I010425559

IOSR Journal of Electronics and Communication Engineering (IOSR-JECE)
e-ISSN: 2278-2834,p- ISSN: 2278-8735.Volume 10, Issue 4, Ver. II (Jul - Aug .2015), PP 55-59
www.iosrjournals.org
DOI: 10.9790/2834-10425559 www.iosrjournals.org 55 | Page
Development of Helmet Detection System & Smart Seat Belt
S. Anil Babu [1],
Sumathi Ayyalusamy [2]
, Rejin Ranjit Singh [3]
,
Sreejin Dharmarijan [4]
, Jason James [5]
, Mohamed Anas [6]
1&2, Assistant Professor, School of Engineering & IT, Manipal University Dubai campus, International
Academic City, Dubai, UAE.
3,4,5,6,Undergraduate Student, School of Engineering & IT, Manipal University Dubai campus, International
Academic City, Dubai, UAE .
Abstract: UAE Road accidents have increased significantly with an average of two people killed on the roads
every day [1]. The impact of accidents are further more in dune buggy ,specifically when the driver involves in
a high speed accident without wearing a helmet and seat belt. It is highly dangerous and can cause death.
Wearing a seat belt and helmet can reduce shock from the impact and may save a life. The aim of this research
work is to development of smart helmet detection system and seat belt detection system for dune buggy to avoid
or reduce the accident fatigue on drivers during accident. Driver will be unable to start vehicle without wearing
seat belt and helmet. An ultrasonic sensor HC/SR04 was used for detecting the driver helmet, ATmega328
microcontroller to control the entire safety system. The technology connects the drivers and the co passenger
seat belts with the Ignition system such that without fastening the seat belts, the dune buggy will not start. If the
driver unfastens their seat belt or helmet is removed after starting off vehicle, the control unit will disengage the
power input to the ignition switch after 30 seconds resulting in halt position.
Keywords : Road safety, Helmet Detection system, smart seatbelt. Ultrasonic sensing.
I. Introduction
Driving without fastening the seat belt was one of the most common traffic offences in Sharjah, UAE.
With 6,175 charges laid in the first six months, Young drivers were the least likely to buckle up seat belt. In the
year 2011 a survey conducted, it was found that 55% university students did not consistently wear a seat belt
[2].Research work on investigation of helmet act implemented in Thailand also figures the increase in helmet
wearers to five fold with reduction in head injuries and death to 41.4% and 20 % respectively.[6]
Smart Helmet using Global System for Mobile Communications (GSM) & Global Positioning System
(GPS) Technology for Accident Detection and Reporting system proposed by Manjesh et al. [3] vibration
sensors are place in different places of helmet where the probability of hitting is more than predetermined value
during accident driver crashes and the helmet hit the ground, GSM technology will sent an text message to
nearby hospital ambulance service.
Numerous incidents occur irrespective of any functional criteria excluding the factor of safety while
travelling on roads. The vice president of Ajman University of Science and Technology has died after a dune-
buggy accident in Al Ain. The accident happened on Friday, while Mr. Salman was enjoying a weekend in Al
Ain with friends. He hit a quad bike, Mr. Al Gergawi said. He banged his head and he also hit his rib on the
steering wheel. Friends gave him first aid while they waited for a helicopter to take him to hospital, but they
were unable to save him [4].
Smart-Tec helmet proposed by R prudhiv raj et al. [5] found that most of the 2 wheeler drivers avoid
using helmet due the excess heat inside helmet. To overcome this issue peltier module was developed to
maintain constant temperature inside the helmet. The (GPS) tracking system aids to track out the location where
the incident has happened, upon which the emergency vehicle can be reached. The two sensors incorporated in
this system are LM35D temperature sensor and ADXL3 tilt sensor. In case of sudden shocks Peltier module
activates thermo electric system preventing blood coagulation meanwhile accelerometer sensing sudden shocks
sends information through GSM and GPS modules. Inspite of all these measures the effect of accident is felt but
with reduced impact. Our research aims to prevent the major cause of accidents by implementing the simple and
positive measures such as to increase the safety factor. This paper presents the Development of Helmet
Detection System and Smart Seat Belt (DOHDSSSB) as an integrated system approach with automotives.
II. Experimental Setup of Dohdsssb
A MWG70, 150CC oil cooled dune buggy has been considered for development of DOHDSSSB. The
conventional seat belt socket was modified with seat belt detection switch. Fig.1. shows the Photo of The helmet
detection sensor was assembled on Dune buggy roof rail.

Fig. 1.Photo of Helmet Detection System
Fig.2. Shows the Block diagram of DOHDSSSB system, initially the transmitter in the ultrasonic
sensor sends ultrasonic waves, which gets reflected from the helmet and is received at the receiver. Time of
flight is calculated and is used to measure the distance between the helmet and the sensor module. Data from
sensing module is sent for processing to the processing module. With reference to distance between the sensor
and helmet, the decision making algorithm is executed at the control module. The processing module takes Yes
or No decision based on sensor signals. If the condition is No then warning light emitting diode (LED) will glow
and engine will not start. If the condition is Yes then LED will be turned off and actuation takes place in the
ignition switch will be ready for starting the engine.
Fig.2. Block diagram of DOHDSSSB system

Fig.3. & Fig.4. Representing the warning sign for fasten the seat belt and helmet on instrumental panel.
Fig.3. Schematic symbol of Seat Belt Warning sign ON
Fig.4. Schematic symbol of Helmet Warning Sign ON
Fig.5. shows the circuit diagram of DOHDSSSB. The 9V battery is connected to the Arduino board
(ATmega32) through relay. Ultrasonic sensor is connected to the processing module, in this case ATMega32.
From the ultrasonic sensor trigger is connected to one pin and the echo is connected to the other pin of the
arduino uno board. The output pin is connected to the base pin of transistor. The collector supply of the
transistor is taken from the arduino board, and then from emitter pin of transistor relay are connected.
Fig.5. Circuit Diagram of DOHDSSSB

Fig.6. Flow Chart of DOHDSSSB
If ignition key is turned ON, then seat belt switch checks whether the seat belt has been fastened or not.
If it receives positive feedback from seat belt switch then Helmet detection sensor will be actuated. The helmet
sensor checks the presence of helmet with in the range. Both these signals goes to the control unit, and it check
wheather both the sensor and the swithch is giving a positive feedback.Now the control unit give the power to
the ignition key for starting the vehicle only if it recives positive feedback. If any of the sensors gives the
negative feedback the control unit disengages the power supply to the ignition switch. Hence the vehicle will not
start until the control unit receive a positive feedback from the helmet and seat belt sensor. Working principle as
shown in the Fig.6.Flow chart of DOHDSSSB.
Fig.7. Photograph of DOHDSSSB Testing

Fig.7. shows the photograph of DOHDSSSB testing with wearing helmet and seat belt.
III. Results and Discussion
Most of the cases of Dune buggy accidents, the severities of the accidents are increased because of the
absence of helmet or seat belt. The various tests were conducted on DOHDSSSB system, by implementing this
system in dune buggy which would decrease the head injuries and prevent driver and co-driver colliding with
the interior parts of the vehicle such as steering wheel, instrumental panel and windshield and avoid the ejecting
out of passenger from the vehicle during the high speed crash accidents.
IV. Conclusions
The DOHDSSB system was designed for person of height 160 to 165 cm, repeated test was conducted
for different persons with in designated heights with helmet where ultrasonic sensor detects the presence of
helmet and ignition system turns on but in case without wearing helmet or helmet is been removed after engine
starts, the control module automatically disengaging the ignition system thus leads the engine to stop, the total
cost of DOHDSSSB system is 150 AED, so this can be implemented in as retrofitted in commercially available
vehicles. Thus it can be concluded that DOHDSSSB system when incorporated into the Dune buggy will
effectively increase the safety of the driver and co-driver.
References
[1]. UAE road accidents [online] March 11 2015. http://7days.ae/two-killed-day-uae-road-accidents.
[2]. Seat belt is the new ignition switch [online] February 21, 2012.
[3]. http://www.thenational.ae/news/uae-news/seat-belt-is-the-new-ignition-switch-in-sharjah-tests
[4]. Manjesh, Prof.Sudarshan Raj, Smart Helmet sing GSM & GPS technology for Accident Detection
[5]. And Reporting System, International Journal of Electric and Electronic Research, ISSN 2348-6988, Vol.2 Issue 4, Pages 122-127.
[6]. Road accident happened in UAE [online] February 10, 2013.
[7]. http://www.thenational.ae/news/uae-news/golden-boy-of-ajman-killed-in-dune-buggy-accident
[8]. R.Prudhiv Raj, Ch. Krishna Kanth, A.Bhargav Aditya and K.Bharath, Smart-Tec Helmet,
[9]. Advance in Electronic and Electric Engineering, ISSN 2231-1297, Volume 4, Number 5(2014), Pages 493-498.
[10]. M. Ichikawa, W. Chadbunchachai, and E. Marui, “Effect of the helmet act for motorcyclists in Thailand,” Accid. Anal. Prev., vol.
35, no. 2, pp. 183–189, 2003.

I010425559

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to I010425559 (20)

More from IOSR Journals (20)

Recently uploaded (20)

I010425559