See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/340134033

Natural Gas Sweetening Systems Selection, Sizing and Troubleshooting, Kolmetz

Handbook Of Process Equipment Design

Article · March 2012

CITATIONS READS

0 104

1 author:

Karl Kolmetz
Universiti Malaysia Pahang
129 PUBLICATIONS 54 CITATIONS

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

Process Safety View project

Distillation Optimization View project

All content following this page was uploaded by Karl Kolmetz on 25 March 2020.

The user has requested enhancement of the downloaded file.

 Page : 1 of 66

KLM Technology
Group Rev: 01

Practical Engineering Engineering Solutions

Guidelines for Processing
Plant Solutions
Rev 01 March 2012
www.klmtechgroup.com

Co Author:
KLM Technology Group Kolmetz Handbook
P. O. Box 281
Bandar Johor Bahru,
Of Process Equipment Design Rev 01 Aprilia Jaya
80000 Johor Bahru,
Johor, West Malaysia
Natural Gas Sweetening Systems Editor / Author :
Selection, Sizing and
Karl Kolmetz
Troubleshooting

(ENGINEERING DESIGN GUIDELINES)

TABLE OF CONTENT

INTRODUCTION 4

Scope 4

General Design Consideration 5

DEFINITION 17

NOMENCLATURE 22

THEORY OF THE DESIGN 24

Absorber Design 24

Regenerator Design 31

Rich Solution Hydrocarbon Flash/Skimming Drum Design 37

Rich/Lean Exchanger Design 40

 Page 2 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Reclaimer Design 44

Filter Design 48

Carbon Treater (Charcoal Filter) 49

Anti-foam Agent Injection Facilities Design 50

Corrosion Control 52

APPLICATION

Application 1: Calculated Heat Duty, Area, and Power Requirements for MEA 55

Application 2: Calculated Heat Duty, Area, and Power Requirements for DEA 57

Application 3: Calculated Acid Gas Absorbed, Rich/Lean Load, and Bulge Temperature 59

REFEREENCE 63

CALCULATION SPREADSHEET 64

Heat Duty, Area, and Power Requirements.xls 64

Acid Gas Absorbed, Rich/Lean Load, and Bulge Temperature.xls 65

LIST OF TABLE

Table 1: the relation number actual trays with H2S partial pressure 25

Table 2: Heats reaction 29

Table 3: Regenerator capacity 32

Table 4: Reflux Accumulator Capacities 34

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 3 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Table 5: Estimated heat exchange requirements 41

Table 6: Surge Tank Capacities 43

Table 7: Estimated Power Requirements for Pumps 54

LIST OF FIGURE

Figure 1: Reaction between acid gas and amine 9

Figure 2: Process flow scheme of gas sweetening 11

Figure 3: MEA Scrubber feed Separator drum 30

Figure 4: Kettle Reboiler 36

Figure 5: Rich solution skimming/flash drum 39

Figure 6: U-tube Heat Exchanger 42

Figure 7: Reclaimer 47

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 4 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

INTRODUCTION

Scope

This guideline provides how to design a gas sweetening system especially when utilizing
alkanolamines. This design guideline can assist engineers in understanding the basic
design of a gas sweetening system including suitable sizing of equipment, material
selection and suitable amine selection. This guideline also includes the engineering
calculations for sizing of the gas sweetening systems.

The choice of amine and equipment design is crucial to give the best performance of a
gas sweetening system. The performance of gas sweetening system is influenced by the
choice amine used to treat the acid gas and all the equipment used in the system, such
as absorber, regenerator, and reboiler. This guideline will assist in calculating the size,
heat duty, area, and power requirements of the various pieces of equipment. Additionally
acid gas absorbed, circulation and bulge temperature will be calculated.

The design of gas sweetening system may be influenced by factors, including process
requirements, economics and safety. There are tables that assist in making these
factored calculations from the various referenced sources. All the important parameters
use in the guideline are explained in the definition section which help the reader more
understand the meanings of the parameters or the terms utilized.

The theory section explains the correct selection of equipment which is used in gas
sweetening systems, how to calculate equipment sizing, and selection of the best amine
solution for each application. The application of the gas sweetening system theory with
the examples will assist the engineer to understand the concepts of gas sweetening and
then be prepared to perform the actual design of the gas sweetening.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 5 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

General Design Consideration

In some hydrocarbon processing plants acid gas such as Hydrogen sulfide (H2S) and
carbon dioxide (CO2) are present in the gas streams. They can also be organic sulfur in
the form of carbonyl sulfide (COS). The streams can be natural and associated gases
such as propane and butane, and products from upgrading of heavy oils, bitumen or coal.

Gas sweetening technology using alkanolamines to remove acid components from

hydrocarbon riches gasses have been in operation for many years. The alkanolamine
processes are particularly applicable where acid gas partial pressures are low or low
levels of acid gas are needed in the sweet gas. Alkanolamines are used because they
form basic solutions when mixed with water and chemically enhance the absorption of
H2S and CO2 in the aqueous solution. Several alkanolamines solutions have been widely
used in gas sweetening system.

1. Monoethanolamine (MEA)
2. Diethanolamine (DEA)
3. DIglycolamine (DGA)
4. Di-isopropanolamine (DIPA)
5. Methyl diethanolamine (MDEA)
6. Triethanolamine (TEA)
7. Glycol plus amine solution.

MEA and DGA react with H2S, CO2 and COS directly. DEA and DIPA react with H2S, CO2
and some COS directly. While MDEA and TEA are reacted with H2S directly, CO2
indirectly and a little COS. The following factors should be considered for evaluation and
decision making as a general approach to all sour gas sweetening treatment installations:

1. Air pollution regulations regarding H2S removal;

2. Type and concentration of impurities in sour gas;
3. Specification of treated gas (sweet gas);

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 6 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

4. Temperature and pressure at which the sour gas is available and at which the
sweetened gas should be delivered;
5. Volume of the gas to be treated;
6. Hydrocarbon composition of sour gas;
7. Selectivity required for acid gas removal;
8. Capital cost and operating cost;
9. Liquid product specifications (where application).

Below is discussed some alknolamines which use in gas sweetening systems

A. Monoethanolamine (MEA)

MEA is the strongest base of alkanolamines and reacts most rapidly with acid gasses,
and this is why MEA is the first choice in gas sweetening system. MEA have 1.7 times
more capacity for acid gases on a weight basis than DEA or DGA. Therefore a lower
amine solution circulating rate can be used when amine treating with MEA compared to
treating with DEA or DGA. MEA has a good thermal stability, can easily be reclaimed
from contaminated solutions, good COS removal and less expensive than DEA and DGA.
There some things that should be considered when using MEA:

1. MEA should commonly be used as a 10 to 20% solution in water.

2. The acid gas loading should usually be limited to 0.3 to 0.4 moles acid gas per
mole of amine for carbon steel equipment.
3. MEA’s degradation products are very corrosive. COS, CS2, SO2 and SO3 can
partially deactivate MEA, which may essentially require to be recovered with a
reclaimer.
4. MEA has a high pH that makes MEA produce gas containing less than ¼ grains
H2S per 100 S.ft3 of acid gas at very low H2S partial pressures.
5. MEA will easily reduce acid gas concentrations to Pipeline Specifications (0.25
grains per 100 S.ft3). By proper design and operation, the acid gas content can be
reduced as low as 0.05 grains per 100 S ft3).

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 7 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

6. The heat of reaction for CO2 in MEA is about 1930 kJ/kg of CO2 (460 kcal/kg of
CO2).

B. Diethanolamine (DEA)

DEA is a secondary alkanolamine, it has a reduced affinity for H2S and CO2. DEA has
very low vaporization losses and good stability in the presence of CO2, COS and CS2.
Degradation reaction with CO2, COS, and CS2 proceed at a much slower rate and the
products are non corrosive, thus reclaiming is not need to control the level of DEA
degradation products.

DEA is not selected when the absorber feed stream contains high levels of strong acid
(chlorides, SO2, SO3, thiocyanic acids), organic acids (formic, acetic, nepthanic acids),
CO, oxygen and cyanides. Because they are react with DEA to form heat stable salts
(HSS) which are stable at regenerator conditions. HSS can cause loss of DEA, solution
foaming and localized corrosion. DEA is seldom chosen for application where reclaiming
will be needed to control the buildup of HSS due to DEA’s low volatility need a high
vacuum reclaimer to avoid excessive reclaiming temperature. There some things that
should be considered when using DEA:

1. DEA is commonly used in the 25 to 35 mass percent ranges.

2. The loading for DEA is limited to 0.3 to 0.4 mole/mole of acid gas for carbon steel
equipment.
3. When using stainless steel equipment, DEA can safely be loaded to equilibrium.
This condition can be considered for carbon steel equipment by adding inhibitors.
4. The degradation products of DEA are much less corrosive than those of MEA.
5. COS and CS2 may irreversibly react with DEA to some extent.
6. DEA has a reduced affinity for H2S and CO2. As a result, for some low pressure
gas streams,
7. DEA cannot produce Pipeline Specification gas.
8. DEA will be selective toward H2S and will permit a significant fraction of CO2 to
remain in the product gas.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 8 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

9. The heat of reaction for DEA and CO2 is 151 kJ/kg of CO2 (360 kcal/kg of CO2)
which is about 22% less than for MEA.

C. Diglycolamine (DGA)
DGA is a primer alkanolamine, it has much high molar concentration that can be used in
solution without excessive DGA losses due to degradation and without excessive
corrosion rates. This allows more acid gases to be absorbed per gallon solution in lower
solution circulation rates (cost saving and investment savings). DGA has a very low
freezing point which is good for cold climates. Also provides partial dehydration of the
stream being treated. DGA has good thermal stability, can be reclaimed from
contaminated solutions, and good COS removal. DGA is better mercaptan removal due to
of high concentrations of DGA in solution which increases the solubility for higher
molecular weight mercaptans in the DGA solution.

The advantages of DGA are its high solubility of gaseous and liquid carbon especially in
C5+ hydrocarbons. It will result in higher hydrocarbon losses in the vapor from the rich
solution hydrocarbon flash/skimming drum and in regenerator overhead acid gas stream.
Higher hydrocarbon levels in the DGA regenerator overhead acid gas increase the risk of
operating problems in the downstream sulfur recovery unit. There some things that should
be considered when using DGA:

1. DGA is generally used as 40 to 60 mass percent solutions in water.

2. For gas streams with acid gas partial pressures, absorber bottoms temperatures
as high as 82°C and above can occur. This will reduce the possible loading.
3. DGA has a tendency to preferentially react with CO2 over H2S.
4. DGA has a higher pH than MEA and thus can easily achieve 6 mg H2S/ Sm³ gas
(0.25 grains per 100 S.ft3) except in some cases where large amounts of CO2 are
present relative to H2S.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 9 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

The following factors should be considered when selecting an amine for a sweetening
application as outlined here in under:

1. The pressure and acid gas content of the sour gas as well as the purity specification
for the product gas.
2. MEA is used for plants where the inlet gas pressure is low and Pipeline Specification
gas or total removals of the acid gases are required. MEA is not preferred for its high
heat of reaction and lower acid gas carrying capacity per unit volume of solution.
3. DEA is used for its lower heats of reaction, higher acid gas carrying capacity and
resultant lower energy requirements. Its potential for selective H2S removal from
streams containing CO2 has not fully been realized.
4. DGA has very high gas carrying capacity usually produces very reasonable net
energy requirements although has high heat of reaction. DGA also has a good
potential for absorbing COS and some mercaptans from gas and liquid streams, and
because of this, DGA has been used in both natural and refinery gas applications.
5. MDEA, with its some outstanding capabilities, resulting from its low heat of reaction,
can be used in pressure swing plants for bulk acid gas removal. MDEA is currently
best known for its ability to preferentially absorb H2S.

H2S + R2NCH3 R2NHCH4+ + HS

CO2 + H2O + R2NCH4+ R2NCH4+ + HCO3-

Figure 1: Reaction between acid gas and amine

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 10 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Process Flow Scheme

Typically flow scheme for gas sweeting system is shown in figure 2. The hydrocarbon or
H2 rich stream to be treated is fed into the bottom of absorber tower (scrubber) and is
passed upward through the packed or trayed absorber, counter current to the amine
solution to insure intimate contacting. The amine solution absorbs H2S, CO2, and acid
gas. The treated carbon stream which has a low acid gas content (sweet) flows overhead
from the top of the absorber tower.

The solution leaving the bottom of the absorber tower has a high loading H2S and CO2
(rich solution) is sent to hydrocarbon flash/skimming drum, which also provides rich
solution surge capacity then preheated in an exchanger and fed to the low pressure
regenerator near the top of tower. Reboiler adds heats to the bottom of the regenerator
causing part of the solution vaporizes thereby providing an upward flow of striping vapors
in the regenerator tower, and then condense partly in the regenerator to supply heats for
the endothermic acid gas desorption reactions and for heating the solution to regenerator
bottom temperature.

Water vapor and acid gases striped from the rich solution flow overhead from the top of
the regenerator tower and are cooled to condense a major portion of the water vapor.
This condensate is collected and continually recycled back to the system to prevent water
loss from the system and thereby maintain unit water balance. It is refluxed back to the
top of regenerator, above the rich solution feed location, to remove traces of alkanolamine
vapor from the overhead stream leaving the top of the tower.

The hot solution leaving the bottom of the regenerator tower has low loading H2S and
CO2 (lean). After partial cooling by heat exchange with the rich solution, lean solution is
cooled by heat exchange with cooling water or air and then pumped to the top of the
absorber tower to complete the solution circuit. Many operating problem can be avoid if
surge volume and filtering are provided for the lean solution and lean solution is fed to
each absorber under flow control. With MEA and DGA, a slipstream of mine solution from
the regenerator bottom is usually fed to a reclaimer purification but if using DEA, the
reclaimer are seldom used.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 11 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Sweet
product Overhead
condenser
Acid gas to
Overhead
disposal
KO drum

Lean Overhead
solution KO drum
Regenerator
tower
Knockout Condensed
Hydrocarbon
purge
Reflux pump
Absorber Condensate
Tower purge

Rich/lean
exchanger

Sour KO L.P Steam

Flashed Steam
Drum
hydrocarbon Reboiler
vapor
Reclaimer
MEA/DGA
Knockout
Sludge
Flash/Skimming Rich Lean cooler
Drum solution

Lean filter

Skimmed
hydrocarbon
liquid Lean Lean
pump surge/Storage
tank
Figure 2: Process flow scheme of gas sweetening

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 12 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Good performance of a gas sweetening systems requires proper choice and control of
process operating conditions. Bellows are variables which affect for gas sweetening
systems:

1. Type of alkanolamine
2. Alkanolamine concentration in solution
Excessive alkanolamine have negative effects which place a practical limit on solution
strength, requires the use of more stainless steel materials, temperature rise in the
absorber due to exothermic heat of the absorption reactions thereby rich end pinch
can occur in the absorber. Also causing higher lean solution loadings and higher acid
gas levels in the absorber overhead product or higher steam requirements for the
regenerator reboiler.
3. Rich solution acid gas loading or solution circulation rate
Increasing the rich solution loading will permit less solution to be circulated, the
solubility of hydrocarbon in the rich amine solution leaving the bottom of the absorber
decreases. Therefore, it is desirable to use as high a rich solution loading as is
feasible. The acid gas loading in the rich solution should be limited because these
factors:
 The acid gas equilibrium vapor pressure or concentration over the rich solution
must be sufficiently lower than actual inlet partial pressure to continue the
absorption process.
 A higher solution rate will provide a lower bulge temperature. At the bulge
temperature, the equilibrium vapor pressure or concentration of acid gases over
the down-flowing solution reaches its highest value. If the bulge temperature is too
high, no absorption can take place at all point of the tower.
 Higher loadings tend to cause higher rates of corrosion.
 Too low a solution rate can result in blowing in trayed towers or poor liquid
distribution in packed towers.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 13 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

4. Lean solution acid gas loading

Lower equilibrium acid gas concentrations in treated product leaving the absorber can
be achieved by lower lean solution loadings (lower H2S loadings in lean solution).
Lower H2S loading in the lean solution are obtained with higher regenerator reboiler
heat duty, higher CO2/H2S ration in the absorber feed stream, higher regenerator
pressure (if CO2/H2S ratio <0.33) and lower regenerator pressure (if CO2/H2S ratio ≥
0.33). with a higher ratio of CO2 to H2S pickup by solution, stripping H2S from the
amine solution in the regenerator is easier.
5. Acid gas concentrations in absorber feed
When CO2 present, the amine solutions are more corrosive but striping of H2S is
easier (CO2/H2S ratio higher). A lower lean solution H2S loading is possible for a given
reboiler heat duty or a lower reboiler heat duty can be used to obtain a given lean
solution H2S loading.
6. Other contaminants in absorber feed
7. Absorber temperature
The absorber should be run as low as possible. Lower temperature shift the
equilibrium of exothermic reactions allowing more acid gas absorption to occur at a
given acid gas partial pressure or concentration over the solution. Large changes in
the absorber temperature may indicate a serious operating problem. Absorber
temperatures are affected by:
 Feed stream temperature at absorber inlet should be maintained as low as
possible
 Low lean solution temperature but do not too low in hydrocarbon gas treating,
hydrocarbon will condense in absorber result foaming.
 Heat released by acid gas absorption reactions
 Ratio of solution circulation mass rate to feed mass rate. If feed content very low
acid gas, the feed mass rate may be large relative to the solution mass rate.
8. Absorber pressure
The absorber pressure is selected to meet the needs of the upstream and
downstream units. For gas treating, increasing the absorber pressure decreases the
ratios of acid gas pa5rtial pressure to total pressure in the absorber overhead which

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 14 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

results in lower acid gas concentrations in the overhead product thus improve acid gas
removal by the amine solution. For liquid hydrocarbon treating, the absorber operating
pressure must be sufficiently high to prevent hydrocarbon vaporization in the
absorber, including at the bulge temperature.
9. Regenerator temperature
Regenerator is desirable to operate at the lowest practical temperature to minimize
alkanolamine decomposition and corrosion. The regenerator reboiler must be design
to ensure that metal temperatures in the reboiler do not exceed 300oF and that local
hot spots do not occur in the tube bundle. The regenerator tower bottom temperature
must be sufficiently high to boil the amine solution, at the regenerator bottom
pressure, to generate stripping steam flow up the tower.
10. Regenerator pressure
The regenerator is operate at a pressure as low as practical to minimize the
temperature in the tower thereby reduce corrosion and alkanolamine degradation.
Also lower acid gas partial pressure favors desorption of the acid gases from amine
solution and reduce the MEA and DGA reclaiming temperatures. Higher regenerator
pressure increase the regenerator bottom temperatures resulting in easier solution
regeneration. A typical design regenerator operating pressure is 10 – 15 psig at the
tower top.
11. Regenerator reboiler heat duty
The regenerator reboiler heat duty should be minimize to reduce costs and grassroots
units. Regenerator reboiler heat duties typically equivalent ponds of 60 psig saturated
steam (905 Btu/lb) per gallon circulating amine solution. The reboiler heat duty includes:
1) the sensible heat required to raise the temperatures of the rich amine feed, the reflux,
and the makeup water to the temperature of the reboiler, 2) the heat of reaction to break
chemical bonds between the acid gas molecules and the amine, and 3) the heat of
vaporization of water to produce a stripping vapor of steam.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 15 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Reducing the solution circulation rate reduces the reboiler duty by maximizing the acid
gas absorbed per volume of rich solution.

a. Minimum duty for stripping acid gases

Stripping steam must be provided at a sufficient rate to the bottom of the
regenerator in order to give very low acid gas partial pressure in the vapors above
the regenerator bottom trays. These acid gas partial pressure must be lower than
the equilibrium must be lower than the equilibrium acid gas vapor pressures over
the lean amine solution on the bottom trays to provide a driving force of absorption
of acid gases from solution. The reboiler steam ratio must be high enough to meet
the regenerator heat balance criterion, otherwise stripping will be impaired.
b. Minimum duty for regenerator heat balance
The heat supplied to the regenerator reboiler must satisfy the regenerator heat
balance to providing adequate stripping of the amine solution. If heat supplied is
less than required, solution regeneration will degenerate. If more than required, the
additional heat input will pass overhead from regenerator tower and be removed by
the regenerator overhead condensers. Two conditions must be met to satisfy the
regenerator heat balance: the vapor temperature cannot be less than the rich
solution feed temperature, the steam partial pressure in the vapor stream cannot
be less than the equilibrium steam vapor pressure over the rich solution feed.
The minimum heat duty is a function of regenerator pressure, the difference
between the acid gas loading in the rich and lean solution, and the temperature
difference between the hot lean solution entering the rich/lean exchanger and the
hot rich solution leaving the rich/lean exchanger.
12. Regenerator reflux
The regenerator is operated at total reflux, all the liquid condensed from the overhead
is pumped back to the top of the tower above the rich amine solution feed point.
Recycle of this condensate back to the amine unit helps reduce alkanolamine losses.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 16 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

13. Alkanolamine losses/makeup

Minimizing alkanolamine losses is important to minimize alkanolamine makeup
operating costs. There are several factors which causing alkanolamine losses:
a. Vapor losses can occur in the rich solution hydrocarbon flash.skimming drum
overhead, in the regenerator overhead acid gas and in the absorber vapor
overhead. For MEA and DGA, the vapor losses can be reduced by washing this
stream with slipstream of cool regenerator reflux or lean solution.
b. Solution entrainment and alkanolamine solubility in the absorber overhead product
stream resulting liquid hydrocarbon treating losses. The losses can be minimized
by proper design of the absorber top: adequate liquid-liquid disengaging time, low
hydrocarbon velocities, and large holdup time above the low liquid-liquid interface
level.
c. Foaming and other upsets in the absorber or regenerator resulting entrainment
losses. Foaming can be controlled by using anti-foam agent and clean solution.
d. Reactions with contaminants in the feed, makeup water, and thermal
decomposition resulting chemical losses. The losses can be reduced by proper
choice of alkanolamine, water washing of the absorber feed to remove acids,
reclaiming MEA and DGA, for unit without reclaimer by occasional caustic addition
to the circulating solution. To prevent reaction between oxygen and alkanolamine
can using an internal floating roof or inert gas blanketing in surge tanks and using
only deaerated water.
e. Cleaning of equipment (reclaimers, solution filters, carbon treaters, and heat
exchanger)
f. Leaks, spills, solution purge steam, unit startsups/shotdowns. The losses can be
minimized by proper equipment design and maintenance, proper procedures, and
proper unit monitoring.
14. Water balance – water losses/purging/makeup
The net water flow into or out of the amine treating unit must be controlled to maintain
the desired alkanolamine concentration in the circulating amine solution. Makeup
water or steam addd to the amine treating unit must be pure (free oxygen, salts,
chlorides, organic chemicals, minerals, particulates, iron, etc). Steam, steam
condensate (demineralized) and deaerated are recommended for rated makeup

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 17 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

15. Solution purification

The advantages of the amine process are:

1. It is a continuous circulating system of smaller rate than some other processes

2. Theoretically, it is a simple exothermic-endothermic reversible chemical reaction
3. It will remove all hydrogen sulphide from the gas to lead standards, below 0.05
grains, at contact pressure of about 100 psi and above. At lower pressure,
complete removal of sulphide from the gas stream is not always achieved because
of partial pressure equilibrium limitations

The disadvantages of amine process are:

1. The amine is subject to vaporization and other losses that can be expensive
replenish.
2. Like any hydrogen sulphide removal plant, the amine process is subject to
expensive corrosion problems. A well designed amine plant will have less
corrosion than a poorly designed plant, but nevertheless, will have some corrosion.
3. Amine will remove carbon dioxide that might better be left in the gas.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 18 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

DEFINITIONS

Absorption - A separation process involving the transfer of a substance from a gaseous

phase to liquid phase through the phase boundary.

Acid gases - Impurities in a gas stream usually consisting of CO2, H2S, COS, RSH and
SO2. Most common in natural gas are CO2, H2S and COS.

Acid gas loading - The amount of acid gas, on a molar or volumetric basis, which will be
picked up by a solvent.

Adsorption - A separation process involving the removal of a substance from a gas

stream by physical binding on the surface of a solid material.

Antifoam - A substance, usually a silicone or long-chain alcohol, added to the treating

system to reduce the tendency to foam.

Absorber/Contactor/Scrubber - Tower in which aqueous amine solution is contacted

with hydrocarbon or H2 rich phase to remove contaminants, mostly H2S and CO2.

Alkanolamine - Organic amine which contains at least one alcohol group and one amine
group, e.g. MEA, DEA DGA.

Amine Treating - Process in which an aqueous alkanolamine solution is used to remove

components mostly H2S nad CO2 from hydrocarbons.

Anti Foam - Surface active agents used to suppress foaming of a solution. Usually used
in small concentrations ( typically 10 wppm or less ).

Blowing - Condition in a tower in which a fine dispersion or fog of liquid is entrained from
one tray to tray above. It is caused by excessive vapor velocities through tray openings at
relatively low liquid rates. Blowing causes poor vapor/liquid contacting which reduces
tower efficiency.

Bubble Point - Temperature (for a given pressure) or pressure (or a given temperature)
at which the first bubble of vapor appears from a liquid.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 19 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Bulge Temperature - Maximum amine solution temperature in an absorber tower. The

temperature of amine solution increases as it flows down due to heat released by acid
gas absorption.

Degradation - Loss of desirable alkanolamine properties which occurs during usage.

Alkanolamines degrade by reacting with CO2, COS, CS2, O2, etc. to form undesirable
products.

Degradation products - Impurities in a treating solution which are formed both reversible
and irreversible side reactions.

Dew Point - For agiven pressure, temperature at which the first drop of condensate forms
from vapor.

Entrainment - Small droplets or particles of one phase carried in astream of another

phase, usually liquid droplets in a gas stream, due to incomplete phase separation.

Flooding - Unstable condition in which liquid ( e.g.amine solution ) builds up in a tower

until the tower is essentially full. It is caused by excessive vapor or liquid rate through the
tower.

Foaming - Condition in which amine solution froth is formed and does not collapse.
Usually caused by contaminants, such as heavy hydrocarbons, in solution. Foaming
decreases tower throughput capacity or efficiency.

Heat of Reaction - Heat released by reactions during absorption of acid gases amine
solution or heat required by reactions during desorption of acid gases from amine
solution.

Heat Stable Salts (HSS) - Salts of alkanolamine are not regenerable, i.e. do not
decompose in the regenerator. HSS are formed by reaction of alkanolamines with acids
stronger than H2S or CO2, such as SO2, SO3, chlorides, thiosulfates, ferrocyanates,
thiocyanic, acids etc.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 20 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Hydrocarbon Flash/Skimming Drums - Drum(s) designed to reduce hydrocarbon

concentration in rich amine solution from the absorber bottom. Pressure is reduced in the
drum(s) to flash off light hydrocarbon vapors. The skimming drum is designed to separate
out a liquid hydrocarbon phase from amine solution.

Knockout ( K.O ) Drum - Drum for disengaging entrained liquid droplets from a stream of
a different phase, usually a gas stream.

Lean End Pinch - Condition in the top of an absorber where the actual vapor pressure (
or concentration ) of acid gas over lean amine solution is very close to the equilibrium
partial pressure ( or concentration ) of acid gas in the absorber overhead product, thus
limiting absorption of additional acid gas into the amine solution.

Lean Solution - Regenerated amine solution, i.e. regenerator bottoms, which has low
acid gas concentrations.

Lean Solution Cooler - Exchanger used to cool lean amine solution from the rich/lean
exchanger before the lean solution is fed to top of the absorber tower.

Liquefied Petroleum Gas (LPG) - Any material having a vapor pressure not exceeding
that allowed for commercial propane composed predominantly of the following
hydrocarbons, either by themselves or as a mixtures: propane, propylene, butane (normal
butane or isobutane) and butylene, as a by-product in petroleum refining or natural
gasoline manufacture.

Mercaptan - A hydrocarbon group (usually a methane, ethane, or propane) with a sulfur

group (-SH) substituted on a terminal carbon atom.

Minimum Heat Duty or Steam Rate/Requirement - Reboiler heat duty or steam rate
sufficient to satisfy regenerator tower heat balance plus a small excess necessary for
regenerator control.

Organic Acid - Carboxylic acid, with molecular formula RCOOH where R is a hydrogen
atom or alkyl group, e.g. formic, acetic, oxalic or naphthenic acid.

Overhead - Stream exiting from top of a vessel, usually a tower or knockout drum.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 21 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Overhead Condensate - Water, saturated with H2S and CO2, which is condensed out of
regenerator overhead vapors by cooling. Recycle of this condensate helps maintain water
material balance in the amine treating unit.

Packing - Inert solids with high surface area/volume used to improve contacting of amine
solution with another phase in a tower.

Pinch - Condition in atower where there is close approach to equilibrium, i.e. there is a
small difference between the actual vapor pressure ( or concentration ) of acid gas over
amine solution and the equilibrium acid gas partial pressure ( or concentration ) over
amine solution.

Reboiler - Heat exchanger ( usually kettle type ) which takes amine solution from bottom
of regenerator and boils it to supply vapors for acid gas stripping from and heating of the
amine solution. Vapors from reboiler return to bottom of regenerator and liquid from
reboiler is lean solution. Steam usually supplies energy to reboiler.

Reclaimer - Vessel for separating alkanolamine from degradation products, heat stable
salts, and solids by batch distillation. Alkanilamine and water distilled from the reclaimer
are returned to the amine treating unit.

Reflux Ratio - Molar ratio of condensed water to acid gas vapors leaving the regenerator
over head condenser.

Regenerator/Reactivator/Stripper - Tower in which acid gases are desorbed from

amine solution by sripping.

Rich End Pinch - Condition in the absorber bottom where the actual acid gas partial
pressure ( or concentration ) above rich amine solution is very close ( or equal ) to the
equilibrium acid gas partial pressure ( or concentration ) in the feed to the absorber, thus
limiting absorption of more acid gas into amine solution.

Rich/Lean Exchanger - Heat exchanger which utilizes heat from hot lean amine solution,
leaving the regenerator reboiler, to preheat rich solution feed to the regenerator.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 22 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

Rich/Lean (Temperature) Approach - Difference between the temperatures of rich

solution leaving and lean solution entering the rich/lean exchanger(s).

Rich Solution - Amine solution which has passed through the absorber, i.e. absorber
bottoms, and has high concentration of acid gas.

Sour gas - Any gas stream which containing acid gas components H2S and/or NH3, e.g.
absorber feed,regenerator overhead condensate, wash water etc.

Steam Ratio - Ratio of regenerator reboiler steam rate to circulating lean solution rate.
The reboiler steam rate is frequently converted to the equivalent rate of 60psig saturated
steam ( 905 Btu/Lb ).

Stripping Steam - Steam, due to amine solution vaporization in the reboiler, entering the
regenerator bottom from the reboiler. Sripping steam rate is set by the reboiler steam
rate.

Surge/Storage Drum or Tank - Vessel which provides amine solution holdup capacity
for the amine treating unit.

Sweet gas - A gas stream which has acid gas components removed to an acceptable
level

Water balance - Maintenance of desired inventory of water in amine treating unit. It

requires controlling net flow of water into or out of unit to give desired concentration of
water in amine solution circulating through unit.

Weeping - Condition in a tower in which liquid continuously leaks through tray openings
to the tray below. It is caused by vapor velocities through tray opening which are too low
to support the liquid level on the tray. Excessive weeping reduces vapor/liquid contacting
and therefore tower efficiency.

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 23 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

NOMENCLATURES

a Heat carrying capacity of amine solution, btu/hoF

Acooler Amine cooler Area, ft2
AHX Rich/lean heat exchanger Area, ft2
AR Reboiler (Direct Fired) Area, ft2
Areflux Reflux condenser Area, ft2
b Heat carrying capacity of the absorber feed stream, btu/hoF
CAG Acid gas concentration in sour gas, mole%
CAGout Acid gas concentration in overhead product, mole%
Cpfeed The absorber feed specific heat, btu/mole oF
%CO2 CO2 concentration in sour gas, %
Da The diameter of an amine plant absorber, in
DRA The diameter of the regenerator above the feed point, in
DRB The diameter of the regenerator below the feed point, in
FAP Main amine solution pumps, HP
FBP Amine booster pumps, HP
FR Reflux pumps, HP
FAC Aerial cooler, HP
GLS Lean solution rate, gph
GPM Amine circulation rate, gpm
ΔHabs Heat released in absorber, btu/h
ΔHBulge Heat released in absorber due to H2S plus CO2 absorption into amine
solution below bulge temperature location, btu/h
ΔHH2S Heat reaction of H2S, btu/mol
ΔHCO2 Heat reaction of CO2, btu/mol
HHX Rich/lean heat exchanger Heat Duty, Btu/hr
Hcooler Amine cooler Heat Duty, Btu/hr
HR Reboiler (Direct Fired) Heat Duty, Btu/hr
Hreflux Reflux condenser Heat Duty, Btu/hr
%H2S H2S concentration in sour gas, %
LH2S lean H2S loading in lean solution, mol/mol
LCO2 lean CO2 loading in lean solution, mol/mol
LH2Srich H2S loading in rich solution, mol/mol
LCO2rich CO2 loading in rich solution, mol/mol
LH2S lean H2S loading in lean solution, mol/mol

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
 Page 24 of 66
Kolmetz Handbook
KLM Technology Of Process Equipment Design
Group
Rev: 01
Natural Gas Sweetening Systems
Practical Engineering Selection, Sizing
Guidelines for Processing Plant
Solutions and Troubleshooting
March 2012
www.klmtechgroup.com (ENGINEERING DESIGN GUIDELINES)

LCO2 lean CO2 loading in lean solution, mol/mol

LH2S+CO2rich Rich H2S + CO2 load (estimated), mol/mol
Mwamine Amine molecular weight, lb/mol
P Contactor pressure. psia
Q Sour gas to contactor, MMscfd
Tbulge The bulge temperature, oF
TRich Rich solution temperature. oF
TFeed Feed solution temperature. oF
TLean Lean solution temperature, oF
%WAmine Amine concentration in liquid solution, wt%
z Amine solution specific heat

Greek Letters

ρLean Lean solution density, lb/gal

β Bulge temperature correlation factor

Superscript

A Area, ft2
H Heat Duty, Btu/hr
L Load, mol/mol
T Temperature, oF

These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.

This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.

View publication stats