Cat ®

631K
WHEEL TRACTOR-SCRAPER

MAIN FEATURES AND BENEFITS:

„ Tractor Serviceability Improvement – The fuel, water and engine oil „ Ground Speed Control – Ground Speed Control sets the desired top
are relocated at ground level on the right hand side of the machine speed by the operator if job site conditions or segment speed limits
for easy access. require a speed less than full run out. Machine Speed Limit is intended
„ Brakes – Have been changed from an air actuated drum shoe brake to for use when top speed needs to be limited for longer durations and
a hydraulic actuated tractor wet disc brake and a scraper dry caliper. Ground Speed Control is intended for use when the top speed needs
„ Tire Spin Reduction – This feature will allow the machine to control to be reduced for shorter segments or intermediate periods of time.
the slip of the tractor tires only. The operator can set the desired top speed and the machine will find
the correct gear that works best for the engine and transmission.
„ Engine Over Speed Protection – In the event of an engine over speed
situation, the compression brake or brakes will automatically engage „ Sequence Assist (Optional Attachment) – This option uses cylinder
with no operator input. The machine determines the over speed position sensors to automate bowl, apron and further implement
condition based on rate of acceleration and applies compression controls throughout the four core work cycles: Dig, Haul, Unload
brakes automatically. and Return. When utilized this can reduce up to 14 individual operator
commands per cycle. Sequence Assist simplifies control over the
„ Advanced Cushion Hitch – With similar technology as the Cat® Advanced implements, reduces joystick usage, automatically controls cushion
Ride Management seat suspension, this software allows the cushion hitch, transmission hold and ejector.
hitch to prevent end stroke by having the ability to predict end stroke
events and manage the rate of dampening. Resulting in reduced hitch „ Payload Estimator (Optional Attachment) – The Payload Estimator will
maintenance and improved operator ride in rough conditions. calculate the payload of the machine in tonnes or tons by measuring
the bowl lift cylinder pressures at the beginning of the loaded haul
„ High Pressure Steering – K Series steering system design requires segment. This feature works best when using Sequence Assist.
significantly less steering effort. The reduced steering effort will allow Using Payload Estimator during testing has achieved better than
for decreased operator fatigue and a more efficient operator resulting 95% accuracy when compared to actual scale weights. The Payload
in possible higher rates of production late in the work cycle. Estimator feature comes automatically when a machine is ordered
„ Differential Lock Engagement Protection – This standard feature with Sequence Assist.
allows the machine to prevent the operator from engaging the „ Load Assist (Optional Attachment) – Is designed to help shorten the
differential lock when damage could occur. learning curve of inexperienced operators to ensure consistency
„ Cab Improved – The K Series cab interior improves operator comfort and faster loading of material while reducing effort of the operator.
and visibility. The overall interior is 21% larger than the G Series cab. Based on the speed of the machine, Load Assist automatically adjusts
„ Machine Speed Limit – This feature is designed to take the place the cutting edge height to manage wheel slip and to ensure consistent
of top gear selection. If the machine top speed needs to be limited and efficient loading in bulk earthmoving applications.
the operator can select the top speed through the display or the top „ Cat Grade Control (Optional Attachment) – Intelligently ensures the
speed can be set in ET. This will allow the machine to find the correct machine does not cut below grade in the cut area or over fill in the fill
gear that works best for the engine and transmission. Allowing the area – avoiding rework and moving unnecessary material.
engine and transmission to select the correct gear to pull the load in
most cases resulting in a lower engine load factor and lower fuel burn
verses using top gear selection that required the machine to run at
engine speeds at or close to high idle.
631K Wheel Tractor-Scraper

Specifications
General Data Safety Criteria Compliance Standards
Fuel Tank Refill Capacity: Scraper 874 L 231 U.S. gal Rollover Protection Structure (ROPS) ISO 3471:2008 for up to
Overall Width 3.94 m 12'11" 21 282 kg (46,919 lb)
Overall Shipping Height 3.89 m 12'9" Falling Object Protective Structure (FOPS) ISO 3449:2005 Level II
Scraper Capacity: Brakes ISO 3450:2011
Struck 18.3 m3 24 yd3 Steering System ISO 5010:2007
Heaped 26 m3 34 yd3 Seat Belt SAE J386:FEB2006
Rated Load 37 200 kg 82,200 lb Reverse Alarm ISO 9533:2010
37.2 tonnes 41.1 tons
Width of Cut 3.51 m 11'6" Travel Speeds (Runout)
Maximum Depth of Cut 450 mm 17.7" Transmission Gear:
Maximum Depth of Spread 535 mm 21.1" First 5.5 km/h 3.4 mph
Top Speed (Loaded) 55.8 km/h 34.7 mph Second 10.0 km/h 6.2 mph
180° Curb-to-Curb Turning Width 12.23 m 40'2" Third 12.4 km/h 7.7 mph
Tires: Fourth 16.9 km/h 10.5 mph
Tractor 37.25R35**E3 Fifth 22.7 km/h 14.1 mph
Scraper 37.25R35**E3 Sixth 30.6 km/h 19.0 mph
Seventh 41.4 km/h 25.7 mph
Non Push-Pull Eighth 55.8 km/h 34.7 mph
Operating Weight (Empty) 46 600 kg 102,750 lb Reverse 9.9 km/h 6.2 mph
Overall Length 15.04 m 49'4"
Implement Cycle Times
Push-Pull Bowl Raise 3.5 seconds
Operating Weight (Empty) 48 275 kg 106,430 lb Bowl Lower 3.5 seconds
Overall Length (With Bail Down) 16.64 m 54'7" Apron Raise 4.0 seconds
Apron Lower 3.8 seconds
Engine Ejector Extend 8.5 seconds
Engine Model: Tractor Cat C18 ACERT™ Ejector Retract 8.5 seconds
Rated Engine RPM: Tractor 1,900 rpm Bail Raise 1.5 seconds
Flywheel Power: Tractor 425 kW 570 hp Bail Lower 2.1 seconds
• Cat C18 ACERT engine meets U.S. EPA Tier 4 Final/EU Stage IV
emission standards. Service Refill Capacities
Crankcase (Tractor) 52 L 13.7 gal
Cab Transmission System 110 L 29 gal
• ROPS/FOPS meet “ISO Standards.” Cooling System 75 L 19.8 gal
• The exterior sound power level for the standard machine (ISO 6393) Fuel Tank 874 L 231 gal
is 111.5 dB(A). Hydraulic System 142 L 37.5 gal
Diesel Exhaust Fluid (DEF) 30.5 L 8 gal

2
 631K Wheel Tractor-Scraper

4 5 6 7
1 2 3 10

8 11

9 12 14
13

Dimensions
mm in mm in
1 Width – Overall Machine 3937 155 9 Front of Tractor to Front Axle 3612 142.2
2 Width – Tractor 3499 137.8 10 Axle to Vertical Hitch Pin 509 20
3 Width – Rear Tire Centers 2462 96.9 11 Height – Scraper Blade Maximum 510 20
4 Width – Inside of Bowl 3404 134 12 Wheelbase 8808 346.8
5 Width – Outside Rear Tires 3636 143.2 13 Length – Overall Machine (Standard) 15 164 597
6 Height – Overall Shipping 3892 153.2 Length – Maximum (Push-Pull) 16 640 655.1
7 Height – Top of Cab 3733 147 14 Rear Axle to Rear of Machine 2744 108
8 Ground Clearance – Tractor 664 26.1

STANDARD EQUIPMENT
POWER TRAIN – TRACTOR POWER TRAIN – SCRAPER OPERATOR ENVIRONMENT – TRACTOR
„ Cat C18 ACERT engine with MEUI™ „ Braking system: „ HVAC system, heat, AC, defrost
„ Compression engine brake • Primary and secondary, dry caliper, „ Thermostat control of HVAC system
„ Electric start, 24V hydraulic actuated „ Coat hook
„ Air cleaner, dry type with precleaner „ Lunchbox platform with holding strap
ELECTRICAL – TRACTOR
„ Fan, hydraulic „ Diagnostic connection (2)
„ Alternator, 150 Amp
„ Ground level engine shutdown „ 12V power ports (2)
„ Batteries (4), 12V, 1,000 CCA, maintenance
„ Radiator, aluminum unit core, 9 fins per inch „ Differential lock (1)
free, high output
„ Guard, crankcase „ Dome courtesy light
„ Electrical system, 24V
„ Starting aid, ether „ Horn, electric
„ Lighting system:
„ Braking system: „ T-Handle implement control
• Headlights, LED
• Primary and secondary, wet disc, hydraulic • Turn signals with hazard function, „ Mirror, rearview
• Parking, hydraulic-released, spring-applied LED floodlights, (2) cutting edge (1) bowl, „ Radio ready
• Throttle lock halogen side vision (2) „ ROPS/FOPS cab, pressurized
„ Transmission: „ Starting/charging receptacle „ Keypad switches:
• 8-speed planetary power shift • Throttle lock
• ECPC control ELECTRICAL – SCRAPER
• Wipers/washers
• APECS software „ Alarm, backup • Hazard lights
• Programmable top gear selection „ Lighting system:
• Retarding level select
• Transmission hold • Brake lights, LED • Work lights on, off
• Differential lock • Turn signals with hazard function, LED • Information mode on Messenger Display
• Guard, power train
(continued on next page)
• Standard tire spin reduction
• Ground speed control
• Machine speed limit
• Differential lock protection

3
631K Wheel Tractor-Scraper
STANDARD EQUIPMENT (continued)
OPERATOR ENVIRONMENT – TRACTOR „ Gauges, warnings include: FLUIDS
(continued) • Coolant temperature „ Extended Life Coolant to –37° C (–34° F)
„ Safety tab rocker switches • Engine oil temperature
„ Seat belt, static two-piece • Hydraulic oil temperature OTHER STANDARD EQUIPMENT – TRACTOR
„ Seat, Cat Advanced Ride Management (ARM), • Diesel Particulate Filter (DPF) temperature „ Advanced cushion hitch
Cat Comfort Series 3, rotates 30 degrees • Fuel level „ Accumulators (cushion hitch) with Canadian
„ Steering wheel, tilt, telescoping, padded Registration Number (CRN)
• Park brake
„ Windows, right side emergency egress „ Fast oil change
• Implement lockout
„ Windows, sliding „ Fenders, non-metallic
• Brake system
„ Windows, laminated, zipped in „ Heater, engine coolant 120V
• Regeneration required
„ Windshield wipers, front and rear windows, „ Rims (2)
• Throttle lock
includes washers • System voltage „ Tow hooks, front
„ Door lock • Secondary steering „ Vandalism locks
„ Messenger Display • Bail down „ Heater, engine coolant 120V

• Ejector auto „ Steering locks

• Differential lock
OTHER STANDARD EQUIPMENT – SCRAPER
• Apron float
„ Bowl:
• Transmission hold
• 18.3 m3 (24 yd3), struck
• Cushion hitch
• 26 m3 (34 yd3), heaped
• High beam lights
„ Vandalism locks
• Action lamp
„ Rims (2)
• Engine speed, rpm
„ Hydraulic position sensing cylinders
• Gear selection
(bowl lift and apron)
• DEF fill levels

OPTIONAL ATTACHMENTS
STEERING ARRANGEMENTS OTHER ATTACHMENTS SERVICE INSTRUCTIONS
„ Secondary Steering Arrangement „ Camera arrangement – Work Area Vision „ Film arrangement – U.S. (ANSI)
System (WAVS) „ Film arrangement – International (ISO)
INTEGRATED TECHNOLOGIES „ Cab beacon
„ Sequence Assist Arrangement with
„ Air horn
Payload Estimator
„ Air horn and beacon
„ Load Assist
„ Fender, scraper
„ Cat Grade Control with Load Assist
„ Guard, overflow
„ Advanced Tire Spin Reduction
„ Wiring group
„ Push Pull

For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com AEHQ7763 (01-2016)
© 2016 Caterpillar
All rights reserved
Materials and specifications are subject to change without notice. Featured machines in photos may include additional
equipment. See your Cat dealer for available options.
CAT, CATERPILLAR, SAFETY.CAT.COM, their respective logos, “Caterpillar Yellow” and the “Power Edge” trade dress, as well
as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.