Injection Molding

– defects, causes, remedies

Tips for defect-free extrusion of
polycarbonates and their blends

1 Fault category: Part dimensions 4

2 Fault category: Ejection characteristics 9

3 Fault category: Colors 17

4 Fault category: Specks 25

5 Fault category: Surface irregularities 26

6 Fault category: Processing 31

7 Fault category: Warping 32

8 Fault category: Gloss 33

9 Fault category: Mechanical properties 41

10 Fault category: Streaking 43

Various problems can arise when extruding polycarbon-
ates and their blends. We have compiled an extensive list
of possible defects, explained their causes and described
preventive measures. To help you find them more easily,
we have divided the defects into groups, such as “Defects
caused by moisture” or “Defects commonly associated
with blown films”. Please do not hesitate to contact us if
this list does not help you solve your problem.

We would be grateful for any hints, suggestions and

illustrations you could submit to make this catalog of de-
fects more complete.
4
1 Fault category: Part dimensions
Part fails to fill properly
Description: Incomplete filling of the part, generally at the ends of flow paths
or at thin sections

Causes: Remedial actions:

Optimize processing parameters. Increase melt and mold

Unsuitable processing parameters temperature. Increase injection speed. Switch to holding
pressure at a later stage

Excessive loss of pressure in gating system (including hot Reduce pressure losses in the gating system. Enlarge gate
runner). Gate and runner cross sections too small. Excessive and runner cross sections. Check cross section of hot runner,
loss of pressure in hot runner. Excessive loss of pressure in optimize torpedo at nozzle point. Use the machine without
shut-off nozzle system shut-off nozzle

Insufficient section thickness Increase section thickness

 Variations in weight
Description: Weight and dimensions of parts vary greatly

Causes: Remedial actions:

Examine plasticizing unit and particularly non-return valve
Plasticizing unit worn
for wear

Check temperature control and heating circuits of the

Fluctuations in temperature of melt and mold
plasticizing unit

Material not thoroughly dried Check drying process

Variations in metering stroke or melt cushion Check injection stroke and metering stroke of the machine

Set clamping force higher or use a machine with a higher

clamping force too low
5 clamping force
6

Incorrect dimensions
Ist
Description: Molding fails to attain required dimensions
Soll

Causes: Remedial actions:

Excessive moisture in material Check dryness of material

Check shrinkage calculations with the aid of raw material

Shrinkage incorrectly predicted
manufacturer’s data or comparable molds

Check part and redesign for minimum warpage.

Warping caused by poor part design or gate location
Alter position of gate to ensure regular melt orientation

Check temperature control of machine and mold for thermal

Machine and mold not in thermal equilibrium
fluctuations
 Flash
Description: Thin web of material forced into crevices between mating mold
surfaces during molding and remaining attached to molded part

Causes: Remedial actions:

Gap between mold halves too wide. Locking force too small. Check gap widths. Increase locking force.
Inadequate mold rigidity. Mold sealing faces worn Increase mold rigidity. Refinish mold sealing faces

Optimize processing parameters. Reduce injection speed or

Processing parameters not optimized melt temperature. Switch from injection to holding pressure
earlier, or reduce holding pressure

Material too moist, thus viscosity reduced Check drying of material

7
8

Variations in section thickness (target/actual)

Description: Part thickness does not match up to requirements, or varies a
great deal and lies outside tolerance range

Causes: Remedial actions:

Inadequate mold rigidity Check rigidity of mold and strengthen it if necessary

Check mold dimensions and compare with raw material

Failure to allow for shrinkage, mold dimensions incorrect
manufacturer’s data on shrinkage

Reduce cavity pressure by switching from injection to hold-

Cavity pressure too high or locking force too low ing pressure at an earlier stage, reducing holding pressure
and increasing locking force

Check mold centering/guide mechanism and replace

Mold centering mechanism defective or worn
if necessary.
 2 Fault category: Ejection characteristics
Sticking sprue
Description: Sprue is constricted and/or left in the sprue bush or in the cold
runner

Causes: Remedial actions:

Optimize processing parameters. Reduce cavity pressure by
Processing parameters not ideal (e.g. timing of changeover
reducing holding pressure and switching to it earlier. Check,
from injection to holding pressure, level of holding pressure)
and if necessary, extend cooling time

Nozzle radius or aperture too large Reduce nozzle radius or aperture

Check components like injection nozzle, cold runner and

gate for undercuts and polishing effectiveness, and re-
Draft angles too small or polishing inadequate
machine in demolding direction if necessary. Optimize draft
angles and polish if necessary

Machine nozzle and sprue bush are not flush Correct position
9
10

Ejector marks
Description: Visible ejector marks on part surface

Causes: Remedial actions:

Optimize processing parameters. Reduce holding pressure
Cavity pressure too high
and switch to it earlier.

Mold stiffness not sufficient Improve mold stiffness

Cooling time too short or mold cavity temperature too high

Optimize cooling and/or mold temperature
locally
Mold design unfavorable. Undercuts too extreme, draft Optimize mold design. Reduce undercuts, improve draft
angle too low angles

Mold polishing inadequate. Positions of ejectors Optimize polishing. Check ejector positions and/or increase
unfavorable or ejector surface too small ejector surface
 Mold opening noise
Description: Mold makes a lot of noise when opened

Causes: Remedial actions:

Check mold polishing effectiveness and draft angles and re-
Draft angles too small
machine if necessary. Use a suitable mold release agent

Mold centering device defective or worn Improve mold centering

Reduce cavity pressure. Switch from injection to holding

Cavity pressure too high
pressure earlier. Reduce holding pressure
Inadequate mold rigidity Strengthen mold

Difference in temperature of mold halves too large

Differences in temperature between slides and mold Check temperatures and equalize
11 too great
12

Part remains in mold cavity – Causes

Description: Part remains in mold cavity

Causes: Remedial actions:

Reduce injection speed and holding pressure, and switch to
Mold overloaded
holding pressure at an earlier stage

Undercuts too pronounced, draft angles too small Reduce size of undercuts and improve draft angles

Mold not sufficiently polished at ribs and bosses Polish cavity surface in direction of demolding

Vacuum between mold surface and part Optimize mold venting

Premature demold: part sticks or is still too soft Increase cooling time, reduce mold temperature

Ejector pins poorly positioned or too few in number Use more ejector pins or optimize their position
 Deformation of part – Causes
Description: Part deformed during demolding

Causes: Description:
Optimize injection speed. Reduce holding pressure.
Cavity pressure too high
Switch to holding pressure at an earlier stage
Inadequate mold rigidity Strengthen mold

Cooling time too short or mold temperature too high in places Optimize cooling/mold temperature control

Poor mold design. Undercuts too pronounced, draft angles Optimize mold design. Reduce undercuts and optimze draft
too small angles
Polish mold surface in direction of demolding, choose a suitable
Mold not sufficiently polished. Ejector pins poorly positioned
surface coating or depth of texture. Optimize position and size of
or surface area too small
ejectors (in particular, locate near corners or under ribs or bosses)
13
14

Part ruptures during demolding – Causes

Description: Part damaged during demolding

Causes: Remedial actions:

Optimize injection speed. Reduce holding pressure.
Cavity pressure too high
Switch to holding pressure at an earlier stage

Inadequate mold rigidity Strengthen mold

Cooling time too long or mold temp too low in places Optimize cooling/mold temperature control

Poor mold design. Undercuts too pronounced, Optimize mold design. Reduce size of undercuts and optimize
draft angles too small draft angles
 Part ruptures during demolding – Causes

Causes: Remedial actions:

Polish cavity surface in direction of demolding, choose a suitable

Mold not sufficiently polished. Ejector pins poorly surface coating or depth of texture. Optimize position and size of
positioned or surface area too small ejector pins (it is particularly important to locate them near corners,
under ribs and bosses)

Material not adequately dried, residence time too

Check drying of material, residence time and melt temperature
long

Notch effect due to excessively sharp-edged transi-

Round off, if possible
tions
15
16

Mold will not open

Description: Even when the maximum permissible mold opening force is
applied, the mold halves cannot be separated

Causes: Remedial actions:

Reduce cavity pressure. Switch from injection to holding
Cavity pressure too high pressure sooner. Reduce holding pressure. Increase melt
temperature within acceptable limits

Inadequate mold rigidity Strengthen mold

Slide control not working Check position of slides

Note: Open mold: Use cold water to reduce temperature of mold

to room temperature, fit additional hydraulic rams between ma-
chine platens to help open mold. If necessary, raise mold tem-
perature above glass transition temperature, pull mold apart
 3 Fault category: Colors
Deeper color at weld lines
Description: Found at weld lines or near faster or slower-moving flow fronts fed
from neighboring melt streams

Causes: Remedial actions:

Pigment separation or light refraction effect caused by
Vary flow front velocity
unfavorable flow at weld lines

Thermal overloading of the melt leading to discoloration at

Reduce thermal load on the melt
weld lines

Oxidation due to insufficient venting Improve venting, possibly by relocating the weld line

Note: Tends to occur on light, bright colors such as white,

blue, green and orange
17
18

Consistent discoloration, color deviations

Description: Consistent deviation from the basic color, particularly with
light colors

Causes: Remedial actions:

Melt temperature too high Check melt temperature and reduce it if necessary

Residence time too long, because plasticizing unit not

Use a smaller plasticizing unit
working at full capacity

Unsuitable masterbatch Use a suitable masterbatch

Production interrupted without reducing temperature See notes on production stoppages

 Color inconsistencies
Description: Color inconsistencies

Causes: Remedial actions:

Material not sufficiently homogenized Increase back pressure, reduce screw speed

Injection and screw speed too high Reduce injection and screw speed

Gate too narrow Enlarge gate

Residence time too long Reduce residence time by using a smaller plasticizing unit
19
20

Rings around the gate

Description: Matt rings aligned concentrically around the gate

Causes: Remedial actions:

Stagnation of melt flow in the mold, melt temperature

Try to maintain an even melt flow, raise melt temperature
too low

Stagnation of melt flow in the mold, mold temperature too

Try to maintain an even melt flow, raise mold temperature
low

Injection rate too low Try to maintain an even melt flow, increase injection rate
 Black discoloration, burn marks, periodic discoloration
Description: Brown to black, irregular and locally variable discoloration of the
molded part

Causes: Remedial actions:

Unsuitable design of changes in cross section and bends in

Check and/or redesign the relevant components and
the hot runner, or faulty sealing faces leading to dead spots
sealing surfaces. Eliminate dead spots. Check the pressure
where the material becomes charred. Dead spots occurring
relief holes for the needle shut-off mechanism. Inspect seal-
at sealing faces, changes in cross section and bends in the
ing faces
hot runner

Check the screw, the non-return valve and the cylinder for
Wear on the screw, the non-return valve or the cylinder
wear
21
22

Blackening, Diesel effect

Description: Concentrated blackening at weld lines, e.g. near ribs or bosses,
or in corners at the end of flow paths

Causes: Remedial actions:

Optimize mold venting, particularly where flow fronts

meet and at the end of flow paths. Correct flow front profile
Entrapped, compressed air in the mold leading to scorching by adjusting section thickness, gate location or using flow
leaders. Check venting channels. Reduce mold locking force.
Evacuate mold

Note: In addition to optical degradation of the molded part,

this fault can also damage the mold through corrosion
 Stress whitening
Description: Areas of lighter color combined with a velvety matt part surface

Causes: Remedial actions:

Overstretching of the polymer matrix. Excessive mechanical Reduce mechnical stress during ejection.
stress during ejection. Poorly positioned ejector pins and Correct positions of ejectors, e.g. position ejectors at stress
draft angles too small whitening lines

Excessive stress in service Lower stresses in service

Cavity pressure too high. Inadequate mold rigidity Lower cavity pressure. Strengthen mold rigidity

Note: Fault mostly occurs with thermoplastics containing

rubber
23
24

Cloudiness, grey streaks

Description: Dark, cloudy areas on part surface

Causes: Remedial actions:

Plasticizing unit contaminated Clean plasticizing unit. Reduce screw speed

Replace complete plasticizing unit or individual components.

Wear on the plasticizing unit
Use a corrosion- and abrasion-resistant plasticizing unit

Optimize cylinder temperature, circumferential speed of the

Melt load too high
screw, back pressure
 4 Fault category: Specks
Brown or black spots
Description: Sporadically occurring specks, either spherical with irregular
outlines or like platelets with clearly defined, straight outlines

Causes: Remedial actions:

Clean the plasticizing unit mechanically. See recommended

Tearing or peeling off of thin layers of melt which form on
procedure for production stoppages. Check plasticizing unit
the surface of the cylinder and the screw
for wear

Check granules for possible contamination. Store granules

in a dust-free place. Clean contaminated post-consumer
Contamination of the granules/regrind articles before regrinding. Do not regrind damp or thermally
damaged articles. Check the drying and feed systems for
contamination
25
26
5 Fault category: Surface irregularities
Blisters
Description: Solid, round or elongated bumps or lumps on the surface which are re-
stricted to very small areas and are not necessarily visible on both sides of the molded part

Causes: Remedial actions:

Unmelted material, or air drawn in during metering:
Use a suitable screw
+ screw cut too deep
Unmelted material, or air drawn in during metering:
Keep metering stroke to between 1 and 3D
+ metering stroke exceeds 3D
Unmelted material, or air drawn in during metering:
Increase back pressure
+ back pressure too low
Unmelted material, or air drawn in during metering:
Raise melt temperature
+ melt temperature too low
Unmelted material, or air drawn in during metering:
Reduce screw speed
+ screw speed too high
 Delamination
Description: Separation or flaking off of surface material, either over the entire
molding or locally near the sprue

Causes: Remedial actions:

Excessive shear stress. Gate too thin.
Reduce shear stress. Widen gate. Reduce injection speed
Injection speed too high

Clean plasticizing unit. Check material in hopper and feed

Contamination caused by incompatible resins
lines for contamination by other materials

Unsuitable pigment masterbatch Use a suitable pigment masterbatch

27
28

Localized sink marks

Description: Distinct, localized hollows in the surface, generally found opposite
ribs, at thicker sections, cores, weld lines, constrictions, hot runner nozzles and
the end of flow paths

Causes: Remedial actions:

Compensate for volume contraction: Adjust wall thickness/

rib thickness ratio to suit material, increase holding pres-
No compensation for volume contraction during the cooling sure and holding pressure time, increase nozzle aperture
phase and gate cross section. Reduce temperature of melt and tool
(may lead to voids). Check melt cushion. Conceal sink marks
if necessary
 Notches along weld line, pronounced weld line
Description: Tangible or visible notch along the weld line

Causes: Remedial actions:

Insufficient mold venting Improve mold venting, especially at end of flow path

Improve flow properties by increasing temperature of melt

Inadequate flow properties of the resin. Injection speed too
and mold. Raise injection speed. Increase section thickness
low. Walls too thin or flow paths too long
or, if necessary, relocate gate so as to shorten flow paths

Note: Mostly with high-viscosity or quick-setting thermo-

plastics. In many cases, variotherm methods can be used to
conceal the weld line
29
30

Grooves, record grooves, stick-slip effect

Description: Fine, concentric grooves around the sprue; grooves parallel to the
flow front in thin-walled areas

Causes: Remedial actions:

Pulsating melt flow in the mold, caused by excessive cooling
Try to maintain an even, rapid melt flow
of the flow front, cause:

injection speed too low Increase injection speed

melt temperature too low Raise melt temperature

mold temperature too low or Raise mold temperature

walls too thin Increase wall thickness

 6 Fault category: Processing
Melt cushion varies in size
Description: Size of melt cushion fluctuates widely, becoming almost non-existent
at times

Causes: Remedial actions:

Non-return valve defective or worn Check non-return valve and replace if necessary

Check cylinder bore for wear and insert a sleeve if necessary,

Irregular metering
or use a new plasticizing unit

31
32
7 Fault category: Warping
General warping
Description: Molded parts do not match specification drawing, suffer warpage
at corners or do not fit accurately

Causes: Remedial actions:

Part poorly designed. Unsuitable orientation of glass fibers. Optimize part design. Improve orientation of glass fibers by
Unsuitable distribution of wall thickness optimizing gate. Optimize distribution of wall thickness

Switch from injection to holding pressure at a later stage.

Holding pressure ineffective. Non-return valve worn
Inspect non-return valve and replace if necessary

Note: All possible causes of defect, associated remedies and

their interdependencies are too complex to go into here
 8 Fault category: Gloss
Frosting
Description: Rough, matt part surfaces of the edges

Causes: Remedial actions:

Injection speed too low Raise injection speed

Raise the temperature of the mold. Fit thermal insulation

Mold temperature too low
round mold. Use a more efficient temperature control unit

Note: Only affects glass-fiber-reinforced thermoplastics.

Very evident on amorphous thermoplastics, less so on semi-
crystalline thermoplastics
33
34

Poor gloss with polished surfaces

Description: Part does not meet gloss requirements (either over the whole
surface or in a certain area)

Causes: Remedial actions:

Mold worn or not properly polished Polish mold thoroughly

Injection speed too low, possibly due to poor venting Increase injection speed, if necessary by improved venting

Fluctuations in mold temperature caused by inadequate

Check consistency of mold temperature
cooling

Material not properly dried Check drying process

Improve effectiveness of holding pressure by increasing

Holding pressure ineffective holding pressure, extending holding pressure time and if
necessary increasing gate size
 Variations in gloss on the surface of the molded article
Description: Variations in gloss over all or part of the surface of the article

Causes: Remedial actions:

Injection speed too low Raise injection speed

Cavity surface worn or corroded Re-machine mold surface

Service the temperature control system and eliminate any

Fluctuations in mold temperature. Problems in the tempera- leaks. Improve temperature control by adding more heating-
ture control circuit, e.g. leakage, blocked cooling channel, cooling channels, increasing the throughput of the tempera-
temperature control unit defective ture control medium or changing the medium (e.g. use water
instead of oil)

Springy mold elements, such as cores or ejectors Increase mold rigidity

35
36

Localized, glossy, finger-shaped depressions

Description: Glossy depressions, often near the sprue, at cores or in the
vicinity of hot runner units

Causes: Remedial actions:

Premature demold Extend cycle time

Increase holding pressure, increase holding pressure time,

Holding pressure too low and holding pressure time too
check melt cushion, check, and if necessary increase nozzle
short
aperture and gate cross section

Switch from injection to holding pressure made too soon Switch to holding pressure at a later stage

Reduce mold temperature locally by means of additional

Mold temperature too high in places
cooling channels or separate temperature control

Note: See also: Matt surface defects

 Dull spots, matt patches
Description: Uniform, clearly defined velvety areas on surface

Causes: Remedial actions:

Even out differences in flow front velocities by improv-

Flow fronts with different velocities (with several gating
ing the balance of the gating system (where several feed
points)
points are involved)

Round off or polish transition zones and abrupt changes in

Tearing of already solidified outer skin at sharp bends and
wall thickness in the runner and mold; balance flow front
abrupt changes in wall thickness
velocities

Note: See also: Flaking

37
38

Matt surface defects near hot runner units

Description: Matt surface defects near hot runner units

Causes: Remedial actions:

Premature demold Increase cooling time

Improve thermal isolation of hot runners, reduce mold tem-

Mold temperature at hot runner too high
perature

Core temperature too high Make sure core is adequately cooled

 Poor matt effect on textured surfaces
Description: Part surface does not meet mattness requirements

Causes: Remedial actions:

Injection speed and mold temperature too low Increase injection speed and mold temperature

Holding pressure ineffective Switch to holding pressure at a later stage and increase its level

Surface texture of mold cavity poor or worn Re-machine mold surface

39
40

Damaged grain on the molded article

Description: Rough, torn surface with grooves in the direction of demolding,
mostly at the same place

Causes: Remedial actions:

Draft angles too small Increase draft angles

Mold surface damaged Re-machine mold surface

Reduce cavity pressure. Switch from injection to holding

Cavity pressure too high pressure earlier. Reduce holding pressure. Optimize injection
rate. Increase melt temperature within acceptable limits

Inadequate mold rigidity Strengthen mold

Note: Scoring can often only be identified using optical aids

 9 Fault category: Mechanical properties
Inadequate weld line strength
Description: Failure of part near weld line

Causes: Remedial actions:

Insufficient mold venting Improve mold venting

Improve flow properties. Increase injection speed. Raise

Inadequate flow properties of the resin. Injection speed too
melt and mold temperature. Increase wall thickness or
low. Walls too thin or flow paths too long
relocate gates so as to shorten flow paths

41
42

Mechanically defective part

Description: Part unable to withstand mechanical stress

Causes: Remedial actions:

Check design against mechanical requirements.
Mechanical stress too high
(internal stress, resistance of the resin to various media)

Degradation of the material caused by faulty drying or Monitor melt temperature, residence time and drying
thermal overloading process

Unsuitable position of weld line Locate weld lines away from main areas of stress

Prevent part from being damaged during demold, improve

Poor ejection characteristics at screw bosses etc.
ejection characteristics
 10 Fault category: Streaking
Cold flow marks, flaking
Description: Surface appears flaky with alternating glossy and matt areas,
mostly near the sprue

Causes: Remedial actions:

Inject material in stages, starting slowly and gradually

Displacement of material which has already cooled increasing speed. Reduce mold temperature. Design gates
with radii and polish them

43
44

Jetting
Description: Generally serpentine strand of the melt first injected into the mold,
found near the sprue or at constricted sections, and visible on the part surface

Causes: Remedial actions:

Unsuitable design of gate or narrow sections preventing

Redesign gate. Position gate opposite a wall. Enlarge gate
laminar flow. Gate position with no opposing wall. Gate
cross section. Redesign changes in cross section
cross section or narrow section too small

Injection speed too high Inject material slowly at first, then switch to a faster speed
 Large-area silver streaks
Description: Brush-shaped, elongated streaks spread over a large area

Causes: Remedial actions:

Use a larger plasticizing unit to reduce the length of the
metering stroke (<3D). If plasticizing unit cannot be
changed: Increase temperature of feed section, reduce
Metering stroke of the plasticizing unit too long
screw speed, increase cycle time and, as an additional, op-
tional measure, increase the melt cushion by 1–2 D if
possible

Optimize plasticizing conditions. Increase back pressure

Air entrainment during metering (within acceptable limits). Reduce screw retraction. Position
injection nozzle tight up against hot runner mold

Note: Sometimes occurs in association with blistering

45
46

Knuckle line
Description: When light falls on the part from a certain angle, a line or shim-
mer can clearly be seen on its surface, frequently at weld lines, ribs, abrupt
changes in section thickness or splits

Causes: Remedial actions:

Elastic deformation of sliding cores Improve slide supports or increase mold rigidity

Alter position of weld lines, if necessary by changing

Glass fibers perpendicular to flow direction at weld lines
location or number of gates

Abrupt changes in stiffness at ribs or where section Avoid abrupt changes in wall thickness in favor of gradual
thickness changes transitions
 Surface marred by linear grooves, scratches
Description: Grooves and scratches running in the demolding direction, also
visible as matt streaks on high-gloss surfaces

Causes: Remedial actions:

Check cavity surface and re-machine if necessary, polish in
Cavity surface damaged
demolding direction
Elastic deformation of sliding cores Optimize sliding cores

Reduce cavity pressure. Switch from injection to holding pressure

Cavity pressure too high earlier. Reduce holding pressure. Optimize injection rate. Increase
melt temperature within acceptable limits

Inadequate mold rigidity Strengthen mold

47 Note: See also: Mold opening noise

48

U-shaped streaks, moisture streaks

Description: Elongated, pencil-like streaks, open towards the flow direction:
in mild cases may be single streaks

Causes: Remedial actions:

Check drying process (temperature, time and hourly

Residual moisture content of pellets too high throughput). Examine dryer filter for contamination. Check
direction of rotation of drive motor
 Overheating streaks, silver streaks
Description: Elongated silver streaks

Causes: Remedial actions:

Excessive thermal load on the melt: Reduce the thermal load on the melt,
melt temperature too high Reduce melt temperature
Excessive thermal load on the melt: Reduce the thermal load on the melt,
melt residence time too long use a smaller screw diameter
Excessive thermal load on the melt: Reduce the thermal load on the melt,
screw speed too high reduce screw speed
Excessive thermal load on the melt: Reduce the thermal load on the melt,
nozzle and flow channel cross sections too small widen nozzle and runner diameter
Excessive thermal load on the melt: Reduce the thermal load on the melt,
failure to reduce temperature during a break in production see notes on production stoppages

49 Note: Often appears similar to moisture streaks

50

Large bubbles
Description: Air-filled bubbles in the walls

Causes: Remedial actions:

Check granule feed for air entrainment. Increase holding

Air entrainment during metering pressure (within acceptable limits). Reduce screw retraction
(suck back)

Use a plasticizing unit one size larger if the screw stroke is

Capacity of plasticizing unit exceeded
greater than 3D
 Cold slug, cold flow marking, irregular matt area
Description: Cold material trapped at the molded-part surface

Causes: Remedial actions:

Cold slug well in cold runner absent or too small Incorporate or improve cold slug well

Speed up screw retraction, improve thermal isolation in hot

Escape of material from injection nozzle or hot runner
runner

Increase size of nozzle aperture, install a more powerful

Nozzle aperture too small, nozzle temperature too low
heater band, check thermocouple and regulator
51
52

Small bubbles
Description: Entrapped air similar to voids, but very much smaller diameter
and more numerous

Causes: Remedial actions:

Excessive moisture in material Check drying process

Select a suitable vented screw or substitute a conventional

Unsuitable venting unit
screw for the vented screw and pre-dry the material

Note:
Often occurs in conjunction with extensive silver streaks
 Tear drops
Description: Tear drop-shaped irregularities caused by entrapped air

Causes: Remedial actions:

Reduce injection speed in the critical area. Improve mold

Air trapped in the mold, e.g. in engraved areas, grooves or
venting at weld lines and depressions, ribs and engraved
depressions
areas. Apply a vacuum to the mold

53
54

Craters, pinholes, dimples

Description: Depressions as small as a pinhead

Causes: Remedial actions:

Material degradation Reduce melt temperature and residence time

Faulty pigmentation (using incompatible pigments in in-plant

Use compatible pigments or a different type of carbon black
coloring, e.g. the wrong type of carbon black)

Too much carbon black Reduce carbon black content

Mold temperature too low Raise mold temperature significantly

 Grey specks, metallic specks
Description: Grey foreign particles which appear shiny when lit from certain
angle.

Causes: Remedial actions:

Plasticizing unit worn Check for wear on screw, cylinder and non-return valve

Check feed pipes, containers and hoppers for abrasion. Use

Foreign particles produced by abrasion of feed pipes, stainless steel for feed pipes, containers and hoppers, alu-
containers and hoppers minum and tinplate are unsuitable. Avoid corners as far as
possible. If not, design them with large radii

Carry out regular maintenance on granulators and check for

Granulator for regrind worn
abrasion and damage
55
56

Microscopic cracks, micro-cracks

Description: Microscopic cracks in the part, often occuring only at the surface
where outer fibres are under tensile stress

Causes: Remedial actions:

Optimize processing parameters with a view to reducing

Excessive stress in the part stress. Increase temperature of mold and melt. Re-design
part so as to reduce long-term outer fiber strain

Check compatibility with various media. Check stress-crack-

inducing effect of release and anti-corrosive agents. Test
Contact with unsuitable media part for chemical resistance to cleaning fluids and degreas-
ing agents. Check part’s resistance to media encountered in
practical use and reduce mechanical load if necessary
 Voids, bubbles, vacuoles
Description: Round or elongated bubbles generally only visible in transparent
and translucent parts

Causes: Remedial actions:

Increase holding pressure, increase holding pressure time,
No compensation for volume contraction during the cooling
check melt cushion, check, and if necessary increase nozzle
phase. Holding pressure ineffective
aperture and gate cross section

No compensation for volume contraction during the cooling Locate gate in a thick wall section. Revise part design so as
phase. Injection point poorly positioned, or part badly designed to avoid abrupt changes in wall thickness

Note: Comply with design guidelines for injection-molded

parts
57
58

Stringing
Description: Long, thin threads emerge from the machine or hot runner nozzle

Causes: Remedial actions:

Nozzle aperture too large Select a smaller nozzle aperture, but remember critical shear

Optimize thermal isolation at the nozzle point. Reduce

Poor thermal isolation at the nozzle point. Temperature of
nozzle temperature. Activate suck-back or increase retrac-
the nozzle point where it meets the hot runner too high.
tion distance (after metering in the case of machine nozzles,
Insufficient suck-back
before metering in the case of hot runner nozzles)

Nozzle temperature too high at breaking point Reduce nozzle temperature

Insufficient screw retraction Activate screw retraction or increase retraction distance

This information and our technical advice – whether
verbal, in writing or by ways of trial – are given in good
faith but without warranty, and this also applies where
proprietary rights of third parties are involved.
The information is provided by Bayer  MaterialScience
AG without assumption of any liability. If any of the
above mentioned regulations change after the date
of declaration, this declaration is no longer valid.
Bayer MaterialScience AG will strive to keep this infor-
mation up-to-date.
Our advice does not release you from the obligation
to verify the information provided – especially that
contained in our safety data and technical information
sheets –, to check for updates of any information pro-
vided by us and to test our products as to their suitabili-
ty for the intended processes and uses. The application,
use and processing of our products and the products
manufactured by you on the basis of our technical ad-
vice are beyond our control and, therefore, entirely your
own responsibility.
Our products are sold in accordance with the current
version of our General Conditions of Sale and Delivery.

Edition: 2011-09
Order-no.: MS00056040 Printed in Germany · E
Bayer MaterialScience AG
51368 Leverkusen
Germany

www.plastics.bayer.com