Released
Product Specification 03452 Version A
(Revision -, 1/2019)
70-pin platform
Small Engine Control Module Microprocessor:
ST SPC5642A, 120 MHz
SECM70 Memory: 2.0 flash, 128K
RAM, 16K serial EEPROM
Calibratable memory:
Applications 34K FLASH
The SECM70 is part of the engine management Operating voltage:
system for mobile industrial (forklift) and stationary 8–32 Vdc, 36 V (jump start),
(genset) applications. This could include 4- and 6- 5.5 V (crank)
cylinder, 4-stroke LPG/gasoline forklift applications,
and 4- and 6-cylinder, 4-stroke genset applications. Operating temperature:
-40 °C to +105 °C
The module is capable of full authority digital
engine control consisting of fuel, spark, and air Inputs:
delivery to the engine. Additional inputs and outputs
VR or digital crank position
are available to control other system functions, as
sensor
defined by software.
Digital cam position sensor
Description Up to 14 analog
The SECM70 is part of the MotoHawk® Control Solutions family of products. These Up to 5 digital
products enable rapid development of control systems. The combination of off-the-shelf (4 switch, 1 speed)
hardware and MotoHawk software allows developers to focus on the operational specifics
of the application without worrying about the design details of the hardware. The result is Up to 2 switch-type oxygen
that the same hardware used in development and prototyping efforts can be used for sensors
ongoing production.
Optional wide-range oxygen
This unit provides 70 connector pins with inputs, outputs, and communications interfaces sensor
that support a wide variety of applications.
Up to 2 knock sensors
Each controller is available in ‘F’ (Flash) or ‘C’ (Calibratable) versions. Flash modules are
typically used for production purposes. Calibratable modules are typically for Outputs:
prototyping/development only; they can be calibrated in real time using MotoTune ® or
ToolKit. 6 high-impedance injector
drivers (up to 4 low-
Physical Dimensions impedance injector drivers)
Up to 8 electronic spark-
Approximate dimensions: 190 mm x 150 mm x 47 mm triggers for smart ignition
coils
Environmental Capabilities 9 low-side drivers, 3 lamp
drivers
The environmental limits used for design validation are summarized below.
Operating Voltage 8–32 Vdc 1 main power relay driver to
Operating Temperature -40 °C to +105 °C (-40 °F to +221 °F) power engine electrical
Storage Temperature -40 °C to +105 °C (-40 °F to +221 °F) components
Mechanical Vibration RV3 (22.1 Grms)
Up to 2 H-bridge drivers for
Mechanical Shock 50 g, 11 ms, half-sine wave, 4 shocks in each direction
(24 total shocks)
electric throttle and
EMI/RFI Specification CISPR 25 (Radiated & Conducted Emissions) actuators
ISO 7637-2 (Conducted Transient Testing) Optional 3-phase brushless
ISO 10605 (ESD) DC motor driver
ISO 11452-4 (Conducted Immunity)
ISO 11452-2 (Radiated Immunity) 1 sensor supply (5 V) output
ISO 7637-3 (Transient Immunity)
ROHS 2011/65/EU Communications:
To assure that the SECM70 will perform as required, Woodward needs to review and 2 CAN 2.0b channels
approve the actual production environmental conditions to which it will be exposed.
Reference Product Manuals: 35088 Version A (SECM70 Hardware User Manual)
26784 (SECM70 Installation)
Released
Woodward 03452 p.2
For more information contact:
PO Box 1519, Fort Collins CO 80522-1519, USA
1041 Woodward Way, Fort Collins CO 80524, USA
Phone +1 (970) 482-5811 Fax +1 (970) 498-3058
Email and Website—www.woodward.com
Woodward has company-owned plants, subsidiaries, and branches, as well
as authorized distributors and other authorized service and sales facilities
throughout the world. Complete address / phone / fax / email information for
all locations is available on our website.
This document is distributed for informational purposes only. It is not to be construed as
creating or becoming part of any Woodward contractual or warranty obligation unless
expressly stated in a written sales contract.
Copyright © Woodward 2019, All Rights Reserved
