& SLICK — sx220¢ Service Bulletin To: SUBJECT: BACKGROUND INFORMATION: COMPLIANCE: PROOF OF COMPLIANCE: MODELS AFFECTE! Aircraft Manufacturers, Aircraft Engine Manufacturers, Distribu- tors, Dealers, Engine Overhaul Facilities, Owners and Operators of Slick Aircraft Magnetos. Magneto Maintenance and Overhaul Schedules. The service and warranty history of Slick magnetos clearly show that the prescribed maintenance and overhaul schedules found in Slick Maintenance and Overhaul manuals L-1020, L-1037, and L- 1363 are not being followed. Failure to properly perform the prescribed inspections, maintenance, and overhaul procedures Voids Slick warranty and may jeopardize the airworthiness of these ‘components resulting in possible serious equipment damage, personal injury, or loss of life. ALL AGENCIES OR INDIVIDUALS SERVICING ANY COMPO- NENT MADE BY SLICK AIRCRAFT PRODUCTS MUST HAVE THE MOST CURRENT REVISIONS OF SLICK MASTER SER- VICE MANUAL F-1100 BEFORE PERFORMING MAINTE- NANCE OR OVERHAUL. CONSULT SLICK REGARDING SUB- SCRIPTION SERVICE INFORMATION. As required. Appropriate log book entries. All 400 and 600 series magnetos 4000 and 4100 series magnetos 4200 and 6200 series magnetos 4300 and 6300 series magnetos MAINTENANCE PARTS AFFECTED: None PARTS REQUIRED PER BULLETIN: None TOOLS REQUIRED PER BULLETI None ISSUED REVISED "Slick Aircraft Products PAGEN( ‘AY |v | wo | ony [vean SS 01 | 80] 04 | 01 | 91 Unison Industries 530 Blackhawk Park Avenue sazs| 01 oF 04 Rockford, Illinois, U.S.A. 61104 IndustriesSB2-80C SLICK Service Bulletin FAA APPROVED WEIGHT CHANG! None DETAILED INSTRUCTIONS: 400 AND 600 SERIES MAGNETOS — REFERENCE MANUAL L-1020 1. INSPECTION These magnetos should be inspected externally every 100 hours and internally every 500 hours. Consult Manual L-1020 for complete Inspection procedures. i, ADDITIONAL SERVICE INFORMATION Slick Service Bulletins and Service Letters contain service information criticalto the airworthiness and operation of particular magneto models. Consult the most current revision of Slick Master Service Manual F- 1100 for applicability of special service information to particular mag- neto models. OVERHAUL These magnetos should be completely overhauled as required by the inspections noted above. Total time in service may not exceed the manufacturer's TBO for the engine on which the magneto is installed. When servicing magnetos use only the most current revision of Slick manufactured parts. In most cases it may be easier to replace a faulty magneto with a new, current production, factory assembled 4300 or 6300 Series magneto than to perform the overhaulin the field. Factory assembled new and rebuilt 400 and 600 Series magnetos have been discontinued and are no longer available from Slick. IV. REPLACEMENT These magnetos should be replaced as necessary when indicated by the above inspections. 4000 / 4100 SERIES MAGNETOS: |. INSPECTION At each 200 hour interval the following inspections should be made: 1. Adjust timing to engine 2. General Inspection a. Wiring connections and condition b. Vent holes c. P-lead attachment |. OVERHAUL These magnetos are certified by the FAA as factory-sealed and no attempt should be made to overhaul or repair them in the field. Replacement parts and service information are unavailable for these magnetos. They are to be exchanged completely for new current production repairable 4300 Series magnetos. ISSUED REVISED Slick Aircraft Products PAGENO. || REVISION we | onr[ va | wo | ony | vena! Unison Industries aalraultaa aaliailse 530 Blackhawk Park Avenue Bie] 02 OF oF Rockford, ilinois, U.S.A. 61104 IndustiesSLICK Service Bulletin $82;80C removed from service and replaced. However, service history of these magnetos indicate they have been routinely run in excess of 800 hours and in many cases are not serviced until an operational or mechanical failure occurs. The abuse to which these magnetos have been sub- jected has forced Slick to re-establish parameters for time in operation of 4000/4100 Series magnetos. EFFECTIVE IMMEDIATELY: WITHIN THE NEXT 100 HOURS OF OPERATION OR AT NEXT SCHEDULED ANNUAL INSPECTION. ALL 4000 AND 4100 SERIES MAGNETOS WITH TIME INSERVICE GREATER THAN 800 HOURS MUST BE REPLACED WITH THE APPROPRIATE SLICK MODEL 4300 SERIES MAGNETO. 4200 / 6200 SERIES MAGNETOS — REFERENCE MANUAL L-1037 1. INSPECTION | ‘These magnetos should be inspected externally every 100 hours and internally every 500 hours. Magneto rotor shaft bearings must be replaced every 1000 hours. Consult latestrevision of ManualL-1037 for complete inspection procedures. i, ADDITIONAL SERVICE INFORMATION Slick Service Bulletins and Service Letters contain service information critical to the airworthiness and operation of particular magneto models. Consult the most current revision of Slick Master Service Manual F- 1100 for applicability of special service information to particular mag- neto models. MW. OVERHAUL These magnetos should be completely overhauled as required by the inspections noted above. Total time in service may not exceed the manufacturer's TBO for the engine on which the magneto is installed. When servicing magnetos use only the most current revision of Slick manufactured parts. In most casesit may be easier and more economi- cal to replace a faulty magneto with a new current production factory assembled unit than to perform the overhaul in the field. Iv. REPLACEMENT ‘These magnetos should be replaced as necessary when indicated by the above inspections. | Ml, REPLACEMENT These magnetos were designed to provide reliable service up to 800 hours. At 800 hours it was recommended that these magnetos be 4 Ss é ISSUED __[_ REVISED Slick Aircraft Products PAGENO. [| REVISION ony [ww wo | ony [wean Unison Industies 530 Blackhawk Park Avenue ©1991 03 OF 04 c pet he [inet be Rockford, linois, U.S.A. 61104 inant A; SIVIVIVITIVITIVIVITITITTITITISTTTITASITIT TIT /,SLICK Service Bulletin £82;89C 4300 / 6300 SERIES MAGNETOS — REFERENCE MANUAL L-1363 1. INSPECTION These magnetos should be inspected externally every 100 hours and internally every 500 hours. Consultlatest revision of Manual L-1363 for complete inspection procedures. Ul. ADDITIONAL SERVICE INFORMATION k Service Bulletins and Service Letters contain service information critical to the airworthiness and operation of particular magneto models. Consult the most current revision of Slick Master Service Manual F- 1100 for applicability of special service information to particular mag- neto models. Ml, OVERHAUL These magnetos should be completely overhauled as required by the inspections noted above. Total time in service may not exceed the manufacturer's TBO for the engine on which the magneto is installed. When servicing magnetos use only the most current revision of Slick manufactured parts. Inmostcasesit may be easierand more economi- cal to replace a faulty magneto with a new current production factory assembled unit than to perform the overhaul in the field. IV. REPLACEMENT These magnetos should be replaced as necessary when indicated by the above inspections. ; 4 WARRANTY: Void if prescribed maintenance schedules are not followed. CHECK WITH SLICK TO BE SURE YOU HAVE THE MOST CUR- RENT REVISIONS OF SLICK MANUALS F-1100, L-1020, L-1037, -1363, AND PERTINENT SLICK SERVICE BULLETINS BEFORE PERFORMING MAINTENANCE OR OVERHAUL. ISSUED REVISED Slick Aircraft Products PAGENO. || REVISION we, [ one [va [wo [ony [year Unison Industries 530 Blackhawk Park Avenue eee 04 OF 04 c so Joe) O) Rockford, llinois, USA 61104 wags Ue DIVITIVITITTTTTVITTPPITTTITTPPPTTTTTTT