YellowJacket Pro System

Remote Control Installation/Setup

General Information:
The radio remote control that you are installing can be used for most electrical switching and control applications. Before beginning the installation and
testing you should check that each item listed below is available and in good condition.
3.
1. Antenna: Magnetic mount antenna with 15ft of cable. 4.
2. Receiver: Usually pre-wired inside for most systems.
3. Transmitter: Hand-held controller with pushbuttons. 1.
4. Batteries: (2) AA Alkaline Batteries
5. Power Adapter: Either 120VAC to 13.5VDC Adapter, or 12VDC inline power regulator (Buckboost)
depending on customer request. 2. 5.

Wiring in Power Lines

 120VAC systems: 120VAC systems are prewired using a standard 110V plug with supplied +13.5VDC adapter.
 +12VDC Systems: The +12V adapter, or “Buckboost,” can be used for +12V systems by simply cutting the cord to length and wiring the lead with
the white stripe to +12V and the black only lead to Ground.
 24VAC Systems: Use special connectors; contact us at (724) 610-5256 or email us at [email protected] for more information.

Wiring In Control Lines

RFHero™ remote systems are wired to work with a variety of
insulation machines. To easily adapt to other makes and models, please use the provided UAX-100 adapter cable and simply use the correct plug end
for your machine. The most popular wiring convention that many insulation machine manufactures use is:

Green– Common Voltage

White– Blower/Air
Black-Material Feed

To utilize the UAX-100 simply use the following color code:

UAX-100 Function Machine Side
Green Common Voltage Green
Brown Air/Blower White
Blue Material Feed Black

Relay 1 LED Relay 1

Learn Relay 2
External Learn Button Relay 2 LED
Button
Relay 1
Fuse

Power Relay 2
Connector Fuse

Communications
LED
Antenna
Connector
Power
LED

Fuse Tester Fuse Tester

LED (w/Spare Fuse)

Operating Instructions
1. Place two (2) AA batteries in the transmitter. The LED on top will flash red a few times. Once this stops, pressing any button on the transmitter will
cause the LED on top to rapidly flash green.
2. Plug the YellowJacket Pro receiver power adapter into a powered outlet, then into the YellowJacket Pro receiver. The Power LED (red) should
now be lit.
3. After a few seconds the Communications LED should flash green three (3) times. If it flashes any other number of times, then the mode is wrong.
Please contact RFHero Support to quickly and easily resolve this.
4. Pressing a button on the transmitter will cause the LED on the top of the transmitter to flash green to indicate that the signal has been sent.
5. The Communications LED on the receiver will flash green/red (may appear orange) to indicate that a valid message has been received from the
transmitter. You may also be able to hear the relay click inside the receiver. If the lid is removed from the receiver, you will also see the relay’s
LED turn on and off as the transmitter’s buttons are pressed.
6. If the Communications LED flashes red only, the transmitter is not paired with this receiver. Please follow the directions on the next page titled,
“Pairing the YellowJacket Pro Receiver and Transmitter”.
7. Your system is now operational and ready for use!
Remote Finder Feature
***Feature is standard for Falcon Pro Systems; Feature is an optional upgrade for YJPro Systems***

When the transmitter is first powered on (i.e. putting in a fresh set of batteries) or awakened from it’s sleep state (i.e. pressing any button when
“asleep”) , it will emit a series of audible beeps to alert the operator that the Remote Finder features is activated. The remote will function normally until
one of the two following events occur:
 The operator puts the remote to “sleep”. To disable the Remote Finder feature, simply hold the OFF button down for about six (6) seconds. The
remote will respond with a series of beeps, release the OFF button as soon as the beeping begins.
 The Remote Finder feature self-activates. Unless put to sleep, after approximately 60 minutes of inactivity the transmitter will emit a series of loud
beeps at approx 1 minute intervals. This “Finder” alarm will continue for approximately 24 hours or until a button is pressed on the transmitter
(during a silent period, not when the alarm is going off). The action of pressing a button resets the 1 hour timer and the remote will function nor-
mally again until it is “put to sleep” or 1 hour of inactivity occurs again.

Please remember to put your Transmitter “to sleep” after your job is complete to avoid an unwanted alarm trigger and to preserve battery life
(or remove batteries).

Maintenance Notes
 The receiver box should be kept dry and should be periodically dusted off.
 Check the transmitter’s batteries weekly. Only use two (2) AA alkaline or equivalent rechargeable batteries. When the batteries are weak the
Transmitter’s LED will light on red and off slowly and you may notice some reduced operating range.
 Clean the antenna periodically with mild soap and water; do not immerse in water. Allow to dry completely before use.
 If unit is to be returned for service, please clean the transmitter and the receiver before sending it back. Visit www.rfhero.net and click the RMA
Link in the top right corner to issue an RMA.

Pairing the YellowJacket Pro Receiver and Transmitter (Learn Mode)

ATTENTION!
This section contains the pairing instructions for REPLACING or ADDING an additional remote
transmitter. Your new transmitter and receiver are already paired from the factory and this
procedure is unnecessary for a new YellowJacket Pro kit.

1. Locate the External Learn Button on the YellowJacket Receiver. If the External Learn Button appears not to function, or is not present, remove the
lid by unscrewing the four screws and locate the internal learn button.
2. Repeat steps 1 & 2 of the “Operating Instructions” section on the previous page. You have 60 seconds to complete the Learn Mode procedure
once step 2 is complete.
3. After the Communications LED flashes three (3) times, press and hold the Off button on the transmitter.
4. Press and hold the Learn button on the YellowJacket Pro receiver.
5. Release the Off button on the transmitter for five (5) seconds.
6. Press the Off button on the transmitter again.
7. Release the Off button on the transmitter and the Learn button on the YellowJacket Pro receiver.
8. The Communications LED on the YellowJacket Pro receiver should now flash green/red (may appear orange) when a button on the transmitter is
pressed.
9. Replace the lid and screws on the YellowJacket Pro receiver (if lid was removed).
10. The transmitter and YellowJacket Pro receiver are now paired together.

Basic Troubleshooting
 If the transmitter’s LED flashes red slowly several times then stops, the batteries should be replaced or recharged.
 Make sure that the red Power LED is lit when the YellowJacket Pro receiver is plugged in.
 If operational range seems reduced, check the antenna for a broken wire or loose connection.
 Verify that the YellowJacket Pro receiver blinks green three (3) times anytime power is turned on.
 Verify that the control cable is securely connected, properly wired and undamaged.
 Be sure to check relay and fuses if any controls are not working.
 All units contain a built-in fuse tester and spare fuse. Refer to YellowJacket Top View on previous page.
 Please visit www.rfhero.net and click on the Support tab for more help.
 Contact us for more assistance at (724) 610-5256, or email us at [email protected]

This System Qualifies for

Manufacturer Support FCC ID: QIA-YJPRO
IC: 21464-YJPRO

www.rfhero.net/support M/N: YJPRO3B

This device complies with

Email: [email protected] Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (i.)
this device may not cause harmful
Phone: (724) 610-5256 interference, and (ii.) this device must
accept any interference received, that