Volkswagen Phaeton - Steering Стр.
1 из 16
94 - 8
Steering column switch
Note:
The control module for the steering column
electronics has on board diagnostics.
Familiarity with the function and operation of the
steering column switch is essential in the event of
customer complaints.
Additional information Owners manual
DTC recognition and display
The control module for steering column electronics is
equipped with on-board diagnostics, which simplifies
faultfinding.
Performing on-board diagnostics: Use the "Guided Fault
Finding" function of the Diagnostic Operation System VAS
5051 .
Steering column switch, assembly overview
Steering column switch Стр. 2 из 16
Note:
The following parts of the steering column switch
cannot be disassembled:
Steering column switch cover, left Item - 3 -
Left Steering Wheel Tiptronic Switch E389 Item -
4-
Bracket Item - 5 -
Bracket Item - 7 -
Multiconnector for Steering Wheel Tiptronic Switch
E389 Item - 8 -
Steering column switch Стр. 3 из 16
Bracket Item - 9 -
Right Steering Wheel Tiptronic Switch E389 Item
-4-
Steering column switch cover, right Item - 11 -
1 - Steering Column Electronic
Systems Control Module J527
Removing and installing, 94-8,
Steering column switch, assembly
and disassembly .
Steering Column Electronic
Systems Control Module J527 ,
coding 94-8, Steering Column
Electronic Systems Control Module
J527 , coding .
Steering column switch Стр. 4 из 16
Steering column switch pin
assignment, 94-8, Steering
column switch pin assignment
2 - Steering column
3 - Steering column switch cover, left
at Left Steering Wheel Tiptronic
Switch E389
4 - Steering Wheel Tiptronic Switch
E389
Removing and installing, 94-8,
Steering column switch, assembly
and disassembly .
Steering column switch pin
assignment, 94-8, Steering
column switch pin assignment
5 - Holder
at Left Steering Wheel Tiptronic
Switch E389
6 - Torx screw
For attaching Steering Wheel
Tiptronic Switch E389 , left and
right.
7 - Holder
For Tiptronic switch multi-
connector and multi-connector for
spiral springs
8 - Multiconnector for Steering Wheel
Tiptronic Switch E389
Pin assignment 94-8, Steering
column switch pin assignment
9 - Holder
at Right Steering Wheel Tiptronic
Switch E389
10 - Steering Wheel Tiptronic Switch
E389
Removing and installing, 94-8,
Steering column switch, assembly
Steering column switch Стр. 5 из 16
and disassembly .
Steering column switch pin
assignment, 94-8, Steering
column switch pin assignment
11 - Steering column switch cover,
right
12 - Torx screw
For attaching Steering Wheel
Tiptronic Switch E389 , left and
right.
13 - Windshield Wiper/Washer Switch
E22
Removing and installing, 94-8,
Steering column switch, assembly
and disassembly .
Steering column switch pin
assignment, 94-8, Steering
column switch pin assignment
14 - Airbag Spiral Spring/Return
Spring With Slip Ring F138 and
Steering Angle Sensor G85
Removing and installing, 94-8,
Steering column switch, assembly
and disassembly .
15 - Allen bolt
1.5 Nm
For attaching steering column
switch
16 - Turn Signal Switch E2
Removing and installing, 94-8,
Steering column switch, assembly
and disassembly .
Steering column switch pin
assignment, 94-8, Steering
column switch pin assignment
Steering column switch, removing and installing
Note:
Steering column switch Стр. 6 из 16
Always observe work procedure and Notes for
disconnecting and reconnecting batteries 27-3,
Battery, disconnecting and connecting .
Special tools, testers and auxiliary items required
Release lever T10039 L
Steering column switch, removing
- Using either the electric or mechanical position adjuster,
move the steering wheel completely outward and down.
- Remove terminal clamps from the battery 27-3,
Battery, disconnecting and connecting .
- Remove drivers airbag.
Repair Manual, Body Interior, Repair Group 69, Airbag;
Driver airbag unit, removing and installing
- Remove steering wheel.
Repair Manual, Body Interior, Repair Group 69, Airbag;
Driver airbag unit, removing and installing
Steering column switch Стр. 7 из 16
- Remove the bolts - arrows - .
- Lift the cover - arrow - , right, from the steering column
switch using the wedge T10039/1 and push it outward.
- The left cover is the mirror image of the right and is pried
off the steering wheel column switch using the wedge
T10039/1 and pushed outward.
Note:
Do not disassemble the covers.
- Move the upper cover - upper arrow - upward from the
steering column switch and pull it out.
Steering column switch Стр. 8 из 16
- Move the lower cover - lower arrow - downward from
the steering column switch and pull it out.
- Remove Allen bolt - arrow - .
- Remove the steering column switch.
- Pull off the retaining clip of the wiring harness - arrow -
.
- Pull plug connectors - arrows - from the steering column
switch.
Installing:
Install in reverse order of removal, noting the following:
Steering column switch Стр. 9 из 16
- Tighten the Allen bolt - arrow - using 1.5 Nm torque.
- Insert the lower steering column switch cover as shown -
arrows - .
- Install steering wheel
Repair Manual, Body Interior, Repair Group 69, Airbag;
Steering wheel, removing and installing
- Install drivers airbag.
Repair Manual, Body Interior, Repair Group 69, Airbag;
Driver airbag unit, removing and installing
Steering column switch, assembly and disassembly
Disassembly
- Remove steering column switch 94-8, Steering column
switch, removing and installing .
Steering column switch Стр. 10 из 16
- Remove both bolts - arrows - on the Tiptronic switch
bridge
- Remove both bolts - arrows - on the Tiptronic switches.
- Loosen the retainer - arrow - on the spiral spring multi-
connector - 1 - .
- Carefully set aside the holder - 2 - with the multi-
connector for Tiptronic - - 3 - .
Steering column switch Стр. 11 из 16
- Loosen the retainer - arrows - on the right Tiptronic
switch bridge.
- Set the bridge with the right Tiptronic switch carefully
aside.
- Loosen the retainer - arrows - on the left Tiptronic
switch bridge and remove the entire Tiptronic switch.
- Carefully remove the airbag spiral spring with the
Steering Angle Sensor G85 from the steering column
switch.
- To remove the windshield wiper switch, remove the bolts
- 2- .
- Remove wiper switch.
Steering column switch Стр. 12 из 16
- To remove the turn signal switch, remove the bolts - 1 -
.
- Remove turn signal switch.
- Remove Steering Column Electronic Systems Control
Module J527 from turn signal switch.
Assembly:
Assemble in reverse order, noting the following:
Note:
If the Steering Column Electronic Systems Control
Module J527 is replaced, the unit must be coded
94-8, Steering Column Electronic Systems Control
Module J527 , coding .
Note the correct position of the leads within the
steering column switch.
Steering column switch pin assignment
I - Multi-connector I for Easy Entry function switch .
II - Multi-connector II for Tiptronic switch
III - Multi-connector III for spiral springs
IV - Multi-connector IV for voltage supply, CAN and
Terminal 15
Steering column switch Стр. 13 из 16
I - 4-pin connector
1 - On/off for Easy Entry
2 - Direction
3 - Terminal 31, negative
4 - not in use
II - 5-pin connector
1 - Terminal 31, negative
2 - Up (upshift)
3 - Down (downshift)
4 - not in use
5 - not in use
Steering column switch Стр. 14 из 16
III - 4-pin connector
3 - Spiral spring connection
4 - Spiral spring connection
5 - Spiral spring connection
6 - Spiral spring connection
IV - 16-pin connector
1 - Terminal 31, negative
2 - Terminal 30, positive
3 - Drive CAN, screening
4 - not in use
5 - CCS switch setting Off
6 - not in use
7 - not in use
8 - Convenience CAN, Low
9 - Convenience CAN, High
10 - Drive system CAN High
11 - Drive system CAN Low
12 - not in use
Steering column switch Стр. 15 из 16
13 - Terminal 15
14 - not in use
15 - not in use
16 - not in use
Steering Column Electronic Systems Control Module
J527 , coding
DTC recognition and display
The control module for steering column electronics is
equipped with on-board diagnostics, which simplifies
faultfinding.
Performing on-board diagnostics: Use the "Guided Fault
Finding" function of the Diagnostic Operation System VAS
5051 .
Special tools, testers and auxiliary items required
Diagnostic Operation System VAS 5051
Diagnostic cable VAS 5051/6A
Diagnostic Operation System VAS 5051 , attaching
- Apply parking brake.
- Place gear selector lever in "P" or "N" .
Steering column switch Стр. 16 из 16
- Connect the Vehicle Diagnostic Testing and Information
System Diagnostic Operation System VAS 5051 with the
ignition switched off.
- Switch ignition on.
- Turn off all electrical consumers.
Note:
If 5051 display is blank Operating instructions for
Diagnostic Operation System VAS 5051 .
- Select "Guided Fault-Finding" on the Diagnostic
Operation System VAS 5051 .
- Select "Go To" , "Functions/Component Selection" and
the following menu options in sequence:
Body (Repair Group 01; 27; 50 to 97)
Electrical System (Repair Group 01; 27; 90 to 97)
01 Systems capable of self-diagnosis
Steering wheel electronics
Steering wheel electronics functions
Coding control module steering wheel electronics
