Modular multistage pumps

SIHImulti
Type MSL, MSM

Description
SIHImulti pumps are horizontal multistage centrifugal pumps
of ring-section design, which meet the technical
requirements of ISO 5199 / EN 25199.
The advanced modular design reduces the number of parts
whilst maximising interchangeability.
Optimal selection of impeller diameter and diffuser size for
each ensures that the pump closely match the required duty
conditions.

Applications Construction
Pumps of the SIHImulti range meet the specific requirements Different hydraulic impeller and diffuser sizes can be
of many applications, such as: installed in a standardised casing, thus enabling the pump to
• Waterworks, and water supply be designed exactly for the working point required. The first
stage of each pump size is equipped with an suction
• Boiler feed impeller.
• Pressure boosting Axial thrust is hydraulically balanced by a patented balance
• Irrigation drum system with a self-adjusting throttling device. Residual
• High pressure cleaning thrust is absorbed by a generously-sized angular-contact
ball bearing. The balancing line is returned to the suction
• Heating casing or in the upstream vessel. Standard suction casing
• Condensate systems construction is with axial or radial inlet nozzles.
• Reverse osmosis A mechanical shaft seal is located on the drive side only. It
can consist of a packed gland (cooled or uncooled, with
• Chemical and Process
external flushing connection), (cooled or uncooled) single-
• and many more ... acting mechanical seal or (uncooled) double-acting
mechanical seal.
The pump rotor is supported on the drive side by grease-
lubricated anti-friction bearings and on the suction side by a
self-adjusting sleeve bearing lubricated by the pumped
liquid.
The pump is normally driven from the discharge side. As
option the pump can be driven from the suction side in which
case an antifriction inboard/outboard bearing is provided.
The casing components are sealed by O-rings. The pump
Technical Data casings are held together by external tie rods. The pump
feet are mounted to the suction and discharge casings in
Flowrate max. 450 m³/h such a manner that the suction casing (for suction casings
Head max. 630 m with radial branch) and discharge casing can be swung to
Speed max. 3600 rpm suit the installation conditions.
Temperature -10 to +180°C * All pump sizes can be provided with one or more dummy
Pressure Rating max. 63 bar stages, if required.
Shaft seal - packed gland
- mechanical seal
Direction of rotation counter-clockwise, when Options
viewed from discharge side
• Special materials
* 200°C as special design for example pump feet are
• Monitoring Systems
mounted concentric in accordance to ISO 9905

multi
133.23301.57.01 E PUMP TECHNOLOGY SIHI MSL, MSM
02/2008
SIHImulti

MSM

MSL

Suction Impeller
First stage impeller ensures reliable
operation with low NPSH conditions.

Suction Position Discharge Position

Adaptable design allows for either radial or Adaptable design allows different
axial suction. radial positions to be selected.

Product Lubricated Sleeve Bearing Modular Design

Self-aligning bearing for higher reliability Modular geometry of impellers/diffusers permits
optimal hydraulic design matching all duty
conditions.

2
 SIHImulti

New Design of Balance Drum System

This new, patented design combines a balance drum with a
self-adjusting throttling device. The benefits include:
• greatly reduced re-circulation flow in the balance line
• same balance drum system for different number of stages
• high efficiency, lower power consumption
• lesser wear rate as this system does not rely on tight,
wear-sensitive clearances to control the re-circulation flow

more ... for less ...

Shaft Sealing
• uncooled and cooled single-acting mechanical seal
• uncooled double acting mechanical seal
• Reduced life-cycle cost
- Enhanced efficiency with the balance drum system
• uncooled or cooled packed gland
- Only one shaft seal
- Lower power consumption
- High reliability
• Ease of maintenance
- Simple dismantling and assembly
• Minimised wear
- Reduced usage of spare parts
• Global service network
- Established local Service Centres around the world

3
SIHImulti
Range Coverage 50 Hz
n = 1450 rpm

MSM

MSL

n = 2950 rpm

MSM

MSL

4
 SIHImulti
Range Coverage 60 Hz
n = 1750 rpm

MSM

MSL

n = 3550 rpm

MSM

MSL

5
SIHImulti
Nozzle Position (viewed from drive end)
Discharge Casing

radial horizontal left radial top radial horizontal right

every combination of suction and discharge casing is possible

Suction casing

axial radial horizontal left radial top radial horizontal right

Flange Dimensions
ISO/EN/DIN
Pump Size Nominal Size DN (mm) Flange Shape/Nominal Pressure PN
Casing Material
suction side discharge Cast Iron, Ductile Iron Chrome Steel, Stainless Steel
axial radial side suction side discharge side suction side discharge side
032 80 50 32
050 100 80 50 DIN EN 1092 -2,
DIN EN 1092 - 2, PN 16, PN 25, DIN 2545,
065 125 100 65 DIN EN 1092 - 2, PN 40 DIN 2543, PN 40
PN 16, PN 25 DIN 2546, PN 16 DIN 2546,
100 150 125 100 PN 63 DIN 2544 PN 63
PN 25
125 200 150 125
150 200 200 150

ANSI
Pump size Nominal Size DN (inch) Flange Shape/Nominal Pressure PN
Casing Material
suction side discharge Cast Iron, Ductile Iron Chrome Steel, Stainless Steel
axial radial side suction side discharge side suction side discharge side
032 3“ 2“ 1 ¼“
050 4“ 3“ 2“
065 5“ 4“ 2 ½“ ANSI B 16.1, ANSI B 16.1, ANSI B 16.5, ANSI B 16.5,
250 FF 250 RF 300 RF 300 RF, 600 RF
100 6“ 5“ 4“
125 8“ 6“ 5“
150 8“ 8“ 6“

6
 SIHImulti
Shaft Sealing

Mechanical seal arrangement

uncooled, balanced cooled, balanced uncooled, unbalanced

GNZ seal
uncooled, balanced STERLING uncooled, double „back-to-back“

Packed gland arrangement

uncooled with jacket-cooling

with external flushing

7
SIHImulti
Sectional Drawing MSL, MSM with axial Inlet
Size 032 and 050

Size 065 and 100

8
 SIHImulti
Sectional Drawing MSL, MSM with axial Inlet
Size 125

Size 150

9
SIHImulti
Sectional Drawing MSL, MSM with radial Inlet
Size 032 and 050

Size 065 and 100

10
 SIHImulti
Sectional Drawing MSL, MSM with radial Inlet
Size 125

Size 150

11
SIHImulti
Sectional Drawing MSL, MSM with radial Inlet (drive on suction side)
Size 032 and 050

Size 065 and 100

12
 SIHImulti
Sectional Drawing MSL, MSM with radial Inlet (drive on suction side)
Size 125

Size 150

13
SIHImulti
Material Design
Type MSL
Pos. Item Material of Construction
OR OS OV OU 1R SC 4R
106 Suction Casing GG-25 GGG-40

EN-GJL 250 EN-JS 1030 1.4408

107 Discharge Casing GG-25 GGG-40

EN-GJL 250 EN-JS 1030 1.4408

108 Stage Casing GG-25 GGG-40

EN-GJL 250 EN-JS 1030 1.4408

230 Impeller GG-25 Bronze GG-25

EN-GJL-HB 195 2.1050 EN-GJL-HB 195 1.4408

231 Suction Impeller GG-25 GG-25

EN-GJL-HB 195 1.4409 EN-GJL-HB 195 1.4408 1.4408

171 Diffuser GG-25 Bronze GG-25

EN-GJL-HB 195 2.1050 EN-GJL-HB 195 1.4408

210 Shaft
1.4021 1.4462

524 Shaft Protection

Sleeve 1.4122 1.4460

523 Shaft Sleeve

1.4571

603.1 Balance Drum

603.2 System 1.4122 1.4460

542.1 Throttle Bush 1.4021 1.4462

542.2 Throttle Bush 1.4088

433 Mechanical Seal various Material Options

461 Packed Gland various Material Options

Type MSM
Pos. Item Material of Construction
0X SA 1S 1V 1R TA TB TD TE TF
106 Suction Casing GG-25 GGG-40 GG-25
EN-GJL 250 EN-JS 1030 EN-GJL 250 1.4008

107 Discharge Casing GGG-40

EN-JS 1030 1.4008

108 Stage Casing GGG-40

EN-JS 1030 1.4008

230 Impeller GG-25 Bronze GG-25

EN-GJL-HB 195 2.1050 EN-GJL-HB 195 1.4409

231 Suction Impeller GG-25 GG-25 GG-25

EN-GJL-HB 1.4408 EN-GJL-HB 195 1.4408 EN-GJL-HB 1.4408
195 195

171 Diffuser GG-25 Bronze GG-25

EN-GJL-HB 195 2.1050 EN-GJL-HB 195 1.4408

210 Shaft
1.4021

524 Shaft Protection

Sleeve 1.4122

523 Shaft Sleeve

1.4571

603.1 Balance Drum

603.2 System 1.4122

542.1 Throttle Bush 1.4021

542.2 Throttle Bush 1.4088

433 Mechanical Seal various Material Options

461 Packed Gland various Material Options

14
 SIHImulti
Operating Limits
Allowable Casing Pressure, Test Pressure
Type MSL
max. allowable Pressure (bar) Test
as a function of Liquid Temperature 1) Pressure
Size material of construction (bar)
Cast Iron Ductile Iron Stainless Steel
-10°C up to < 140°C < 180 °C - 40°C up to < 180°C < 20°C up to < 140 °C < 180°C
120 °C 120°C 100°C
S D S D S D S D S D S D S D S D S D
032
up to 16 40 15 38 14 34 16 40 15 37 13 32 12 30 11 28 21 52
150
Type MSM
max. allowable Pressure (bar) Test
as a function of Liquid Temperature 1) Pressure
Size material of construction (bar)
Cast Iron Ductile Iron Stainless Steel
-10°C up to < 140°C < 180 °C - 10°C up to < 140°C < 180°C -40°C up to < 140°C < 180°C
120 °C 120°C 120 °C
S D S D S D S D S D S D S D S D S D S D
032
up to 16 63 15 58 14 56 16 63 15 62,5 14 60 16 63 15,7 62,5 15,5 60 21 82
150
1)
consider mechanical seal pressure/temperature S = suction casing, D = discharge casing

Max. Speed and Number of Stages

Type MSL Type MSM
Size Hydraulic max. Speed max. Number of Size Hydraulic max. Speed max. Number
rpm Stages rpm of Stages
1450/1750 15 1450/1750 18
A 2950 13 A 2950 18
032 3550 9 032 3550 13
1450/1750 14 1450/1750 18
B 2950 12 B 2950 18
3550 8 3550 13
1450/1750 15 1450/1750 16
050 A, B 2950 8 050 A, B 2950 13
3550 6 3550 9
1450/1750 12 1450/1750 13
A, C 2950 5 A, C 2950 8
065 3550 3 065 3550 5
1450/1750 13 1450/1750 16
B, D 2950 6 B, D 2950 10
3550 4 3550 7
1450/1750 10 1450/1750 16
A, C 2950 3 A, C 2950 5
100 3550 2 100 3550 3
1450/1750 12 1450/1750 16
B, D 2950 4 B, D 2950 6
3550 3 3550 4
1450 11 1450 12
1750 8 1750 12
125 A, C 2950 3 125 A, C 2950 4
3550 2 3550 3
1450 12 1450 12
1750 10 1750 12
B, D 2950 3 B, D 2950 5
3550 2 3550 4
1450 7 1450 10
150 A, C 1750 5 150 A, C 1750 8
1450 9 1450 10
B, D 1750 6
B, D 1750 9

15
SIHImulti
Dimensional Drawing MSL with axial Inlet

Dimensions in mm, casing tolerance per DIN 1686/GTB 17 to be applied on dimensions of unmachined parts
Size Pump dimensions Feet dimensions Shaft end
DN2 DN1 f TS TD h1 h2 b s m2 m3 n1 n2 d2 l6 d11) l1 t u
032 032 080 410 24 165 175 70 20 30 45 335 300 14 380 28 60 31 8
050 050 100 415 36 185 200 70 20 30 45 335 300 14 385 28 60 31 8
065 065 125 510 38 39 230 250 88 25 35 60 380 320 19 490 40 110 43 12
100 100 150 520 37 33 285 320 88 25 35 60 380 320 19 485 40 110 43 12
125 125 150 649 51,5 320 365 97 30 40 75 410 350 24 609 70 166 74,5 20
150 150 200 660 39 365 450 115 30 70 110 490 410 30 660 55 167 59 16

Size 032 050 065 100 125 150

Stages a m4 a m4 a1 m4 a1 m4 a m4 a m4
2 150 120 175 135 260 180 305 225 380 340 380 270
3 195 165 230 190 330 250 390 310 490 450 505 395
4 240 210 285 245 400 320 475 395 600 560 630 520
5 285 255 340 300 470 390 560 480 710 670 755 645
6 330 300 395 355 540 460 645 565 820 780 880 770
7 375 345 450 410 610 530 730 650 930 890 1005 895
8 420 390 505 465 680 600 815 735 1040 1000 1130 1020
9 465 435 560 520 750 670 900 820 1150 1110 1255 1145
10 510 480 615 575 820 740 985 905 1260 1220
11 555 525 670 630 890 810 1070 990 1370 1330
12 600 570 725 685 960 880 1155 1075 1480 1440
13 645 615 780 740 1030 950 1240 1160
14 690 660 835 795
15 735 705 890 850
1)
k6 - tolerance fit

16
 SIHImulti
Dimensional Drawing MSL mit radial Inlet

Dimensions in mm, casing tolerance per DIN 1686/GTB 17 to be applied on dimensions of unmachined parts
Size Pump dimensions Feet dimensions Shaft end
DN2 DN1 f TS TD h1 h2 b s m2 m3 n1 n2 d2 l6 d11) l1 t u
032 032 050 410 23 24 165 175 70 20 30 45 335 300 14 380 28 60 31 8
050 050 080 415 32 36 185 200 70 20 30 45 335 300 14 385 28 60 31 8
065 065 100 510 36 39 230 250 88 25 35 60 380 320 19 490 40 110 43 12
100 100 125 520 35 33 285 320 88 25 35 60 380 320 19 485 40 110 43 12
125 125 150 649 36,5 51,5 320 365 97 30 40 75 410 350 24 609 70 166 74,5 20
150 150 200 660 41 39 365 450 115 30 70 110 490 410 30 660 55 167 59 16

Size 032 050 065 100 125 150

Stages e m4 e m4 e m4 e m4 e m4 e m4
2)
2 115 120 155 135 215 180 265 225 295 375 325 325
3 160 165 210 190 285 250 350 310 405 485 450 450
4 205 210 265 245 355 320 435 395 515 595 575 575
5 250 255 320 300 425 390 520 480 625 705 700 700
6 295 300 375 355 495 460 605 565 735 815 825 825
7 340 345 430 410 565 530 690 650 845 925 950 950
8 385 390 485 465 635 600 775 735 955 1035 1075 1075
9 430 435 540 520 705 670 860 820 1065 1145 1200 1200
10 475 480 595 575 775 740 945 905 1175 1255
11 520 525 650 630 845 810 1030 990 1285 1365
12 565 570 705 685 915 880 1115 1075 1395 1475
13 610 615 760 740 985 950
14 655 660 815 795
15 700 705 870 850
1)
k6 - tolerance fit
2)
Suction casing radial top only possible with 3 or more stages.

17
SIHImulti
Dimensional Drawing MSM with axial Inlet

Dimensions in mm, casing tolerance per DIN 1686/GTB 17 to be applied on dimensions of unmachined parts
Size Pump dimensions Feet dimensions Shaft end
DN2 DN1 f TS TD h1 h2 b s m2 m3 n1 n2 d2 l6 d11) l1 t u
032 032 080 410 24 165 175 70 20 30 45 335 300 14 380 28 60 31 8
050 050 100 415 36 185 200 70 20 30 45 335 300 14 385 28 60 31 8
065 065 125 510 38 39 230 250 88 25 35 60 380 320 19 490 40 110 43 12
100 100 150 520 37 33 285 320 88 25 35 60 380 320 19 485 40 110 43 12
125 125 150 649 51,5 320 365 97 30 40 75 410 350 24 609 70 166 74,5 20
150 150 200 660 39 365 450 115 30 70 110 490 410 30 660 55 167 59 16

Size 032 050 065 100 125 150

Stages a m4 a m4 a1 m4 a1 m4 a m4 a m4
2 150 120 175 135 260 180 305 225 380 340 380 270
3 195 165 230 190 330 250 390 310 490 450 505 395
4 240 210 285 245 400 320 475 395 600 560 630 520
5 285 255 340 300 470 390 560 480 710 670 755 645
6 330 300 395 355 540 460 645 565 820 780 880 770
7 375 345 450 410 610 530 730 650 930 890 1005 895
8 420 390 505 465 680 600 815 735 1040 1000 1130 1020
9 465 435 560 520 750 670 900 820 1150 1110 1255 1145
10 510 480 615 575 820 740 985 905 1260 1220 1380 1270
11 555 525 670 630 890 810 1070 990 1370 1330
12 600 570 725 685 960 880 1155 1075 1480 1440
13 645 615 780 740 1030 950 1240 1160
14 690 660 835 795 1100 1020 1325 1245
15 735 705 890 850 1170 1090 1410 1330
16 780 750 945 905 1240 1160 1495 1415
17 825 795
18 870 840
1)
k6 - tolerance fit

18
 SIHImulti
Dimensional Drawing MSM with radial Inlet

Dimensions in mm, casing tolerance per DIN 1686/GTB 17 to be applied on dimensions of unmachined parts
Size Pump dimensions Feet dimensions Shaft end
1)
DN2 DN1 f TS TD h1 h2 b s m2 m3 n1 n2 d2 l6 d1 l1 t u
032 032 050 410 23 24 165 175 70 20 30 45 335 300 14 380 28 60 31 8
050 050 080 415 32 36 185 200 70 20 30 45 335 300 14 385 28 60 31 8
065 065 100 510 36 39 230 250 88 25 35 60 380 320 19 490 40 110 43 12
100 100 125 520 35 33 285 320 88 25 35 60 380 320 19 485 40 110 43 12
125 125 200 649 36,5 51,5 320 365 97 30 40 75 410 350 24 609 70 166 74,5 20
150 150 200 660 41 39 365 450 115 30 70 110 490 410 30 660 55 167 59 16

Size 032 050 065 100 125 150

Stages e m4 e m4 e m4 e m4 e m4 e m4
2)
2 115 120 155 135 215 180 265 225 295 375 325 325
3 160 165 210 190 285 250 350 310 405 485 450 450
4 205 210 265 245 355 320 435 395 515 595 575 575
5 250 255 320 300 425 390 520 480 625 705 700 700
6 295 300 375 355 495 460 605 565 735 815 825 825
7 340 345 430 410 565 530 690 650 845 925 950 950
8 385 390 485 465 635 600 775 735 955 1035 1075 1075
9 430 435 540 520 705 670 860 820 1065 1145 1200 1200
10 475 480 595 575 775 740 945 905 1175 1255 1325 1325
11 520 525 650 630 845 810 1030 990 1285 1365 1450 1450
12 565 570 705 685 915 880 1115 1075 1395 1475 1575 1575
13 610 615 760 740 985 950 1200 1160
14 655 660 815 795 1055 1020 1285 1245
15 700 705 870 850 1125 1090 1370 1330
16 745 750 925 905 1195 1160 1455 1415
17 790 795
18 835 840
1)
k6 - tolerance fit
2)
Suction casing radial top only possible with 3 and more stages.
19
SIHImulti
Dimensional Drawing MSL and MSM with radial Inlet (drive on suction side)

Dimensions in mm, casing tolerance per DIN 1686/GTB 17 to be applied on dimensions of unmachined parts
Size Pump dimensions Feet dimensions Shaft end
1)
DN2 DN1 f f1 TS TD h1 h2 b s m2 m3 n1 n2 d2 l4 d1 l1 t u
032 032 050 350 390 23 24 165 175 70 20 30 45 335 300 14 415 28 60 31 8
050 050 080 355 410 32 36 185 200 70 20 30 45 335 300 14 460 28 60 31 8
065 065 100 397 504 36 39 230 250 88 25 35 60 380 320 19 559 40 110 43 12
100 100 125 410 501 35 33 365 450 88 25 35 110 380 320 19 471 40 113 43 12
1253) 125 150 483 644 36,5 51,5 320 365 97 30 40 75 410 350 24 604 70 166 74,5 20
1503) 150 200 493 655 41 39 365 450 115 30 40 110 490 410 30 655 55 167 59 16

Size 032 050 065 100 125 150

Stages e m4 e m4 e m4 e m4 e m4 e m4
22) 115 120 155 135 215 180 265 330 295 375 325 325
3 160 165 210 190 285 250 350 415 405 485 450 450
4 205 210 265 245 355 320 435 500 515 595 575 575
5 250 255 320 300 425 390 520 585 625 705 700 700
6 295 300 375 355 495 460 605 670 735 815 825 825
7 340 345 430 410 565 530 690 755 845 925 950 950
8 385 390 485 465 635 600 775 840 955 1035 1075 1075
9 430 435 540 520 705 670 860 925 1065 1145 1200 1200
10 475 480 595 575 775 740 945 1010 1175 1255 1325 1325
11 520 525 650 630 845 810 1030 1095 1285 1365
12 565 570 705 685 915 880 1115 1180 1395 1475
13 610 615 760 740 985 950 1200 1265
14 655 660 815 795 1055 1020 1285 1350
15 700 705 870 850 1125 1090 1370 1435
16 745 750 925 905 1195 1160 1455 1520
17 790 795
18 835 840
1)
k6 - tolerance fit
2)
Suction casing radial top only possible with 3 and more stages.
3)
with oel lubrication

20
 SIHImulti
Connections
MSL with axial Inlet (Size 032 up to 100)

Pos. Connection Size

Dimension
032 065
050 100
1)
I Pressure gauge G1/2 G1/2

1)
II Pressure gauge G1/2 G1/2

1)
III Vent G1/4 G1/4

1)
VII Drain G1/4 G1/2

1)
IX Drain G3/8 G3/4
MSL with radial Inlet (Size 032 up to 100)
Xa Flushing connection G1/4 G1/4

XIa Cooling inlet seal chamber G3/8 G1/2

XIb Cooling outlet seal chamber G3/8 G1/2

XII Connection for circulation G1/4 G1/4

XX Grease luibrication M6 M6
XXX Thrust impulse measuring
possible
1)
tapped and plugged

MSM with axial Inlet (Size 032 up to 100)

Pos. Connection Size

Dimension
032 065
050 100
1)
I Pressure Gauge G1/2 G1/2

1)
II Pressure Gauge G1/2 G1/2

1)
III Vent G1/4 G1/4

1)
VII Drain G1/4 G1/2

1)
IX Drain G3/8 G3/4
MSM with radial Inlet (Size 032 up to 100)
XIa Cooling Inlet - seal chamber G3/8 G1/2

XIb Cooling Outlet - seal chamber G3/8 G1/2

XII Connection for Circulation G1/4 G1/4

XX Grease Luibrication M6 M6

Thrust Impulse Measuring

XXX
possible
1)
tapped and plugged

21
SIHImulti
Connections
MSL/MSM with axial Inlet (Size 125 and 150)

Pos. Connection Size

Dimension
125 150

1)
I Pressure gauge G1/2 G1/2

1)
IIa Pressure gauge G1/2 G1/2

IIIa Vent mechanical seal G1/2 G1/2

IIIb Vent bearing G1/2 G1/2

1)
MSL/MSM with radial Inlet (Size 125 and 150) VII Drain G3/4 G3/4

1)
IX Leck outlet G1/2 G1/2

Cooling inlet seal

XIa G1/2 G1/2
chamber
Cooling outlet seal
XIb G1/2 G1/2
chamber
Pipe Pipe
XIc Cooling inlet bearing
ø 12 ø 12
Pipe Pipe
XId Cooling outlet bearing
ø 12 ø 12
Connection for
XII G1/4 G1/4
circulation
1)
XVI Oil outlet G3/8 G3/8

MSL/MSM with drive end on suction side (Size 125 and 150) XVIIa Oil level sight glas G1/2 G1/2

XVIIb Constant level oiler G1/4 G1/4

Connection for balancing

XXII G3/4 G3/4
flow
1) Connection for
XXIV G1/2 G1/2
thermometer
1)
tapped and plugged

22
 SIHImulti
Material Description
Manufacturing standard equivalent or comparable standard
Material-No. DIN-material code EN-designation US-material code ISO Japan components
old new ASTM-Standards UNS JIS
EN-JL 1040 GG-25 EN-GJL 250 EN-GJL 250 A 278 Class 30 F 12401 185/Gr. 250 G 5501, FC 300 Casing
EN-JL 2030 GG-25 EN-GJL-HB 195 EN-GJL-HB 195 A 48 Class 25/30 F 11701/F 12101 185/Gr. 300 G 5501, FC 250/300 Impeller/Diffuser
EN-JS 1030 GGG-40 EN-GJS-400-15 EN-GJS-400-15 A 536 Gr. 60-40-18 Casing
2.1050 G-CuSn 10 B 427 C91600 C 91600 Impeller/Diffuser
1.4008 G-X8CrNi 13 G-X7CrNiMo 12-1 G-X7CrNiMo 12-1 A 217 Gr. CA 15 J 91 150 G 5121, C1 SCS 1 Casing
1.4088 G-X170Cr18 G-X170Cr18 Throttle Bush
1.4021 X20Cr 13 X20Cr 13 X20Cr 13 A 276 Type 420 S 42 000 683-13-4 G 4303,Grl SUS 403 Shaft, Throttle Bush
1.4122 X35CrMo 17 X39CrMo 17-1 X39CrMo 17-1 Balance Drum,
Shaft Sleeve
1.4408 G-X6CrNiMo 18 10 G-X5CrNiMo 19-11-2 G-X5CrNiMo A 351, 743, 744 CF 8M J 92 800 683-13-9 SCS 14 Impeller/Diffuser,
19-121-2 Casing
1.4460 X4CrNiMo 27 5 2 X3CrNiMoN 27-5-2 X3CrNiMoN 27-5-2 Balance Drum
1.4462 X2CrNiMoN 22 5 3 X2CrNiMoN 22-5-3 X2CrNiMoN 22-5-3 A 276-S 31803 S 31 803 G 4303, Grl SUS 329 Shaft, Throttle Bush
1.4571 X6CrNiMoTi 17 12 2 X6CrNiMoTi 17-12-2 X6CrNiMoTi 17-12-2 193 Gr. B 8 M S 31 600 683-1-21 G 4303, Grl SUS 316 Shaft Sleeve

Materials are produced to EN/DIN specifications. For other equivalent or comparable standards are mentioned only for information.

ASTM American Society for Testing and Materials

DIN Deutsches Institut für Normung e.V.
EN European Standard
ISO International Standardisation Organisation
UNS Unified Numbering System (USA)

23
SIHImulti

Sterling SIHI GmbH

Werk Ludwigshafen
Halbergstr. 1, D-67061 Ludwigshafen, Germany
Telefon +49 (0)621 56 12 - 0 Telefax +49 (0)621 56 12 - 209

24