2 Part Thermally Conductive Silicone Gel
SilCool* XE14-C7412
XE14-C7412 is a 2 part, highly thermally conductive silicone gap filler. XE14-C7412 cures quickly
with heat or at room temperature to become a soft, repairable thermally conductive elastomer.
Key Features
High thermal conductivity
Easy to use 1:1 mix ratio
Dispensable
Cures quickly with heat or at room temperature
Soft, stress-absorbing
Repairable
Resists cracking or sagging when assembled in typical vertical positions
Typical Property Data (JIS K 6249)
UNCURED PROPERTIES XE14-C7412 (A/B)
Color Pale Pink
Mixing Ratio (by weight or volume) 1:1
Viscosity (viscometer 2rpm) Pas 820 (part A), 830 (part B)
Dispensability* g/min 25 (part A), 25 (part B)
Pot Life h 1
Cure Time (@ 23C) h 24
Cure Time (@ 70C) h 1
PROPERTIES AFTER CURE (1h @ 70C)
Density (23°C) g/cm3 3.1
Hardness (type E) 10
Hardness (00) 30
Thermal conductivity ** W/(m·K) 10.2
Bond Line Thickness (BLT) μm 250
Thermal Resistance (@250μm) mm2.K/W 22
Volume Resistivity*** Ω.cm 3 x 1013
Dielectric strength kV/mm 15
Low Volatile Siloxane (D4~D10) ppm <100
*30cc EFD syringe, 90psi, **Hot disk method, ***Momentive internal measurement
Typical property data values should not be used as specifications.
1/2
General Considerations for Use
Materials such as water, sulfur, nitrogen compounds, organic metallic salts, phosphorus compounds,
etc. contained on the surface of the substrate can inhibit curing. A sample patch should always be
conducted before proceeding in order to determine substrate compatibility. Wear eye protection when
handling uncured rubber as it can irritate eyes. In case of eye contact, immediately flush eyes
well with water and contact a physician. Maintain adequate ventilation in the work place at all times.
Storage
Store in a cool, dry place out of direct sunlight.
Keep out of the reach of children.
Packaging
XE14-C7412(A) : 330ml cartridge
XE14-C7412(B) : 330ml cartridge
*SilCool is a trademark of Momentive Performance Materials Inc
DISCLAIMER
THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS HOLDINGS INC., MOMENTIVE PERFORMANCE MATERIALS JAPAN LLC., THEIR SUBSIDIARIES AND
AFFILIATES (THE “SUPPLIERS”), ARE SOLD SUBJECT TO SUPPLIERS’ STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE SALES AGREEMENT, PRINTED ON THE BACK
OF ORDER ACKNOWLEDGMENTS AND INVOICES, OR AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD
FAITH, SUPPLIERS MAKE NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO
THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SUPPLIERS’ PRODUCTS, MATERIALS, SERVICES, RECOMMENDATIONS OR ADVICE. NOTHING IN THIS OR ANY OTHER
DOCUMENT SHALL ALTER VALLY, SUPERSEDE OR OPERATE AS A WAIVER OF ANY OF SUPPLIER’S STANDARD CONDITIONS OR SALE.
Each user bears full responsibility for making its own determination as to the suitability of Suppliers’ materials, services, recommendations, or advice for its own particular use. Each user must identify and perform all tests
and analyses necessary to assure that its finished parts incorporating Suppliers’ products, materials, or services will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral
recommendation or advice, shall be deemed to alter, vary, supersede, or waive any provision of Suppliers’ Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing
signed by Suppliers. No statement contained herein concerning a possible or suggested use of any material, product, service or design is intended, or should be construed, to grant any license under any patent or other
intellectual property right of Suppliers or any of its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product, service or design in the infringement of any patent or
other intellectual property right.
Momentive Performance Materials Japan LLC
http://www.momentive.com
Technical Answer Center (Japan) Phone: +81-276-20-6182 Fax: +81-276-31-6259
Tokyo Head Office Phone: +81-3-5544-3111 Fax: +81-3-5544-3122
Sept. 2019 / XE14-C7412
2/2
