500
500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.10
SINGLE-STAGE VACUUM GENERATOR 15 07 10 SX

3D drawings are available on vuototecnica.net

Vacuum
connection

Silencer

Compressed air
connection

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item 15 07 10 SX
8
Intake air flow rate m3/h 18 19 20
Maximum level of vacuum -KPa 40 60 90
Final pressure mbar abs. 600 400 100
Supply pressure bar 2 3 3.5
Optimal supply pressure bar 3.5
Air consumption NI/s 6.0 7.7 8.5
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 66
Weight g 355

Spare parts 15 07 10 SX
Silencer item SSX 1/2”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.11
SINGLE-STAGE VACUUM GENERATOR 15 07 10 SX

150710SX portata
3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure

4
Nl/s

150710SX portata

1
6

0
5 0 10 20 30 40 50 60 70 80
-Kpa

4
150710SX temp
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
Nl/s

3
1400
item bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
15 07 10 SX 3.5 8.5
2
1200 5.55 5.00 4.44 4.16 3.83 3.00 1.97 1.56 0.85 90

1000
1

800
0
ms/l

0 10 20 30 40 50 60 70 80
600 -Kpa
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
400
150710SX temp

200
1400

0
1200 10 20 30 40 50 60 70 80 85
- Kpa
1000

800
ms/l

600

400

8
200

0
10 20 30 40 50 60 70 80 85
- Kpa

8.12
SINGLE-STAGE VACUUM GENERATORS VG 03, VG 03 LP and VG 05 LP

This series of single-stage vacuum generators, also based on the

Venturi principle, can be supplied for optimal supply pressures of 4
or 6 bars. Thanks to their shape, they can be installed directly on the
user device and used at the most suitable supply pressure, depending

3D drawings are available on vuototecnica.net

on the desired level of vacuum. They have different capacities and
can be used in all gripping systems with vacuum cups, for gripping
and handling objects that are not very porous and on equipment with
limited capacities. They are available upon request with an SSX 3/8 "R
high sound suppression silencer, installed on air exhaust R. They are
fully made with anodised aluminium, with brass or aluminium ejectors,
depending on the items.

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION 8

Item VG 03 VG 03 LP VG 05 LP
Intake air flow rate m3/h 2.7 2.8 2.9 2.6 2.8 3.0 4.8 4.9 5.0
Maximum level of vacuum -KPa 55 70 85 43 61 85 40 61 85
Final pressure mbar abs. 450 300 150 570 390 150 600 390 150
Supply pressure bar 4 5 6 2 3 4 2 3 4
Optimal supply pressure bar 6 4 4
Air consumption Nl/s 0.7 0.8 0.9 0.7 0.9 1.2 1.3 1.7 2.2
Operating temperature °C -10 / +80 -10 / +80 -10 / +80
Noise level at
optimal supply pressure dB(A) 63 62 71
Weight g 134 124 124
A mm 6 9 11
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.13
SINGLE-STAGE VACUUM GENERATORS VG 03, VG 03 LP and VG 05 LP

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
150110 portata FVG5 portata
FVG3 portata

VG 03 VG 03 LP VG 05 LP
3D drawings are available on vuototecnica.net

0,9 0,9 1,6

0,8 0,8 1,4

0,7 0,7
1,2

0,6 0,6
1
0,5 0,5
Nl/s

Nl/s
0,8

Nl/s
0,4 0,4
FVG3 portata FVG5 portata
0,6
0,3 0,3
150110 portata
0,4
0,2 0,2
0,9 1,6

0,1 0,2
0,1 0,8 1,4
0,9
0 0
0,7 0
0,8 0 10 20 30 40 50 60 70 80 1,2 0 10 20 30 40 50 60 70 80
0 10 20 30 40 50 60 70 80
-Kpa 0,6 -Kpa -Kpa
0,7 1
150110 temp
0,5
0,6

Nl/s
0,8
Nl/s

0,4 Air flow rate (Nl/s) at differentFVG5levels of vacuums (-KPa) Max vacuum
0,5 Generator Supp. press. Air consumption temp
FVG3 temp
6000 at optimal supply pressure 0,6
Nl/s

0,4 item bar Nl/s 0,3

0,2
10000
0 10 20 30 40 500,4 60 70 80 -KPa
5000 5000
0,3
VG 03 6.0 0.9 9000
0,1 0.80 0.66 0.61 0.55 0.44 0.29
0,2
4500 0.19 0.09 -- 85
0,2
4000 VG 03 LP 4.0 1.2 8000
0
0.83 0.67 0.63 0.56 0.49 0.41
4000
0
0.34 0.18 0.08 85
0,1 VG 05 LP 4.0 2.2 7000
0 1.39
10 201.2230 1.1150
40 1.00 70
60 0.90
80 0.69
3500
00.4410 0.3030
20 0.1650
40 60 85
70 80
-Kpa -Kpa
3000
ms/l

0
6000 3000
0 10 20 30 40 50 60 70 80
-Kpa
Evacuation rates (ms/l =s/m5000
) at different levels of vacuums (-KPa) at optimal

ms/l
3 2500 supply pressure
ms/l

2000
150110 temp FVG3 4000temp FVG5 temp
2000

VG 03 VG 03 LP VG 05 LP
1000 3000 1500

6000 10000 5000

1000
2000
0
10 20 30 40 50 60 70 80 9000 4500
500
1000
5000 -Kpa
8000 4000
0
0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
7000 3500
4000 -Kpa -Kpa
6000 3000
ms/l

2500
ms/l

3000 5000
ms/l

4000 2000
2000
3000 1500

2000 1000
1000
1000 500

0 0 0
10 20 30 40 50 60 70 80 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
VG 03 6.0 0.9 139 278 472 727 1171 1628 2720 4928 -- 85
VG 03 LP 4.0 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
VG 05 LP 4.0 2.2 70 160 260 410 620 910 1500 2620 4490 85

8
ACCESSORIES UPON REQUEST
Silencer item SSX 3/8’’ R

8.14
SINGLE-STAGE VACUUM GENERATORS
WITH EJECTOR 15 02 10, 15 02 10 LP, 15 02 15 LP and 15 04 10
This single-stage vacuum generator operation is based on the
Venturi principle. When the generator is supplied with compressed
air in P, the vacuum will be generated at connection U and the
supply air with the suctioned air will be discharged in R. During the

3D drawings are available on vuototecnica.net

operating cycle, a chamber inside the generator body will be supplied
and, when supply stops in P, the compressed air accumulated in it
will be discharged through the U connection, quickly the restoring
atmospheric pressure of use.
If when using U, for example, it is connected to a vacuum cup, it will
disconnect much faster with this ejector system with respect to the
previously described vacuum generators. The optimal air supply
pressure is normally 6 bar, but for generators with the letters LP in
their item, a pressure lower than 4 bar is sufficient to obtain the best
performance. They are fully made with anodised aluminium, with
brass or aluminium ejectors, depending on the items.

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item 15 02 10 15 02 10 LP 15 02 15 LP
Intake air flow rate m /h
3
2.7 2.8 2.9 2.6 2.8 3.0 4.8 4.9 5.0
8
Maximum level of vacuum -KPa 55 70 85 43 61 85 40 61 85
Final pressure mbar abs. 450 300 150 570 390 150 600 390 150
Supply pressure bar 4 5 6 2 3 4 2 3 4
Optimal supply pressure bar 6 4 4
Air consumption Nl/s 0.7 0.8 0.9 0.7 0.9 1.2 1.3 1.7 2.2
Operating temperature °C -20 / +80 -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 63 63 65
Weight g 319 320 320
A mm 3 5

Spare parts 15 02 10 15 02 10 LP 15 02 15 LP
Sealing kit item 00 15 500 00 15 500 00 15 500
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.15
SINGLE-STAGE VACUUM GENERATORS
WITH EJECTOR 15 02 10, 15 02 10 LP and 15 02 15 LP

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
150210 portata
FVG3 portata FVG5 portata

15 02 10 15 02 10 LP 15 02 15 LP
3D drawings are available on vuototecnica.net

0,9 0,9 1,6

0,8 0,8 1,4

0,7 0,7
1,2

0,6 0,6
1

0,5 0,5

Nl/s
0,8
Nl/s

Nl/s
0,4 0,4
FVG3 portata FVG5 portata
150210 portata 0,6
0,3 0,3

0,4
0,2 0,2
0,9 1,6

0,9 0,1 0,2

0,1 0,8 1,4

0,8
0 0
0,7 0
0 10 20 30 40 50 60 70 80 1,2 0 10 20 30 40 50 60 70 80
0 10 20 30 40 50 60 70 80
0,7 -Kpa 0,6 -Kpa -Kpa
1
0,6 0,5
150210 temp

Nl/s
0,8
Nl/s

0,5
0,4 Air flow rate (Nl/s) at different FVG5
levelstemp
of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
FVG3 temp
Nl/s

0,4 at optimal supply pressure 0,6

6000 item bar Nl/s 0,3

0,3 10000
0,2
0 10 20 30 40 50 5000
0,4 60 70 80 -KPa
5000
0,2 15 02 10 6.0 0.9 9000
0,1 0.80 0.66 0.61 0.55 0.44 0.294500
0,2 0.19 0.09 -- 85
0,1 15 02 10 LP 4.0 1.2 8000
0
0.83 0.67 0.63 0.56 0.49 0.414000
0
0.34 0.18 0.08 85
4000
0
15 02 15 LP 4.0 2.2 7000
01.3910 1.2230
20 1.11
40 50 1.00
60 70 0.90
80 0.693500 0.44
0 10 0.30
20 30 0.16
40 50 60 8570 80
-Kpa -Kpa
0 10 20 30 40 50 60 70 80
6000 3000
ms/l

3000 -Kpa

ms/l
Evacuation rates (ms/l =s/m5000
3
) at different levels of vacuums (-KPa) at optimal
2500 supply pressure
ms/l

150210 temp
2000 FVG3 4000temp FVG5 temp
2000

1000 15 02 10 3000

10000
15 02 10 LP 1500

5000
15 02 15 LP
6000 2000 1000

9000
1000 4500
500
0
5000 10 20 30 40 50 60 70 80 8000
0 4000
0
-Kpa 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
7000 3500
4000 -Kpa -Kpa
6000 3000
ms/l
ms/l

2500
ms/l

3000 5000

4000 2000
2000
3000 1500

2000 1000
1000
1000 500

0 0 0
10 20 30 40 50 60 70 80 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
15 02 10 6.0 0.9 139 278 472 727 1171 1628 2720 4928 -- 85
15 02 10 LP 4.0 1.2 130 260 510 740 1070 1510 2430 4400 8740 85
15 02 15 LP 4.0 2.2 70 160 260 410 620 910 1500 2620 4490 85

8 ACCESSORIES UPON REQUEST

Silencer item SSX 1/4’’

8.16
SINGLE-STAGE VACUUM GENERATOR WITH EJECTOR 15 04 10

3D drawings are available on vuototecnica.net

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item 15 04 10
8
Intake air flow rate m3/h 4.8 5 5
Maximum level of vacuum -KPa 62 78 85
Final pressure mbar abs. 380 220 150
Supply pressure bar 4 5 6
Optimal supply pressure bar 6
Air consumption Nl/s 1.1 1.3 1.6
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 79
Weight g 501

Spare parts 15 04 10
Sealing kit item 00 15 501
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.17
SINGLE-STAGE VACUUM GENERATOR WITH EJECTOR 15 04 10

150410 portata
Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
3D drawings are available on vuototecnica.net

1,6

1,4

150410 portata
1,2

1,6

Nl/s
0,8

1,4
0,6

1,2
0,4

1
0,2
Nl/s

0,8
0
0 10 20 30 40 50 60 70 80
0,6 -Kpa

0,4

150410 temp Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
0,2 at optimal supply pressure
item bar Nl/s
0 0 10 20 30 40 50 60 70 80 -KPa
0 10 20 30 40 50 60 70 80
15 04 10 6.0 1.64500 1.39 1.30 -Kpa 1.15 1.00 0.89 0.77 0.69 0.44 0.04 85

4000
150410 temp

Evacuation rates (ms/l3500

=s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
3000

2500
4500
ms/l

2000
4000

1500
3500

1000
3000

500
2500
ms/l

0
2000 10 20 30 40 50 60 70 80 85
-Kpa
1500

1000

500

0
10 20 30 40 50 60 70 80 85
-Kpa

ACCESSORIES UPON REQUEST

8 Silencer item SSX 1/2’’

8.18
SINGLE-STAGE VACUUM GENERATOR WITH EJECTOR 15 06 08 SX and 15 06 10 SX

These have the same technical features as 15 05 08 SX and 15 05 10 SX,

with the addition of the pneumatic ejector. For the ejection system, air
accumulated in a special chamber inside the generator body during
the operating cycle is automatically discharged in connection to use U,

3D drawings are available on vuototecnica.net

once supply in P is completed and suitably dosed by means of a screw-
type flow regulator, for quick restoration of the atmospheric pressure.
Optimal supply pressure is less than 4 bar. A high acoustic dampening
silencer, set on exhaust air discharge R, reduces noise to a minimum
and is an integral part of the generator. These generators, like the
previous ones, are also fully made with anodised aluminium.

Vacuum
connection

Silencer SSX 3/8’’

Screw-type flow
regulator Blow off

Compressed air
connection

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item 15 06 08 SX 15 06 10 SX
Intake air flow rate m /h3
8.0 8.6 8.8 12.0 12.2 12.5
8
Maximum level of vacuum -KPa 40 60 90 40 60 90
Final pressure mbar abs. 600 400 100 600 400 100
Supply pressure bar 2 3 3.5 2 3 3.5
Optimal supply pressure bar 3.5 3.5
Air consumption Nl/s 2.8 3.8 4.3 3.7 5.0 5.5
Operating temperature °C -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 60 63
Weight g 310 306

Spare parts 15 06 08 SX 15 06 10 SX
Sealing kit item 00 15 414 00 15 414
Silencer item SSX 3/8” SSX 3/8”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.19
SINGLE-STAGE VACUUM GENERATOR WITH EJECTOR 15 06 08 SX and 15 06 10 SX

MSVE 8 portata
Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
3D drawings are available on vuototecnica.net

150610 portata

3
15 06 08 SX 15 06 10 SX
4

2,5 3,5

3
2
2,5
Nl/s

MSVE 8 portata
1,5

Nl/s
2
150610 portata
1,5
1

1
3 4
0,5
0,5
3,5
2,5
0 0
0 10 20 30 40 50 60 70 80 3 0 10 20 30 40 50 60 70 80 88
-Kpa -Kpa
2
2,5
Nl/s

Nl/s

1,5 150610
2 temp
MSVE 8 temp Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
1,5
item1 bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
3000 2500
1
15 06 08 SX 3.5 4.3 2.44 2.27 2.11 1.94 1.72 1.46 0.98 0.50 0.04 90
0,5
15 06 10 SX 3.5 5.5 3.47 3.24 2.86 0,5 2.49 2.22 1.92 1.72 1.20 0.65 90
2500
2000
0 0
2000 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 88
-Kpa -Kpa
1500
ms/l

1500
ms/l

Evacuation rates (ms/l =s/m3) at different levels150610

of vacuums
temp (-KPa) at optimal supply pressure
MSVE 8 temp 1000
1000

15 06 08 SX 15 06 10 SX
3000 500
2500
500

2500
0 0
2000
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 88
-Kpa -Kpa
2000
1500
ms/l

ms/l

1500

1000
1000

8 500
500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 88
-Kpa -Kpa

8.20
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR FVG 3 and FVG 5

Specifically designed for very high frequency gripping and release

applications, these single-stage vacuum generators are based on the
Venturi principle and are equipped with a pneumatic ejector to allow
maximum speed in restoring the atmospheric pressure of use.

3D drawings are available on vuototecnica.net

The key features are its considerably reduced weight, supply air
pressure of less than 4 bar, low energy consumption, simplicity
of installation and low noise level during use, thanks to the
high sound dampening silencer installed as standard on the
generators. The pneumatic ejector can be deactivated simply
by means of a membrane integrated onto the generators. These
generators, like the previous ones, are also fully made with
anodised aluminium.

2 M4
fixing holes

2 M5
fixing holes

2 additional vacuum connections

Silencer

2 additional compressed air connections

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item FVG 3 FVG 5
Intake air flow rate m /h3
2.6 2.8 3.0 4.8 4.9 5.0
8
Maximum level of vacuum -KPa 43 61 85 40 61 85
Final pressure mbar abs. 570 390 150 600 390 150
Supply pressure bar 2 3 4 2 3 4
Optimal supply pressure bar 4 4
Air consumption Nl/s 0.7 0.9 1.2 1.3 1.7 2.2
Operating temperature °C -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 68 74
Weight g 84 86

Spare parts FVG 3 FVG 5

Silencer item SSX 1/4” SSX 1/4”
Sealing kit and reed valves item 00 15 502 00 15 502
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.21
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR FVG 3 and FVG 5

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
3D drawings are available on vuototecnica.net

FVG3 portata FVG5 portata

0,9
FVG 3 1,6
FVG 5
0,8 1,4

0,7
1,2

0,6
1
0,5

Nl/s
0,8
Nl/s

FVG3 0,4 portata FVG5 portata

0,6
0,3

0,9 0,4
1,6
0,2

0,8
0,1 0,2
1,4

0,7
0 0
1,2
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0,6 -Kpa -Kpa
1
0,5
Nl/s

0,8
Nl/s

0,4
FVG3 temp AirFVG5
flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption temp
0,6
0,3 at optimal supply pressure
item bar Nl/s
0 10 20 0,4 30 40 50 60 70 80 -KPa
0,2
10000 5000
FVG 3 4.0 1.2 0.83 0.67 0.63 0.56 0.49 0.41 0.34 0.18 0.08 85
0,2
FVG
0,15
9000 4.0 2.2 1.39 1.22 1.114500 1.00 0.90 0.69 0.44 0.30 0.16 85
0
8000 0
4000
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
7000 -Kpa 3500 -Kpa

6000 3000
ms/l

Evacuation rates (ms/l =s/m3) at different levels of2500

ms/l

5000
vacuums (-KPa) at optimal supply pressure
FVG3 temp FVG5 temp
4000 2000

3000
10000
FVG 3 1500
5000
FVG 5
2000 1000
9000 4500
1000 500
8000 4000
0 0
7000 10 20 30 40 50 60 70 80 85 3500 10 20 30 40 50 60 70 80 85
-Kpa -Kpa
6000 3000
ms/l

2500
ms/l

5000

4000 2000

3000 1500

8 2000 1000

1000 500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.22
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR FVG 8 and FVG 12

Specifically designed for very high frequency gripping and release

applications, these single-stage vacuum generators are based on the
Venturi principle and are equipped with a pneumatic ejector, which
can be implemented on request through the M7 connection on the

3D drawings are available on vuototecnica.net

lid, to allow maximum speed in restoring the atmospheric
pressure of use. The key features are its considerably reduced
weight, supply compressed air pressure of less than 4 bar, low
energy consumption, simplicity of installation and low noise
level during use, thanks to the high sound dampening silencer
installed as standard on the generators. The pneumatic ejector
can be deactivated simply by means of a membrane integrated
onto the generators. These generators, like the previous ones, are
also fully made with anodised aluminium.

2 M4 fixing holes

2 M5
fixing holes

2 additional G1/4” vacuum connections

Additional M7 connection blow off Silencer

2 additional G1/4” compressed air connections

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item FVG 8 FVG 12
Intake air flow rate m /h3
8.0 8.6 8.8 12.0 12.2 12.5
8
Maximum level of vacuum -KPa 40 60 90 40 60 90
Final pressure mbar abs. 600 400 100 600 400 100
Supply pressure bar 2 3 3.5 2 3 3.5
Optimal supply pressure bar 3.5 3.5
Air consumption Nl/s 2.8 3.8 4.3 3.7 5 5.5
Operating temperature °C -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 60 63
Weight g 250 252

Spare parts FVG 8 FVG 12

Silencer item SSX 3/8” SSX 3/8”
Sealing kit and reed valves item 00 15 538 00 15 538
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.21-1
8.21
SINGLE-STAGE VACUUM GENERATORS WITH EJECTOR FVG 8 and FVG 12

150518SX portata
Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
3D drawings are available on vuototecnica.net

150510 portata

FVG 8 FVG 12
3 4

3,5
2,5

2
2,5
150518SX portata
Nl/s

Nl/s
1,5 2 portata
150510

1,5
1

3 41
0,5
0,5
3,5
2,5
0 30
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
2 -Kpa -Kpa
2,5
Nl/s

Nl/s

150518SX temp 1,5 2

Air flow rate (Nl/s)temp

150510 at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption 1,5
1 at optimal supply pressure
item bar Nl/s
0 10 20 1 30 40 50 60 70 80 -KPa
FVG
3000
0,5 8 3.5 4.3 2.44 2.27 2.112500 1.94 1.72 1.46 0.98 0.50 0.04 90
FVG 12 3.5 5.5 3.47 3.24 2.86 0,5 2.49 2.22 1.92 1.72 1.20 0.65 90
2500
0 0
2000
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
2000
1500
150518SX temp
ms/l

ms/l

1500 Evacuation rates (ms/l =s/m ) at different levels150510

3
of vacuums
temp (-KPa) at optimal supply pressure

1000
1000
FVG 8 FVG 12
3000 2500
500
500

2500
2000
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
2000
-Kpa -Kpa
1500
ms/l

ms/l

1500

1000
1000

8 500
500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.22-1
8.22
IN-LINE SINGLE-STAGE VACUUM GENERATOR PVP 1

This new range of vacuum generators also makes use of the Venturi
principle.
Their distinctive feature compared with traditional vacuum generators
are the two air and vacuum supply connections located in-line on the

3D drawings are available on vuototecnica.net

same axis, while the exhaust connection of the sucked and exhaust air
is orthogonal to them and is located on the generator circumference.
These vacuum generators are easy to disassemble, thus allowing
visibility and access to all the components. The advantages of these
generators include reduced overall dimensions, easy maintenance
and easy assembly to the vacuum cup supports or to the vacuum cup
holders.
As a standard, they are equipped with pressed stainless steel suction
filter and a special microfibre silencer, which is wrapped around the
exhaust connection, making them particularly silent.
They are fully made with anodised aluminium.

Sp17

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 1
Intake air flow rate m /h3
0.9 1.0 1.0
8
Maximum level of vacuum -KPa 60 80 85
Final pressure mbar abs. 400 200 150
Supply pressure bar 3 4 5
Optimal supply pressure bar 5
Air consumption Nl/s 0.30 0.35 0.45
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 62
Weight g 44

Spare parts PVP 1

Silencer item 00 15 114
Suction filter item SP 1/4 I
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.23
IN-LINE SINGLE-STAGE VACUUM GENERATOR PVP 1
3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
PVP1 portata

0,3

0,25

0,2
Nl/s

PVP1 portata
0,15

0,1
0,3

0,05
0,25

0
0,2
0 10 20 30 40 50 60 70 80
-Kpa
Nl/s

0,15

Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air 0,1
consumption
PVP1 temp 25000 at optimal supply pressure
item bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
PVP 1 5.0 0,050.45 0.27 0.25 0.22 0.18 0.12 0.07 0.06 0.03 -- 85
20000

0
0 10 20 30 40 50 60 70 80
15000
-Kpa
Evacuation rates (ms/l =s/m ) at different levels of vacuums (-KPa) at optimal supply pressure
3
ms/l

10000

PVP1 temp 25000

5000

20000

0
10 20 30 40 50 60 70 80 85
15000 -Kpa
ms/l

10000

8 5000

0
10 20 30 40 50 60 70 80 85
-Kpa

8.24
IN-LINE SINGLE-STAGE VACUUM GENERATORS GV 1, GV 2 and GV 3

These vacuum generators also operate based on the Venturi principle.

The feature that distinguishes them from classic vacuum generators
are the two air supply and the vacuum connections, located on the
same axis, while the connection relative to the intake-air discharge and

3D drawings are available on vuototecnica.net

exhaust air connections are set orthogonally to them.
The advantages of this configuration are less bulky dimensions, easy
assembly, and ease of maintenance. These vacuum generators can be
assembled directly onto the vacuum cup supports or on cup holders.
They are fully made with anodised aluminium, except the exhaust
nozzle which is made with brass.

Hex. 17

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item GV1 GV2 GV3 8
Intake air flow rate m3/h 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
Maximum level of vacuum -KPa 60 75 85 60 75 85 60 75 85
Final pressure mbar abs. 400 250 150 400 250 150 400 250 150
Supply pressure bar 3 4 5 3 4 5 3 4 5
Optimal supply pressure bar 5 5 5
Air consumption Nl/s 0.30 0.35 0.45 0.30 0.35 0.45 0.30 0.35 0.45
Operating temperature °C -20 / +80 -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 70 70 70
Weight g 21 20 19
A 30 35 38
C Ø M5 G1/8” G1/4”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.25
IN-LINE SINGLE-STAGE VACUUM GENERATORS GV 1, GV 2 and GV 3
3D drawings are available on vuototecnica.net

GV (Nl/s)portata
Air flow rate at different level of vacuum (-KPa) at optimal supply pressure

0,3

0,25
GV portata

0,2

0,3
0,15
Nl/s

0,25
0,1

0,2
0,05

0,15
Nl/s

0
0 10 20 30 40 50 60 70 80
-Kpa
0,1

Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air0,05
consumption
GV temp at optimal supply pressure
item bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
0
GV1 - GV2 - GV3 5.0 0.45 0 10
0.27
20
0.23
30
0.20 50 0.1760
40
0.13
70
0.06
80
0.05 0.03 -- 85
25000 -Kpa

20000
GV (ms/ltemp
Evacuation rates =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure

15000
ms/l

25000

10000

20000

5000

15000
ms/l

0
10 20 30 40 50 60 70 80 85
10000
-Kpa

8 5000

0
10 20 30 40 50 60 70 80 85
-Kpa

8.26
SINGLE-STAGE VACUUM GENERATORS PVP 05, PVP 2 and PVP 3

With their extremely reduced size and high performance, these single-
stage vacuum generators operate making use of the Venturi principle.
Supplying the generator with compressed air in P, vacuum will be
generated at connection U, while both the supply and the sucked air will

3D drawings are available on vuototecnica.net

be released through R. By interrupting the air supply in P, the vacuum
effect in U will also stop.
The vacuum generators described on this page are generally used for
interconnecting vacuum cups, for gripping and handling non-porous
objects and equipment with low flow rate requirements.
They are made with anodised aluminium, with ejectors in aluminium
(PVP05) or in brass (PVP2 - PVP3).
Upon request, they can be supplied with a high sound suppression
silencer installed on the R exhaust connection.

8
P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION
Item PVP 05
Intake air flow rate m /h3
0.36 0.42 0.42 0.47 0.50 0.50
Maximum level of vacuum -KPa 22 33 42 48 61 82
Final pressure mbar abs. 780 670 580 520 390 180
Supply pressure bar 1 2 3 4 5 6
Optimal supply pressure bar 6
Air consumption Nl/s 0.13 0.20 0.27 0.34 0.40 0.50
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 70
Weight g 14
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.27
SINGLE-STAGE VACUUM GENERATOR PVP 05

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
PVP 05 portata
3D drawings are available on vuototecnica.net

0,14

0,12

0,1

0,08
PVP 05 portata

Nl/s
0,14
0,06

0,12
0,04

0,1
0,02

0,08
0
Nl/s

0 10 20 30 40 50 60 70

0,06 -Kpa

0,04 Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
PVP 05 temp
at optimal supply pressure
item bar Nl/s
30000
0,02
0 10 20 30 40 50 60 70 80 -KPa
PVP 05 6.0 0.5 0 0.13 0.11 0.10 0.08 0.06 0.03 0.02 0.01 -- 82
25000 0 10 20 30 40 50 60 70
-Kpa

Evacuation rates (ms/l20000

=s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
ms/l

PVP 05 temp
15000
30000

10000
25000

5000
20000

0
ms/l

15000 10 20 30 40 50 60 70 80
-Kpa

10000

5000

0
10 20 30 40 50 60 70 80
-Kpa

8
ACCESSORIES UPON REQUEST
Silencer filter item FB 1

8.28
SINGLE-STAGE VACUUM GENERATOR PVP 2

3D drawings are available on vuototecnica.net

8
P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION
Item PVP 2
Intake air flow rate m /h3
2.8 2.9 3.0
Maximum level of vacuum -KPa 60 70 85
Final pressure mbar abs. 400 300 150
Supply pressure bar 4 5 6
Optimal supply pressure bar 6
Air consumption Nl/s 0.7 0.8 0.9
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 78
Weight g 70
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.29
SINGLE-STAGE VACUUM GENERATOR PVP 2

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
PVP 2 portata
3D drawings are available on vuototecnica.net

0,9

PVP 2 portata
0,8

0,7
0,9

0,6
0,8

0,5
0,7

Nl/s
0,4
0,6

0,3
Nl/s 0,5

0,2
0,4

0,1
0,3

0
0,2
0 10 20 30 40 50 60 70 80
-Kpa
0,1

0
0 10 20 Air30flow40
rate (Nl/s)
50 at different
60 70 levels of vacuums (-KPa)
80 Max vacuum
Generator Supp. press. Air consumption
-Kpa at optimal supply pressure
item bar PVP 2Nl/s temp
0 10 20 30 40 50 60 70 80 -KPa
PVP 2 6.0 0.9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 -- 85
PVP 2 temp
7000

Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
6000

7000
5000

6000
4000
ms/l

5000
3000

4000
2000
ms/l

3000
1000

2000
0
10 20 30 40 50 60 70 80 85
1000 -Kpa

0
10 20 30 40 50 60 70 80 85
-Kpa

8
ACCESSORIES UPON REQUEST
Silencer item SSX 1/8’’

8.30
SINGLE-STAGE VACUUM GENERATOR PVP 3

3D drawings are available on vuototecnica.net

8
P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION
Item PVP 3
Intake air flow rate m /h3
3.4 3.5 3.7
Maximum level of vacuum -KPa 60 70 85
Final pressure mbar abs. 400 300 150
Supply pressure bar 4 5 6
Optimal supply pressure bar 6
Air consumption Nl/s 1.0 1.1 1.3
Operating temperature °C -20 / +80
Noise level at
optimal supply pressure dB(A) 80
Weight g 100
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.31
SINGLE-STAGE VACUUM GENERATOR PVP 3

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
PVP 3 portata
3D drawings are available on vuototecnica.net

1,2

PVP 3 portata
1
1,2

0,8
1

Nl/s
0,6
0,8

0,4
Nl/s
0,6

0,2
0,4

0
0 10 20 30 40 50 60 70 80
0,2
-Kpa

0
Air30flow 40
rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. AirPVP
consumption
3 0
temp 10 20 50 60 70 80
-Kpa at optimal supply pressure
item bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
PVP 3 6.0 PVP 31.3 temp 1.03 0.82 0.72 0.61 0.41 0.24 0.15 0.08 -- 85

6000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure

5000
6000

4000
5000
ms/l

3000
4000

2000
ms/l

3000

1000
2000

0
10 20 30 40 50 60 70 80 85
1000
-Kpa

0
10 20 30 40 50 60 70 80 85
-Kpa

8
ACCESSORIES UPON REQUEST
Silencer item SSX 1/8’’

8.32
SINGLE-STAGE VACUUM GENERATORS PVP 2 M, PVP 2 MM1,
PVP 2 MM2 and PVP 2 MM3
The vacuum generators on this page are based on the same Venturi
principle of those previously described and provide the same technical
performance. They however differ in their structure.
The vacuum connection U is in fact threaded to allow for assembly

3D drawings are available on vuototecnica.net

of a vacuum cup with male or female support while, on the same axis
but on the opposite side, a hole with metric threading allows for the
generator to be installed directly on the machine or on the cup holders
equipped with springing.
They are fully made with anodised aluminium, with brass ejectors.
Equipped with a vacuum cup, these are they are truly self-contained
gripping units. They are suited for vacuum cup operated loaders or
handlers, for gripping sheet steel, glass slabs, plastic panels and other
similar products.
Upon request, they can be supplied with a high sound suppression
silencer installed on the R exhaust connection.

Item

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 2 M PVP 2 MM1 PVP 2 MM2 PVP 2 MM3 8
Intake air flow rate m3/h 2.8 2.9 3.0 2.9 2.9 3.0 2.8 2.9 3.0 2.8 2.9 3.0
Maximum level of vacuum -KPa 60 70 85 60 70 85 60 70 85 60 70 85
Final pressure mbar abs. 400 300 150 400 300 150 400 300 150 400 300 150
Supply pressure bar 4 5 6 4 5 6 4 5 6 4 5 6
Optimal supply pressure bar 6 6 6 6
Air consumption Nl/s 0.7 0.8 0.9 0.7 0.8 0.9 0.7 0.8 0.9 0.7 0.8 0.9
Operating temperature °C -20 / +80 -20 / +80 -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 78 78 78 78
A G3/8” G3/8” G1/4” -
B M10 M12 M10 M10
Weight g 162 162 162 172
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.33
SINGLE-STAGE VACUUM GENERATORS PVP 2 M, PVP 2 MM1, PVP 2 MM2 and PVP 2 MM3

PVP 2 M
Air flow rate (Nl/s) at differentportata
level of vacuum (-KPa) at optimal supply pressure
0,9
3D drawings are available on vuototecnica.net

0,8

0,7

0,6

0,5

Nl/s
0,4
PVP 2 M portata

0,3
0,9

0,2
0,8
0,1
0,7

0
0,6
0 10 20 30 40 50 60 70 80
-Kpa
0,5
Nl/s

0,4
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
PVP
0,3 2 M temp at optimal supply pressure
item bar Nl/s
0,2
7000
0 10 20 30 40 50 60 70 80 -KPa
PVP 2 M 6.0 0,9 0,1 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 -- 85
PVP 2 MM1 6.0 0,9 6000 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 -- 85
0
PVP 2 MM2 6.0 0,9 5000 0 0.83
10 20 0.70
30 0.65 50
40 0.52
60 70 0.37
80 0.23 0.13 0.07 -- 85
-Kpa
PVP 2 MM3 6.0 0,9 0.83 0.70 0.65 0.52 0.37 0.23 0.13 0.07 -- 85
4000
ms/l

Evacuation rates (ms/lPVP

=s/m
3000 2 M 3) attemp
different levels of vacuums (-KPa) at optimal supply pressure

7000
2000

6000
1000

5000
0
10 20 30 40 50 60 70 80 85
4000 -Kpa
ms/l

3000

2000

1000

0
10 20 30 40 50 60 70 80 85
-Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 2 M 6.0 0,9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2 MM1 6.0 0,9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2 MM2 6.0 0,9 128 257 438 675 1087 1511 2523 4572 6492 85
PVP 2 MM3 6.0 0,9 128 257 438 675 1087 1511 2523 4572 6492 85

ACCESSORIES UPON REQUEST

Silencer item SSX 1/8’’

8.34
SINGLE-STAGE VACUUM GENERATORS PVP 7 SX / SXLP,
PVP 14 SX / SXLP and PVP 18 SX / SXLP
Vacuum generators PVP ... SX/SXLP, operate
making use of the previously described Venturi
principle.
A special new generation silencer installed on

3D drawings are available on vuototecnica.net

them makes them very silent and, thanks to its
shape, prevents them from becoming clogged, also
allowing the suction of saturated fluids of water
condensates or oils, mixed with fine or impalpable
powders.
They are supplied as standard with a vacuum gauge
for reading the level of vacuum. An additional
connection on the body of the generator allows
the installation of a vacuum switch for signalling
the level of vacuum, or of a pneumatic solenoid
valve for a quick restoration of the atmospheric
Compressed air
pressure of use. They are fully made with anodised connection
aluminium, with stainless steel ejectors and screws.
These vacuum generators can be used for
connecting one or more vacuum cups or equipment
with flow rate requirements within the shown values
and can operate in particularly dusty or damp
environments. Available with suction rates between Vacuum
8.3 and 18 m3/h and supply pressure 4-6 bar, for connection
items SX and 1-3 bar for items SXLP.

Additional vacuum
connection

Vacuum Silencer
gauge

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 7 SX PVP 14 SX PVP 18 SX

Intake air flow rate m /h3

9.5 9.5 9.3 14.0 14.0 13.5 18.5 18.5 18.0
Maximum level of vacuum -KPa 60 73 85 60 73 85 60 73 85
Final pressure mbar abs. 400 270 150 400 270 150 400 270 150
Supply pressure bar 4 5 6 4 5 6 4 5 6
Optimal supply pressure bar 6 6 6
Air consumption Nl/s 2.3 2.7 3.2 3.2 4.0 4.8 4.3 5.4 6.4
Operating temperature °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 63 65 67
Weight g 470 480 490

Item PVP 7 SXLP PVP 14 SXLP PVP 18 SXLP

Intake air flow rate m /h3
8.3 9.6 8.8 11.7 14.0 13.6 15.0 18.3 17.5
Maximum level of vacuum -KPa 28 58 88 28 58 88 28 58 88
Final pressure mbar abs.
8
720 420 120 720 420 120 720 420 120
Supply pressure bar 1 2 3 1 2 3 1 2 3
Optimal supply pressure bar 3 3 3
Air consumption Nl/s 2.2 3.4 4.5 3.4 5.2 6.9 4.5 6.6 8.6
Operating temperature °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 67 68 70
Weight g 470 480 490

Spare parts PVP 7 SX / SXLP PVP 14 SX / SXLP PVP 18 SX / SXLP

Sealing kit item 00 15 276 00 15 276 00 15 276
Vacuum gauge item 09 03 15 09 03 15 09 03 15
Silencer item SSX 3/4” R SSX 3/4” R SSX 3/4” R
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.35
SINGLE-STAGE VACUUM GENERATORS PVP 7 SX / SXLP,
PVP 14 SX / SXLP and PVP 18 SX / SXLP

portata Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
3D drawings are available on vuototecnica.net

PVP 7 SX
PVP 7 SXLP
portata

PVP 7 SX PVP 7 SXLP PVP 14 SX PVP 14 SXLP PVP 18 SX PVP 18 SXLP

portata
PVP 14 SX PVP 18 SX
3 4 PVP 18 SXLP 6
PVP 14 SXLP

3,5
2,5 5

3
2 4
2,5
Nl/s

Nl/s
1,5

Nl/s
2 3

1,5
1 2

1
0,5 1
0,5

0 0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 7 SX -Kpa PVP 14 SX -Kpa PVP 18 SX -Kpa
portata
PVP 7 SXLP PVP 14 SXLP PVP 18 SXLP
PVP 7 SX
temp
PVP 7 SXLP
temp
PVP 7 SX temp
PVP 7 SXLP PVP 14 SX
PVP 14 SXLP 2000
PVP 18 SX
3 portata
Air flow rate (Nl/s) at different levels1600
of vacuums (-KPa)
PVP 18 SXLP Max vacuum
Generator Supp. press. Air consumption
1800
3000
portata
at optimal supply pressure
PVP 18 SX
6
2,5 item bar PVP 14 SX
Nl/s 1600
4
PVP 18 SXLP
1400
PVP 14 SXLP
0 10 20 30 40 50 60 70 80 -KPa
1400 1200
2500 3,5 5
2 PVP 7 SX 6.0 3.2 1200
2.58 2.38 2.19 2.02 1.44 0.97 0.86 0.54 0.05 85
PVP 14 SX 6.0 4.8 3 3.75 3.46 3.19 2.95 2.19 1.47
1000
1.29 0.80 0.07 85
ms/l

2000 1000 4
1,5 PVP 18 SX 6.0 6.4 5.00 4.62 4.25 3.93 2.92 1.97 1.75 1.10 0.10 85
ms/l Nl/s

Nl/s ms/l
800
2,5
800
1500 3
600
PVP 7 SXLP 3.0 4.5 600
2.44 2.25 2.07 1.91 1.42 0.95 0.84 0.52 0.04 88
Nl/s

1 2

1000PVP 14 SXLP 3.0 6.9 3.77 3.48 3.20 2.96 2.20 1.48 1.31 0.82 0.07 88
400 400
1,5 2
0,5
PVP 18 SXLP 3.0 8.6 200 4.86 4.48 4.12 3.80 2.82 1.90
200
1.68 1.05 0.09 88
1
500 0 1
0 10 20 30 40 50 60 70 80 85 0
0 10 20 30 40 50 60 70 80 0,5 PVP 14 SX -Kpa 10 20 30 40 50 60 70 80 85
0 PVP 7 SX -Kpa PVP 14 SXLP 0 PVP 18 SX -Kpa
10 PVP
20 7 SXLP
30 40 50 60 70 80 85 0 0 PVP
1018 SXLP
20 30 40 50 60 70 80
PVP 7 SX Evacuation
-Kpa rates (ms/l =s/m3) at0 different
10 20 levels
30 40of vacuums
50 60 70 (-KPa)
80 at optimal supply pressure
-Kpa PVP 18 SX
temp
PVP 7 SXLP PVP 14 SX -Kpa PVP 18 SXLP
PVP 7 SX PVP 14 SXLP
PVP 7 SXLP
temp
temp

3000
PVP 7 SX PVP 7 SXLP PVP 14 SX
2000
PVP 14 SX PVP 14 SXLP PVP 18 SX PVP 18 SX PVP 18 SXLP
PVP 14 SXLP PVP 18 SXLP 1600

1800
1400
2500
1600
1200
1400
2000
1200 1000
ms/l

ms/l

1000
ms/l

1500 800

800
600
1000
600
400
400
500
200 200

0 0 0

8 10 20
PVP 7 SX
30 40 50
-Kpa
60 70 80 85 10 20
PVP 14 SX
30 40 50
-Kpa
60 70 80 85 10 20 30
PVP 18 SX
40
-Kpa
50 60 70 80 85

PVP 7 SXLP PVP 14 SXLP PVP 18 SXLP

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 7 SX 6.0 3.2 33 70 115 173 289 492 796 1418 2532 85
PVP 14 SX 6.0 4.8 23 49 80 120 200 340 550 980 1750 85
PVP 18 SX 6.0 6.4 18 38 62 93 155 264 420 750 1340 85

PVP 7 SXLP 3.0 4.5 34 74 121 200 315 487 760 1348 2410 88
PVP 14 SXLP 3.0 6.9 24 52 85 140 220 340 530 940 1680 88
PVP 18 SXLP 3.0 8.6 18 39 64 105 165 255 398 706 1260 88

8.36
ACCESSORIES FOR SINGLE-STAGE VACUUM GENERATORS

PNEUMATIC COAXIAL SHUTTER VALVES Connector

3D drawings are available on vuototecnica.net

The function of these solenoid valves is to intercept the compressed air supply to the 15 mm 3/2
Solenoid valve
vacuum generators. Interception through an original coaxial shutter allows the supply of
large quantities of air, thus ensuring greater gripping speed of the vacuum cups.

For Ø 8 ext. hose

They are composed of an anodised aluminium body with an integrated coaxial shutter,
pneumatically operated by a micro solenoid
valve with low absorption electric coil, capable of
managing operating pressures between 1.5 and
7 bar.
They can be controlled via vacuum switches or
simple electrical switches.
Thanks to their compactness, it is also
possible to install them directly on the vacuum
generators, thus eliminating unnecessary pipes
and negative volumes.
Manual
drive

A Max flow rate at 6 bar Supply pressure Electrical absorption Weight

Item
Ø l / 1’ bar W g
VPE 00 NC V24CC G1/8” 350 1.5 ÷ 7 2 110
VPE 00 NO V24CC G1/8” 350 1.5 ÷ 7 2 110
VPE 01 NC V24CC G1/4” 500 1.5 ÷ 7 2 100
VPE 01 NO V24CC G1/4” 500 1.5 ÷ 7 2 100
VPE 02 NC V24CC G3/8” 600 1.5 ÷ 7 2 100
VPE 02 NO V24CC G3/8” 600 1.5 ÷ 7 2 100
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

PNEUMATIC SLEEVE VALVE

For Ø 6 ext. hose

This particular sleeve valve has been constructed to ensure

a faster restoration of the atmospheric pressure inside the
vacuum cups when the load is disconnected. When it is
pneumatically operated at the end of the cycle, it closes
the generator discharge connection, conveying the supply
air in the connection of use. In this way, the vacuum cups
are immediately detached. It is suitable for generators with
capacities not exceeding 15 m3/h and designed especially
for series MSVE.
It is made of anodised aluminium, with an integrated
silicone sleeve membrane.
8

Max flow rate of free mouth Servo-control pressure Weight

Item
l / 1’ bar g
07 02 90 600 3÷8 230
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.37
FIXING SUPPORTS FOR SINGLE-STAGE VACUUM GENERATORS

The supports illustrated and described on this page are made in anodised aluminium as a
standard but, upon request, they can be supplied in the stainless steel version.
These supports are for fixing the multi-stage vacuum generators to the machine via a
cylindrical slotted pin or a ball pin housed in the machine itself.
3D drawings are available on vuototecnica.net

They are suited for robotic gripping systems and they allow for easy vacuum generator
installation on the profiles used in the automotive sector.

By Material Weight
Item
generators g
FCH 01 PVP 2 aluminium 60
PVP 3
FCH 01 INOX PVP 2 stainless steel 180
PVP 3

By Material Weight
Item
generators g
8
FCH 02 15 01 10 aluminium 72
15 02 10
15 03 10
15 04 10
15 05 10
15 06 10
15 07 10
FCH 02 INOX 15 01 10 stainless steel 220
15 02 10
15 03 10
15 04 10
15 05 10
15 06 10
15 07 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
8.38
FIXING SUPPORTS FOR SINGLE-STAGE VACUUM GENERATORS

3D drawings are available on vuototecnica.net

By Material Weight
Item
generators g
FCH 03 PVP 2 aluminium 39
PVP 3
FCH 03 INOX PVP 2 stainless steel 117
PVP 3

By Material Weight
Item
generators g
8
FCH 04 15 01 10 aluminium 52
15 02 10
15 03 10
15 04 10
15 05 10
15 06 10
15 07 10
FCH 04 INOX 15 01 10 stainless steel 156
15 02 10
15 03 10
15 04 10
15 05 10
15 06 10
15 07 10

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
8.39
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS, MSVE SERIES

The vacuum generators of this new series can fully drive a negative pressure gripping system. By means of coaxial
shutters, the original compressed air supply system feeds large quantities of air to both the ejectors and the ejection
system, thereby ensuring faster gripping and release of the load. These vacuum generators are equipped with single-
stage ejectors, are powered by low pressure (max. 4 bar), and feature an extremely high emptying speed in
3D drawings are available on vuototecnica.net

relation to their suction flow rate. All this allows for increasingly faster high-performance work
cycles. Two micro solenoid valves manage the compressed air supply to the vacuum
ejector and adjustable discharge blow off. The intensity and duration of the latter are
managed through a screw-type flow regulator. The check valve built into the suction
connector maintains the vacuum in the event of a power outage. A digital vacuum
switch, equipped with a display and commutation LED, manages the compressed
air supply and provides a signal to start a cycle under safety conditions. An anodised
aluminium distributor with vacuum connectors has an integrated suction filter that can be
easily inspected. By activating the compressed air power micro solenoid valve, the generator
creates vacuum for use. As soon as the set maximum value is reached, the digital vacuum switch acts on
the electric coil of the micro solenoid valve and stops the air supply, reactivating it when the vacuum falls
below the minimum level. 2 Solenoid valves
Besides maintaining the vacuum level within set safety values (hysteresis), this modulation with manual drive

allows for considerable compressed air savings. A second signal from the vacuum switch
(also adjustable and independent with respect to the first) can be used to start
the cycle when the vacuum level reached is suitable for use. Once the
work cycle is completed, the micro solenoid valve that supplies
compressed air to the generator is deactivated while, at the
same time, the ejection solenoid valve is activated for quick
restoration of the atmospheric pressure upon use. The
MSVE vacuum generators can be installed in any position Silencer
and are suitable for suction gripping systems, handling
metal sheets, glass, marble, ceramics, plastic, cardboard, Screw-type
wood, etc. and, in particular, for the industrial robotics flow regulator
Blow off
sector, where equipment with excellent performance and
limited weight and bulk are increasingly required.

Additional vacuum Digital vacuum switch

connection G3/8” Item 123010

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item MSVE 3 MSVE 5
Intake air flow rate m /h
3
2.6 2.8 3.0 4.9 5.1 5.1
Maximum level of vacuum -KPa 40 61 85 40 61 85
Final pressure mbar abs. 600 390 150 600 390 150
Supply pressure bar 2 3 4 2 3 4
Air consumption Nl/s 0.7 0.9 1.2 1.3 1.7 2.2
Max quantity of air blown at 4 bar l/min 650 650
Internal coaxial shutter position
of supply NO NO
Supply solenoid valve absorption W 2.0 2.0
Internal coaxial shutter position
of ejection NC NC
Ejection solenoid valve absorption W 2.0 2.0
Supply voltage V 24DC 24DC
8 Vacuum switch output PNP PNP
Degree of protection IP 40 40
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 48 44
Weight g 493 493

Spare parts MSVE 3 MSVE 5

Sealing kit item 00 15 503 00 15 503
Digital vacuum switch item 12 30 10 12 30 10
NO supply solenoid valve item 00 07 304 00 07 304
NC supply
and blowing solenoid valve item 00 15 447 00 15 447
Silencer item SSX 1/8” SSX 1/8”
Note: To order a generator with NC supply coaxial shutter, use item code MSVE..NC.
To order a generator without a digital vacuum switch, use item code MSVE..SV.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.40
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 3 and MSVE 5

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
FVG3 portata FVG5 portata

0,9
MSVE 3 MSVE 5
1,6

0,8
1,4

0,7
1,2
0,6
1
0,5 FVG5 portata
FVG3 portata

Nl/s
Nl/s

0,8
0,4
0,6
1,6
0,9
0,3

0,8 0,4
1,4
0,2

0,7
0,1 0,2
1,2

0,60 0
1
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0,5 -Kpa -Kpa
Nl/s
0,8
Nl/s

0,4
0,6
0,3
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator
FVG3 temp Supp. press. Air consumption FVG5 temp
at
0,4optimal supply pressure
item
0,2 bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
0,2
0,1
MSVE
10000 3 4.0 1.2 0.83 0.67 0.63 50000.56 0.49 0.41 0.34 0.18 0.08 85
MSVE
0 5
9000 4.0 2.2 1.39 1.22 1.11 0 1.00
4500
0.90 0.69 0.44 0.30 0.16 85
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
8000 -Kpa 4000 -Kpa

7000 3500
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
6000 3000
FVG3 temp FVG5 temp
ms/l
ms/l

5000 2500

4000 MSVE 3 2000 MSVE 5

10000 5000
3000 1500
9000 4500
2000 1000
8000 4000
1000 500
7000 3500
0 0
6000 10 20 30 40 50 60 70 80 85 3000 10 20 30 40 50 60 70 80 85
-Kpa -Kpa
ms/l

2500
ms/l

5000

4000 2000

3000 1500

2000 1000

1000 500 8
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.41
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 8 and MSVE 12
3D drawings are available on vuototecnica.net

2 Solenoid valves with

Silencer manual drive

Screw-type
flow regulator
Blow off

Additional vacuum Digital vacuum switch

connection G3/8” Item 123010

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item MSVE 8 MSVE 12
Intake air flow rate m /h
3
8.0 8.6 8.8 12.0 12.2 12.5
Maximum level of vacuum -KPa 40 60 90 40 60 90
Final pressure mbar abs. 600 400 100 600 400 100
Supply pressure bar 2 3 3.5 2 3 3.5
Air consumption Nl/s 2.8 3.8 4.3 3.7 5.0 5.5
Max quantity of air blown at 3.5 bar l/min 600 600
Internal coaxial shutter position
of supply NO NO
Supply solenoid valve absorption W 2.0 2.0
Internal coaxial shutter position
of ejection NC NC
Ejection solenoid valve absorption W 2.0 2.0
Supply voltage V 24DC 24DC
8 Vacuum switch output PNP PNP
Degree of protection IP 40 40
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 53 50
Weight g 580 620

Spare parts MSVE 8 MSVE 12

Sealing kit item 00 15 504 00 15 504
Digital vacuum switch item 12 30 10 12 30 10
NO supply solenoid valve item 00 07 304 00 07 304
NC supply
and blowing solenoid valve item 00 15 447 00 15 447
Silencer item SSX 3/8” SSX 3/8”
Note: To order a generator with NC supply coaxial shutter, use item code MSVE..NC.
To order a generator without a digital vacuum switch, use item code MSVE..SV.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.42
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 8 and MSVE 12

MSVE 8 portata MSVE 12 portata

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure

3
MSVE 8 4
MSVE 12

3,5
2,5

3
2
MSVE 8 portata
2,5
Nl/s

Nl/s
1,5 MSVE 12 portata
2

1,5
3
1

2,5 4
0,5
0,5
3,5
2
0 0
0 10 20 30 40 50 60 70 80 3 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
Nl/s

1,5
2,5
MSVE 12 temp
Nl/s

1
2
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
MSVE 8 temp Generator Supp. press. Air consumption
at optimal supply pressure
2500
item bar Nl/s 1,5
0 10 20 30 40 50 60 70 80 -KPa
0,5
3000
MSVE 8 3.5 4.3 2.44 2.27 2.11 1 1.94
2000
1.72 1.46 0.98 0.50 0.04 90
MSVE 12 3.5 5.5 3.47 2.88 2.72 2.50 2.27 1.83 1.16 0.60 0.05 90
0 0,5
2500 0 10 20 30 40 50 60 70 80
-Kpa 1500
0
2000 0 10 20 30 40 50 60 70 80
ms/l

-Kpa
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
1000
ms/l

MSVE 8 temp 1500

MSVE 12 temp

1000
MSVE 8 500
MSVE 12
3000 2500

500
2500 0
2000
10 20 30 40 50 60 70 80 85
-Kpa
0
2000
10 20 30 40 50 60 70 80 85
1500
-Kpa
ms/l

ms/l

1500

1000
1000

500
500
8
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.43
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 20
3D drawings are available on vuototecnica.net

Silencer 2 Solenoid valves with

manual drive

Additional vacuum Digital vacuum switch

connection G1/2” Item 123010

Screw-type
flow regulator
Blow off

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item MSVE 20
Intake air flow rate m /h
3
18 19 20
Maximum level of vacuum -KPa 40 60 90
Final pressure mbar abs. 600 400 100
Supply pressure bar 2 3 4
Air consumption Nl/s 4.9 6.6 8.0
Max quantity of air blown at 4 bar l/min 650
Internal coaxial shutter position
of supply NO
Supply solenoid valve absorption W 2.0
Internal coaxial shutter position
of ejection NC
Ejection solenoid valve absorption W 2.0
Supply voltage V 24DC
8 Vacuum switch output PNP
Degree of protection IP 40
Temperature of use °C -10 / +60
Noise level at
optimal supply pressure dB(A) 70
Weight kg 1.04

Spare parts MSVE 20

Sealing kit item 00 15 560
Digital vacuum switch item 12 30 10
NO supply solenoid valve item 00 07 304
NC supply
and blowing solenoid valve item 00 15 447
Silencer item SSX 1/2”
Note: To order a generator with NC supply coaxial shutter, use item code MSVE..NC.
To order a generator without a digital vacuum switch, use item code MSVE..SV.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.44
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MSVE 20

150710SX portata

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure

4
Nl/s

150710SX portata

1
6

0
5 0 10 20 30 40 50 60 70 80
-Kpa

4
150710SX temp
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
Nl/s

3
1400
item bar Nl/s
0 10 20 30 40 50 60 70 80 -KPa
MSVE 20 4 82
1200 5.55 5.00 4.44 4.16 3.83 3.00 1.97 1.56 0.85 90

1000
1

800
0
ms/l

0 10 20 30 40 50 60 70 80
600 -Kpa
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
400
150710SX temp

200
1400

0
1200 10 20 30 40 50 60 70 80 85
- Kpa
1000

800
ms/l

600

400

8
200

0
10 20 30 40 50 60 70 80 85
- Kpa

8.45
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND MULTI-FUNCTION VACUUM
GENERATORS, SERIES MSVE
3D drawings are available on vuototecnica.net

Connector for suction sol enoid va lve

Blowing Red
Blue
va lve
Connector for blowing sol enoid va lve

Suction
va lve

Connector for
vacuum switch
8

Digital
vacuum switch

8.45-1
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND
MULTI-FUNCTION VACUUM GENERATORS, SERIES MSVE

3D drawings are available on vuototecnica.net

Cable set with built-in energy saving device

WHITE
DIGITAL OUTPUT (+24) DIGITAL VACUUM SWITCH
PNP ITEM 121010 (C)
BROWN
POSITIVE POLE +24

GREY CONNECTION SUPPLY SOLENOID VALVE

NEGATIVE POLE - 0 V
DISTRIBUTOR NC (A)
BLACK
SUCTION ON +24 V
BLUE BLOWING SOLENOID VALVE
BLOWING ON +24 V NC (B)

Item Description
00 15 203 Set of cables with built-in energy saving device for connection to:
- Digital vacuum switch
- NC micro supply solenoid valve
- NC micro ejection solenoid valve
Cable length - 5 m

Connector

Item Description
00 15 157 Connector with LED for micro solenoid valves

Cable with axial connector

Item Description
00 12 20 Electrical connection cable with M8 - 4 pin axial connector 8
for digital vacuum switch length 5 m

Cable with radial connector

Item Description
00 12 21 Electrical connection cable with M8 - 4 pin radial connector
for digital vacuum switch length 5 m

8.46-1
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND
MULTI-FUNCTION VACUUM GENERATORS, SERIES MSVE
3D drawings are available on vuototecnica.net

M an u a l
a c t i va t i o n

NO micro supply solenoid valve

Item Description

00 07 304 NO micro solenoid valves with built-in low absorption electrical coil and interface

M an u a l
a c t i va t i o n

NC supply and blowing micro solenoid valve

Item Description

00 15 447 NC micro solenoid valves with built-in low absorption electrical coil and interface

8
Digital vacuum switch

Item Description
12 30 10 Digital vacuum switch

8.47-1
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS SERIES AVG - GENERAL
DESCRIPTION
These generators are independent vacuum units capable of driving a vacuum gripping system They have
been specially designed for the AUTOMOTIVE sector and they are equipped with single ejectors that, given
the same flow rate as the multi-ejector generators, allow for a quicker grip.
They are provided as standard with a built-in pneumatic energy-saving device.
3D drawings are available on vuototecnica.net

They are composed of an anodised aluminium mono-block structure, inside of which are installed the
ejectors, the servo-controlled slide valve for the compressed air supply and are contained the vacuum
chambers as well as the various connections.
The following are instead installed on the outside:
- A bistable impulse solenoid valve for controlling the slide valve.
- A solenoid valve for blowing the ejected compressed air.
- A flow regulator for dosing the ejected compressed air.
- Two silencers for removing noise from the ejected air.
- An aluminium manifold provided with vacuum connections with built-in:
• A pneumatic vacuum switch for managing the compressed air supply according to the set level of
vacuum (energy saving).
• A check valve for maintaining the vacuum in case of electricity or compressed air failure.
• A suction filter, easy to inspect through the transparent polycarbonate lid.

OPERATION
By providing an electric impulse to the two-position solenoid valve, the compressed air supply slide valve
will be activated and vacuum will be created at the application. Once the preset maximum value has been
reached, the pneumatic vacuum switch acts on the servo-controlled valve and interrupts the compressed
air supply, restoring it when the value returns below the minimum value.
Besides maintaining the level of vacuum within preset safety values, this modulation also allows a
considerable saving of compressed air and occurs even in the absence of electricity. Once the work cycle
is completed, the power supply solenoid valve is deactivated by means of an electrical pulse while, at the
same time, the ejection solenoid valve is activated for quick restoration of the atmospheric pressure of use.
AVG vacuum generators are fitted for the installation of a digital vacuum switch. Also these vacuum
generators can be installed in any position.

SECTORS OF USE
AVG vacuum generators are suitable for suction gripping systems, for the handling of metal sheets, glass,
marble, ceramics, plastic, cardboard, wood, etc. and, in particular, for the AUTOMOTIVE sector, where
equipment with excellent performance and limited size and weight are increasingly required.

8.46
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS AVG 18 and AVG 25

3D drawings are available on vuototecnica.net

For Ø 4 ext. hose
For Ø 4 ext. hose

Digital vacuum switch

Item 12 05 11

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item AVG 18 AVG 25
Intake air flow rate m3/h 16.5 17.0 17.4 24.5 25.0 25.2
Maximum level of vacuum -KPa 60 70 85 60 70 85
Final pressure mbar abs. 400 300 150 400 300 150
Supply pressure bar 4 5 6 4 5 6
Optimal supply pressure bar 6 6 8
Air consumption Nl/s 4.3 5.3 6.4 6.5 8.0 9.6
Max quantity of air blown at 6 bar l/min 140 140
Bistable supply solenoid valve NO/NC NO/NC NO/NC
Electrical absorption W 1 1
Ejection solenoid valve position NC NC NC
Electrical absorption W 4 4
Supply voltage V 24DC 24DC
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 63 65
Weight Kg 1.67 1.67
Note: To order a generator with a digital vacuum switch installed, add the letter V to the item code (example: AVG 25 V).
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.47
SINGLE-STAGE AND MULTI-FUNCTION VACUUM GENERATORS AVG 18 and AVG 25

AVG18 portata AVG25 portata

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure

AVG 18 AVG 25
3D drawings are available on vuototecnica.net

6 8

7
AVG18
5 portata AVG25 portata

4
5
6 8

Nl/s
Nl/s

3 4
7
5
3
2 6

4 2
5
1
1

Nl/s
Nl/s

3 4

0 0
0 10 20 30 40 50 60 70 80 3 0 10 20 30 40 50 60 70 80
2 -Kpa
-Kpa
2

1 AVG25 tempi
AVG18 temp Air flow rate (Nl/s)1 at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item0 bar Nl/s 0
0 10 20 30 40 50 60 70 0
80 10 20 30 0 40
10 2050 30 60
40 50 70 60 80
70 80 -KPa
-Kpa -Kpa
AVG 18 6.0 6.4 4.83 4.58 4.04 3.58 2.72 1.90 1.68 1.07 0.10 85
AVG 25 6.0 9.6 7.00 6.63 5.86 5.18 3.94 2.76 2.44 1.54 0.15 85
AVG25 tempi
AVG18
1200 temp 900

800
1000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
700

800

1200
AVG 18 600
AVG 25
900
500
ms/l
ms/l

600
800
400
1000

400 700
300

800 600
200
200
500
100
ms/l
ms/l

600
400
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
400 300
-Kpa -Kpa

200
200
100

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

ACCESSORIES AND SPARE PARTS UPON REQUEST

Item AVG 18 AVG 25
Sealing kit item 00 KIT AVG 18 00 KIT AVG 25
Exhaust silencers item SSX 3/4 R
Digital micro vacuum switch item 12 05 11 *
Bistable supply solenoid valve item 00 15 297
NC blowing solenoid valve item 00 15 175
* Complete the code indicating the electrical type of the output: P = PNP; N = NPN

8.48
ACCESSORIES AND SPARE PARTS FOR SINGLE-STAGE AND MULTI-FUNCTION VACUUM
GENERATORS, SERIES AVG

3D drawings are available on vuototecnica.net

Connector for
blowing solenoid
valve

Connector for supply

Blowing solenoid
solenoid valve
valve

Supply solenoid
valve

Silencer

Pneumatic
vacuum switch

Digital micro vacuum

switch

8.49
ACCESSORIES AND SPARE PARTS FOR SINGLE-STAGE AND MULTI-FUNCTION VACUUM
GENERATORS, SERIES AVG
3D drawings are available on vuototecnica.net

Digital micro vacuum switch

Item Description
12 05 11 * Digital micro vacuum switch
* Complete the code indicating the electrical type of the output: P = PNP; N = NPN

Connector

Item Description
00 15 157 Connector with LED for solenoid valves

Bistable solenoid valve

Item Description
00 15 297 Bistable supply solenoid valve

NC solenoid valve

Item Description
00 15 175 NC blowing solenoid valve
8

Silencer

Item Description
SSX 3/4” R Exhaust silencer

8.50
MULTI-STAGE VACUUM GENERATORS - GENERAL DESCRIPTION

Our multi-stage vacuum generators produce a maximum vacuum of 90%, equal to a final
level of vacuum of 100 mbar abs., with different suction capacities. They operate by use
of compressed air from 1 to 6 bar.
Working principle

3D drawings are available on vuototecnica.net

Each ejector is based on the Venturi principle: the supply fluid (compressed air) is led
high speed by a convergent pipe into the fluid to be extracted (volume of the air to be
sucked). This mixture is then led into two or three divergent pipes, where its kinetic
energy is transformed into pressure energy for it to enter in the environment at a higher
pressure (atmospheric pressure at the exhaust).
Technical features
The main asset of multi-stage vacuum generators is its ability to exploit the kinetic
energy of the supply compressed air via several specially dimensioned in-line ejectors,
before releasing it in the atmosphere. This system allows, given the same flow rate, a
reduced compressed air consumption compared to the single-stage vacuum generators.
The suction flow rate is indirectly proportional to the differential between the pressure of
the fluid to be sucked and the external (atmospheric) pressure.
The reduced size and weight make multi-stage vacuum generators compact in relation to
their great suction flow rate.
The absence of moving parts make them particularly silent and allow them to be used
continuously, without developing heat.
Being supplied exclusively by compressed air, these vacuum generators are explosion-
proof and can be used in work environments with temperatures ranging from -20 to
+80°C.
They are fully made with stainless materials.
Thanks to all these features, a good filtration of the supply and sucked compressed air is
sufficient to make these generators are fully maintenance-free.

P = Compressed air connection

R = Air exhaust
U = Vacuum connection

8.51
MULTI-STAGE VACUUM GENERATORS SERIES M

These new design vacuum generators feature multiple state of the

art ejectors assembled onto small modules. One of their distinctive
features is their great suction flow rate compared to their reduced
size.
3D drawings are available on vuototecnica.net

With a compressed air supply of 4 - 5 bar, they can produce a

maximum vacuum equal to 85% and a suction flow rate of
3.6 - 18 m3/h, according to the number of modules.
The silencer is built-in.
They are fully made with slightly anodised alloys and can be installed
in any position. The multi-stage vacuum generators in this range
are suited for interconnecting vacuum cup gripping systems and, in
particular, in the industrial robotics sector, which requires equipment
with excellent working performance, but with weight and size reduced
to the minimum.

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item M3 M7

Intake air flow rate m /h3

3 3.4 3.6 5.4 5.8 6.2
Maximum level of vacuum -KPa 62 82 85 62 82 85
Final pressure mbar abs. 380 180 150 380 180 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 0.5 0.7 0.8 0.8 1.2 1.4
Operating temperature °C -10 / +80 -10 / +80
8
Noise level at
optimal supply pressure dB(A) 64 70
Weight g 109 111
A 24.5 25.5
B 9 10
C 4.5 4.5
E Ø 20 24
F 11 12
G Ø G1/4” G3/8”

Spare parts M3 M7
Sealing kit and reed valves item 00 KIT M 3 00 KIT M 7
Exhaust silencer item 00 15 150 00 15 150
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.52
MULTI-STAGE VACUUM GENERATORS M 3 and M 7

M3 portata
M7 portata

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure

M3 M7
1,2
M3 M7
2

1,8
1
1,6

M3 portata 1,4
0,8
M7 portata
1,2

Nl/s
Nl/s

0,6
M3 1

1,2 0,8 M7
0,4 2
0,6

1 1,8
0,4
0,2
1,6
0,2
0,8
1,4
0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
1,2
-Kpa -Kpa
Nl/s

0,6 Nl/s
1
M3 tempi
M7 tempi
0,4 0,8
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption 0,6
at optimal supply pressure
item
0,2 bar Nl/s
0 10 20 0,4 30 40 50 60 70 80 -KPa
M7
M3
0
5.0 M3 0.8 1.00 0.83 0.61 0,20.34
7000
0.18 0.12 0.10 0.07 0.03 85
M7 0 10 5.0
20 30 40 501.4 60 70 1.7280 1.28 0.89 0
0.50 0.37 0.27 0.16 0.11 0.05 85
12000
-Kpa 0 10 20 30 40 50 60 70 80
6000 -Kpa
M3 tempi
10000
5000M7 tempi

8000
Evacuation rates (ms/l =s/m3) at different levels of4000
vacuums (-KPa) at optimal supply pressure
ms/l
ms/l

6000
M3 3000 M7
M3 7000
M7
12000
4000 2000

6000
10000 1000
2000
5000
0
8000
0 10 20 30 40 50 60 70 80 85
10 20 30 40 50 60 70 80 85 4000 -Kpa
ms/l
ms/l

6000 -Kpa

3000

4000
2000

2000
8
1000

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.53
MULTI-STAGE VACUUM GENERATORS M 10, M 14 and M 18
3D drawings are available on vuototecnica.net

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item M 10 M 14 M 18
Intake air flow rate m /h3
7.7 8.5 9.4 10.2 11.6 12.6 14.8 16.5 18.0
Maximum level of vacuum -KPa 62 82 85 62 82 85 62 82 85
Final pressure mbar abs. 380 180 150 380 180 150 380 180 150
Supply pressure bar 3 4 5 3 4 5 3 4 5
8
Optimal supply pressure bar 5 5 5
Air consumption Nl/s 1.2 1.6 1.9 1.7 2.1 2.5 2.3 2.9 3.6
Operating temperature °C -10 / +80 -10 / +80 -10 / +80
Noise level at
optimal supply pressure dB(A) 72 72 76
Weight g 144 145 150
A 34.5 34.5 44.5
B 20 20 30
C 4.5 4.5 4.5

Spare parts M 10 M 14 M 18
Sealing kit and reed valves item 00 KIT M 10 00 KIT M 14 00 KIT M 18
Exhaust silencer item N°2 00 15 150 N°2 00 15 150 N°3 00 15 150
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.54
MULTI-STAGE VACUUM GENERATORS M 10, M 14 and M 18

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
M18 portata
M10 portata M14 portata

3
MM10
10 4
MM14
14 6
MM1818
3,5
2,5 5
3

2 4
2,5

1,5 Nl/s 2 3

Nl/s
Nl/s

1,5
1 2

1
M18 portata
0,5 1
0,5
M10 portata M14 portata
0 0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa -Kpa M18
-Kpa
M10 M14 6
M10 temp M18 temp
3 4 temp
M14
5
3,5
2,5

Air flowM14
3
M10 4
rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
2 Generator Supp. press. Air consumption M18
4500
3500
2,5 at optimal supply pressure
item bar Nl/s 3

Nl/s
0 10 20 30 40 50
2500
60 70 80 -KPa
Nl/s

1,5 2
Nl/s

4000 3000

3500 M 10 5.0 1.9 1,5

2.61 2.00 1.55 0.80 0.64 0.502 0.29 0.19 0.09 85
1 2000
M 14 5.0 2.5 2500
3.50 2.33 1.72 1.00 0.89 0.67 0.35 0.24 0.11 85
3000
M 18 5.0 3.6 1
2000
5.00 3.50 2.78 2.02 1.02 0.751 0.44 0.30 0.14 85
0,5
2500 1500
ms/l

0,5
ms/l

1500 0
2000
ms/l

0 0 10 20 30 40 50 60 70 80
0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 1000 -Kpa
1500
-Kpa 1000
-Kpa M18 temp
1000
M10 temp 3
) at different levels of vacuums (-KPa) at500optimal supply pressure
Evacuation rates (ms/l =s/m500
500 M14 temp

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
0
-Kpa -Kpa 10 20 30 40 50 60 70 80 85

4500
MM10
10 3500
MM14
14 2500
M18
M 18
-Kpa

4000
3000
2000
3500
2500
3000
1500
2000
2500
ms/l

ms/l
ms/l

2000 1500
1000
1500
1000
1000 500
500
500
8
0 0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
M 10 5.0 1.9 40 93 188 371 629 918 1534 2731 3878 85
M 14 5.0 2.5 30 69 140 276 469 685 1144 2036 2892 85
M 18 5.0 3.6 21 48 98 193 327 478 799 1423 2020 85

8.55
MULTI-STAGE VACUUM GENERATORS SERIES M.. SSX

These vacuum generators share the same technical features as the others of the M
series described above. Their distinctive feature is their silent operation.
In fact, along with the built-in silencer, they also have an external SSX silencer for a
further noise reduction.
3D drawings are available on vuototecnica.net

These generators are particularly recommended in work environments where the noise
level must be kept within very low values.

Silencer

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item M 3 SSX M 7 SSX

Intake air flow rate m3/h 3.0 3.4 3.6 5.4 5.8 6.2
Maximum level of vacuum -KPa 62 82 85 62 82 85
Final pressure mbar abs. 380 180 150 380 180 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 0.5 0.7 0.8 0.8 1.2 1.4
Operating temperature °C -10 / +80 -10 / +80
Noise level at
optimal supply pressure dB(A) 52 58
8
Weight g 109 111
A 24.5 25.5
B 9 10
C 4.5 4.5
E Ø 20 29
F 11 12
G Ø G1/4” G3/8”
H 74.5 97.5

Spare parts M 3 SSX M 7 SSX

Silencer item SSX 1/4” SSX 3/8”
Exhaust silencer item 00 15 150 00 15 150
Sealing kit and reed valves item 00 KIT M 3 00 KIT M 7
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.56
MULTI-STAGE VACUUM GENERATORS M 3 SSX and M 7 SSX

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
M7 SSX portata
M3 SSX portata

M3 SSX M7 SSX
M 3 SSX M 7 SSX
1,2 2

1,8
1
1,6

1,4
0,8
1,2
Nl/s

0,6 1

Nl/s
M3 SSX portata
M7 SSX
0,8 portata
0,4
M3 SSX 0,6

1,2 0,4
M7 SSX
0,2
2
0,2
1 1,8
0 0
0 10 20 30 40 50 60 70 80 1,6 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
0,8 1,4

M7 SSX
1,2 temp
Nl/s

M30,6
SSX temp
1
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Nl/s

Generator Supp. press. Air consumption

0,4 at0,8
optimal supply pressure
item bar Nl/s
0 10 20 0,630 40 50 M 760S S X 70 80 -KPa
M3 SSX
0,2 5.0
M3 SSX 0.8 1.00 0.83 0.61 0.34
0,4 0.18 0.12 0.10 0.07 0.03 85
7000
M 712000
SSX 5.0 1.4 1.72 1.28 0.89 0.50
0,2
0.37 0.27 0.16 0.11 0.05 85
0 6000
0 10 20 30 40 50 60 70 80 0
10000
-Kpa 0 10 20 30 40 50 60 70 80
5000 -Kpa

8000
4000
M7 SSX temp
M3 SSX temp
Evacuation rates (ms/l =s/m ) at different levels of vacuums (-KPa) at optimal supply pressure
3
ms/l
ms/l

6000 3000

4000 2000
M3 SSX M7 SSX
M 3 SSX 1000
M 7 SSX
12000 7000
2000

0
6000
10000 10 20 30 40 50 60 70 80 85
0
10 20 30 40 50 60 70 80 85 -Kpa
-Kpa 5000
8000

4000
ms/l

6000
ms/l

3000

4000
2000

2000
8
1000

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

8.57
MULTI-STAGE VACUUM GENERATORS M 10 SSX, M 14 SSX and M 18 SSX
3D drawings are available on vuototecnica.net

Silencer

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item M 10 SSX M 14 SSX M 18 SSX

Intake air flow rate m /h3

7.7 8.5 9.4 10.2 11.5 12.6 14.8 16.5 18.0
Maximum level of vacuum -KPa 62 82 85 62 82 85 62 82 85
Final pressure mbar abs. 380 180 150 380 180 150 380 180 150
Supply pressure bar 3 4 5 3 4 5 3 4 5
Optimal supply pressure bar 5 5 5
Air consumption Nl/s 1.2 1.6 1.9 1.7 2.1 2.5 2.3 2.9 3.6
Operating temperature °C -10 / +80 -10 / +80 -10 / +80
Noise level at
8 optimal supply pressure dB(A) 60 62 66
Weight g 144 145 150
A 34.5 34.5 44.5
B 20 20 30
C 4.5 4.5 4.5
E Ø 29 29 35
G Ø G3/8” G3/8” G1/2”
H 106.5 106.5 136.5

Spare parts M 10 SSX M 14 SSX M 18 SSX

Silencer item SSX 3/8” SSX 3/8” SSX 1/2”
Exhaust silencer item N°2 00 15 150 N°2 00 15 150 N°3 00 15 150
Sealing kit and reed valves item 00 KIT M 10 00 KIT M 14 00 KIT M 18
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.58
MULTI-STAGE VACUUM GENERATORS M 10 SSX, M 14 SSX and M 18 SSX

3D drawings are available on vuototecnica.net

Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure

M14 SSX portata M18 SSX portata

M10 SSX portata

3
M M10 SSX
10 SSX MM14 SSX
14 SSX 6
MM18
18 SSX
SSX
4

3,5
2,5 5

2 4
2,5
Nl/s

Nl/s

Nl/s
1,5 2 3

1,5
1 2

0,5 1
0,5
M14 SSX portata M18 SSX portata
M10 SSX portata
0 0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
M10-KpaSSX M14-KpaSSX M18-KpaSSX
3 4 6
M18 SSX tempi
M10 SSX tempi M14 SSX tempi
3,5
2,5 5

3
2
Air flow rate (Nl/s) at different levels of4 vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
2,5
M10 SSX M14 SSXat optimal supply pressure M18 SSX
item bar Nl/s
Nl/s

Nl/s

1,5

Nl/s
2 3
4500 3500 0 10 20 30 40 50
2500 60 70 80 -KPa
1,5
4000
1 M 10 SSX 5.0 1.9 3000 2.61 2.00 1.55 0.80 0.64 0.502 0.29 0.19 0.09 85
3500 M 14 SSX 5.0 2.5 1 3.50 2.33 1.72 1.00 0.89 0.67
2000 0.35 0.24 0.11 85
0,5 M 18 SSX 5.0 3.6 2500 5.00 3.50 2.78 2.02 1.02 0.751 0.44 0.30 0.14 85
3000 0,5
1500
2000
2500
0 0 0
ms/l
ms/l

ms/l

0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
2000 -Kpa 1500 -Kpa -Kpa
1000
1500 M18 SSX tempi
M10 SSX tempi M14 SSX
1000 tempi
1000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
500
500
500

0 0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
10 20 30
M10
40
SSX
50 60 70 80 85

4500
M 10 SSX-Kpa
3500
M14-KpaSSX
M 14 SSX 2500
MM18
18 SSX
SSX
-Kpa

4000
3000
2000
3500
2500
3000
1500
2500 2000
ms/l

ms/l

2000 1500
1000
1500
1000
1000
500
500
500 8
0 0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
M 10 SSX 5.0 1.9 40 93 188 371 629 918 1534 2731 3878 85
M 14 SSX 5.0 2.5 30 69 140 276 469 685 1144 2036 2892 85
M 18 SSX 5.0 3.6 21 48 98 193 327 478 799 1423 2020 85

8.59
FIXING SUPPORTS FOR MULTI-STAGE VACUUM GENERATORS, SERIES M

The supports illustrated and described on this page are made in anodised aluminium as
a standard but, upon request, they can be supplied in the stainless steel version.
These supports are for fixing the multi-stage vacuum generators of the series M to the
machine via a cylindrical slotted pin or a ball pin housed in the machine itself.
3D drawings are available on vuototecnica.net

They are suited for robotic gripping systems and they allow for easy vacuum generator
installation on the profiles used in the automotive sector.

By Material Weight
Item
generators g
00 FCH 23 M 3 - M 7 - M 10 - M 14 - M 18 aluminium 63
00 FCH 22 M 3 - M 7 - M 10 - M 14 - M 18 stainless steel 191

By Material Weight
Item
generators g
00 FCH 13 M 3 - M 7 - M 10 - M 14 - M 18 aluminium 85
00 FCH 12 M 3 - M 7 - M 10 - M 14 - M 18 stainless steel 256

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
8.60
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS SERIES MVG - GENERAL
DESCRIPTION
These generators are true independent vacuum units that can control an entire vacuum
gripping system. Their distinctive features are their compact size and great suction flow
rate.
They are composed of a mono-block anodised aluminium structure onto which are

3D drawings are available on vuototecnica.net

assembled:
- A modular and silenced multi-stage vacuum generator.
- A micro solenoid valve for supplying compressed air to the generator.
- A micro solenoid valve for blowing the exhaust compressed air.
- An adjustable flow regulator for dosing the exhaust air.
- A unidirectional check valve, located on the suction inlet, for maintaining the vacuum in
case of electricity failure.
- A digital vacuum switch provided with display and commutation LEDs, for managing the
compressed air supply and for signalling the safety cycle start-up.
- An anodised aluminium manifold provided with vacuum connections and a built-in filter
easy to inspect.
By activating the compressed air power micro solenoid valve, the generator creates
vacuum for use. As soon as the preset maximum value is reached, the digital vacuum
switch acts on the electric coil of the micro solenoid valve and stops the air supply,
reactivating it when the vacuum falls below the minimum level.
Besides maintaining the level of vacuum within set safety values (hysteresis), this
modulation allows for considerable compressed air savings.
A second signal from the vacuum switch (also adjustable and independent with respect
to the first) can be used to start the cycle when the level of vacuum reached is suitable
for use. Once the work cycle is completed, the micro solenoid valve that supplies air
to the generator is deactivated while, at the same time, the ejection solenoid valve is
activated for quick restoration of the atmospheric pressure upon use.
The multi-function MVG vacuum generators can be installed in any position and are
suitable for suction gripping systems, handling metal sheets, glass, marble, ceramics,
plastic, cardboard, wood, etc. and, in particular, for the industrial robotics sector, where
equipment with excellent performance but with limited weight and bulk are increasingly
required.

8.61
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MVG 3 and MVG 7
3D drawings are available on vuototecnica.net

Screw-type
flow regulator
Blow off

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item MVG 3 MVG 7
Intake air flow rate m /h
3
2.8 3.0 3.2 5.6 6.0 6.6
Maximum level of vacuum -KPa 50 70 85 50 70 85
Final pressure mbar abs. 500 300 150 500 300 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 0.5 0.6 0.8 0.8 1.0 1.3
Max quantity of air blown at 5 bar l/min 205 205
Supply solenoid valve position NO/NC NO NO
8
Ejection solenoid valve position NC NC NC
Supply voltage V 24 DC 24 DC
Electrical absorption W 1x2 1x2
Vacuum switch output PNP PNP
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 66 70
Weight Kg 0.666 0.670
G Ø G1/4” G3/8”
Note: To order a generator with NC supply solenoid valve, indicate item code MVG .. NC.
Without digital vacuum switch, indicate code MVG .. SV.
Without ejection solenoid valve, indicate code MVG .. SC.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.62
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MVG 3 and MVG 7

MVG3 portata
MVG7 portata
Air flow rate (Nl/s) at different level of vacuum (-KPa) at optimal supply pressure
MVG 3 MVG 7
MVG 3 MVG 7

3D drawings are available on vuototecnica.net

1 2

MVG3
0,9 portata 1,8
MVG7 portata
0,8 1,6

0,7
MVG 3 1,4 MVG 7
1
0,6 2
1,2

Nl/s
Nl/s

0,9
0,5 1,81

0,8
0,4 1,6
0,8

0,7
0,3 1,4
0,6

0,6
0,2 1,2
0,4
Nl/s

Nl/s
0,5
0,1 1
0,2

0,4
0 0,80
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0,3 -Kpa 0,6 -Kpa

0,2 0,4
MVG7 temp
MVG3 temp Air flow rate (Nl/s)0,2at different levels of vacuums (-KPa) Max vacuum
Generator
0,1
Supp. press. Air consumption
at optimal supply pressure
item 0 bar Nl/s 0
0 10 20 30 40 50 60 70 80 0 10 20 30 0 4010 2050 30 60
40 50 70 60 80
70 80 -KPa
-Kpa -Kpa
MVG 3 5.0 0.8 0.89 0.69 0.41 0.23 0.18 0.12 0.10 0.07 0.03 85
MVG 3 MVG 70.11
MVG 7 5.0 1.3 1.83 1.44 1.11 0.63
MVG7 0.41
temp 0.25 0.16 0.05 85
MVG3 temp
12000 6000

10000 5000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
MVG 3 MVG 7
8000
12000
MVG 3 4000
6000
MVG 7
ms/l
ms/l

6000 3000
10000 5000

4000 2000
8000 4000

2000 1000
ms/l
ms/l

6000 3000

0 0
4000 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
2000
-Kpa -Kpa

2000 1000

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
MVG 3 5.0 0.8 119 274 552 1088 1845 2694 4499 8009 11373 85
MVG 7 5.0 1.3 58 133 268 529 897 1310 2188 3895 5531 85
8
ACCESSORIES AND SPARE PARTS UPON REQUEST
Item MVG 3 MVG 7
Sealing kit and reed valves item 00 KIT MVG 3 00 KIT MVG 7
Exhaust silencer item 00 15 150
Electrical connection cable with axial connector, for vacuum switch item 00 12 20
Electrical connection cable with radial connector, for vacuum switch item 00 12 21
Set of electrical connection cables, with built-in
NO energy saving device and connectors item 00 15 202
Set of electrical connection cables, with built-in
NC energy saving device and connectors item 00 15 203
Digital vacuum switch item 12 10 10
NO supply solenoid valve item 00 15 436
NC supply solenoid valve item 00 15 437

8.63
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MVG 10 and MVG 14
3D drawings are available on vuototecnica.net

Screw-type
flow regulator
Blow off

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item MVG 10 MVG 14
Intake air flow rate m /h
3
7.7 8.4 9.2 10.2 11.2 12.2
Maximum level of vacuum -KPa 50 70 85 50 70 85
Final pressure mbar abs. 500 300 150 500 300 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 0.9 1.3 1.7 1.3 1.7 2.1
Max quantity of air blown at 5 bar l/min 205 205
Supply solenoid valve position NO/NC NO NO
8
Ejection solenoid valve position NC NC NC
Supply voltage V 24 DC 24 DC
Electrical absorption W 1x2 1x2
Vacuum switch output PNP PNP
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 62 70
Weight Kg 0.716 0.720
G Ø G3/8” G3/8”
Note: To order a generator with NC supply solenoid valve, indicate item code MVG .. NC.
Without digital vacuum switch, indicate code MVG .. SV.
Without ejection solenoid valve, indicate code MVG .. SC.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.64
MULTI-STAGE AND MULTI-FUNCTION VACUUM GENERATORS MVG 10 and MVG 14

MVG10 portata
Air flow rate (Nl/s) at different level of vacuum (-KPa)
MVG14 at optimal supply pressure
portata

MVG 10 MVG 14
MVG 10 MVG 14

3D drawings are available on vuototecnica.net

3 4

MVG10 portata
3,5
2,5 MVG14 portata

MVG 10 3 MVG 14
2
3 2,5
4
Nl/s

1,5

Nl/s
2
3,5
2,5
1,5
3
1
2
1
2,5
0,5
0,5
Nl/s

1,5

Nl/s
2

0 0
1,5
1 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
1
0,5
MVG10 temp
Air flow rate (Nl/s)0,5at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal
MVG14 tempsupply pressure
item 0 bar Nl/s 0
0 10 20 30 40 50 60 70 80 0 10 20 30 0 4010 2050 30 60
40 50 70 60 80
70 80 -KPa
-Kpa -Kpa
MVG 10 5.0 1.7 2.55 1.85 1.30 0.75 0.64 0.48 0.30
MVG 140.20 0.09 85
MVG 14 5.0
MVG 10 2.1 3.40 2.45 1.84 1.05 0.88 0.61 0.36 0.24 0.11 85
MVG10 temp

4500 3500 temp

MVG14

4000
3000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
3500
MVG 10 2500
MVG 14
3000
4500
MVG 10 3500
MVG 14
2500 2000
ms/l

ms/l

4000
2000 3000
1500
3500
1500 2500
3000 1000
1000
2500 2000
500
500
ms/l

ms/l

2000 1500
0 0
1500 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa 1000 -Kpa
1000
500
500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
MVG 10 5.0 1.7 41 95 192 379 642 938 1567 2790 3962 85
MVG 14 5.0 2.1 31 71 144 284 482 704 1175 2092 2971 85
8
ACCESSORIES AND SPARE PARTS UPON REQUEST
Item MVG 10 MVG 14
Sealing kit and reed valves item 00 KIT MVG 10 00 KIT MVG 14
Exhaust silencer item N°2 00 15 150
Electrical connection cable with axial connector, for vacuum switch item 00 12 20
Electrical connection cable with radial connector, for vacuum switch item 00 12 21
Set of electrical connection cables, with built-in
NO energy saving device and connectors item 00 15 202
Set of electrical connection cables, with built-in
NC energy saving device and connectors item 00 15 203
Digital vacuum switch item 12 10 10
NO supply solenoid valve item 00 15 436
NC supply solenoid valve item 00 15 437

8.65
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND MULTI-FUNCTION VACUUM
GENERATORS, SERIES MVG

Connector for blowing solenoid valve

Blowing
3D drawings are available on vuototecnica.net

Red Suction valve Blue

valve
Connector for suction solenoid valve

Connector for
vacuum switch

Digital
vacuum switch

Distributor with built-in

ENERGY SAVING device
WHITE
BROWN
GREY
BLACK
BLUE

Cable set with built-in energy saving device

WHITE
DIGITAL OUTPUT (+24) DIGITAL VACUUM SWITCH
PNP ITEM 121010
BROWN
POSITIVE POLE +24

GREY CONNECTION SUPPLY SOLENOID VALVE

NEGATIVE POLE - 0 V
DISTRIBUTOR NO
BLACK
SUCTION ON +24V
8
BLUE BLOWING SOLENOID VALVE
BLOWING ON +24V NC

Item Description
00 15 202 Set of cables with built-in energy saving device for connection to:
- Digital vacuum switch
- NO micro supply solenoid valve
- NC micro ejection solenoid valve
Cable length - 5 m

8.66
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND
MULTI-FUNCTION VACUUM GENERATORS, SERIES MVG

Cable set with built-in energy saving device

WHITE
DIGITAL OUTPUT (+24) DIGITAL VACUUM SWITCH
PNP ITEM 121010
BROWN
POSITIVE POLE +24

GREY CONNECTION SUPPLY SOLENOID VALVE

NEGATIVE POLE - 0 V
DISTRIBUTOR NC
BLACK
SUCTION ON +24V
BLUE BLOWING SOLENOID VALVE
BLOWING ON +24V NC

Connector

Item Description
00 15 157 Connector with LED for micro solenoid valves

Cable with axial connector

Item Description
00 12 20 Electrical connection cable with M8 - 4 pin axial connector 8
for digital vacuum switch length 5 m

Cable with radial connector

Item Description
00 12 21 Electrical connection cable with M8 - 4 pin radial connector
for digital vacuum switch length 5 m

8.67
ACCESSORIES AND SPARE PARTS FOR MULTI-STAGE AND
MULTI-FUNCTION VACUUM GENERATORS, SERIES MVG
3D drawings are available on vuototecnica.net

NO micro supply solenoid valve

Interface

Item Description

00 15 436 NO micro solenoid valves with built-in low absorption electrical coil and interface

Micro solenoid
valve
Manual drive

NC supply and blowing micro solenoid valve Interface

Item Description

00 15 437 NC micro solenoid valves with built-in low absorption electrical coil and interface

Micro solenoid
valve
Manual drive

Replacement plate for micro blowing solenoid valve

Item Description
00 15 178 Replacement plate for micro blowing solenoid valve

Digital vacuum switch

Item Description
12 10 10 Digital vacuum switch

8.68
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS, SERIES
GVMM - GENERAL DESCRIPTION
Modular multi-function vacuum generators are true independent vacuum units that offer
an entire vacuum control system.
They feature a reduced thickness and weight compared to their suction flow rate and
they have been designed to be assembled with screws to one or more intermediate

3D drawings are available on vuototecnica.net

modules MI. The original internal connection system for the compressed air supply
allows communication with no need for external manifolds.
This modular system allows increasing the number of independent vacuum units
according to the requirements. In fact, you can order a multi-function vacuum generator
and the intermediate modules with the desired capacities, already assembled, or you can
assemble one or more intermediate modules to the GVMM generator that has already
been installed on the machine, without having to make particular modifications. GVMM
vacuum generators are composed of an anodised aluminium mono-block with lid, inside
of which the silenced multiple ejectors are installed and the vacuum chamber and the
compressed air supply connection are contained.
The following are instead installed on the outside:
- A micro solenoid valve for supplying compressed air to the generator.
- A micro solenoid valve for blowing the exhaust compressed air.
- An adjustable flow regulator for dosing the exhaust air.
- A digital vacuum switch provided with display and commutation LEDs, for managing the
compressed air supply and for signalling the safety cycle start-up.
- An anodised aluminium or transparent Plexiglass manifold provided with vacuum
connections with built-in suction filter, easy to inspect, and a check valve for maintaining
the vacuum in case of electricity or compressed air failure.
By activating the compressed air power micro solenoid valve, the generator creates
vacuum for use. As soon as the preset maximum value is reached, the digital vacuum
switch acts on the electric coil of the micro solenoid valve and stops the air supply,
reactivating it when the vacuum falls below the minimum level.
Besides maintaining the level of vacuum within set safety values (hysteresis), this
modulation allows for considerable compressed air savings.
A second signal from the vacuum switch (also adjustable and independent with respect
to the first) can be used to start the cycle when the level of vacuum reached is suitable
for use. Once the work cycle is completed, the micro solenoid valve that supplies air
to the generator is deactivated while, at the same time, the ejection solenoid valve is
activated for quick restoration of the atmospheric pressure upon use.
GVMM multi-function vacuum generators can be installed in any position and are suited
for interconnecting vacuum gripping systems for handling sheet steel, glass, marble,
ceramic, plastic, cardboard, wood, etc., and, in particular, for the industrial robotics sector
which requires equipment with excellent performance and several independent vacuum
units for controlling several applications but with reduced size and weight.

8.69
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS,
GVMM 3 and GVMM 7
3D drawings are available on vuototecnica.net

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item GVMM 3 GVMM 7
Intake air flow rate m3/h 2.6 2.8 3.0 5.5 6.0 6.4
Maximum level of vacuum -KPa 64 85 85 60 80 85
Final pressure mbar abs. 360 150 150 400 200 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 0.6 0.7 0.8 0.9 1.1 1.3
Max quantity of air blown at 5 bar l/min 128 128
Supply solenoid valve position NO/NC NO NO
Electrical absorption W 2 2
8
Ejection solenoid valve position NC NC NC
Electrical absorption W 4 4
Supply voltage V 24DC 24DC
Vacuum switch output PNP PNP
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 66 70
Weight g 420 420
G Ø G1/4” G1/4”
Note: To order a generator without a digital vacuum switch, indicate code GVMM .. SV.
To order a generator with NC supply solenoid valve, indicate code GVMM .. NC.
To order a generator with aluminium manifold, indicate code GVMM .. AL.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.70
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS,
GVMM 3 and GVMM 7

GVMM3 portata Air flow rate (Nl/s) at different level of vacuum GVMM7
(-KPa) portata
at optimal supply pressure
GVMM 3 GVMM 7
GVMM 3 GVMM 7

3D drawings are available on vuototecnica.net

0,9 2

0,8 1,8
GVMM7 portata
GVMM3 portata
1,6
0,7
GVMM 3 GVMM 7
1,4
0,6
0,9 2
1,2
0,5

Nl/s
Nl/s

0,8 1,8
1
0,4
1,6
0,8
0,7
0,3
1,4
0,6
0,6
0,2 1,2
0,4
0,5
0,1

Nl/s
Nl/s

1
0,2
0,4
0 0,8
0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0,3
-Kpa 0,6 -Kpa
0,2
0,4
GVMM3 temp
0,1 Air flow rate (Nl/s)0,2at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal
GVMM7 supply pressure
tempi
item 0 bar Nl/s 0
0 10 20 30 40 50 60 70 80 0 10 20 30 0 4010 2050 30 60
40 50 70 60 80
70 80 -KPa
-Kpa -Kpa
GVMM 3 5.0
GVMM 30.8 0.83 0.66 0.38 0.20 0.16 0.11 GVMM 0.06
0.09 7 0.02 85
GVMM
GVMM37 temp 5.0 1.3 1.78 1.30 0.98 0.56 0.44 0.29 0.20 0.14 0.06 85
14000 6000
GVMM7 tempi

12000
5000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
GVMM 3 GVMM 7
10000

14000
GVMM 3 4000
6000
GVMM 7
8000
ms/l
ms/l

3000
12000
6000 5000

10000 2000
4000 4000

8000 1000
2000
ms/l
ms/l

3000
6000
0 0
10 20 30 40 50 60 70 80 85 2000 10 20 30 40 50 60 70 80 85
4000 -Kpa -Kpa

1000
2000

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
GVMM 3 5.0 0.8 128 294 592 1167 1978 2889 4824 8588 12195 85
GVMM 7 5.0 1.3 59 137 275 543 921 1344 2245 3997 5676 85
8
ACCESSORIES AND SPARE PARTS UPON REQUEST
Item GVMM 3 GVMM 7
Sealing kit and reed valves item 00 KIT GVMM 3 00 KIT GVMM 7
Exhaust silencer item 00 15 150
Electrical connection cable with axial connector, for vacuum switch item 00 12 20
Electrical connection cable with radial connector, for vacuum switch item 00 12 21
Set of electrical connection cables, with built-in
NO energy saving device and connectors item 00 15 202
Set of electrical connection cables, with built-in
NC energy saving device and connectors item 00 15 203
Digital vacuum switch item 12 10 10
NO supply solenoid valve item 00 15 176
NC supply solenoid valve item 00 15 175

8.71
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS,
GVMM 10 and GVMM 14
3D drawings are available on vuototecnica.net

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item GVMM 10 GVMM 14
Intake air flow rate m3/h 7.5 8.3 9.1 10.1 11.1 12.1
Maximum level of vacuum -KPa 60 80 85 60 80 85
Final pressure mbar abs. 400 200 150 400 200 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 1.1 1.4 1.7 1.4 1.7 2.1
Max quantity of air blown at 5 bar l/min 128 128
Supply solenoid valve position NO/NC NO NO
Electrical absorption W 2 2
8
Ejection solenoid valve position NC NC NC
Electrical absorption W 4 4
Supply voltage V 24DC 24DC
Vacuum switch output PNP PNP
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 70 72
Weight g 460 460
G Ø G1/4” G1/4”
Note: To order a generator without a digital vacuum switch, indicate code GVMM .. SV.
To order a generator with NC supply solenoid valve, indicate code GVMM .. NC.
To order a generator with aluminium manifold, indicate code GVMM .. AL.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.72
MULTI-STAGE, MULTI-FUNCTION AND MODULAR VACUUM GENERATORS,
GVMM 10 and GVMM 14
GVMM10 portata
GVMM14 portata
GVMM
Air flow rate 10 at different level of vacuum (-KPa) at optimal supply pressure
(Nl/s)

GVMM 10 GVMM 14

3D drawings are available on vuototecnica.net

3 4

GVMM10 portata 3,5

GVMM14 portata
2,5
GVMM 10 GVMM 14
3

2
3 2,5
4
Nl/s

Nl/s
1,5 2
3,5
2,5
1,5
3
1
2
1
2,5
0,5
0,5
Nl/s

Nl/s
1,5 2

0 0
1,5
1 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
1

0,5 GVMM14 tempi

GVMM10 tempi Air flow rate (Nl/s)0,5at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item 0 bar Nl/s 0
0 10 20 30 40 50 60 70 80 0 10 20 30 0 4010 2050 30 60
40 50 70 60 80
70 80 -KPa
GVMM 10 5.0 GVMM
-Kpa
101.7 2.52 2.00 1.66 0.97 0.56 0.40
-Kpa
0.22 0.16 0.07 85
GVMM 14 5.0 2.1 3.35 2.42 1.84 0.99
GVMM140.80 0.58
tempi 0.34 0.22 0.10 85
GVMM10 tempi
4500 3500

4000
3000

3500
GVMM
Evacuation rates (ms/l10
=s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
GVMM 14
2500
3000
4500
GVMM 10 3500
GVMM 14
2500 2000
ms/l

ms/l

4000
3000
2000 1500
3500
1500 2500
3000 1000
1000
2500 2000
500
ms/l
ms/l

500
2000 1500
0 0
1500 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa 1000 -Kpa
1000
500
500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
GVMM 10 5.0 1.7 42 97 195 384 651 951 1589 2828 4016 85
GVMM 14 5.0 2.1 31 72 146 288 489 714 1193 2124 3016 85
8
ACCESSORIES AND SPARE PARTS UPON REQUEST
Item GVMM 10 GVMM 14
Sealing kit and reed valves item 00 KIT GVMM 10 00 KIT GVMM 14
Exhaust silencer item N°2 00 15 150
Electrical connection cable with axial connector, for vacuum switch item 00 12 20
Electrical connection cable with radial connector, for vacuum switch item 00 12 21
Set of electrical connection cables, with built-in
NO energy saving device and connectors item 00 15 202
Set of electrical connection cables, with built-in
NC energy saving device and connectors item 00 15 203
Digital vacuum switch item 12 10 10
NO supply solenoid valve item 00 15 176
NC supply solenoid valve item 00 15 175

8.73
MULTI-STAGE, MULTI-FUNCTION AND MODULAR INTERMEDIATE VACUUM MODULES
SERIES MI - GENERAL DESCRIPTION
Intermediate modules are non-independent multi-stage and multi-
function vacuum generators to be assembled to the generators of the
GVMM range.
Their thickness and weight are reduced to the maximum compared
3D drawings are available on vuototecnica.net

to their suction flow rate and they have been designed to be enclosed
between the lid and the base of the GVMM vacuum generator and
fixed with screws. The internal connections for the compressed air
supply allow communication between them and the basic generator,
with no need for external manifolds.
This way, each module becomes an independent vacuum unit that can
control an entire vacuum system.
They can be ordered in the desired amount and flow rate, either
already assembled onto the GVMM multi-function vacuum generator,
or separately, to be assembled to the GVMM generator previously
installed onto the machine. In this case, we suggest ordering a screw
kit suitable for the number of modules to be assembled.
MI intermediate vacuum modules are made up of the same elements
that compose GVMM generators, except for the lid. They operate and
they are used as the GVMM multi-function vacuum generator onto
which they are assembled.

8.74
INTERMEDIATE VACUUM MODULES MI 3 and MI 7

3D drawings are available on vuototecnica.net

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION
Item MI 3 MI 7
Intake air flow rate m3/h 2.6 2.8 3.0 5.5 6.0 6.4
Maximum level of vacuum -KPa 64 85 85 60 80 85
Final pressure mbar abs. 360 150 150 400 200 150
Supply pressure bar 3 4 5 3 4 5
Optimal supply pressure bar 5 5
Air consumption Nl/s 0.6 0.7 0.8 0.9 1.1 1.3
Max quantity of air blown at 5 bar l/min 128 128
Supply solenoid valve position NO/NC NO NO
Electrical absorption W 2 2
8
Ejection solenoid valve position NC NC NC
Electrical absorption W 4 4
Supply voltage V 24DC 24DC
Vacuum switch output PNP PNP
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 66 70
Weight g 380 380
G Ø G1/4” G1/4”
Note: To order a generator without a digital vacuum switch, indicate code MI .. SV.
To order a generator with NC supply solenoid valve, indicate code MI .. NC.
To order a generator with aluminium manifold, indicate code MI .. AL.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.75
INTERMEDIATE VACUUM MODULES MI 3 and MI 7

MI3 portata Air flow rate (Nl/s) at different level of vacuum

MI7(-KPa) at optimal supply pressure
portata

MI 3 MI 7
MI 3 MI 7
3D drawings are available on vuototecnica.net

0,9 2

0,8 1,8
MI3 portata MI7 portata
1,6
0,7
MI 3 MI 7
1,4
0,6
0,9 2
1,2
0,5
1,8

Nl/s
1
Nl/s

0,8
0,4
1,6
0,8
0,7
0,3
1,4
0,6
0,6
0,2 1,2
0,4
0,5

Nl/s
1
Nl/s

0,1 0,2
0,4
0 0,8
0
0,3 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa 0,6 -Kpa
0,2 0,4
MI3 temp MI7 temp
0,1 Air flow rate (Nl/s)0,2at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item 0 bar Nl/s 0
0 10 20 30 40 50 60 70 80 0 10 20 30 0 4010 2050 30 60
40 50 70 60 80
70 80 -KPa
-Kpa -Kpa
MI 3 5.0 0.8 0.83 0.66 0.38 0.20 0.16 0.11 0.09
MI 7 0.06 0.02 85
MI 3
MI 7
MI3 temp 5.0 1.3 1.78 1.30 0.98 MI7 0.56 0.44
temp 0.29 0.20 0.14 0.06 85
14000 6000

12000
5000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
MI 3 MI 7
10000

14000
MI 3 4000
6000
MI 7
8000
ms/l
ms/l

3000
12000
6000 5000

10000 2000
4000 4000

8000 1000
2000
ms/l
ms/l

3000
6000
0 0
10 20 30 40 50 60 70 80 85 2000 10 20 30 40 50 60 70 80 85
4000 -Kpa -Kpa

1000
2000

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
MI 3 5.0 0.8 128 294 592 1167 1978 2889 4824 8588 12195 85
MI 7 5.0 1.3 59 137 275 543 921 1344 2245 3997 5676 85
8
ACCESSORIES AND SPARE PARTS UPON REQUEST
Item MI 3 MI 7
Sealing kit and reed valves item 00 KIT MI 3 00 KIT MI 7
Exhaust silencer item 00 15 150
Electrical connection cable with axial connector, for vacuum switch item 00 12 20
Electrical connection cable with radial connector, for vacuum switch item 00 12 21
Set of electrical connection cables, with built-in
NO energy saving device and connectors item 00 15 202
Set of electrical connection cables, with built-in
NC energy saving device and connectors item 00 15 203
Digital vacuum switch item 12 10 10
NO supply solenoid valve item 00 15 176
NC supply solenoid valve item 00 15 175

8.76
INTERMEDIATE VACUUM MODULES MI 10 and MI 14

3D drawings are available on vuototecnica.net

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION
Item MI 10 MI 14
Intake air flow rate m3/h 7.5 8.3 9.1 10.1 11.1 12.1
Maximum level of vacuum -KPa 60 80 85 60 80 85
Final pressure mbar abs. 400 200 150 400 200 150
Optimal final pressure mbar abs. 150 150
Supply pressure bar 3 4 5 3 4 5
Air consumption Nl/s 1.1 1.4 1.7 1.4 1.7 2.1
Max quantity of air blown at 5 bar l/min 128 128
Supply solenoid valve position NO/NC NO NO
Electrical absorption W 2 2
8
Ejection solenoid valve position NC NC NC
Electrical absorption W 4 4
Supply voltage V 24DC 24DC
Vacuum switch output PNP PNP
Degree of protection IP 65 65
Temperature of use °C -10 / +60 -10 / +60
Noise level at
optimal supply pressure dB(A) 70 72
Weight g 410 410
G Ø G1/4” G1/4”
Note: To order a generator without a digital vacuum switch, indicate code MI .. SV.
To order a generator with NC supply solenoid valve, indicate code MI .. NC.
To order a generator with aluminium manifold, indicate code MI .. AL.
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.77
INTERMEDIATE VACUUM MODULES MI 10 and MI 14

MI10 portata Air flow rate (Nl/s) at different level of vacuumMI14

(-KPa)portata
at optimal supply pressure
MI 10
MI 10 MI 14
3D drawings are available on vuototecnica.net

3 4

3,5
MI10
2,5 portata MI14 portata
MI 10 3 MI 14
2
3 2,5
44
Nl/s

1,5 2
3,5
3,5

Nl/s
2,5
1,5
3
1
2
1
2,5
2,5
0,5
0,5

Nl/s
Nl/s

1,5 2

Nl/s
0 0
1,5
1,5
1 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa -Kpa
1

MI100,5 temp
Air flow rate (Nl/s)
MI140,5at different
0,5
temp levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item 0 bar Nl/s 0
0 10 20 30 40 50 60 70 80 0 10 20 30 00 401010 50
20
20 30
30 60
40
40 50
50 70 60
60 80
70
70 80
80 -KPa
-Kpa -Kpa
-Kpa
MI 10 5.0 MI 10 1.7 2.52 2.00 1.66 0.97 0.56 0.40 0.22 0.16 0.07 85
MI 14
MI10 temp 5.0 2.1 3.35 2.42 1.84 0.99 0.80 0.58 0.34 0.22 0.10 85
MI14 temp
4500 3500

4000
3000
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
3500 MI 10 MI 14
2500
3000
4500
MI 10 3500
MI 14
2500 2000
ms/l

4000
ms/l

3000
2000 1500
3500
1500 2500
3000 1000
1000
2000
2500 500
ms/l

500
ms/l

2000 1500
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
1500
-Kpa 1000 -Kpa
1000
500
500

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
-Kpa -Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
MI 10 5.0 1.7 42 97 195 384 651 951 1589 2828 4016 85
MI 14 5.0 2.1 31 72 146 288 489 714 1193 2124 3016 85
8
ACCESSORIES AND SPARE PARTS UPON REQUEST
Item MI 10 MI 14
Sealing kit and reed valves item 00 KIT MI 10 00 KIT MI 14
Exhaust silencer item N°2 00 15 150
Electrical connection cable with axial connector, for vacuum switch item 00 12 20
Electrical connection cable with radial connector, for vacuum switch item 00 12 21
Set of electrical connection cables, with built-in
NO energy saving device and connectors item 00 15 202
Set of electrical connection cables, with built-in
NC energy saving device and connectors item 00 15 203
Digital vacuum switch item 12 10 10
NO supply solenoid valve item 00 15 176
NC supply solenoid valve item 00 15 175

8.78
ACCESSORIES AND SPARE PARTS FOR VACUUM GENERATORS AND MODULES SERIES
GVMM and MI

Distributor with built-in

ENERGY SAVING device

3D drawings are available on vuototecnica.net

WHITE
BROWN
GREY
Connector for blowing solenoid valve
BLACK
BLUE

Red Blue

Suction
Blowing
valve
valve

Connector for suction solenoid valve

Connector for
vacuum switch

Digital
vacuum
switch

Manifold

Cable set with built-in energy saving device

WHITE
DIGITAL OUTPUT (+24) DIGITAL VACUUM SWITCH PNP
ITEM 121010
BROWN
POSITIVE POLE +24
GREY CONNECTION SUPPLY SOLENOID VALVE
NEGATIVE POLE - 0 V
DISTRIBUTOR NO
BLACK 8
SUCTION ON +24V
BLUE BLOWING SOLENOID VALVE
BLOWING ON +24V NC

8.79
ACCESSORIES AND SPARE PARTS FOR VACUUM GENERATORS AND MODULES SERIES
GVMM and MI

Cable set with built-in energy saving device

WHITE
DIGITAL OUTPUT (+24) DIGITAL VACUUM SWITCH PNP
ITEM 121010
POSITIVE POLE +24 BROWN

GREY CONNECTION SUPPLY SOLENOID VALVE

NEGATIVE POLE - 0 V
DISTRIBUTOR NC
BLACK
SUCTION ON +24V
BLUE BLOWING SOLENOID VALVE
BLOWING ON +24V NC

Connector

Item Description
00 15 157 Connector with LED for micro solenoid valves

Cable with axial connector

Item Description
00 12 20 Electrical connection cable with M8 - 4 pin axial connector
for digital vacuum switches length 5 m

Cable with radial connector

8 Item Description
00 12 21 Electrical connection cable with M8 - 4 pin radial connector
for digital vacuum switches length 5 m

Digital vacuum switch

Item Description
12 10 10 Digital vacuum switch

8.80
ACCESSORIES AND SPARE PARTS FOR VACUUM GENERATORS AND MODULES SERIES
GVMM and MI

NO micro supply solenoid valve

Item Description
00 15 176 NO micro supply solenoid valve - h = 43 mm

NC supply and blowing micro solenoid valve

Item Description
00 15 175 NC supply and blowing micro solenoid valve - h = 37.5 mm

Plexiglass manifolds

Item Description
00 15 171 Plexiglass suction manifold for GVMM - MI 3/7
00 15 188 Plexiglass suction manifold for GVMM - MI 10/14

Aluminium manifolds

Item Description
00 15 174 Aluminium suction manifold for GVMM - MI 3/7
00 15 187 Aluminium suction manifold for GVMM - MI 10/14

Support

Item Description
00 15 306 L-shaped fixing support in galvanised steel sheet

8.81
MODULAR VACUUM SYSTEMS SET-UP

GVMM multi-function vacuum generators can be assembled with

one or more intermediate modules, thus forming a modular vacuum
system, featuring a compact shape and reduced size and weight.
As a standard, up to 6 vacuum units can be assembled, but using
3D drawings are available on vuototecnica.net

threaded bars instead allows assembling even more.

EXAMPLE OF SET-UP 1
No. Item B
1 GVMM 3 - 7 20
2 MI 10 - 14 25
3 MI 3 - 7 20
Total length L= 65
Required screw kit: Item 00 KIT GVMM 02

Ordering example:
1 Generator GVMM 3
1 Intermediate module MI 10
1 Intermediate module MI 3
1 kit of stainless steel screws 00 KIT GVMM 02

EXAMPLE OF SET-UP 2 00 KIT GVMM 02

No. Item B
1 GVMM 10 - 14 25
2 MI 3 - 7 20
3 MI 10 - 14 25
Total length L= 70
Required screw kit: Item 00 KIT GVMM 03

Ordering example:
1 Generator GVMM 10
1 Intermediate module MI 3
1 Intermediate module MI 10
1 kit of stainless steel screws 00 KIT GVMM 03

STAINLESS STEEL M5 SCREW KIT

8
Item L
00 KIT GVMM 01 45 - 50
00 KIT GVMM 02 60 - 65
00 KIT GVMM 03 70 - 75
00 KIT GVMM 04 80 - 85
00 KIT GVMM 05 90 - 95
00 KIT GVMM 06 100 - 105
00 KIT GVMM 07 110 - 115
00 KIT GVMM 08 120 - 125
00 KIT GVMM 09 130 - 135
00 KIT GVMM 12 140 - 145
00 KIT GVMM 11 150 - 155

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
8.82
MULTI-STAGE VACUUM GENERATORS PVP 12 MX / MXLP and 25 MX / MXLP

This range of multiple ejector vacuum generators offers increased

suction flow rate, given the same compressed air consumption, than
single-stage models.
Supply pressure goes between 4-6 bar, for items MX and between 1-3 bar,

3D drawings are available on vuototecnica.net

for MXLP. The capacities go from 10.5 to 31 m3/h. They are fully made
with anodised aluminium, with stainless steel ejectors and screws. The
EPDM seals, the silicone reed valves and the vacuum gauge are provided
as standard. They are equipped with additional intake connections for
increased points of usage or control tools. The suctioned air discharge
connections are threaded to allow for installation, upon request, of
“free-flow” SSX high sound damping silencers

2 Ø 6.5 holes

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION U 1-2-3=ADDITIONAL VACUUM CONNECTION

Item PVP 12 MX PVP 12 MXLP
Intake air flow rate m /h3
16.0 18.0 21.0 10.5 15.5 18.0
Maximum level of vacuum -KPa 65 85 90 30 61 86
8
Final pressure abs. mbar 350 150 100 700 390 140
Supply pressure bar 4 5 6 1 2 3
Optimal supply pressure bar 6 3
Air consumption Nl/s 1.0 1.3 1.5 1.1 1.6 2.3
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 65 79
Weight g 660 660

Spare parts PVP 12 MX / MXLP

Sealing kit and reed valves item 00 KIT PVP 12 MX
Sound absorption material for exhaust item 00 15 112
Vacuum gauge item 09 03 15
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.83
MULTI-STAGE VACUUM GENERATORS PVP 12 MX / MXLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
portata

PVP 12 MX PVP 12 MXLP

3D drawings are available on vuototecnica.net

PVP 12 MX
PVP12 MXLP 7

Nl/s
portata 3

PVP 12 MX
PVP12 MXLP 27

05
0 10 20 30 40 50 60 70 80
-Kpa
4
Nl/s

3
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. tempAir consumption
at optimal supply pressure
item bar PVP 12 MX Nl/s 2
PVP12 MXLP 8000 0 10 20 30 40 50 60 70 80 -KPa
PVP 12 MX 6.0 1.57000
1 5.80 4.14 2.76 1.38 0.98 0.78 0.59 0.41 0.23 90
PVP 12 MXLP 3.0 2.3 5.00 2.27 1.66 1.05 0.88 0.77 0.64 0.42 0.22 86
6000
0
0 10 20 30 40 50 60 70 80

5000 -Kpa

Evacuation rates (ms/l =s/m

4000 ) at different levels of vacuums (-KPa) at optimal supply pressure
3
ms/l

temp

PVP 12 MX
3000
PVP 12 MX PVP 12 MXLP
PVP12 MXLP 8000
2000

7000
1000

6000
0
10 20 30 40 50 60 70 80 85
5000
-Kpa
ms/l

4000

3000

2000

1000

0
10 20 30 40 50 60 70 80 85
-Kpa

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 12 MX 6.0 1.5 15 38 85 204 365 559 929 1607 5916 90
PVP 12 MXLP 3.0 2.3 22 56 120 240 410 650 975 1950 7160 86
8
ACCESSORIES UPON REQUEST
Silencer item SSX 3/8’’

8.84
MULTI-STAGE VACUUM GENERATORS PVP 25 MX / MXLP

3D drawings are available on vuototecnica.net

2 Ø 6.5 holes

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION U 1-2-3=ADDITIONAL VACUUM CONNECTION

Item PVP 25 MX PVP 25 MXLP
Intake air flow rate m /h3
25.0 28.0 31.0 19.0 27.5 34.0
Maximum level of vacuum -KPa 65 85 90 30 61 86
8
Final pressure abs. mbar 350 150 100 700 390 140
Supply pressure bar 4 5 6 1 2 3
Optimal supply pressure bar 6 3
Air consumption Nl/s 2.1 2.6 3.0 2.2 3.2 4.5
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 70 70
Weight g 960 960

Spare parts PVP 25 MX / MXLP

Sealing kit and reed valves item 00 KIT PVP 25 MX
Sound absorption material for exhaust item 00 15 113
Vacuum gauge item 09 03 15
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.85
MULTI-STAGE VACUUM GENERATORS PVP 25 MX / MXLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
portata

PVP 25 MX PVP 25 MXLP

3D drawings are available on vuototecnica.net

PVP 25 MX
PVP 25 MXLP 10

Nl/s
5

portata 4

PVP 25 MX 3
PVP 25 MXLP 10

2
9

1
8

0
7
0 10 20 30 40 50 60 70 80
6 PVP 25 MX -Kpa
PVP 25 MXLP
Nl/s

5
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
temp 4
at optimal supply pressure
item bar PVP 25 MX
Nl/s 3
6000
PVP 25 MXLP
0 10 20 30 40 50 60 70 80 -KPa
2
PVP 25 MX 6.0 3.05000 8.61 6.15 4.10 2.05 1.46 1.17 0.88 0.61 0.35 90
1
PVP 25 MXLP 3.0 4.5 9.44 3.77 2.77 1.72 1.58 1.36 1.11 0.72 0.37 86
0
4000 0 10 20 30 40 50 60 70 80
PVP 25 MX -Kpa
PVP 25 MXLP
Evacuation rates (ms/l =s/m
3000 ) at different levels of vacuums (-KPa) at optimal supply pressure
ms/l

temp

PVP 25 MX 2000 PVP 25 MX PVP 25 MXLP

PVP 25 MXLP 6000

1000
5000

0
4000 10 20 30 40 50 60 70 80 85
PVP 25 MX -Kpa
PVP 25 MXLP
ms/l

3000

2000

1000

0
10 20 30 40 50 60 70 80 85
PVP 25 MX -Kpa
PVP 25 MXLP

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 25 MX 6.0 3.0 10 26 57 137 246 377 626 1083 3986 90
PVP 25 MXLP 3.0 4.5 16 41 83 165 290 460 690 1380 5070 86
8
ACCESSORIES UPON REQUEST
4 silencers item SSX 1/4’’

8.86
MULTI-STAGE VACUUM GENERATORS PVP 40 M / MLP ÷ PVP 300 M / MLP

Created to be assembled on OCTOPUS gripping systems, this series of generators is available with
suction capacities between 24 and 320 m3/h. The supply pressure goes from 4-6 bar for M items
and from 1-3 bar for MLP items. Level of vacuum and flow rate can be adjusted according to the
supply air pressure. Characterised by their new generation of ejectors, boasting an excellent ratio

3D drawings are available on vuototecnica.net

between the quantity of air consumed and that suctioned, benefiting operational consumption.
The silencers are built into all generators. They are fully made with anodised aluminium, with
stainless steel ejectors and screws. EPDM or VITON seals and reed valves upon request. Low
maintenance and simple scheduled filter cleaning.

Vacuum
gauge

Pressure
gauge

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 40 M PVP 70 M PVP 100 M
Intake air flow rate m /h
3
36 39 42 65 73 80 88 98 108
Maximum level of vacuum -KPa 65 82 90 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6 4 5 6
Optimal supply pressure bar 6 6 6
Air consumption Nl/s 2.3 2.7 3.2 4.9 5.7 6.6 7.2 8.5 9.8
Temperature of use °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 67 68 70
Weight Kg 4.2 4.2 4.2

Item PVP 40 MLP PVP 70 MLP PVP 100 MLP

Intake air flow rate m3/h 24 35 41 41 56 73 50 80 95
Maximum level of vacuum -KPa 30 64 88 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120 700 360 120
Supply pressure bar 1 2 3 1 2 3 1 2 3
Optimal supply pressure bar
8
3 3 3
Air consumption Nl/s 2.4 3.4 4.4 4.6 7.0 8.9 6.7 10.2 13.3
Temperature of use °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 70 72 75
Weight Kg 4.2 4.2 4.2

Spare parts PVP 40 M / MLP PVP 70 M / MLP PVP 100 M / MLP

Sealing kit and reed valves item 00 KIT PVP 40 M 00 KIT PVP 70 M 00 KIT PVP 100 M
Exhaust silencer item 00 15 110 00 15 110 00 15 110
Silencer on nozzles item 00 15 111 00 15 111 00 15 111
Vacuum gauge item 09 03 15 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25 09 03 25
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.87
MULTI-STAGE VACUUM GENERATORS PVP 40 M / MLP,
PVP 70 M / MLP and PVP 100 M / MLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
portata
PVP 40 M
PVP 40 MLP
3D drawings are available on vuototecnica.net

portata

PVP 40 MLP PVP 70 MLP

portata
PVP 40 M PVP 70 M PVP 1 00 M
PVP 70 M
PVP 70 MLP
25
PVP 100 M
35
PVP 1 00 MLP
14 PVP 100 MLP

12 30
20

10 25

15
8 20

Nl/s
Nl/s
Nl/s

6 15
10

4 10

5
2 5

0 0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 40 M -Kpa PVP 70 M -Kpa PVP 100 M -Kpa
temp PVP 40 MLP PVP 70 MLP PVP 100 MLP
PVP 40 M
PVP 40 MLP
temp
PVP 70 M temp
portata PVP 70 MLP
PVP 40 M 3500 Air flow rate (Nl/s) at different
PVP 100 MLPlevels1800
PVP 100 M
of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
2500
PVP 40 MLP
PVP 70 M portata at optimal supply
portata
pressure
3000 item bar PVP 70Nl/s
MLP
PVP 100 M
1600
25
2000
0 10 20 30 40
PVP 100 MLP 5035 60 70 80 -KPa
14 1400
PVP 40 M
2500
6.0 3.2 11.66 8.32 5.55 2.77 1.98 1.5830 1.19 0.83 0.47 90
1200
PVP 70 M
12
2000
6.0 6.6 20
1500 22.20 15.80 10.50 5.29 3.77 3.02 2.27 1.58 0.90 90
PVP 100 M 6.0 9.8 30.00 21.40 14.20 7.14 5.10 1000
4.0825 3.06 2.14 1.22 90
ms/l

ms/l

ms/l
10
1500 800
15
1000 20
8PVP 40 MLP 3.0 4.4 11.40 5.42 3.45 2.19 2.03 1.72 1.34 0.95 0.54 88
Nl/s
600
Nl/s

1000
Nl/s

PVP 70 MLP 3.0 8.9 10

20.30 9.65 6.15 3.88 3.61 3.0515
400
2.36 1.66 0.94 88
6 500
500PVP 100 MLP 3.0 13.3 26.40 12.50 8.00 5.07 4.70 4.00 3.10 2.20 1.25 88
10
200
4
0 5
0 0
10 20 30 40 50 60 70 80 85 5
2 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
PVP 40 M -Kpa
PVP 40 MLP PVP 70 M -Kpa PVP 100 M -Kpa
0 PVP 70 MLP 0 PVP 100 MLP
0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
0 10 20 30 40 50 60 70 80
PVP 70 M -Kpa PVP 100 M -Kpa
PVP 40 MEvacuation
-Kpa rates (ms/l =s/m3) at different
PVP 70 MLPlevels of vacuums (-KPa) at optimalPVP
supply
100 MLP pressure
temp PVP 40 MLP
PVP 40 M
PVP 40 MLP
temp

PVP 40 M PVP 40 MLP PVP 70 M PVP 70 MLP PVP 1 00 M PVP 1 00 MLP

PVP 70 M temp
PVP 70 MLP
PVP 100 M
3500 2500 PVP 100 MLP 1800

1600
3000
2000
1400
2500
1200
1500
2000 1000
ms/l

ms/l
ms/l

800
1500
1000
600
1000

500 400

500
200

0 0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
8
10 20 30 40 50 60 70 80 85
PVP 40 M -Kpa PVP 70 M -Kpa PVP 100 M -Kpa
PVP 40 MLP PVP 70 MLP PVP 100 MLP

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 40 M 6.0 3.2 7.7 19.2 42.3 101.6 182.0 278.4 462.3 799.8 2943 90
PVP 70 M 6.0 6.6 4.0 10.1 22.2 53.3 95.5 146.1 242.6 419.7 1544 90
PVP 100 M 6.0 9.8 3.0 7.4 16.4 39.5 70.7 108.2 179.6 310.8 1144 90

PVP 40 MLP 3.0 4.4 12.0 28.0 58.0 116.0 158.0 250.0 382.0 764.0 2820 88
PVP 70 MLP 3.0 8.9 9.0 21.0 44.0 88.0 120.0 190.0 290.0 580.0 2150 88
PVP 100 MLP 3.0 13.3 7.0 16.0 34.0 68.0 93.0 147.0 224.0 448.0 1650 88

8.88
MULTI-STAGE VACUUM GENERATORS PVP 140 M / MLP,
PVP 170 M / MLP and PVP 200 M / MLP

3D drawings are available on vuototecnica.net

Vacuum
gauge

Pressure
gauge

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 140 M PVP 170 M PVP 200 M
Intake air flow rate m /h
3
125 140 152 150 168 182 170 188 200
Maximum level of vacuum -KPa 65 82 90 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6 4 5 6
Optimal supply pressure bar 6 6 6
Air consumption Nl/s 9.6 11.4 13.0 12.1 14.2 16.3 14.2 16.9 19.4
Temperature of use °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 70 71 72
Weight Kg 5.1 5.1 5.1

Item PVP 140 MLP PVP 170 MLP PVP 200 MLP
Intake air flow rate m3/h 73 115 138 80 137 165 105 157 190
Maximum level of vacuum -KPa 30 64 88 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120 700 360 120
Supply pressure bar 1 2 3 1 2 3 1 2 3
Optimal supply pressure bar
8
3 3 3
Air consumption Nl/s 8.6 13.3 17.8 10.5 16.3 22.2 12.8 20.0 26.6
Temperature of use °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 75 76 78
Weight Kg 5.1 5.1 5.1

Spare parts PVP 140 M / MLP PVP 170 M / MLP PVP 200 M / MLP
Sealing kit and reed valves item 00 KIT PVP 140 M 00 KIT PVP 170 M 00 KIT PVP 200 M
Exhaust silencer item 00 15 110 00 15 110 00 15 110
Silencer on nozzles item N°2 00 15 111 N°2 00 15 111 N°2 00 15 111
Vacuum gauge item 09 03 15 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25 09 03 25
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.89
MULTI-STAGE VACUUM GENERATORS PVP 140 M / MLP,
PVP 170 M / MLP and PVP 200 M / MLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
portata
PVP 140 M PVP 170 M portata PVP 200 M portata
PVP 140 MLP PVP 170 MLP PVP 200 MLP
3D drawings are available on vuototecnica.net

45
PVP 140 M PVP 140 MLP PVP 170 M PVP 170 MLP 60
PVP 200 M PVP 200 MLP
60

40
50 50
35

30 40 40

25
Nl/s

Nl/s
Nl/s
30 30
20

15 20 20

10
10 10
5

0 0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 140 M -Kpa PVP 170 M -Kpa PVP 200 M -Kpa
PVP 140 MLP PVP 170 MLP PVP 200 MLP

temp
portata
PVP 170 M temp PVP 200 M temp
PVP 140 M
PVP 140 M PVP 170 M portata PVP 200
200 M
MLP
PVP 140 MLP PVP 170 MLP PVP portata
PVP 140 MLP PVP 170 MLP
Air flow rate (Nl/s) at different levels of vacuums (-KPa)
PVP 200 MLP Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
700
1000
45 item bar Nl/s 800
60

900
0 10 20 30 40 5060 60 70 80 -KPa
40 700 600
PVP 140 M
800 6.0 13.0 50 42.20 30.10 20.10 10.00 7.18 5.7450 4.31 3.02 1.72 90
35 600
PVP 170 M
700 6.0 16.3 50.50 36.10 24.00 12.03 8.59 6.87
500
5.17 3.61 2.06 90
PVP 200 M
30
600
6.0 19.4 40
500 55.50 39.60 26.40 13.22 9.44 7.5540
400
5.68 3.97 2.27 90
25

Nl/sms/l
ms/l

400
ms/l

500
Nl/s

PVP 140 MLP 3.0 17.8 38.30 18.30 11.60 7.36 6.84 5.80 4.50 3.20 1.80 88
Nl/s

30 30
300
20
400
PVP 170 MLP 3.0 22.2 300
45.80 21.80 13.80 8.81 8.18 6.94 5.39 3.82 2.16 88
15
300 20 200
PVP 200 MLP 3.0 26.6 200 52.80 25.20 16.00 10.10 9.40 8.0020 6.20 4.40 2.50 88
200
10
100
10
100 10
100
5

0 0
0
0 0 10 20 30 40 50 60 70 80 85
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
-Kpa PVP 170 M -Kpa 0 PVP
10 20020M 30 -Kpa
40 50 60 70 80
PVP 140 M -Kpa
PVP 140 M PVP
PVP 170
170 MMLP -Kpa PVP 200 MLP
PVP 140 MLP PVP 200 M -Kpa
PVP 140 MLP PVP 170 MLP
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure PVP 200 MLP

temp
PVP 140 M PVP 170 M temp PVP 200 M temp
PVP 140 MLP PVP 170 MLP PVP 200 MLP

1000
PVP 140 M PVP 140 MLP 800
PVP 170 M PVP 170 MLP 700
PVP 200 M PVP 200 MLP
900
700 600
800
600
700 500

500
600
400
ms/l
ms/l

400
ms/l

500
300
400
300
300 200
200
200
100 100
100

0 0 0
8 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
PVP 140 M -Kpa PVP 170 M -Kpa PVP 200 M -Kpa
PVP 140 MLP PVP 170 MLP PVP 200 MLP

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 140 M 6.0 13.0 2.1 5.3 11.7 28.0 50.2 76.9 127.6 220.8 812 90
PVP 170 M 6.0 16.3 1.7 4.4 9.7 23.4 42.0 64.2 106.6 184.5 678 90
PVP 200 M 6.0 19.4 1.6 4.0 8.9 21.3 38.2 58.4 97.0 167.8 618 90

PVP 140 MLP 3.0 17.8 3.6 8.4 17.7 35.4 48.3 76.5 116.8 233.0 860 88
PVP 170 MLP 3.0 22.2 3.0 7.1 14.9 29.9 40.6 64.2 98.0 196.0 720 88
PVP 200 MLP 3.0 26.6 2.8 6.5 13.6 27.3 37.2 58.8 89.7 180.0 665 88

8.90
MULTI-STAGE VACUUM GENERATORS PVP 250 M / MLP and PVP 300 M / MLP

3D drawings are available on vuototecnica.net

Vacuum
gauge

Pressure
gauge

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 250 M PVP 300 M
Intake air flow rate m /h
3
224 252 280 240 290 320
Maximum level of vacuum -KPa 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6
Optimal supply pressure bar 6 6
Air consumption Nl/s 17.3 20.7 24.0 20.4 24.8 29.0
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 72 74
Weight Kg 6.0 6.0

Item PVP 250 MLP PVP 300 MLP

Intake air flow rate m3/h 120 185 250 128 210 300
Maximum level of vacuum -KPa 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120
Supply pressure bar 1 2 3 1 2 3
Optimal supply pressure bar 3 3
8
Air consumption Nl/s 16.0 25.0 33.6 19.1 28.8 39.3
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 77 78
Weight Kg 6.0 6.0

Spare parts PVP 250 M / MLP PVP 300 M / MLP

Sealing kit and reed valves item 00 KIT PVP 250 M 00 KIT PVP 300 M
Exhaust silencer item 00 15 110 00 15 110
Silencer on nozzles item N°3 00 15 111 N°3 00 15 111
Vacuum gauge item 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.91
MULTI-STAGE VACUUM GENERATORS PVP 250 M / MLP and PVP 300 M / MLP

portata

portata
Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
PVP 250 M PVP 300 M
PVP 250 MLP PVP 300 MLP
3D drawings are available on vuototecnica.net

90
PVP 250 M PVP 250 MLP 100
PVP 300 M PVP 300 MLP
80 90

80
70
70
60
60
50
50
Nl/s

Nl/s
40
40
portata
30
portata 30
PVP 250 M PVP 300 M
PVP 250 MLP 20 PVP 300 MLP
20

10 10
90 100
0 0
80 90
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 250 M -Kpa 80 PVP 300 M -Kpa
70 PVP 250 MLP PVP 300 MLP
70
60 temp
PVP 250 M temp
60
PVP 250 MLP 50 PVP 300 M
Air flow rate (Nl/s) Max vacuum
Generator Supp. press. Air consumption PVP 300 MLP 50 at different levels of vacuums (-KPa)
Nl/s

Nl/s

40 at optimal supply pressure

item
500 bar Nl/s 450
40
0 10 20 30 40 50 60 70 80 -KPa
30
450 3018.5
PVP 250 M 6.0 24.0 77.7 55.5 37.0 400 13.2 10.5 7.9 5.5 3.1 90
PVP 300
400M
20 6.0 29.0 88.8 63.4 42.3 2021.1
350
15.1 12.0 9.1 6.3 3.6 90
350
10 10
PVP 250 MLP 3.0 33.6 69.4 34.0 23.5 30014.0 11.5 9.8 7.6 5.3 3.0 88
300
PVP 300
0 MLP 3.0 39.3 83.3 41.5 27.5 017.0 14.5 11.4 8.8 6.1 3.4 88
0 10 20 30 40 50 60 70 80 250 0 10 20 30 40 50 60 70 80
ms/l

250
ms/l

PVP 250 M -Kpa PVP 300 M -Kpa

PVP 250 MLP 200 PVP 300 MLP
200
150
temp
150 temp
PVP 250 M Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
PVP 250 MLP PVP 300 M 100
100
PVP 300 MLP
50
500
PVP 250 M PVP 250 MLP 50 PVP 300 M PVP 300 MLP
450
0 0
450 10 20 30 40 50 60 70 80 85 400 10 20 30 40 50 60 70 80 85
PVP 250 M -Kpa PVP 300 M -Kpa
400
PVP 250 MLP 350 PVP 300 MLP
350
300
300
250
ms/l

250
ms/l

200
200
150
150

100 100

50 50
8
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
PVP 250 M -Kpa PVP 300 M -Kpa
PVP 250 MLP PVP 300 MLP

PVP 250 MLP 3.0 33.6 2.0 4.6 9.6 19.3 26.3 41.5 63.5 127.0 468.7 88
PVP 300 MLP 3.0 39.3 1.7 3.9 8.2 16.4 22.3 35.3 54.0 108.0 398.5 88

8.92
ACCESSORIES FOR VACUUM GENERATORS PVP 40 M / MLP ÷ PVP 300 M / MLP

3D drawings are available on vuototecnica.net

1 - COAXIAL SHUTTER SERVO-CONTROLLED SUPPLY VALVE

This is an innovative valve with coaxial shutter, pneumatically driven by the integrated vacuum switch on it, able to intercept the compressed air
supply to the vacuum generator, with operating pressures between 1.5 and 7 bar. The vacuum switch has the task of removing and returning a
pneumatic signal when a preset and adjustable level of vacuum is reached.
The pressure differential existing between the set maximum value and that of restoring the signal at rest is not adjustable and is equal to about 100 mbar.
The pneumatic vacuum switch, acting on the coaxial shutter supply valve automatically maintains the maximum and minimum level of vacuum
within the differential value.

For Ø 4 ext. hose

Connection to vacuum

For generator Weight

Item
item g
07 03 71 PVP 40 ÷ 300 M/MLP 355

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.93
ACCESSORIES FOR VACUUM GENERATORS PVP 40 M / MLP ÷ PVP 300 M / MLP

2 - REED VALVE KIT FOR CHECK DEVICE

ON VACUUM GENERATORS
This reed valve kit, specifically designed to be integrated on PVP 40 - 300 M/MLP vacuum generators, has the task of preventing the return
3D drawings are available on vuototecnica.net

of atmospheric air into the vacuum system (tanks, autoclaves, intake systems depression, vacuum cups, etc.), when the generator stops,
guaranteeing the seal and maintaining the level of vacuum reached in use.

For generator No. pc. Weight

Item
item g
00 KIT TRASM-MR PVP 40 ÷ 300 M/MLP 3 8

3 - FLEXIBLE TUBE FOR CONNECTION TO VACUUM

This flexible tube is fitted on one end with a 1/8 ”quick-fit coupling, to be screwed onto one of the two vacuum generator connections reserved
for the vacuum gauge, while the other free end is inserted into the fitting installed on the pneumatic vacuum switch. The task of this tube is to
continuously monitor the value of the level of vacuum reached in use and to transmit it to the vacuum switch.

For supply valve Weight

Item
item g
00 15 496 07 03 71 - 07 04 71 10

COMPLETE KIT FOR ENERGY SAVING DEVICE ES

The three components described above make up an energy saving kit for the compressed air supply ES (Energy Saving System). In fact, the ES
device acts directly on the generator, making it operate only within the preset vacuum values, thus limiting compressed air supply consumption;
all this entails considerable energy savings.
This kit has been designed for the PVP 40 - 300 M/MLP series of generators.
8

For generator Weight

Item
item g
ES 06 PVP 40 ÷ 300 M/MLP 380

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.94
MULTI-STAGE VACUUM GENERATORS PVP 25 MDX / MDXLP ÷ PVP 75 MDX / MDXLP

This line of generators is available with suction rates between 20 and

103 m3/h. The supply pressure goes from 4-6 bar for MDX items and
from 1-3 bar for MDXLP items. The maximum level of vacuum is -90
KPa. Characterised by their new generation of ejectors, boasting an

3D drawings are available on vuototecnica.net

excellent ratio between the quantity of air consumed and that suctioned,
benefiting operational consumption. They are fully made with anodised
aluminium, with stainless steel ejectors and screws. The tightness seal
is made from EPDM, while the reed valves are made as standard and in
VITON®, upon request. The “free-flow” SSX high sound damping silencers
installed as standard on the air exhaust.
They are equipped with additional threaded 4 M4 holes for fixing check valve
connections for increased points of usage
or for the installation of measurement or
control tools. Upon request, can be supplied
with a compressed air energy savings kit ES
(ENERGY SAVING SYSTEM), composed of a
pneumatic vacuum regulator, a pneumatic Housing for pneumatic
vacuum switch 12 02 30 X
coaxial shutter supply valve, a check valve
and necessary tubing.

Pressure Silencer
gauge

2 Ø 6.5 holes

Vacuum
gauge

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 25 MDX PVP 35 MDX PVP 50 MDX
Intake air flow rate m3/h 35 39 43 47 52 57 57 62 68
Maximum level of vacuum -KPa 65 82 90 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6 4 5 6
Optimal supply pressure bar 6 6 6
Air consumption Nl/s 2.3 2.8 3.2 3.4 4.1 4.8 4.7 5.6 6.5
Temperature of use °C -20 / + 80 -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 58 58 60
Weight Kg 1.71 1.73 1.75

Item PVP 25 MDXLP PVP 35 MDXLP PVP 50 MDXLP

Intake air flow rate m /h
3
20 28 35 26 38 47 31 48 58
Maximum level of vacuum -KPa 30 64 88 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120 700 360 120
Supply pressure bar
8
1 2 3 1 2 3 1 2 3
Optimal supply pressure bar 3 3 3
Air consumption Nl/s 2.2 3.3 4.4 3.4 5.0 6.5 4.5 6.6 8.6
Temperature of use °C -20 / +100 -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 62 68 74
Weight Kg 1.71 1.73 1.75

Spare parts PVP 25 MDX / MDXLP PVP 35 MDX / MDXLP PVP 50 MDX / MDXLP
Sealing kit and reed valves item 00 KIT PVP 25 MDX 00 KIT PVP 35 MDX 00 KIT PVP 50 MDX
Vacuum gauge item 09 03 15 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25 09 03 25
Silencer item SSX 3/4” SSX 3/4” SSX 3/4”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.95
MULTI-STAGE VACUUM GENERATORS PVP 25 MDX / MDXLP,
PVP 35 MDX / MDXLP and PVP 50 MDX / MDXLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply
portata
pressure

PVP 25 MDX portata PVP 35 MDX portata PVP 50 MDX

3D drawings are available on vuototecnica.net

PVP 25 MDXLP PVP 35 MDXLP PVP 50 MDXLP

14
PVP 25 MDX PVP 25 MDXLP 18
PVP 35 MDX PVP 35 MDXLP PVP 50 MDX PVP 50 MDXLP
20

16 18
12
14 16

10 14
12
12
8 10
10

Nl/s
Nl/s

Nl/s
6 8
8
6
4 6
4
4
2
2 2

0 0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 25 MDX -Kpa PVP 35 MDX -Kpa PVP 50 MDX -Kpa
PVP 25 MDXLP PVP 35 MDXLP PVP 50 MDXLP
portata

PVP 50 MDX temp

PVP 25 MDX portata PVP 35 MDX temp
PVP PVP 35
35 MDX
MDXLP PVP 50 MDXLP
PVP 25
25 MDXLP
MDX temp PVP portata PVP 50 MDX
PVP 25 MDXLP PVP 35 MDXLP Air flow rate (Nl/s) at different levels of vacuum (-KPa)
PVP 50 MDXLP Max vacuum
Generator Supp. press. Air consumption
14 3500 at optimal supply pressure20
4500 item bar Nl/s 18
0 10 20 30 40 503000
18 60 70 80 -KPa
12 3000
4000 16 16
PVP 25 MDX 6.0 3.2 11.9 8.5 5.7 2.8 2.0 1.6 2500
1.2 0.8 0.5 90
PVP 35 MDX
3500
10
6.0 4.8 2500
14
15.8 11.3 7.5 3.8 2.7 2.1 14
1.6 1.1 0.6 90
PVP 50 MDX
3000
8
6.0 6.5 12
2000
18.8 13.5 9.0 4.5 3.2 2.612
2000 1.9 1.4 0.7 90
10

ms/l Nl/s
Nl/sms/l
ms/lNl/s

2500 10
PVP 25 MDXLP
6 3.0 4.4 1500 9.7 4.7 3.5 2.2 2.0 1.7
1500
8 1.4 1.0 0.6 88
2000 8
PVP 35 MDXLP 3.0 6.5 13.0 6.2 4.7 3.0 2.7 2.3 6 1.8 1.3 0.7 88
4
1500 1000
PVP 50 MDXLP 3.0 8.6 6
16.1 7.7 5.8 3.7 3.3 2.8
1000
4
2.2 1.5 0.8 88
1000
2 4
500
2
500
500 2
0 0 0
0 10 20 30 40 50 60 70 80 10 20 30 40 50 60 70 80 85 0 10 20 30 40 50 60 70 80
0 0 0
10 PVP20
25 MDX
30 40 -Kpa
50 60 70 80 85 0 PVP
10 35 MDX
20 30 -Kpa
40 50 60 70 80 PVP 50 MDX -Kpa
10 PVP20 30
50 MDXLP 40 50 60 70 80 85
PVP 25 MDXLP PVP 35 MDXLP
PVP 25 MDX -Kpa PVP 35 MDX
PVP 50 MDX -Kpa -Kpa
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply
PVP 25 MDXLP PVP 35 MDXLP pressure
PVP 50 MDXLP
temp

PVP 25 MDX temp PVP 35 MDX temp PVP 50 MDX

PVP 25 MDXLP PVP 35 MDXLP PVP 50 MDXLP

4500
PVP 25 MDX PVP 25 MDXLP PVP 35 MDX PVP 35 MDXLP 3000
PVP 50 MDX PVP 50 MDXLP
3500

4000
3000
2500
3500
2500
3000 2000

2500 2000
ms/l

ms/l
ms/l

1500
2000
1500

1500 1000
1000
1000
500
500
500

0 0 0

8 10 20 30
PVP 25 MDX
40 50
-Kpa
60 70 80 85 10 20
PVP 35 MDX
30 40 50
-Kpa
60 70 80 85 10 20
PVP 50 MDX
30 40 50
-Kpa
60 70 80 85

PVP 25 MDXLP PVP 35 MDXLP PVP 50 MDXLP

Evacuation rates (ms/l= s/m3) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
at optimal supply pressure
item bar Nl/s
10 20 30 40 50 60 70 80 85 -KPa
PVP 25 MDX 6.0 3.2 7.5 18.8 41.3 99.3 177.7 271.9 451.4 781.0 2874 90
PVP 35 MDX 6.0 4.8 5.6 14.1 31.2 74.9 134.0 205.1 340.5 589.1 2618 90
PVP 50 MDX 6.0 6.5 4.7 11.9 26.2 62.8 112.4 172.0 285.5 494.0 1818 90

PVP 25 MDXLP 3.0 4.4 13.0 33.3 67.2 134.4 238.0 376.0 564.0 1128.0 4151 88
PVP 35 MDXLP 3.0 6.5 9.8 25.2 50.9 101.9 180.3 284.9 427.3 854.7 3145 88
PVP 50 MDXLP 3.0 8.6 7.9 20.3 41.0 82.0 145.3 229.5 344.3 688.5 2534 88

8.96
MULTI-STAGE VACUUM GENERATORS PVP 60 MDX / MDXLP and PVP 75 MDX / MDXLP

3D drawings are available on vuototecnica.net

4 M4 holes for fixing check valve

Housing for pneumatic

vacuum switch 12 02 30 X

Pressure Silencer
gauge

2 Ø 6.5 holes

Vacuum
gauge

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 60 MDX PVP 75 MDX
Intake air flow rate m3/h 75 85 92 85 94 103
Maximum level of vacuum -KPa 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6
Optimal supply pressure bar 6 6
Air consumption Nl/s 5.9 7.0 8.2 7.0 8.4 9.8
Temperature of use °C -20 / +80 -20 / +80
Noise level at
optimal supply pressure dB(A) 65 70
Weight Kg 1.90 1.92

Item PVP 60 MDXLP PVP 75 MDXLP

Intake air flow rate m /h
3
35 57 65 44 70 80
Maximum level of vacuum -KPa 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120
Supply pressure bar 1 2 3 1 2 3
8
Optimal supply pressure bar 3 3
Air consumption Nl/s 5.5 8.3 11.0 6.6 9.9 13.2
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 68 70
Weight Kg 1.90 1.92

Spare parts PVP 60 MDX / MDXLP PVP 75 MDX / MDXLP

Sealing kit and reed valves item 00 KIT PVP 60 MDX 00 KIT PVP 75 MDX
Vacuum gauge item 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25
Silencer item SSX 1” SSX 1”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.97
MULTI-STAGE VACUUM GENERATORS PVP 60 MDX / MDXLP and PVP 75 MDX / MDXLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
PVP 60 MDX portata PVP 75 MDX portata
PVP 60 MDXLP PVP 75 MDXLP
3D drawings are available on vuototecnica.net

30
PVP 60 MDX PVP 60 MDXLP 35
PVP 75 MDX PVP 75 MDXLP

30
25

25
20

20
Nl/s

Nl/s
15
15

10
PVP 75 MDX 10 portata
PVP 60 MDX portata PVP 75 MDXLP
PVP 60 MDXLP 5
5
35
30
0 0
0 10 20 30 40 50 60 70 80 30 0 10 20 30 40 50 60 70 80
PVP 60 MDX -Kpa PVP 75 MDX -Kpa
25 PVP 60 MDXLP PVP 75 MDXLP
25
PVP 60 MDX temp
20 temp
PVP 60 MDXLP PVP 75 MDX
Air flow rate (Nl/s)
20 at different vacuum levels (-KPa) Max vacuum
Generator Supp. press. Air consumption PVP 75 MDXLP
at optimal supply pressure
Nl/s

item bar Nl/s

Nl/s

15
2500 0 10 20 15 30 40 50 60 70 80 -KPa
2000
PVP 60 MDX 6.0 8.2 25.5 18.2 12.2 6.1 4.3 3.5 2.6 1.8 1.0 90
10 1800
10
PVP 75 MDX
2000 6.0 9.8 28.6 20.4 13.6 6.8 4.8 3.9 2.9 2.0 1.2 90
1600
5
PVP 60 5MDXLP 3.0 11.0 19.3 9.3 7.0 14004.4 4.0 3.4 2.7 1.9 1.0 88
PVP 75
1500MDXLP 3.0 13.2 22.5 10.8 8.1 5.1 4.6 3.9 3.1 2.2 1.2 88
0
1200
0 0 10 20 30 40 50 60 70 80
ms/l

0 10 20 30 40 50 60 70 80
ms/l

1000 PVP 75 MDX -Kpa

1000 PVP 60 MDX -Kpa PVP 75 MDXLP
PVP 60 MDXLP 800
Evacuation rates (ms/l =s/m3) at different levels of vacuums (-KPa) at optimal supply pressure
600temp
PVP 60 MDX temp PVP 75 MDX
500
PVP 60 MDXLP PVP 75 MDXLP
400

PVP 60 MDX PVP 60 MDXLP 200 PVP 75 MDX PVP 75 MDXLP

2500 2000
0
10 20 30 40 50 60 70 80 85 0
1800
PVP 60 MDX -Kpa 10 20 30 40 50 60 70 80 85
PVP 60 MDXLP 1600 PVP 75 MDX -Kpa
2000
PVP 75 MDXLP
1400

1500 1200
ms/l

ms/l

1000

1000 800

600

500 400
8 200

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
PVP 60 MDX -Kpa PVP 75 MDX -Kpa
PVP 60 MDXLP PVP 75 MDXLP

PVP 60 MDXLP 3.0 11.0 6.6 16.8 34.0 68.0 120.3 190.0 285.0 570.0 2098 88
PVP 75 MDXLP 3.0 13.2 5.7 14.5 29.2 58.4 103.4 163.4 245.0 490.3 1805 88

8.98
ACCESSORIES FOR VACUUM GENERATORS
PVP 25 MDX / MDXLP ÷ PVP 75 MDX / MDXLP

3D drawings are available on vuototecnica.net

2 4

1
4
3
1 - MINI PNEUMATIC VACUUM SWITCH
The vacuum switch has the task of removing a pneumatic signal when a specific adjustable level of vacuum is reached. The pressure differential
existing between the set maximum value and that of restoring the signal at rest is not adjustable and is equal to about 100 mbar.
The pneumatic vacuum switch, installed on the vacuum generators PVP 25 - 75 MDX / MDXLP acting on the coaxial shutter supply valve
automatically maintains the maximum and minimum level of vacuum within the differential value.

For generator Weight

Item
item g
12 01 30 X PVP 25 ÷ 75 MDX/MDXLP 104

2 - COAXIAL SHUTTER SERVO-CONTROLLED SUPPLY VALVE

These coaxial shutter valves, pneumatically driven by a vacuum switch or an alternative source, are able to intercept the compressed air supply
to the vacuum generators, with pressures between 1.5 and 7 bar. They must be chosen based on the generator power supply connection and the
required air quantity.

For Ø 4 ext. hose

Sp1 Sp2

A B Sp1 Sp2 For generator Weight

Item
Ø item g
07 01 71 G 1/4” 10 19 19 PVP 25 ÷ 50 MDX/MDXLP 72
07 02 71 G 3/8” 15 19 19 PVP 50 ÷ 75 MDX/MDXLP 70

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.99
ACCESSORIES FOR VACUUM GENERATORS
PVP 25 MDX / MDXLP ÷ PVP 75 MDX / MDXLP

3 - MEMBRANE CHECK VALVE M5 connection to mini pneumatic

3D drawings are available on vuototecnica.net

vacuum switch
A check valve specially designed to adapt to vacuum generators PVP
25 - 75 MDX / MDXLP.
The originality of this valve, besides its shape, consists in its
membrane seal component, which is able to guarantee very low
pressure drops, rapid intervention and perfect sealing.

4 TCCE M4 screws

G H L M Weight For generator

Item
Ø g item
10 04 20 G3/4” 35 75 41 165 PVP 25 ÷ 50 MDX / MDXLP
10 05 20 G1” 48 113 58 458 PVP 60 ÷ 75 MDX / MDXLP

4 - FLEXIBLE HOSE KIT WITH FITTINGS

This flexible hose kit is used to connect the mini vacuum switch to
the coaxial shutter supply valve and the membrane check valve. The
appropriate quick couplings are already assembled at the ends of the
tubes, to be screwed to the valve and vacuum switch connections.

For generator Weight

Item
item g
00 15 308 PVP 25 ÷ 75 MDX / MDXLP 16

8
COMPLETE KIT FOR ENERGY SAVING DEVICE ES

For generator Weight

Item
item g
ES 01 PVP 25 ÷ 50 MDX / MDXLP 475
ES 02 PVP 60 ÷ 75 MDX / MDXLP 998

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.100
SILENCERS

The use of natural fibre sound absorbing

material enclosed in special anodised
aluminium casings has allowed creating
this new range of silencers that

3D drawings are available on vuototecnica.net

considerably reduce noise made by air at
the vacuum generator exhaust.
There are two versions with different
lengths: the longer the length, the more
noise will be reduced.
Noise reduction: from -13 to -20 dB (A)
Working temperature: from -20 to +100°C

A B C C1 D d Weight
Item
Ø Ø Ø g
SSX 1/8” G1/8” 10 58 -- 17 7 14
SSX 1/4” G1/4” 10 60 -- 20 10 20
SSX 3/8” R G3/8” 7 57 -- 20 10 17 8
SSX 3/8” G3/8” 12 84 -- 29 16 52
SSX 1/2” G1/2” 14 106 -- 35 16 96
SSX 3/4” R G3/4” 14 106 -- 35 16 100
SSX 3/4” G3/4” 14 126 -- 50 21 174
SSX 1” G1” 14 146 -- 55 28 240
SSX 1” 1/2 G1” 1/2 30 210 -- 80 38 302
SSX 2” G2” 30 250 -- 90 48 372

2SSX 1/8” G1/8” 10 -- 104 17 7 28

2SSX 1/4” G1/4” 10 -- 108 20 10 40
2SSX 3/8” G3/8” 12 -- 154 29 16 104
2SSX 1/2” G1/2” 14 -- 196 35 16 192
2SSX 3/4” G3/4” 14 -- 236 50 21 348
2SSX 1” G1” 14 -- 276 55 28 480

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.101
MULTI-STAGE AND MODULAR VACUUM GENERATORS
PVP 150 MD / MDLP ÷ PVP 750 MD / MDLP - GENERAL DESCRIPTION
The special shape of these vacuum generators has allowed obtaining great suction
capacities in very limited overall dimensions.
The new design stainless steel ejectors are assembled on modular frames; the overlapping
of one or more frames defines the flow rate of the generators. They are supplied with a flow
3D drawings are available on vuototecnica.net

rate ranging from 85 e 900 m3/h and a maximum level of vacuum of -90KPa.
The supply pressure goes from 4-6 bar for MD items and from 1-3 bar
for MDLP items. Level of vacuum and flow rate can be adjusted according to the supply
air pressure. They are fully made with anodised aluminium.
The sealing gaskets and disc valves are EPDM as standard, but can be supplied in
VITON® upon request. Also upon request, an energy saving kit for the compressed air
ES (Energy Saving System) can be supplied. It is composed of a pneumatic coaxial
shutter valve for supply of the compressed air, an integrated pneumatic vacuum switch,
a reed valve kit for the check system and a flexible tube with quick fitting to monitor and
transmit the value of the level of vacuum to the vacuum switch.
Perfectly soundproofed with silencers built into all generators, offering extremely quiet
operation.

8.102
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 150 MD / MDLP
and PVP 300 MD / MDLP

Pressure Vacuum

3D drawings are available on vuototecnica.net

gauge gauge
For Ø 15 ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 150 MD PVP 300 MD
Intake air flow rate m /h3
160 180 200 320 360 400
Maximum level of vacuum -KPa 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6
Optimal supply pressure bar 6 6
Air consumption Nl/s 12.1 14.2 16.0 23.2 27.8 32.0
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 72 74
Weight Kg 7.0 8.0
A 80 100
G Ø G1” 1/2 G2”
L 125 145

Item PVP 150 MDLP PVP 300 MDLP

Intake air flow rate m /h3
85 146 170 190 300 340
Maximum level of vacuum -KPa 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120
Supply pressure bar 1 2 3 1 2 3
Optimal supply pressure bar 3 3
Air consumption Nl/s 10.5 16.5 22.6 22.5 33.6 45.5
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 76 78 8
Weight Kg 7.8 8.8
A 80 100
G Ø G1” 1/2 G2”
L 125 145

Spare parts PVP 150 MD / MDLP PVP 300 MD / MDLP

Sealing kit and reed valves item 00 KIT PVP 150 MD 00 KIT PVP 300 MD
Exhaust silencer item 00 15 70 00 15 70
Silencer on nozzles item 00 15 71 00 15 72
Vacuum gauge item 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter R to the item for a generator supplied with an integrated check valve (Example: PVP 150 MDR).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.103
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 150 MD / MDLP
and PVP 300 MD / MDLP

PVP 150 MD portata Air flow rate (Nl/s) at differentPVP

levels of vacuums portata
300 MD (-KPa) at optimal supply pressure
PVP 150 MDLP PVP 300 MDLP
3D drawings are available on vuototecnica.net

60
PVP 150 MD PVP 150 MDLP 120
PVP 300 MD PVP 300 MDLP

50 100

40 80

Nl/s
Nl/s

30 60

20 PVP 300 MD 40
PVP 150 MD portata portata
PVP 300 MDLP
PVP 150 MDLP
10 20
120
60

0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
50
100
PVP 150 MD -Kpa PVP 300 MD -Kpa
PVP 150 MDLP PVP 3000 MDLP

40 80

PVP 150 MD temp PVP 300 MD

Max vacuum
PVP 300Air flow rate (Nl/s)
60 at different levels of vacuums (-KPa)
temp
Nl/s
PVP 150 MDLP Generator Supp. press. Air consumption MDLP
Nl/s

30
at optimal supply pressure
item bar Nl/s
1000
0 10 20 30 40 50 60 70 80 -KPa
20 40
700
PVP 150 MD 6.0 16.0 55.5 39.6 26.5 13.2 9.4 7.5 5.7 4.0 2.3 90
900
PVP 300 MD 6.0 32.0 111.1 79.4 52.9 600
26.5 19.9 15.1 11.4 7.9 4.5 90
10 20
800

PVP 150
700 MDLP 3.0 22.6 47.2 24.5 15.9 500
10.3 9.3 7.5 4.7 3.2 1.8 88
PVP 3000 MDLP 3.0 45.5 94.4 49.0 31.9 0 20.7 18.6 15.1 9.3 6.5 3.7 88
600 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 150 MD -Kpa 400 PVP 300 MD -Kpa
PVP 3000 MDLP
ms/l

500
ms/l

PVP 150 MDLP

400 300

300 temp Evacuation rates (ms/l =s/m3) at different

PVP 300 levels
MD of vacuums
temp
(-KPa) at optimal supply pressure
PVP 150 MD 200
PVP 300 MDLP
PVP 150 MDLP
200

100
1000
PVP 150 MD PVP 150 MDLP 100
700
PVP 300 MD PVP 300 MDLP
0
900 0
10 20 30 40 50 60 70 80 85 600 10 20 30 40 50 60 70 80 85
800 PVP 150 MD -Kpa PVP 300 MD -Kpa
PVP 150 MDLP PVP 300 MDLP
700 500

600
400
ms/l
ms/l

500
300
400

300 200

200
100
8 100

0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
PVP 150 MD -Kpa PVP 300 MD -Kpa
PVP 150 MDLP PVP 300 MDLP

PVP 150 MDLP 3.0 22.6 2.9 7.5 15.0 30.1 53.3 84.2 126.3 252.5 930 88
PVP 300 MDLP 3.0 45.5 2.0 5.2 10.5 21.0 37.2 58.7 88.0 176.1 650 88

8.104
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 450 MD / MDLP
and PVP 600 MD / MDLP

3D drawings are available on vuototecnica.net

Pressure Vacuum
gauge gauge
For Ø 22 ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 450 MD PVP 600 MD
Intake air flow rate m /h3
490 530 580 640 700 750
Maximum level of vacuum -KPa 65 82 90 65 82 90
Final pressure abs. mbar 350 180 100 350 180 100
Supply pressure bar 4 5 6 4 5 6
Optimal supply pressure bar 6 6
Air consumption Nl/s 35.4 40.6 47.8 45.4 56.8 63.2
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 74 78
Weight Kg 9.1 10.3
A 122 142
G Ø G2” 1/2 G3”
L 167 187

Item PVP 450 MDLP PVP 600 MDLP

Intake air flow rate m /h3
250 440 500 330 590 670
Maximum level of vacuum -KPa 30 64 88 30 64 88
Final pressure abs. mbar 700 360 120 700 360 120
Supply pressure bar 1 2 3 1 2 3
Optimal supply pressure bar 3 3
Air consumption Nl/s 32.0 48.8 65.8 42.0 66.0 87.7
Temperature of use °C -20 / +100 -20 / +100
Noise level at
optimal supply pressure dB(A) 80 82 8
Weight Kg 9.1 10.3
A 122 142
G Ø G2” 1/2 G3”
L 167 187

Spare parts PVP 450 MD / MDLP PVP 600 MD / MDLP

Sealing kit and reed valves item 00 KIT PVP 450 MD 00 KIT PVP 600 MD
Exhaust silencer item 00 15 70 00 15 70
Silencer on nozzles item 00 15 71 + 00 15 72 N°2 00 15 72
Vacuum gauge item 09 03 15 09 03 15
Pressure gauge item 09 03 25 09 03 25
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter R to the item for a generator supplied with an integrated check valve (Example: PVP 450 MDR).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.105
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 450 MD / MDLP
and PVP 600 MD / MDLP

Air flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
PVP 450 MD portata PVP 6000 MD portata
PVP 450 MDLP PVP 600 MDLP
3D drawings are available on vuototecnica.net

180
PVP 450 MD PVP 450 MDLP PVP 600 MD PVP 600 MDLP
250

160

200
140

120
150
100
Nl/s

Nl/s
80
PVP 6000 MD 100
portata
60 PVP 600 MDLP
PVP 450 MD portata
40
PVP 450 MDLP 50
250
20
180
0 0
200
160 0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
PVP 450 MD -Kpa PVP 600 MD -Kpa
140 PVP 450 MDLP PVP 600 MDLP
150
120
PVP 450 MD
Nl/s
temp
PVP 450 MDLP
100 Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption 100
PVP 600 MD at optimal
temp supply pressure
Nl/s

item
80
450 bar Nl/s PVP 600 MDLP
0 10 20 30 40 50 60 70 80 -KPa
PVP 450
60 MD
400 6.0 47.8 161.1 115.0 76.7 5038.3
300
27.4 21.9 16.5 11.5 6.6 90
PVP 600
40
MD 6.0 63.2 208.3 148.8 99.2 49.6 35.4 28.3 21.3 14.9 8.5 90
350
250
0
PVP 450
20 MDLP
300 3.0 65.8 138.8 72.7 46.9 30.50 27.4
10 20
22.230 13.8
40 50
9.6 60 5.570 80
88
PVP 600 MDLP 3.0 87.7 186.1 96.7 62.9 40.8 36.8
PVP 600 MD29.8 18.5
-Kpa 12.9 6.8 88
0
250
200 PVP 600 MDLP
0 10 20 30 40 50 60 70 80
ms/l

200 PVP 450 MD -Kpa

PVP 450 MDLP
ms/l

150
150

PVP 450 MD temp

Evacuation rates (ms/l =s/m3) at different
PVP 600levels
MD of vacuums
temp (-KPa) at optimal supply pressure
100 PVP 600 MDLP 100
PVP 450 MDLP

50
450
PVP 450 MD PVP 450 MDLP PVP 600 MD PVP 600 MDLP
300
50
0
400 10 20 30 40 50 60 70 80 85
PVP 450 MD -Kpa 250
0
350 PVP 450 MDLP 10 20 30 40 50 60 70 80 85
PVP 600 MD -Kpa
300 200 PVP 600 MDLP

250
ms/l
ms/l

150
200

150 100

100
50
50
8
0 0
10 20 30 40 50 60 70 80 85 10 20 30 40 50 60 70 80 85
PVP 450 MD -Kpa PVP 600 MD -Kpa
PVP 450 MDLP PVP 600 MDLP

PVP 450 MDLP 3.0 65.8 1.2 3.0 6.2 12.4 22.0 34.7 52.0 104.1 383 88
PVP 600 MDLP 3.0 87.7 0.8 2.0 4.1 8.2 14.6 23.1 34.7 69.4 256 88

8.106
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 750 MD / MDLP

3D drawings are available on vuototecnica.net

Pressure Vacuum
gauge gauge
For Ø 22 ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVP 750 MD
Intake air flow rate m /h3
650 780 900
Maximum level of vacuum -KPa 65 82 90
Final pressure abs. mbar 350 180 100
Supply pressure bar 4 5 6
Optimal supply pressure bar 6
Air consumption Nl/s 60.5 71.0 80.0
Temperature of use °C -20 / +80
Noise level at
optimal supply pressure dB(A) 84
Weight Kg 12.7
A 164
G Ø G3”
L 209

Item PVP 750 MDLP

Intake air flow rate m /h3
420 650 800
Maximum level of vacuum -KPa 30 64 88
Final pressure abs. mbar 700 360 120
Supply pressure bar 1 2 3
Optimal supply pressure bar 3
Air consumption Nl/s 52.0 82.5 110.0
Temperature of use °C -20 / +100
Noise level at
optimal supply pressure dB(A) 85 8
Weight Kg 12.7
A 164
G Ø G3”
L 209

Spare parts PVP 750 MD / MDLP

Sealing kit and reed valves item 00 KIT PVP 750 MD
Exhaust silencer item 00 15 70
Silencer on nozzles item N°2 00 15 72 + 00 15 71
Vacuum gauge item 09 03 15
Pressure gauge item 09 03 25
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter R to the item for a generator supplied with an integrated check valve (Example: PVP 750 MDR).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.107
MULTI-STAGE AND MODULAR VACUUM GENERATORS PVP 750 MD / MDLP

PVP Air
750 MD
flow rate (Nl/s) at different levels of vacuums (-KPa) at optimal supply pressure
portata
PVP 750 MDLP
3D drawings are available on vuototecnica.net

PVP 750 MD PVP 750 MDLP

300

250

200
Nl/s

PVP 750 MD 150

portata
PVP 750 MDLP

100
300

50
250

0
0 10 20 30 40 50 60 70 80
200
PVP 750 MD -Kpa
PVP 750 MDLP
Nl/s

150 temp
PVP 750 MD
PVP 750 MDLP
Air flow rate (Nl/s) at different levels of vacuums (-KPa) Max vacuum
Generator Supp. press. Air consumption
100 at optimal supply pressure
item bar Nl/s
180 0 10 20 30 40 50 60 70 80 -KPa
PVP 750 MD 6.0 50 80.0 250.0 180.0 118.8 59.4 42.8 34.2 25.7 18.0 10.2 90
160
PVP 750 MDLP 3.0 110.0 222.2 115.5 75.1 48.8 43.9 35.6 22.0 15.4 8.8 88
140
0
0 10 20 30 40 50 60 70 80
120
PVP 750 MD -Kpa
PVP 750 MDLP
100
ms/l

Evacuation temp ) at different levels of vacuums (-KPa) at optimal supply pressure

PVP 750 MDrates (ms/l =s/m
3

80
PVP 750 MDLP

60
PVP 750 MD PVP 750 MDLP
180
40

160
20

140
0
10 20 30 40 50 60 70 80 85
120
PVP 750 MD -Kpa
PVP 750 MDLP
100
ms/l

8 40

0
10 20 30 40 50 60 70 80 85
PVP 750 MD -Kpa
PVP 750 MDLP

8.108
ACCESSORIES FOR VACUUM GENERATORS PVP 150 MD / MDLP ÷ PVP 750 MD / MDLP

3D drawings are available on vuototecnica.net

3 2

1 - COAXIAL SHUTTER SERVO-CONTROLLED SUPPLY VALVE

For Ø 4 ext. hose

Connection to vacuum
Sp36
8
Adjustment
screw

For generator Weight

Item
item g
07 04 71 PVP 150 ÷ 750 MD/MDLP 570

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.109
ACCESSORIES FOR VACUUM GENERATORS PVP 150 MD / MDLP ÷ PVP 750 MD / MDLP

2 - REED VALVE KIT FOR CHECK DEVICE

ON VACUUM GENERATORS
This reed valve kit, specifically designed to be integrated on PVP 150/750 MD/MDLP vacuum generators, has the task of preventing the return
3D drawings are available on vuototecnica.net

For generator No. pc. Weight

Item
item g
00 KIT TRASMD-MDR PVP 150 ÷ 750 MD/MDLP 6 16

3 - FLEXIBLE TUBE FOR CONNECTION TO VACUUM

For supply valve Weight

Item
item g
00 15 496 07 03 71 - 07 04 71 10

COMPLETE KIT FOR ENERGY SAVING DEVICE ES

The three components described above make up an energy saving kit for the compressed air supply ES (Energy Saving System). In fact, the ES
device acts directly on the generator, making it operate only within the preset vacuum values, thus limiting compressed air supply consumption;
all this entails considerable energy savings.
This kit has been specifically designed for the PVP 150-750 MD/MDLP series of generators.
8

For generator Weight

Item
item g
ES 05 PVP 150 ÷ 750 MD/MDLP 596

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.110
CONVEYOR ADJUSTABLE VACUUM GENERATORS

Working principle
These vacuum generators operate based on the Venturi principle.
Unlike those previously described, the ejectors with which they are supplied are adjustable, in addition to
having a considerably higher flow diameter.

3D drawings are available on vuototecnica.net

This detail lets them vary the flow rate and level of vacuum of the device, without altering the level of
vacuum of the supply air.
The compressed air consumption is also related to the actual performance of the vacuum generator.
Features
The special shape of these adjustable vacuum generators, as well as their straight-flow working principle
allow sucking and transferring products of various nature with no interference, just like flow generators,
only, unlike these, they allow overcoming much higher level differences.
They are suited for transferring powders, granulated products, sawdust, metal chips, dry or liquid food
products, etc. They are also recommended for controlling vacuum cups in presence of large amounts of
dust or liquids, as well as for sucking fumes, cooling mists, water and oil condensation, etc. The absence of
moving parts allows for a continuous use without developing heat.
The noise level, which is quite high for this kind of equipment, can be considerably reduced with a silencer
screwed on the exhaust connection.
They do not require electricity, therefore, they can even be used in work environments with hazardous
environments where an ignition source would be dangerous.
Available in anodised aluminium and stainless steel.
Thanks to all these features, a good filtration of the compressed air supply will be sufficient to make these
devices fully maintenance-free.

For ØD ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVR 25 PVR 50
Max quantity of intake air at 5 bar m3/h 13.0 36.0
Max quantity of air blown at 6 bar m3/h 33.5 88.0
Maximum level of vacuum -KPa 80 75
Final pressure abs. mbar 200 250
Maximum supply pressure bar 6 6
Maximum air consumption at 6 bar Nl/s 6.1 15.5
Temperature of use °C -20 / +80 -20 / +80
Noise level dB(A) 92 98 8
Weight g 150 280
A Ø 19 26
B Ø 32 38
D Ø 6 8
E 19 35
F 47 54
G Ø G1/4” G3/8”
G1 Ø G1/4” G1/2”
H 34 61
L 100 150
M 22 25
N Ø 6 10
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter I, to the item for a generator supplied in stainless steel (Example: PVR 50 I).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.111
PVR 25 Quantità di aria aspirata (mc/h) PVR 50 Quantità di aria aspirata (mc/h)
PVR 25 Quantità di aria aspirata (mc/h) PVR 50 Quantità di aria aspirata (mc/h)

ADJUSTABLE
PVR 25 CONVEYOR VACUUM
Quantità di aria aspirata (mc/h) GENERATORS PVR 25 and
PVR 50 PVR
Quantità 50aspirata (mc/h)
di aria
14 40

PVR 25 Quantità di aria aspirata (mc/h) PVR

40 50 Quantità di aria aspirata (mc/h)
14
12 Quantity of air suctioned (m /h) at different
3
35 supply pressures (bar)
14
12 35
40
30
10

14
PVR 25 30
35
PVR 50
12
10 40
25
8
3D drawings are available on vuototecnica.net

25
30
m3/h m3/h

m3/h m3/h
12 35
20
10
8
6
20
25
30
15
10
8
6
4
m3/h

m3/h
15
20
25
10
8
6
4
2
m3/h

m3/h
15
205
6
4
2
0 105
150
1 2 3 4 5 6 1 2 3 4 5 6
4
2
0 bar 100
5 bar
1 2 3 4 5 6 1 2 3 4 5 6
2 bar bar
0 0
5
PVR 25 1 Quantità
2 di aria
3 soffiata
4 5 6
PVR 50 1 2 3
Quantità 4 soffiata
di aria 5 6
bar bar
0 0
PVR 25 1 Quantità
2 di aria
3 soffiata
4 5 6 PVR 50 1 2 Quantità
3 di aria
4 soffiata
5 6
bar bar
PVR 25 Quantità di aria soffiata PVR 50 Quantità di aria soffiata
40
Quantity of air blown (m3/h) at different90 supply pressures (bar)
PVR 25 40 Quantità di aria soffiata 90 50
PVR
80 Quantità di aria soffiata
35

35
PVR 25 80
70
PVR 50
40
30 90

70
60
80
30
35
40
25 90
60
50
70
25
30 80

m3/h m3/h
m3/h m3/h

35
20
50
40
60
20 70
25
30
15
40
30
50
60
m3/h
m3/h

15
20
25
10
30
20
40
50
10
m3/h
m3/h

15
20
5 20
10
30
40
5
10
15
0 10
0
20
1 2 3 4 5 6 30 1 2 3 4 5 6
0
5
10 bar 0
10 bar
1 2 3 4 5 6 20 1 2 3 4 5 6
bar bar
0
5 0
10
PVR 25 1 Grado
2 di3 vuoto4 5 6 PVR 50 1 2 3Grado di
4 vuoto5 6
bar bar
0 0
PVR 25 1
Grado
2
di3 vuoto4 5 6
PVR 50 1 2 3Grado di
4 vuoto5 6
Level of vacuum (-Kpa) at different supply pressures (bar)
bar bar
PVR 25 Grado di vuoto PVR 50 Grado di vuoto
90 80

PVR 25
PVR 25
Grado di vuoto PVR
PVR 50
Grado di vuoto
90
80 80 50 70

80
70
90 70
80
60

70
60
80
90 60
70
80
50
60
50
70
80 50
-Kpa -Kpa -Kpa
-Kpa -Kpa -Kpa

60
70
40
50
40
60
70 40
50
60
30
40
30
50
60
30
40
50
20
30
20
40
50
-Kpa
-Kpa

20
30
40
10
20
10
30
40
10
0 10
20
30
0
20
30 1 2 3 4 5 6 1 2 3 4 5 6
0
10 bar 0
10
20 bar
20 1 2 3 4 5 6 1 2 3 4 5 6
0 bar bar
0 50 Consumo d'aria
PVR 25 10
1
Consumo
2 3
d'aria4 5 6
10
PVR
1 2 3 4 5 6

PVR 25 Air consumption (Nl/s) at different PVR

bar
Consumo d'aria supply
0 50
pressures (bar)
Consumo
bar d'aria
8 0
1 2 3 4 5 6 1 2 3 4 5 6
PVR 25
7
PVR 25
bar
Consumo d'aria PVR 50
18
PVRbar
50 d'aria
Consumo

PVR 25 Consumo d'aria PVR 50 Consumo d'aria

7 18
16
6

7 16
14
18
6
5
14
12
16
7
6 18
5
4 12
10
14
16
Nl/s Nl/s
Nl/s Nl/s

6
5
4 10
3 8
12
14
5
4 8
6
3 10
2 12
Nl/s
Nl/s

46
8
4
3 10
2
1
Nl/s
Nl/s

42
6
3 8
2
1
0 2
40
1 2 3 4 5 6 6 1 2 3 4 5 6
2
1
0 bar 0
2 bar
1 2 3 4 5 6 4 1 2 3 4 5 6
1 bar bar
0 0
2
1 2 3 4 5 6 1 2 3 4 5 6
bar bar
0 0
8.112 1 2 3 4 5 6 1 2 3 4 5 6
bar bar
ADJUSTABLE CONVEYOR VACUUM GENERATORS PVR 100 and PVR 200

3D drawings are available on vuototecnica.net

For ØD ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVR 100 PVR 200
Max quantity of intake air at 5 bar m3/h 50 72
Max quantity of air blown at 6 bar m3/h 129 177
Maximum level of vacuum -KPa 75 70
Final pressure abs. mbar 250 300
Maximum supply pressure bar 6 6
Maximum air consumption at 6 bar Nl/s 22.7 28.3
Temperature of use °C -20 / +80 -20 / +80
Noise level dB(A) 100 104 8
Weight g 430 550
A Ø 32 38
B Ø 50 57
D Ø 10 12
E 35 35
F 60 60
G Ø G1/2” G3/4”
G1 Ø G3/4” G1”
H 55 77
L 150 172
M 28 28
N Ø 12.5 16.0
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter I, to the item for a generator supplied in stainless steel (Example: PVR 100 I).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.113
ADJUSTABLE CONVEYOR VACUUM GENERATORS80 PVR 100 and PVR 200
60

60 80
Quantity of air suctioned (m3/h) at different
70 supply pressures (bar)
50
60 70
80
60
50
40 PVR 100 60
70
80
PVR 200
60 50
50
40
3D drawings are available on vuototecnica.net

50
60
m3/h m3/h

m3/h m3/h
30 70
40
50
40
30 40
50
60
30
20
40
m3/h

m3/h
30 30
40
50
20
20
10
20
30
m3/h

m3/h
30 40
10
20
10
0 10
20
30
0
20 1 2 3 4 5 6 1 2 3 4 5 6
10
0 bar 0
10
20 bar
1 2 3 4 5 6 1 2 3 4 5 6
10 bar bar
0 0
10
1 2 3 4 5 6 1 2 3 4 5 6
bar bar
0 0
1 2 3 4 5 6 1 2 3 4 5 6
bar bar

140 200
Quantity of air blown (m3/h) at different supply pressures (bar)
140 180
200
120

140
PVR 100 160
180
200
PVR 200
120
100 140
160
180
140
120 200
100 120
140
80 160
180
m3/h m3/h

m3/h m3/h
120 100
120
100
80 140
60 160
80
100
120
100
80 140
60 60
40 80
m3/h

m3/h

100
120
80
60 40
60
40 80
20
m3/h

m3/h

100
20
40
60
40 60
20 80
0 0
20
1 2 3 4 5 6 40 1 2 3 4 5 6
40 60
20
0 bar 0 bar
1 2 3 4 5 6 20 1 2 3 4 5 6
40
20 bar bar
0 0
1 2 3 4 5 6 20 1 2 3 4 5 6
bar bar
0 0
1 2 3 4 5 6 1 2 3 4 5 6
Level of vacuum (-Kpa) at different supply pressures (bar)
bar bar

80 70
PVR 100 70
PVR 200
80
70 60

70
80
60 70
60
50
60
70
50
80 70
60
50
40
50
-Kpa -Kpa

-Kpa -Kpa

60
40
70 60
50
40
30
40
50
30
60
50
40
30
20
-Kpa

-Kpa

30
40
20
50
40
30
20
20 10
-Kpa

-Kpa

30
10
40
30
20
10
10
20
0
30 0
1 2 3 4 5 6 1 2 3 4 5 6
20
10
0
10
20 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6
bar 10
0 bar
0
10
1 2 3 4 5 6 1 2 3 4 5 6
Air
bar consumption (Nl/s) at different supply pressures (bar)
bar
8 0
1 2 3 4 5 6
0
1 2 3 4 5 6

25
PVRbar 100 35
PVRbar200
25 35
30
20
25 35
30
25
20
25 35
30
15 25
20 20
Nl/s Nl/s
Nl/s Nl/s

15 30
25
20
20 15
10
15 25
20
15
10 10
Nl/s
Nl/s

15
5 20
15
10 10
5
Nl/s
Nl/s

5
15
10
10 5
0 0
5 1 2 3 4 5 6 1 2 3 4 5 6
bar 10
5 bar
0 0
5 1 2 3 4 5 6 1 2 3 4 5 6
bar 5 bar
0 0
1 2 3 4 5 6 1 2 3 4 5 6
bar bar
0 0
8.114 1 2 3 4 5 6 1 2 3 4 5 6
bar bar
CARTRIDGE VACUUM GENERATORS PVR 1 and PVR 4

These small cartridge vacuum generators can be

integrated directly into the gripping elements of
packaging machines.
The maximum yield is offered at low compressed air

3D drawings are available on vuototecnica.net

pressures of 2-3 bar, providing levels of vacuums up
to -72 KPa and flow rates between 1 and 4 m3/h.
Their particular shape permits the suction of dust or
small processing residues, without creating clogging
problems.
They are made as standard in anodised aluminium
but can also be supplied in stainless steel, upon
request.

Cross-housing for
screwdriver

CREATION OF HOUSING FOR CARTRIDGE INSERTION

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVR 1 PVR 4
Intake air flow rate m /h3
0.6 0.8 0.9 2.7 3.3
Maximum level of vacuum -KPa 19 41 60 30 72 8
Final pressure abs. mbar 810 590 400 700 280
Supply pressure bar 1 2 3 1 2.5
Air consumption Nl/s 0.3 0.5 0.6 1.7 2.9
Temperature of use °C -10 / +80 -10 / +80
Noise level dB(A) 68 80
Weight g 4 16
d Ø 7.8 13.5
D Ø 8.7 14.8
L 26 52
F 9.3 15
G Ø G1/8” G3/8”
H Ø M5 G1/8”
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter I, to the item for a generator supplied in stainless steel (Example: PVR 4 I).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.115
CARTRIDGE VACUUM GENERATOR PVR 3 OT

Also the construction of this cartridge vacuum generator was necessary in order to meet the demand for
ever smaller and more performing devices in the packaging sector.
The compressed air supply pressure is between 1 and 3 bar, while the maximum level of vacuum is -52
KPa, with a flow rate of 2.6 m3/h.
3D drawings are available on vuototecnica.net

Also the shape of these generators, like the previous ones described, allows for the suction of dust and
small processing waste without clogging problems.
They are made of brass as standard, but upon request they can also be supplied in different metals.

Sp17

CREATION OF HOUSING FOR CARTRIDGE INSERTION

Item PVR 3 OT
Intake air flow rate m /h
3
2.2 2.6 2.6 2 1.6
Maximum level of vacuum -KPa 21 37 52 50 47
Final pressure abs. mbar 790 630 480 500 530
Supply pressure bar 1 2 3 4 5
Air consumption Nl/s 1.25 1.8 2.4 3.1 3.6
Temperature of use °C -10 / +60
Noise level dB(A) 78
Weight g 60
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.116
CONVEYOR VACUUM GENERATOR PVR 25 MS, WITH SUPPORT FOR FASTENING TO
VACUUM CUPS
The particular shape of this rectilinear flow vacuum generator allows for the supply of vacuum cups,
especially in the presence of abundant quantities of dust, liquids, sawdust, of various origins, and shavings,
without interference. It can reach a level of vacuum of -70KPa, a suction flow rate of about 10 m3/h, with a
supply pressure of 3 bar.

3D drawings are available on vuototecnica.net

The support it is equipped with allows it to be fixed to flat vacuum cups, starting from Ø 200 mm, while
a special adapter, available upon request, allows the generator to be fixed at a distance. A "free-flow"
silencer is installed on the intake air exhaust with high sound reduction, equipped with appropriate safety
protection to prevent the dispersion of the sucked solid impurities in the work environment.
Also upon request, it is possible to supply a digital micro vacuum switch, item 12 05 11 P, for checking the
level of vacuum inside the vacuum cup, and a vacuum gauge item 09 03 15, for direct reading of the level.
A good filtration of the compressed air supply will be sufficient to make these devices fully maintenance-
free. Their use is recommended in particular on vacuum cups for gripping marble and granite, bricks, rusty
metal sheets, rough wooden boards and anything else with especially dirty gripping surfaces.

Vacuum gauge item 09 03 15

(upon request)
Housing for O-ring
item 000735

Protection plate
Vacuum switch item 12 05 11 P item 00 15 341
(upon request)
Silencer
item SSX 1/4”

8
Adapter item 00 15 397
(upon request)

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item PVR 25 MS
Intake air flow rate m /h
3
6.4 9.4 9.6
Maximum level of vacuum -KPa 12 45 70
Final pressure abs. mbar 880 550 300
Supply pressure bar 1 2 3
Air consumption Nl/s 8.2 10.87 12.49
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.117
ACCESSORIES AND SPARE PARTS FOR VACUUM GENERATOR PVR 25 MS

Digital micro vacuum switch

Vacuum Manifold (anodised aluminium)

3D drawings are available on vuototecnica.net

connection
Body (polycarbonate)

Red LED
Three-pole shielded cable
Adjustment Ø3.2 L=1500 mm
screw

Item Description
12 05 11 P Digital micro vacuum switch

Vacuum gauge
sp14

Scale Double Scale Admissible error Temperature of Notes Material Weight

Item
KPa on the scale use of case g
09 03 15 0 ÷ -100 -- 2.5% -10 °C ÷ +50 °C 52

Threaded adapter for suction mouth item 00 15 397

M 4 THROUGH-HOLE

8
SPARE PARTS

Safety protection for exhaust silencer SSX 1/4” item 00 15 341

8.118
ACCESSORIES FOR CONVEYOR ADJUSTABLE VACUUM GENERATORS

The noise level of Conveyor adjustable vacuum generators, which is always quite high,
can be considerably mitigated by a suitable silencer screwed onto the air exhaust
connection. SSX series silencers can be supplied upon specific request. These are
suitable for all Conveyor vacuum generators.

3D drawings are available on vuototecnica.net

The table below shows the codes of the silencers related to the various vacuum
generators.

PVR 25 with exhaust silencer SSX 1/4” and vacuum cup 08 53 35 S

PVR 50 with exhaust silencer 2SSX 1/2”

PVR 100 with exhaust silencer SSX 3/4”

Silencer Noise reduction Silencer Noise reduction

Item
item dB(A) item dB(A)
PVR 25 SSX 1/4” -13 2SSX 1/4” -20
PVR 50 SSX 1/2” -13 2SSX 1/2” -20
PVR 100 SSX 3/4” -13 2SSX 3/4” -20
PVR 200 SSX 1” -13 2SSX 1” -20

8.119
VACUUM JET FLOW GENERATORS

Working principle
The compressed air supply blown into a ring chamber concentric to the device, flows at
a very high speed towards the centre of the main pipe, thus forming a cyclonic effect.
The latter creates a vacuum inside the device and leads a great volume of air towards its
3D drawings are available on vuototecnica.net

outlet.
Therefore, a variation of the air supply pressure will modify the level of vacuum and the
amount of sucked air.
Features
The special shape of the flow generators and their straight-flow working principle allow
for the suctioning and handling of various nature products without interference. Vacuum
Jets are in fact suitable for the handling of powders, granulated products, sawdust, corn,
metal chips, liquid or dry food products, etc., or for extracting fumes, coolant mists,
water or oil condensation, etc.
The absence of moving parts allows them to be used continuously, without developing
heat.
They do not require electricity; therefore, they can be used in work environments with
hazardous environments where an ignition source would be dangerous.
Available in anodised aluminium and stainless steel.
Thanks to all these features, a good filtration of the compressed air supply will be
sufficient to make these devices fully maintenance-free.

For ØD ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item CX 7 CX 10
Max quantity of intake air at 6 bar m /h
3
12.0 28.0
Max quantity of air blown at 6 bar m3/h 17.6 36.2
Maximum level of vacuum -KPa 15 22
Final pressure abs. mbar 850 780
Maximum supply pressure bar 6 6
8 Maximum air consumption at 6 bar Nl/s 1.5 2.3
Temperature of use °C -20 / +80 -20 / +80
Noise level dB(A) 75 84
Weight g 110 104
A Ø 19 19
B Ø 32 32
C Ø 7 10
D Ø 6 6
E 15 15
F 42 42
H 33 33
L 90 90
M 13 13
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter I, to the item for a generator supplied in stainless steel (Example: CX 10 I).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.120
FLOW GENERATORS VACUUM JET CX 7 and CX 1030
14

14 30
12 Quantity of air suctioned (m3/h) at different
25
supply pressures (bar)
14
12 30
10
CX 7 25
20
30
CX 10
14
12
10 25
8 20

3D drawings are available on vuototecnica.net

m3/h m3/h

m3/h m3/h
12 15
10
8 25
6 20
15
108 10
6 20
4
m3/h

m3/h
15
8 10
46 5
m3/h

m3/h
15
10
64 5
2
0 0
1 2 3 4 5 6 10 1 2 3 4 5 6
42 5
0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6
bar 5 bar
20
0
1 2 3 4 5 6 1 2 3 4 5 6
0 bar bar
0
1 2 3 4 5 6 1 2 3 4 5 6
bar bar

20 60
Quantity of air blown (m3/h) at different supply pressures (bar)
18
20 60

16
18
20
CX 7 50
60
CX 10
50
14
16
18 40
20 60
12
14 50
16 40
18

m3/h m3/h
m3/h m3/h

10
12 30
14 50
16 40
108 30
12
14 20
86 40
m3/h
m3/h

10 30
12 20
64 10
8
m3/h
m3/h

10 30
42 20
6 10
8
20 0
4 20 1 2 3 4 5 6
6 1 2 3 4 5 6
10
0 bar 0 bar
2 1 2 3 4 5 6 1 2 3 4 5 6
4
10
bar bar
0 0
2 1 2 3 4 5 6
1 2 3 4 5 6
bar 0 bar
0
1 2 3 4 5 6 1 2 3 4 5 6
Level of vacuum (-Kpa) at different supply pressures (bar)
bar bar

16 25
CX 7 CX 10
16
14 25

20
14
16
12 25
20
12
16
14
10 25
15
20
10
14
12
-Kpa -Kpa

8
-Kpa -Kpa

15
20
86
12
10 10
15
10
648
-Kpa -Kpa

10
-Kpa -Kpa

15
5
10
4826
5
10
2
64
0 0
1 2 3 4 5 6 5 1 2 3 4 5 6
402 bar 0 bar
1 2 3 4 5 6 5 1 2 3 4 5 6
bar bar
20 0
1 2 3 4 5 6 1 2 3 4 5 6
Airbarconsumption (Nl/s) at different supply
0 pressures (bar)
bar
0
1 2 3 4 5 6 1 2 3 4 5 6 8
1,8
CX 7bar 2,5
CX bar10
1,8
1,6 2,5

1,6
1,4 2
1,8 2,5

1,4
1,2 2
1,6
1,8 2,5
1,5
1,2
1
1,4 2
1,6
Nl/s

Nl/s Nl/s

1,5
1
0,8
1,2 2
1,4
Nl/s

1
1,5
0,8
0,6
1,21 1
Nl/s

Nl/s

0,6
0,4 1,5
0,8
1 0,5
1
Nl/s

Nl/s

0,4
0,2
0,6
0,8 0,5
1
0,2
0
0,4 0
0,6 1 2 3 4 5 6 0,5 1 2 3 4 5 6
0
0,2 bar 0 bar
0,4 1 2 3 4 5 6 1 2 3 4 5 6
0,5
bar bar
0,20 0
1 2 3 4 5 6 1 2 3 4 5 6
0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6 8.121
bar bar
FLOW GENERATORS VACUUM JET CX 13 and CX 19
3D drawings are available on vuototecnica.net

For ØD ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item CX 13 CX 19
Max quantity of intake air at 6 bar m /h
3
50.0 92.0
Max quantity of air blown at 6 bar m3/h 73.7 134.0
Maximum level of vacuum -KPa 18 16
Final pressure abs. mbar 820 840
Maximum supply pressure bar 6 6
8 Maximum air consumption at 6 bar Nl/s 6.6 11.6
Temperature of use °C -20 / +80 -20 / +80
Noise level dB(A) 88 92
Weight g 280 500
A Ø 25 32
B Ø 45 54
C Ø 13 19
D Ø 8 10
E 30 43
F 55 65
H 55 82
L 140 190
M 18 22
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter I, to the item for a generator supplied in stainless steel (Example: CX 13 I).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.122
FLOW GENERATORS VACUUM JET CX 13 and CX 19
60 100

60 100 90
50
Quantity of air suctioned (m3/h) at different supply pressures (bar)
80
90
60 100
50
40
60
CX 13 70
80
90
100
CX 19
50 60
70
40 80

3D drawings are available on vuototecnica.net

90
m3/h m3/h

m3/h m3/h
30 50
60
50 70
40 80
30 40
50
60
20 70
40 30
40
m3/h

m3/h
30 50
20 60
20
30
10 40
m3/h

m3/h
30 50
20 10
20
10 30
40
0 0
10
20 1 2 3 4 5 6 20 1 2 3 4 5 6
10 30
0 bar 0 bar
1 2 3 4 5 6 10 1 2 3 4 5 6
20
10
0 bar 0 bar
10
1 2 3 4 5 6 1 2 3 4 5 6
0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6
bar bar

80 160
Quantity of air blown (m3/h) at different supply pressures (bar)
80
70 160
140

70
80
CX 13 140
160
CX 19
60 120

60
80
70
50 120
160
140
100

50
70
60
40 100
140
120
80

m3/h m3/h
m3/h m3/h

40
60
50
30 80
120
100
60

30
50
40
20 60
100
80
40
m3/h
m3/h

20
40
30
10 40
80
60
20
m3/h
m3/h

10
30
20
0 20
60
40
0
1 2 3 4 5 6 1 2 3 4 5 6
0
20
10 bar 0
40
20 bar
1 2 3 4 5 6 1 2 3 4 5 6
bar bar
10
0 20
0
1 2 3 4 5 6 1 2 3 4 5 6

0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6
bar Level of vacuum (-Kpa) at different supply pressures (bar)
bar

20 18

18
CX 13 16
CX 19
20 18

16
18
20 14
16
18
14
16
18 12
14
16
20 18
12
14
16 10
12
18 14
16
-Kpa -Kpa -Kpa -Kpa

10
-Kpa -Kpa

12
14 8
10
16 12
8 14
10
12
14 6
8
10
6
8 12
10
-Kpa -Kpa

12 4
6
4
6 8
10
8
10
2 2
4
6
4 8
6
8
0
2 0
2
4
4 1 2 3 4 5 6 6 1 2 3 4 5 6
6
0 bar 0 bar
2 2
4
4 1 2 3 4 5 6 1 2 3 4 5 6
bar bar
0 0
2
2
1 2 3 4 5 6 1 2 3 4 5 6
0 bar Air consumption (Nl/s) at different supply
0 pressures (bar)
bar
1 2 3 4 5 6 1 2 3 4 5 6 8
7
CXbar13 14
CXbar19
7 14
6 12

7
6 14
12
5 10

7 14
12
6
5 10
4 8

6 12
Nl/s Nl/s

Nl/s Nl/s

5
4 10
8
3 6

5 10
8
4
3 6
2 4
Nl/s

Nl/s

4 8
6
3
2 4
1 2
Nl/s

Nl/s

3 6
4
2
1 2
0 0
1 2 3 4 5 6 1 2 3 4 5 6
2 4
2
1
0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6
1 bar 2 bar
0 0
1 2 3 4 5 6 1 2 3 4 5 6
0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6 8.123
bar bar
FLOW GENERATORS VACUUM JET CX 25, CX 38 and CX 50
3D drawings are available on vuototecnica.net

For ØD ext. hose

P=COMPRESSED AIR CONNECTION R=EXHAUST U=VACUUM CONNECTION

Item CX 25 CX 38 CX 50
Max quantity of intake air at 6 bar m /h
3
150 310 405
Max quantity of air blown at 6 bar m3/h 210 400 525
Maximum level of vacuum -KPa 13 10 8
Final pressure abs. mbar 870 900 920
Maximum supply pressure bar 6.0 6.0 6.0
8 Maximum air consumption at 6 bar Nl/s 16.6 25.0 33.3
Temperature of use °C -20 / +80 -20 / +80 -20 / +80
Noise level dB(A) 100 103 103
Weight g 560 800 1090
A Ø 38 51 64
B Ø 60 75 90
C Ø 25 38 50
D Ø 10 12 16
E 42 42 42
F 66 66 66
H 82 82 82
L 190 190 190
M 22 22 22
Note: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Add the letter I, to the item for a generator supplied in stainless steel (Example: CX 38 I).
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.124
FLOW GENERATORS VACUUM JET CX 25, CX 38 and CX 50
Quantity of air suctioned (m3/h) at different supply pressures (bar)

160
CX 25 350
CX 38 450
CX 50

3D drawings are available on vuototecnica.net

160 350 450
160
140 350 400
450
300
140 400
300 350
400
160
140
120 350 450
300
250 350
120 300
350
140
120 250 400
100 300
250 300
200 250
100 300
350
120

/h3/hm3/h

/h3/hm3/h
/h3/hm3/h

100
80 200
250 250
200 200
250
80 150 300
m3/h m3m

m3/h m3m

m3/h m3m
100
80
60 200
150
200 150
200
250
60 150
100
80
60
40 150
100 100
150
200
40 150
100
60
40 50 100
20 50
100
150
50
20 100 50
40 50
20
0 0 0
50
100
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
0 0 0
50
20
0 1 2 3 bar 4 5 6 0 1 2 3 bar 4 5 6 0
50 1 2 3 bar 4 5 6
1 2 3 bar 4 5 6 1 2 3 bar 4 5 6 1 2 3 bar 4 5 6
0 bar 0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
bar Quantity of air blown (m3/h) at
bardifferent supply pressures (bar) bar

250
250
CX 25 450
450
CX 38 600
600
CX 50
250 400
450 600
400 500
200
250 350
400
450 500
600
200 500
350
200 300 400
350
400
150 300 400
500
200 250
300 400
150 350
/h3/hm3/h

/h3/hm3/h
/h3/hm3/h

150 250 300

200
250
300 300
400
100
m3/h m3m

m3/h m3m

m3/h m3m
200 300
150
100 150
200
250 200
100
150 200
300
100
150
200 200
50
100 100 100
50 50
100
150 100
200
50
50 100
0 0
50
100 0
50 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
0 0 0
100
0 1 2 3 bar 4 5 6 0
50 1 2 3 bar 4 5 6 0 1 2 3 bar 4 5 6
1 2 3 bar 4 5 6 1 2 3 bar 4 5 6 1 2 3 bar 4 5 6
0 bar 0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
bar bar bar

Level of vacuum (-Kpa) at different supply pressures (bar)

14 12 9
14 CX 25 12 CX 38 9
8
CX 50
14 12 9
12
10 8
12 7
8
14 10
12 9
12
10 10 7
8 6
7
8
10
12
10 8
10 6
8 5
8 6
7
-Kpa-Kpa

-Kpa-Kpa

8 6 5
10
8 4
5
6 6
8 6
-Kpa -Kpa

-Kpa -Kpa

6 4
6
8 4 3
4
5
6
4
4
6 3
4 4 2
3
4
6
4 2 2
2
2
4 1
2
3
2
4 2 1
2
0 0 0
1
2
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
0 0
2 0
2
0 1 2 3 bar 4 5 6 0 1 2 3 bar 4 5 6 0
1 1 2 3 bar 4 5 6
1 2 3 bar 4 5 6 1 2 3 bar 4 5 6 1 2 3 bar 4 5 6
0 bar 0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
bar bar bar

Air consumption (Nl/s) at different supply pressures (bar)

18 30 35 8
18 30 35
16
CX 25 CX 38 CX 50
18 30 35
30
16 25
14
16 30
18 25
30 35
30
14 25 25
12
14 20
16 25
30
12 20
25 25
10 20
12
14 20
Nl/sNl/s

Nl/sNl/s
Nl/s Nl/s

10 15 20
25
8
10 20
12 15
20 15
Nl/s

Nl/s
Nl/s

8 15
15
6
8 10 20
10 15
10
Nl/s

Nl/s
Nl/s

6 10
15
4
6 10 10
8 15
4 5 10
5
2
4 5
10
6
5
2 5 10
5
0
2 0 0
4
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
0 0
5 0
5
0
2 1 2 3 bar 4 5 6 0 1 2 3 bar 4 5 6 0 1 2 3 bar 4 5 6
1 2 3 bar 4 5 6 1 2 3 bar 4 5 6 1 2 3 bar 4 5 6
0 bar 0 bar 0 bar
1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6
bar bar bar

8.125
MINI PNEUMATIC PUMP SETS DOP 06 and DOP 10

Mini pneumatic pump sets are small independent vacuum-producing units, exclusively
supplied with compressed air, with reduced size.
They are composed of:
- A small welded sheet steel tank
3D drawings are available on vuototecnica.net

- A shut off valve to intercept compressed air

- A pressure regulator with filter and pressure gauge
- A compressed air vacuum generator
- A pneumatic drive valve for supplying the vacuum generator
operated by the vacuum switch
- A pneumatic vacuum switch for adjusting the level of vacuum
- A vacuum gauge for reading the level of vacuum
- A manual valve for vacuum interception
- A suction filter with FC series paper cartridge
- A cock for condensation drainage from the tank
The level of vacuum, preset via the mini vacuum switch is
automatically maintained in the tank.
Mini pneumatic pump sets are suited for equipping fixed or
mobile working units that require vacuum, such as:
- Trolleys with vacuum cups for fixing and transporting glass
and crystals.
- Vacuum clamping systems for ski maintenance, marble drilling and processing, for
polishing objects in pewter, copper, silver, etc.
- Hoists with vacuum cups for lifting television sets and household appliances in general,
for glass installation in door and window frames, for feeding sheet metal into presses, etc.
The mini pneumatic pump sets do not require any electrical current but only compressed
air at 4-6 bar pressure. Recommended in working environments where ignition sources
could cause a fire hazard.

Coaxial servo-controlled ball supply valve

Regulator filter Vacuum switch item 12 02 30 Vacuum interception valve

item 13 02 11

Vacuum gauge item 09 05 10

Filter FC10

Generator
For Ø8 ext. hose

Cock for
condensation
discharge item 13 02 11

Tank Generator Pneumatic C D E F G H L Weight

Item switchgear
Litres item item Ø Kg
DOP 06 PVP 12 MX 6 PVP 12 MX DOP 20 90 60 G3/8” 150 95 180 270 620 12.7
DOP 06 PVP 25 MX 6 PVP 25 MX DOP 20 90 60 G3/8” 150 95 180 270 620 13.0

DOP 10 PVP 12 MX 10 PVP 12 MX DOP 20 90 100 G3/8” 210 95 240 310 620 12.9
DOP 10 PVP 25 MX 10 PVP 25 MX DOP 20 90 100 G3/8” 210 95 240 310 620 13.2
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.126
MINI PNEUMATIC PUMP SETS DOP 20

This mini pump set is set apart from the previously ones for the vacuum generator
installed, as well as for the tank volume.
Vacuum generators of the series PVP… MDX ES are in fact equipped with an energy
saving device which automatically maintains the preset level of vacuum inside the tank.

3D drawings are available on vuototecnica.net

The other accessories installed, except the vacuum switch and the pneumatically driven
valve for vacuum generator supply, are the same installed on DOP 06 and DOP 10. Their
intended use is the same as the previously described mini pneumatic pump sets.

Vacuum gauge item 09 05 10 Coaxial servo-controlled ball supply valve Vacuum interception valve
For Ø8 ext. hose

item 13 03 11
Regulator filter Pressure gauge item 09 03 25

Vacuum gauge item 09 03 15 Filter FC 20

Generator

Cock for condensation discharge item 13 03 11

Tank Generator Pneumatic D E F G H L Weight

Item switchgear
Litres item item Ø Kg
DOP 20 PVP 25 MDX 20 PVP 25 MDX ES DOP 20 90 G1/2” 225 135 270 340 1110 20.6
DOP 20 PVP 35 MDX 20 PVP 35 MDX ES DOP 20 90 G1/2” 225 135 270 340 1110 20.7
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.127
PNEUMATIC PUMP SETS 25, DOP 50 and DOP 100

Pneumatic pump sets are self-contained vacuum production units, fed exclusively by
compressed air.
They are composed of:
- A welded sheet steel tank
3D drawings are available on vuototecnica.net

- A compressed air vacuum generator of the series PVP … MDX ES, equipped
with an energy saving device
- A vacuum gauge for reading the level of vacuum
- A manual valve for vacuum interception
- A suction filter with FC series paper cartridge
- A pressure regulator with filter and pressure gauge
- A shut off valve to intercept compressed air
- A cock for condensation drainage from the tank
The level of vacuum in the tank, previously set with the vacuum switch in
the generator, is automatically maintained. The pneumatic pump sets are
normally used to handle particularly heavy or valuable loads, as it allows
vacuum cups to maintain grip for a certain period of time (varies according
to tank capacity) even during unexpected absence of power. These pump sets
are recommended for multi-point applications, to centralise vacuum.
In both cases, use of the pump set is especially advantageous under the profile of
energy savings as the generator only operates when a vacuum is required by the
utility machine.
The pneumatic pump sets do not require any electrical current but only compressed
air at 4-6 bar pressure. Recommended in working environments where ignition sources
could cause a fire hazard.

Coaxial servo-controlled ball supply valve

Regulator filter Pressure gauge item 09 03 25

Vacuum gauge item 09 03 15

Vacuum gauge item 09 05 10

For Ø8 ext. hose

Vacuum
interception valve
Filter FC 20 Generator

Cock for condensation

discharge item 13 03 11
8

Tank Generator Pneumatic H L M N R Weight

Item switchgear
Litres item item Ø Ø Kg
DOP 25 PVP 25 MDX 25 PVP 25 MDX ES DOP 20 90 225 185 240 51 G1/2” 15.9
DOP 25 PVP 35 MDX 25 PVP 35 MDX ES DOP 20 90 225 185 240 51 G1/2” 16.0
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.128
PNEUMATIC PUMP SETS DOP 50

3D drawings are available on vuototecnica.net

Coaxial servo-controlled ball supply valve

Regulator filter Pressure gauge item 09 03 25

Vacuum gauge item 09 03 15

Vacuum gauge item 09 05 10

For Ø8 ext. hose

Vacuum
interception valve
Generator
Filter FC 20

Cock for condensation

discharge item 13 03 11
8

Tank Generator Pneumatic H L M N R Ø ext. Weight

Item switchgear tube
Litres item item Ø Ø Ø Kg
DOP 50 PVP 50 MDX 50 PVP 50 MDX ES DOP 20 90 245 205 280 51 G1/2” 8 18.9
DOP 50 PVP 60 MDX 50 PVP 60 MDX ES DOP 50 90 245 205 280 51 G1/2” 12 19.7
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.129
PNEUMATIC PUMP SETS DOP 100
3D drawings are available on vuototecnica.net

Coaxial servo-controlled ball supply valve

Regulator filter Pressure gauge item 09 03 25

Vacuum gauge item 09 03 15

Vacuum gauge item 09 05 10

For Ø12 ext. hose

Vacuum
interception valve
Generator
Filter FC 30

8 Cock for condensation

discharge item 13 03 11

Tank Generator Pneumatic H L M N R Weight

Item switchgear
Litres item item Ø Ø Kg
DOP 100 PVP 75 MDX 100 PVP 75 MDX ES DOP 50 90 300 255 350 41 G1” 31.0
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.130
PNEUMATIC PUMP SETS DOP 150 and DOP 300

Pneumatic pump sets are self-contained vacuum production units, fed

exclusively by compressed air.
They are composed of:
- A welded sheet steel tank

3D drawings are available on vuototecnica.net

- A compressed air vacuum generator of the series PVP ... MDR ES,
equipped with energy saving device
- A vacuum gauge for a direct reading of the level of vacuum in the tank
- A manual valve for vacuum interception
- A suction filter with FC series paper cartridge
- A pressure regulator with filter
- A shut off valve to intercept compressed air
- A cock for condensation drainage from the tank
The level of vacuum in the tank, previously set with the vacuum
switch integrated in the pneumatic coaxial shutter supply valve, is
fully automatically. The pneumatic pump sets are normally used
to handle particularly heavy or valuable loads, as it allows vacuum
cups to maintain grip for a certain period of time (varies according to
tank capacity) even during unexpected absence of power. They are
also recommended for centralising vacuums, for powering multiple
utility machines. In both cases, use of the pump set is especially
advantageous under the profile of energy savings as the generator only
operates when a vacuum is required by the utility machine.
The pneumatic pump sets do not require any electrical energy but
only compressed air at 4-6 bar pressure. Recommended in working
environments where ignition sources could cause a fire hazard.

Vacuum gauge item 09 05 10

Regulator filter Coaxial servo-controlled ball supply valve

Generator
For Ø15 ext. hose

Vacuum
interception valve
Filter FC 38

Cock for condensation 8

discharge item 13 03 11

Tank Generator Pneumatic H L M N R Weight

Item switchgear
Litres item item Ø Ø Kg
DOP 150 PVP 150 MD 150 PVP 150 MDR ES DOP 150 90 360 280 400 41 G1”1/2 40.2
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.131
PNEUMATIC PUMP SETS DOP 300
3D drawings are available on vuototecnica.net

Vacuum gauge item 09 05 10

Regulator filter Coaxial servo-controlled ball supply valve

Generator
For Ø15 ext. hose

Vacuum
interception valve
Filter FC 55

8 Cock for condensation

discharge item 13 03 11

Tank Generator Pneumatic H L M N R Weight

Item switchgear
Litres item item Ø Ø Kg
DOP 300 PVP 300 MD 300 PVP 300 MDR ES DOP 150 90 440 340 500 45 G2” 41.2
Note: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.132
PNEUMATIC DEVICES FOR THE POWER SUPPLY OF MINI PNEUMATIC PUMP SETS
DOP 06, DOP 10, DOP 20 AND PUMP SETS DOP 25, DOP 50, DOP 100, DOP 150 and DOP 300
The pneumatic equipment of the mini pump sets and pump sets is sized so as to
guarantee the right amount of compressed air supply to the vacuum generators installed
on them, at a correct, constant and continuous pressure.
It is composed of:

3D drawings are available on vuototecnica.net

- A pressure regulator with filter and pressure gauge for regulating compressed supply air
- A metal bracket for fixing the pressure regulator to the support
- A slide valve to intercept compressed air
- Two quick couplings to connect the air supply line and the vacuum generator
They are available in different sizes depending on the vacuum generator installed on the
mini pump set or on the pump set.

PNEUMATIC DEVICES FOR THE POWER SUPPLY OF MINI PNEUMATIC PUMP SETS DOP
06, DOP 10 and DOP 20
For Ø8 ext. hose

For Ø8 ext. hose

Weight Suitable for generator

Item
Kg item
DOP 20 90 0.36 PVP 12 MX - PVP 25 MX - PVP 25 MDX ES - PVP 35 MDX ES - PVP 50 MDX ES

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.133
PNEUMATIC DEVICES FOR THE POWER SUPPLY OF PNEUMATIC PUMP SETS DOP 25,
DOP 50 and DOP 100
3D drawings are available on vuototecnica.net

For Ø12 ext. hose

Weight Suitable for generator

Item
Kg item
DOP 50 90 0.72 PVP 60 MDX ES - PVP 75 MDX ES

PNEUMATIC DEVICES FOR THE POWER SUPPLY OF PNEUMATIC PUMP SETS DOP 150
and DOP 300
For Ø15 ext. hose

For Ø15 ext. hose

Weight Suitable for generator

Item
Kg item
DOP 150 90 1.2 PVP 150 MDR - PVP 300 MDR

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
8.134
SPECIAL PRODUCTS FOR VACUUM GENERATORS

3D drawings are available on vuototecnica.net

3MSVE

PVP 750 MDV - COS1

8.135
OCTOPUS VACUUM GRIPPING SYSTEMS

OCTOPUS VACUUM GRIPPING SYSTEM - GENERAL DESCRIPTION PG. 9.00 ÷ 9.01

OCTOPUS GRIPPING SYSTEM COMPOSITION PG. 9.02 ÷ 9.03

3D drawings are available on vuototecnica.net

OCTOPUS GRIPPING SYSTEM item SO 15 20 MX PG. 9.04
OCTOPUS GRIPPING SYSTEM item SO 20 30 X, SO 20 40 X and SO 20 60 X PG. 9.05
OCTOPUS GRIPPING SYSTEM item SO 30 30 X, SO 30 40 X, SO 30 50 X, SO 40 40 X and SO 40 60 X PG. 9.06
OCTOPUS GRIPPING SYSTEM item SO 40 100 X, SO 60 80 X, SO 60 120 X and SO 80 100 X PG. 9.07
SMALL OCTOPUS VACUUM GRIPPING SYSTEMS item SO DO 10 X, SO 08 08 X and SO O7 120 X PG. 9.08
ROUND OCTOPUS GRIPPING SYSTEM item SO DO 35 X and SO DO 50 X PG. 9.09
STANDARD SUCTION PLATES PX and P2X FOR OCTOPUS SYSTEMS PG. 9.10
STANDARD SUCTION PLATES WITH SHUT-OFF VALVES PXE and P2XE FOR OCTOPUS SYSTEMS PG. 9.11
SPECIAL SUCTION PLATES PY and P2Y FOR OCTOPUS SYSTEMS PG. 9.12
SPECIAL SUCTION PLATES WITH SHUT-OFF VALVES PY2E and P2Y2E FOR OCTOPUS SYSTEMS PG. 9.13
SPECIAL SUCTION PLATES PZ and P2Z FOR OCTOPUS SYSTEMS PG. 9.14
VACUUM CUP SUCTION PLATES PV FOR OCTOPUS SYSTEMS PG. 9.15
VACUUM CUP SUCTION PLATES PV2 FOR OCTOPUS SYSTEMS PG. 9.16
VACUUM CUP SUCTION PLATES WITH SHUT-OFF VALVES PVE FOR OCTOPUS SYSTEMS PG. 9.17
VACUUM CUP SUCTION PLATES WITH SHUT-OFF VALVES P2V2E FOR OCTOPUS SYSTEMS PG. 9.18
BAG GRIPPING SUCTION PLATES PJ FOR OCTOPUS SYSTEMS PG. 9.19
OCTOPUS GRIPPING BARS - GENERAL DESCRIPTION PG. 9.20 ÷ 9.21
OCTOPUS GRIPPING BARS item BO O8 60 X, BO O8 80 X and BO O8 100 X PG. 9.22
OCTOPUS GRIPPING BARS item BO 12 40 X, BO 12 60 X and BO 12 80 X PG. 9.23
OCTOPUS GRIPPING BARS item BO 12 100 X, BO 08 120 X, BO 12 120 X and BO 12 140 X PG. 9.24
STANDARD SUCTION PLATES PX and P2X FOR OCTOPUS GRIPPING BARS PG. 9.25
VACUUM CUP SUCTION PLATES PV FOR OCTOPUS GRIPPING BARS PG. 9.26
SUCTION PLATES WITH SHUT-OFF VALVES PXE and P2XE FOR OCTOPUS GRIPPING BARS PG. 9.27
VACUUM CUP SUCTION PLATES WITH SHUT-OFF VALVES PVE FOR OCTOPUS GRIPPING BARS PG. 9.28
LOCKING PLATES FOR OCTOPUS GRIPPING BARS PG. 9.29 ÷ 9.30
FLANGE FIXING SUPPORT FOR OCTOPUS SYSTEMS WITHOUT VACUUM GENERATOR PG. 9.31
ACCESSORIES AND SPARE PARTS FOR OCTOPUS GRIPPING SYSTEMS AND BARS PG. 9.32 ÷ 9.34
SPECIAL OCTOPUS GRIPPING SYSTEM PRODUCTS PG. 9.35 ÷ 9.37
SPECIAL OCTOPUS GRIPPING SYSTEM PRODUCTS WITH 3D PRINTER PG. 9.38
OCTOPUS VACUUM GRIPPING SYSTEM QUESTIONNAIRE PG. 9.39 ÷ 9.42

9
OCTOPUS VACUUM GRIPPING SYSTEM - GENERAL DESCRIPTION

The OCTOPUS system is our answer to the ever increasing

requirements of operational flexibility for palletising robots and
SPECIAL SOLUTIONS FOR ALL SECTORS
vacuum gripping systems in general. WITH OCTOPUS VACUUM GRIPPING SYSTEMS
In fact, this system allows gripping objects of any shape and nature,
3D drawings are available on vuototecnica.net

provided that they do not have an excessive transpiration, without

having to place or change vacuum cups, and even when their surface
occupies only 5% of the entire suction plate. The maximum weight
of the load to be lifted will obviously be proportional to the gripping
surface.
Standard OCTOPUS systems are composed of:
- One or two compressed air-fed vacuum generator as shown in the CERAMICS PACKAGING
picture and in the drawing, that has to be ordered separately, since it
is not included in the code, with the exception of item SO 15 20 MX.
- An anodised aluminium box, open on one side, with a built-in
micro-fine mesh filter in stainless steel that protects the vacuum
generator and is very easy to inspect. On the top outside of the box
there are one or more connections for possible installation of control
devices or solenoid valves for prompt restoration of the atmospheric
pressure on its inside.
MARBLE PLASTIC
- A suction plate sealing the box, also made with anodised aluminium,
with calibrated holes equidistant from each other and coated
with a special perforated foam rubber. This suction plate can thus
perfectly adapt to any gripping surface, whether it be smooth, rough
or irregular. With the same system, for instance, it is possible to grip
and handle cardboard boxes and the wooden pallet that supports it.
These OCTOPUS systems are also available upon request in
dimensions and with vacuum tables and vacuum generators other
than those indicated in the tables. FOOD PHARMACEUTICALS

WOOD CONSTRUCTION

PALLETS GLASS

CAN

9
TECHNIQUES USED FOR THE CREATION OF OCTOPUS SUCTION PLATES:

3D drawings are available on vuototecnica.net

CALIBRATED
HOLE

WITH CALIBRATED HOLES WITH SHUT-OFF VALVES

The calibrated holes drilled onto the aluminium suction plates, based Shut-off valves, when properly calibrated, allow a certain quantity of
on their number and cross-section, allows for the selection of the fluid to go through; afterwards, if the fluid continues to go through,
exact flow rate of the vacuum generator to be used: in fact, when the they automatically close.
vacuum differential is reached with all calibrated holes of the open When applied on the section plates, without a load to be gripped or in
suction plate on the OCTOPUS system is 0 mbar, this means that the presence of a defective grip on foam rubber, they automatically
the flow rate of the vacuum generator used is correct, but due to the close suction, thus preventing the level of vacuum from lowering on
operating principle of the OCTOPUS systems, it will be necessary to the remaining holes or vacuum cups that are regularly being gripped.
increase it to obtain a vacuum differential greater than 0 mbar. This feature reduces the vacuum generator flow rate compared
It will therefore be necessary to use a generator with a higher flow to standard OCTOPUS systems, to the benefit of energy savings.
rate to obtain a vacuum differential greater than the greater the flow Moreover, the particular shape of our shut-off valves allows the use of
rate of the generator used. In this way, it is possible to determine the gripping surfaces in any position.
which percentage of the surface of the load to be gripped can remain
uncovered during the gripping phase, in compliance with the safety
parameters.
This technique requires a greater expenditure of energy with respect
to the use of shut-off valves.

9.01
OCTOPUS GRIPPING SYSTEM COMPOSITION AND
RELATIVE IDENTIFICATION CODES
The OCTOPUS systems described on the following pages are equipped as standard with PX suction plates.
Should you want to replace these plates with others with different features you will have to modify the
identification codes as described in this page.
3D drawings are available on vuototecnica.net

Example of a standard OCTOPUS system composition with a gripping plane of 300x400 mm:

Vacuum generator item PVP 150 MD PO

(to be ordered separately)

OCTOPUS system body item SO 30 40

15
With suction plate PX item SO 30 40 X
With suction plate P2X item SO 30 40 2X

15
With suction plate PX and shut-off valves item SO 30 40 XE
With suction plate P2X and shut-off valves item SO 30 40 2XE

20
With suction plate PH item SO 30 40 H
With suction plate P2H item SO 30 40 2H

15
With suction plate PY item SO 30 40 Y
With suction plate P2Y item SO 30 40 2Y

9 30

15
With suction plate PY and shut-off valves item SO 30 40 Y2E
With suction plate P2Y and shut-off valves item SO 30 40 2Y2E

9.02
OCTOPUS GRIPPING SYSTEM COMPOSITION AND
RELATIVE IDENTIFICATION CODES

3D drawings are available on vuototecnica.net

15
With suction plate PZ item SO 30 40 Z
With suction plate P2Z item SO 30 40 2Z

With suction plate PV item SO 30 40 V

(1/8” vacuum cup supports, vacuum cups not included)
With suction plate PV and shut-off valves item SO 30 40 VE
(1/8” vacuum cup supports, vacuum cups not included)

With suction plate P2V item SO 30 40 2V

(1/4” vacuum cup supports, vacuum cups not included)
With suction plate P2V and shut-off valves item SO 30 40 2V2E
(1/4” vacuum cup supports, vacuum cups not included)

With suction plate PJ item SO 30 40 J

Example of an order for an OCTOPUS system with suction plate P2Y, complete with vacuum generator:
1 PVP 150 MD PO
1 SO 30 40 2Y

Example of an order for an OCTOPUS system with suction plate P2V, complete with silicone vacuum cups vacuum generator:
1 PVP 150 MD PO
1 SO 30 40 2V
36 01 40 42 S

Example of an order for an OCTOPUS system with suction plate PX and shut-off valves, complete with vacuum generator:
1 PVP 150 MD PO
1 SO 30 40 XE

VACUUM GENERATORS USED ON OCTOPUS SYSTEMS 9

Although not an included part, the standard OCTOPUS gripping system generators indicated in the tables have been selected after careful
evaluation of the best ratio achieved between performance and consumption of compressed air. Contact our technical department before
replacing them with others having different characteristics.

FASTENING AND CONNECTION ALTERNATIVES

It is possible to connect the OCTOPUS system to a remote installed vacuum generator or to an alternative vacuum source, by fixing one of the
special flange supports shown and described on the following pages instead of the generator.

9.03
OCTOPUS VACUUM GRIPPING SYSTEM
3D drawings are available on vuototecnica.net

Vacuum Vacuum Air inlet

generator gauge connection G1/4”

Compressed
air connection

Item SO 15 20 MX
Suction plate item PX 15 20
Gripping force Kg 21.2
Vacuum generator item N°1 PVP 25 MX PO
Maximum supply pressure bar 6
9 Maximum level of vacuum -KPa 90
Air consumption at 6 bar Nl/s 3.2
Intake air flow rate m3/h 31.0
Temperature of use °C -20 / +80
Weight Kg 2.1
P Connection for compressed air tube Ø ext. 8
R Exhaust connection Ø N° 4 x G1/4”
NOTE: The vacuum generator indicated in the table are included with the OCTOPUS system
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.04
OCTOPUS VACUUM GRIPPING SYSTEM

3D drawings are available on vuototecnica.net

Vacuum Vacuum Pressure
generator gauge gauge

Air inlet Compressed

connection G1/2” air connection

Item SO 20 30 X SO 20 40 X SO 20 60 X
Suction plate item PX 20 30 PX 20 40 PX 20 60
Gripping force Kg 42.4 56.6 84.8
Fitted for vacuum generator item N°1 PVP 100 M PO N°1 PVP 140 M PO N°1 PVP 200 M PO
Maximum supply pressure bar 6 6 6
Maximum level of vacuum -KPa 90 90 90
Air consumption at 6 bar Nl/s 9.8 13.0 19.4
Intake air flow rate m3/h 108.0 152.0 200.0
Temperature of use °C -20 / +80 -20 / +80 -20 / +80
Weight Kg 7.0 8.6 10.7 9
A 300 400 600
E 74 96 96
F 20 70 170
G 16 66 166
H 124 146 146
P Connection for compressed air tube Ø ext. 15 15 15
NOTE: The code SO .. .. X only identifies the OCTOPUS system body with relative suction plate PX.
The vacuum generator indicated in the table is not included with the OCTOPUS system and therefore must be ordered separately with its own code.
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.05
OCTOPUS VACUUM GRIPPING SYSTEM
3D drawings are available on vuototecnica.net

Pressure Vacuum Air inlet Vacuum

gauge gauge connection G1/2” generator

Compressed
air connection

Item SO 30 30 X SO 30 40 X SO 30 50 X SO 40 40 X SO 40 60 X
Suction plate item PX 30 30 PX 30 40 PX 30 50 PX 40 40 PX 40 60
Gripping force Kg 63.6 84.8 106.0 113.1 169.6
Fitted for vacuum generator item N°1 PVP 150 MD PO N°1 PVP 150 MD PO N°1 PVP 300 MD PO N°1 PVP 300 MD PO N°1 PVP 300 MD PO
Maximum supply pressure bar 6 6 6 6 6
Maximum level of vacuum -KPa 90 90 90 90 90
Air consumption at 6 bar Nl/s 16.0 16.0 32.0 32.0 32.0
Intake air flow rate m3/h 200.0 200.0 400.0 400.0 400.0
Temperature of use °C -20 / +80 -20 / +80 -20 / +80 -20 / +80 -20 / +80
Weight Kg 11.5 12.5 15.0 17.0 19.0
9 A 300 400 500 400 400
B 300 300 300 400 600
C 138 138 158 158 158
E 88 88 108 108 108
F 50 100 150 100 200
G 15 15 15 65 65
P Connection for compressed air tube Ø ext. 15 15 15 15 15
NOTE: The code SO .. .. X only identifies the OCTOPUS system body with relative suction plate PX.
The vacuum generator indicated in the table is not included with the OCTOPUS system and therefore must be ordered separately with its own code.
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.06
OCTOPUS VACUUM GRIPPING SYSTEM

The standard OCTOPUS systems represented on this page differ from

those previously described by their larger dimensions and the number
of vacuum generators that compose them. More precisely:
- Two compressed air-fed vacuum generator as shown in the picture

3D drawings are available on vuototecnica.net

and in the drawing, that have to be ordered separately, since it is not
included in the item code.
- An anodised aluminium box, open on one side, with a built-in
micro-fine mesh filter in stainless steel that protects the vacuum
generator and is very easy to inspect. On the top outside of the box
there are one or more connections for possible installation of control
devices or solenoid valves for prompt restoration of the atmospheric
pressure on its inside.
- A suction plate sealing the box, also made with anodised aluminium,
with calibrated holes equidistant from each other and coated
with a special perforated foam rubber. This suction plate can thus
perfectly adapt to any gripping surface, whether it be smooth, rough
or irregular. With the same system, for instance, it is possible to grip
and handle tomato jars, paint cans, ceramic tiles, cardboard boxes,
etc. and the wooden pallet that supports them.
These OCTOPUS systems are also available upon request in
dimensions and with vacuum tables and vacuum generators other
than those indicated in the table.

Pressure Vacuum
gauge gauge

Air inlet Compressed Vacuum Compressed

connection G1/2” air connection generators air connection

Item SO 40 100 X SO 60 80 X SO 60 120 X SO 80 100 X

Suction plate item PX 40 100 PX 60 80 PX 60 120 PX 80 100
Gripping force Kg 282.6 339.2 508.7 597.4
Fitted for vacuum generators item N°2 PVP 300 MD PO N°2 PVP 300 MD PO N°2 PVP 450 MD PO N°2 PVP 450 MD PO
Maximum supply pressure bar 6 6 6 6
Maximum level of vacuum -KPa 90 90 90 90
Air consumption at 6 bar Nl/s 64.0 64.0 95.6 95.6
Intake air flow rate m3/h 800.0 800.0 1160 1160
Temperature of use °C -20 / +80 -20 / +80 -20 / +80 -20 / +80
Weight Kg 34.0 37.5 50.0 53.5
A 400 600 600 800
B 1000 800 1200 1000 9
C 120 70 170 120
F 100 200 200 300
G 108 108 130 130
H 158 158 180 180
L 220 120 320 220
P Connection for compressed air tube Ø ext. 15 15 22 22
NOTE: The code SO .. .. X only identifies the OCTOPUS system body with relative suction plate PX.
The vacuum generators indicated in the table are not included with the OCTOPUS system and therefore must be ordered separately with its own code.
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.07
SMALL OCTOPUS VACUUM GRIPPING SYSTEMS
3D drawings are available on vuototecnica.net

air connection

air connection
Compressed

Compressed

Vacuum
generator

Vacuum Vacuum
generator generator

Item SO DO 10 X SO 08 08 X SO 07 12 X
Suction plate item PX DO 10 PX 08 08 PX 07 12
Gripping force Kg 4 3 4
9 Vacuum generator item M14PO M14PO M14PO
Maximum supply pressure bar 5 5 5
Maximum level of vacuum -KPa 85 85 85
Air consumption at 6 bar Nl/s 2.5 2.5 2.5
Intake air flow rate m3/h 12.6 12.6 12.6
Temperature of use °C -20 / +80 -20 / +80 -20 / +80
Weight Kg 0.5 0.4 0.7
P Connection for compressed air tube Ø ext. 6 6 6
NOTE: The vacuum generator indicated in the table is included with the OCTOPUS system.
NOTE:
All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.08
ROUND OCTOPUS VACUUM GRIPPING SYSTEM

3D drawings are available on vuototecnica.net

Air inlet
connection G1/2”

Vacuum
gauge

Pressure
gauge

Vacuum
generator

Compressed
air connection

Item SO DO 35 X SO DO 50 X
Suction plate item PX DO 35 PX DO 50
Gripping force Kg 65.4 139.6
Fitted for vacuum generator item N°1 PVP 170 M PO N°1 PVP 300 MD PO
Maximum supply pressure bar 6 6
Maximum level of vacuum -KPa 90 90
Air consumption at 6 bar Nl/s 16.3 32.0
Intake air flow rate m3/h 182.0 400.0
Temperature of use °C -20 / +80 -20 / +80
Weight Kg 9.5 17.0
A 120 270
B 264 200 9
C 43 150
D Ø 350 500
E 96 108
H 146 158
I 8.5 10.5
P Connection for compressed air tube Ø ext. 15 15
NOTE: The code SO DO . X only identifies the OCTOPUS system body with relative suction plate PX.
The vacuum generator indicated in the table is not included with the OCTOPUS system and therefore must be ordered separately with its own code.
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.09
STANDARD SUCTION PLATES PX and P2X FOR OCTOPUS SYSTEMS

The suction plates PX described on this page are installed as standard on all OCTOPUS systems and,
therefore, can be supplied as a spare or replacement part.
They are made with anodised aluminium sheets with calibrated holes equidistant from each other and
coated with a special perforated foam rubber with two different thicknesses: 15 mm for suction plates
3D drawings are available on vuototecnica.net

of the PX range; 30 mm, for special suction plates of the P2X range. The foam rubber is also perforated
at the calibrated holes, but its holes have a diameter of 10-15 mm. The use of calibrated holes allows for
exact calculation of the flow rate of the vacuum generator to be used, to ensure that, even in the presence
of losses due to transpiration or even in case of failure to cover the object to be gripped, a minimum
sufficient level of vacuum remains for gripping and handling the load.
Their lifting force was calculated considering a level of vacuum of at least -75 Kpa, the total surface of the
holes within the foam rubber and a factor of safety 3.

Force A B C D E F H I Holes Only rubber Weight

Item
Kg Ø Ø No. item Kg
PX 07 12 4.5 70 120 10 --- 5 15 20 17 24 X 07 12 0.13
PX 08 08 3.0 80 80 10 --- 5 15 20 17 16 X 08 08 0.12
PX 15 20 21.2 150 200 15 --- 5 15 20 24 48 X 15 20 0.40
PX 20 30 42.4 200 300 15 --- 5 15 20 24 96 X 20 30 0.80
PX 20 40 56.6 200 400 15 --- 5 15 20 24 128 X 20 40 1.10
PX 20 60 84.8 200 600 15 --- 5 15 20 24 192 X 20 60 1.70
PX 30 30 63.6 300 300 15 --- 5 15 20 24 144 X 30 30 1.30
PX 30 40 84.8 300 400 15 --- 5 15 20 24 192 X 30 40 1.70
PX 30 50 106.0 300 500 15 --- 5 15 20 24 240 X 30 50 2.10
PX 40 40 113.1 400 400 15 --- 5 15 20 24 256 X 40 40 2.20
PX 40 60 169.6 400 600 15 --- 5 15 20 24 384 X 40 60 3.40
PX 40 100 282.6 400 1000 15 --- 5 15 20 24 656 X 40 100 5.60
PX 60 80 339.2 600 800 15 --- 5 15 20 24 768 X 60 80 6.70
PX 60 120 508.7 600 1200 15 --- 5 15 20 24 1176 X 60 120 10.10
PX 80 100 597.4 800 1000 15 --- 5 15 20 24 1353 X 80 100 11.30
PX DO 10 9.0 --- --- 15 100 5 15 20 24 21 X DO 10 0.12
PX DO 35 65.4 --- --- 15 350 5 15 20 24 148 X DO 35 1.30
PX DO 50 139.6 --- --- 15 500 5 15 20 24 316 X DO 50 2.30

P2X 07 12 4.5 70 120 10 --- 5 30 35 17 24 2X 07 12 0.26

P2X 08 08 3.0 80 80 10 --- 5 30 35 17 16 2X 08 08 0.24
P2X 15 20 21.2 150 200 15 --- 5 30 35 24 48 2X 15 20 0.44
P2X 20 30 42.4 200 300 15 --- 5 30 35 24 96 2X 20 30 0.89
P2X 20 40 56.6 200 400 15 --- 5 30 35 24 128 2X 20 40 1.21
P2X 20 60 84.8 200 600 15 --- 5 30 35 24 192 2X 20 60 1.77
9 P2X 30 30 63.6 300 300 15 --- 5 30 35 24 144 2X 30 30 1.36
P2X 30 40 84.8 300 400 15 --- 5 30 35 24 192 2X 30 40 1.78
P2X 30 50 106.0 300 500 15 --- 5 30 35 24 240 2X 30 50 2.22
P2X 40 40 113.1 400 400 15 --- 5 30 35 24 256 2X 40 40 2.41
P2X 40 60 169.6 400 600 15 --- 5 30 35 24 384 2X 40 60 3.55
P2X 40 100 282.6 400 1000 15 --- 5 30 35 24 656 2X 40 100 5.96
P2X 60 80 339.2 600 800 15 --- 5 30 35 24 768 2X 60 80 7.18
P2X 60 120 508.7 600 1200 15 --- 5 30 35 24 1176 2X 60 120 10.73
P2X 80 100 597.4 800 1000 15 --- 5 30 35 24 1353 2X 80 100 11.93
P2X DO 10 9.0 --- --- 15 100 5 30 35 24 21 2X DO 10 0.14
P2X DO 35 65.4 --- --- 15 350 5 30 35 24 148 2X DO 35 1.49
P2X DO 50 139.6 --- --- 15 500 5 30 35 24 316 2X DO 50 2.48

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.10
SPECIAL PH and P2H SUCTION PLATES FOR OCTOPUS SYSTEMS FOR GRIPPING
EMPTY CANS, TINS, JARS AND VIALS WITHOUT LIDS OR CAPS
The special suction plates illustrated and described on this page can be installed on OCTOPUS
systems to replace the PX and P2X plates.
They are made of anodised aluminium sheets with holes equidistant from each other and
coated with a special sponge rubber, microperforated at the holes in the aluminium sheet, in
3D drawings are available on vuototecnica.net

two different thicknesses: 15 mm for PH suction plates and 30 mm for P2H plates.
The use of calibrated holes makes it possible to calculate the flow rate of the vacuum
generator to be installed on the OCTOPUS SYSTEM, to ensure that, even in the
presence of losses due to transpiration or the absence of some objects to be
picked up, there is always a minimum vacuum value, sufficient to grip even the
few remaining containers.
The use of these suction plates is recommended for gripping and handling empty
cans, tins, vials and jars made of various materials and without lids or caps.
The lifting force of the container will be directly proportional to the degree of vacuum
generated on the surface of the mouth of the can or vial to be picked up.
Note: These plates are not suitable for picking up empty plastic or glass water and wine bottles.
All flexible containers must be previously vacuum tested to avoid the risk of implosion.

Surface (S)

Example of the calculation of the force applied to the container with mouth
diameter 60 mm:
60
SxP 28,26 cm2 x 0,75 Kg/cm2
F= F= = 7,06 Kg
η 3
Where: Where:
F = Lifting force expressed in Kg;
S = Surface area of the container mouth expressed in cm2; S = 28,26 cm2;
P = Force exerted by atmospheric pressure, P = 0,75 Kg/cm2 (value developed from a level
depending on the level of vacuum, expressed in Kg/cm2; of vacuum of -750 mbar);
η = Factor of safety. η = 3.

A B C E F H Holes Only rubber Weight

Item
Ø No. item Kg
PH 15 20 150 200 ~2 5 20 25 48 H 15 20 0.40
PH 20 30 200 300 ~2 5 20 25 96 H 20 30 0.80
PH 20 40 200 400 ~2 5 20 25 128 H 20 40 1.10
PH 20 60 200 600 ~2 5 20 25 192 H 20 60 1.70
PH 30 30 300 300 ~2 5 20 25 144 H 30 30 1.30
PH 30 40 300 400 ~2 5 20 25 192 H 30 40 1.70
PH 30 50 300 500 ~2 5 20 25 240 H 30 50 2.10
PH 40 40 400 400 ~2 5 20 25 256 H 40 40 2.20
PH 40 60 400 600 ~2 5 20 25 384 H 40 60 3.40
PH 40 100 400 1000 ~2 5 20 25 656 H 40 100 5.60
PH 60 80 600 800 ~2 5 20 25 768 H 60 80 6.70
PH 60 120 600 1200 ~2 5 20 25 1176 H 60 120 10.10
PH 80 100 800 1000 ~2 5 20 25 1353 H 80 100 11.30

P2H 15 20 150 200 ~2 5 30 35 48 2H 15 20 0.44

9 P2H 20 30 200 300 ~2 5 30 35 96 2H 20 30 0.89
P2H 20 40 200 400 ~2 5 30 35 128 2H 20 40 1.21
P2H 20 60 200 600 ~2 5 30 35 192 2H 20 60 1.77
P2H 30 30 300 300 ~2 5 30 35 144 2H 30 30 1.36
P2H 30 40 300 400 ~2 5 30 35 192 2H 30 40 1.78
P2H 30 50 300 500 ~2 5 30 35 240 2H 30 50 2.22
P2H 40 40 400 400 ~2 5 30 35 256 2H 40 40 2.41
P2H 40 60 400 600 ~2 5 30 35 384 2H 40 60 3.55
P2H 40 100 400 1000 ~2 5 30 35 656 2H 40 100 5.96
P2H 60 80 600 800 ~2 5 30 35 768 2H 60 80 7.18
P2H 60 120 600 1200 ~2 5 30 35 1176 2H 60 120 10.73
P2H 80 100 800 1000 ~2 5 30 35 1353 2H 80 100 11.93

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.10-110
STANDARD SUCTION PLATES WITH SHUT-OFF VALVES PXE and P2XE
FOR OCTOPUS SYSTEMS
The suction plates described on this page are the same as the previously described
PX and P2X, but with the addition of shut-off valves inserted in each hole. In absence
of an object to grip or in case of a defective grip of the foam rubber, the shut-off
valves automatically close the suction inlet, thus preventing the level of vacuum from

3D drawings are available on vuototecnica.net

decreasing on the other gripping holes.
This feature reduces the vacuum generator flow rate compared to standard OCTOPUS
systems, to the benefit of energy savings. Moreover, the particular shape of our shut-off
valves allows the use of the gripping surfaces in any position.

Force A B C D E F G H Valves Only rubber Weight

Item
Kg Ø Ø No. item Kg
PXE 20 30 42.4 200 300 15 --- 10 15 18 25 96 X 20 30 1.76
PXE 20 40 56.6 200 400 15 --- 10 15 18 25 128 X 20 40 2.38
PXE 20 60 84.8 200 600 15 --- 10 15 18 25 192 X 20 60 3.62
PXE 30 30 63.6 300 300 15 --- 10 15 18 25 144 X 30 30 2.74
PXE 30 40 84.8 300 400 15 --- 10 15 18 25 192 X 30 40 3.62
PXE 30 50 106.0 300 500 15 --- 10 15 18 25 240 X 30 50 4.50
PXE 40 40 113.1 400 400 15 --- 10 15 18 25 256 X 40 40 4.76
PXE 40 60 169.6 400 600 15 --- 10 15 18 25 384 X 40 60 7.24
PXE 40 100 282.6 400 1000 15 --- 10 15 18 25 656 X 40 100 12.16
PXE 60 80 339.2 600 800 15 --- 10 15 18 25 768 X 60 80 14.38
PXE 60 120 508.7 600 1200 15 --- 10 15 18 25 1176 X 60 120 21.86
PXE 80 100 597.4 800 1000 15 --- 10 15 18 25 1353 X 80 100 24.83
PXE DO 35 65.4 --- --- 15 350 10 15 18 25 148 X DO 35 2.78
PXE DO 50 139.6 --- --- 15 500 10 15 18 25 308 X DO 50 5.38

P2XE 20 30 42.4 200 300 15 --- 10 30 18 40 96 2X 20 30 1.85

P2XE 20 40 56.6 200 400 15 --- 10 30 18 40 128 2X 20 40 2.49
P2XE 20 60 84.8 200 600 15 --- 10 30 18 40 192 2X 20 60 3.69
P2XE 30 30 63.6 300 300 15 --- 10 30 18 40 144 2X 30 30 2.80
P2XE 30 40 84.8 300 400 15 --- 10 30 18 40 192 2X 30 40 3.70
P2XE 30 50 106.0 300 500 15 --- 10 30 18 40 240 2X 30 50 4.62
P2XE 40 40 113.1 400 400 15 --- 10 30 18 40 256 2X 40 40 4.97
P2XE 40 60 169.6 400 600 15 --- 10 30 18 40 384 2X 40 60 7.24
P2XE 40 100 282.6 400 1000 15 --- 10 30 18 40 656 2X 40 100 12.52 9
P2XE 60 80 339.2 600 800 15 --- 10 30 18 40 768 2X 60 80 14.86
P2XE 60 120 508.7 600 1200 15 --- 10 30 18 40 1176 2X 60 120 22.49
P2XE 80 100 597.4 800 1000 15 --- 10 30 18 40 1353 2X 80 100 25.46
P2XE DO 35 65.4 --- --- 15 350 10 30 18 40 148 2X DO 35 2.97
P2XE DO 50 139.6 --- --- 15 500 10 30 18 40 308 2X DO 50 5.56

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.11
SPECIAL SUCTION PLATES PY and P2Y FOR OCTOPUS SYSTEMS

Compared to the standard ones, when given the same gripping surface, these suction
plates develop a greater force (item PY) and can grip even very rough and uneven
surfaces (item P2Y).
They are made with anodised aluminium with calibrated holes and coated with special
3D drawings are available on vuototecnica.net

perforated foam rubber, with two different thicknesses upon request.

They are perfectly interchangeable with the standard suction plates.
Their lifting force was calculated considering a level of vacuum of at least -75 Kpa, the
total surface of the holes within the foam rubber and a factor of safety 3.

Force A B C D E F H Holes Only rubber Weight

Item
Kg Ø Ø No. item Kg
PY 15 20 37.7 150 200 40 --- 5 15 20 12 Y 15 20 0.39
PY 20 30 75.4 200 300 40 --- 5 15 20 24 Y 20 30 0.78
PY 20 40 100.5 200 400 40 --- 5 15 20 32 Y 20 40 1.07
PY 20 60 150.8 200 600 40 --- 5 15 20 48 Y 20 60 1.66
PY 30 30 113.0 300 300 40 --- 5 15 20 36 Y 30 30 1.27
PY 30 40 150.8 300 400 40 --- 5 15 20 48 Y 30 40 1.65
PY 30 50 188.4 300 500 40 --- 5 15 20 60 Y 30 50 2.04
PY 40 40 201.0 400 400 40 --- 5 15 20 64 Y 40 40 2.14
PY 40 60 301.5 400 600 40 --- 5 15 20 96 Y 40 60 3.35
PY 40 100 502.4 400 1000 40 --- 5 15 20 164 Y 40 100 5.50
PY 60 80 602.9 600 800 40 --- 5 15 20 192 Y 60 80 6.61
PY 60 120 904.4 600 1200 40 --- 5 15 20 294 Y 60 120 10.01
PY 80 100 1037.3 800 1000 40 --- 5 15 20 315 Y 80 100 11.24
PY DO 35 100.5 --- --- 40 350 5 15 20 37 Y DO 35 1.25
PY DO 50 213.5 --- --- 40 500 5 15 20 79 Y DO 50 2.24

P2Y 15 20 37.7 200 200 40 --- 5 30 35 12 2Y 15 20 0.42

P2Y 20 30 75.4 200 300 40 --- 5 30 35 24 2Y 20 30 0.85
P2Y 20 40 100.5 200 400 40 --- 5 30 35 32 2Y 20 40 1.15
P2Y 20 60 150.8 200 600 40 --- 5 30 35 48 2Y 20 60 1.69
P2Y 30 30 113.0 300 300 40 --- 5 30 35 36 2Y 30 30 1.30
P2Y 30 40 150.8 300 400 40 --- 5 30 35 48 2Y 30 40 1.68
9 P2Y 30 50 188.4 300 500 40 --- 5 30 35 60 2Y 30 50 2.10
P2Y 40 40 201.0 400 400 40 --- 5 30 35 64 2Y 40 40 2.29
P2Y 40 60 301.5 400 600 40 --- 5 30 35 96 2Y 40 60 3.45
P2Y 40 100 502.4 400 1000 40 --- 5 30 35 164 2Y 40 100 5.80
P2Y 60 80 602.9 600 800 40 --- 5 30 35 192 2Y 60 80 7.01
P2Y 60 120 904.4 600 1200 40 --- 5 30 35 294 2Y 60 120 10.60
P2Y 80 100 1037.3 800 1000 40 --- 5 30 35 315 2Y 80 100 11.81
P2Y DO 35 100.5 --- --- 40 350 5 30 35 37 2Y DO 35 1.39
P2Y DO 50 213.5 --- --- 40 500 5 30 35 79 2Y DO 50 2.36

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.12
SPECIAL SUCTION PLATES WITH SHUT-OFF VALVES PY2E and P2Y2E
FOR OCTOPUS SYSTEMS
The suction plates described on this page are the same as the previously described
PY and P2Y, but with the addition of shut-off valves inserted in each hole. In absence
of an object to grip or in case of a defective grip of the foam rubber, the shut-off
valves automatically close the suction inlet, thus preventing the level of vacuum from

3D drawings are available on vuototecnica.net

decreasing on the other gripping holes.
This feature reduces the vacuum generator flow rate compared to OCTOPUS systems
with calibrated holes, to the benefit of energy savings. Also these plates an be used in
any position without altering the operating features.

Force A B C D E F G H Valves Only rubber Weight

Item
Kg Ø Ø No. item Kg
PY2E 20 30 75.4 200 300 40 --- 17 15 18 32 24 Y 20 30 1.26
PY2E 20 40 100.5 200 400 40 --- 17 15 18 32 32 Y 20 40 1.71
PY2E 20 60 150.8 200 600 40 --- 17 15 18 32 48 Y 20 60 2.62
PY2E 30 30 113.0 300 300 40 --- 17 15 18 32 36 Y 30 30 1.99
PY2E 30 40 150.8 300 400 40 --- 17 15 18 32 48 Y 30 40 2.61
PY2E 30 50 188.4 300 500 40 --- 17 15 18 32 60 Y 30 50 3.24
PY2E 40 40 201.0 400 400 40 --- 17 15 18 32 64 Y 40 40 3.42
PY2E 40 60 301.5 400 600 40 --- 17 15 18 32 96 Y 40 60 5.27
PY2E 40 100 502.4 400 1000 40 --- 17 15 18 32 160 Y 40 100 8.70
PY2E 60 80 602.9 600 800 40 --- 17 15 18 32 192 Y 60 80 10.45
PY2E 60 120 904.4 600 1200 40 --- 17 15 18 32 288 Y 60 120 15.77
PY2E 80 100 1037.3 800 1000 40 --- 17 15 18 32 320 Y 80 100 17.64
PY2E DO 35 100.5 --- --- 40 350 17 15 18 32 32 Y DO 35 1.89
PY2E DO 50 213.5 --- --- 40 500 17 15 18 32 76 Y DO 50 3.76

P2Y2E 20 30 75.4 200 300 40 --- 17 30 18 47 24 2Y 20 30 1.33

P2Y2E 20 40 100.5 200 400 40 --- 17 30 18 47 32 2Y 20 40 1.79
P2Y2E 20 60 150.8 200 600 40 --- 17 30 18 47 48 2Y 20 60 2.65
P2Y2E 30 30 113.0 300 300 40 --- 17 30 18 47 36 2Y 30 30 2.02
P2Y2E 30 40 150.8 300 400 40 --- 17 30 18 47 48 2Y 30 40 2.64
P2Y2E 30 50 188.4 300 500 40 --- 17 30 18 47 60 2Y 30 50 3.30
P2Y2E 40 40 201.0 400 400 40 --- 17 30 18 47 64 2Y 40 40 3.57
P2Y2E 40 60 301.5 400 600 40 --- 17 30 18 47 96 2Y 40 60 5.37
P2Y2E 40 100 502.4 400 1000 40 --- 17 30 18 47 160 2Y 40 100 9.00
9
P2Y2E 60 80 602.9 600 800 40 --- 17 30 18 47 192 2Y 60 80 10.85
P2Y2E 60 120 904.4 600 1200 40 --- 17 30 18 47 288 2Y 60 120 16.36
P2Y2E 80 100 1037.3 800 1000 40 --- 17 30 18 47 320 2Y 80 100 18.21
P2Y2E DO 35 100.5 --- --- 40 350 17 30 18 47 32 2Y DO 35 2.03
P2Y2E DO 50 213.5 --- --- 40 500 17 30 18 47 76 2Y DO 50 3.88

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.13
SPECIAL SUCTION PLATES PZ and P2Z FOR OCTOPUS SYSTEMS

Among all the suction plates described up to now, these are the ones which develop the
greatest lifting force given the same gripping surface and level of vacuum. Moreover, the
P2Z version is also able to grip very rough and uneven surfaces.
They are made with light alloys, equipped with calibrated holes and coated with
3D drawings are available on vuototecnica.net

special foam rubber with slot holes, with two different thicknesses. They are perfectly
interchangeable with the standard suction plates.
Their lifting force has been calculated considering a level of vacuum of at least -75 Kpa,
the total surface of the slot holes within the foam rubber and a safety factor 3.

Force A B C D E F G H Holes Only rubber Weight

Item
Kg Ø No. item Kg
PZ 15 20 41.0 150 200 42 --- 5 15 18 20 24 Z 15 20 0.40
PZ 20 30 82.4 200 300 42 --- 5 15 18 20 48 Z 20 30 0.80
PZ 20 40 109.8 200 400 42 --- 5 15 18 20 64 Z 20 40 1.09
PZ 20 60 164.7 200 600 42 --- 5 15 18 20 96 Z 20 60 1.68
PZ 30 30 123.5 300 300 42 --- 5 15 18 20 72 Z 30 30 1.28
PZ 30 40 164.7 300 400 42 --- 5 15 18 20 96 Z 30 40 1.67
PZ 30 50 206.0 300 500 42 --- 5 15 18 20 120 Z 30 50 2.06
PZ 40 40 219.6 400 400 42 --- 5 15 18 20 128 Z 40 40 2.17
PZ 40 60 329.4 400 600 42 --- 5 15 18 20 192 Z 40 60 3.38
PZ 40 100 549.0 400 1000 42 --- 5 15 18 20 328 Z 40 100 5.54
PZ 60 80 658.8 600 800 42 --- 5 15 18 20 384 Z 60 80 6.64
PZ 60 120 988.3 600 1200 42 --- 5 15 18 20 588 Z 60 120 10.05
PZ 80 100 1143.1 800 1000 42 --- 5 15 18 20 660 Z 80 100 11.30
PZ DO 35 126.9 --- --- 42 350 5 15 18 20 74 Z DO 35 1.26
PZ DO 50 271.1 --- --- 42 500 5 15 18 20 158 Z DO 50 2.26

P2Z 15 20 41.0 200 200 42 --- 5 30 18 35 24 2Z 15 20 0.44

P2Z 20 30 82.4 200 300 42 --- 5 30 18 35 48 2Z 20 30 0.88
P2Z 20 40 109.8 200 400 42 --- 5 30 18 35 64 2Z 20 40 1.18
P2Z 20 60 164.7 200 600 42 --- 5 30 18 35 96 2Z 20 60 1.72
P2Z 30 30 123.5 300 300 42 --- 5 30 18 35 72 2Z 30 30 1.33
P2Z 30 40 164.7 300 400 42 --- 5 30 18 35 96 2Z 30 40 1.71
P2Z 30 50 206.0 300 500 42 --- 5 30 18 35 120 2Z 30 50 2.14
9 P2Z 40 40 219.6 400 400 42 --- 5 30 18 35 128 2Z 40 40 2.32
P2Z 40 60 329.4 400 600 42 --- 5 30 18 35 192 2Z 40 60 3.48
P2Z 40 100 549.0 400 1000 42 --- 5 30 18 35 328 2Z 40 100 5.84
P2Z 60 80 658.8 600 800 42 --- 5 30 18 35 384 2Z 60 80 7.05
P2Z 60 120 988.3 600 1200 42 --- 5 30 18 35 588 2Z 60 120 10.64
P2Z 80 100 1143.1 800 1000 42 --- 5 30 18 35 660 2Z 80 100 11.85
P2Z DO 35 126.9 --- --- 42 350 5 30 18 35 74 2Z DO 35 1.42
P2Z DO 50 271.1 --- --- 42 500 5 30 18 35 158 2Z DO 50 2.39

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.14
VACUUM CUP SUCTION PLATES PV and PV2 FOR OCTOPUS SYSTEMS

These suction plates provided with vacuum cups have been designed
to ensure a better grip on uneven and very flexible surfaces (pasta
or candy bags, blister or skin-film packs, thin cardboard boxes, etc.),
which are difficult to grip with suction plates coated with foam rubber.

3D drawings are available on vuototecnica.net

We recommend using bellows cups. Thanks to their great flexibility,
they adapt themselves to any gripping surface, following its profiles and
movements during the lifting phase, guaranteeing a firm and safe grip.
They are made with anodised aluminium, as are the vacuum cup
supports screwed onto them, which are 1/8” gas supports for
the PV version and 1/4”gas for the P2V version. They are each
equipped with a calibrated hole.
The cups are cold assembled onto the supports with no adhesives
and can be provided in other compounds. Also these suction plates
are perfectly interchangeable with the standard ones.
Their lifting force has been calculated considering a level of vacuum of
at least -75 Kpa, the total vacuum cup surface and a safety factor 3.
Upon request, they can be provided with different cups, as long as the
diameter does not exceed 22 mm for the PV suction plates and 45
mm for the P2V ones.

Force A B C D E F H Vacuum cup example Vacuum cups Weight

Item
Kg Ø Ø item No. Kg
PV 15 20 30.2 150 200 18 --- 5 36 41 01 18 29 48 0.54
PV 20 30 60.5 200 300 18 --- 5 36 41 01 18 29 96 1.13
PV 20 40 80.6 200 400 18 --- 5 36 41 01 18 29 128 1.54
PV 20 60 121.0 200 600 18 --- 5 36 41 01 18 29 192 2.37
PV 30 30 90.7 300 300 18 --- 5 36 41 01 18 29 144 1.80
PV 30 40 121.0 300 400 18 --- 5 36 41 01 18 29 192 2.37
PV 30 50 151.2 300 500 18 --- 5 36 41 01 18 29 240 2.94 9
PV 40 40 167.0 400 400 18 --- 5 36 41 01 18 29 256 3.09
PV 40 60 242.0 400 600 18 --- 5 36 41 01 18 29 384 4.74
PV 40 100 413.3 400 1000 18 --- 5 36 41 01 18 29 656 7.89
PV 60 80 483.9 600 800 18 --- 5 36 41 01 18 29 768 9.38
PV 60 120 740.8 600 1200 18 --- 5 36 41 01 18 29 1176 14.21
PV 80 100 852.4 800 1000 18 --- 5 36 41 01 18 29 1353 16.03
PV DO 35 93.2 --- --- 18 350 5 36 41 01 18 29 148 1.81
PV DO 50 194.0 --- --- 18 500 5 36 41 01 18 29 300 3.37
NOTE: The code PV .. .. only identifies the suction plate with the relative supports for the vacuum cups screwed onto it.
The vacuum cups indicated in the table or those chosen freely are not included with the suction plate and therefore must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.15
VACUUM CUP SUCTION PLATES PV2 FOR OCTOPUS SYSTEMS
3D drawings are available on vuototecnica.net

Force A B C D E F H Vacuum cup example Vacuum cups Weight

Item
Kg Ø Ø item No. Kg
P2V 15 20 37.7 150 200 40 --- 5 51.5 56.5 01 40 42 12 0.56
P2V 20 30 75.4 200 300 40 --- 5 51.5 56.5 01 40 42 24 1.12
P2V 20 40 100.5 200 400 40 --- 5 51.5 56.5 01 40 42 32 1.67
P2V 20 60 150.8 200 600 40 --- 5 51.5 56.5 01 40 42 48 2.24
P2V 30 30 113.0 300 300 40 --- 5 51.5 56.5 01 40 42 36 1.68
P2V 30 40 150.8 300 400 40 --- 5 51.5 56.5 01 40 42 48 2.24
P2V 30 50 188.4 300 500 40 --- 5 51.5 56.5 01 40 42 60 2.80
9 P2V 40 40 201.0 400 400 40 --- 5 51.5 56.5 01 40 42 64 3.34
P2V 40 60 301.5 400 600 40 --- 5 51.5 56.5 01 40 42 96 4.48
P2V 40 100 502.4 400 1000 40 --- 5 51.5 56.5 01 40 42 160 8.35
P2V 60 80 602.9 600 800 40 --- 5 51.5 56.5 01 40 42 192 8.96
P2V 60 120 904.3 600 1200 40 --- 5 51.5 56.5 01 40 42 288 13.44
P2V 80 100 1004.8 800 1000 40 --- 5 51.5 56.5 01 40 42 320 16.70
P2V DO 35 100.5 --- --- 40 350 5 51.5 56.5 01 40 42 32 1.67
P2V DO 50 213.5 --- --- 40 500 5 51.5 56.5 01 40 42 76 3.17
NOTE: The code P2V .. .. only identifies the suction plate with the relative supports for the vacuum cups screwed onto it.
The vacuum cups indicated in the table or those chosen freely are not included with the suction plate and therefore must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.16
VACUUM CUP SUCTION PLATES WITH SHUT-OFF VALVES PVE and P2V2E
FOR OCTOPUS SYSTEMS
The suction plates described on this page are the same as the
previously described PY and P2V, but with the addition of shut-off
valves inserted in each vacuum cup support connection. In absence
of an object to grip or in case of a defective grip of the cup, the

3D drawings are available on vuototecnica.net

shut-off valves automatically close the suction inlet, thus preventing
the level of vacuum from decreasing on the other gripping vacuum
cups. This feature reduces the vacuum generator flow rate compared
to OCTOPUS systems with calibrated holes, to the benefit of energy
savings. Also these plates an be used in any position without
compromising correct operation.

Force A B C D E F G H Vacuum cup Valves and vacuum Weight

Item
Kg Ø Ø example item cups No. Kg
PVE 20 30 60.5 200 300 18 --- 10 36 18 46 01 18 29 96 2.09
PVE 20 40 80.6 200 400 18 --- 10 36 18 46 01 18 29 128 2.82
PVE 20 60 121.0 200 600 18 --- 10 36 18 46 01 18 29 192 4.18
PVE 30 30 90.7 300 300 18 --- 10 36 18 46 01 18 29 144 3.24
PVE 30 40 121.0 300 400 18 --- 10 36 18 46 01 18 29 192 4.18
PVE 30 50 151.2 300 500 18 --- 10 36 18 46 01 18 29 240 6.27
PVE 40 40 167.0 400 400 18 --- 10 36 18 46 01 18 29 256 5.64
9
PVE 40 60 242.0 400 600 18 --- 10 36 18 46 01 18 29 384 8.36
PVE 40 100 413.3 400 1000 18 --- 10 36 18 46 01 18 29 656 14.45
PVE 60 80 483.9 600 800 18 --- 10 36 18 46 01 18 29 768 17.06
PVE 60 120 740.8 600 1200 18 --- 10 36 18 46 01 18 29 1176 25.97
PVE 80 100 852.4 800 1000 18 --- 10 36 18 46 01 18 29 1353 29.56
PVE DO 35 93.2 --- --- 18 350 10 36 18 46 01 18 29 148 3.29
PVE DO 50 194.0 --- --- 18 500 10 36 18 46 01 18 29 308 6.45
NOTE: The code PVE .. .. only identifies the suction plate with the relative supports for the vacuum cups screwed onto it and the built-in shut-off valves.
The vacuum cups indicated in the table or those chosen freely are not included with the suction plate and therefore must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.17
VACUUM CUP SUCTION PLATES WITH SHUT-OFF VALVES P2V2E
FOR OCTOPUS SYSTEMS
3D drawings are available on vuototecnica.net

Force A B C D E F G H Vacuum cup Valves and vacuum Weight

Item
Kg Ø Ø example item cups No. Kg
P2V2E 20 30 75.4 200 300 40 --- 17 51.5 18 68.5 01 40 42 24 1.60
P2V2E 20 40 100.5 200 400 40 --- 17 51.5 18 68.5 01 40 42 32 2.31
P2V2E 20 60 150.8 200 600 40 --- 17 51.5 18 68.5 01 40 42 48 3.20
P2V2E 30 30 113.0 300 300 40 --- 17 51.5 18 68.5 01 40 42 36 2.40
P2V2E 30 40 150.8 300 400 40 --- 17 51.5 18 68.5 01 40 42 48 3.20
P2V2E 30 50 188.4 300 500 40 --- 17 51.5 18 68.5 01 40 42 60 4.00
9 P2V2E 40 40 201.0 400 400 40 --- 17 51.5 18 68.5 01 40 42 64 4.62
P2V2E 40 60 301.5 400 600 40 --- 17 51.5 18 68.5 01 40 42 96 6.40
P2V2E 40 100 502.4 400 1000 40 --- 17 51.5 18 68.5 01 40 42 160 11.55
P2V2E 60 80 602.9 600 800 40 --- 17 51.5 18 68.5 01 40 42 192 12.80
P2V2E 60 120 904.3 600 1200 40 --- 17 51.5 18 68.5 01 40 42 288 19.20
P2V2E 80 100 1004.8 800 1000 40 --- 17 51.5 18 68.5 01 40 42 320 23.10
P2V2E DO 35 100.5 --- --- 40 350 17 51.5 18 68.5 01 40 42 32 2.31
P2V2E DO 50 213.5 --- --- 40 500 17 51.5 18 68.5 01 40 42 76 4.53
NOTE: The code P2V2E .. .. only identifies the suction plate with the relative supports for the vacuum cups screwed onto it and the built-in shut-off valves.
The vacuum cups indicated in the table or those chosen freely are not included with the suction plate and therefore must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.18
BAG GRIPPING SUCTION PLATES PJ
FOR OCTOPUS SYSTEMS
These suction plates have been designed to allow gripping paper or plastic bags
containing powders, granulated products, bulk products or liquids. These suction plates
are associated with OCTOPUS systems that fully exploit their performance. They are made
with anodised aluminium and are provided with a special foam rubber seal. They are

3D drawings are available on vuototecnica.net

perfectly interchangeable with the OCTOPUS system standard suction plates. The special
shapes of the seal and the face allow reducing bag deformation during gripping, reducing
vacuum loss to a minimum and guaranteeing the largest gripping surface possible.
Their lifting force has been calculated considering a level of vacuum of at least -75 Kpa,
the total gripping surface enclosed in the seal and a safety factor 3.

Force A B C E F G H Only rubber Weight

Item
Kg item Kg
PJ 07 12 4.0 70 120 100 5.0 15 50 15.0 J 07 12 0.09
PJ 08 08 3.0 80 80 60 5.0 15 60 15.0 J 08 08 0.08
9
PJ 15 20 24.6 150 200 170 7.5 15 120 22.5 J 15 20 0.46
PJ 20 30 73.4 200 300 230 10.0 30 130 40.0 J 20 30 0.92
PJ 20 40 106.0 200 400 330 10.0 30 130 40.0 J 20 40 1.25
PJ 20 60 171.0 200 600 530 10.0 30 130 40.0 J 20 60 1.84
PJ 30 40 188.4 300 400 330 10.0 30 230 40.0 J 30 40 1.84
PJ 30 50 246.0 300 500 430 10.0 30 230 40.0 J 30 50 2.30
PJ 40 60 436.0 400 600 530 10.0 30 330 40.0 J 40 60 3.68

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.19
OCTOPUS VACUUM GRIPPING BARS - GENERAL DESCRIPTION

These bars have been created to further facilitate the installation of OCTOPUS vacuum gripping systems on palletising robots. They
are based on the same operating principle and, in addition to the advantages and technical features of the standard OCTOPUS, are
equipped with a grooved support plate to allow quick installation on the machine and easy positioning with respect to the load to be
gripped.
3D drawings are available on vuototecnica.net

They are in fact composed of:

- A slotted anodised aluminium fixing plate for quick installation onto the machine
- One or more compressed air-fed vacuum generators, depending on their size
- A connection equipped with quick coupling for feeding compressed air to the generators
- An anodised aluminium box, open on one side, with two air inlet connections inside at the end of the cycle, for quick restoration of the
atmospheric pressure and one for possible installation of a vacuum switch.
- A suction plate sealing the box, also made with anodised aluminium, with calibrated holes equidistant from each other and coated
with a special perforated foam rubber. This suction plate can thus perfectly adapt to any gripping surface, whether it be smooth,
rough or irregular. With the same bar, for example, it is possible to grip and move wooden joists or metal profiles and the pallet that
supports them.
The OCTOPUS gripping bars described so far are the standard bars: they can be supplied upon request with suction plates and with
shut-off valves and, to make them even lighter, the aluminium parts can be made of Polizene, a thermoplastic material that decreases
the weight by about 40%.

2
3

9
9

9.20
3D drawings are available on vuototecnica.net
COMPOSITION OF THE OCTOPUS GRIPPING BARS

The OCTOPUS gripping bars are composed of:

1 A grooved support plate made of anodised aluminium for
rapid installation on the machine and easy positioning with
respect to the load to be picked up.

2 One or more compressed air-fed vacuum generators,

depending on the size of the bars.

3 An anodised aluminium box, open on one side, with two air

inlet connections inside at the end of the cycle, for quick
restoration of the atmospheric pressure and one for possible
installation of a vacuum switch.

4 A micro-perforated anodised aluminium suction plate to close the

bar body, coated with special perforated foam rubber 5 , with
15 mm diameter holes, axial to the calibrated holes of the plate,
with thickness 20 mm (PX) or 30 mm (P2X) or with bellows 6
vacuum cups 18 mm (PV).

Or:

7 A suction plate with shut-off valves coated with foam rubber

8 , with 15 mm diameter holes, thickness 20 mm (PXE) or
30 mm (P2XE) or with vacuum cups 9 diameter 18 mm
(PVE).

4
9

9.21
OCTOPUS VACUUM GRIPPING BARS
3D drawings are available on vuototecnica.net

Vacuum Vacuum generator 4 silencers SSX 1/4”

generator PVP 25 MX PBO
for plate with calibrated holes

connection G1/4”
Compressed air connection P

Compressed air connection P

Connection for Vacuum generator

for plate with shut-off valves

vacuum switch G 1/8” PVP 25 MX PBO

Air blow off

Item BO O8 60 X BO O8 80 X BO O8 100 X
Suction plate item PX 08 60 PX O8 80 PX O8 100
Gripping force Kg 31.7 42.2 54.1
Fitted for vacuum generators item N°2 PVP 25 MX PBO N°2 PVP 25 MX PBO N°2 PVP 25 MX PBO
Maximum supply pressure bar 6 6 6
Maximum level of vacuum -KPa 90 90 90
Air consumption at 6 bar Nl/s 6.4 6.4 6.4
Intake air flow rate m3/h 62 62 62
Temperature of use °C -20 / +80 -20 / +80 -20 / +80
Weight Kg 6 8 10
A 600 800 1000
B 80 80 80
9 C 21 21 21
D 50 50 50
E 5.2 5.2 5.2
F 4.8 4.8 4.8
G 10 10 10
H 112 112 112
P Connection for compressed air tube Ø ext. 8 8 8
NOTE: The code BO 08 .. X identifies the body of the OCTOPUS bar with relative suction plate PX, the grooved support plate and the vacuum generators indicated in the table.
Add the letters CD to the item for an Octopus bar supplied without vacuum generators and with closing plates with distributor item 00 BO 07 assembled (Example: BO 08 80 X CD).
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.22
OCTOPUS VACUUM GRIPPING BARS

3D drawings are available on vuototecnica.net

Vacuum Vacuum generator 4 silencers SSX 1/4”
generator PVP 25 MX PBO

Connection for Vacuum generator

connection G1/4”
for plate with calibrated holes
Compressed air connection P

Compressed air connection P

for plate with shut-off valves

vacuum switch G 1/8” PVP 25 MX PBO

Air blow off

Item BO 12 40 X BO 12 60 X BO 12 80 X
Suction plate item PX 12 40 PX 12 60 PX 12 80
Gripping force Kg 25.7 42.2 56.3
Fitted for vacuum generators item N°1 PVP 25 MX PBO N°2 PVP 25 MX PBO N°2 PVP 25 MX PBO
Maximum supply pressure bar 6 6 6
Maximum level of vacuum -KPa 90 90 90
Air consumption at 6 bar Nl/s 3.2 6.4 6.4
Intake air flow rate m3/h 31 62 62
Temperature of use °C -20 / +80 -20 / +80 -20 / +80
Weight Kg 4.5 8.1 10.8
A 400 600 800
B 120 120 120
C 21 21 21 9
D 90 90 90
E 5.2 5.2 5.2
F 4.8 4.8 4.8
G 10 10 10
H 112 112 112
P Connection for compressed air tube Ø ext. 8 8 8
NOTE: The code BO 12 .. X identifies the body of the OCTOPUS bar with relative suction plate PX, the grooved support plate and the vacuum generators indicated in the table.
Add the letters CD to the item for an Octopus bar supplied without vacuum generators and with closing plates with distributor item 00 BO 07 assembled (Example: BO 12 60 X CD).
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.23
OCTOPUS VACUUM GRIPPING BARS
3D drawings are available on vuototecnica.net

Vacuum Vacuum generator Vacuum generator 4 silencers SSX 1/4”

generator PVP 25 MX PBO PVP 25 MX PBO

Connection for Connection for Vacuum generator

vacuum switch G 1/8” vacuum switch G 1/8” PVP 25 MX PBO
connection G1/4”
for plate with calibrated holes
Compressed air connection P

Compressed air connection P

for plate with shut-off valves
Air blow off

Item BO 12 100 X BO 08 120 X BO 12 120 X BO 12 140 X

Suction plate item PX 12 100 PX 08 120 PX 12 120 PX 12 140
Gripping force Kg 72.2 64.7 86.2 100.3
Fitted for vacuum generators item N°3 PVP 25 MX PBO N°3 PVP 25 MX PBO N°3 PVP 25 MX PBO N°4 PVP 25 MX PBO
Maximum supply pressure bar 6 6 6 6
Maximum level of vacuum -KPa 90 90 90 90
Air consumption at 6 bar Nl/s 9.6 9.6 9.6 12.8
Intake air flow rate m3/h 93 93 93 124
Temperature of use °C -20 / +80 -20 / +80 -20 / +80 -20 / +80
Weight Kg 14.5 13 17.4 20.8
A 1000 1200 1200 1400
B 120 80 120 120
9 C 21 21 21 21
D 90 50 90 90
E 5.2 5.2 5.2 5.2
F 4.8 4.8 4.8 4.8
G 10 10 10 10
H 112 112 112 112
P Connection for compressed air tube Ø ext. 8 8 8 8
NOTE: The code BO .. .. X identifies the body of the OCTOPUS bar with relative suction plate PX, the grooved support plate and the vacuum generators indicated in the table.
Add the letters CD to the item for an Octopus bar supplied without vacuum generators and with closing plates with distributor item 00 BO 07 assembled (Example: BO 12 100 X CD).
NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.24
STANDARD SUCTION PLATES PX and P2X FOR OCTOPUS GRIPPING BARS

The suction plates PX described on this page are installed as standard

on all OCTOPUS gripping bars and, therefore, can be supplied as a
spare or replacement part.
They are made with anodised aluminium sheets with calibrated holes

3D drawings are available on vuototecnica.net

equidistant from each other and coated with a special perforated foam
rubber with two different thicknesses: 20 mm for suction plates of the
PX range and 30 mm for special plates P2X. Their lifting force was
calculated considering a level of vacuum of at least -75 Kpa, the total
surface of the holes within the foam rubber and a factor of safety 3.

Force A B C E F H Holes I L Only rubber Weight

Item
Kg Ø No. item Kg
PX 08 60 31.7 80 600 15 5 20 25 72 24 24 00 BO 12 0.70
PX 08 80 42.2 80 800 15 5 20 25 96 24 24 00 BO 18 0.94
PX 08 100 54.1 80 1000 15 5 20 25 123 24 24 00 BO 97 1.06
PX 08 120 64.7 80 1200 15 5 20 25 147 24 24 00 BO 101 1.12
PX 12 40 25.7 120 400 20 5 20 25 33 34 35 00 BO 68 0.70
PX 12 60 42.2 120 600 15 5 20 25 96 24 24 00 BO 27 1.06
PX 12 80 56.3 120 800 15 5 20 25 128 24 24 00 BO 05 1.41
PX 12 100 72.2 120 1000 15 5 20 25 164 24 24 00 BO 36 1.75
PX 12 120 86.2 120 1200 15 5 20 25 196 24 24 00 BO 40 2.11
PX 12 140 100.3 120 1400 15 5 20 25 228 24 24 00 BO 63 2.47

P2X 08 60 31.7 80 600 15 5 30 35 72 24 24 00 BO 79 0.72

P2X 08 80 42.2 80 800 15 5 30 35 96 24 24 00 BO 80 0.96
9
P2X 08 100 54.1 80 1000 15 5 30 35 123 24 24 00 BO 106 1.10
P2X 08 120 64.7 80 1200 15 5 30 35 147 24 24 00 BO 107 1.18
P2X 12 40 25.7 120 400 20 5 30 35 33 34 35 00 BO 81 0.78
P2X 12 60 42.2 120 600 15 5 30 35 96 24 24 00 BO 82 1.10
P2X 12 80 56.3 120 800 15 5 30 35 128 24 24 00 BO 83 1.45
P2X 12 100 72.2 120 1000 15 5 30 35 164 24 24 00 BO 84 1.80
P2X 12 120 86.2 120 1200 15 5 30 35 196 24 24 00 BO 85 2.17
P2X 12 140 100.3 120 1400 15 5 30 35 228 24 24 00 BO 86 2.54

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.25
VACUUM CUP SUCTION PLATES PV FOR OCTOPUS GRIPPING BARS

We recommend using bellows cups. Thanks to their great flexibility,

they adapt themselves to any gripping surface, following its profiles and
movements during the lifting phase, guaranteeing a firm and safe grip.
They are made with anodised aluminium, as are the vacuum cup
supports screwed onto them, which are 1/8” gas supports and are
each equipped with a calibrated hole.
The cups are cold assembled onto the supports with no adhesives
and can be provided in other compounds. Also these suction plates
are perfectly interchangeable with the standard ones.
Their lifting force has been calculated considering a level of vacuum
of at least -75 Kpa, the total vacuum cup gripping surface and a safety
factor 3.
They can be supplied upon request with different vacuum cups,
provided that their diameter is no larger than 22 mm.

Force A B C E F H Vacuum cup example I L Vacuum cups Weight

Item
Kg Ø item No. Kg
PV 08 60 45.4 80 600 18 5 36 41 01 18 29 24 24 72 0.83
PV 08 80 60.5 80 800 18 5 36 41 01 18 29 24 24 96 1.26
PV 08 100 75.6 80 1000 18 5 36 41 01 18 29 24 24 120 1.52
9 PV 08 120 92.6 80 1200 18 5 36 41 01 18 29 24 24 147 1.82

PV 12 40 20.8 120 400 18 5 36 41 01 18 29 34 35 33 1.14

PV 12 60 60.5 120 600 18 5 36 41 01 18 29 24 24 96 1.42
PV 12 80 80.6 120 800 18 5 36 41 01 18 29 24 24 128 1.90
PV 12 100 100.8 120 1000 18 5 36 41 01 18 29 24 24 160 2.37
PV 12 120 121.0 120 1200 18 5 36 41 01 18 29 24 24 192 2.84
PV 12 140 143.7 120 1400 18 5 36 41 01 18 29 24 24 228 3.40
NOTE: The code PV .. .. only identifies the suction plate with the relative supports for the vacuum cups screwed onto it.
The vacuum cups indicated in the table or those chosen freely are not included with the suction plate and therefore must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.26
SUCTION PLATES WITH SHUT-OFF VALVES PXE and P2XE
FOR OCTOPUS GRIPPING BARS
The suction plates described on this page are the same as the
previously described PX and P2X, but with the addition of shut-
off valves inserted in each hole. In absence of an object to grip or
in case of a defective grip of the foam rubber, the shut-off valves

3D drawings are available on vuototecnica.net

automatically close the suction inlet, thus preventing the level of
vacuum from decreasing on the other gripping holes.
This feature reduces the vacuum generator flow rate compared to
standard OCTOPUS gripping bars, to the benefit of energy savings.
Moreover, the particular shape of our shut-off valves allows the use of
the gripping surfaces in any position.

Force A B C E F G H I L M Valves Only rubber Weight

Item
Kg Ø No. item Kg
PXE 08 60 43.7 80 600 20 10 20 18 30 30 20 15 56 00 BO 21 1.69
PXE 08 80 60.0 80 800 20 10 20 18 30 30 20 15 77 00 BO 25 2.25
PXE 08 100 74.1 80 1000 20 10 20 18 30 30 20 15 95 00 BO 111 2.27
PXE 08 120 90.5 80 1200 20 10 20 18 30 30 20 15 116 00 BO 113 2.54
PXE 12 40 25.7 120 400 20 10 20 18 30 34 35 15 33 00 BO 68 2.03
PXE 12 60 42.1 120 600 20 10 20 18 30 40 25 20 54 00 BO 32 2.53
PXE 12 80 57.7 120 800 20 10 20 18 30 40 25 20 74 00 BO 23 3.38
PXE 12 100 73.3 120 1000 20 10 20 18 30 40 25 20 94 00 BO 43 4.22
PXE 12 120 88.9 120 1200 20 10 20 18 30 40 25 20 114 00 BO 45 5.07
PXE 12 140 104.5 120 1400 20 10 20 18 30 40 25 20 134 00 BO 76 6.08

P2XE 08 60 43.7 80 600 20 10 30 18 40 30 20 15 56 00 BO 87 1.72

P2XE 08 80 60.0 80 800 20 10 30 18 40 30 20 15 77 00 BO 88 2.28
P2XE 08 100 74.1 80 1000 20 10 30 18 40 30 20 15 95 00 BO 114 2.30
9
P2XE 08 120 90.5 80 1200 20 10 30 18 40 30 20 15 116 00 BO 115 2.58
P2XE 12 40 25.7 120 400 20 10 30 18 40 34 35 15 33 00 BO 81 2.06
P2XE 12 60 42.1 120 600 20 10 30 18 40 40 25 20 54 00 BO 89 2.58
P2XE 12 80 57.7 120 800 20 10 30 18 40 40 25 20 74 00 BO 90 3.44
P2XE 12 100 73.3 120 1000 20 10 30 18 40 40 25 20 94 00 BO 91 4.30
P2XE 12 120 88.9 120 1200 20 10 30 18 40 40 25 20 114 00 BO 92 5.16
P2XE 12 140 104.5 120 1400 20 10 30 18 40 40 25 20 134 00 BO 93 6.16

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.27
VACUUM CUP SUCTION PLATES WITH SHUT-OFF VALVES PVE
FOR OCTOPUS GRIPPING BARS
The suction plates described on this page are the same as the
previously described PY and P2V, but with the addition of shut-off
valves inserted in each vacuum cup support connection. In absence
of an object to grip or in case of a defective grip of the cup, the shut-
3D drawings are available on vuototecnica.net

off valves automatically close the suction inlet, thus preventing the
level of vacuum from decreasing on the other gripping vacuum cups.
This feature reduces the vacuum generator flow rate compared to
standard OCTOPUS gripping bars with calibrated holes, to the benefit
of energy savings. Their particular shape of our shut-off valves allows
the use of the gripping surfaces in any position.

Force A B C E F G H I L M Vacuum cup example Valves and vacuum cups Weight

Item
Kg Ø item No. Kg
PVE 08 60 35.3 80 600 18 10 36 18 46 30 20 15 01 18 29 56 1.96
PVE 08 80 48.5 80 800 18 10 36 18 46 30 20 15 01 18 29 77 2.61
PVE 08 100 59.9 80 1000 18 10 36 18 46 30 20 15 01 18 29 95 2.91
9
PVE 08 120 73.0 80 1200 18 10 36 18 46 30 20 15 01 18 29 116 3.28

PVE 12 40 20.8 120 400 18 10 36 18 46 34 35 -- 01 18 29 33 2.35

PVE 12 60 34.0 120 600 18 10 36 18 46 40 25 20 01 18 29 54 2.93
PVE 12 80 46.6 120 800 18 10 36 18 46 40 25 20 01 18 29 74 3.92
PVE 12 100 59.2 120 1000 18 10 36 18 46 40 25 20 01 18 29 94 4.89
PVE 12 120 71.8 120 1200 18 10 36 18 46 40 25 20 01 18 29 114 5.88
PVE 12 140 84.4 120 1400 18 10 36 18 46 40 25 20 01 18 29 134 7.05
NOTE: The code PVE .. .. only identifies the suction plate with the relative supports for the vacuum cups screwed onto it and the built-in shut-off valves.
The vacuum cups indicated in the table or those chosen freely are not included with the suction plate and therefore must be ordered separately.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.28
LOCKING PLATE WITH DISTRIBUTOR FOR
OCTOPUS GRIPPING BARS WITHOUT VACUUM GENERATOR
The locking plates with distributor described on this page have
been designed to connect an OCTOPUS gripping bar to a remotely
installed vacuum generator or to an alternative vacuum source.
The plate, made of anodised aluminium, is fastened with screws

3D drawings are available on vuototecnica.net

to the body of the OCTOPUS bar in place of the generator. The
distributor is equipped with connections for direct connection to
the OCTOPUS bar, to the generator or to the alternative vacuum
source and to the instruments for reading and control of the level of
vacuum. The unused connections can be closed with the metal caps
provided.
The locking plate with distributor is suitable for all OCTOPUS gripping
bars that use vacuum generators PVP 12 MX and PVP 25 MX.

Locking plate

Vacuum generator

9.29
LOCKING PLATE WITH DISTRIBUTOR FOR
OCTOPUS GRIPPING BARS WITHOUT VACUUM GENERATOR
3D drawings are available on vuototecnica.net

Item For OCTOPUS gripping bars

00 BO 07 BO 08 60 X - BO 08 80 X
BO 08 100 X - BO 08 120 X
BO 12 40 X - BO 12 60 X
BO 12 80 X - BO 12 100 X
BO 12 120 X - BO 12 140 X

Vacuum
connection
Vacuum
connection

Vacuum 10 M5 holes for fixing to

connection OCTOPUS bar

LOCKING PLATE FOR

OCTOPUS GRIPPING BARS WITHOUT VACUUM GENERATOR
Use the locking plate illustrated and described on this page to close the suction holes on
the body of the OCTOPUS bar, left free by the removal of the vacuum generator.
The plate, made of anodised aluminium, is fastened with screws to the body of the
OCTOPUS bar in place of the generator. The seal with which it is provided ensures a
perfect vacuum seal.
The locking plate is suitable for all OCTOPUS gripping bars that use vacuum generators
PVP 12 MX and PVP 25 MX.

Item For OCTOPUS gripping bars

00 BO 06 BO 08 60 X - BO 08 80 X
BO 08 100 X - BO 08 120 X
BO 12 40 X - BO 12 60 X
BO 12 80 X - BO 12 100 X
BO 12 120 X - BO 12 140 X

10 M5 holes for fixing to

OCTOPUS bar

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.30
FLANGE FIXING SUPPORT FOR OCTOPUS SYSTEMS
WITHOUT VACUUM GENERATOR
The fixing supports described on this page have been designed
to connect an OCTOPUS system to a remotely installed vacuum
generator or to an alternative vacuum source.
The supports, made with anodised aluminium, have two flanges: one

3D drawings are available on vuototecnica.net

to be fixed on the OCTOPUS system in the place of the generator and
the other on the machine.
They are also equipped with connections for direct connection to
the OCTOPUS system, to the generator or to the alternative vacuum
source and to the instruments for reading and control of the level of
vacuum. The unused connections can be closed with the metal caps
provided.
The flange supports are currently available in the versions shown on
this page and are suitable for OCTOPUS systems that use the vacuum
generators indicated to beside the item:
- Item SO 00 02 PVP 100 ÷ 200M
- Item SO 00 05 PVP 150 ÷ 300MD
- Item SO 00 06 PVP 450 MD
NOTE: The vacuum gauges and vacuum switches shown in the photo
are not included with the supports.

Item S0 00 02

8 M5 holes for fixing to

OCTOPUS bar
Connections for vacuum gauge
and vacuum switch

Item S0 00 05
Item S0 00 06

8 M5 holes for fixing to

OCTOPUS bar
Connections for vacuum gauge
and vacuum switch
9

A B C D E F G H I L M N Weight
Item
Ø Ø Kg
SO 00 02 100 100 210 80 10 194 8 76 12 50 G1” 1/2 8.5 2.8
SO 00 05 150 120 150 130 10 134 8 96 12 75 G2” 8.5 4.2
SO 00 06 150 145 150 130 10 134 8 121 12 75 G2” 1/2 8.5 4.3

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.31
ACCESSORIES AND SPARE PARTS FOR OCTOPUS GRIPPING SYSTEMS AND BARS

Digital vacuum switch with 1/8” gas axial connection

3D drawings are available on vuototecnica.net

Item Description
12 10 10 Digital vacuum switch

Electrical cable with axial connector

Item Description
Electrical connection cable with M8 - 4 pin axial connector
00 12 20
for digital vacuum switch length 5 m

Electrical cable with radial connector

Item Description
Electrical connection cable with M8 - 4 pin radial connector
00 12 21
for digital vacuum switch length 5 m

Vacuum gauge Ø 40 mm with 1/8” coaxial gas coupler

Item Description
09 03 15 Vacuum gauge

Pressure gauge Ø 40 mm with 1/8” coaxial gas coupler

Item Description
09 03 25 Pressure gauge

9.32
ACCESSORIES AND SPARE PARTS FOR OCTOPUS GRIPPING SYSTEMS AND BARS

Silencer

3D drawings are available on vuototecnica.net

Item For generator item
SSX 1/4” PVP 25 MX PO - PVP 25 MX PBO

Sealing kit and reed valves

Item For generator item

00 KIT PVP 25 MX PVP 25 MX PO - PVP 25 MX PBO

Item For generator item

00 KIT PVP 100 M PVP 100 M PO
00 KIT PVP 140 M PVP 140 M PO
00 KIT PVP 170 M PVP 170 M PO
00 KIT PVP 200 M PVP 200 M PO

Item For generator item

00 KIT PVP 150 MD PVP 150 MD PO
00 KIT PVP 300 MD PVP 300 MD PO
00 KIT PVP 450 MD PVP 450 MD PO

9.33
ACCESSORIES AND SPARE PARTS FOR OCTOPUS GRIPPING SYSTEMS AND BARS

Stainless steel disc filters

3D drawings are available on vuototecnica.net

D For OCTOPUS systems

Item

00 SO 05 25 SO 15 20 - BO 08 60 - BO 08 80 - BO 08 100 - BO 08 120
BO 12 40 - BO 12 60 - BO 12 80 - BO 12 100 - BO 12 120 - BO 12 140

00 SO 10 50 SO 20 30 - SO 20 40 - SO 20 60 - SO DO 35

00 SO 14 80 SO 30 30 - SO 30 40 - SO 30 50 - SO 40 40
SO 40 60 - SO DO 50 - SO 40 100 - SO 60 80
SO 60 120 - SO 80 100

Supports for vacuum cups with calibrated hole

Hex. 12

D Weight Support For vacuum cup

Item
Ø g material item
00 08 157 1.5 4 aluminium 01 18 29
00 08 178 2.5 4 aluminium 01 18 29

Sp17

D Weight Support For vacuum cup

Item
Ø g material item
00 08 158 1,5 8 aluminium 01 40 42
00 08 425 5 8 aluminium 01 40 42

Sp13

Weight Support For vacuum cup

Item
g material item
00 08 170 4 aluminium 01 20 23

Shut-off valves

A B d D E H Ch Weight Support
9 Item
Ø Ø Ø Ø g material
14 01 06 G1/4” G1/8” 3.25 15 18 28 12 10 aluminium
Minimum trigger flow = 1.5 m /h
3
Minimum level of vacuum = -250 mbar

A B d D E H Ch Weight Support
Item
Ø Ø Ø Ø g material
Sp
14 01 07 G3/8” G1/4” 4.50 20 25 35 17 24 aluminium
Minimum trigger flow = 4 m3/h Minimum level of vacuum = -250 mbar

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
9.34
SPECIAL OCTOPUS GRIPPING SYSTEM PRODUCTS

3D drawings are available on vuototecnica.net

mm 270x420 - SO 27 42 2V mm 330x550 - SO 33 55 2V

mm 180x210 - SO 18 21 2C X mm 70x200 - SO 07 20 X

mm 200x1000 - SO 20 100 X

9.35
SPECIAL OCTOPUS GRIPPING SYSTEM PRODUCTS
3D drawings are available on vuototecnica.net

mm 300x360 with fixing support - SO 30 36 X mm 70x140 with digital vacuum switch - SO 07 14 V

mm 210x360 with 3 independent mm Ø400 with fixing support and vacuum

chambers - SO 21 36 V interception solenoid valve - SO DO 40 V

mm 600x1200 with 2 independent chambers - SO 60 120 X

9.36
SPECIAL OCTOPUS GRIPPING SYSTEM PRODUCTS

3D drawings are available on vuototecnica.net

mm 620x1240 with 12 independent chambers - SO 62 127 2V

9.37
SPECIAL OCTOPUS GRIPPING SYSTEM PRODUCTS WITH 3D PRINTER
3D drawings are available on vuototecnica.net

NOTE: Octopus gripping systems made with 3D printer can be supplied in colours: blue, black, white and red.

9.38
OCTOPUS VACUUM GRIPPING Company
SYSTEM QUESTIONNAIRE
For a correct dimensioning of an octopus vacuum gripping Address
system, it is important to know and assess the features of the
load to be handled.
For this reason, please fill out the following form and send it Post code / City Country

3D drawings are available on vuototecnica.net

back to us via e-mail or fax.
We will suggest the best Octopus to solve your problem.
A drawing of the product to be handled or the product itself Contact person:
would allow us to offer the best solution.
E-mail: [email protected]
Fax: + 39 039 5320015 Telephone Fax

E-mail

1) In which industrial sector would the Octopus be used?

Plastic Wood Glass/Solar Steel sheet

Marble/Stone Ceramic/Baked clay Paper/Cardboard Packaging
Automotive Graphics Pharmaceuticals Food
Cosmetics Bottling Other sectors

2) With what material is the product to be handled made?

Plastic Glass Wood Paper/Cardboard

Steel sheet Marble/Granite Rubber Other

3) What is the surface of the product to be gripped like?

Dry Wet Smooth Rough Creased

Corrugated Flaky Porous Textured Bush-hammered

4) On the gripping surface there may be impurities such as:

Powder Water Oil Solvents Other

5) What is the temperature of the load to be handled?

From - °C to + °C For a short time °C Continuously °C

6) What do you need to pick up?

Description of product:

Other
%

9.39
OCTOPUS VACUUM GRIPPING SYSTEM QUESTIONNAIRE
3D drawings are available on vuototecnica.net

7) What shape is the product to be handled?

Square Rectangular Triangular Round

Irregular Other

8) What are the dimensions and weight of the load?

Sheet / Block Cylinder / Disc Pallets / Tables Beams / Tiles

Size A B H H1 C D ΔH ΔA Weight
Minimum mm mm mm mm mm mm mm mm kg

Maximum mm mm mm mm mm mm mm mm kg

9) On what machine will the Octopus be assembled?

Anthropomorphic robot Cartesian axes portal Other

10) From where will the load be picked up?

From a conveyor belt From a fixed worktop From another machine

11) How will the load be handled?

Vertically Horizontally Both ways

12) In what position will the load to be handled be?

Vertical Horizontal Inclined

9.40
OCTOPUS VACUUM GRIPPING SYSTEM QUESTIONNAIRE

3D drawings are available on vuototecnica.net

13) Is the position of the load always well defined?

Yes No, errors of deviation may occur within: mm

14) What are the maximum acceleration values?

Z-axis acceleration m/s2

Y-axis acceleration m/s2
X-axis acceleration m/s2

15) How is the product picked up?

From above From below From the side

16) What can the maximum overall dimensions of the Octopus gripping system be, related to your needs?

X mm Y mm Z mm
%

9.41
OCTOPUS VACUUM GRIPPING SYSTEM QUESTIONNAIRE
3D drawings are available on vuototecnica.net

17) By what device would you like to generate the vacuum?

Electrical vacuum pump

Pneumatic vacuum generator

If you selected a vacuum pump, indicate the electrical characteristics available:

Electrical power: Single-phase Volt 230 – 50Hz Other Volt Hz

Three-phase Volt 230/400 – 50Hz Other Volt Hz

If you selected a pneumatic vacuum generator, indicate the characteristics of the available compressor:

Installed power kW
Maximum compressed air pressure bar

18) Other technical data required:

Maximum gripping time sec Maximum cycle time sec

19) At which height above sea level is the Octopus system to be installed?

20) What other components must be moved in addition to the product?

Separators Empty pallets Containers Other

For Boxes, containers, vessels and similar, supply:

Relative drawings Layout Gripping arrangement Other

21) Gripping tests on your samples

We can perform tests for gripping and handling on samples of products supplied by you and can send you videos/images relative to tests
performed.

22) Contact

Do you wish to be called back? Yes No

Are you interested in a visit? Yes No If yes, what date/time?

9
%

9.42
GRAPHIC DIVISION

GRAPHIC DIVISION – PRODUCT DESCRIPTION PG. 10.01

TABLE FOR PNEUMATIC PUMP SELECTION PG. 10.02

3D drawings are available on vuototecnica.net

SMALL PNEUMATIC SUCTION PUMPS item PA 3 and PA 7 PG. 10.03
SMALL PNEUMATIC SUCTION PUMPS item PA 10, PA 14 and PA 18 PG. 10.04
SMALL PNEUMATIC SUCTION PUMPS item PA 40, PA 70 and PA 100 PG. 10.05
SMALL PNEUMATIC SUCTION PUMPS item PA 140, PA 170 and PA 200 PG. 10.06
PNEUMATIC SUCTION PUMPS item PA 250 and PA 300 PG. 10.07
SMALL PNEUMATIC BLOWING PUMPS item PS 3 and PS 7 PG. 10.08
SMALL PNEUMATIC BLOWING PUMPS item PS 10, PS 14 and PS 18 PG. 10.09
SMALL PNEUMATIC BLOWING PUMPS item PS 40, PS 70 and PS 100 PG. 10.10
SMALL PNEUMATIC BLOWING PUMPS item PS 140, PS 170 and PS 200 PG. 10.11
PNEUMATIC BLOWING PUMPS item PS 250 and PS 300 PG. 10.12
SMALL COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
item PA 3 ÷ 7 WITH PS 3 ÷ 7 PG. 10.13
item PA 10 ÷ 18 WITH PS 10 ÷ 18 PG. 10.14
COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
item PA 40 ÷ 100 WITH PS 40 ÷ 100 PG. 10.15
item PA 140 ÷ 200 WITH PS 140 ÷ 200 PG. 10.16
item PA 250 ÷ 300 WITH PS 250 ÷ 300 PG. 10.17
SUCTION AND BLOWING SYSTEM AS PG. 10.18
PNEUMATIC SUCTION AND BLOWING PUMP HOLDING SUPPORTS PG. 10.19
PNEUMATIC SUCTION AND BLOWING PUMP SUCTION FILTERS PG. 10.20
PNEUMATIC PUMP SPARE PARTS PG. 10.21 ÷ 10.22
VACUUM CYLINDERS PG. 10.23
DISC CUPS PG. 10.24

10
10
3D drawings are available on vuototecnica.net
GRAPHIC DIVISION

The experience and production capacity of Vuototecnica has originated a division specially dedicated to the graphics and printing sector. A
reference entity, ranging from engineering to services, that offers innovative and advantageous technical solutions under every point of view:
performance, reliability, duration and operational economy. A significant demonstration of the Graphic Division specialisation is represented by
the new range of products among which:

3D drawings are available on vuototecnica.net

PNEUMATIC SUCTION AND BLOWING PUMPS
This new generation of highly versatile multiple-ejector pumps (multi-stage) are able to suction or blow as needed and represent a real
evolution compared to conventional rotary vane pumps. Characterised by their new generation of ejectors, these pumps boast an excellent
ratio between the quantity of air consumed and that suctioned (or generated), benefiting operational consumption. Their level of vacuum (or
pressure level) and flow rate can be adjusted based simply on the air supply pressure. The state of the art hi-tech materials have considerably
reduced the weight allowing them to be installed directly on the machine. The Vuototecnica research centre has focused its attention on noise
reduction, with solutions that provide for full soundproofing and no moving parts, thus prolonging duration and eliminating any vibrations.
Furthermore, these pumps are based on the Venturi principle which exploits the compressed air kinetic energy via in-line ejectors and,
therefore, do not develop heat. The excellent filtration of the compressed air supply and intake air allows the intake of air free from oil, water
condensates and impurities from between the sheets of paper to be separated in the working environment, with no pollution. Other assets
of this safe and competitive technology include a minimal maintenance, limited to a regular filter cleaning operation, and reliability with no
comparison. The pneumatic suction and blowing pumps are described in the following pages.

VACUUM CYLINDERS
By assembling a vacuum cup onto their perforated stem and creating a vacuum, the cup will quickly come into contact with the sheet or the
object to be handled and it will automatically lift it, holding it until the vacuum is excluded. Thanks to all these features, this range of cylinders
combined with cups are particularly recommended for separating sheets of paper or plastic. Advantages include: high speed operation,
automatic compensation of the height of the objects to be lifted, non-rotating stems and extremely easy fixing. These vacuum cylinders are
illustrated and described on the following pages.

VACUUM CUPS
These come in a large variety of shapes and sizes, to guarantee a quick and safe grip and they can be provided in anti-abrasion natural para
rubber, nitrile or oil-resistant rubber, silicone, Viton, polyurethane and other compounds, according to the requirements.
Vacuum cups are described in detail in Chapter 1. This chapter on the other hand will focus on disc cups only.

Low air consumption and lightweight.

Surprising silence and total absence of heat.
Maximum respect for the work environment and minimum maintenance.

10.01
TABLE FOR PNEUMATIC SUCTION PUMP SELECTION
3D drawings are available on vuototecnica.net

Maximum suction Maximum vacuum generated by a corresponding electric pump

flow rate generated
by a corresponding -0.1 bar -0.2 bar -0.3 bar -0.4 bar -0.5 bar -0.6 bar -0.7 bar -0.8 bar
electric pump -10 KPa -20 KPa -30 KPa -40 KPa -50 KPa -60 KPa -70 KPa -80 KPa
10 m3/h PA 40 PA 40 PA 40 PA 40 PA 40 PA 40 PA 40 PA 40
15 m3/h PA 40 PA 40 PA 40 PA 40 PA 40 PA 40 PA 40 PA 70
20 m3/h PA 40 PA 40 PA 40 PA 40 PA 40 PA 40 PA 70 PA 70
25 m3/h PA 40 PA 40 PA 40 PA 40 PA 40 PA 70 PA 70 PA 70
30 m3/h PA 40 PA 40 PA 40 PA 40 PA 70 PA 70 PA 70 PA 100
40 m3/h PA 40 PA 70 PA 70 PA 70 PA 70 PA 100 PA 100 PA 140
60 m3/h PA 70 PA 70 PA 70 PA 70 PA 100 PA 140 PA 140 PA 170
80 m3/h PA 100 PA 100 PA 100 PA 100 PA 140 PA 140 PA 170 PA 200
100 m3/h PA 100 PA 100 PA 100 PA 100 PA 140 PA 170 PA 200 PA 250
120 m3/h PA 140 PA 140 PA 140 PA 140 PA 170 PA 200 PA 250 PA 300
140 m3/h PA 140 PA 140 PA 140 PA 140 PA 200 PA 250 PA 300 -- ---
160 m3/h PA 170 PA 170 PA 170 PA 200 PA 250 PA 300 -- --- -- ---
180 m3/h PA 170 PA 170 PA 200 PA 250 PA 300 -- --- -- --- -- ---
200 m3/h PA 200 PA 200 PA 200 PA 250 PA 300 -- --- -- --- -- ---
250 m3/h PA 250 PA 300 PA 300 PA 300 -- --- -- --- -- --- -- ---
300 m3/h PA 300 PA 300 PA 300 -- --- -- --- -- --- -- --- -- ---
Example: We need to replace an electric pump with a flow rate of 80 m3/h and a residual vacuum of -0.6 bar.
In the table, cross the "80 m3/h" line with the "-0.6 bar" column. At the intersection of the line with the column, you will find that PA 140 will be the ideal pump for replacement.

TABLE FOR PNEUMATIC BLOWING PUMP SELECTION

Maximum blowing Maximum overpressure generated by a corresponding electric pump

flow rate generated
by a corresponding 0.1 bar 0.2 bar 0.3 bar 0.4 bar 0.5 bar 0.6 bar 0.7 bar 0.8 bar
electric pump 10 KPa 20 KPa 30 KPa 40 KPa 50 KPa 60 KPa 70 KPa 80 KPa
25 m3/h PS 40 PS 40 PS 40 PS 40 PS 40 PS 40 PS 40 PS 40
30 m3/h PS 40 PS 40 PS 40 PS 40 PS 40 PS 40 PS 40 PS 40
40 m3/h PS 40 PS 40 PS 40 PS 40 PS 40 PS 40 PS 40 PS 40
60 m3/h PS 70 PS 70 PS 70 PS 70 PS 70 PS 70 PS 70 PS 70
80 m3/h PS 70 PS 70 PS 70 PS 70 PS 70 PS 70 PS 70 PS 70
100 m3/h PS 70 PS 70 PS 70 PS 70 PS 70 PS 70 PS 100 PS 100
120 m3/h PS 100 PS 100 PS 100 PS 100 PS 100 PS 100 PS 100 PS 100
140 m3/h PS 100 PS 100 PS 100 PS 100 PS 100 PS 100 PS 100 PS 140
160 m3/h PS 140 PS 140 PS 140 PS 140 PS 140 PS 140 PS 140 PS 140
180 m3/h PS 140 PS 140 PS 140 PS 140 PS 140 PS 140 PS 140 PS 140
200 m3/h PS 140 PS 140 PS 140 PS 140 PS 140 PS 140 PS 170 PS 170
250 m3/h PS 200 PS 200 PS 200 PS 200 PS 200 PS 250 PS 250 PS 250
300 m3/h PS 250 PS 250 PS 250 PS 250 PS 250 PS 300 PS 300 PS 300
350 m3/h PS 300 PS 300 PS 300 PS 300 PS 300 PS 300 PS 300 PS 300
400 m3/h PS 300 PS 300 PS 300 PS 300 PS 300 PS 300 -- --- -- ---
10
Example: We need to replace an electric pump with a flow rate of 80 m3/h and an overpressure of 0.6 bar.
In the table, cross the "80 m3/h" line with the "0.6 bar" column. At the intersection of the line with the column, you will find that PS 70 will be the ideal pump for replacement.

10.02
SMALL PNEUMATIC SUCTION PUMPS PA

The assembly of a pressure adjuster equipped with pressure gauge and of an FCL filter
on the suction inlet connection of a vacuum generator of the M .. SSX range has allowed
creating these small pneumatic suction pumps. Their main features include reduced
overall dimensions compared to their technical performance.

3D drawings are available on vuototecnica.net

The level of vacuum and flow rate can be adjusted according to the supply air
pressure.
These pumps are powered with compressed air with a pressure ranging from 1 to
5 bar and they can produce a maximum vacuum of 85% and a suction flow rate
between 2 and 18 m3/h, measured at a normal atmospheric pressure of 1013 mbar.
Based on the Venturi principle, they do not develop heat.
An SSX silencer screwed onto the pump exhaust ensures a silent operation.
The filter equipped with a microporous cartridge is located on the suction inlet
connection and can keep the finest dust and impurities.
Thanks to their static operating principle, maintenance is reduced to only a simple
regular cleaning of the filter.

Compressed air connection

Vacuum connection
For Ø 6 ext. hose

Item PA 3
Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85
Air consumption Nl/s 0.2 0.4 0.5 0.7 0.8
Intake air flow rate m3/h 2.0 2.5 3.0 3.4 3.6
A 88
B 110.5
R Ø G1/4”
Weight Kg 0.45
Item PA 7
Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85
Air consumption Nl/s 0.4 0.6 0.8 1.2 1.4
Intake air flow rate m3/h 3.0 4.0 5.4 5.8 6.2
A 89
B 111.5
R G3/8” 10
Weight Kg 0.46

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.03
SMALL PNEUMATIC SUCTION PUMPS PA 10, PA 14 and PA 18
3D drawings are available on vuototecnica.net

Compressed air connection

For Ø 6 ext. hose

connection
Vacuum
Item PA 10
Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85
Air consumption Nl/s 0.5 0.9 1.2 1.6 1.9
Intake air flow rate m3/h 4.0 6.0 7.7 8.5 9.4
A 94
B 118.5
C 24.5
Weight Kg 0.59
Item PA 14
Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85
Air consumption Nl/s 0.9 1.3 1.7 2.1 2.5
Intake air flow rate m3/h 6.0 8.0 10.2 11.5 12.6
A 94
B 118.5
C 24.5
Weight Kg 0.60
Item PA 18
Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85
Air consumption Nl/s 1.2 1.7 2.3 2.9 3.6
Intake air flow rate m3/h 8.0 11.5 14.8 16.5 18.0
A 102
B 128.5
10 C 34.5
Weight Kg 0.62

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.04
PNEUMATIC SUCTION PUMPS PA

A newly designed range of ejectors has allowed creating this range of pneumatic suction pumps featuring an
excellent ratio between the amount of consumed air and sucked air, as well as the ability to adjust the level of
vacuum and flow rate according to the supply air pressure.
These pumps are powered with compressed air with a pressure ranging from 1 to 6 bar and they can produce a

3D drawings are available on vuototecnica.net

maximum vacuum of 90% and a suction flow rate between 15 and 320 m3/h, measured at a normal atmospheric
pressure of 1013 mbar.
When designing these pumps, our attention was focused on noise. In fact, they are perfectly soundproofed and
there are no moving parts subject to wear and vibrations. All this results in an extremely silent operation. Moreover,
as they are based on the Venturi principle, they do not develop heat.
They are equipped as standard with a filter/pressure reducer unit for the supply air and a filter with
microporous cartridge located on the suction inlet connection which can keep the finest dust and impurities.
The excellent compressed air and sucked air filtration allows blowing air free from oil vapours, water
condensation and impurities in the work environment, causing no pollution. The use of light alloys for making
these pumps has allowed a considerable reduction of their weight thus allowing them to be directly installed
onto the machine.
Thanks to their static operating principle, maintenance is reduced to a only a simple regular cleaning of the filters.
Compressed air connection

connection
Vacuum
For Ø 12 ext. hose

Item PA40
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 14 30 46 65 82 90
Air consumption Nl/s 1.0 1.5 2.0 2.3 2.7 3.2
Intake air flow rate m3/h 15 23 30 36 39 42
Weight Kg 6.2
Item PA70
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 14 30 46 65 82 90
Air consumption Nl/s 2.0 3.0 4.1 4.9 5.7 6.6
Intake air flow rate m3/h 29 47 58 65 73 80
Weight Kg 6.2
Item PA100
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 11 28 45 65 82 90
Air consumption Nl/s 3.0 4.6 6.2 7.2 8.5 9.8
Intake air flow rate m3/h 28 57 75 88 98 108 10
Weight Kg 6.2

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.05
PNEUMATIC SUCTION PUMPS PA 140, PA 170 and PA 200
3D drawings are available on vuototecnica.net

connection
Vacuum
Compressed air connection
For Ø 15 ext. hose

Item PA 140
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90
Air consumption Nl/s 4.1 6.2 8.3 9.6 11.4 13.0
Intake air flow rate m3/h 45 80 106 125 140 152
Weight Kg 7.2
Item PA 170
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90
Air consumption Nl/s 5.1 7.7 10.3 12.1 14.2 16.3
Intake air flow rate m3/h 53 98 128 150 168 182
Weight Kg 7.2
Item PA 200
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90
Air consumption Nl/s 6.0 9.1 12.2 14.2 16.9 19.4
10 Intake air flow rate m3/h 60 110 142 170 188 200
Weight Kg 7.2

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.06
PNEUMATIC SUCTION PUMPS PA 250 and PA 300

3D drawings are available on vuototecnica.net

connection
Vacuum
Compressed air connection
For Ø 15 ext. hose

Item PA250
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90
Air consumption Nl/s 7.5 11.2 15.0 17.3 20.7 24.0
Intake air flow rate m3/h 100 145 190 224 252 280
Weight Kg 8,1
Item PA300
Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90
Air consumption Nl/s 9.0 13.5 18.1 20.4 24.8 29.0
Intake air flow rate m3/h 106 160 213 240 290 320 10
Weight Kg 8.1

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.07
SMALL PNEUMATIC BLOWING PUMPS PS

The pressure and flow rate can be adjusted according to the supply air pressure.
These pumps are powered with compressed air with a pressure ranging from 1 to 5 bar
and can produce a maximum pressure of 0.7 bar and a blowing flow rate between
2.7 and 31 m3/h, measured at a normal atmospheric pressure of 1013 mbar.
Based on the Venturi principle, they do not develop heat.
The filter equipped with microporous cartridge located on the air inlet connection can
keep the finest dust and impurities.
Thanks to their static operating principle, maintenance is reduced to only a simple
regular cleaning of the filter.

Compressed air
connection

For Ø 6 ext. hose

connection
Blowing

Item PS 3
Supply pressure bar 1 2 3 4 5
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.2 0.4 0.5 0.7 0.8
Blown air flow rate m3/h 2.7 3.9 4.8 5.9 6.5
A 88
B 110.5
R Ø G1/4”
Weight Kg 0.44
Item PS 7
Supply pressure bar 1 2 3 4 5
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.4 0.6 0.8 1.2 1.4
Blown air flow rate m3/h 4.4 6.1 8.2 10.1 11.2
A 89
B 111.5
10 R G3/8”
Weight Kg 0.45

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.08
SMALL PNEUMATIC BLOWING PUMPS PS 10, PS 14 and PS 18

3D drawings are available on vuototecnica.net

Compressed air
connection

For Ø 6 ext. hose

connection
Blowing

Item PS 10
Supply pressure bar 1 2 3 4 5
Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.5 0.9 1.2 1.6 1.9
Blown air flow rate m3/h 5.8 9.2 12.0 14.2 16.2
A 94
B 118.5
C 24.5
R G3/8”
Weight Kg 0.49
Item PS 14
Supply pressure bar 1 2 3 4 5
Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.9 1.3 1.7 2.1 2.5
Blown air flow rate m3/h 9.2 12.6 16.3 19.0 21.6
A 94
B 118.5
C 24.5
R G3/8”
Weight Kg 0.50
Item PS 18
Supply pressure bar 1 2 3 4 5
Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 1.2 1.7 2.3 2.9 3.6
Blown air flow rate m3/h 12.3 17.6 23.0 26.9 31.0
A 94
B 128.5
C 34.5
R G1/2” 10
Weight Kg 0.52

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.09
PNEUMATIC BLOWING PUMPS PS

A newly designed range of ejectors has allowed creating this range of pneumatic blowing
pumps featuring an excellent ratio between the amount of consumed air and generated air, as
well as the ability to adjust the pressure and flow rate according to the supply air pressure.
These pumps are powered with compressed air with a pressure ranging from 1 to 6 bar and
3D drawings are available on vuototecnica.net

have a blowing flow rate between 18 and 425 m3/h, measured at a normal atmospheric
pressure of 1013 mbar.
When designing these pumps, our attention was focused on noise. In fact, they are perfectly
soundproofed and there are no moving parts subject to wear and vibrations. All this results in
an extremely silent operation.
Moreover, as they are based on the Venturi principle, they do not develop heat.
They are equipped as standard with a filter/pressure reducer unit for the supply air and a filter
with microporous cartridge located on the air inlet connection which can keep the finest dust
and impurities.
The excellent filtration of the compressed air supply and intake air allows the intake of air free
from oil, water condensates or impurities from between the sheets of paper to be separated in
the working environment, with no pollution.
The use of light alloys for making these pumps has allowed a considerable reduction of their
weight thus allowing them to be directly installed onto the machine.
Thanks to their static operating principle, maintenance is reduced to a only a simple regular
cleaning of the filters.
connection
Blowing

Compressed air connection

For Ø 12 ext. hose

Item PS 40
Supply pressure bar 1 2 3 4 5 6
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 1.0 1.5 2.0 2.3 2.7 3.2
Blown air flow rate m3/h 18 28 37 44 48 53
Weight Kg 6.3
Item PS 70
Supply pressure bar 1 2 3 4 5 6
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 2.0 3.0 4.1 4.9 5.7 6.6
Blown air flow rate m3/h 36 57 72 83 93 104
Weight Kg 6.3
Item PS 100
Supply pressure bar 1 2 3 4 5 6
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
10 Air consumption Nl/s 3.0 4.6 6.2 7.2 8.5 9.8
Blown air flow rate m3/h 38 73 97 114 129 144
Weight Kg 6.3

Operating temperature °C -20 / +80

NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.10
PNEUMATIC BLOWING PUMPS PS 140, PS 170 and PS 200

3D drawings are available on vuototecnica.net

connection
Blowing

Compressed air connection

For Ø 15 ext. hose

Item PS 140
Supply pressure bar 1 2 3 4 5 6
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 4.1 6.2 8.3 9.6 11.4 13.0
Blown air flow rate m3/h 59 102 135 160 181 199
Weight Kg 7.3
Item PS 170
Supply pressure bar 1 2 3 4 5 6
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 5.1 7.7 10.3 12.1 14.2 16.3
Blown air flow rate m3/h 71 125 165 194 219 240
Weight Kg 7.3
Item PS 200
Supply pressure bar 1 2 3 4 5 6
Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 6.0 9.1 12.2 14.2 16.9 19.4 10
Blown air flow rate m3/h 81 142 185 221 249 270
Weight Kg 7.3

Operating temperature °C -20 / +80

NOTE: All vacuum values indicated in the table are valid at the normal atmospheric pressure of 1013 mbar and obtained with a constant supply pressure.
Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.11
PNEUMATIC BLOWING PUMPS PS 250 and PS 300
3D drawings are available on vuototecnica.net

connection
Blowing

Compressed air connection

For Ø 15 ext. hose

Item PS 250

Supply pressure bar 1 2 3 4 5 6

Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 7.5 11.2 15.0 17.3 20.7 24.0
Blown air flow rate m3/h 127 185 244 286 327 366
Weight Kg 8.2

Item PS 300

Supply pressure bar 1 2 3 4 5 6

Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 9.0 13.5 18.1 20.4 24.8 29.0
10 Blown air flow rate m3/h 138 208 278 313 379 424
Weight Kg 8.2

Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.12
SMALL COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
PA 3 ÷ 7 WITH PS 3 ÷ 7
All the small pneumatic suction and blowing pumps
previously described can be combined regardless of
their suction or blowing flow rate.
Given the enormous number of possible

3D drawings are available on vuototecnica.net

combinations, for space reasons, this catalogue
only describes combinations of pumps with the
same size.

Compressed air Compressed air

connection connection

For Ø 6 ext. hose

Vacuum
connection

Blowing
connection

Item PA 3 Item PS 3
Supply pressure bar 1 2 3 4 5 Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85 Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.2 0.4 0.5 0.7 0.8 Air consumption Nl/s 0.2 0.4 0.5 0.7 0.8
Intake air flow rate m3/h 2.0 2.5 3.0 3.4 3.6 Blown air flow rate m3/h 2.7 3.9 4.8 5.9 6.5
A 88 A 88
B 110.5 B 110.5
R Ø G1/4” R Ø G1/4”
Weight Kg 0.45 Weight Kg 0.44
Item PA 7 Item PS 7
Supply pressure bar 1 2 3 4 5 Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85 Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.4 0.6 0.8 1.2 1.4 Air consumption Nl/s 0.4 0.6 0.8 1.2 1.4
Intake air flow rate m3/h 3.0 4.0 5.4 5.8 6.2 Blown air flow rate m3/h 4.4 6.1 8.2 10.1 11.2
A 88 A 88
B 110.5 B 110.5
R Ø G3/8” R Ø G3/8” 10
Weight Kg 0.46 Weight Kg 0.45

Operating temperature °C -20 / +80 Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.13
SMALL COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
PA 10 ÷ 18 WITH PS 10 ÷ 18
3D drawings are available on vuototecnica.net

Compressed air Compressed air

connection connection

For Ø 6 ext. hose

Vacuum
connection

Blowing
connection

Item PA 10 Item PS 10
Supply pressure bar 1 2 3 4 5 Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85 Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.5 0.9 1.2 1.6 1.9 Air consumption Nl/s 0.5 0.9 1.2 1.6 1.9
Intake air flow rate m3/h 4.0 6.0 7.7 8.5 9.4 Blown air flow rate m3/h 5.8 9.2 12.0 14.2 16.2
A 94 A 94
B 118.5 B 118.5
C 24.5 C 24.5
R Ø G3/8”
Weight Kg 0.59 Weight Kg 0.49
Item PA 14 Item PS 14
Supply pressure bar 1 2 3 4 5 Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85 Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 0.9 1.3 1.7 2.1 2.5 Air consumption Nl/s 0.9 1.3 1.7 2.1 2.5
Intake air flow rate m3/h 6.0 8.0 10.2 11.5 12.6 Blown air flow rate m3/h 9.2 12.6 16.3 19.0 21.6
A 94 A 94
B 118.5 B 118.5
C 24.5 C 24.5
R Ø G3/8”
Weight Kg 0.60 Weight Kg 0.50
Item PA 18 Item PS 18
Supply pressure bar 1 2 3 4 5 Supply pressure bar 1 2 3 4 5
Maximum level of vacuum -KPa 20 42 62 80 85 Maximum blowing pressure bar 0.1 0.2 0.3 0.5 0.7
Air consumption Nl/s 1.2 1.7 2.3 2.9 3.6 Air consumption Nl/s 1.2 1.7 2.3 2.9 3.6
Intake air flow rate m3/h 8.0 11.5 14.8 16.5 18.0 Blown air flow rate m3/h 12.3 17.6 23.0 26.9 31.0
A 94 A 94
B 136.5 B 128.5
C 34.5 C 34.5
10 R Ø G1/2”
Weight Kg 0.62 Weight Kg 0.52

Operating temperature °C -20 / +80 Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.14
COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
PA 40 ÷ 100 WITH PS 40 ÷ 100
All the pneumatic suction and blowing pumps previously described
can be combined regardless of their suction or blowing flow rate.
Given the enormous number of possible combinations, for space
reasons, this catalogue only describes combinations of pumps with

3D drawings are available on vuototecnica.net

the same size.

Blowing
connection
Compressed air

connection
Compressed air

Vacuum
connection

connection
For Ø 12 ext. hose
For Ø 12 ext. hose

Item PA 40 Item PS 40
Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 14 30 46 65 82 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 1.0 1.5 2.0 2.3 2.7 3.2 Air consumption Nl/s 1.0 1.5 2.0 2.3 2.7 3.2
Intake air flow rate m3/h 15 23 30 36 39 42 Blown air flow rate m3/h 18 28 37 44 48 53
Weight Kg 6.2 Weight Kg 6.3
Item PA 70 Item PS 70
Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 14 30 46 65 82 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 2.0 3.0 4.1 4.9 5.7 6.6 Air consumption Nl/s 2.0 3.0 4.1 4.9 5.7 6.6
Intake air flow rate m3/h 29 47 58 65 73 80 Blown air flow rate m3/h 36 57 72 83 93 104
Weight Kg 6.2 Weight Kg 6.3
Item PA 100 Item PS 100
Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 14 30 46 65 82 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 3.0 4.6 6.2 7.2 8.5 9.8 Air consumption Nl/s 3.0 4.6 6.2 7.2 8.5 9.8
Intake air flow rate m3/h 28 57 75 88 98 108 Blown air flow rate m3/h 38 73 97 114 129 144
10
Weight Kg 6.2 Weight Kg 6.3

Operating temperature °C -20 / +80 Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.15
COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
PA 140 ÷ 200 WITH PS 140 ÷ 200
3D drawings are available on vuototecnica.net

Blowing
connection

connection
Vacuum
Compressed air

Compressed air
connection

connection
For Ø 15 ext. hose

For Ø 15 ext. hose

Item PA 140 Item PS 140

Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 4.1 6.2 8.3 9.6 11.4 13.0 Air consumption Nl/s 4.1 6.2 8.3 9.6 11.4 13.0
Intake air flow rate m3/h 45 80 106 125 140 152 Blown air flow rate m3/h 59 102 135 160 181 199
Weight Kg 7.2 Weight Kg 7.3
Item PA 170 Item PS 170
Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 5.1 7.7 10.3 12.1 14.2 16.3 Air consumption Nl/s 5.1 7.7 10.3 12.1 14.2 16.3
Intake air flow rate m3/h 53 98 128 150 168 182 Blown air flow rate m3/h 71 125 165 194 219 240
Weight Kg 7.2 Weight Kg 7.3
Item PA 200 Item PS 200
Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 6.0 9.1 12.2 14.2 16.9 19.4 Air consumption Nl/s 6.0 9.1 12.2 14.2 16.9 19.4
10 Intake air flow rate m3/h 60 110 142 170 188 200 Blown air flow rate m3/h 81 142 185 221 249 270
Weight Kg 7.2 Weight Kg 7.3

Operating temperature °C -20 / +80 Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.16
COMBINED PNEUMATIC SUCTION PUMPS PA AND BLOWING PUMPS PS
PA 250 ÷ 300 WITH PS 250 ÷ 300

3D drawings are available on vuototecnica.net

Blowing
connection

connection
Vacuum
Compressed air

Compressed air
connection

connection
For Ø 15 ext. hose

For Ø 15 ext. hose

Item PA 250 Item PS 250

Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 7.5 11.2 15.0 17.3 20.7 24.0 Air consumption Nl/s 7.5 11.2 15.0 17.3 20.7 24.0
Intake air flow rate m3/h 100 145 190 224 252 280 Blown air flow rate m3/h 127 185 244 286 327 366
Weight Kg 8.1 Weight Kg 8.2
Item PA 300 Item PS 300
Supply pressure bar 1 2 3 4 5 6 Supply pressure bar 1 2 3 4 5 6
Maximum level of vacuum -KPa 15 35 55 70 85 90 Maximum blowing pressure -KPa 0.1 0.2 0.3 0.5 0.7 0.8
Air consumption Nl/s 9.0 13.5 18.1 20.4 24.8 29.0 Air consumption Nl/s 9.0 13.5 18.1 20.4 24.8 29.0
Intake air flow rate m3/h 106 160 213 240 290 320 Blown air flow rate m3/h 138 208 278 313 379 424
10
Weight Kg 8.1 Weight Kg 8.2

Operating temperature °C -20 / +80 Operating temperature °C -20 / +80

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.17
SUCTION AND BLOWING SYSTEM AS

With the suction and blowing system AS, we have tried to provide the printing industry with an answer to most of their requirements regarding
the management of paper during the printing process, or rather:
- The concentration of all the necessary pumps and commands on one single piece.
- An increased printing quality thanks to individually controlled pumps.
3D drawings are available on vuototecnica.net

- An increase of productivity resulting from the configuration and use of individual pumps.
- Reduced machine idle state due to the pneumatic pumps based on the Venturi principle.
- An improvement of the work environment thanks to the noise reduction, absence of heat and the emission of air free of oil vapours, water
condensation and impurities between the sheets of paper to be separated and in the work environment.
- Energy saving due to a low compressed air consumption compared to the amount of
sucked (or generated) air.
- Maintenance reduced to a regular cleaning of the filters.
The suction and blowing system AS is composed of a metal, easy-to-place cabinet, inside of
which the combined pneumatic pumps PA and PS are located with the supply compressed air
interception and adjustment valves.
The suction and blowing capacities of the pumps are determined according to the client’s
requirements or to technical specifications of the machine manufacturer.
The blowing and suction connectors are located on the sides of the cabinet for the connection to
the application, as well as the filters equipped with micro-porous cartridge against fine dust.
The following are installed on the control panel:
- The pneumatic main switch for supply compressed air interception with a pressure gauge
for a direct reading of the line pressure.
- The pneumatic switches for supply compressed air interception of every single pump.
- The pressure reducers with relative pressure gauges for adjusting the compressed air of
every single pump. The vacuum (or pressure) level as well as the pump flow rate can be
adjusted according to the supply air pressure.
- Vacuum gauges and pressure gauges for a direct reading of the vacuum and pressure at
the application.
- Vacuum gauges for controlling the clogging level of the PS pump filters.
All our pneumatic suction and blowing pumps can be combined regardless of their suction
and blowing flow rate and can be installed inside the system cabinet. Given the enormous
number of possible combinations, this catalogue only describes combinations of pumps
with the same size.

Fitted for: Weight

Item
Kg
AS 4 4 PA / PS pumps 120
NOTE: The filters are not parts built into the system, but they are the same filters installed on the PA / PS pumps, carried outside the cabinet.
10 To order the complete system, simply add the item of the selected PA and PS pumps to item AS 4.
Example: 1 AS 4
1 PA 100 1 PS 140
1 PA 170 1 PS 200
It is possible to install maximum 4 pumps on the system, regardless of their size and suction or blowing function.
NOTE: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
10.18
PNEUMATIC SUCTION AND BLOWING PUMP HOLDING SUPPORTS

The supports described on this page have been designed to allow a

quick assembly of the pneumatic suction and blowing pumps and
their easy placement on the machine.
They are made with a sturdy, satin-finished, stainless sheet steel and

3D drawings are available on vuototecnica.net

are equipped with anti-slip and anti-vibration rubber feet.
These supports are currently available for single pneumatic pumps
and for the combined ones.

SUPPORT FOR SMALL COMBINED PNEUMATIC PUMPS

Rubber feet

A B C D E F G H I L M N O P Q Weight
Item
Ø Ø Kg
GR DIV 03 100 39.5 3.75 64 12 11.5 74.5 13.5 41 43 84 47.5 79 4.5 45° 0.1

SUPPORT FOR SINGLE PNEUMATIC PUMPS

Rubber feet

SUPPORT FOR COMBINED PNEUMATIC PUMPS

Rubber feet

10
A B C D E F G H I L M N O P Q Weight
Item
Ø Ø Kg
GR DIV 01 140 120 10 270 15 30 80 10 264 81 355 170 250 8.5 45° 2.1
GR DIV 02 284 132 10 270 15 30 224 10 264 81 355 170 250 8.5 45° 4.2

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
10.19
PNEUMATIC SUCTION AND BLOWING PUMP SUCTION FILTERS

To allow the pneumatic suction and blowing pumps to work even in very dusty
environments, it is necessary to use these filters that, installed on the suction inlet
connection, can keep the finest dust and impurities and affecting the flow rate in a
negligible manner.
3D drawings are available on vuototecnica.net

The filtering cartridges, in fact, are made with a special treated paper with a porosity
level of 5 - 7 micron, and pleated to increase the filtering surface.
FCL filters are composed of a transparent Plexiglass cylindrical body inside of which is
located the filtering cartridge locked by two anodised aluminium flanges that are kept in
place by Seeger rings, inside of which the threaded connectors and the seals are housed.
The filters can be inspected by simply removing one of the two flanges.
The container of the filtering element FP is made with plastic and it is screwed onto the
blue plastic lid; a gasket located between the two elements ensures a perfect seal.
The container of the filtering element FC, as well as its lid, are made with sheet steel
and varnished with a special oxidation-resistant treatment. A seal between the lid and
the container ensures a perfect vacuum seal, while the release clamps on the container
allow a quick opening of the lid to check or replace the filtering cartridge.

d A B C D E F Max capac. For pumps Weight Spare cartridge

Item
Ø Ø m3/h item Kg item
FCL 1 MF G1/4” 91.2 20 17 19.1 12 7.1 5 PA - PS 3 0.12 00 FCL 03
FCL 2 MF G3/8” 93.4 24 20 19.1 12 9.3 20 PA - PS 7 - 14 - 18 0.14 00 FCL 03

Item FC 38
Item FP 30 / 4 / SP Item FC 55

10
d A B C D Max capac. For pumps Weight Spare cartridge
Item
Ø Ø m3/h item Kg item
FP 30/4/SP G1” 145 169 24 130 100 PA - PS 40 ÷ 100 1.00 SP/4
FC 38 G1” 1/2 143 101 45 120 200 PA - PS 140 ÷ 200 0.95 00 FC 15
FC 55 G2” 143 170 79 120 300 PA - PS 250 ÷ 300 1.29 00 FC 33

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
10.20
PNEUMATIC PUMP SPARE PARTS

3D drawings are available on vuototecnica.net

Vacuum gauge Ø 40 mm with 1/8” coaxial gas coupler

Item For pneumatic pumps

09 03 15 PA - PS 40 ÷ 300

Pressure gauge Ø 40 mm with 1/8” coaxial gas coupler

Item bar For pneumatic pumps

09 03 25 1 ÷ 10 All
09 03 20 1 ÷ 1.6 PS 40 ÷ 300

1/8” gas pressure reducer

Item For pneumatic pumps

FIR 00 SF PA 3 - 7 - 10 - 14 - 18
PS 3 - 7 - 10 - 14 - 18

1/2” gas filter/pressure reducer

Item For pneumatic pumps

FIR 03 PA 40 - 70 - 100 - 140 - 170 - 200 - 250 - 300
PS 40 - 70 - 100 - 140 - 170 - 200 - 250 - 300

10.21
PNEUMATIC PUMP SPARE PARTS

Sealing kit and reed valves

3D drawings are available on vuototecnica.net

Item For pneumatic pumps item

00 KIT M 3 PA 3 - PS 3
00 KIT M 7 PA 7 - PS 7
00 KIT M 10 PA 10 - PS 10
00 KIT M 14 PA 14 - PS 14
00 KIT M 18 PA 18 - PS 18

Sealing kit and reed valves

Item For pneumatic pumps item

00 KIT PVP 40 M PA 40 - PS 40
00 KIT PVP 70 M PA 70 - PS 70
00 KIT PVP 100 M PA 100 - PS 100
00 KIT PVP 140 M PA 140 - PS 140
00 KIT PVP 170 M PA 170 - PS 170
00 KIT PVP 200 M PA 200 - PS 200
00 KIT PVP 250 M PA 250 - PS 250
00 KIT PVP 300 M PA 300 - PS 300

Exhaust silencers SSX

Item For pneumatic pumps

SSX 1/4” PA 3
SSX 3/8” PA 7 - 10 - 14
SSX 1/2” PA 18

Sound absorbing material on the exhaust

Item For pneumatic pumps item Quantity

00 15 110 PA 40 - PS 40 1 piece
PA 70 - PS 70 1 piece
PA 100 - PS 100 1 piece
PA 140 - PS 140 1 piece
PA 170 - PS 170 1 piece
PA 200 - PS 200 1 piece
PA 250 - PS 250 1 piece
PA 300 - PS 300 1 piece

Sound absorbing material on ejectors

Item For pneumatic pumps item Quantity

00 15 111 PA 40 - PS 40 1 piece
PA 70 - PS 70 1 piece
10 PA 100 - PS 100 1 piece
PA 140 - PS 140 2 pieces
PA 170 - PS 170 2 pieces
PA 200 - PS 200 2 pieces
PA 250 - PS 250 3 pieces
PA 300 - PS 300 3 pieces

10.22
VACUUM CYLINDERS

The cylinders described on this page are vacuum operated.

By creating a vacuum in the anterior chamber of the cylinder, the
piston's integrated rod protrudes, overcoming the opposing spring force.
The piston is pushed by the air at atmospheric pressure that gets into

3D drawings are available on vuototecnica.net

the cylinder’s rear chamber through the hollow stem.
The greater the pressure differential between the front chamber under
vacuum and the rear chamber at atmospheric pressure, and the larger
the piston thrust force will be.
The stem returns into position in two ways:
1) By preventing the atmospheric air from entering through the stem
hole and with the vacuum inserted, the pressure differential inside the
cylinder is removed. Under this condition, the thrust spring and the
atmospheric pressure forces prevail on the stem which is thus pushed
into its initial position.
2) By excluding the vacuum, the atmospheric pressure is restored
in both the cylinder chambers. Also in this case, being the pressure
differential removed, the stem returns to its initial position pushed by
the thrust spring.
The first of these two methods is the true operating principle for which
this cylinder has been designed. When a vacuum is created, in fact, a
vacuum cup mounted on the stem of the perforated cylinder will be
brought rapidly into contact with the object to be taken. The object is
then automatically lifted and remain gripped during the whole time the
vacuum stays engaged.
Because of this feature, vacuum cylinders associated with vacuum

For Ø E internal hose

cups are recommended for gripping and handling machined, moulded
or thermoformed objects, as well as for separating sheets of paper or
plastic, sheet steel, etc. and lifting printed circuits or thin plastic panels.
The advantages offered by these vacuum cylinders include: short,
fast quick cycles controlled by a single vacuum interception valve,
automatic compensation of the height of the objects to be gripped
with no compression on them, non-rotating piston and extremely easy
fixing.
Vacuum connection
They are fully made with anodised aluminium and are equipped with
a special self-lubricating technopolymer bush which guarantees long Sp.1

duration. Sp.2

Sp.3
stroke

Use this spanner housing

Caution: as a constrast during
during the vacuum cup assembly phase, use the wr.3 seat as a contrast and not the wr.1 seat to vacuum cup assembly
avoid damaging the product.

Item 25 05 10 25 10 10 25 15 10
Stroke mm 17 25 30
Thrust force at -KPa 80 Kg 2.0 4.3 12.0
Lifting force at -KPa 80 Kg 0.45 1.0 2.5
Minimum cycle time sec 0.3 0.4 0.6
Minimum level of vacuum -KPa 60 60 60
Minimum necessary flow rate Nl/1’ 15 30 90
Operating temperature °C 5 ÷ 80 5 ÷ 80 5 ÷ 80
Weight g 55 145 515
A Ø 24 35 59
B Ø M6 G1/8” M 10
C Ø M5 G1/8” G1/4”
D Ø M 16 x 1.5 M 22 x 1.5 M 40 x 1.5
E Vacuum connection by tube Ø int. 4 4 4
F 39.5 56 66
G 12 16 17
H 4 6 9 10
I 55.5 78 92
wr. 1 19 27 50
wr. 2 24 32 55
wr. 3 8 12 17

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = = Adapters for GAS - NPT threading available on page 1.130
25.4 453.6 0.4536
10.23
DISC CUPS

Apart from some standard rubber discs, these items are generally produced upon
specific request by the client and for a minimum amount to be specified in the offer
phase.
They can be die-cut from sheets or moulded in nitrile rubber, in natural para rubber,
3D drawings are available on vuototecnica.net

silicone or special compounds, as well as in rubberised or polyurethane fabric.

The discs described above are used in the printing industry, as an alternative to vacuum
cups, for gripping and handling sheets of paper, cardboard or plastic.

screw not supplied disc vacuum cup

EXAMPLE OF APPLICATION

D d S
Item
Ø Ø
01 17 31 N 17 3.5 0.8
01 30 41 NG 30 4.0 1.5
10 01 30 91 N 30 9.0 1.5
01 57 81 S 57 8.5 1.3
N = natural para rubber; NG= yellow rubber; S = silicone

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
10.24
SPECIAL PRODUCTS

DEGASIFIERS PG. 11.01

MOBILE SYSTEM FOR RESIN VACUUM INFUSION PG. 11.02

3D drawings are available on vuototecnica.net

ELECTRICAL EQUIPMENT FOR VACUUM TESTS PG. 11.03
PNEUMATIC EQUIPMENT FOR VACUUM TESTS PG. 11.04
SUCTION UNITS WITH SYPHON FILTER GA FS 5 and GA FS 10 PG. 11.05
SUCTION UNITS WITH SYPHON FILTER GA FS 20 ES - GA FS 30 ES PG. 11.06
SAFETY SUCTION UNITS WITH SYPHON FILTER PG. 11.07
LIQUID-SUCKING PUMP SETS PG. 11.08
SAMPLES AND EQUIPMENT FOR DEMONSTRATION USE PG. 11.09 ÷ 11.12

11
11
3D drawings are available on vuototecnica.net
DEGASIFIERS

The function of degasifiers is to suck the air bubbles that remain in the synthetic resin or
composite material mixes and in silicone or similar compounds during their preparation.
The presence of bubbles, in fact causes a drastic reduction of their technical features
and negatively affects their appearance.

3D drawings are available on vuototecnica.net

Degasifiers are composed of:
- One or two welded sheet steel autoclaves, featuring a perfect vacuum seal,
equipped with transparent methacrylate lids that can be manually removed.
- An oil-bath rotating vane pump for high vacuum.
- One or two vacuum switches for a direct reading of the level of vacuum in the
autoclave.
- One or two three-way manual valves for vacuum interception.
- A switchgear enclosed in a special protective casing.
- A profiled steel frame for assembling all the components.
Inside the autoclave, the degasifiers can reach a final level of vacuum equal to
99.5 %. With small modifications and with the aid of insulating or waterproofing
resins these degasifiers can be used for vacuum-impregnating windings for
electric motors, transformers, electric coils, etc.
Upon request they can also be supplied in different versions.

Vacuum interception valve Vacuum gauge 09 03 10 Switchgear

Vacuum
pump
100-litre
autoclave

Liquid
discharge cap

Vacuum interception valve Vacuum gauge 09 03 10 Switchgear Vacuum gauge 09 03 10

Vacuum
pump
100-litre
autoclave
50-litre
autoclave

Liquid Liquid
discharge cap discharge cap

Autoclaves Pump Motor performance Motor power Switchgear A Weight

Item
Litres mod. Volt Kw item Kg
DR 100 01 100 RVP 21 3 ~ 230/400-50Hz 0.75 DR 100 90 1100 62.0
DR 100 02 100 RVP 40 3 ~ 230/400-50Hz 1.10 DR 100 90 1100 85.5
D2R 150 01 100+50 RVP 21 3 ~ 230/400-50Hz 0.75 DR 100 90 1600 82.0
D2R 150 02 100+50 RVP 40 3 ~ 230/400-50Hz 1.10 DR 100 90 1600 105.5 11
NOTE: The vacuum gauges installed can be supplied with an Accredia calibration certificate.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.01
MOBILE SYSTEM FOR RESIN VACUUM INFUSION

This system has been designed for allowing resin vacuum infusion moulding and
composite fibre vacuum forming.
The system is composed of:
- A welded sheet steel autoclave featuring a perfect vacuum seal, equipped with a
3D drawings are available on vuototecnica.net

transparent methacrylate lid that can be manually removed.

- An oil-bath rotating vane pump for high vacuum.
- A reducer for adjusting the required level of vacuum.
- A vacuum gauge, for a direct reading of the level of vacuum in the autoclave.
- A three-way manual valve for pump vacuum interception and for restoring
the atmospheric pressure inside the autoclave.
- A two-way valve for vacuum interception at the application.
- Switchgear enclosed in a special casing.
- A profiled steel frame for assembling all the components mounted on wheels.
- A handle to move and place it.
Resin vacuum infusion moulding is carried out connecting the connector
controlled by the two-way manual valve to the mould.
The resin inside its container is sucked via the vacuum inside the mould, until it’s
totally full. The resin in excess is collected in the autoclave.
The same connector can be connected to the vacuum press bag for forming
composite fibres.
The installed vacuum pumps can reach a maximum level of vacuum of 99.5%
inside the autoclave. Therefore, this device can also be used as a degasifier.
The vacuum reducer allows adjusting the level of vacuum within a minimum value of
20% a maximum value of 99.5%.
Upon request they can also be supplied in different versions.

3-way vacuum interception and atmospheric Switchgear

pressure restoring valve

Vacuum gauge 09 03 10 Vacuum reducer

2-way vacuum
interception valve

100-litre
autoclave

Liquid Vacuum pump

discharge cap

Autoclave Pump Motor performance Motor power Switchgear A Weight

Item
Litres mod. Volt Kw item Kg
DR 100 M 01 100 RVP 21 3 ~ 230/400-50Hz 0.75 DR 100 90 1100 64.0
DR 100 M 02 100 RVP 40 3 ~ 230/400-50Hz 1.10 DR 100 90 1100 87.5
11
NOTE: The vacuum gauges installed can be supplied with an Accredia calibration certificate.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.02
ELECTRICAL EQUIPMENT FOR VACUUM TESTS

These devices have been created for testing the weldings and,
therefore, the sealing of cellophane or PVC wrappings for food
products.
In fact, the wrapping placed inside a bell jar tends to inflate because

3D drawings are available on vuototecnica.net

of the pressure differential created between the air at atmospheric
pressure contained inside and the vacuum created inside the bell jar.
The higher the level of vacuum reached in the bell jar and the greater
the thrust that the air contained in the wrapping will exert on the walls
and, therefore, on the weldings.
The devices for vacuum tests are composed of:
- A mobile transparent Plexiglass bell jar.
- A support surface with seal.
- A dry rotating vane vacuum pump.
- Two 2-way manual valves for vacuum interception.
- A vacuum gauge for a direct reading of the level of vacuum and the
atmospheric air in the bell jar at the end of the cycle.
- A switchgear enclosed in a special protective casing with a digital
vacuum switch to adjust the level of vacuum in the bell jar.
- A bent sheet steel frame with anti-vibration feet for assembling all
the components described above.
The level of vacuum that can be reached inside the bell jar depends on
the pump installed.
The test values are adjustable and can be automatically repeated
Available in other versions upon request.

Air inlet valve Vacuum interception valve Digital vacuum switch

item 12 40 10

Vacuum gauge item 09 05 10 Switchgear

Casing
Vacuum pump

Bell jar Pump Motor performance Motor power Switchgear A D Weight

Item
Litres mod. Volt Kw item Ø Kg
ATS 05 5.5 VTS 4M 1 ~ 230-50Hz 0.18 DO 06 95 V 300 200 21.5
ATS 20 21.5 VTS 10M 1 ~ 230-50Hz 0.37 DO 06 95 V 500 400 29.5
11
NOTE: The vacuum gauges installed can be supplied with an Accredia calibration certificate.

mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.03
EQUIPMENT FOR VACUUM TESTS

The function of these devices is to test the welding sealing in flow-pack, cellophane or food product
wrappings.
They are composed of:
- A transparent Plexiglass cylindrical container into which the water is poured and the vacuum is created.
3D drawings are available on vuototecnica.net

- A mobile transparent Plexiglass lid with, on its lower part, a perforated disc fixed via a pin which is for
keeping the flow-pack wrapping submerged in the water, in the container and on its upper part, the
instruments for managing and controlling the vacuum.
- A multiple ejector multi-stage vacuum generator.
- A check valve located on the generator suction inlet to prevent the air from returning into the container
when the generator is not in operation.
- A sleeve valve for compressed air interception.
- A supply compressed air reducer equipped with pressure gauge.
- A 2-way manual valve for restoring the atmospheric pressure inside the container.
The wrapping submerged in the water in the container tends to inflate because of the pressure differential
produced between the air at atmospheric pressure on its inside and the vacuum created in the container.
The higher the level of vacuum reached in the bell jar and the greater the thrust that the air contained in
the wrapping will exert on the walls and, therefore, on the weldings.
Any air leak from the wrapping due to a defecting welding is proved by bubbles that indicate the exact
point of the welding that’s leaking.
The level of vacuum that can be reached inside the bell jar depends on the pump installed.
The test values are adjustable and can be automatically repeated.
Available in other versions upon request.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Fluid temperature: from -5 to +50°C
Level of filtration: 60 μ
Handwheel Pressure reducer

Vacuum Pressure
gauge gauge

Plexiglass
container

Packaged
product

Water

Drain hole
Air inlet valve

Vacuum
generator

Compressed air interception

Check valve valve
For Ø8 ext. hose

Capacity A B C D E F Generator Vacuum gauge Weight

Item
L Ø Ø Ø item item Kg
ATP 02 6.0 100 220 200 100 190 --- M10 09 03 15 5.0
ATP 03 26.0 100 250 457 116 433 G1/4” M14 09 03 15 18.0
ATP 04 56.0 100 450 457 280 433 G1/4” M18 09 03 15 25.0
11
NOTE: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
The vacuum gauges installed can be supplied with an Accredia calibration certificate.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.04
SUCTION UNITS WITH SYPHON FILTER GA FS 5 and GA FS 10

These suction units with syphon filter allow sucking fluids saturated with condensation
or mixed with water and liquids. They share all the best technical features of syphon
filters and vacuum generators. In fact, they keep liquids and solid impurities, while the
vacuum generator can suck fluids saturated with vapours or liquid condensation without

3D drawings are available on vuototecnica.net

compromising its performance.
These devices are composed of:
- A standard syphon filter described in Chapter 5.
- A compressed air-fed multi-stage vacuum generator.
- A pneumatic vacuum switch for adjusting the level of vacuum
- A vacuum gauge for a direct reading of the level of vacuum in the container.
- A pneumatic valve for supplying the vacuum generator operated by the vacuum switch
- A sleeve valve for compressed air interception.
The level of vacuum, preset with the vacuum switch, is automatically maintained in the
Plexiglass container. These suction units with syphon filter are suited for vacuum cup
clamping systems for gripping glass, marble, granite, light alloys and in all those cases with
a considerable presence of refrigerating liquids.
They are also recommended for suctioning creamy or muddy substances which can be
difficult to handle with traditional pumps.
These suction assemblies are fed by compressed air at a pressure of 4-6 bar only.
Available in other versions upon request.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Fluid temperature: from -5 to +50°C
Level of filtration: 60 μ
interception valve
Compressed air

Air inlet valve

item 13 02 11

Pressure
reducer

For Ø 8 ext. hose

Vacuum switch
12 02 30
Vacuum gauge
09 03 15
generator
Vacuum
Vacuum interception valve
item 13 02 11

Filter
cartridge
Cock for liquid
discharge

A B C H L M O R Vacuum generator Capacity Weight

Item
Ø Ø item L Kg
GA FS 5 445 130 175 250 150 25 10 G3/8” M14 6.0 6.0
GA FS 10 535 130 175 340 150 25 10 G3/8” M14 8.5 6.5 11
NOTE: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.05
SUCTION UNITS WITH SYPHON FILTER GA FS 20 ES - GA FS 30 ES

These suction units with syphon filters share the same features and functions as the
previous ones; their distinctive features are their size and the type of generator installed.
Their functions are also the same.
These devices are composed of:
3D drawings are available on vuototecnica.net

- A standard syphon filter described in Chapter 5.

- A compressed air-operated multi-stage vacuum generator with a built-in energy-saving
system ES.
- A vacuum gauge for a direct reading of the level of vacuum in the container.
- A shut off valve to intercept compressed air
The level of vacuum, preset with the vacuum switch, is automatically maintained in the
Plexiglass container. Like the previous ones, these suction units with syphon filter are
also suited for vacuum cup clamping systems for gripping glass, marble, granite, light
alloys and in all those cases with a considerable presence of refrigerating liquids.
They are also recommended for suctioning creamy or muddy substances which can be
difficult to handle with traditional pumps.
These suction assemblies are fed by compressed air at a pressure of 4-6 bar only.
Available in other versions upon request.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Fluid temperature: from -5 to +50°C
Level of filtration: 60 μ

Vacuum generator with

built-in vacuum switch
Air inlet valve

Vacuum gauge
09 05 10
Vacuum interception

Filter
cartridge
valve

For Ø d
ext. hose
Magnetic level switch

Coaxial servo-piloted
ball supply valve
interception valve
Compressed air

Cock for liquid

discharge

A B C d D E G H I L M N O P R Generator Capacity Weight

Item of vacuum
Ø Ø Ø Ø item L Kg
GA FS 20 ES 800 130 175 8 200 25 100 410 290 150 25 240 10 145 G1/2” PVP 25 MDX ES 10.5 9.5
GA FS 25 ES 900 150 195 8 240 25 100 510 290 170 30 270 11 180 G3/4” PVP 50 MDX ES 19.5 12.0
11 GA FS 30 ES 1060 190 225 12 300 30 120 610 330 200 40 310 11 220 G1” PVP 75 MDX ES 38.0 22.0
NOTE: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.06
SAFETY SUCTION UNITS WITH SYPHON FILTER

These units have the same functions as the previous ones, but they differ in their automation and
composition. In fact, these devices are composed of:
- A standard syphon filter described in Chapter 5.
- Two compressed air-operated multi-stage vacuum generators with a built-in energy-saving system ES.

3D drawings are available on vuototecnica.net

- A vacuum gauge for a direct reading of the level of vacuum in the container.
- Two sleeve valves for compressed air interception.
These safety suction units normally provide for the operation of one vacuum generator with
subsequent automatic insertion of the other one for higher consumptions and when, for whatever
reason, the plant level of vacuum goes below the preset minimum value. All this also guarantees
continuous operation even in presence of a vacuum generator breakdown.
The level of vacuum, preset with the vacuum switch, is automatically maintained in the Plexiglass
container. These suction units with syphon filter are suited for vacuum cup clamping systems for
gripping glass, marble, granite, light alloys and in all those cases with a considerable presence of
refrigerating liquids and an effective need to ensure the presence of vacuum throughout the entire
production cycle.
They are also recommended for suctioning creamy or muddy substances which can be difficult to
handle with traditional pumps.
These suction assemblies are fed by compressed air at a pressure of 4-6 bar only. Available in other
versions upon request.
Technical features
Operating pressure: from 0.5 to 1000 absolute mbar
Fluid temperature: from -5 to +50°C
Level of filtration: 60 μ

Vacuum generator with

built-in vacuum switch
Vacuum
Coaxial servo-piloted ball

Air inlet valve

gauge
09 05 10
supply valves
Vacuum interception

Filter
cartridge
valve

For Ø d
Magnetic level switch
interception valve

ext. hose
Compressed air

Cock for liquid

discharge

A B C d D E G H I L M N O P R S T 2 Generators Capacity Weight

Item of vacuum
Ø Ø Ø Ø item L Kg
GAS FS 20 ES 800 130 175 8 200 25 100 410 290 150 25 175 10 145 G1/2” 188 188 PVP 25 MDX ES 10.5 11.5
GAS FS 25 ES 900 150 195 8 240 25 100 510 290 170 30 175 11 180 G3/4” 188 188 PVP 50 MDX ES 19.5 14.0
GAS FS 30 ES 1060 190 225 12 300 30 120 610 330 200 40 190 11 220 G1” 201 201 PVP 75 MDX ES 38.0 24.0 11
NOTE: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.07
LIQUID-SUCKING PUMP SETS

These pump sets are for sucking liquids and collect them inside their tanks. The
maximum level difference that can be exceeded is approximately 9 metres.
They are composed of:
- A welded sheet steel large-capacity tank
3D drawings are available on vuototecnica.net

- A compressed air-fed multi-stage vacuum generator

- A digital vacuum switch for adjusting the level of vacuum within which to operate
- A vacuum gauge for a direct reading of the level of vacuum in the tank
- A liquid level visible warning light
- Two magnetic switches for minimum and maximum liquid level
- One three-way vacuum solenoid valve for resetting the atmospheric pressure in
the tank, with consequent automatic discharge of the accumulated liquid
- Two vacuum reducers for level of vacuum adjustment at the application
- Three manual valves for vacuum interception
- A switchgear enclosed in a special protective casing for manual or automatic
operation selection
Liquid-sucking pump sets are normally used for extracting the water contained in
washing machine and dishwasher filters that cannot be automatically drained after
their commissioning.
They are also recommended for transferring dense liquids and creamy or muddy
substances.
Available in other versions upon request.
Vacuum generator

Vacuum gauge 09 05 10

Valvola principale
di esclusione vuoto
Vacuum reducer

3-way solenoid valve for restoring

Vacuum interception valve

Compressed air supply

Liquid level warning light

atmospheric pressure
solenoid valve
switch Item 12 40 10
Digital vacuum

Switchgear

Liquid discharge
valve

Flow rate A B C D E F G H R Generator Electrical Spare part Weight

Item of vacuum switchgear voltage
L Ø Ø Ø item Volt Kg
DVL 150 150 780 900 700 400 300 1600 G1” 1220 G3/8” PVP 75 MDXR DVL 150 90V 1 ~ 230-50Hz 63
DVL 300 300 880 1150 800 500 300 1890 G2” 1470 G3/8” PVP 140 MR DVL 150 90V 1 ~ 230-50Hz 75
DVL 500 500 980 1450 1000 600 400 2220 G2” 1800 G1/2” PVP 250 MR DVL 150 90V 1 ~ 230-50Hz 165
11 DVL 1000 1000 1180 1450 1200 800 400 2480 G3” 2000 G1” PVP 300 MDR DVL 150 90V 1 ~ 230-50Hz 214
NOTE: Vacuum generator supply must be carried out with non-lubricated compressed air, 5 micron filtration, in accordance with standard ISO 8573-1 class 4.
mm g Kg
Transformation ratio: N (newton) = Kg x 9.81 (force of gravity) inch = ; pounds = =
25.4 453.6 0.4536
11.08
SAMPLES AND EQUIPMENT FOR DEMONSTRATION USE

VACUUM TRAINING BOX - VTBOX01

A suitcase containing a sample of our most important products,

guaranteeing an informative overview on the vacuum technology

3D drawings are available on vuototecnica.net

intended for industrial automation.
It is an excellent educational, training and information tool.
An easily transportable trolley shaped case.

Technical features
VTBOX01 weight: 26 kg

650

310

390

VTBOX01

11.09
SAMPLES AND EQUIPMENT FOR DEMONSTRATION USE

TEST BENCH AND TESTS FOR THE SELECTION OF VACUUM CUPS- BT01

The device, equipped with 6 vacuum and 2 pneumatic sockets, lets

users carry out vacuum or Bernoulli suction cups tests on the objects
3D drawings are available on vuototecnica.net

to be gripped or moved, to aid in correctly choosing gripping cups.

This is a useful tool to have at trade show exhibitions, in a showroom
or in a test room, for gripping or handling demonstrations or for
technical personnel training dedicated to vacuum technology.
The device is already equipped with its own vacuum generator and
only needs to be connected to compressed air and to the electrical
power line. 1900
Contact our technical department for further information.

Technical features
Electrical power: Single-phase V230 ± 10% 50/60 Hz
Electric power: 1.5 kw
Compressed air consumption: 390 L/min 2bar
BT01 weight: 115 kg
Flight case 01 weight: 200 kg
Total weight: 315 kg
800
1300

1600 BT01

600
1000
11

11.10
SAMPLES AND EQUIPMENT FOR DEMONSTRATION USE

DEMONSTRATION UNIT FOR THE HANDLING OF POWDERS AND GRANULATED

PRODUCTS WITH FLOW GENERATORS CX - CONVY01
The special shape of the flow generators with which this unit

3D drawings are available on vuototecnica.net

is supplied and their straight-flow working principle allow for
the suctioning and handling of various nature products without
interference.
As previously described, this device is also specially recommended
for exhibitions at trade shows, showrooms or test rooms, for practical
demonstrations on the handling and transfer of powders, granulated
products, sawdust, grains, metal shavings, liquid or dry food products, etc.
Requires connection to compressed air and to the electrical power line.
1900

Technical features
Electrical power: Single-phase V230 ± 10% 50/60 Hz
Electric power: 0.5 kw
Compressed air consumption: 390 L/min 2bar
CONVY01 weight: 90 kg
Flight case 01 weight: 200 kg
Total weight: 290 kg

800
1300

CONVY01

1600

600

1000 11

11.11
SAMPLES AND EQUIPMENT FOR DEMONSTRATION USE

EQUIPPED ROBOT FOR GRIPPING AND HANDLING OBJECTS

WITH SPECIAL VACUUM CUPS AND GRIPPERS - VACBOT
The system we offer is composed of a robot fixed to a work surface,
3D drawings are available on vuototecnica.net

programmable by means of a special keyboard, servo-assisted by a

mini-compressor with a vacuum pump and a compressor, enclosed in
a sturdy metal cabinet on wheels.
The robot can be configured and equipped in various ways, for
gripping with vacuum cups or small Octopus surfaces, with repetitive
gripping programs to better render the idea of its multiple gripping
capabilities of different objects with different shapes.
This device is ideal for trade fairs or showrooms, since seeing it work
highlights the full potential of its use in the automation and handling 2000
sector in general, with the help of vacuums.
Only needs to be connected to the electrical power line.

Technical features
Electrical power: Single-phase V230 ± 10% 50/60 Hz
Electric power: 3.5 kw
VACBOT weight: 475 kg
Flight case 02 weight: 275 kg
Total weight: 750 kg
1600
1500

VACBOT
1800

1100
1300

11.12
INDEX OF PRODUCTS IN ORDER OF CODE
00 02 36 Vacuum cup support pg. 1.18 - 1.19
00 02 37 Vacuum cup support pg. 1.20
00 06 13 Vacuum cup support pg. 1.18 - 1.19
00 06 14 Vacuum cup support pg. 1.20

3D drawings are available on vuototecnica.net

00 06 15 Vacuum cup support pg. 1.21
00 07 03 N Electric coil V 12 DC - 18 W pg. 4.38
00 07 04 N Electric coil V 24 DC - 18 W pg. 4.38
00 07 06 N Electric coil V 110 DC - 18 W pg. 4.38
00 07 63 Standard connector for coils 13mm hole pg. 4.40
00 07 101 Connector with LED for coils 13mm hole pg. 4.40
00 07 104 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 105 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 172 Electric coil V 24 DC - 6.5 W pg. 4.37
00 07 173 Electric coil V24 AC - 8 V.A. pg. 4.37
00 07 174 Standard connector for coils 10mm hole pg. 4.39
00 07 177 Pilot membranes for solenoid valves pg. 4.41
00 07 186 Connector with LED and filter for coils 13mm hole pg. 4.40
00 07 221 Connector with red LED pg. 4.40
00 07 222 Connector with white LED pg. 4.40
00 07 223 Connector with red LED and filter pg. 4.40
00 07 229 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 230 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 231 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 232 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 256 N Electric coil V 24 AC - 20 V.A. pg. 4.38
00 07 258 N Electric coil V110 AC - 20 V.A. pg. 4.38
00 07 259 N Electric coil V230 AC - 20 V.A. pg. 4.38
00 07 260 Connector with LED for coils 10mm hole pg. 4.39
00 07 267 Valve sealing kit pg. 4.41
00 07 268 Valve sealing kit pg. 4.41
00 07 269 Valve sealing kit pg. 4.41
00 07 270 Valve sealing kit pg. 4.41
00 07 271 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 272 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 273 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 274 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 275 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 276 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 277 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 278 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 279 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 280 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 281 Solenoid valve sealing kit pg. 4.41
00 07 287 Valve sealing kit pg. 4.41
00 07 288 Valve sealing kit pg. 4.41
00 07 289 Valve sealing kit pg. 4.41
00 07 290 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 291 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 292 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 293 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 294 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 295 Solenoid valve sealing kit pg. 4.41 - 4.62
00 07 296 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 297 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 298 Pilot membranes for solenoid valves pg. 4.41 - 4.62
00 07 301 Low absorption solenoid pilot valve V 12 AC pg. 4.60
00 07 302 Low absorption solenoid pilot valve V 24 AC pg. 4.60
00 07 303 Low absorption solenoid pilot valve V 12 DC pg. 4.60
00 07 304 Low absorption solenoid pilot valve V 24 DC pg. 4.60 - 8.47-1
00 07 305 Low absorption solenoid pilot valve V 12 AC pg. 4.60
00 07 306 Low absorption solenoid pilot valve V 24 AC pg. 4.60
00 07 307 Low absorption solenoid pilot valve V 12 DC pg. 4.60
00 07 308 Low absorption solenoid pilot valve V 24 DC pg. 4.60
00 07 309 Low abs. solenoid pilot valve V 12 DC, bistable pg. 4.60
00 07 310 Low abs. solenoid pilot valve V 24 DC, bistable pg. 4.60
3D drawings are available on vuototecnica.net

00 07 311 Low abs. solenoid pilot valve V 12 DC, bistable pg. 4.60
00 07 366 Low abs. solenoid pilot valve V 24 DC, bistable pg. 4.60
00 07 372 Solenoid valve sealing kit 07 08 11 pg. 4.41
00 07 379 Solenoid valve sealing kit 07 08 13 pg. 4.62
00 07 380 Valve sealing kit 07 08 31 pg. 4.41
00 07 381 Solenoid valve sealing kit 07 08 51 pg. 4.41
00 07 382 Solenoid valve sealing kit 07 09 11 pg. 4.41
00 07 383 Solenoid valve sealing kit 07 09 13 pg. 4.62
00 07 384 Valve sealing kit 07 09 31 pg. 4.41
00 07 385 Solenoid valve sealing kit 07 09 51 pg. 4.41
00 07 411 NC solenoid pilot valve with interface valve pg. 4.61
00 07 412 NC solenoid pilot valve with interface valve pg. 4.61
00 08 01 Vacuum cup support pg. 1.01 - 1.106
00 08 02 Vacuum cup support pg. 1.01 - 1.106
00 08 03 Vacuum cup support pg. 1.02 - 1.68 - 1.69 - 1.71 - 1.75
1.79 - 1.87 - 1.89 - 1.106
00 08 04 Vacuum cup support pg. 1.03 - 1.68 - 1.70 - 1.76
1.79 - 1.87 - 1.90 - 1.106
00 08 05 Vacuum cup support pg. 1.02 - 1.70 - 1.102 - 1.103
1.107
00 08 06 Vacuum cup support pg. 1.71 - 1.86 - 1.87 - 1.89
1.107
00 08 07 Vacuum cup support pg. 1.94 - 1.95 - 1.107
00 08 08 Vacuum cup support pg. 1.04 - 1.95 - 1.107
00 08 09 Vacuum cup support pg. 1.72 - 1.83 - 1.105 - 1.107
00 08 10 Vacuum cup support pg. 1.76 - 1.77 - 1.108
00 08 14 Vacuum cup support pg. 1.03 - 1.102 - 1.103 - 1.108
00 08 15 Vacuum cup support pg. 1.80 - 1.97 - 1.108
00 08 18 Vacuum cup support pg. 1.52 - 1.71 - 1.97 - 1.98
1.99 - 1.101 - 1.108
00 08 19 Vacuum cup support pg. 1.81 - 1.109
00 08 20 Vacuum cup support pg. 1.02 - 1.109
00 08 21 Vacuum cup support pg. 1.03 - 1.109
00 08 22 Vacuum cup support pg. 1.05 - 1.109
00 08 24 Vacuum cup support pg. 1.84 - 1.85 - 1.110
00 08 26 Vacuum cup support pg. 1.104 - 1.110
00 08 28 Vacuum cup support pg. 1.06 - 1.110
00 08 29 Vacuum cup support pg. 1.07 - 1.110
00 08 31 Vacuum cup support pg. 1.35 - 1.111
00 08 32 Vacuum cup support pg. 1.18 - 1.19 - 1.24 - 1.111
00 08 33 Vacuum cup support pg. 1.20 - 1.24 - 1.111
00 08 34 Vacuum cup support pg. 1.35 - 1.39 - 1.112
00 08 35 Vacuum cup support pg. 1.21 - 1.112
00 08 37 Vacuum cup support pg. 1.22 - 1.26
00 08 44 Vacuum cup support pg. 1.05 - 1.112
00 08 46 Vacuum cup support pg. 1.07 - 1.113
00 08 50 Vacuum cup support pg. 1.98 - 1.99 - 1.100 - 1.101
1.113
00 08 54 FF adapter for joint couplings pg. 1.131
00 08 58 Vacuum cup support pg. 1.25 - 1.113
00 08 59 Vacuum cup support pg. 1.35 - 1.39 - 1.113
00 08 60 Vacuum cup support pg. 1.04 - 1.73 - 1.77 - 1.79
1.95 - 1.114
00 08 61 Vacuum cup support pg. 1.94 - 1.96 - 1.114
00 08 62 Vacuum cup support pg. 1.94 - 1.96 - 1.114
00 08 64 Vacuum cup support pg. 1.69 - 1.72 - 1.88 - 1.90
1.92 - 1.93 - 1.114
00 08 65 Vacuum cup support pg. 1.88 - 1.91 - 1.92 - 1.93
1.114
00 08 66 Vacuum cup support pg. 1.89 - 1.91 - 1.92 - 1.94
1.115

3D drawings are available on vuototecnica.net

00 08 67 Vacuum cup support pg. 1.69 - 1.72 - 1.88 - 1.90
1.91 - 1.93 - 1.115
00 08 68 Vacuum cup support pg. 1.34 - 1.115
00 08 70 Vacuum cup support pg. 1.42 - 1.115
00 08 71 Vacuum cup support pg. 1.43 - 1.116
00 08 72 Vacuum cup support pg. 1.34 - 1.115
00 08 73 Vacuum cup support pg. 1.34 - 1.115
00 08 75 Vacuum cup support pg. 1.43 - 1.116
00 08 76 Vacuum cup support pg. 1.43 - 1.116
00 08 81 Vacuum cup support pg. 1.82 - 1.84 - 1.116
00 08 82 Vacuum cup support pg. 1.78 - 1.101 - 1.116
00 08 83 Vacuum cup support pg. 1.16 - 1.116
00 08 91 Vacuum cup support pg. 1.06 - 1.116
00 08 92 Vacuum cup support pg. 1.05 - 1.116
00 08 97 Fixing plate pg. 1.42 - 1.115
00 08 98 Fixing plate pg. 1.41 - 1.116
00 08 99 Fixing plate pg. 1.41 - 1.116
00 08 100 Fixing plate pg. 1.41 - 1.116
00 08 101 Vacuum cup support pg. 1.78 - 1.117
00 08 102 TSP M3x5 screw pg. 1.41 - 1.116
00 08 103 Perforated TSP M3x5 screw pg. 1.42 - 1.115
00 08 107 Vacuum cup support pg. 1.21 - 1.25 - 1.117
00 08 108 Vacuum cup support pg. 1.15 - 1.117
00 08 109 Ring nut pg. 1.117
00 08 110 Vacuum cup support pg. 1.15 - 1.117
00 08 111 Ring nut pg. 1.117
00 08 112 Vacuum cup support pg. 1.15 - 1.117
00 08 113 Ring nut pg. 1.117
00 08 115 Vacuum cup support pg. 1.23 - 1.118
00 08 116 Vacuum cup support pg. 1.36 - 1.40 - 1.118
00 08 117 Vacuum cup support pg. 1.36 - 1.40 - 1.118
00 08 118 Vacuum cup support pg. 1.24 - 1.119
00 08 119 Vacuum cup support pg. 1.21 - 1.119
00 08 120 Threaded grub screw with calibrated hole pg. 1.131
00 08 121 Threaded grub screw with calibrated hole pg. 1.131
00 08 122 Threaded grub screw with calibrated hole pg. 1.131
00 08 123 Vacuum cup support pg. 1.20 - 1.24 - 1.119
00 08 126 Vacuum cup support pg. 1.17 - 1.57 - 1.119
00 08 127 Vacuum cup support pg. 1.52 - 1.83 - 1.84 - 1.105
1.120
00 08 129 MM adapter pg. 1.131
00 08 130 MF adapter pg. 1.08 - 1.131
00 08 131 MF adapter pg. 1.08 - 1.131
00 08 132 Vacuum cup support pg. 1.54 - 1.56 - 1.120
00 08 133 Vacuum cup support pg. 1.53 - 1.55 - 1.120
00 08 134 Vacuum cup support pg. 1.54 - 1.56 - 1.120
00 08 135 Vacuum cup support pg. 1.53 - 1.55 - 1.121
00 08 136 Vacuum cup support pg. 1.06 - 1.121
00 08 141 Vacuum cup support pg. 1.54 - 1.56 - 1.121
00 08 142 Vacuum cup support pg. 1.53 - 1.55 - 1.121
00 08 143 Vacuum cup support pg. 1.17 - 1.57 - 1.119
00 08 144 Vacuum cup support pg. 1.35 - 1.39 - 1.122
00 08 145 Vacuum cup support pg. 1.21 - 1.122
00 08 146 Vacuum cup support pg. 1.74 - 1.75 - 1.122
00 08 147 Vacuum cup support pg. 1.24 - 1.123
00 08 148 Vacuum cup support pg. 1.104 - 1.123
00 08 152 Punch for vacuum gauge 09 05 16 pg. 3.05
00 08 155 Vacuum cup support pg. 1.74 - 1.75 - 1.123
00 08 157 Vacuum cup support with calibrated hole pg. 9.34
00 08 158 Vacuum cup support with calibrated hole pg. 9.34
00 08 162 Vacuum cup support pg. 1.58 - 1.123
3D drawings are available on vuototecnica.net

00 08 163 Vacuum cup support pg. 1.58 - 1.124

00 08 164 Threaded grub screw with calibrated hole pg. 1.09 - 1.131
00 08 165 Threaded grub screw with calibrated hole pg. 1.09 - 1.131
00 08 170 Vacuum cup support with calibrated hole pg. 9.34
00 08 172 Vacuum cup support pg. 1.124
00 08 173 Vacuum cup support pg. 1.124
00 08 176 Threaded grub screw with calibrated hole pg. 1.131
00 08 178 Vacuum cup support with calibrated hole pg. 9.34
00 08 184 Vacuum cup support pg. 1.37 - 1.124
00 08 193 Vacuum cup support pg. 1.17 - 1.57 - 1.119
00 08 207 MF adapter for VRP-VRS-VEP-VES vacuum cups pg. 1.14
00 08 208 MF adapter for VRP-VRS-VEP-VES vacuum cups pg. 1.14
00 08 215 MF adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 216 MF adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 217 MM Adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 218 MM Adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 219 MM Adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 220 MM Adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 221 MM Adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 222 MM Adapter for VRP vacuum cups pg. 1.13 - 1.132
00 08 223 MM Adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 224 MM Adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 225 MM Adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 226 MM Adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 227 MM Adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 228 MM Adapter for VRS-VEP-VES vacuum cups pg. 1.13 - 1.132
00 08 230 MF adapter pg. 1.131
00 08 231 Vacuum cup support pg. 1.33 - 1.124
00 08 232 Vacuum cup support pg. 1.32 - 1.125
00 08 233 Vacuum cup support pg. 1.19 - 1.125
00 08 234 Vacuum cup support pg. 1.19 - 1.125
00 08 236 Vacuum cup support pg. 1.67 - 1.125
00 08 237 Vacuum cup support pg. 1.67 - 1.125
00 08 238 Vacuum cup support pg. 1.67 - 1.125
00 08 239 Vacuum cup support pg. 1.68 - 1.125
00 08 240 Vacuum cup support pg. 1.68 - 1.125
00 08 241 Vacuum cup support pg. 1.70 - 1.126
00 08 242 Vacuum cup support pg. 1.73 - 1.126
00 08 243 Vacuum cup support pg. 1.73 - 1.126
00 08 244 Vacuum cup support pg. 1.82 - 1.126
00 08 245 Vacuum cup support pg. 1.73 - 1.126
00 08 246 Vacuum cup support pg. 1.76 - 1.126
00 08 247 Vacuum cup support pg. 1.82 - 1.126
00 08 248 Vacuum cup support pg. 1.85 - 1.127
00 08 249 Vacuum cup support pg. 1.80 - 1.127
00 08 250 Vacuum cup support pg. 1.81 - 1.127
00 08 251 FF adapter for joint couplings pg. 1.131
00 08 252 FF adapter for joint couplings pg. 1.131
00 08 254 MF adapter pg. 1.131
00 08 255 MF adapter pg. 1.131
00 08 256 Vacuum cup support pg. 1.38 - 1.127
00 08 257 Vacuum cup support pg. 1.38 - 1.127
00 08 258 MF adapter pg. 1.131
00 08 259 FM gas/npt adapter pg. 1.130
00 08 260 FM gas/npt adapter pg. 1.130
00 08 261 FM gas/npt adapter pg. 1.130
00 08 262 FM gas/npt adapter pg. 1.130
00 08 263 FM gas/npt adapter pg. 1.130
00 08 264 FM gas/npt adapter pg. 1.130
00 08 265 FM gas/npt adapter pg. 1.130
00 08 266 FM gas/npt adapter pg. 1.130

3D drawings are available on vuototecnica.net

00 08 267 FM gas/npt adapter pg. 1.130
00 08 268 MF gas/npt adapter pg. 1.130
00 08 269 MF gas/npt adapter pg. 1.130
00 08 270 MF gas/npt adapter pg. 1.130
00 08 271 MF gas/npt adapter pg. 1.130
00 08 272 MF gas/npt adapter pg. 1.130
00 08 273 MF gas/npt adapter pg. 1.130
00 08 274 MF gas/npt adapter pg. 1.130
00 08 275 MF gas/npt adapter pg. 1.130
00 08 276 MF gas/npt adapter pg. 1.130
00 08 279 Stainless steel disc filter pg. 1.53 - 1.54
00 08 280 Vacuum cup support pg. 1.59 - 1.128
00 08 281 Vacuum cup support pg. 1.59 - 1.128
00 08 286 Vacuum cup support pg. 1.59 - 1.128
00 08 287 Vacuum cup support pg. 1.59 - 1.128
00 08 293 Stainless steel disc filter pg. 1.53 - 1.54
00 08 295 Stainless steel disc filter pg. 1.53 - 1.54
00 08 296 MF adapter pg. 1.131
00 08 297 MF adapter pg. 1.131
00 08 328 MF adapter for VRP-VRS-VEP-VES vacuum cups pg. 1.14
00 08 329 MF adapter for VRP-VRS-VEP-VES vacuum cups pg. 1.14
00 08 313 Vacuum cup support pg. 1.05
00 08 314 Vacuum cup support pg. 1.05
00 08 334 Threaded grub screw with calibrated hole pg. 1.09 - 1.131
00 08 343 Female support for vacuum cups pg. 1.45 - 1.47 - 1.128
00 08 344 Male support for vacuum cups pg. 1.44 - 1.46 - 1.128
00 08 345 Female support for vacuum cups pg. 1.45 - 1.47 - 1.128
00 08 346 Male support for vacuum cups pg. 1.44 - 1.46 - 1.128
00 08 347 Screw for support 00 08 402-403 pg. 1.44 - 1.45 - 1.46 - 1.47
00 08 348 Screw for support 00 08 404-405 pg. 1.44 - 1.45
00 08 364 Male support for vacuum cups pg. 1.60 - 1.129
00 08 366 Male support for vacuum cups pg. 1.60 - 1.129
00 08 372 Male support for vacuum cups pg. 1.62 - 1.129
00 08 373 Male support for vacuum cups pg. 1.62 - 1.129
00 08 374 Female support for vacuum cups pg. 1.63 - 1.129
00 08 375 Male support for vacuum cups pg. 1.62 - 1.129
00 08 376 Male support for vacuum cups pg. 1.62 - 1.129
00 08 377 Female support for vacuum cups pg. 1.63 - 1.129
00 08 392 Female support for vacuum cups pg. 1.61 - 1.129
00 08 393 Female support for vacuum cups pg. 1.61 - 1.129
00 08 394 Male support for vacuum cups pg. 1.60- 1.129
00 08 395 Male support for vacuum cups pg. 1.60 - 1.129
00 08 396 Female support for vacuum cups pg. 1.61 - 1.129
00 08 397 Female support for vacuum cups pg. 1.61 - 1.129
00 08 402 Male support for vacuum cups pg. 1.44 - 1.46 - 1.128
00 08 403 Female support for vacuum cups pg. 1.45 - 1.47 - 1.128
00 08 404 Male support for vacuum cups pg. 1.44 - 1.128
00 08 405 Female support for vacuum cups pg. 1.45 - 1.128
00 08 424 Vacuum cup support pg. 1.18 - 1.19 - 1.24 - 1.111
00 08 425 Vacuum cup support with calibrated hole pg. 9.34
00 08 465 Vacuum cup support pg. 1.17 - 1.57 - 1.119
00 08 466 Vacuum cup support pg. 1.104-1
00 11 06 Cap with 1/4” O-ring pg. 6.03
00 11 44 Cap with 1/8” O-ring pg. 6.03
00 11 113 Sealing kit for 11 01 10 pg. 3.28
00 11 114 Sealing kit for 11 02 10 pg. 3.28
00 11 115 Sealing kit for 11 03 10 pg. 3.28
00 11 116 Sealing kit for 11 04 10 pg. 3.28
00 11 117 Sealing kit for 11 05 10 pg. 3.28
00 11 118 Sealing kit for 11 06 10 pg. 3.28
00 11 119 Sealing kit for 11 03 50 pg. 3.28
3D drawings are available on vuototecnica.net

00 11 120 Sealing kit for 11 04 50 pg. 3.28

00 11 121 Sealing kit for 11 05 50 pg. 3.28
00 11 122 Sealing kit for 11 01 30 pg. 3.28
00 11 123 Sealing kit for 11 02 30 pg. 3.28
00 11 124 Sealing kit for 11 03 30 pg. 3.28
00 11 125 Sealing kit for 11 04 30 pg. 3.28
00 11 126 Sealing kit for 11 05 30 pg. 3.28
00 11 127 Sealing kit for 11 06 30 pg. 3.28
00 11 128 Sealing kit for 11 03 80 pg. 3.28
00 11 129 Sealing kit for 11 05 80 pg. 3.28
00 11 130 Sealing kit for 11 06 80 pg. 3.28
00 12 20 Cable with axial connector pg. 3.22 - 8.46-1 - 8.67 - 8.80
9.32
00 12 21 Cable with radial connector pg. 3.22 - 8.46-1 - 8.67 - 8.80
9.32
00 12 22 Wall-fixing kit for vacuum switches pg. 3.22
00 12 30 Wall-fixing kit for digital vacuum switches pg. 3.20
00 12 31 Table-fixing kit for vacuum switches pg. 3.20
00 12 32 Panel-fixing kit for vacuum switches pg. 3.20
00 12 40 Wall-fixing kit for vacuum switches pg. 3.21
00 12 41 Table-fixing kit for vacuum switches pg. 3.21
00 12 42 Panel-fixing kit for vacuum switches pg. 3.21
00 12 43 Panel-fix. kit with protect. for vacuum switches pg. 3.21
00 15 110 Sound absorbing material on the exhaust pg. 10.22
00 15 111 Sound absorbing material on ejectors pg. 10.22
00 15 157 Micro connector with LED pg. 4.61 - 8.46-1 - 8.50 - 8.67
8.80
00 15 171 Plexiglass manifold for GVMM-MI 3/7 pg. 8.81
00 15 174 Aluminium manifold for GVMM - MI 3/7 pg. 8.81
00 15 175 NC supply and blowing micro solenoid valve pg. 8.50 - 8.81
00 15 176 NO micro supply solenoid valve pg. 8.81
00 15 178 Eject. solenoid valve replacement plate pg. 8.68
00 15 187 Aluminium manifold for GVMM - MI 10/14 pg. 8.81
00 15 188 Plexiglass manifold for GVMM - MI 10/14 pg. 8.81
00 15 202 Cable set with built-in energy saving device pg. 8.66 - 8.79
00 15 203 Cable set with built-in energy saving device pg. 8.46-1 - 8.67 - 8.80
00 15 273 Cap with 1/2” O-ring pg. 6.03
00 15 291 Cap with M5 O-ring pg. 6.03
00 15 297 Low abs. solenoid pilot valve V 24 DC, bistable pg. 8.50
00 15 306 Fixing support for GVMM generators pg. 8.81
00 15 308 Flexible hose kit with fittings pg. 8.100
00 15 341 Safety protection for exhaust silencer SSX ¼” pg. 8.118
00 15 397 Threaded adapter for PVR 25 MS pg. 8.118
00 15 436 NO solenoid pilot valve with interface valve pg. 8.68
00 15 437 NC solenoid pilot valve with interface valve pg. 4.61 - 8.68
00 15 447 NC supply and blowing micro solenoid valve pg. 8.47-1
00 15 496 Flexible tube for connection to vacuum pg. 8.94 - 8.110
00 18 33 Cap with 3/8” O-ring pg. 6.03
00 BO 06 Locking plate for Octopus bars pg. 9.30
00 BO 07 Lock. plate with distrib. for Octopus bars pg. 9.30
00 DSO 07 Support for switchgear pg. 7.85
00 DSO 08 Support for switchgear pg. 7.85
00 DSV 08 Support for switchgear pg. 7.85
00 DSV 16 Supp. frame for 2 pumps and switchgear pg. 7.83
00 DSV 18 Support frame for 2 pumps pg. 7.83
00 DSV 20 Supp. frame for 3 pumps and switchgear pg. 7.84
00 DSV 33 Support for switchgear pg. 7.85
00 DSV 22 Support frame for 3 pumps pg. 7.84
00 DV 16 Support for switchgear pg. 7.85
00 FB 03 Stainless steel filtering cartridge for FB filters pg. 5.11
00 FB 13 Stainless steel filtering cartridge for FB filters pg. 5.11

3D drawings are available on vuototecnica.net

00 FB 22 Stainless steel filtering cartridge for FB filters pg. 5.11
00 FB 34 Stainless steel filtering cartridge for FB filters pg. 5.11
00 FB 45 Stainless steel filtering cartridge for FB filters pg. 5.11
00 FB 52 Stainless steel filtering cartridge for FB filters pg. 5.11
00 FC 04 Paper filtering cartridge for FC filters pg. 5.16
00 FC 08 Paper filtering cartridge for FC filters pg. 5.16
00 FC 15 Paper filtering cartridge for FC filters pg. 5.16
00 FC 22 Paper filtering cartridge for FC filters pg. 5.16
00 FC 24 Paper filtering cartridge for FC filters pg. 5.16
00 FC 29 Paper filtering cartridge for FC filters pg. 5.17
00 FC 33 Paper filtering cartridge for FC filters pg. 5.16
00 FC 34 Paper filtering cartridge for FC filters pg. 5.17
00 FCL 03 Filtering cartridge for FCL filters pg. 5.02
00 FCH 10 Vacuum cup holder fixing support pg. 2.168
00 FCH 11 Vacuum cup holder fixing support pg. 2.168
00 FCH 12 Fix.support for vacuum generators M3/M18 pg. 8.60
00 FCH 13 Fix.support for vacuum generators M3/M18 pg. 8.60
00 FCH 20 Vacuum cup holder fixing support pg. 2.168
00 FCH 21 Vacuum cup holder fixing support pg. 2.168
00 FCH 22 Fix.support for vacuum generators M3/M18 pg. 8.60
00 FCH 23 Fix. supp. for vacuum generators M3/M18 pg. 8.60
00 FO 04 Filtering cartridge for FO filters pg. 5.19
00 FO 09 Filtering cartridge for FO filters pg. 5.19
00 FO 14 Filtering cartridge for FO filters pg. 5.19
00 FO 19 Filtering cartridge for FO filters pg. 5.19
00 KIT GVMM 01 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 02 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 03 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 04 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 05 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 06 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 07 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 08 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 09 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 11 Screw kit for modular vacuum systems pg. 8.82
00 KIT GVMM 12 Screw kit for modular vacuum systems pg. 8.82
00 KIT M 3 Sealing kit for pneum. pumps pg. 10.22
00 KIT M 7 Sealing kit for pneum. pumps pg. 10.22
00 KIT M 10 Sealing kit for pneum. pumps pg. 10.22
00 KIT M 14 Sealing kit for pneum. pumps pg. 10.22
00 KIT M 18 Sealing kit for pneum. pumps pg. 10.22
00 KIT PVP 25 MX Sealing kit for PVP 25 MX pg. 9.33
00 KIT PVP 40 M Sealing kit for pneum. pumps pg. 10.22
00 KIT PVP 70 M Sealing kit for pneum. pumps pg. 10.22
00 KIT PVP 100 M Sealing kit for PVP 100 M pg. 9.33 - 10.22
00 KIT PVP 140 M Sealing kit for PVP 140 M pg. 9.33 - 10.22
00 KIT PVP 150 MD Sealing kit for PVP 150 MD pg. 9.33
00 KIT PVP 170 M Sealing kit for PVP 170 M pg. 9.33 - 10.22
00 KIT PVP 200 M Sealing kit for PVP 200 M pg. 9.33 - 10.22
00 KIT PVP 250 M Sealing kit for pneum. pumps pg. 10.22
00 KIT PVP 300 M Sealing kit for pneum. pumps pg. 10.22
00 KIT PVP 300 MD Sealing kit for PVP 300 MD pg. 9.33
00 KIT PVP 450 MD Sealing kit for PVP 450 MD pg. 9.33
00 KIT TRASM-MR Reed valve kit for check on generators PVP 40-300 M/MLP pg. 8.94
00 KIT TRASMD-MDR Reed valve kit for check on vacuum generators PVP 150-750 MD/MDLP pg. 8.110
00 KIT VTL 02 Sealing kit for pump VTL 2 pg. 7.45
00 KIT VTL 04 Sealing kit for pump VTL 4 pg. 7.45
00 KIT VTL 05 Sealing kit for pump VTL 5 pg. 7.45
00 KIT VTL 10 Sealing kit for pump VTL 10 pg. 7.45
00 KIT VTL 10F Sealing kit for pump VTL 10/F pg. 7.45
00 KIT VTL 15F Sealing kit for pump VTL 15/F pg. 7.45
3D drawings are available on vuototecnica.net

00 KIT VTL 20F Sealing kit for pump VTL 20/F pg. 7.45
00 KIT VTL 25FG Sealing kit for pump VTL 25/FG pg. 7.45
00 KIT VTL 30FG Sealing kit for pump VTL 30/FG pg. 7.45
00 KIT VTL 35FG Sealing kit for pump VTL 35/FG pg. 7.45
00 KIT VTL 40G1 Sealing kit for pump VTL 40/G1 pg. 7.45
00 KIT VTL 50G1 Sealing kit for pump VTL 50/G1 pg. 7.45
00 KIT VTL 65G1 Sealing kit for pump VTL 65/G1 pg. 7.45
00 KIT VTL 75G1 Sealing kit for pump VTL 75/G1 pg. 7.45
00 KIT VTL 90G1 Sealing kit for pump VTL 90/G1 pg. 7.45
00 KIT VTL 105G1 Sealing kit for pump VTL 105/G1 pg. 7.45
00 KIT VTS 02 Sealing kit for pump VTS 2 pg. 7.61
00 KIT VTS 04 Sealing kit for pump VTS 4 pg. 7.61
00 KIT VTS 06 Sealing kit for pump VTS 6 pg. 7.61
00 KIT VTS 10 Sealing kit for pump VTS 10 pg. 7.61
00 KIT VTS 10F Sealing kit for pump VTS 10/F pg. 7.61
00 KIT VTS 10FG Sealing kit for pump VTS 10/FG pg. 7.61
00 KIT VTS 15F Sealing kit for pump VTS 15/F pg. 7.61
00 KIT VTS 15FG Sealing kit for pump VTS 15/FG pg. 7.61
00 KIT VTS 20F Sealing kit for pump VTS 20/F pg. 7.61
00 KIT VTS 20FG Sealing kit for pump VTS 20/FG pg. 7.61
00 KIT VTS 25F Sealing kit for pump VTS 25/F pg. 7.61
00 KIT VTS 25FG Sealing kit for pump VTS 25/FG pg. 7.61
00 KIT VTS 30FG Sealing kit for pump VTS 30/FG pg. 7.61
00 KIT VTS 35FG Sealing kit for pump VTS 35/FG pg. 7.61
00 LP VTL 40 Oil filter for pumps VTLP pg. 7.47
00 LP VTL 99 Oil level switch pg. 7.47
00 RVP 15 04 Fibre vane for pump RVP 15 pg. 7.44
00 RVP 15 05 Deoiling cartridge for RVP 15 pg. 7.47
00 RVP 15 06 Sealing kit for pump RVP 15 pg. 7.45
00 RVP 21 04 Fibre vane for pump RVP 21 pg. 7.44
00 RVP 21 05 Deoiling cartridge for RVP 21 pg. 7.47
00 RVP 21 06 Sealing kit for pump RVP 21 pg. 7.45
00 RVP 40 04 Fibre vane for pump RVP 40 pg. 7.44
00 RVP 40 05 Deoiling cartridge for RVP 40 pg. 7.47
00 RVP 40 06 Sealing kit for pump RVP 40 pg. 7.45
00 RVP 40 07 Oil filter for pump RVP 40 pg. 7.47
00 RVP 60 04 Fibre vane for pump RVP 60 pg. 7.44
00 RVP 60 05 Deoiling cartridge for RVP 60 pg. 7.47
00 RVP 60 06 Sealing kit for pump RVP 60 pg. 7.45
00 RVP 60 07 Oil filter for pump RVP 60 pg. 7.47
00 RVP 100 04 Fibre vane for pump RVP 100 pg. 7.44
00 RVP 100 05 Deoiling cartridge for RVP 100 pg. 7.47
00 RVP 100 06 Sealing kit for pump RVP 100 pg. 7.45
00 RVP 100 07 Oil filter for pump RVP 100 pg. 7.47
00 RVP 160 04 Fibre vane for pump RVP 160 pg. 7.44
00 RVP 160 05 Deoiling cartridge for RVP 160 pg. 7.47
00 RVP 160 06 Sealing kit for pump RVP 160 pg. 7.45
00 RVP 160 07 Oil filter for pump RVP 160 pg. 7.47
00 RVP 200 04 Fibre vane for pump RVP 200 pg. 7.44
00 RVP 200 05 Deoiling cartridge for RVP 200 pg. 7.47
00 RVP 200 06 Sealing kit for pump RVP 200 pg. 7.45
00 RVP 200 07 Oil filter for pump RVP 200 pg. 7.47
00 RVP 250 04 Fibre vane for pump RVP 250 pg. 7.44
00 RVP 250 05 Deoiling cartridge for RVP 250 pg. 7.47
00 RVP 250 06 Sealing kit for pump RVP 250 pg. 7.45
00 RVP 250 07 Oil filter for pump RVP 250 pg. 7.47
00 RVP 300 04 Fibre vane for pump RVP 300 pg. 7.44
00 RVP 300 05 Deoiling cartridge for RVP 300 pg. 7.47
00 RVP 300 06 Sealing kit for pump RVP 300 pg. 7.45
00 RVP 300 07 Oil filter for pump RVP 300 pg. 7.47
00 SO 05 Stainless steel disc filter pg. 9.34

3D drawings are available on vuototecnica.net

00 SO 10 Stainless steel disc filter pg. 9.34
00 SO 14 Stainless steel disc filter pg. 9.34
00 VTL 00 11 Adjustable drip oiler pg. 7.46
00 VTL 02 10 Fibre vane for pump VTL 2 pg. 7.44
00 VTL 04 10 Fibre vane for pump VTL 4 pg. 7.44
00 VTL 05 10 Fibre vane for pump VTL 5 pg. 7.44
00 VTL 10 10 Fibre vane for pump VTL 10 pg. 7.44
00 VTL 10F 10 Fibre vane for pump VTL 10/F pg. 7.44
00 VTL 15F 10 Fibre vane for pump VTL 15/F pg. 7.44
00 VTL 20F 10 Fibre vane for pump VTL 20/F pg. 7.44
00 VTL 25FG 10 Fibre vane for pump VTL 25/FG pg. 7.44
00 VTL 30FG 10 Fibre vane for pump VTL 30/FG pg. 7.44
00 VTL 35FG 10 Fibre vane for pump VTL 35/FG pg. 7.44
00 VTL 40G1 10 Fibre vane for pump VTL 40/G1 pg. 7.44
00 VTL 50G1 10 Fibre vane for pump VTL 50/G1 pg. 7.44
00 VTL 65G1 10 Fibre vane for pump VTL 65/G1 pg. 7.44
00 VTL 75G1 10 Fibre vane for pump VTL 75/G1 pg. 7.44
00 VTL 75G1 29 Deoiling cartridge for VTL 75/G1 pg. 7.47
00 VTL 90G1 10 Fibre vane for pump VTL 90/G1 pg. 7.44
00 VTL 90G1 29 Deoiling cartridge for VTL 90/G1 pg. 7.47
00 VTL 105G1 10 Fibre vane for pump VTL 105/G1 pg. 7.44
00 VTL 105G1 29 Deoiling cartridge for VTL 105/G1 pg. 7.47
00 VTS 02 10 Graphite vane for pump VTS 2 pg. 7.60
00 VTS 02 11 Front flange with graphite disc pg. 7.60
00 VTS 02 15 Rear flange with graphite disc pg. 7.60
00 VTS 04 10 Graphite vane for pump VTS 4 pg. 7.60
00 VTS 04 11 Front flange with graphite disc pg. 7.60
00 VTS 06 07 Front flange with graphite disc pg. 7.60
00 VTS 06 10 Graphite vane for pump VTS 6 pg. 7.60
00 VTS 06 12 Rear flange with graphite disc pg. 7.60
00 VTS 10 10 Graphite vane for pump VTS 10 pg. 7.60
00 VTS 10 11 Front flange with graphite disc pg. 7.60
00 VTS 10 20 Rear flange with graphite disc pg. 7.60
00 VTS 10F 10 Graphite vane for pump VTS 10/F pg. 7.60
00 VTS 10F 15 Front flange with graphite disc pg. 7.60
00 VTS 10F 19 Rear flange with graphite disc pg. 7.60
00 VTS 10FG 10 Graphite vane for pump VTS 10/FG pg. 7.60
00 VTS 15F 10 Graphite vane for pump VTS 15/F pg. 7.60
00 VTS 15FG 10 Graphite vane for pump VTS 15/FG pg. 7.60
00 VTS 20F 10 Graphite vane for pump VTS 20/F pg. 7.60
00 VTS 20FG 10 Graphite vane for pump VTS 20/FG pg. 7.60
00 VTS 25F 05 Rear flange with graphite disc pg. 7.60
00 VTS 25F 10 Graphite vane for pump VTS 25/F pg. 7.60
00 VTS 25FG 10 Graphite vane for pump VTS 25/FG pg. 7.60
00 VTS 30FG 10 Graphite vane for pump VTS 30/FG pg. 7.60
00 VTS 35FG 10 Graphite vane for pump VTS 35/FG pg. 7.60
01 04 10 Vacuum cup pg. 1.01
01 05 10 Vacuum cup pg. 1.01
01 06 10 Vacuum cup pg. 1.01
01 06 50 Vacuum cup pg. 1.86
01 07 07 Vacuum cup pg. 1.01
01 07 13 Vacuum cup pg. 1.67
01 08 07 Vacuum cup pg. 1.67
01 08 10 Vacuum cup pg. 1.01
01 08 50 Vacuum cup pg. 1.86
01 09 07 Vacuum cup pg. 1.01
01 10 10 Vacuum cup pg. 1.02 - 1.03
01 11 08 Vacuum cup pg. 1.67
01 11 16 Vacuum cup pg. 1.87
01 11 50 Vacuum cup pg. 1.86
01 12 10 Vacuum cup pg. 1.02 - 1.03
3D drawings are available on vuototecnica.net

01 12 20 Vacuum cup pg. 1.42

01 12 30 Vacuum cup pg. 1.43
01 12 40 Vacuum cup pg. 1.43
01 12 50 Vacuum cup pg. 1.43
01 14 09 Vacuum cup pg. 1.68
01 14 10 Vacuum cup pg. 1.68
01 14 15 Vacuum cup pg. 1.69
01 14 32 Vacuum cup pg. 1.69 - 1.70
01 15 04 Vacuum cup pg. 1.70
01 15 10 Vacuum cup pg. 1.02- 1.03
01 15 15 Vacuum cup pg. 1.70
01 15 23 Vacuum cup pg. 1.88 - 1.89
01 16 20 Vacuum cup pg. 1.89 - 1.90
01 16 26 Vacuum cup pg. 1.71
01 17 12 Vacuum cup pg. 1.71
01 17 31 N Disc cup pg. 10.24
01 18 10 Vacuum cup pg. 1.02 - 1.03
01 18 12 Vacuum cup pg. 1.72
01 18 23 Vacuum cup pg. 1.90 - 1.91
01 18 29 Vacuum cup pg. 1.91 - 1.92
01 18 35 Vacuum cup pg. 1.93 - 1.94
01 18 50 Vacuum cup pg. 1.94
01 19 17 Vacuum cup pg. 1.95
01 19 31 Vacuum cup pg. 1.72
01 20 04 Vacuum cup pg. 1.73
01 20 06 S Vacuum cup pg. 1.73
01 20 08 Vacuum cup pg. 1.73
01 20 10 Vacuum cup pg. 1.02 - 1.03
01 20 11 S Vacuum cup pg. 1.73
01 20 12 Vacuum cup pg. 1.74
01 20 14 N Vacuum cup pg. 1.74
01 20 15 Vacuum cup pg. 1.75
01 20 23 Vacuum cup pg. 1.53 - 1.54
01 20 24 Vacuum cup pg. 1.75 - 1.76
01 20 30 S Bellows vacuum cups pg. 1.52
01 20 60 Vacuum cup pg. 1.95 - 1.96
01 22 06 Vacuum cup pg. 1.76
01 22 10 Vacuum cup pg. 1.02 - 1.03
01 22 19 Vacuum cup pg. 1.55 - 1.56
01 22 24 Vacuum cup pg. 1.76
01 22 45 Vacuum cup pg. 1.77
01 22 99 Vacuum cup pg. 1.77
01 24 06 S Vacuum cup pg. 1.32
01 25 08 Vacuum cup pg. 1.77
01 25 10 Vacuum cup pg. 1.04
01 25 12 Vacuum cup pg. 1.78
01 25 14 N Vacuum cup pg. 1.78
01 25 15 Vacuum cup pg. 1.02 - 1.03
01 25 28 Vacuum cup pg. 1.79
01 25 35 Vacuum cup pg. 1.97
01 26 10 Vacuum cup pg. 1.79
01 27 24 Vacuum cup pg. 1.80
01 30 10 Vacuum cup pg. 1.04
01 30 15 Vacuum cup pg. 1.02 - 1.03
01 30 24 Vacuum cup pg. 1.80
01 30 24 L Vacuum cup pg. 1.80
01 30 32 Vacuum cup pg. 1.53 - 1.54
01 30 41 NG Disc cup pg. 10.24
01 30 45 Bellows vacuum cup pg. 1.52
01 30 50 Vacuum cup pg. 1.97 - 1.98
01 30 55 Vacuum cup pg. 1.99 - 1.100

3D drawings are available on vuototecnica.net

01 30 91 N Vacuum cup pg. 10.24
01 30 99 Vacuum cup pg. 1.98 - 1.99
01 31 06 S Vacuum cup pg. 1.33
01 31 12 S Vacuum cup pg. 1.80
01 32 30 Vacuum cup pg. 1.81
01 32 36 Vacuum cup pg. 1.81
01 33 50 Vacuum cup pg. 1.101
01 34 26 Vacuum cup pg. 1.55 - 1.56
01 35 10 Vacuum cup pg. 1.04
01 35 12 Vacuum cup pg. 1.82
01 35 15 Vacuum cup pg. 1.02 - 1.03
01 35 27 Vacuum cup pg. 1.60 - 1.61
01 40 14 Vacuum cup pg. 1.82
01 40 15 Vacuum cup pg.1.02 - 1.03
01 40 18 Vacuum cup pg. 1.82
01 40 25 Vacuum cup pg. 1.83
01 40 42 Vacuum cup pg. 1.53 - 1.54
01 40 50 Vacuum cup pg. 1.101
01 40 70 Vacuum cup pg. 1.83
01 40 75 Vacuum cup pg. 1.35 - 1.37 - 1.144 - 1.146
1.148 - 1.156
01 40 80 Vacuum cup pg. 1.102
01 42 15 Foam rubber vacuum cup pg. 1.24
01 42 90 Vacuum cup pg. 1.103
01 43 28 Vacuum cup pg. 1.55 - 1.56
01 44 30 Vacuum cup pg. 1.84
01 45 10 Vacuum cup pg. 1.05
01 45 15 Vacuum cup pg. 1.02 - 1.03
01 46 13 N Vacuum cup pg. 1.34
01 48 18 Vacuum cup pg. 1.84
01 50 20 Vacuum cup pg. 1.84
01 50 53 Vacuum cup pg. 1.53 - 1.54
01 50 60 A Vacuum cup pg. 1.104-1
01 50 70 Vacuum cups pg. 1.104
01 52 40 Vacuum cup pg. 1.60 - 1.61
01 52 50 Vacuum cup pg. 1.104
01 53 35 Vacuum cup pg. 1.55 - 1.56
01 54 18 Vacuum cup pg. 1.85
01 56 15 Vacuum cup pg. 1.16
01 56 30 Vacuum cup pg. 1.105
01 57 81 S Disc cup pg. 10.24
01 60 10 Vacuum cup pg. 1.05
01 64 15 Foam rubber vacuum cup pg. 1.24
01 65 15 Vacuum cup pg. 1.18 - 1.136 - 1.138 - 1.139
01 65 16 Vacuum cup pg. 1.18
01 65 28 Vacuum cup pg. 1.85
01 73 14 N Vacuum cup pg. 1.34
01 75 30 Vacuum cup pg. 1.105
01 75 31 Vacuum cup pg. 1.105
01 75 42 Vacuum cup pg. 1.57
01 76 24 Vacuum cup pg. 1.15
01 80 20 Vacuum cup pg. 1.17
01 80 60 A Vacuum cup pg. 1.104-1
01 85 10 Vacuum cup pg. 1.06 - 1.07
01 85 15 Vacuum cup pg. 1.19 - 1.137 - 1.140 - 1.141
1.143 - 1.145
01 85 15 M Vacuum cup pg. 1.147
01 85 16 Vacuum cup pg. 1.19
01 90 24 Vacuum cup pg. 1.15
01 92 15 Foam rubber vacuum cup pg. 1.24
01 95 14 N Vacuum cup with support pg. 1.34
3D drawings are available on vuototecnica.net

01 107 75 Foam rubber vacuum cup pg. 1.39

01 110 10 Vacuum cup pg. 1.20 - 1.137 - 1.140 - 1.141
1.143 - 1.145
01 110 10 M Vacuum cup pg. 1.147 - 1.149 - 1.155
01 110 24 Vacuum cup pg. 1.15
01 110 58 Vacuum cup pg. 1.58
01 120 90 Vacuum cup pg. 1.35 - 1.38 - 1.144 - 1.146
1.148 - 1.150 - 1.157
01 127 15 Foam rubber vacuum cup pg. 1.25
01 135 50 Foam rubber vacuum cup pg. 1.39
01 135 60 Foam rubber vacuum cup pg. 1.39
01 150 10 Vacuum cup pg. 1.21 - 1.137 - 1.143 - 1.145
01 150 10 M Vacuum cup pg. 1.147 - 1.149 - 1.155
01 150 36 Vacuum cup pg. 1.15
01 150 55 Vacuum cup pg. 1.59
01 150 65 Vacuum cup pg. 1.35
01 150 74 Vacuum cup pg. 1.58
01 150 75 Vacuum cup pg. 1.35 - 1.38 - 1.144 - 1.146
1.148 - 1.150 - 1.157
01 180 15 Foam rubber vacuum cup pg. 1.25
01 210 60 Vacuum cup pg. 1.59
01 220 10 A Vacuum cup pg. 1.22
01 220 10 NF Foam rubber vacuum cup pg. 1.26
01 220 10 OF Foam rubber vacuum cup pg. 1.26
01 220 15 Foam rubber vacuum cup pg. 1.25
01 250 20 Vacuum cup pg. 1.23 - 1.147 - 1.149
01 290 68 Foam rubber vacuum cup pg. 1.40
01 290 140 Foam rubber vacuum cup pg. 1.40
01 300 80 Vacuum cup pg. 1.36 - 1.148 - 1.150
01 300 150 Vacuum cup pg. 1.36 - 1.148 - 1.150
02 08 28 Basic vacuum cup holders with female connector pg. 2.78
02 08 28 M Basic vacuum cup holders with male connector pg. 2.78
02 08 65 Basic vacuum cup holders with female connector pg. 2.78
02 08 65 M Basic vacuum cup holders with male connector pg. 2.78
02 08 95 Basic vacuum cup holders with female connector pg. 2.78
02 08 95 M Basic vacuum cup holders with male connector pg. 2.78
02 10 28 Basic vacuum cup holders with female connector pg. 2.79
02 10 28 M Basic vacuum cup holders with male connector pg. 2.79
02 10 65 Basic vacuum cup holders with female connector pg. 2.79
02 10 65 M Basic vacuum cup holders with male connector pg. 2.79
02 10 95 Basic vacuum cup holders with female connector pg. 2.79
02 10 95 M Basic vacuum cup holders with male connector pg. 2.79
02 11 28 Basic vacuum cup holders with female connector pg. 2.80
02 11 28 M Basic vacuum cup holders with male connector pg. 2.80
02 11 65 Basic vacuum cup holders with female connector pg. 2.80
02 11 65 M Basic vacuum cup holders with male connector pg. 2.80
02 11 95 Basic vacuum cup holders with female connector pg. 2.80
02 11 95 M Basic vacuum cup holders with male connector pg. 2.80
02 12 28 Basic vacuum cup holders with female connector pg. 2.81
02 12 28 M Basic vacuum cup holders with male connector pg. 2.81
02 12 65 Basic vacuum cup holders with female connector pg. 2.81
02 12 65 M Basic vacuum cup holders with male connector pg. 2.81
02 12 95 Basic vacuum cup holders with female connector pg. 2.81
02 12 95 M Basic vacuum cup holders with male connector pg. 2.81
02 20 23 Basic vacuum cup holders pg. 2.63
02 22 19 Basic vacuum cup holders pg. 2.64
02 25 10 Basic vacuum cup holders pg. 2.46
02 25 15 Basic vacuum cup holders pg. 2.47
02 25 35 Basic vacuum cup holders pg. 2.65
02 27 24 Basic vacuum cup holders pg. 2.48
02 30 10 Basic vacuum cup holders pg. 2.46

3D drawings are available on vuototecnica.net

02 30 15 Basic vacuum cup holders pg. 2.47
02 30 24 Basic vacuum cup holders pg. 2.48
02 30 32 Basic vacuum cup holders pg. 2.66
02 30 50 Basic vacuum cup holders pg. 2.67
02 30 55 Basic vacuum cup holders pg. 2.68
02 30 99 Basic vacuum cup holders pg. 2.67
02 32 36 Basic vacuum cup holders pg. 2.49
02 34 26 Basic vacuum cup holders pg. 2.64
02 35 10 Basic vacuum cup holders pg. 2.46
02 35 15 Basic vacuum cup holders pg. 2.50
02 40 15 Basic vacuum cup holders pg. 2.50
02 40 30 Basic vacuum cup holders pg. 2.69
02 40 42 Basic vacuum cup holders pg. 2.66
02 40 50 Basic vacuum cup holders pg. 2.70
02 40 60 Basic vacuum cup holders pg. 2.71
02 43 28 Basic vacuum cup holders pg. 2.72
02 45 10 Basic vacuum cup holders pg. 2.51
02 45 15 Basic vacuum cup holders pg. 2.52
02 50 20 Basic vacuum cup holders pg. 2.53
02 50 30 Basic vacuum cup holders pg. 2.69
02 50 40 Basic vacuum cup holders pg. 2.54
02 50 50 Basic vacuum cup holders pg. 2.71
02 50 53 Basic vacuum cup holders pg. 2.73
02 52 50 Basic vacuum cup holders pg. 2.74
02 53 35 Basic vacuum cup holders pg. 2.75
02 56 15 Basic vacuum cup holders pg. 2.55
02 56 30 Basic vacuum cup holders pg. 2.76
02 60 10 Basic vacuum cup holders pg. 2.51
02 60 30 Basic vacuum cup holders pg. 2.69
02 60 50 Basic vacuum cup holders pg. 2.71
02 65 15 Basic vacuum cup holders pg. 2.56
02 65 20 Basic articulated vacuum cup holders pg. 2.98
02 65 28 Basic vacuum cup holders pg. 2.53
02 75 30 Basic vacuum cup holders pg. 2.76
02 75 40 Basic vacuum cup holders pg. 2.54
02 75 42 Basic vacuum cup holders pg. 2.77
02 76 24 Basic vacuum cup holders pg. 2.57
02 80 20 Basic vacuum cup holders pg. 2.58
02 85 10 Basic vacuum cup holders pg. 2.59
02 85 15 Basic vacuum cup holders pg. 2.60
02 85 20 Basic articulated vacuum cup holders pg. 2.99
02 85 30 Basic vacuum cup holders pg. 2.69
02 85 50 Basic vacuum cup holders pg. 2.71
02 90 24 Basic vacuum cup holders pg. 2.57
02 91 01 Basic vacuum cup holders fix pg. 2.103
02 91 05 Basic vacuum cup holders fix pg. 2.103
02 91 06 Basic vacuum cup holders fix pg. 2.103
02 95 28 Basic anti-rotation vacuum cup holders pg. 2.102
02 95 28 1/4” Basic anti-rotation vacuum cup holders pg. 2.102
02 95 65 Basic anti-rotation vacuum cup holders pg. 2.102
02 95 65 1/4” Basic anti-rotation vacuum cup holders pg. 2.102
02 95 95 Basic anti-rotation vacuum cup holders pg. 2.102
02 95 95 1/4” Basic anti-rotation vacuum cup holders pg. 2.102
02 99 28 Basic vacuum cup holders with shut-off valve pg. 2.97
02 99 65 Basic vacuum cup holders with shut-off valve pg. 2.97
02 99 95 Basic vacuum cup holders with shut-off valve pg. 2.97
02 100 40 Basic vacuum cup holders pg. 2.54
02 100 50 Basic vacuum cup holders pg. 2.54
02 110 10 Basic vacuum cup holders pg. 2.61
02 110 15 Basic vacuum cup holders pg. 2.62
02 110 20 Basic articulated vacuum cup holders pg. 2.100
3D drawings are available on vuototecnica.net

02 110 22 Basic articulated vacuum cup holders pg. 2.101

02 110 24 Basic vacuum cup holders pg. 2.57
03 45 10 Basic vacuum cup holders with plunger valve pg. 2.82
03 45 11 Basic vacuum cup holders with no springing plunger pg. 2.89
03 50 41 Basic vacuum cup holders with no springing plunger pg. 2.96
03 60 10 Basic vacuum cup holders with plunger valve pg. 2.83
03 60 11 Basic vacuum cup holders with no springing plunger pg. 2.90
03 65 15 Basic vacuum cup holders with plunger valve pg. 2.84
03 65 16 Basic vacuum cup holders with no springing plunger pg. 2.91
03 75 41 Basic vacuum cup holders with no springing plunger pg. 2.96
03 80 20 Basic vacuum cup holders with plunger valve pg. 2.85
03 80 21 Basic vacuum cup holders with no springing plunger pg. 2.92
03 85 10 Basic vacuum cup holders with plunger valve pg. 2.86
03 85 11 Basic vacuum cup holders with no springing plunger pg. 2.93
03 85 15 Basic vacuum cup holders with plunger valve pg. 2.87
03 85 16 Basic vacuum cup holders with no springing plunger pg. 2.94
03 100 41 Basic vacuum cup holders with no springing plunger pg. 2.96
03 100 51 Basic vacuum cup holders with no springing plunger pg. 2.96
03 110 10 Basic vacuum cup holders with plunger valve pg. 2.88
03 110 11 Basic vacuum cup holders with no springing plunger pg. 2.95
04 01 10 1/8” vacuum control valve pg. 3.23
04 01 10 INOX 1/8” stainless steel vacuum control valve pg. 3.23
04 02 10 1/2” vacuum control valve pg. 3.23
04 02 10 INOX 1/2” stainless steel vacuum control valve pg. 3.23
04 03 10 3/4” vacuum control valve pg. 3.23
04 03 10 INOX 3/4” stainless steel vacuum control valve pg. 3.23
04 04 10 1” vacuum control valve pg. 3.23
04 04 10 INOX 1” stainless steel vacuum control valve pg. 3.23
04 05 10 1”1/2 vacuum control valve pg. 3.23
04 05 10 INOX 1”1/2 stainless steel vacuum control valve pg. 3.23
05 01 10 Built-in vacuum cup pg. 1.135
05 02 10 Built-in vacuum cup pg. 1.135
05 03 10 Built-in vacuum cup pg. 1.135
05 04 10 Built-in vacuum cup pg. 1.135
05 65 15 Built-in vacuum cup pg. 1.136
05 65 15 M Special built-in vacuum cup pg. 1.138
05 65 65 Special built-in vacuum cup pg. 1.139
05 85 15 Built-in vacuum cup pg. 1.137
05 85 15 M Special built-in vacuum cup pg. 1.140
05 85 65 Special built-in vacuum cup pg. 1.141
05 110 10 Built-in vacuum cup pg. 1.137
05 110 10 M Special built-in vacuum cup pg. 1.140
05 110 65 Special built-in vacuum cup pg. 1.141
05 150 10 Built-in vacuum cup pg. 1.137
06 11 55 M Special vacuum cup holder with male connector pg. 2.124
06 11 110 M Special vacuum cup holder with male connector pg. 2.124
06 12 55 Special vacuum cup holder with female connector pg. 2.123
06 12 55 M Special vacuum cup holder with male connector pg. 2.123
06 12 110 Special vacuum cup holder with female connector pg. 2.123
06 12 110 M Special vacuum cup holder with male connector pg. 2.123
06 13 55 M Special vacuum cup holder with male connector pg. 2.124
06 13 110 M Special vacuum cup holder with male connector pg. 2.124
06 14 55 M Special vacuum cup holder with male connector pg. 2.124
06 14 110 M Special vacuum cup holder with male connector pg. 2.124
06 15 55 M Special vacuum cup holder with male connector pg. 2.124
06 15 110 M Special vacuum cup holder with male connector pg. 2.124
06 55 80 Special anti-rotation vacuum cup holders pg. 2.145
06 55 81 Special anti-rotation vacuum cup holders pg. 2.145
06 55 82 Special anti-rotation vacuum cup holders pg. 2.145
06 55 90 Special anti-rotation vacuum cup holders pg. 2.146
06 55 91 Special anti-rotation vacuum cup holders pg. 2.146

3D drawings are available on vuototecnica.net

06 55 92 Special anti-rotation vacuum cup holders pg. 2.146
06 55 93 Special anti-rotation vacuum cup holders pg. 2.146
06 55 94 Special anti-rotation vacuum cup holders pg. 2.146
06 55 95 Special anti-rotation vacuum cup holders pg. 2.146
06 55 96 Special anti-rotation vacuum cup holders pg. 2.146
06 55 100 Special adjustable anti-rotation vacuum cup holders pg. 2.147
06 55 101 Special adjustable anti-rotation vacuum cup holders pg. 2.147
06 55 102 Special adjustable anti-rotation vacuum cup holders pg. 2.147
06 55 110 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 55 111 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 55 112 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 55 113 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 55 114 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 55 115 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 55 116 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 75 42 Special vacuum cup holders pg. 2.118
06 85 10 Special vacuum cup holders pg. 2.104
06 85 13 Special vacuum cup holders with double springing pg. 2.149
06 85 15 Special vacuum cup holders pg. 2.105
06 85 17 Special vacuum cup holders with double springing pg. 2.150
06 85 20 Special vacuum cup holders with plunger valve pg. 2.125
06 85 22 Special vacuum cup holders with plunger valve pg. 2.126
06 90 24 Special vacuum cup holders pg. 2.106
06 99 55 Special vacuum cup holders with shut-off valve pg. 2.132
06 99 110 Special vacuum cup holders with shut-off valve pg. 2.132
06 100 40 Special vacuum cup holders pg. 2.107
06 100 50 Special vacuum cup holders pg. 2.108
06 110 10 Special vacuum cup holders pg. 2.109
06 110 12 Special articulated vacuum cup holders pg. 2.133
06 110 13 Special vacuum cup holders with double springing pg. 2.151
06 110 14 Spec. articulated vacuum cup holders with double spring. pg. 2.158
06 110 15 Special vacuum cup holders pg. 2.110
06 110 16 Special vacuum cup holders with double springing pg. 2.152
06 110 17 Special articulated vacuum cup holders pg. 2.134
06 110 18 Spec. articulated vacuum cup holders with double spring. pg. 2.159
06 110 20 Special vacuum cup holders with plunger valve pg. 2.127
06 110 22 Special vacuum cup holders with plunger valve pg. 2.128
06 110 24 Special vacuum cup holders pg. 2.111
06 110 30 Special vacuum cup holders pg. 2.119
06 110 32 Special articulated vacuum cup holders pg. 2.140
06 110 42 Special articulated vacuum cup holders pg. 2.142
06 110 58 Special vacuum cup holders pg. 2.120
06 110 80 Special anti-rotation vacuum cup holders pg. 2.145
06 110 81 Special articulated vacuum cup holders pg. 2.145
06 110 82 Special articulated vacuum cup holders pg. 2.145
06 110 90 Special anti-rotation vacuum cup holders pg. 2.146
06 110 91 Special anti-rotation vacuum cup holders pg. 2.146
06 110 92 Special anti-rotation vacuum cup holders pg. 2.146
06 110 93 Special anti-rotation vacuum cup holders pg. 2.146
06 110 94 Special anti-rotation vacuum cup holders pg. 2.146
06 110 95 Special anti-rotation vacuum cup holders pg. 2.146
06 110 96 Special anti-rotation vacuum cup holders pg. 2.146
06 110 100 Special adjustable anti-rotation vacuum cup holders pg. 2.147
06 110 101 Special adjustable anti-rotation vacuum cup holders pg. 2.147
06 110 102 Special adjustable anti-rotation vacuum cup holders pg. 2.147
06 110 110 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 110 111 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 110 112 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 110 113 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 110 114 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 110 115 Special adjustable anti-rotation vacuum cup holders pg. 2.148
3D drawings are available on vuototecnica.net

06 110 116 Special adjustable anti-rotation vacuum cup holders pg. 2.148
06 127 42 Special articulated vacuum cup holders pg. 2.143
06 150 10 Special vacuum cup holders pg. 2.112
06 150 12 Special articulated vacuum cup holders pg. 2.135
06 150 13 Special vacuum cup holders with double springing pg. 2.153
06 150 14 Spec. articulated vacuum cup holders with double spring. pg. 2.160
06 150 15 Special vacuum cup holders pg. 2.114
06 150 17 Special articulated vacuum cup holders pg. 2.136
06 150 18 Special vacuum cup holders with double springing pg. 2.154
06 150 19 Spec. articulated vacuum cup holders with double spring. pg. 2.161
06 150 20 Special vacuum cup holders with plunger valve pg. 2.129
06 150 22 Special vacuum cup holders with plunger valve pg. 2.130
06 150 30 Special vacuum cup holders pg. 2.119
06 150 32 Special articulated vacuum cup holders pg. 2.141
06 150 36 Special vacuum cup holders pg. 2.113
06 150 42 Special articulated vacuum cup holders pg. 2.144
06 150 74 Special vacuum cup holders pg. 2.121
06 180 30 Special vacuum cup holders pg. 2.119
06 200 10 Special vacuum cup holders pg. 2.114
06 200 12 Special articulated vacuum cup holders pg. 2.136
06 200 13 Special vacuum cup holders with double springing pg. 2.154
06 200 14 Spec. articulated vacuum cup holders with double spring. pg. 2.161
06 200 20 Special vacuum cup holders with plunger valve pg. 2.130
06 220 10 A Special vacuum cup holders pg. 2.116
06 220 10 NF Special vacuum cup holders pg. 2.115
06 220 10 OF Special vacuum cup holders pg. 2.115
06 220 12 A Special articulated vacuum cup holders pg. 2.138
06 220 12 NF Special articulated vacuum cup holders pg. 2.137
06 220 12 OF Special articulated vacuum cup holders pg. 2.137
06 220 13 A Special vacuum cup holders with double springing pg. 2.156
06 220 13 NF Special vacuum cup holders with double springing pg. 2.155
06 220 13 OF Special vacuum cup holders with double springing pg. 2.155
06 220 14 A Spec. articulated vacuum cup holders with double spring. pg. 2.163
06 220 14 NF Spec. articulated vacuum cup holders with double spring. pg. 2.162
06 220 14 OF Spec. articulated vacuum cup holders with double spring. pg. 2.162
06 250 10 Special vacuum cup holders pg. 2.114
06 250 12 Special articulated vacuum cup holders pg. 2.136
06 250 13 Special vacuum cup holders with double springing pg. 2.154
06 250 14 Spec. articulated vacuum cup holders with double spring. pg. 2.161
06 250 20 Special vacuum cup holders with plunger valve pg. 2.130
06 250 30 Special vacuum cup holders pg. 2.122
06 300 10 Special vacuum cup holders pg. 2.117
06 300 12 Special articulated vacuum cup holders pg. 2.139
06 300 13 Special vacuum cup holders with double springing pg. 2.157
06 300 14 Spec. articulated vacuum cup holders with double spring. pg. 2.164
06 300 20 Special vacuum cup holders with plunger valve pg. 2.131
06 350 10 Special vacuum cup holders pg. 2.117
06 350 12 Special articulated vacuum cup holders pg. 2.139
06 350 13 Special vacuum cup holders with double springing pg. 2.157
06 350 14 Spec. articulated vacuum cup holders with double spring. pg. 2.164
06 350 20 Special vacuum cup holders with plunger valve pg. 2.131
07 01 11 1/4” three-way servo-operated solenoid valve pg. 4.22
07 01 13 1/4” 3-way low-absorb. servo-operated SV pg. 4.42
07 01 16 1/4” three-way solenoid pilot valve pg. 4.17
07 01 20 1/4” two-way solenoid pilot valve pg. 4.19
07 01 31 1/4” three-way servo-operated valve pg. 4.12
07 01 51 1/4” 3-way servo-operated SV with two coils pg. 4.28
07 01 53 1/4” 3-way bistable servo-operated SV pg. 4.48
07 01 71 Coaxial shutter servo-controlled supply valve pg. 8.99
07 02 11 3/8” three-way servo-operated solenoid valve pg. 4.22
07 02 13 3/8” 3-way low-absorb. servo-operated SV pg. 4.42

3D drawings are available on vuototecnica.net

07 02 16 3/8” three-way solenoid pilot valve pg. 4.18
07 02 20 3/8” two-way solenoid pilot valve pg. 4.20
07 02 31 3/8” three-way servo-operated valve pg. 4.12
07 02 51 3/8” 3-way servo-op. SV with two coils pg. 4.28
07 02 53 3/8” 3-way bistable servo-operated SV pg. 4.48
07 02 71 Coaxial shutter servo-controlled supply valve pg. 8.99
07 02 90 Pneumatic sleeve valve pg. 8.37
07 03 11 1/2” three-way servo-operated solenoid valve pg. 4.23
07 03 13 1/2” 3-way low-absorb. servo-operated SV pg. 4.43
07 03 16 1/2” three-way solenoid pilot valve pg. 4.18
07 03 20 1/2” two-way solenoid pilot valve pg. 4.20
07 03 31 1/2” three-way servo-operated valve pg. 4.13
07 03 40 NC 1/2” three-way solenoid valve pg. 4.34
07 03 40 NO 1/2” three-way solenoid valve pg. 4.34
07 03 43 NC 1/2” 3-way low-absorb. solenoid valve pg. 4.54
07 03 43 NO 1/2” 3-way low-absorb. solenoid valve pg. 4.54
07 03 51 1/2” 3-way servo-operated SV with two coils pg. 4.29
07 03 53 1/2” 3-way bistable servo-operated SV pg. 4.49
07 03 63 NC 1/2” three-way bistable solenoid valve pg. 4.56
07 03 63 NO 1/2” three-way bistable solenoid valve pg. 4.56
07 03 71 Coaxial shutter servo-controlled supply valve with built-in pneumatic vacuum switch pg. 8.93
07 04 11 3/4” three-way servo-operated solenoid valve pg. 4.24
07 04 13 3/4” 3-way low-absorb. servo-operated SV pg. 4.44
07 04 31 3/4” three-way servo-operated valve pg. 4.13
07 04 40 NC 3/4” three-way solenoid valve pg. 4.34
07 04 40 NO 3/4” three-way solenoid valve pg. 4.34
07 04 43 NC 3/4” 3-way low-absorb. solenoid valve pg. 4.54
07 04 43 NO 3/4” 3-way low-absorb. solenoid valve pg. 4.54
07 04 51 3/4” 3-way servo-operated SV with two coils pg. 4.30
07 04 53 3/4” 3-way bistable servo-operated SV pg. 4.50
07 04 63 NC 3/4” three-way bistable solenoid valve pg. 4.56
07 04 63 NO 3/4” three-way bistable solenoid valve pg. 4.56
07 04 71 Axial shutter servo-controlled supply valve with built-in pneumatic vacuum switch pg. 8.109
07 05 11 1” three-way servo-operated solenoid valve pg. 4.24
07 05 13 1” 3-way low-absorb. servo-operated SV pg. 4.44
07 05 31 1” three-way servo-operated valve pg. 4.13
07 05 40 NC 1” three-way solenoid valve pg. 4.35
07 05 40 NO 1” three-way solenoid valve pg. 4.35
07 05 43 NC 1” 3-way low-absorb. solenoid valve pg. 4.55
07 05 43 NO 1” 3-way low-absorb. solenoid valve pg. 4.55
07 05 51 1” 3-way servo-operated SV with two coils pg. 4.30
07 05 53 1” 3-way bistable servo-operated SV pg. 4.50
07 05 63 NC 1” three-way bistable solenoid valve pg. 4.57
07 05 63 NO 1” three-way bistable solenoid valve pg. 4.57
07 06 11 1”1/2 three-way servo-operated solenoid valve pg. 4.25
07 06 13 1”1/2 3-way low-absorb. servo-operated SV pg. 4.45
07 06 31 1”1/2 three-way servo-operated valve pg. 4.14
07 06 40 NC 1”1/2 three-way solenoid valve pg. 4.36
07 06 40 NO 1”1/2 three-way solenoid valve pg. 4.36
07 06 51 1”1/2 3-way servo-operated SV with two coils pg. 4.31
07 06 53 1”1/2 3-way bistable servo-operated SV pg. 4.51
07 08 11 2” three-way servo-operated solenoid valve pg. 4.26
07 08 13 2” 3-way low-absorb. servo-operated SV pg. 4.46
07 08 31 2” three-way servo-operated valve pg. 4.15
07 08 51 2” 3-way servo-operated SV with two coils pg. 4.32
07 08 53 2” 3-way bistable servo-operated SV pg. 4.52
07 09 11 3” three-way servo-operated solenoid valve pg. 4.27
07 09 13 3” 3-way low-absorb. servo-operated SV pg. 4.47
07 09 31 3” three-way servo-operated valve pg. 4.16
07 09 51 3” 3-way servo-operated SV with two coils pg. 4.33
07 09 53 3” 3-way bistable servo-operated SV pg. 4.53
3D drawings are available on vuototecnica.net

08 04 10 Vacuum cup with support pg. 1.01

08 05 10 Vacuum cup with support pg. 1.01
08 06 10 Vacuum cup with support pg. 1.01
08 06 50 Vacuum cup with support pg. 1.86
08 07 07 Vacuum cup with support pg. 1.01
08 07 13 Vacuum cup with support pg. 1.67
08 08 07 Vacuum cup with support pg. 1.67
08 08 10 Vacuum cup with support pg. 1.01
08 08 50 Vacuum cup with support pg. 1.86
08 09 07 Vacuum cup with support pg. 1.01
08 10 10 Vacuum cup with support pg. 1.02
08 10 25 Vacuum cup with support pg. 1.03
08 11 08 Vacuum cup with support pg. 1.67
08 11 16 Vacuum cup with support pg. 1.87
08 11 17 Vacuum cup with support pg. 1.87
08 11 17 F Vacuum cup with support pg. 1.87
08 11 50 Vacuum cup with support pg. 1.86
08 12 10 Vacuum cup with support pg. 1.02
08 12 20 Vacuum cup with support pg. 1.42
08 12 30 Vacuum cup with support pg. 1.43
08 12 25 Vacuum cup with support pg. 1.03
08 12 40 Vacuum cup with support pg. 1.43
08 12 50 Vacuum cup with support pg. 1.43
08 14 09 Vacuum cup with support pg. 1.68
08 14 09 F Vacuum cup with support pg. 1.68
08 14 10 Vacuum cup with support pg. 1.68
08 14 10 F Vacuum cup with support pg. 1.68
08 14 15 Vacuum cup with support pg. 1.69
08 14 15 F Vacuum cup with support pg. 1.69
08 14 32 Vacuum cup with support pg. 1.69
08 14 32 F Vacuum cup with support pg. 1.70
08 15 04 Vacuum cup with support pg. 1.70
08 15 10 Vacuum cup with support pg. 1.02
08 15 15 Vacuum cup with support pg. 1.70
08 15 23 Vacuum cup with support pg. 1.88
08 15 23 F Vacuum cup with support pg. 1.88
08 15 24 F Vacuum cup with support pg. 1.88
08 15 25 Vacuum cup with support pg. 1.03
08 15 26 F Vacuum cup with support pg. 1.89
08 16 20 Vacuum cup with support pg. 1.89
08 16 21 Vacuum cup with support pg. 1.89
08 16 21 F Vacuum cup with support pg. 1.90
08 16 26 Vacuum cup with support pg. 1.71
08 17 12 Vacuum cup with support pg. 1.71
08 17 13 Vacuum cup with support pg. 1.71
08 18 10 Vacuum cup with support pg. 1.02
08 18 12 Vacuum cup with support pg. 1.72
08 18 12 F Vacuum cup with support pg. 1.72
08 18 23 Vacuum cup with support pg. 1.90
08 18 23 F Vacuum cup with support pg. 1.90
08 18 24 F Vacuum cup with support pg. 1.91
08 18 25 Vacuum cup with support pg. 1.03
08 18 26 F Vacuum cup with support pg. 1.91
08 18 29 Vacuum cup with support pg. 1.91
08 18 29 F Vacuum cup with support pg. 1.92
08 18 30 F Vacuum cup with support pg. 1.92
08 18 31 F Vacuum cup with support pg. 1.92
08 18 35 Vacuum cup with support pg. 1.93
08 18 35 F Vacuum cup with support pg. 1.93
08 18 36 F Vacuum cup with support pg. 1.93
08 18 37 F Vacuum cup with support pg. 1.94

3D drawings are available on vuototecnica.net

08 18 50 Vacuum cup with support pg. 1.94
08 18 51 Vacuum cup with support pg. 1.94
08 18 52 Vacuum cup with support pg. 1.94
08 19 17 Vacuum cup with support pg. 1.95
08 19 18 Vacuum cup with support pg. 1.95
08 19 31 Vacuum cup with support pg. 1.72
08 20 04 Vacuum cup with support pg. 1.73
08 20 06 Vacuum cup with support pg. 1.73
08 20 08 Vacuum cup with support pg. 1.73
08 20 10 Vacuum cup with support pg. 1.02
08 20 11 Vacuum cup with support pg. 1.73
08 20 12 Vacuum cup with support pg. 1.74
08 20 12 F Vacuum cup with support pg. 1.74
08 20 14 Vacuum cup with support pg. 1.74
08 20 14 F Vacuum cup with support pg. 1.74
08 20 15 Vacuum cup with support pg. 1.75
08 20 15 F Vacuum cup with support pg. 1.75
08 20 23 Vacuum cup with support pg. 1.53
08 20 23 F Vacuum cup with support pg. 1.54
08 20 24 Vacuum cup with support pg. 1.75
08 20 24 F Vacuum cup with support pg. 1.76
08 20 25 Vacuum cup with support pg. 1.03
08 20 30 S Vacuum cup with support pg. 1.52
08 20 60 Vacuum cup with support pg. 1.95
08 20 61 Vacuum cup with support pg. 1.96
08 20 62 Vacuum cup with support pg. 1.96
08 22 06 Vacuum cup with support pg. 1.76
08 22 10 Vacuum cup with support pg. 1.02
08 22 19 Vacuum cup with support pg. 1.55
08 22 19 F Vacuum cup with support pg. 1.56
08 22 24 Vacuum cup with support pg. 1.76
08 22 25 Vacuum cup with support pg. 1.03
08 22 45 Vacuum cup with support pg. 1.77
08 22 99 Vacuum cup with support pg. 1.77
08 24 06 S Vacuum cup with support pg. 1.32
08 25 08 Vacuum cup with support pg. 1.77
08 25 10 Vacuum cup with support pg. 1.04
08 25 11 Vacuum cup with support pg. 1.04
08 25 12 Vacuum cup with support pg. 1.78
08 25 14 Vacuum cup with support pg. 1.78
08 25 15 Vacuum cup with support pg. 1.02
08 25 22 Vacuum cup with support pg. 1.78
08 25 25 Vacuum cup with support pg. 1.03
08 25 27 Vacuum cup with support pg. 1.78
08 25 28 Vacuum cup with support pg. 1.79
08 25 28 F Vacuum cup with support pg. 1.79
08 25 35 Vacuum cup with support pg. 1.97
08 25 40 Vacuum cup with support pg. 1.97
08 26 10 Vacuum cup with support pg. 1.79
08 27 24 Vacuum cup with support pg. 1.80
08 30 10 Vacuum cup with support pg. 1.04
08 30 11 Vacuum cup with support pg. 1.04
08 30 15 Vacuum cup with support pg. 1.02
08 30 24 Vacuum cup with support pg. 1.80
08 30 24 L Vacuum cup with support pg. 1.80
08 30 25 Vacuum cup with support pg. 1.03
08 30 32 Vacuum cup with support pg. 1.53
08 30 32 F Vacuum cup with support pg. 1.54
08 30 38 B Vacuum cup with support pg. 1.08
08 30 45 S Vacuum cup with support pg. 1.52
08 30 50 Vacuum cup with support pg. 1.97
3D drawings are available on vuototecnica.net

08 30 50 F Vacuum cup with support pg. 1.98

08 30 55 Vacuum cup with support pg. 1.99
08 30 55 F Vacuum cup with support pg. 1.100
08 30 60 Vacuum cup with support pg. 1.49
08 30 99 Vacuum cup with support pg. 1.98
08 30 99 F Vacuum cup with support pg. 1.99
08 31 06 S Vacuum cup with support pg. 1.33
08 31 12 S Vacuum cup with support pg. 1.80
08 32 30 Vacuum cup with support pg. 1.81
08 32 36 Vacuum cup with support pg. 1.81
08 32 40 Vacuum cup with support pg. 1.100
08 32 52 A Vacuum cup with support pg. 1.48
08 32 99 A Vacuum cup with support pg. 1.48
08 33 50 Vacuum cup with support pg. 1.101
08 34 26 Vacuum cup with support pg. 1.55
08 34 26 F Vacuum cup with support pg. 1.56
08 35 10 Vacuum cup with support pg. 1.04
08 35 11 Vacuum cup with support pg. 1.04
08 35 12 Vacuum cup with support pg. 1.82
08 35 15 Vacuum cup with support pg. 1.02
08 35 25 Vacuum cup with support pg. 1.03
08 35 27 Vacuum cup with support pg. 1.60
08 35 27 F Vacuum cup with support pg. 1.61
08 35 27 1/8” Vacuum cup with support pg. 1.60
08 35 27 1/8”F Vacuum cup with support pg. 1.61
08 40 14 Vacuum cup with support pg. 1.82
08 40 15 Vacuum cup with support pg. 1.02
08 40 18 Vacuum cup with support pg. 1.82
08 40 24 Vacuum cup with support pg. 1.83
08 40 25 Vacuum cup with support pg. 1.03
08 40 30 Vacuum cup with support pg. 1.64
08 40 30 M Vacuum cup with support pg. 1.64
08 40 41 B Vacuum cup with support pg. 1.08
08 40 41 N Vacuum cup with support pg. 1.08
08 40 42 Vacuum cup with support pg. 1.53
08 40 42 F Vacuum cup with support pg. 1.54
08 40 50 Vacuum cup with support pg. 1.101
08 40 50 F Vacuum cup with support pg. 1.101
08 40 60 Vacuum cup with support pg. 1.65
08 40 60 M Vacuum cup with support pg. 1.65
08 40 70 Vacuum cup with support pg. 1.83
08 40 75 Vacuum cup with support pg. 1.35
08 40 75 M1 Vacuum cup with support pg. 1.37
08 40 80 Vacuum cup with support pg. 1.102
08 40 80 F Vacuum cup with support pg. 1.102
08 40 90 Vacuum cup with support pg. 1.49
08 42 15 Vacuum cup with support pg. 1.24
08 42 15 1/4” Vacuum cup with support pg. 1.24
08 42 90 Vacuum cup with support pg. 1.103
08 42 90 F Vacuum cup with support pg. 1.103
08 43 28 Vacuum cup with support pg. 1.55
08 43 28 F Vacuum cup with support pg. 1.56
08 44 30 Vacuum cup with support pg. 1.84
08 45 10 Vacuum cup with support pg. 1.05
08 45 11 Vacuum cup with support pg. 1.05
08 45 12 Vacuum cup with support pg. 1.05
08 45 13 Vacuum cup with support pg. 1.05
08 45 14 Vacuum cup with support pg. 1.05
08 45 15 Vacuum cup with support pg. 1.02
08 45 25 Vacuum cup with support pg. 1.03
08 46 13 N Vacuum cup with support pg. 1.34

3D drawings are available on vuototecnica.net

08 48 18 Vacuum cup with support pg. 1.84
08 50 20 Vacuum cup with support pg. 1.84
08 50 30 Vacuum cup with support pg. 1.64
08 50 30 M Vacuum cup with support pg. 1.64
08 50 40 Vacuum cup with support pg. 1.09 - 1.133
08 50 40 1/4”B Vacuum cup with support pg. 1.09
08 50 40 FB Vacuum cup with support pg. 1.09
08 50 40 GR B Vacuum cup with support pg. 1.09
08 50 40 M10 B Vacuum cup with support pg. 1.09
08 50 50 Vacuum cup with support pg. 1.65
08 50 50 M Vacuum cup with support pg. 1.65
08 50 53 Vacuum cup with support pg. 1.53
08 50 53 F Vacuum cup with support pg. 1.54
08 50 60 Vacuum cup with support pg. 1.104-1
08 50 70 Vacuum cup with support pg. 1.104
08 50 75 A Vacuum cup with support pg. 1.41 - 1.152
08 50 90 Vacuum cup with support pg. 1.49
08 50 99 B Vacuum cup with support pg. 1.10
08 50 99 1/4”B Vacuum cup with support pg. 1.10
08 50 99 F B Vacuum cup with support pg. 1.10
08 50 99 F S Vacuum cup with support pg. 1.10
08 52 40 Vacuum cup with support pg. 1.60
08 52 40 F Vacuum cup with support pg. 1.61
08 52 40 1/8” Vacuum cup with support pg. 1.60
08 52 40 1/8”F Vacuum cup with support pg. 1.61
08 52 50 Vacuum cup with support pg. 1.104
08 53 35 Vacuum cup with support pg. 1.55
08 53 35 F Vacuum cup with support pg. 1.56
08 54 18 Vacuum cup with support pg. 1.85
08 56 15 Vacuum cup with support pg. 1.16
08 56 30 Vacuum cup with support pg. 1.105
08 60 10 Vacuum cup with support pg. 1.05 - 1.134
08 60 11 Vacuum cup with support pg. 1.05
08 60 12 Vacuum cup with support pg. 1.05
08 60 13 Vacuum cup with support pg. 1.05
08 60 14 Vacuum cup with support pg. 1.05
08 60 30 Vacuum cup with support pg. 1.64
08 60 30 M Vacuum cup with support pg. 1.64
08 60 45 B Vacuum cup with support pg. 1.08
08 60 45 1/4”B Vacuum cup with support pg. 1.08
08 60 50 Vacuum cup with support pg. 1.65
08 60 50 M Vacuum cup with support pg. 1.65
08 60 50 M12 Vacuum cup with support pg. 1.65
08 64 15 Vacuum cup with support pg. 1.24
08 64 15 1/4” Vacuum cup with support pg. 1.24
08 65 11 A Vacuum cup with support pg. 1.29 - 1.151
08 65 15 Vacuum cup with support pg. 1.18
08 65 15 1/4” Vacuum cup with support pg. 1.18
08 65 16 Vacuum cup with support pg. 1.18
08 65 17 Vacuum cup with support pg. 1.18
08 65 28 Vacuum cup with support pg. 1.85
08 73 14 N Vacuum cup with support pg. 1.34
08 75 30 Vacuum cup with support pg. 1.105
08 75 31 Vacuum cup with support pg. 1.105
08 75 40 Vacuum cup with support pg. 1.09 - 1.133
08 75 40 1/4”B Vacuum cup with support pg. 1.09
08 75 40 F B Vacuum cup with support pg. 1.09
08 75 40 F S Vacuum cup with support pg. 1.09
08 75 40 GR B Vacuum cup with support pg. 1.09
08 75 40 GR N Vacuum cup with support pg. 1.09
08 75 40 M14 B Vacuum cup with support pg. 1.09
3D drawings are available on vuototecnica.net

08 75 42 Vacuum cup with support pg. 1.57

08 75 42 1/2” Vacuum cup with support pg. 1.57
08 75 42 1/4” Vacuum cup with support pg. 1.57
08 75 42 3/8” Vacuum cup with support pg. 1.57
08 75 43 M Vacuum cup with support pg. 1.62
08 75 43 3/8” Vacuum cup with support pg. 1.63
08 75 43 3/8”M Vacuum cup with support pg. 1.62
08 75 43 SR Vacuum cup pg. 1.62 - 1.63
08 75 99 B Vacuum cup with support pg. 1.10
08 75 99 1/4”B Vacuum cup with support pg. 1.10
08 75 99 F B Vacuum cup with support pg. 1.10
08 75 99 F S Vacuum cup with support pg. 1.10
08 76 24 1/4” Vacuum cup with support pg. 1.15
08 76 24 3/8” Vacuum cup with support pg. 1.15
08 80 20 Vacuum cup with support pg. 1.17
08 80 20 1/2” Vacuum cup with support pg. 1.17
08 80 20 1/4” Vacuum cup with support pg. 1.17
08 80 20 3/8” Vacuum cup with support pg. 1.17
08 80 50 B Vacuum cup with support pg. 1.08
08 80 60 Vacuum cup with support pg. 1.104-1
08 85 10 Vacuum cup with support pg. 1.06 - 1.134
08 85 11 A Vacuum cup with support pg. 1.29 - 1.153
08 85 12 Vacuum cup with support pg. 1.06
08 85 13 Vacuum cup with support pg. 1.06
08 85 15 Vacuum cup with support pg. 1.19
08 85 15 1/4” Vacuum cup with support pg. 1.19
08 85 15 1/2” Vacuum cup with support pg. 1.19
08 85 15 3/4” Vacuum cup with support pg. 1.19
08 85 15 1/2” S Vacuum cups for resin infusion moulds pg. 4.02
08 85 15 3/4” S Vacuum cups for resin infusion moulds pg. 4.02
08 85 16 Vacuum cup with support pg. 1.19
08 85 17 Vacuum cup with support pg. 1.19
08 85 25 Vacuum cup with support pg. 1.07
08 85 26 Vacuum cup with support pg. 1.07
08 85 30 Vacuum cup with support pg. 1.64
08 85 30 M Vacuum cup with support pg. 1.64
08 85 50 Vacuum cup with support pg. 1.65
08 85 50 M Vacuum cup with support pg. 1.65
08 85 50 M12 Vacuum cup with support pg. 1.65
08 90 24 1/4” Vacuum cup with support pg. 1.15
08 90 24 3/8” Vacuum cup with support pg. 1.15
08 92 15 Vacuum cup with support pg. 1.24
08 92 15 3/8” Vacuum cup with support pg. 1.24
08 95 14 N Vacuum cup with support pg. 1.34
08 100 40 Vacuum cup with support pg. 1.09 - 1.133
08 100 40 1/4”B Vacuum cup with support pg. 1.09
08 100 40 F B Vacuum cup with support pg. 1.09
08 100 40 F S Vacuum cup with support pg. 1.09
08 100 50 Vacuum cup with support pg. 1.09 - 1.133
08 100 50 F B Vacuum cup with support pg. 1.09
08 100 50 F S Vacuum cup with support pg. 1.09
08 100 50 M10 B Vacuum cup with support pg. 1.09
08 100 50 M14 B Vacuum cup with support pg. 1.09
08 100 99 B Vacuum cup with support pg. 1.10
08 100 99 N Vacuum cup with support pg. 1.10
08 100 99 1/4”B Vacuum cup with support pg. 1.10
08 100 99 F B Vacuum cup with support pg. 1.10
08 107 75 Vacuum cup with support pg. 1.39
08 110 10 Vacuum cup with support pg. 1.20
08 110 11 Vacuum cup with support pg. 1.20
08 110 12 Vacuum cup with support pg. 1.20

3D drawings are available on vuototecnica.net

08 110 13 Vacuum cup with support pg. 1.20
08 110 15 Vacuum cup with support pg. 1.30
08 110 15 M8 Vacuum cup with support pg. 1.30
08 110 24 1/4” Vacuum cup with support pg. 1.15
08 110 24 3/8” Vacuum cup with support pg. 1.15
08 110 30 Vacuum cup with support pg. 1.66
08 110 40 Vacuum cup with support pg. 1.30
08 110 40 M8 Vacuum cup with support pg. 1.30
08 110 58 Vacuum cup with support pg. 1.58
08 110 73 M Vacuum cup with support pg. 1.62
08 110 73 1/2” Vacuum cup with support pg. 1.63
08 110 73 1/2”M Vacuum cup with support pg. 1.62
08 110 73 SR Vacuum cup pg. 1.62 - 1.63
08 120 90 Vacuum cup with support pg. 1.35
08 120 90 M1 Vacuum cup with support pg. 1.38
08 127 15 Vacuum cup with support pg. 1.25
08 135 50 Vacuum cup with support pg. 1.39
08 135 60 Vacuum cup with support pg. 1.39
08 150 10 Vacuum cup with support pg. 1.21
08 150 11 A Vacuum cup with support pg. 1.29 - 1.154
08 150 12 Vacuum cup with support pg. 1.21
08 150 13 Vacuum cup with support pg. 1.21
08 150 14 Vacuum cup with support pg. 1.21
08 150 15 Vacuum cup with support pg. 1.30
08 150 16 Vacuum cup with support pg. 1.21
08 150 30 Vacuum cup with support pg. 1.66
08 150 36 Vacuum cup with support pg. 1.15
08 150 40 Vacuum cup with support pg. 1.30
08 150 55 Vacuum cup with support pg. 1.59
08 150 56 Vacuum cup with support pg. 1.59
08 150 65 Vacuum cup with support pg. 1.35
08 150 74 Vacuum cup with support pg. 1.58
08 150 75 Vacuum cup with support pg. 1.35
08 150 75 M1 Vacuum cup with support pg. 1.38
08 180 15 Vacuum cup with support pg. 1.25
08 180 30 Vacuum cup with support pg. 1.66
08 200 10 Vacuum cup with support pg. 1.30
08 200 40 Vacuum cup with support pg. 1.30
08 210 60 Vacuum cup with support pg. 1.59
08 210 61 Vacuum cup with support pg. 1.59
08 220 10 A Vacuum cup with support pg. 1.22
08 220 10 NF Vacuum cup with support pg. 1.26
08 220 10 OF Vacuum cup with support pg. 1.26
08 250 10 Vacuum cup with support pg. 1.30
08 250 20 Vacuum cup with support pg. 1.23
08 250 30 Vacuum cup with support pg. 1.66
08 250 40 Vacuum cup with support pg. 1.30
08 290 68 Vacuum cup with support pg. 1.40
08 290 140 Vacuum cup with support pg. 1.40
08 300 10 Vacuum cup with support pg. 1.30
08 300 40 Vacuum cup with support pg. 1.30
08 300 80 Vacuum cup with support pg. 1.36
08 300 150 Vacuum cup with support pg. 1.36
08 350 10 Vacuum cup with support pg. 1.30
08 350 40 Vacuum cup with support pg. 1.30
08 360 10 Vacuum cup with support pg. 1.31
09 01 10 Built-in vacuum gauge diam. 63 pg. 3.02
09 01 16 Built-in glycerine vacuum gauge diam. 63 pg. 3.03
09 02 10 Built-in vacuum gauge diam. 100 pg. 3.03
09 03 10 Axial vacuum gauge diam. 63 pg. 3.02
09 03 15 Axial vacuum gauge diam. 40 pg. 3.01 - 8.118 - 9.32 - 10.21
3D drawings are available on vuototecnica.net

09 03 20 Axial pressure gauge diam. 40 pg. 3.01 - 10.21

09 03 25 Axial pressure gauge diam. 40 pg. 3.01 - 9.32 - 10.21
09 05 10 Radial vacuum gauge diam. 63 pg. 3.04
09 05 16 Axial glycerine vacuum gauge diam. 63 pg. 3.04
09 05 99 Vacuum gauge diam. 63 with steel punch pg. 3.05
10 01 11 1/4” vertical check valve pg. 4.08
10 01 15 1/4” membrane check valve pg. 4.09 - 7.45 - 7.61
10 02 10 3/8” horizontal check valve pg. 4.08 - 7.45 - 7.61
10 02 11 3/8” vertical check valve pg. 4.08
10 02 15 3/8” membrane check valve pg. 4.09 - 7.45
10 03 10 1/2” horizontal check valve pg. 4.08 - 7.45 - 7.61
10 03 11 1/2” vertical check valve pg. 4.08
10 03 15 1/2” membrane check valve pg. 4.09
10 04 10 3/4” horizontal check valve pg. 4.08 - 7.45 - 7.61
10 04 11 3/4” vertical check valve pg. 4.08
10 04 15 3/4” membrane check valve pg. 4.09
10 04 20 Membrane check valve pg. 8.100
10 05 10 1” horizontal check valve pg. 4.08 - 7.45
10 05 11 1” vertical check valve pg. 4.08
10 05 15 1” membrane check valve pg. 4.09
10 05 20 Membrane check valve pg. 8.100
10 06 10 1”1/4 horizontal check valve pg. 4.08 - 7.45
10 06 11 1”1/4 vertical check valve pg. 4.08
10 07 10 1”1/2 horizontal check valve pg. 4.08 - 7.45
10 07 11 1”1/2 vertical check valve pg. 4.08
10 08 10 2” horizontal check valve pg. 4.08
10 08 11 2” vertical check valve pg. 4.08
11 01 10 1/4” vacuum reducer pg. 3.24
11 01 30 1/4” pneumatic reg. vacuum reducer pg. 3.26
11 02 10 3/8” vacuum reducer pg. 3.24
11 02 30 3/8” pneumatic reg. vacuum reducer pg. 3.26
11 03 10 1/2” vacuum reducer pg. 3.24
11 03 30 1/2” pneumatic reg. vacuum reducer pg. 3.26
11 03 50 1/2” reducer for rough vacuum pg. 3.25
11 03 80 1/2” pneumatic reg. red. for rough vacuum pg. 3.26
11 04 10 3/4” vacuum reducer pg. 3.24
11 04 30 3/4” pneumatic reg. vacuum reducer pg. 3.26
11 05 10 1/4” vacuum reducer pg. 3.24
11 05 30 1” pneumatic reg. vacuum reducer pg. 3.26
11 05 50 1” reducer for rough vacuum pg. 3.25
11 05 80 1” pneumatic reg. red. for rough vacuum pg. 3.26
11 06 10 1”1/2 vacuum reducer pg. 3.24
11 06 30 1”1/2 pneumatic reg. vacuum reducer pg. 3.26
11 06 50 1”1/2 reducer for rough vacuum pg. 3.25
11 06 80 1”1/2 pneum. reg. red. for rough vacuum pg. 3.26
12 01 30 Mini pneumatic vacuum switch NC pg. 3.06
12 01 30 X Mini pneumatic vacuum switch for generators PVP 25-75 MDX/MDXLP pg. 8.99
12 02 10 Mini electromechanical vacuum switch pg. 3.07
12 02 30 Mini pneumatic vacuum switch NO pg. 3.06
12 05 10 Digital micro vacuum switch pg. 3.08
12 05 10 N Digital micro vacuum switch pg. 3.09
12 05 10 P Digital micro vacuum switch pg. 3.09
12 05 11 Digital micro vacuum switch pg. 3.08 - 8.50
12 05 11 N Digital micro vacuum switch pg. 3.09
12 05 11 P Digital micro vacuum switch pg. 3.09 - 8.118
12 07 10 Analog vacuum switch pg. 3.11
12 10 10 Digital vacuum switch pg. 3.13 - 8.68 - 8.80 - 9.32
12 20 10 P Digital vacuum switch pg. 3.16 - 3.17
12 25 11 Digital pressure switch pg. 3.13
12 30 10 Digital vacuum switch pg. 3.14 - 3.15 - 8.47-1
12 30 10 A Digital vacuum switch with 1 analog output pg. 3.14 - 3.15

3D drawings are available on vuototecnica.net

12 35 10 P Digital pressure switch pg. 3.16 - 3.17
12 40 10 Digital vacuum switch with 2-colour display pg. 3.18 - 3.19
12 40 12 Digital vacuum switch with 2-colour display pg. 3.18 - 3.19
12 40 20 Digital vac. switch with 2-colour display pg. 3.18 - 3.19
13 01 10 1/4” two-way manual valve pg. 4.10
13 01 11 1/4” two-way miniature manual valve pg. 4.09
13 01 15 1/4” three-way manual valve pg. 4.11
13 02 10 3/8” two-way manual valve pg. 4.10
13 02 11 3/8” two-way miniature manual valve pg. 4.09
13 02 15 3/8” three-way manual valve pg. 4.11
13 03 10 1/2” two-way manual valve pg. 4.10
13 03 11 1/2” two-way miniature manual valve pg. 4.09
13 03 15 1/2” three-way manual valve pg. 4.11
13 04 10 3/4” two-way manual valve pg. 4.10
13 04 15 3/4” three-way manual valve pg. 4.11
13 05 10 1” two-way manual valve pg. 4.10
13 05 15 1” three-way manual valve pg. 4.11
13 06 10 1”1/4 two-way manual valve pg. 4.10
13 06 15 1”1/4 three-way manual valve pg. 4.11
13 07 10 1”1/2 two-way manual valve pg. 4.10
13 07 15 1”1/2 three-way manual valve pg. 4.11
13 08 10 2” two-way manual valve pg. 4.10
13 09 10 3” two-way manual valve pg. 4.10
14 01 05 Shut-off valve pg. 4.06
14 01 06 Shut-off valve for Octopus pg. 9.34
14 01 07 Shut-off valve for Octopus pg. 9.34
14 01 10 Shut-off valve pg. 4.06
14 01 11 Shut-off valve with controll. loss pg. 4.07
14 01 15 Shut-off valve pg. 4.06
14 02 10 Shut-off valve pg. 4.07
14 02 11 Shut-off valve with controll. loss pg. 4.07
14 03 10 Shut-off valve pg. 4.07
14 03 11 Shut-off valve with controll. loss pg. 4.07
14 05 10 Shut-off valve pg. 4.07
14 06 10 Shut-off valve pg. 4.07
15 01 10 Single-stage vacuum generator pg. 8.05 - 8.06
15 01 10 LP Single-stage vacuum generator pg. 8.05 - 8.06
15 01 15 LP Single-stage vacuum generator pg. 8.05 - 8.06
15 02 10 Vacuum generator with ejector pg. 8.15 - 8.16
15 02 10 LP Vacuum generator with ejector pg. 8.15 - 8.16
15 02 15 LP Vacuum generator with ejector pg. 8.15 - 8.16
15 03 10 Single-stage vacuum generator pg. 8.07 - 8.08
15 04 10 Vacuum generator with ejector pg. 8.17 - 8.18
15 05 08 SX Single-stage vacuum generator pg. 8.09 - 8.10
15 05 10 SX Single-stage vacuum generator pg. 8.09 - 8.10
15 06 08 SX Vacuum generator with ejector pg. 8.19 - 8.20
15 06 10 SX Vacuum generator with ejector pg. 8.19 - 8.20
15 07 10 SX Single-stage vacuum generator pg. 8.11 - 8.12
16 40 75 Vacuum cup with self-locking support pg. 1.144
16 85 15 Vacuum cup with self-locking support pg. 1.143
16 110 10 Vacuum cup with self-locking support pg. 1.143
16 120 90 Vacuum cup with self-locking support pg. 1.144
16 150 10 Vacuum cup with self-locking support pg. 1.143
16 150 75 Vacuum cup with self-locking support pg. 1.144
17 50 40 Self-locking vacuum cup pg. 1.133
17 60 10 Self-locking vacuum cup pg. 1.134
17 75 40 Self-locking vacuum cup pg. 1.133
17 85 10 Self-locking vacuum cup pg. 1.134
17 100 40 Self-locking vacuum cup pg. 1.133
17 100 50 Self-locking vacuum cup pg. 1.133
18 40 75 Vacuum cup with self-locking support pg. 1.146
3D drawings are available on vuototecnica.net

18 40 75/90 MT Vacuum cup with self-locking support pg. 1.148

18 50 75/90 A Vacuum cup with self-locking support pg. 1.152
18 65 11/90 A Vacuum cup with self-locking support pg. 1.151
18 85 15 Vacuum cup with self-locking support pg. 1.145
18 85 15/90 MT Vacuum cup with self-locking support pg. 1.147
18 110 10 Vacuum cup with self-locking support pg. 1.145
18 110 10/90 MT Vacuum cup with self-locking support pg. 1.147
18 110 10/160 MT Vacuum cup with self-locking support pg. 1.149
18 120 90 Vacuum cup with self-locking support pg. 1.146
18 120 90/90 MT Vacuum cup with self-locking support pg. 1.148
18 120 90/160 MT Vacuum cup with self-locking support pg. 1.150
18 150 10 Vacuum cup with self-locking support pg. 1.145
18 150 10/90 MT Vacuum cup with self-locking support pg. 1.147
18 150 10/160 MT Vacuum cup with self-locking support pg. 1.149
18 150 75 Vacuum cup with self-locking support pg. 1.146
18 150 75/90 MT Vacuum cup with self-locking support pg. 1.148
18 150 75/160 MT Vacuum cup with self-locking support pg. 1.150
18 250 20/90 MT Vacuum cup with self-locking support pg. 1.147
18 250 20/160 MT Vacuum cup with self-locking support pg. 1.149
18 300 80/90 MT Vacuum cup with self-locking support pg. 1.148
18 300 80/160 MT Vacuum cup with self-locking support pg. 1.150
18 300 150/90 MT Vacuum cup with self-locking support pg. 1.148
18 300 150/160 MT Vacuum cup with self-locking support pg. 1.150
19 01 10 Plunger valve pg. 4.03
19 01 11 Plunger valve pg. 4.03
19 01 12 Plunger valve pg. 4.03
19 02 10 Plunger valve pg. 4.03
19 02 30 Mechanically operated valve pg. 4.04
19 03 10 Plunger valve pg. 4.03
19 04 10 Plunger valve pg. 4.03
20 04 30 Mini vacuum cup holders pg. 2.02
20 05 30 Mini vacuum cup holders pg. 2.02
20 06 30 Mini vacuum cup holders pg. 2.02
20 06 35 Mini vacuum cup holder with female connector pg. 2.17
20 06 50 Mini vacuum cup holders pg. 2.09
20 07 13 Mini vacuum cup holders with compact stroke pg. 2.19
20 07 35 Mini vacuum cup holder with female connector pg. 2.17
20 08 11 Mini vacuum cup holders with built-in bush and female connector pg. 2.24
20 08 11 M Mini vacuum cup holders with built-in bush and male connector pg. 2.24
20 08 30 Mini vacuum cup holders pg. 2.02
20 08 50 Mini vacuum cup holders pg. 2.09
20 09 30 Mini vacuum cup holders pg. 2.02
20 10 10 Mini vacuum cup holders with compact stroke pg. 2.20
20 10 11 Mini vacuum cup holders with built-in bush and female connector pg. 2.24
20 10 11 M Mini vacuum cup holders with built-in bush and male connector pg. 2.24
20 10 30 Mini vacuum cup holders pg. 2.03
20 10 38 Mini vacuum cup holder with female connector pg. 2.17
20 10 38 M Mini vacuum cup holder with male connector pg. 2.17
20 10 48 Mini vacuum cup holder with female connector pg. 2.17
20 10 48 M Mini vacuum cup holder with male connector pg. 2.17
20 10 58 M Mini vacuum cup holder with male connector pg. 2.17
20 11 16 Mini vacuum cup holders pg. 2.09
20 11 50 Mini vacuum cup holders pg. 2.09
20 12 10 Mini vacuum cup holders with compact stroke pg. 2.20
20 12 30 Mini vacuum cup holders pg. 2.03
20 12 60 Mini vacuum cup holders with plunger valve pg. 2.25
20 12 61 Mini vacuum cup holders with plung. with no springing pg. 2.35
20 12 65 Mini vacuum cup holders with plunger valve and bush pg. 2.30
20 14 15 Mini vacuum cup holders pg. 2.03
20 14 30 Mini vacuum cup holders pg. 2.03
20 15 10 Mini vacuum cup holders with compact stroke pg. 2.20

3D drawings are available on vuototecnica.net

20 15 23 Mini vacuum cup holders pg. 2.10
20 15 30 Mini vacuum cup holders pg. 2.03
20 15 60 Mini vacuum cup holders with plunger valve pg. 2.25
20 15 61 Mini vacuum cup holders with plung. with no springing pg. 2.35
20 15 65 Mini vacuum cup holders with plunger valve and bush pg. 2.30
20 16 30 Mini vacuum cup holders pg. 2.09
20 17 30 Mini vacuum cup holders pg. 2.03
20 18 10 Mini vacuum cup holders with compact stroke pg. 2.20
20 18 12 Mini vacuum cup holders pg. 2.03
20 18 23 Mini vacuum cup holders pg. 2.10
20 18 29 Mini vacuum cup holders pg. 2.10
20 18 30 Mini vacuum cup holders pg. 2.03
20 18 35 Mini vacuum cup holders pg. 2.10
20 18 50 Mini vacuum cup holders pg. 2.11
20 18 60 Mini vacuum cup holders with plunger valve pg. 2.25
20 18 61 Mini vacuum cup holders with plung. with no springing pg. 2.35
20 18 65 Mini vacuum cup holders with plunger valve and bush pg. 2.30
20 19 17 Mini vacuum cup holders pg. 2.12
20 20 10 Mini vacuum cup holders with compact stroke pg. 2.20
20 20 23 Mini vacuum cup holders pg. 2.13
20 20 30 Mini vacuum cup holders pg. 2.03
20 20 60 Mini vacuum cup holders with plunger valve pg. 2.26
20 20 61 Mini vacuum cup holders with plung. with no springing pg. 2.36
20 20 62 Mini vacuum cup holders pg. 2.11
20 20 65 Mini vacuum cup holders with plunger valve and bush pg. 2.31
20 22 10 Mini vacuum cup holders with compact stroke pg. 2.20
20 22 19 Mini vacuum cup holders pg. 2.13
20 22 30 Mini vacuum cup holders pg. 2.03
20 22 60 Mini vacuum cup holders with plunger valve pg. 2.26
20 22 61 Mini vacuum cup holders with plung. with no springing pg. 2.36
20 22 65 Mini vacuum cup holders with plunger valve and bush pg. 2.31
20 25 10 Mini vacuum cup holders with compact stroke pg. 2.21
20 25 11 Mini vacuum cup holders with built-in bush pg. 2.22
20 25 15 Mini vacuum cup holders pg. 2.04
20 25 30 Mini vacuum cup holders pg. 2.05
20 25 35 Mini vacuum cup holders pg. 2.14
20 25 60 Mini vacuum cup holders with plunger valve pg. 2.27
20 25 61 Mini vacuum cup holders with plung. with no springing pg. 2.37
20 25 65 Mini vacuum cup holders with plunger valve and bush pg. 2.32
20 27 24 Mini vacuum cup holders pg. 2.06
20 30 10 Mini vacuum cup holders with compact stroke pg. 2.21
20 30 11 Mini vacuum cup holders with built-in bush pg. 2.22
20 30 15 Mini vacuum cup holders pg. 2.04
20 30 24 Mini vacuum cup holders pg. 2.06
20 30 30 Mini vacuum cup holders pg. 2.05
20 30 32 Mini vacuum cup holders pg. 2.15
20 30 50 Mini vacuum cup holders pg. 2.16
20 30 60 Mini vacuum cup holders with plunger valve pg. 2.28
20 30 61 Mini vacuum cup holders with plung. with no springing pg. 2.38
20 30 65 Mini vacuum cup holders with plunger valve and bush pg. 2.33
20 34 26 Mini vacuum cup holders pg. 2.13
20 35 11 Mini vacuum cup holders with built-in bush pg. 2.23
20 35 15 Mini vacuum cup holders pg. 2.04
20 35 30 Mini vacuum cup holders pg. 2.05
20 35 60 Mini vacuum cup holders with plunger valve pg. 2.29
20 35 61 Mini vacuum cup holders with plung. with no springing pg. 2.39
20 35 65 Mini vacuum cup holders with plunger valve and bush pg. 2.34
20 40 11 Mini vacuum cup holders with built-in bush pg. 2.23
20 40 15 Mini vacuum cup holders pg. 2.04
20 40 42 Mini vacuum cup holders pg. 2.15
20 40 50 Mini vacuum cup holders pg. 2.16
3D drawings are available on vuototecnica.net

20 40 60 Mini vacuum cup holders with plunger valve pg. 2.29

20 40 61 Mini vacuum cup holders with plung. with no springing pg. 2.39
20 40 65 Mini vacuum cup holders with plunger valve and bush pg. 2.34
20 43 28 Mini vacuum cup holders pg. 2.15
20 45 11 Mini vacuum cup holders with built-in bush pg. 2.23
20 45 15 Mini vacuum cup holders pg. 2.04
20 45 30 Mini vacuum cup holders pg. 2.07
20 50 20 Mini vacuum cup holders pg. 2.08
20 60 30 Mini vacuum cup holders pg. 2.07
20 65 28 Mini vacuum cup holders pg. 2.08
20 70 01 Mini vacuum cup holders fix pg. 2.45
20 70 05 Mini vacuum cup holders fix pg. 2.45
20 80 05 Micro vacuum cup holders pg. 2.01
20 80 05 SR Micro vacuum cup holders without fitting pg. 2.01
20 80 05 RR Micro vacuum cup holders with quick coupling pg. 2.01
20 80 15 Mini vacuum cup holders with built-in spring pg. 2.18
20 80 20 Mini vacuum cup holders with built-in spring pg. 2.18
20 80 25 Mini vacuum cup holder with female connector pg. 2.18
20 95 08 Mini anti-rotation vacuum cup holders pg. 2.41
20 95 28 Mini anti-rotation vacuum cup holders pg. 2.42
20 95 38 Mini anti-rotation vacuum cup holders pg. 2.43
20 99 02 Mini vacuum cup holders with magnetic sensor pg. 2.44
20 99 03 Mini vacuum cup holders with magnetic sensor pg. 2.44
20 99 35 Mini vacuum cup holders with shut-off valve pg. 2.40
21 40 75 PL Vacuum cup with self-locking support pg. 1.156
21 40 75 PP Vacuum cup with self-locking support pg. 1.156
21 40 75/84 PL Vacuum cup with self-locking support pg. 1.156
21 40 75/84 PP Vacuum cup with self-locking support pg. 1.156
21 85 11/90 A Vacuum cup with self-locking support pg. 1.153
21 110 10 Vacuum cup with self-locking support pg. 1.155
21 120 90 Vacuum cup with self-locking support pg. 1.157
21 150 10 Vacuum cup with self-locking support pg. 1.155
21 150 11/90 A Vacuum cup with self-locking support pg. 1.154
21 150 75 Vacuum cup with self-locking support pg. 1.157
21 150 75/84 Vacuum cup with self-locking support pg. 1.157
22 01 10 Valve with ball shutter pg. 4.05
23 01 10 Support with striking pin pg. 1.142
23 01 15 Support with striking pin pg. 1.142
23 02 10 Support with striking pin pg. 1.142
23 05 10 Support with striking pin pg. 1.142
25 05 10 Vacuum cylinder pg. 10.23
25 10 10 Vacuum cylinder pg. 10.23
25 15 10 Vacuum cylinder pg. 10.23
AQ 32 1/8” Square adapter pg. 1.14
AQ 32 1/4” Square adapter pg. 1.14
AQ 32 1/4”F Square adapter pg. 1.14
AQ 32 3/8” Square adapter pg. 1.14
AQ 32 3/8”F Square adapter pg. 1.14
AQ 32 1/2” Square adapter pg. 1.14
AQS 32 1/8” Square adapter pg. 1.14
AQS 32 1/4” Square adapter pg. 1.14
AQS 32 3/8” Square adapter pg. 1.14
AQS 32 1/2” Square adapter pg. 1.14
AS 4 Suction and blowing system pg. 10.18
ATP 02 Pneumatic switchgear for vacuum tests pg. 11.04
ATP 03 Pneumatic switchgear for vacuum tests pg. 11.04
ATP 04 Pneumatic switchgear for vacuum tests pg. 11.04
ATS 05 Switchgear for vacuum tests pg. 11.03
ATS 20 Switchgear for vacuum tests pg. 11.03
AVG 18 Single-stage, multi-function vacuum generat. pg. 8.47 - 8.48
AVG 25 Single-stage, multi-function vacuum generat. pg. 8.47 - 8.48

3D drawings are available on vuototecnica.net

BEC 20 Bernoulli cup pg. 1.159
BEC 30 Bernoulli cup pg. 1.159
BEC 40 Bernoulli cup pg. 1.160
BEC 60 Bernoulli cup pg. 1.160
BO 08 60 X Octopus vacuum gripping bar pg. 9.22
BO 08 80 X Octopus vacuum gripping bar pg. 9.22
BO 08 100 X Octopus vacuum gripping bar pg. 9.22
BO 08 120 X Octopus vacuum gripping bar pg. 9.24
BO 12 40 X Octopus vacuum gripping bar pg. 9.23
BO 12 60 X Octopus vacuum gripping bar pg. 9.23
BO 12 80 X Octopus vacuum gripping bar pg. 9.23
BO 12 100 X Octopus vacuum gripping bar pg. 9.24
BO 12 120 X Octopus vacuum gripping bar pg. 9.24
BO 12 140 X Octopus vacuum gripping bar pg. 9.24
BT 01 Test bench and tests for the selection of vacuum cups pg. 11.10
COLL 01 03 1/2” manifold pg. 7.86
COLL 01 04 3/4” manifold pg. 7.86
COLL 01 05 1” manifold pg. 7.86
COLL 01 06 1”1/4 manifold pg. 7.86
COLL 01 07 1”1/2 manifold pg. 7.86
COLL 02 03 1/2” manifold pg. 7.87
COLL 02 05 1” manifold pg. 7.87
COLL 02 07 1”1/2 manifold pg. 7.87
COLL 03 03 1/2” manifold pg. 7.87
COLL 03 05 1” manifold pg. 7.87
COLL 03 07 1”1/2 manifold pg. 7.87
CONVY 01 Demonstration unit for the handling of powders pg. 11.11
CX 7 Vacuum Jet flow generator pg. 8.120 - 8.121
CX 10 Vacuum Jet flow generator pg. 8.120 - 8.121
CX 13 Vacuum Jet flow generator pg. 8.122 - 8.123
CX 19 Vacuum Jet flow generator pg. 8.122 - 8.123
CX 25 Vacuum Jet flow generator pg. 8.124 - 8.125
CX 38 Vacuum Jet flow generator pg. 8.124 - 8.125
CX 50 Vacuum Jet flow generator pg. 8.124 - 8.125
DDN 14 1/2” two-way solenoid valve pg. 4.21
DDN 25 1” two-way solenoid valve pg. 4.21
D2R 150 01 Degassifier pg. 11.01
D2R 150 02 Degassifier pg. 11.01
D2V 150 95V Switchgear for pump set with 2 pumps pg. 7.89
DO 06 97V Switchgear for mini pump sets pg. 7.88
DO 06 98V Switchgear for mini pump sets pg. 7.88
DO 06V VTL 2 6-litre mini pump set pg. 7.64
DO 06V VTL 2M 6-litre mini pump set pg. 7.64
DO 06V VTL 4 6-litre mini pump set pg. 7.64
DO 06V VTL 4M 6-litre mini pump set pg. 7.64
DO 06V VTL 5 6-litre mini pump set pg. 7.64
DO 06V VTL 5M 6-litre mini pump set pg. 7.64
DO 06V VTS 2 6-litre mini pump set pg. 7.63
DO 06V VTS 2M 6-litre mini pump set pg. 7.63
DO 06V VTS 4 6-litre mini pump set pg. 7.63
DO 06V VTS 4M 6-litre mini pump set pg. 7.63
DO 06V VTS 6 6-litre mini pump set pg. 7.63
DO 06V VTS 6M 6-litre mini pump set pg. 7.63
DO 10V VTL 2 10-litre mini pump set pg. 7.64
DO 10V VTL 2M 10-litre mini pump set pg. 7.64
DO 10V VTL 4 10-litre mini pump set pg. 7.64
DO 10V VTL 4M 10-litre mini pump set pg. 7.64
DO 10V VTL 5 10-litre mini pump set pg. 7.64
DO 10V VTL 5M 10-litre mini pump set pg. 7.64
DO 10V VTS 2 10-litre mini pump set pg. 7.63
DO 10V VTS 2M 10-litre mini pump set pg. 7.63
3D drawings are available on vuototecnica.net

DO 10V VTS 4 10-litre mini pump set pg. 7.63

DO 10V VTS 4M 10-litre mini pump set pg. 7.63
DO 10V VTS 6 10-litre mini pump set pg. 7.63
DO 10V VTS 6M 10-litre mini pump set pg. 7.63
DO 20V VTL 5 20-litre mini pump set pg. 7.65
DO 20V VTL 5M 20-litre mini pump set pg. 7.65
DO 20V VTL 10 20-litre mini pump set pg. 7.65
DO 20V VTL 10M 20-litre mini pump set pg. 7.65
DO 20V RVP 15 20-litre mini pump set pg. 7.65
DO 20V RVP 15M 20-litre mini pump set pg. 7.65
DO 20V RVP 21 20-litre mini pump set pg. 7.65
DO 20V RVP 21M 20-litre mini pump set pg. 7.65
DO 25V VTL 5 25 L horizontal pump set pg. 7.67
DO 25V VTL 5M 25 L horizontal pump set pg. 7.67
DO 25V VTL 10 25 L horizontal pump set pg. 7.67
DO 25V VTL 10M 25 L horizontal pump set pg. 7.67
DO 25V RVP 15 25 L horizontal pump set pg. 7.67
DO 25V RVP 15M 25 L horizontal pump set pg. 7.67
DO 50V VTL 5 50 L horizontal pump set pg. 7.67
DO 50V VTL 5M 50 L horizontal pump set pg. 7.67
DO 50V VTL 10 50 L horizontal pump set pg. 7.67
DO 50V VTL 10M 50 L horizontal pump set pg. 7.67
DO 50V RVP 15 50 L horizontal pump set pg. 7.67
DO 50V RVP 15M 50 L horizontal pump set pg. 7.67
DO 100 94 Safety switchgear for pump set with 1 pump pg. 7.91
DO 100 97V Switchgear for pump set with 1 pump pg. 7.88
DO 100 97V PLC Switchgear equipped with touch screen operator panel and plc for pump sets pg. 7.92-1
DO 100 98V Switchgear for pump set with 1 pump pg. 7.88
DO 100 98V PLC Switchgear equipped with touch screen operator panel and plc for pump sets pg. 7.92-1
DO 100V RVP 15 100 L horizontal pump set pg. 7.68
DO 100V RVP 15M 100 L horizontal pump set pg. 7.68
DO 100V RVP 21 100 L horizontal pump set pg. 7.68
DO 100V RVP 21M 100 L horizontal pump set pg. 7.68
DO 150V VTL 25/FG 150 L horizontal pump set pg. 7.68
DO 150V VTL 30/FG 150 L horizontal pump set pg. 7.68
DO 150V VTL 35/FG 150 L horizontal pump set pg. 7.68
DO 150V RVP 40 150 L horizontal pump set pg. 7.68
DO 150V VTL 50/G1 150 L horizontal pump set pg. 7.68
DO 150V RVP 60 150 L horizontal pump set pg. 7.68
DO 150V VTL 75/G1 150 L horizontal pump set pg. 7.68
DO 300V RVP 60 300 L horizontal pump set pg. 7.69
DO 300V VTL 75/G1 300 L horizontal pump set pg. 7.69
DO 300V RVP 100 300 L horizontal pump set pg. 7.69
DO 300V VTL 105/G1 300 L horizontal pump set pg. 7.69
DO 500V RVP 100 500 L horizontal pump set pg. 7.69
DO 500V VTL 105/G1 500 L horizontal pump set pg. 7.69
DO 500V RVP 160 500 L horizontal pump set pg. 7.69
DO 500V RVP 200 500 L horizontal pump set pg. 7.69
DO 500V RVP 250 500 L horizontal pump set pg. 7.69
DO 500V RVP 300 500 L horizontal pump set pg. 7.69
DO 1000V RVP 200 1000 L horizontal pump set pg. 7.70
DO 1000V RVP 250 1000 L horizontal pump set pg. 7.70
DO 1000V RVP 300 1000 L horizontal pump set pg. 7.70
DOP 06 PVP 12 MX 6 L mini pneumatic pump set pg. 8.126
DOP 06 PVP 25 MX 6 L mini pneumatic pump set pg. 8.126
DOP 10 PVP 12 MX 10 L mini pneumatic pump set pg. 8.126
DOP 10 PVP 25 MX 10 L mini pneumatic pump set pg. 8.126
DOP 20 90 Switchgear for pump sets pg. 8.133
DOP 20 PVP 25 MDX 20 L mini pneumatic pump set pg. 8.127
DOP 20 PVP 35 MDX 20 L mini pneumatic pump set pg. 8.127
DOP 25 PVP 25 MDX 25 L pneumatic pump set pg. 8.128

3D drawings are available on vuototecnica.net

DOP 25 PVP 35 MDX 25 L pneumatic pump set pg. 8.128
DOP 50 90 Switchgear for pump sets pg. 8.134
DOP 50 PVP 50 MDX 50 L pneumatic pump set pg. 8.129
DOP 50 PVP 60 MDX 50 L pneumatic pump set pg. 8.129
DOP 100 PVP 75 MDX 100 L pneumatic pump set pg. 8.130
DOP 150 90 Switchgear for pump sets pg. 8.134
DOP 150 PVP 150 MD 150 L pneumatic pump set pg. 8.131
DOP 300 PVP 300 MD 300 L pneumatic pump set pg. 8.132
DR 100 01 Degassifier pg. 11.01
DR 100 02 Degassifier pg. 11.01
DR 100 M 01 Mobile system for vacuum infusion pg. 11.02
DR 100 M 02 Mobile system for vacuum infusion pg. 11.02
DSO 300 97V Safety switchgear for pump set with 2 pumps pg. 7.89
DSO 300 97V PLC Switchgear equipped with touch screen operator panel and plc pg. 7.92-1
for safety pump sets with 2 pumps
DSO 300 98V Safety switchgear for pump set with 3 pumps pg. 7.90
DSO 300V RVP 40 300 L horiz. safety pump set pg. 7.72
DSO 300V VTL 50/G1 300 L horiz. safety pump set pg. 7.72
DSO 300V RVP 60 300 L horiz. safety pump set pg. 7.72
DSO 300V VTL 75/G1 300 L horiz. safety pump set pg. 7.72
DSO 300V RVP 100 300 L horiz. safety pump set pg. 7.72
DSO 300V VTL 105/G1 300 L horiz. safety pump set pg. 7.72
DSO 500V VTL 50/G1 500 L horiz. safety pump set pg. 7.72
DSO 500V RVP 60 500 L horiz. safety pump set pg. 7.72
DSO 500V VTL 75/G1 500 L horiz. safety pump set pg. 7.72
DSO 500V RVP 100 500 L horiz. safety pump set pg. 7.72
DSO 500V VTL 105/G1 500 L horiz. safety pump set pg. 7.72
DSO 500V RVP 160 500 L horiz. safety pump set pg. 7.72
DSO 500V RVP 200 500 L horiz. safety pump set pg. 7.72
DSO 1000V RVP 60 1000 L horiz. safety pump set pg. 7.73
DSO 1000V VTL 75/G1 1000 L horiz. safety pump set pg. 7.73
DSO 1000V RVP 100 1000 L horiz. safety pump set pg. 7.73
DSO 1000V VTL 105/G1 1000 L horiz. safety pump set pg. 7.73
DSO 1000V RVP 160 1000 L horiz. safety pump set pg. 7.73
DSO 1000V RVP 200 1000 L horiz. safety pump set pg. 7.73
DSO 1000V RVP 250 1000 L horiz. safety pump set pg. 7.73
DSO 1000V RVP 300 1000 L horiz. safety pump set pg. 7.73
DSV 150V RVP 15 150 L vert. safety pump set pg. 7.78
DSV 150V RVP 21 150 L vert. safety pump set pg. 7.78
DSV 150V VTL 25/FG 150 L vert. safety pump set pg. 7.78
DSV 150V VTL 30/FG 150 L vert. safety pump set pg. 7.78
DSV 150V VTL 35/FG 150 L vert. safety pump set pg. 7.78
DSV 300V RVP 40 300 L vert. safety pump set pg. 7.78
DSV 300V VTL 50/G1 300 L vert. safety pump set pg. 7.78
DSV 300V RVP 60 300 L vert. safety pump set pg. 7.78
DSV 300V VTL 75/G1 300 L vert. safety pump set pg. 7.78
DSV 300V RVP 100 300 L vert. safety pump set pg. 7.78
DSV 300V VTL 105/G1 300 L vert. safety pump set pg. 7.78
DSV 500V RVP 60 500 L vert. safety pump set pg. 7.79
DSV 500V VTL 75/G1 500 L vert. safety pump set pg. 7.79
DSV 500V RVP 100 500 L vert. safety pump set pg. 7.79
DSV 500V VTL 105/G1 500 L vert. safety pump set pg. 7.79
DSV 500V RVP 160 500 L vert. safety pump set pg. 7.79
DSV 500V RVP 200 500 L vert. safety pump set pg. 7.79
DSV 1000V RVP 160 1000 L vert. safety pump set pg. 7.79
DSV 1000V RVP 200 1000 L vert. safety pump set pg. 7.79
DSV 1000V RVP 250 1000 L vert. safety pump set pg. 7.79
DSV 1000V RVP 300 1000 L vert. safety pump set pg. 7.79
DSV 2000 99V Safety switchgear for pump set with 4 pumps pg. 7.90
DSV 2000V RVP 200 2000 L vert. safety pump set pg. 7.80
DSV 2000V RVP 250 2000 L vert. safety pump set pg. 7.80
3D drawings are available on vuototecnica.net

DSV 2000V RVP 300 2000 L vert. safety pump set pg. 7.80
DV 150V VTL 25/FG 150 L vertical pump set pg. 7.75
DV 150V VTL 30/FG 150 L vertical pump set pg. 7.75
DV 150V VTL 35/FG 150 L vertical pump set pg. 7.75
DV 150V RVP 40 150 L vertical pump set pg. 7.75
DV 150V VTL 50/G1 150 L vertical pump set pg. 7.75
DV 150V RVP 60 150 L vertical pump set pg. 7.75
DV 150V VTL 75/G1 150 L vertical pump set pg. 7.75
DV 300V RVP 40 300 L vertical pump set pg. 7.75
DV 300V VTL 50/G1 300 L vertical pump set pg. 7.75
DV 300V RVP 60 300 L vertical pump set pg. 7.75
DV 300V VTL 75/G1 300 L vertical pump set pg. 7.75
DV 300V RVP 100 300 L vertical pump set pg. 7.75
DV 300V VTL 105/G1 300 L vertical pump set pg. 7.75
DV 300V RVP 160 300 L vertical pump set pg. 7.75
DV 300V RVP 200 300 L vertical pump set pg. 7.75
DV 500V RVP 160 500 L vertical pump set pg. 7.76
DV 500V RVP 200 500 L vertical pump set pg. 7.76
DV 500V RVP 250 500 L vertical pump set pg. 7.76
DV 500V RVP 300 500 L vertical pump set pg. 7.76
DV 1000V RVP 200 1000 L vertical pump set pg. 7.76
DV 1000V RVP 250 1000 L vertical pump set pg. 7.76
DV 1000V RVP 300 1000 L vertical pump set pg. 7.76
DVL 150 Liquid-sucking pump set pg. 11.08
DVL 300 Liquid-sucking pump set pg. 11.08
DVL 500 Liquid-sucking pump set pg. 11.08
DVL 1000 Liquid-sucking pump set pg. 11.08
EGN 40 NC 1”1/2 two-way solenoid valve pg. 4.21-1
EGN 40 NO 1”1/2 two-way solenoid valve pg. 4.21-2
EGN 52 NC 2” two-way solenoid valve pg. 4.21-3
EGN 52 NO 2” two-way solenoid valve pg. 4.21-4
ES 01 Kit for energy saving device pg. 8.100
ES 02 Kit for energy saving device pg. 8.100
ES 05 Kit for energy saving device pg. 8.110
ES 06 Kit for energy saving device pg. 8.94
FB 1 Silencer filter pg. 8.28
FB 5 1/4” suction filter pg. 5.03 - 7.46 - 7.61
FB 10 3/8” suction filter pg. 5.04 - 7.46 - 7.61
FB 20 1/2” suction filter pg. 5.05 - 7.46 - 7.61
FB 20 A 1/2” suction filter pg. 5.06
FB 28 3/4” suction filter pg. 5.07 - 7.46 - 7.61
FB 30 1” suction filter pg. 5.08 - 7.46
FB 40 1”1/4 suction filter pg. 5.09 - 7.46
FB 50 1”1/2 suction filter pg. 5.09 - 7.46
FB 60 2” suction filter pg. 5.10
FC 10 3/8” suction filter pg. 5.12 - 7.46 - 7.61
FC 20 1/2” suction filter pg. 5.12 - 7.46 - 7.61
FC 25 3/4” suction filter pg. 5.12 - 7.46 - 7.61
FC 30 1” suction filter pg. 5.13 - 7.46
FC 35 1”1/4 suction filter pg. 5.13 - 7.46
FC 38 1”1/2 suction filter pg. 5.13 - 10.20
FC 40 1”1/4 suction filter pg. 5.14 - 7.46
FC 50 1”1/2 suction filter pg. 5.14 - 7.46
FC 55 2” suction filter pg. 5.13 - 10.20
FC 60 2” suction filter pg. 5.15 - 7.46
FC 80 3” suction filter pg. 5.15
FC 100 4” suction filter pg. 5.15
FCH 01 Fixing supp. for generators PVP 2 and 3 pg. 8.38
FCH 01 INOX Fixing supp. for generators PVP 2 and 3 pg. 8.38
FCH 02 Fixing supp. for generators 15 01/07 10 pg. 8.38
FCH 02 INOX Fixing supp. for generators 15 01/07 10 pg. 8.38

3D drawings are available on vuototecnica.net

FCH 03 Fixing supp. for generators PVP 2 and 3 pg. 8.39
FCH 03 INOX Fixing supp. for generators PVP 2 and 3 pg. 8.39
FCH 04 Fixing supp. for generators 15 01/07 10 pg. 8.39
FCH 04 INOX Fixing supp. for generators 15 01/07 10 pg. 8.39
FCH 16 Support with built-in ball joint pg. 2.168
FCL 1 1/4” in-line suction filter pg. 5.01
FCL 1 M 1/4” in-line suction filter pg. 5.01
FCL 1 MF 1/4” in-line suction filter pg. 5.02 - 10.20
FCL 2 3/8” in-line suction filter pg. 5.01
FCL 2 M 3/8” in-line suction filter pg. 5.01
FCL 2 MF 3/8” in-line suction filter pg. 5.02 - 10.20
FCL 3 1/2” in-line suction filter pg. 5.01
FCL 3 M 1/2” in-line suction filter pg. 5.01
FCL 3 MF 1/2” in-line suction filter pg. 5.02
FIR 00 SF 1/8” filter-pressure reducer pg. 10.21
FIR 03 1/2” filter-pressure reducer pg. 10.21
FK 25/7 Cont. for 3/4” coupling filtering cartridges pg. 5.27
FK 25/10 Cont. for 3/4” coupling filtering cartridges pg. 5.27
FK 30/7 Cont. for 1” coupling filtering cartridges pg. 5.27
FK 30/10 Cont. for 1” coupling filtering cartridges pg. 5.27
FK 30/20 Cont. for 1” coupling filtering cartridges pg. 5.27
FK 50/10 Cont. for 1”1/2 coupling filtering cartridges pg. 5.27
FK 50/20 Cont. for 1”1/2 coupling filtering cartridges pg. 5.27
FK 60/10 Cont. for 2” coupling filtering cartridges pg. 5.27
FK 60/20 Cont. for 2” coupling filtering cartridges pg. 5.27
FM 20/7 Cont. for 1/2” coupling filtering cartridges pg. 5.26
FM 25/7 Cont. for 3/4” coupling filtering cartridges pg. 5.26
FM 25/10 Cont. for 3/4” coupling filtering cartridges pg. 5.26
FM 30/7 Cont. for 1” coupling filtering cartridges pg. 5.26
FM 30/10 Cont. for 1” coupling filtering cartridges pg. 5.26
FM 40/10 Cont. for 1”1/4 coupling filtering cartridges pg. 5.26
FM 40/20 Cont. for 1”1/4 coupling filtering cartridges pg. 5.26
FM 50/10 Cont. for 1”1/2 coupling filtering cartridges pg. 5.26
FM 50/20 Cont. for 1”1/2 coupling filtering cartridges pg. 5.26
FM 60/10 Cont. for 2” coupling filtering cartridges pg. 5.26
FM 60/20 Cont. for 2” coupling filtering cartridges pg. 5.26
FO 20 1/2” oil-bath suction filter pg. 5.18
FO 30 1” oil-bath suction filter pg. 5.18
FO 50 1”1/2 oil-bath suction filter pg. 5.18
FO 60 2” oil-bath suction filter pg. 5.18
FO 160 1”1/2 oil-bath suction filter pg. 5.20
FO 300 2” oil-bath suction filter pg. 5.20
FP 25/4 Container for 3/4” filtering cartridges pg. 5.24
FP 25/7 Container for 3/4” filtering cartridges pg. 5.24
FP 30/4 Container for 1” filtering cartridges pg. 5.24
FP 30/7 Container for 1” filtering cartridges pg. 5.24
FP 30/4/SP Suction filter for pneumatic pumps pg. 10.20
FS 5 3/8” syphon suction filter pg. 5.21
FS 10 3/8” syphon suction filter pg. 5.21
FS 20 1/2” syphon suction filter pg. 5.21
FS 25 3/4” syphon suction filter pg. 5.21
FS 30 1” syphon suction filter pg. 5.21
FS 50 2” syphon suction filter pg. 5.21
FS 50 BP Siphon filter system with autom. by-pass pg. 5.22
FS 60 BP Siphon filter system with autom. by-pass pg. 5.22
FVG 3 Vacuum generator with ejector pg. 8.21 - 8.22
FVG 5 Vacuum generator with ejector pg. 8.21 - 8.22
FVG 8 Vacuum generator with ejector pg. 8.21-1 - 8.22-1
FVG 12 Vacuum generator with ejector pg. 8.21-1 - 8.22-1
GA FS 5 Suction unit with syphon filter pg. 11.05
GA FS 10 Suction unit with syphon filter pg. 11.05
3D drawings are available on vuototecnica.net

GA FS 20 ES Suction unit with syphon filter pg. 11.06

GA FS 25 ES Suction unit with syphon filter pg. 11.06
GA FS 30 ES Suction unit with syphon filter pg. 11.06
GAS FS 20 ES Safety suct. unit with syphon filter pg. 11.07
GAS FS 25 ES Safety suct. unit with syphon filter pg. 11.07
GAS FS 30 ES Safety suct. unit with syphon filter pg. 11.07
GR DIV 01 Support for pneumatic pumps pg. 10.19
GR DIV 02 Support for pneumatic pumps pg. 10.19
GR DIV 03 Support for small pneumatic pumps pg. 10.19
GSL 1/8” Articulated joint with axial vacuum connection pg. 2.166
GSL 1/4” Articulated joint with axial vacuum connection pg. 2.166
GSL 3/8” Articulated joint with axial vacuum connection pg. 2.166
GSL 1/2” Articulated joint with axial vacuum connection pg. 2.166
GSM 8 Articulated joint pg. 2.165
GSM 12 Articulated joint pg. 2.165
GSM 16 Articulated joint pg. 2.165
GSV 1/8” Positionable articulated joint pg. 2.167
GSV 1/4” Positionable articulated joint pg. 2.167
GSV 3/8” Positionable articulated joint pg. 2.167
GSVF 1/8” Positionable articulated joint pg. 2.167
GSVF 1/4” Positionable articulated joint pg. 2.167
GSVF 3/8” Positionable articulated joint pg. 2.167
GV 1 In-line single-stage vacuum generator pg. 8.25 - 8.26
GV 2 In-line single-stage vacuum generator pg. 8.25 - 8.26
GV 3 In-line single-stage vacuum generator pg. 8.25 - 8.26
GVMM 3 Multi-function modular vacuum generator pg. 8.70 - 8.71
GVMM 7 Multi-function modular vacuum generator pg. 8.70 - 8.71
GVMM 10 Multi-function modular vacuum generator pg. 8.72 - 8.73
GVMM 14 Multi-function modular vacuum generator pg. 8.72 - 8.73
H 35 M Mini membrane pump pg. 7.01 - 7.02
H 35 M CC Mini membrane pump with DC motor pg. 7.03 - 7.04
H 40 DM Mini membrane pump pg. 7.01 - 7.02
H 40 DM CC Mini membrane pump with DC motor pg. 7.03 - 7.04
ISO 32 Mineral oil pg. 7.47
ISO 68 Mineral oil pg. 7.47
ISO 100 Mineral oil pg. 7.47
ISO 150 Mineral oil pg. 7.47
LGS 10 NF Neoprene foam rubber sheet pg. 1.51
LGS 10 OF Foam rubber sheet pg. 1.50
LGS 10 SB Extra soft foam rubber sheet pg. 1.51
LGS 15 NF Neoprene foam rubber sheet pg. 1.51
LGS 15 OF Foam rubber sheet pg. 1.50
LGS 15 SB Extra soft foam rubber sheet pg. 1.51
LGS 20 NF Neoprene foam rubber sheet pg. 1.51
LGS 20 OF Foam rubber sheet pg. 1.50
LGS 20 SB Extra soft foam rubber sheet pg. 1.51
LGS 25 OF Foam rubber sheet pg. 1.50
LGS 30 NF Neoprene foam rubber sheet pg. 1.51
LGS 30 OF Foam rubber sheet pg. 1.50
LGS 30 SB Extra soft foam rubber sheet pg. 1.51
LGS 40 NF Neoprene foam rubber sheet pg. 1.51
LGS 40 OF Foam rubber sheet pg. 1.50
LGS 40 SB Extra soft foam rubber sheet pg. 1.51
LGS 45 OF Foam rubber sheet pg. 1.50
M3 Multi-stage vacuum generator pg. 8.52 - 8.53
M 3 SSX Multi-stage vacuum generator pg. 8.56 - 8.57
M7 Multi-stage vacuum generator pg. 8.52 - 8.53
M 7 SSX Multi-stage vacuum generator pg. 8.56 - 8.57
M 10 Multi-stage vacuum generator pg. 8.54 - 8.55
M 10 SSX Multi-stage vacuum generator pg. 8.58 - 8.59
M 14 Multi-stage vacuum generator pg. 8.54 - 8.55

3D drawings are available on vuototecnica.net

M 14 SSX Multi-stage vacuum generator pg. 8.58 - 8.59
M 18 Multi-stage vacuum generator pg. 8.54 - 8.55
M 18 SSX Multi-stage vacuum generator pg. 8.58 - 8.59
MI 3 Intermediate vacuum module pg. 8.75 - 8.76
MI 7 Intermediate vacuum module pg. 8.75 - 8.76
MI 10 Intermediate vacuum module pg. 8.77 - 8.78
MI 14 Intermediate vacuum module pg. 8.77 - 8.78
Modulo A Multi-function modules pg. 4.58 - 4.59
Modulo B Multi-function modules pg. 4.58 - 4.59
Modulo C Multi-function modules pg. 4.58 - 4.59
MSVE 3 Single-stage and multi-function vacuum generator pg. 8.40 - 8.41
MSVE 5 Single-stage and multi-function vacuum generator pg. 8.40 - 8.41
MSVE 8 Single-stage and multi-function vacuum generator pg. 8.42 - 8.43
MSVE 12 Single-stage and multi-function vacuum generator pg. 8.42 - 8.43
MSVE 20 Single-stage and multi-function vacuum generator pg. 8.44 - 8.45
MVG 3 Multi-function vacuum generator pg. 8.62 - 8.63
MVG 7 Multi-function vacuum generator pg. 8.62 - 8.63
MVG 10 Multi-function vacuum generator pg. 8.64 - 8.65
MVG 14 Multi-function vacuum generator pg. 8.64 - 8.65
NF Spanner for tightening FM filters pg. 5.26
NK Spanner for tightening FK filters pg. 5.27
NP Spanner for tightening FP filters pg. 5.24
PA 3 Small pneumatic suction pump pg. 10.03
PA 3 PS 3 Small combined pneumatic pumps pg. 10.13
PA 7 Small pneumatic suction pump pg. 10.03
PA 7 PS 7 Small combined pneumatic pumps pg. 10.13
PA 10 Small pneumatic suction pump pg. 10.04
PA 10 PS 10 Small combined pneumatic pumps pg. 10.14
PA 14 Small pneumatic suction pump pg. 10.04
PA 14 PS 14 Small combined pneumatic pumps pg. 10.14
PA 18 Small pneumatic suction pump pg. 10.04
PA 18 PS 18 Small combined pneumatic pumps pg. 10.14
PA 40 Pneumatic suction pump pg. 10.05
PA 40 PS 40 Combined pneumatic pumps pg. 10.15
PA 70 Pneumatic suction pump pg. 10.05
PA 70 PS 70 Combined pneumatic pumps pg. 10.15
PA 100 Pneumatic suction pump pg. 10.05
PA 100 PS 100 Combined pneumatic pumps pg. 10.15
PA 140 Pneumatic suction pump pg. 10.06
PA 140 PS 140 Combined pneumatic pumps pg. 10.16
PA 170 Pneumatic suction pump pg. 10.06
PA 170 PS 170 Combined pneumatic pumps pg. 10.16
PA 200 Pneumatic suction pump pg. 10.06
PA 200 PS 200 Combined pneumatic pumps pg. 10.16
PA 250 Pneumatic suction pump pg. 10.07
PA 250 PS 250 Combined pneumatic pumps pg. 10.17
PA 300 Pneumatic suction pump pg. 10.07
PA 300 PS 300 Combined pneumatic pumps pg. 10.17
PJ 07 12 Octopus bag gripping suction plate pg. 9.19
PJ 08 08 Octopus bag gripping suction plate pg. 9.19
PJ 15 20 Octopus bag gripping suction plate pg. 9.19
PJ 20 30 Octopus bag gripping suction plate pg. 9.19
PJ 20 40 Octopus bag gripping suction plate pg. 9.19
PJ 20 60 Octopus bag gripping suction plate pg. 9.19
PJ 30 40 Octopus bag gripping suction plate pg. 9.19
PJ 30 50 Octopus bag gripping suction plate pg. 9.19
PJ 40 60 Octopus bag pick-up gripping plate pg. 9.19
PS 3 Small pneumatic blowing pump pg. 10.08
PS 7 Small pneumatic blowing pump pg. 10.08
PS 10 Small pneumatic blowing pump pg. 10.09
PS 14 Small pneumatic blowing pump pg. 10.09
3D drawings are available on vuototecnica.net

PS 18 Small pneumatic blowing pump pg. 10.09

PS 40 Pneumatic blowing pump pg. 10.10
PS 70 Pneumatic blowing pump pg. 10.10
PS 100 Pneumatic blowing pump pg. 10.10
PS 140 Pneumatic blowing pump pg. 10.11
PS 170 Pneumatic blowing pump pg. 10.11
PS 200 Pneumatic blowing pump pg. 10.11
PS 250 Pneumatic blowing pump pg. 10.12
PS 300 Pneumatic blowing pump pg. 10.12
PV 08 60 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 08 80 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 08 100 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 08 120 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 12 40 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 12 60 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 12 80 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 12 100 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 12 120 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 12 140 Vacuum cup suction plate for Octopus bars pg. 9.26
PV 15 20 Vacuum cup suction plate for Octopus pg. 9.15
PV 20 30 Vacuum cup suction plate for Octopus pg. 9.15
PV 20 40 Vacuum cup suction plate for Octopus pg. 9.15
PV 20 60 Vacuum cup suction plate for Octopus pg. 9.15
PV 30 30 Vacuum cup suction plate for Octopus pg. 9.15
PV 30 40 Vacuum cup suction plate for Octopus pg. 9.15
PV 30 50 Vacuum cup suction plate for Octopus pg. 9.15
PV 40 40 Vacuum cup suction plate for Octopus pg. 9.15
PV 40 60 Vacuum cup suction plate for Octopus pg. 9.15
PV 40 100 Vacuum cup suction plate for Octopus pg. 9.15
PV 60 80 Vacuum cup suction plate for Octopus pg. 9.15
PV 60 120 Vacuum cup suction plate for Octopus pg. 9.15
PV 80 100 Vacuum cup suction plate for Octopus pg. 9.15
PV DO 35 Vacuum cup suction plate for Octopus pg. 9.15
PV DO 50 Vacuum cup suction plate for Octopus pg. 9.15
PVE 08 60 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 08 80 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 08 100 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 08 120 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 12 40 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 12 60 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 12 80 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 12 100 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 12 120 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 12 140 Vacuum cup suct. plate with shut-off valves pg. 9.28
PVE 20 30 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 20 40 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 20 60 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 30 30 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 30 40 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 30 50 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 40 40 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 40 60 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 40 100 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 60 80 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 60 120 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE 80 100 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE DO 35 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVE DO 50 Vacuum cup suct. plate with shut-off valves pg. 9.17
PVP 05 Single-stage vacuum generator pg. 8.27 - 8.28
PVP 1 In-line single-stage vacuum generator pg. 8.23 - 8.24
PVP 2 Single-stage vacuum generator pg. 8.29 - 8.30

3D drawings are available on vuototecnica.net

PVP 2M Single-stage vacuum generator pg. 8.33 - 8.34
PVP 2MM1 Single-stage vacuum generator pg. 8.33 - 8.34
PVP 2MM2 Single-stage vacuum generator pg. 8.33 - 8.34
PVP 2MM3 Single-stage vacuum generator pg. 8.33 - 8.34
PVP 3 Single-stage vacuum generator pg. 8.31 - 8.32
PVP 7 SX Single-stage vacuum generator pg. 8.35 - 8.36
PVP 7 SXLP Single-stage vacuum generator pg. 8.35 - 8.36
PVP 12 MX Multi-stage vacuum generator pg. 8.83 - 8-84
PVP 12 MXLP Multi-stage vacuum generator pg. 8.83 - 8.84
PVP 14 SX Single-stage vacuum generator pg. 8.35 - 8.36
PVP 14 SXLP Single-stage vacuum generator pg. 8.35 - 8.36
PVP 18 SX Single-stage vacuum generator pg. 8.35 - 8.36
PVP 18 SXLP Single-stage vacuum generator pg. 8.35 - 8.36
PVP 25 MDX Multi-stage vacuum generator pg. 8.95 - 8.96
PVP 25 MDXLP Multi-stage vacuum generator pg. 8.95 - 8.96
PVP 25 MX Multi-stage vacuum generator pg. 8.85 - 8-86
PVP 25 MXLP Multi-stage vacuum generator pg. 8.85 - 8.86
PVP 35 MDX Multi-stage vacuum generator pg. 8.95 - 8.96
PVP 35 MDXLP Multi-stage vacuum generator pg. 8.95 - 8.96
PVP 40 M Multi-stage vacuum generator pg. 8.87 - 8-88
PVP 40 MLP Multi-stage vacuum generator pg. 8.87 - 8.88
PVP 50 MDX Multi-stage vacuum generator pg. 8.95 - 8.96
PVP 50 MDXLP Multi-stage vacuum generator pg. 8.95 - 8.96
PVP 60 MDX Multi-stage vacuum generator pg. 8.97 - 8.98
PVP 60 MDXLP Multi-stage vacuum generator pg. 8.97 - 8.98
PVP 70 M Multi-stage vacuum generator pg. 8.87 - 8.88
PVP 70 MLP Multi-stage vacuum generator pg. 8.87 - 8.88
PVP 75 MDX Multi-stage vacuum generator pg. 8.97 - 8.98
PVP 75 MDXLP Multi-stage vacuum generator pg. 8.97 - 8.98
PVP 100 M Multi-stage vacuum generator pg. 8.87 - 8.88
PVP 100 MLP Multi-stage vacuum generator pg. 8.87 - 8.88
PVP 140 M Multi-stage vacuum generator pg. 8.89 - 8.90
PVP 140 MLP Multi-stage vacuum generator pg. 8.89 - 8.90
PVP 150 MD Multi-stage vacuum generator pg. 8.103 - 8.104
PVP 150 MDLP Multi-stage vacuum generator pg. 8.103 - 8.104
PVP 170 M Multi-stage vacuum generator pg. 8.89 - 8.90
PVP 170 MLP Multi-stage vacuum generator pg. 8.89 - 8.90
PVP 200 M Multi-stage vacuum generator pg. 8.89 - 8.90
PVP 200 MLP Multi-stage vacuum generator pg. 8.89 - 8.90
PVP 250 M Multi-stage vacuum generator pg. 8.91 - 8.92
PVP 250 MLP Multi-stage vacuum generator pg. 8.91 - 8.92
PVP 300 M Multi-stage vacuum generator pg. 8.91 - 8.92
PVP 300 MLP Multi-stage vacuum generator pg. 8.91 - 8.92
PVP 300 MD Multi-stage vacuum generator pg. 8.103 - 8.104
PVP 300 MDLP Multi-stage vacuum generator pg. 8.103 - 8.104
PVP 450 MD Multi-stage vacuum generator pg. 8.105 - 8.106
PVP 450 MDLP Multi-stage vacuum generator pg. 8.105 - 8.106
PVP 600 MD Multi-stage vacuum generator pg. 8.105 - 8.106
PVP 600 MDLP Multi-stage vacuum generator pg. 8.105 - 8.106
PVP 750 MD Multi-stage vacuum generator pg. 8.107 - 8.108
PVP 750 MDLP Multi-stage vacuum generator pg. 8.107 - 8.108
PVR 1 Cartridge vacuum generator pg. 8.115
PVR 3 OT Cartridge vacuum generator pg. 8.116
PVR 4 Cartridge vacuum generator pg. 8.115
PVR 25 Conveyor adjustable vacuum generator pg. 8.111 - 8.112 - 8.119
PVR 25 MS Conveyor vacuum generator with support for fastening to vacuum cups pg. 8.117
PVR 50 Conveyor adjustable vacuum generator pg. 8.111 - 8.112 - 8.119
PVR 100 Conveyor adjustable vacuum generator pg. 8.113 - 8.114 - 8.119
PVR 200 Conveyor adjustable vacuum generator pg. 8.113 - 8.114 - 8.119
P2H 15 20 Special suction plate for Octopus pg. 9.10-1
P2H 20 30 Special suction plate for Octopus pg. 9.10-1
3D drawings are available on vuototecnica.net

P2H 20 40 Special suction plate for Octopus pg. 9.10-1

P2H 20 60 Special suction plate for Octopus pg. 9.10-1
P2H 30 30 Special suction plate for Octopus pg. 9.10-1
P2H 30 40 Special suction plate for Octopus pg. 9.10-1
P2H 30 50 Special suction plate for Octopus pg. 9.10-1
P2H 40 40 Special suction plate for Octopus pg. 9.10-1
P2H 40 60 Special suction plate for Octopus pg. 9.10-1
P2H 40 100 Special suction plate for Octopus pg. 9.10-1
P2H 60 80 Special suction plate for Octopus pg. 9.10-1
P2H 60 120 Special suction plate for Octopus pg. 9.10-1
P2H 80 100 Special suction plate for Octopus pg. 9.10-1
P2V 15 20 Vacuum cup suction plate for Octopus pg. 9.16
P2V 20 30 Vacuum cup suction plate for Octopus pg. 9.16
P2V 20 40 Vacuum cup suction plate for Octopus pg. 9.16
P2V 20 60 Vacuum cup suction plate for Octopus pg. 9.16
P2V 30 30 Vacuum cup suction plate for Octopus pg. 9.16
P2V 30 40 Vacuum cup suction plate for Octopus pg. 9.16
P2V 30 50 Vacuum cup suction plate for Octopus pg. 9.16
P2V 40 40 Vacuum cup suction plate for Octopus pg. 9.16
P2V 40 60 Vacuum cup suction plate for Octopus pg. 9.16
P2V 40 100 Vacuum cup suction plate for Octopus pg. 9.16
P2V 60 80 Vacuum cup suction plate for Octopus pg. 9.16
P2V 60 120 Vacuum cup suction plate for Octopus pg. 9.16
P2V 80 100 Vacuum cup suction plate for Octopus pg. 9.16
P2V DO 35 Vacuum cup suction plate for Octopus pg. 9.16
P2V DO 50 Vacuum cup suction plate for Octopus pg. 9.16
P2V2E 20 30 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 20 40 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 20 60 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 30 30 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 30 40 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 30 50 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 40 40 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 40 60 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 40 100 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 60 80 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 60 120 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E 80 100 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E DO 35 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2V2E DO 50 Vacuum cup suct. plate with shut-off valv. pg. 9.18
P2X 07 12 Standard suction plate for Octopus bars pg. 9.10
P2X 08 08 Standard suction plate for Octopus bars pg. 9.10
P2X 08 60 Standard suction plate for Octopus bars pg. 9.25
P2X 08 80 Standard suction plate for Octopus bars pg. 9.25
P2X 08 100 Standard suction plate for Octopus bars pg. 9.25
P2X 08 120 Standard suction plate for Octopus bars pg. 9.25
P2X 12 40 Standard suction plate for Octopus bars pg. 9.25
P2X 12 60 Standard suction plate for Octopus bars pg. 9.25
P2X 12 80 Standard suction plate for Octopus bars pg. 9.25
P2X 12 100 Standard suction plate for Octopus bars pg. 9.25
P2X 12 120 Standard suction plate for Octopus bars pg. 9.25
P2X 12 140 Standard suction plate for Octopus bars pg. 9.25
P2X 15 20 Standard suction plate for Octopus pg. 9.10
P2X 20 30 Standard suction plate for Octopus pg. 9.10
P2X 20 40 Standard suction plate for Octopus pg. 9.10
P2X 20 60 Standard suction plate for Octopus pg. 9.10
P2X 30 30 Standard suction plate for Octopus pg. 9.10
P2X 30 40 Standard suction plate for Octopus pg. 9.10
P2X 30 50 Standard suction plate for Octopus pg. 9.10
P2X 40 40 Standard suction plate for Octopus pg. 9.10
P2X 40 60 Standard suction plate for Octopus pg. 9.10

3D drawings are available on vuototecnica.net

P2X 40 100 Standard suction plate for Octopus pg. 9.10
P2X 60 80 Standard suction plate for Octopus pg. 9.10
P2X 60 120 Standard suction plate for Octopus pg. 9.10
P2X 80 100 Standard suction plate for Octopus pg. 9.10
P2X DO 10 Standard suction plate for Octopus pg. 9.10
P2X DO 35 Standard suction plate for Octopus pg. 9.10
P2X DO 50 Standard suction plate for Octopus pg. 9.10
P2XE 08 60 Standard suct. plate with shut-off valves pg. 9.27
P2XE 08 80 Standard suct. plate with shut-off valves pg. 9.27
P2XE 08 100 Standard suct. plate with shut-off valves pg. 9.27
P2XE 08 120 Standard suct. plate with shut-off valves pg. 9.27
P2XE 12 40 Standard suct. plate with shut-off valves pg. 9.27
P2XE 12 60 Standard suct. plate with shut-off valves pg. 9.27
P2XE 12 80 Standard suct. plate with shut-off valves pg. 9.27
P2XE 12 100 Standard suct. plate with shut-off valves pg. 9.27
P2XE 12 120 Standard suct. plate with shut-off valves pg. 9.27
P2XE 12 140 Standard suct. plate with shut-off valves pg. 9.27
P2XE 20 30 Standard suct. plate with shut-off valves pg. 9.11
P2XE 20 40 Standard suct. plate with shut-off valves pg. 9.11
P2XE 20 60 Standard suct. plate with shut-off valves pg. 9.11
P2XE 30 30 Standard suct. plate with shut-off valves pg. 9.11
P2XE 30 40 Standard suct. plate with shut-off valves pg. 9.11
P2XE 30 50 Standard suct. plate with shut-off valves pg. 9.11
P2XE 40 40 Standard suct. plate with shut-off valves pg. 9.11
P2XE 40 60 Standard suct. plate with shut-off valves pg. 9.11
P2XE 40 100 Standard suct. plate with shut-off valves pg. 9.11
P2XE 60 80 Standard suct. plate with shut-off valves pg. 9.11
P2XE 60 120 Standard suct. plate with shut-off valves pg. 9.11
P2XE 80 100 Standard suct. plate with shut-off valves pg. 9.11
P2XE DO 35 Standard suct. plate with shut-off valves pg. 9.11
P2XE DO 50 Standard suct. plate with shut-off valves pg. 9.11
P2Y 15 20 Special suction plate for Octopus pg. 9.12
P2Y 20 30 Special suction plate for Octopus pg. 9.12
P2Y 20 40 Special suction plate for Octopus pg. 9.12
P2Y 20 60 Special suction plate for Octopus pg. 9.12
P2Y 30 30 Special suction plate for Octopus pg. 9.12
P2Y 30 40 Special suction plate for Octopus pg. 9.12
P2Y 30 50 Special suction plate for Octopus pg. 9.12
P2Y 40 40 Special suction plate for Octopus pg. 9.12
P2Y 40 60 Special suction plate for Octopus pg. 9.12
P2Y 40 100 Special suction plate for Octopus pg. 9.12
P2Y 60 80 Special suction plate for Octopus pg. 9.12
P2Y 60 120 Special suction plate for Octopus pg. 9.12
P2Y 80 100 Special suction plate for Octopus pg. 9.12
P2Y DO 35 Special suction plate for Octopus pg. 9.12
P2Y DO 50 Special suction plate for Octopus pg. 9.12
P2Y2E 20 30 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 20 40 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 20 60 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 30 30 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 30 40 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 30 50 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 40 40 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 40 60 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 40 100 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 60 80 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 60 120 Special suct. plate with shut-off valves pg. 9.13
P2Y2E 80 100 Special suct. plate with shut-off valves pg. 9.13
P2Y2E DO 35 Special suct. plate with shut-off valves pg. 9.13
P2Y2E DO 50 Special suct. plate with shut-off valves pg. 9.13
P2Z 15 20 Special suction plate for Octopus pg. 9.14
3D drawings are available on vuototecnica.net

P2Z 20 30 Special suction plate for Octopus pg. 9.14

P2Z 20 40 Special suction plate for Octopus pg. 9.14
P2Z 20 60 Special suction plate for Octopus pg. 9.14
P2Z 30 30 Special suction plate for Octopus pg. 9.14
P2Z 30 40 Special suction plate for Octopus pg. 9.14
P2Z 30 50 Special suction plate for Octopus pg. 9.14
P2Z 40 40 Special suction plate for Octopus pg. 9.14
P2Z 40 60 Special suction plate for Octopus pg. 9.14
P2Z 40 100 Special suction plate for Octopus pg. 9.14
P2Z 60 80 Special suction plate for Octopus pg. 9.14
P2Z 60 120 Special suction plate for Octopus pg. 9.14
P2Z 80 100 Special suction plate for Octopus pg. 9.14
P2Z DO 35 Special suction plate for Octopus pg. 9.14
P2Z DO 50 Special suction plate for Octopus pg. 9.14
PH 15 20 Special suction plate for Octopus pg. 9.10-1
PH 20 30 Special suction plate for Octopus pg. 9.10-1
PH 20 40 Special suction plate for Octopus pg. 9.10-1
PH 20 60 Special suction plate for Octopus pg. 9.10-1
PH 30 30 Special suction plate for Octopus pg. 9.10-1
PH 30 40 Special suction plate for Octopus pg. 9.10-1
PH 30 50 Special suction plate for Octopus pg. 9.10-1
PH 40 40 Special suction plate for Octopus pg. 9.10-1
PH 40 60 Special suction plate for Octopus pg. 9.10-1
PH 40 100 Special suction plate for Octopus pg. 9.10-1
PH 60 80 Special suction plate for Octopus pg. 9.10-1
PH 60 120 Special suction plate for Octopus pg. 9.10-1
PH 80 100 Special suction plate for Octopus pg. 9.10-1
PX 07 12 Standard suction plate for Octopus bars pg. 9.10
PX 08 08 Standard suction plate for Octopus bars pg. 9.10
PX 08 60 Standard suction plate for Octopus bars pg. 9.25
PX 08 80 Standard suction plate for Octopus bars pg. 9.25
PX 08 100 Standard suction plate for Octopus bars pg. 9.25
PX 08 120 Standard suction plate for Octopus bars pg. 9.25
PX 12 40 Standard suction plate for Octopus bars pg. 9.25
PX 12 60 Standard suction plate for Octopus bars pg. 9.25
PX 12 80 Standard suction plate for Octopus bars pg. 9.25
PX 12 100 Standard suction plate for Octopus bars pg. 9.25
PX 12 120 Standard suction plate for Octopus bars pg. 9.25
PX 12 140 Standard suction plate for Octopus bars pg. 9.25
PX 15 20 Standard suction plate for Octopus pg. 9.10
PX 20 30 Standard suction plate for Octopus pg. 9.10
PX 20 40 Standard suction plate for Octopus pg. 9.10
PX 20 60 Standard suction plate for Octopus pg. 9.10
PX 30 30 Standard suction plate for Octopus pg. 9.10
PX 30 40 Standard suction plate for Octopus pg. 9.10
PX 30 50 Standard suction plate for Octopus pg. 9.10
PX 40 40 Standard suction plate for Octopus pg. 9.10
PX 40 60 Standard suction plate for Octopus pg. 9.10
PX 40 100 Standard suction plate for Octopus pg. 9.10
PX 60 80 Standard suction plate for Octopus pg. 9.10
PX 60 120 Standard suction plate for Octopus pg. 9.10
PX 80 100 Standard suction plate for Octopus pg. 9.10
PX DO 10 Standard suction plate for Octopus pg. 9.10
PX DO 35 Standard suction plate for Octopus pg. 9.10
PX DO 50 Standard suction plate for Octopus pg. 9.10
PXE 08 60 Standard suct. plate with shut-off valves pg. 9.27
PXE 08 80 Standard suct. plate with shut-off valves pg. 9.27
PXE 08 100 Standard suct. plate with shut-off valves pg. 9.27
PXE 08 120 Standard suct. plate with shut-off valves pg. 9.27
PXE 12 40 Standard suct. plate with shut-off valves pg. 9.27
PXE 12 60 Standard suct. plate with shut-off valves pg. 9.27

3D drawings are available on vuototecnica.net

PXE 12 80 Standard suct. plate with shut-off valves pg. 9.27
PXE 12 100 Standard suct. plate with shut-off valves pg. 9.27
PXE 12 120 Standard suct. plate with shut-off valves pg. 9.27
PXE 12 140 Standard suct. plate with shut-off valves pg. 9.27
PXE 20 30 Standard suct. plate with shut-off valves pg. 9.11
PXE 20 40 Standard suct. plate with shut-off valves pg. 9.11
PXE 20 60 Standard suct. plate with shut-off valves pg. 9.11
PXE 30 30 Standard suct. plate with shut-off valves pg. 9.11
PXE 30 40 Standard suct. plate with shut-off valves pg. 9.11
PXE 30 50 Standard suct. plate with shut-off valves pg. 9.11
PXE 40 40 Standard suct. plate with shut-off valves pg. 9.11
PXE 40 60 Standard suct. plate with shut-off valves pg. 9.11
PXE 40 100 Standard suct. plate with shut-off valves pg. 9.11
PXE 60 80 Standard suct. plate with shut-off valves pg. 9.11
PXE 60 120 Standard suct. plate with shut-off valves pg. 9.11
PXE 80 100 Standard suct. plate with shut-off valves pg. 9.11
PXE DO 35 Standard suct. plate with shut-off valves pg. 9.11
PXE DO 50 Standard suct. plate with shut-off valves pg. 9.11
PY 15 20 Special suction plate for Octopus pg. 9.12
PY 20 30 Special suction plate for Octopus pg. 9.12
PY 20 40 Special suction plate for Octopus pg. 9.12
PY 20 60 Special suction plate for Octopus pg. 9.12
PY 30 30 Special suction plate for Octopus pg. 9.12
PY 30 40 Special suction plate for Octopus pg. 9.12
PY 30 50 Special suction plate for Octopus pg. 9.12
PY 40 40 Special suction plate for Octopus pg. 9.12
PY 40 60 Special suction plate for Octopus pg. 9.12
PY 40 100 Special suction plate for Octopus pg. 9.12
PY 60 80 Special suction plate for Octopus pg. 9.12
PY 60 120 Special suction plate for Octopus pg. 9.12
PY 80 100 Special suction plate for Octopus pg. 9.12
PY DO 35 Special suction plate for Octopus pg. 9.12
PY DO 50 Special suction plate for Octopus pg. 9.12
PY2E 20 30 Special suct. plate with shut-off valves pg. 9.13
PY2E 20 40 Special suct. plate with shut-off valves pg. 9.13
PY2E 20 60 Special suct. plate with shut-off valves pg. 9.13
PY2E 30 30 Special suct. plate with shut-off valves pg. 9.13
PY2E 30 40 Special suct. plate with shut-off valves pg. 9.13
PY2E 30 50 Special suct. plate with shut-off valves pg. 9.13
PY2E 40 40 Special suct. plate with shut-off valves pg. 9.13
PY2E 40 60 Special suct. plate with shut-off valves pg. 9.13
PY2E 40 100 Special suct. plate with shut-off valves pg. 9.13
PY2E 60 80 Special suct. plate with shut-off valves pg. 9.13
PY2E 60 120 Special suct. plate with shut-off valves pg. 9.13
PY2E 80 100 Special suct. plate with shut-off valves pg. 9.13
PY2E DO 35 Special suct. plate with shut-off valves pg. 9.13
PY2E DO 50 Special suct. plate with shut-off valves pg. 9.13
PZ 15 20 Special suction plate for Octopus pg. 9.14
PZ 20 30 Special suction plate for Octopus pg. 9.14
PZ 20 40 Special suction plate for Octopus pg. 9.14
PZ 20 60 Special suction plate for Octopus pg. 9.14
PZ 30 30 Special suction plate for Octopus pg. 9.14
PZ 30 40 Special suction plate for Octopus pg. 9.14
PZ 30 50 Special suction plate for Octopus pg. 9.14
PZ 40 40 Special suction plate for Octopus pg. 9.14
PZ 40 60 Special suction plate for Octopus pg. 9.14
PZ 40 100 Special suction plate for Octopus pg. 9.14
PZ 60 80 Special suction plate for Octopus pg. 9.14
PZ 60 120 Special suction plate for Octopus pg. 9.14
PZ 80 100 Special suction plate for Octopus pg. 9.14
PZ DO 35 Special suction plate for Octopus pg. 9.14
3D drawings are available on vuototecnica.net

PZ DO 50 Special suction plate for Octopus pg. 9.14

RA/7 Stainless steel coupling filter cartridge pg. 5.28
RA/10 Stainless steel coupling filter cartridge pg. 5.28
RA/10/57 Stainless steel coupling filter cartridge pg. 5.28
RA/20 Stainless steel coupling filter cartridge pg. 5.28
RA/20/57 Stainless steel coupling filter cartridge pg. 5.28
RF 1/8” Female fitting pg. 6.02
RF 1/4” Female fitting pg. 6.02
RF 3/8” Female fitting pg. 6.02
RL M5 L-fitting pg. 6.03
RL 1/8” L-fitting pg. 6.03
RL 1/4” L-fitting pg. 6.03
RL 3/8” L-fitting pg. 6.03
RM M5 Male fitting pg. 6.02
RM 1/8” Male fitting pg. 6.02
RM 1/4” Male fitting pg. 6.02
RM 3/8” Male fitting pg. 6.02
RP/7 Paper coupling filter cartridge pg. 5.28
RP/10 Paper coupling filter cartridge pg. 5.28
RP/10/57 Paper coupling filter cartridge pg. 5.28
RP/20 Paper coupling filter cartridge pg. 5.28
RP/20/57 Paper coupling filter cartridge pg. 5.28
RR 3/8” Quick coupling fitting pg. 6.04
RR 1/2” Quick coupling fitting pg. 6.04
RR 3/4” Quick coupling fitting pg. 6.04
RR 1” Quick coupling fitting pg. 6.04
RR 1”1/4 Quick coupling fitting pg. 6.04
RR 1”1/2 Quick coupling fitting pg. 6.04
RRF 3/8” Quick coupling fitting pg. 6.04
RRF 1/2” Quick coupling fitting pg. 6.04
RRF 3/4” Quick coupling fitting pg. 6.04
RRF 1” Quick coupling fitting pg. 6.04
RRFF 3/8” Quick coupling fitting pg. 6.04
RRFF 1/2” Quick coupling fitting pg. 6.04
RRFF 3/4” Quick coupling fitting pg. 6.04
RRFF 1” Quick coupling fitting pg. 6.04
RS 1/4” Hose end pg. 6.01
RS 3/8” Hose end pg. 6.01
RS 1/2” Hose end pg. 6.01
RS 3/4” Hose end pg. 6.01
RS 1” Hose end pg. 6.01
RS 1”1/4 Hose end pg. 6.01
RS 1”1/2 Hose end pg. 6.01
RS 3” Hose end pg. 6.01
RS/7 Polypropylene coupling filter cartridge pg. 5.28
RS/10 Polypropylene coupling filter cartridge pg. 5.28
RS/10/57 Polypropylene coupling filter cartridge pg. 5.28
RS/20 Polypropylene coupling filter cartridge pg. 5.28
RS/20/57 Polypropylene coupling filter cartridge pg. 5.28
RT 1/8” T-fitting pg. 6.03
RT 1/4” T-fitting pg. 6.03
RT 3/8” T-fitting pg. 6.03
RT M5 T-fitting pg. 6.03
RTPR 3/8” TPR flexible hose fitting pg. 6.06
RTPR 1/2” TPR flexible hose fitting pg. 6.06
RTPR 3/4” TPR flexible hose fitting pg. 6.06
RTPR 1” TPR flexible hose fitting pg. 6.06
RTPR 1”1/4 TPR flexible hose fitting pg. 6.06
RTPR 1”1/2 TPR flexible hose fitting pg. 6.06
RTPR 2” TPR flexible hose fitting pg. 6.06
RVP 15 Oil-bath vacuum pump pg. 7.30 - 7.31

3D drawings are available on vuototecnica.net

RVP 21 Oil-bath vacuum pump pg. 7.32 - 7.33
RVP 40 Oil-bath vacuum pump pg. 7.34 - 7.35
RVP 60 Oil-bath vacuum pump pg. 7.36 - 7.37
RVP 100 Oil-bath vacuum pump pg. 7.38 - 7.39
RVP 160 Oil-bath vacuum pump pg. 7.40 - 7.41
RVP 200 Oil-bath vacuum pump pg. 7.40 - 7.41
RVP 250 Oil-bath vacuum pump pg. 7.42 - 7.43
RVP 300 Oil-bath vacuum pump pg. 7.42 - 7.43
SA/4 Stainless steel filtering cartridge for FP filters pg. 5.25
SA/7 Stainless steel filtering cartridge for FP filters pg. 5.25
SFP 01 Vacuum cup holder fixing support pg. 2.169
SFP 02 Vacuum cup holder fixing support pg. 2.170
SFP 03 Vacuum cup holder fixing support pg. 2.170
SFP 04 Vacuum cup holder fixing support pg. 2.170
SFP 05 Vacuum cup holder fixing support pg. 2.170
SFP 06 Vacuum cup holder fixing support pg. 2.170
SFP 07 Vacuum cup holder fixing support pg. 2.170
SGS 10 10 OF Foam rubber strip pg. 1.50
SGS 15 10 OF Foam rubber strip pg. 1.50
SGS 20 10 OF Foam rubber strip pg. 1.50
SGS 20 15 OF Foam rubber strip pg. 1.50
SO 00 02 Flange fixing support for Octopus pg. 9.31
SO 00 05 Flange fixing support for Octopus pg. 9.31
SO 00 06 Flange fixing support for Octopus pg. 9.31
SO 07 12 X Octopus vacuum gripping system pg. 9.08
SO 08 08 X Octopus vacuum gripping system pg. 9.08
SO 15 20 MX Octopus vacuum gripping system pg. 9.04
SO 20 30 X Octopus vacuum gripping system pg. 9.05
SO 20 40 X Octopus vacuum gripping system pg. 9.05
SO 20 60 X Octopus vacuum gripping system pg. 9.05
SO 30 30 X Octopus vacuum gripping system pg. 9.06
SO 30 40 X Octopus vacuum gripping system pg. 9.06
SO 30 50 X Octopus vacuum gripping system pg. 9.06
SO 40 40 X Octopus vacuum gripping system pg. 9.06
SO 40 60 X Octopus vacuum gripping system pg. 9.06
SO 40 100 X Octopus vacuum gripping system pg. 9.07
SO 60 80 X Octopus vacuum gripping system pg. 9.07
SO 60 120 X Octopus vacuum gripping system pg. 9.07
SO 80 100 X Octopus vacuum gripping system pg. 9.07
SO DO 10 X Octopus vacuum gripping system pg. 9.08
SO DO 35 X Octopus vacuum gripping system pg. 9.09
SO DO 50 X Octopus vacuum gripping system pg. 9.09
SP/4 Paper filtering cartridge for FP filters pg. 5.25
SP/7 Paper filtering cartridge for FP filters pg. 5.25
SS/4 Polypropylene filtering cartridge for FP filters pg. 5.25
SS/7 Polypropylene filtering cartridge for FP filters pg. 5.25
SSX 1/8” Silencer pg. 8.30 - 8.32 - 8.34 - 8.101
SSX 1/4” Silencer pg. 8.06 - 8.16 - 8.101 - 9.33
10.22
SSX 3/8” Silencer pg. 8.101 - 10.22
SSX 3/8” R Silencer pg. 8.14 - 8.101
SSX 1/2” Silencer pg. 8.08 - 8.18 - 8.101 - 10.22
SSX 3/4” Silencer pg. 8.101
SSX 3/4”R Reduced silencer pg. 8.50 - 8.101
SSX 1” Silencer pg. 8.101
SSX 1”1/2 Silencer pg. 8.101
SSX 2” Silencer pg. 8.101
2SSX 1/8” Double silencer pg. 8.101
2SSX 1/4” Double silencer pg. 8.101
2SSX 3/8” Double silencer pg. 8.101
2SSX 1/2” Double silencer pg. 8.101
3D drawings are available on vuototecnica.net

2SSX 3/4” Double silencer pg. 8.101

2SSX 1” Double silencer pg. 8.101
TPL 2 Flexible tube in polyamide pg. 6.05
TPL 4 Flexible tube in polyamide pg. 6.05
TPL 6 Flexible tube in polyamide pg. 6.05
TPL 8 Flexible tube in polyamide pg. 6.05
TPL 9 Flexible tube in polyamide pg. 6.05
TPL 12 Flexible tube in polyamide pg. 6.05
TPL 16 Flexible tube in polyamide pg. 6.05
TPL 18 Flexible tube in polyamide pg. 6.05
TPR 3/8” Flexible tube in reinforced PVC pg. 6.05
TPR 1/2” Flexible tube in reinforced PVC pg. 6.05
TPR 3/4” Flexible tube in reinforced PVC pg. 6.05
TPR 1” Flexible tube in reinforced PVC pg. 6.05
TPR 1”1/4 Flexible tube in reinforced PVC pg. 6.05
TPR 1”1/2 Flexible tube in reinforced PVC pg. 6.05
TPR 2” Flexible tube in reinforced PVC pg. 6.05
VACBOT Equipped robot for gripping objects with vacuum cups pg. 11.12
VEP 30 60 Maxigrip vacuum cup pg. 1.12
VEP 30 90 Maxigrip vacuum cup pg. 1.12
VEP 40 80 Maxigrip vacuum cup pg. 1.12
VEP 50 100 Maxigrip vacuum cup pg. 1.12
VEP 60 120 Maxigrip vacuum cup pg. 1.12
VEP 70 140 Maxigrip vacuum cup pg. 1.12
VES 30 60 Maxigrip vacuum cup pg. 1.12
VES 40 80 Maxigrip vacuum cup pg. 1.12
VES 50 100 Maxigrip vacuum cup pg. 1.12
VES 70 140 Maxigrip vacuum cup pg. 1.12
VG 03 Single-stage vacuum generator pg. 8.13 - 8.14
VG 03 LP Single-stage vacuum generator pg. 8.13 - 8.14
VG 05 LP Single-stage vacuum generator pg. 8.13 - 8.14
VOP 08 24 Elliptical flat vacuum cup with male support pg. 1.44
VOP 10 30 Elliptical flat vacuum cup with male support pg. 1.44
VOP 12 36 Elliptical flat vacuum cup with male support pg. 1.44
VOP 15 45 Elliptical flat vacuum cup with male support pg. 1.44
VOP 20 60 Elliptical flat vacuum cup with male support pg. 1.44
VOP 25 75 Elliptical flat vacuum cup with male support pg. 1.44
VOP 28 85 Elliptical flat vacuum cup with male support pg. 1.44
VOP 35 100 Elliptical flat vacuum cup with male support pg. 1.44
VOP 08 24 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 10 30 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 12 36 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 15 45 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 20 60 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 25 75 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 28 85 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 35 100 F Elliptical flat vacuum cup with female supp. pg. 1.45
VOP 08 24 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 10 30 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 12 36 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 15 45 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 20 60 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 25 75 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 28 85 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOP 35 100 SR Elliptical flat vacuum cup pg. 1.44 - 1.45
VOS 08 25 Elliptical bellows vacuum cup pg. 1.46 - 1.47
VOS 15 45 Elliptical bellows vacuum cup pg. 1.46 - 1.47
VOS 25 75 Elliptical bellows vacuum cup pg. 1.46 - 1.47
VOS 08 25 F Elliptical bellows vacuum cup with female supp. pg. 1.47
VOS 15 45 F Elliptical bellows vacuum cup with female supp. pg. 1.47
VOS 25 75 F Elliptical bellows vacuum cup with female supp. pg. 1.47

3D drawings are available on vuototecnica.net

VOS 08 25 M Elliptical bellows vacuum cup with male supp. pg. 1.46
VOS 15 45 M Elliptical bellows vacuum cup with male supp. pg. 1.46
VOS 25 75 M Elliptical bellows vacuum cup with male supp. pg. 1.46
VP 12 Round Vacupredator vacuum cups pg. 1.27
VP 22 Round Vacupredator vacuum cups pg. 1.27
VP 06 12 Elliptical Vacupredator vacuum cups pg. 1.28
VP 09 16 Elliptical Vacupredator vacuum cups pg. 1.28
VP 09 21 Elliptical Vacupredator vacuum cups pg. 1.28
VP 15 20 Elliptical Vacupredator vacuum cups pg. 1.28
VP 20 30 Elliptical Vacupredator vacuum cups pg. 1.28
VP 30 40 Elliptical Vacupredator vacuum cups pg. 1.28
VPE 00 NC Pneumatic coaxial shutter valve pg. 8.37
VPE 00 NO Pneumatic coaxial shutter valve pg. 8.37
VPE 01 NC Pneumatic coaxial shutter valve pg. 8.37
VPE 01 NO Pneumatic coaxial shutter valve pg. 8.37
VPE 02 NC Pneumatic coaxial shutter valve pg. 8.37
VPE 02 NO Pneumatic coaxial shutter valve pg. 8.37
VRP 40 A Maxigrip vacuum cup pg. 1.11
VRP 50 A Maxigrip vacuum cup pg. 1.11
VRP 60 A Maxigrip vacuum cup pg. 1.11
VRP 80 A Maxigrip vacuum cup pg. 1.11
VRP 100 A Maxigrip vacuum cup pg. 1.11
VRP 125 A Maxigrip vacuum cup pg. 1.11
VRS 40 Maxigrip vacuum cup pg. 1.11
VRS 50 Maxigrip vacuum cup pg. 1.11
VRS 60 Maxigrip vacuum cup pg. 1.11
VRS 80 Maxigrip vacuum cup pg. 1.11
VRS 100 Maxigrip vacuum cup pg. 1.11
VRS 125 Maxigrip vacuum cup pg. 1.11
VSS 3/8” Suction valve pg. 4.01
VSS 1/2” Suction valve pg. 4.01
VTBOX 01 Vacuum Training Box pg. 11.09
VTL 2 Vacuum pump with lubrication pg. 7.07 - 7.08
VTL 4 Vacuum pump with lubrication pg. 7.07 - 7.08
VTL 5 Vacuum pump with lubrication pg. 7.09 - 7.10
VTL 10 Vacuum pump with lubrication pg. 7.09 - 7.10
VTL 10/FG Vacuum pump with lubrication pg. 7.13-1 - 7.14-1
VTL 15/FG Vacuum pump with lubrication pg. 7.13-1 - 7.14-1
VTL 20/FG Vacuum pump with lubrication pg. 7.13-1 - 7.14-1
VTL 25/FG Vacuum pump with lubrication pg. 7.17 - 7.18
VTL 30/FG Vacuum pump with lubrication pg. 7.17 - 7.18
VTL 35/FG Vacuum pump with lubrication pg. 7.17 - 7.18
VTL 40/G1 Vacuum pump with lubrication pg. 7.21 - 7.22
VTL 50/G1 Vacuum pump with lubrication pg. 7.21 - 7.22
VTL 65/G1 Vacuum pump with lubrication pg. 7.21 - 7.22
VTL 75/G1 Vacuum pump with lubrication pg. 7.23 - 7.24
VTL 90/G1 Vacuum pump with lubrication pg. 7.23 - 7.24
VTL 105/G1 Vacuum pump with lubrication pg. 7.23 - 7.24
VTLP 5 Vacuum pump with disposable lubrication pg. 7.11 - 7.12
VTLP 10 Vacuum pump with disposable lubrication pg. 7.11 - 7.12
VTLP 10/FG Vacuum pump with disposable lubrication pg. 7.15-1 - 7.16-1
VTLP 15/FG Vacuum pump with disposable lubrication pg. 7.15-1 - 7.16-1
VTLP 20/FG Vacuum pump with disposable lubrication pg. 7.15-1 - 7.16-1
VTLP 25/FG Vacuum pump with disposable lubrication pg. 7.19 - 7.20
VTLP 30/FG Vacuum pump with disposable lubrication pg. 7.19 - 7.20
VTLP 35/FG Vacuum pump with disposable lubrication pg. 7.19 - 7.20
VTLP 40/G1 Vacuum pump with disposable lubrication pg. 7.25 - 7.26
VTLP 50/G1 Vacuum pump with disposable lubrication pg. 7.25 - 7.26
VTLP 65/G1 Vacuum pump with disposable lubrication pg. 7.25 - 7.26
VTLP 75/G1 Vacuum pump with disposable lubrication pg. 7.27 - 7.28
VTLP 90/G1 Vacuum pump with disposable lubrication pg. 7.27 - 7.28
3D drawings are available on vuototecnica.net

VTLP105/G1 Vacuum pump with disposable lubrication pg. 7.27 - 7.28

VT OIL 32 Synthetic oil pg. 7.47
VT OIL 68 Synthetic oil pg. 7.47
VT OIL 100 Synthetic oil pg. 7.47
VT OIL FI 68 Non-toxic synthetic oil pg. 7.47
VT OIL FI 100 Non-toxic synthetic oil pg. 7.47
VTS 2 Dry vacuum pump pg. 7.48 - 7.49
VTS 4 Dry vacuum pump pg. 7.48 - 7.49
VTS 6 Dry vacuum pump pg. 7.50 - 7.51
VTS 10 Dry vacuum pump pg. 7.50 - 7.51
VTS 10/FG Dry vacuum pump pg. 7.56 - 7.57
VTS 15/FG Dry vacuum pump pg. 7.56 - 7.57
VTS 20/FG Dry vacuum pump pg. 7.56 - 7.57
VTS 25/FG Dry vacuum pump pg. 7.58 - 7.59
VTS 30/FG Dry vacuum pump pg. 7.58 - 7.59
VTS 35/FG Dry vacuum pump pg. 7.58 - 7.59
VZR 01 Ballast valve for pump RVP 21 pg. 7.33

Vacuum Pressure Ranges - Vacuum Science and Technology - Lecture 2
No ratings yet
Vacuum Pressure Ranges - Vacuum Science and Technology - Lecture 2
31 pages
Vacuum Lecture Note
No ratings yet
Vacuum Lecture Note
5 pages
Pfeiffer - Vacuum Pumps
100% (1)
Pfeiffer - Vacuum Pumps
160 pages
GLT 222 Lecture Note (Vacuum)
No ratings yet
GLT 222 Lecture Note (Vacuum)
10 pages
Vacuum Tech for Engineers
No ratings yet
Vacuum Tech for Engineers
9 pages
Vacuum Science and Technology
No ratings yet
Vacuum Science and Technology
7 pages
Edwards Vacuum Guide - Understanding The Basics
No ratings yet
Edwards Vacuum Guide - Understanding The Basics
81 pages
A Vacuum Primer: by Gary Navrotski
No ratings yet
A Vacuum Primer: by Gary Navrotski
19 pages
Edwards Vacuum Guide For Chemical Applications - Mason Technologies
No ratings yet
Edwards Vacuum Guide For Chemical Applications - Mason Technologies
81 pages
PSD CEU 194dec12 PDF
No ratings yet
PSD CEU 194dec12 PDF
22 pages
PSD CEU 194dec12 PDF
No ratings yet
PSD CEU 194dec12 PDF
22 pages
Vacuum
No ratings yet
Vacuum
4 pages
Basic Vacuum Introduction
No ratings yet
Basic Vacuum Introduction
36 pages
Design of Vacuum System
No ratings yet
Design of Vacuum System
160 pages
Vacuum Technology Basics Guide
No ratings yet
Vacuum Technology Basics Guide
41 pages
Lecture 1-2 Vacuum System
No ratings yet
Lecture 1-2 Vacuum System
113 pages
Lecture 1 110121 Vacuum System
No ratings yet
Lecture 1 110121 Vacuum System
46 pages
CH 10
No ratings yet
CH 10
21 pages
Edwards Vacuum Guide For Pharmaceutical Applications
No ratings yet
Edwards Vacuum Guide For Pharmaceutical Applications
81 pages
Vacuum Techniques Lectures Note
100% (1)
Vacuum Techniques Lectures Note
28 pages
Vacuum Theory
No ratings yet
Vacuum Theory
79 pages
Vacuum Slide Presntation PDF
No ratings yet
Vacuum Slide Presntation PDF
15 pages
Vaccum Techniques
No ratings yet
Vaccum Techniques
14 pages
Vacuum Basics
No ratings yet
Vacuum Basics
8 pages
VacuTools-Komplettkatalog e
No ratings yet
VacuTools-Komplettkatalog e
225 pages
Unit 1
No ratings yet
Unit 1
27 pages
Dekker Knowledge Database: The Experts in Vacuum Solutions
No ratings yet
Dekker Knowledge Database: The Experts in Vacuum Solutions
1 page
Vacuum Technology For Ion Sources: April 2014
No ratings yet
Vacuum Technology For Ion Sources: April 2014
41 pages
Vacmans Notes Absolute Pressure
No ratings yet
Vacmans Notes Absolute Pressure
3 pages
Chapt1 3 Experimental Physics Notes
No ratings yet
Chapt1 3 Experimental Physics Notes
21 pages
Vacuum Merged (Mid-Sem)
No ratings yet
Vacuum Merged (Mid-Sem)
30 pages
Methods of Experimental Physics Notes July2023
No ratings yet
Methods of Experimental Physics Notes July2023
70 pages
Vacuum Generation and Measurements
No ratings yet
Vacuum Generation and Measurements
56 pages
10 Vacuum Measurement
No ratings yet
10 Vacuum Measurement
54 pages
Principles of Vacuum Coating
No ratings yet
Principles of Vacuum Coating
14 pages
Vacuum Presentation
100% (2)
Vacuum Presentation
277 pages
SR-1053 Resilient Seated BFV Applications 2010-10
No ratings yet
SR-1053 Resilient Seated BFV Applications 2010-10
7 pages
Lecture 2 Notes
No ratings yet
Lecture 2 Notes
4 pages
2.water Supply Notes Continued
No ratings yet
2.water Supply Notes Continued
13 pages
Chap 2 Vacuum Physics
No ratings yet
Chap 2 Vacuum Physics
33 pages
Selected Design and Development of Vacuum Chamber
No ratings yet
Selected Design and Development of Vacuum Chamber
3 pages
WoodyFarrow Vacuum PDF
No ratings yet
WoodyFarrow Vacuum PDF
4 pages
Vacuum1 Merged
No ratings yet
Vacuum1 Merged
159 pages
Lecture 1
No ratings yet
Lecture 1
27 pages
Vacuum 1 - Basic - Concepts and Applications
No ratings yet
Vacuum 1 - Basic - Concepts and Applications
16 pages
Thermodynamics Lab Guide
No ratings yet
Thermodynamics Lab Guide
55 pages
Introduction to Vacuum Physics
No ratings yet
Introduction to Vacuum Physics
14 pages
Force Fluid Liquid Gas Pressure Vacuum
No ratings yet
Force Fluid Liquid Gas Pressure Vacuum
19 pages
Pressure Its Units of Measure and Pressure References White Paper
No ratings yet
Pressure Its Units of Measure and Pressure References White Paper
5 pages
Measuring Pressure: Technical Notes
No ratings yet
Measuring Pressure: Technical Notes
3 pages
KJLC Ed09 Sec07 Web200910
No ratings yet
KJLC Ed09 Sec07 Web200910
16 pages
Pneumax VacuumTechnology
No ratings yet
Pneumax VacuumTechnology
124 pages
Vacuum Theory and Applications
No ratings yet
Vacuum Theory and Applications
7 pages
Part 1 (Time, Mirror)
No ratings yet
Part 1 (Time, Mirror)
4 pages
LT 13 and 14
No ratings yet
LT 13 and 14
29 pages
Practical No. 3 Solution
No ratings yet
Practical No. 3 Solution
2 pages
Career Guidance for Secondary Schools
100% (2)
Career Guidance for Secondary Schools
15 pages
Physics Lab: Magnetic Force Analysis
No ratings yet
Physics Lab: Magnetic Force Analysis
3 pages
1952 Precarious Balance of John Marston
No ratings yet
1952 Precarious Balance of John Marston
11 pages
EAS Catalogue 2020
No ratings yet
EAS Catalogue 2020
193 pages
Writing Task 1 Academic Zoom 1
No ratings yet
Writing Task 1 Academic Zoom 1
76 pages
الصوت في المتاحف
No ratings yet
الصوت في المتاحف
12 pages
Financial Messaging Details
50% (2)
Financial Messaging Details
5 pages
Concerning The Detection of X-Ray Interferences: Nobel Lecture, June 3, 1920
No ratings yet
Concerning The Detection of X-Ray Interferences: Nobel Lecture, June 3, 1920
9 pages
Class 10 Math Questions 2025 - 2026
No ratings yet
Class 10 Math Questions 2025 - 2026
1 page
Olimpiada Engleză Clasa X 2018 Barem
100% (1)
Olimpiada Engleză Clasa X 2018 Barem
3 pages
Physics Syllabus For JU
No ratings yet
Physics Syllabus For JU
6 pages
How To Build A Luxury Brand and Elevated Business - Viveura
No ratings yet
How To Build A Luxury Brand and Elevated Business - Viveura
3 pages
Directorate of Erbil Construction Laboratory Borehole Log Based On ASTM D1587-00 & D6032-02
No ratings yet
Directorate of Erbil Construction Laboratory Borehole Log Based On ASTM D1587-00 & D6032-02
1 page
Deciphering King's Thesis in "Letter from Birmingham Jail"
100% (3)
Deciphering King's Thesis in "Letter from Birmingham Jail"
7 pages
IELTS Reading Practice Test
No ratings yet
IELTS Reading Practice Test
1 page
CH 3 Factors, Products and Polynomials
No ratings yet
CH 3 Factors, Products and Polynomials
14 pages
Custom Vibrational Healing Table of Contents
No ratings yet
Custom Vibrational Healing Table of Contents
2 pages
Amaecombrochure - V0.1
100% (1)
Amaecombrochure - V0.1
25 pages
Leadership Research and Development
No ratings yet
Leadership Research and Development
5 pages
Summer Vacation Homework Class 7
No ratings yet
Summer Vacation Homework Class 7
2 pages
Geological of The Baucau Quadrangle - Amuzigi
No ratings yet
Geological of The Baucau Quadrangle - Amuzigi
8 pages
Sih 1
No ratings yet
Sih 1
6 pages
HCR 1500-Ew
No ratings yet
HCR 1500-Ew
805 pages
Case Study
No ratings yet
Case Study
2 pages
Curriculum Definitions & Principles
No ratings yet
Curriculum Definitions & Principles
2 pages
Cashless Economy Class XII Term 1 Project
88% (24)
Cashless Economy Class XII Term 1 Project
30 pages
Telescopic Forks for Efficient Handling
No ratings yet
Telescopic Forks for Efficient Handling
2 pages