Quick Assessment - AccurioPro ColorManager Ver.2.

0 TEST
01 of 20
Questions
00:39:27
If you want to create a printer profile that produces K with an input value of 40-
100%, which level should you select in [UCR/GCR Settings]? Choose one.

Mark
Level 4
Level 1
Level 3
Level 2
Level 5
02 of 20
Questions
00:39:18
Which of the following is true about the G7 Calibration Report for APCM2? Choose
two.

Mark
CMY wΔCh Ave. / Max: Lower values are better.
Correction Curves: CMY and K are displayed separately.
Paper White(a*/b*): The lower the value, the closer to pure white paper.
CMY wΔCh: Differences in hue are identified.
NPDC: C,M,Y,K are displayed separately.
03 of 20
Questions
00:39:15
Which feature hides the icon in APCM2 when the IQ-501 is installed? Choose three.
Mark
Profile Creation
Maximum Density
Calibration
Each Paper Type Color Adjustment
Density Balance
Spot Color Creation
04 of 20
Questions
Which of the following is true about the color validation of APCM2? Choose one.

Mark
Tolerances for validation can be adjusted in the service mode.
Colorimetric conditions can be set manually even if no color management presets
have been registered in advance.
In the report, target and actual values for each color patch, dE and Pass/Fail
judgment results can be confirmed.
If the Judgment Result is Pass, no report is generated.
05 of 20
Questions
00:39:09
What is the target range for measuring CMY wΔCh Ave for G7 calibration in APCM2?
Choose one.

Mark

≦3.5

≦3.0

≦1.5
06 of 20
Questions
When adding a printer in APCM2, which of the following can be set up in the same
wizard following the addition of a printer? Choose two.

Mark
Spot Color
Color Management Preset
Target Configuration
Custom Target Profile
Custom RGB Source Profile
07 of 20
Questions
Which of the following is correct as a precaution when performing profile creation
with APCM2? Choose two.

Mark
When using the IQ-501, the paper feed direction must be the same as the chart
feed direction.
When using the IQ-501, eight different charts can be selected.
When printing a chart, the correct paper size must be selected that is compatible
with the chart size.
The reference paper listed in the service manual must be used.
08 of 20
Questions
Which functions in APCM2 are recommended to use the color management presets
(default is [Use])? Choose two.

Mark
Spot Color
Validation
Calibration
Color Related Settings Management
Maximum Density
Density Balance
09 of 20
Questions
Which of the following is a correct precaution when performing a maximum density
in APCM2? Choose one.

Mark
Even when the user's reference paper is used, if the Judgment Result is [Fail], adjust
the Maximum Density until it becomes [Pass].
Whatever paper the user uses, it must match the target values in the service
manual.
Prepare at least 10 sheets of POD Gloss Coat 128gsm to put under the chart.
Before measuring, clarify the measurement points on the printed chart（Draw lines
on the chart).
10 of 20
Questions
What work is required in advance to create profiles and perform Validation in
APCM2? Choose two.

Mark
Register a custom target profile.
Register a custom spot color.
Create target configuration.
Register a custom RGB source profile.
Create a color management preset.
11 of 20
Questions
Which of the following functions cannot be performed in APCM2 without RU-518?
Choose one.

Mark
Calibration
Each Paper Type Color Adjustment
Density Balance
Maximum Density
12 of 20
Questions
00:38:50
Which of the following adjustments should be performed on the APCM2 to improve
the accuracy of the Color Density Control? Choose one.

Mark
Maximum density initial adjustment
Density Balance
Profile Creation
Maximum Density
Each Paper Type Color Adjustment
13 of 20
Questions
00:38:47
What is the function to manage color-related settings registered in the controller by
APCM2? Choose one.

Mark
Management
Target Configuration
Color Related Settings Management
Calibration
Color Management Preset
Validation
Spot Color
14 of 20
Questions
What paper types are supported for calibration in APCM2? Choose three.

Mark
Textured
Envelope
Coated（gloss）
Plain Paper
Film
Fine
15 of 20
Questions
00:38:17
Which of the following is a correct note about Package Color Adjustment in APCM2?
Choose two.

Mark
When IQ-501 is connected, Package Color Manual Adjustment can be performed
with APCM2.
The target values for user's reference paper and maximum density must be those
listed in the service manual.
When RU-518 is connected, Package Color Manual Adjustment can be performed
with APCM2.
Multiple targets can be set for user's reference paper and maximum density.
When RU-518 is connected, Package Color Auto Adjustment can be performed with
APCM2.
When IQ-501 is connected, Package Color Auto Adjustment can be performed with
APCM2.
16 of 20
Questions
00:38:12
What is the maximum number of accuracy measurements for calibration with
APCM2? Choose one.

Mark
No limit to the number of times
Once
Three times
Five times
Eight times
17 of 20
Questions
00:38:10
Which of the following is the correct way to create a spot color in APCM2? Choose
three.

Mark
Create using color configuration.
Create using the IQ-501.
Select from and create a color management preset.
Create by entering CMYK values.
Select and adjust from the registered spot colors.
Create a sample by measuring the color with a Instrument.
18 of 20
Questions
Which of the following is NOT possible for a monochrome machine when performing
density balancing with APCM2? Choose one.

Mark
The same Instrument can be used as for color machines.
Measurement data can be registered directly to the main body.
Measurement data can be sent to the main body.
Colorimetric conditions can be set manually.
19 of 20
Questions
The paper size of the charts that can be used in the Exact Color calibration of
APCM2 is A4/Letter or larger.

Mark
True
False
20 of 20
Questions
00:38:03
Which of the following features does APCM2 not support for monochrome machines?
Choose two.

Mark
Validation
Density Balance
Profile Creation
Maximum Density
Each Paper Type Color Adjustment