IBS CEQ Professional Intelligent Digital Balance Charger Balance Charger Instruction ManualINTRODUCTION INTRODUCTION Thank you for purchasing B6 Pro Balance Charger from imaxRC. This product is a rapid charger with a high performance microprocessor and professional operating software, Please read this entire operating manual completely and carefully before using this product, as it covers a wide range of information on operating and safety. Or please do use this product under supervision of a specialist! Specifications Operating voltage range’ De 11.0-18.0V, Circuit Power: Max. charge power 50W Max. discharge power 5W Charge Current Range: 0.1-5.08, Discharge Current Range: 1.0-1.0A, Current Drain for Balancing Li-Po: 300mAn/cell NiCd/NiMH Battery Cell Count: 1-15 cells Li-ion/Palymer Cell Count: 1-6 series Pb Battery Voltage: 2v, 20V Weight: 170g Dimension: 138*75*23mm onFEATURES FEATURES Optimized operating software BG Pro features the so-called AUTO function that sets the feeding current during the process of charging or discharging. Especially for Lithium batteries, it can prevent the overcharging which may lead to an explosion due to the user's mistake. It can disconnect the circuit automatically and alarm once detecting any maifunction. All the programs of this product are controlled through two way linkage and communication, to achieve the maximum safety and minimize the trouble. All the settings can be done by users! Internal independent Lithium battery balance 6 Pro has an individual-cell-voltage balancer. It is unnecessary to connect an external balancer for balance charging, During the process of discharging, B6 Pro can monitor and balance each cell of the battery pack individually, Error message will be shown and the process will be ended automatically if the voltage of any single cell is abnormal. Adaptable for Various Types of Lithium Battery B6 Pro is adaptable for various types of Lithium batteries, such as Li-ion, Li-Po and new Li-Fe series batteries. o2FEATURES: Fastand storage mode of Lithium battery Purpose to charge Lithium battery varying, fast’ charge reduce the duration of charging, while ‘store’ state can control the final voltage of your battery, so as to store for a long time and protect useful life of the battery, Maximum safety Delta-peak Sensitivity: The automatic charge termination program based on the principle of Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process will be terminated automatically. Automatic charging current limit You can set a upper limit for the charging current when charging your NiCd or NiMH battery; it is useful for the NiMH. battery of low impedance and capacity under the ‘AUTO’ charging mode. Capacity limit The charging capacity is always calculated as the charging current multiplied by time. If the charging capacity ‘exceeds the limit, the process will be terminated automatically when you set the maximum value. Temperature Threshold” The battery's internal chemical reaction will cause the temperature of the battery to rise. If the temperature limit is reached, the process will terminate * This function is available by connecting optional temperature probe, which is not included in our package. 03FEATURES: Processing time limit You can also limit the maximum process time to avoid any possible defect. Input power Monitoring To protect the car battery used as DC input power from being damaged, its voltage keeps being monitored. Ifit drops below the lower limit, the process will be ended automatically. Data store/load The data for maximum five batteries can be stored for users’ convenience. You can keep the data pertaining to program setting of the battery of continuous charging or discharging. Users can call out these data any time without any special program setting. Cyclic charging/discharging 1 to 5 cyclic and continuous process of charge -discharge or discharge-charge is favorable to battery refreshing and balancing to stimulate the battery's activity. 04Built-in ultra-thin fan Higher heat sink performance ‘Safer when Charging and discharging Lead to super cool effect ‘Scroll through the Main Menu. Input power cable out putchargelead 11-18V DC, 4mm banana plug LeD screen Balance lead sockets JST-XH ports. Balance Charger Stop any charge process Alter values Resume or start charge processes os Check the status of individual Confirm an action cell in balance charge modeUTHIUM POLYMER BALANCE CHARGE PRO GRAM CONNECTION DIAGRAM LITHIUM POLYMER BALANCE CHARGE PROGRAM CONNECTION DIAGRAM This diagram shows the correct way to connect your battery to B6 Pro charger under the balance charge program mode only. ZA WARNING: Failure to connect as shown in this diagram will damage this charger. The main battery leads must be connected to the balance lead connector as shown before charging your battery. ZX WARNING: @ It using crocodile clips as shown in above diagram, make sure they are separated with each other! 06WARNING AND SAFETY NOTES ZX WARNING AND SAFETY NOTES These warning and safety notes are particularly important. Please follow the Instructions for maximum safety, otherwise the charger and the battery will be damaged or at worst it can cause a fire. @ Never ieave the charger uncupervised when Its connected to power eupply. If any malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the operation manual @ Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration. Never drop it. @ The allowable input voltage is 11-18V DC @ This charger and the battery should be put on a heat-resistant, nohflammable and nonconduetive surface. Never place them on a car seat, carpet or similar. Keep al the inflammable and volatile materials away from operating area @ Make sure you know the specifications of the battery to be charged and discharged to ensure it meets the requirements of this charger. If the program is set incorrectly, the battery and charger may be damaged. It can cause a fire or explosion due to overcharging. The warranty is not valid for any damage or subsequent damage caused by misuse or failure to follow the procedures outlined in this manual o7WARNING AND SAFETY NOTES Nicd/NiMH Voltage level: 1.2V/cell Allowable fast charge current: 1C-2C (depends on the performance of cell) Discharge voltage cut off level: 0, 85V/cell (NiCd), 1, 0V/cell(NiMH) Li-ion Voltage level: 3.6V/cell Max. charge voltage: 4. 1V/cell Allowable fast charge current: 1C or less Min discharge voltage cut off level:.2 5V/cell or higher LiPo Voltage level: 3 7V/cell Max, charge voltage: 4.2V/cell Allowable fast charge current: 1C or less Discharge voltage cut off level: 3 OV/cell or higher LiFe Voltage level: 3. 3V/cell Max. charge voltage: 3.6V/cell Allowable fast charge current: 4C or less Discharge voltage cut off level: 2 OV/cell or higher Pb Voltage level: 2.0V/cell (Lead-acid) Max. charge voltage: 2.46V/cell Allowable fast charge current: 0.4C or less Discharge voltage cut off level: 1.75V/cell or higher osWARNING AND SAFETY NOTES @ To avoid short circuit between charge leads always connect the charge cable to the charger first, then connect the battery, Reverse the sequence when disconnecting @ Do not connect more than one battery pack to this charger at a time @ Never charge or discharge the following types of batteries. = Abattery pack which consists of different types of cells (including different manufacturers) = Abattery that is already fully charged or just slightly discharged = Non-rechargeable batteries (Explosion hazard). = Batteries that require a different charge technique from NiCd, NiMh, LiPo or Gel cell (Pb, Lead acid). = Afaulty or damaged battery. = Abattery fitted with an integral charge circuit or a protection circuit = Batteries installed in a device or which are electrically linked to other components. = Batteries that are not expressly stated by the manufacturer to be suitable for the currents the charger delivers during the charge process. 08