40120140503012

International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976 –
6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 3, March (2014), pp. 94-101 © IAEME
94
PERFORMANCE ANALYSIS OF PILOT-AIDED MIMO-OFDM LTE
DOWNLINK SYSTEM USING HYBRID LS-LMMSE TECHNIQUE
Shraddha Patel1
, Vijay K.Patel2
, Dr. D.J.Shah3
1&2
Department of EC Engineering, Ganpat University, Mehsana
3
Director, Shruj LED Technologies, Ahmedabad
ABSTRACT
This paper focuses on the channel estimation in OFDM system and it implemented by using
pilot type channel estimation by hybrid LS-LMMSE. A LTE system is basically MIMO-OFDM
system, where a cyclic prefix is inserted at the beginning of each OFDM symbol in order to suppress
both inter-carrier interference (ICI) and inter symbol interference (ISI). The inserted CP is usually
longer or equal to the channel length but in some cases, the CP can be shorter. In case of LS and
LMMSE channel estimation technique, simulation results shows that LMMSE performs better than
LS estimator where cyclic prefix is equal to or longer than the channel length. In other case, LMMSE
gives better performance than LS only for low SNR values and for high SNR value, LS gives better
performance. Therefore, a hybrid LS-LMMSE channel estimation technique is to reduce the effect of
the channel length on system. Simulation results for hybrid system shows its true efficiency and
specially for the case where the channel length exceeds the cyclic prefix length.
Keywords: MIMO, OFDM, Channel Estimation, Channel Length, Cyclic Prefix, Hybrid
LS-LMMSE.
1. INTRODUCTION
Over the last few decades, due to the increasing demand for high speed data and widespread
network access in mobile communications, there has been tremendous ongoing research in the field
of cellular communications which has resulted in achieving significant developments. Orthogonal
Frequency Division Multiplexing (OFDM) is most commonly employed in wireless communication
systems because of the high rate of data transmission potential with efficiency for high bandwidth
and its ability to combat against multi-path delay. To combat the effect of frequency selective fading,
MIMO is associated with orthogonal frequency-division multiplexing.
(OFDM) technique. OFDM is modulation technique which transform frequency selective
channel into a set of parallel flat fading channels. A cyclic prefix CP is added at the beginning of
each OFDM symbol to eliminate ICI and ISI. [1]
INTERNATIONAL JOURNAL OF ELECTRONICS AND
COMMUNICATION ENGINEERING & TECHNOLOGY (IJECET)
ISSN 0976 – 6464(Print)
ISSN 0976 – 6472(Online)
Volume 5, Issue 3, March (2014), pp. 94-101
© IAEME: www.iaeme.com/ijecet.asp
Journal Impact Factor (2014): 7.2836 (Calculated by GISI)
www.jifactor.com
IJECET
© I A E M E

95
LTE (Long Term Evolution) is the next generation MIMO-OFDM based system. LTE
downlink system adopts Orthogonal Frequency Division Multiple Access (OFDMA) as a access
technique. LTE Downlink system is MIMO-OFDM based which delivers high data rates of up to
100Mbps for 2x2 MIMO systems.[2]
Channel estimation is an important part for the design of receivers in mobile communication
systems. In order to recover the transmitted information correctly, the effect of the channel on the
transmitted signal must be correctly estimated. In most of research work, the CP is equal or longer
than the channel length but it is also important to study the performance of MIMO-OFDM system
where the CP length is shorter than channel length. So that this task becomes more difficult because
of ICI and ISI.
There were many articles based on the channel estimation for LTE system. Also the
performance of LS and LMMSE technique for LTE Downlink system under the effect of channel
length was studies in [2].
In this paper, we propose a hybrid LS-LMMSE channel estimation technique which is robust
to the channel length effect.
Organization of paper is like this, an overview of LTE Downlink system is described in
section II. A LTE MIMO-OFDM system model is given in section III. The LS and LMMSE channel
estimation techniques are discussed and description of the proposed hybrid technique is given in
section IV. Section V gives the simulation results of both the systems. The conclusion is given in the
last section.
2. LTE DOWNLINK PHYSICAL LAYER
LTE physical layer will provide peak data rate in uplink up to 50 Mb/s and in downlink up to
100 Mb/s with a scalable transmission bandwidth ranging from 1.25 to 20 MHz to accommodate the
users with different capacities. In order to improve the spectral efficiency in downlink direction,
Orthogonal Frequency Division Multiple Access (OFDMA), together with multiple antenna
techniques are exploited. LTE air interface exploit both the time division duplex (TDD) and
frequency division duplex (FDD). Figure 1 shows the structure of the LTE radio frame. The duration
of one frame in LTE Downlink system is 10 ms. Each LTE radio frame is divided into 10 sub-frames
of 1 ms. As described in Figure 1, each sub-frame is divided into two time slots, each with duration
of 0.5 ms. Each time slot consists of either 7 or 6 OFDM symbols depending on the length of the CP
(normal or extended). In LTE Downlink physical layer, 12 consecutive subcarriers are grouped into
one Physical Resource Block (PRB). A PRB has the duration of 1 time slot.
Figure 1: LTE radio frame structure [1]

96
The subcarrier are spaced by 15 KHz from each other. Therefore, each PRB occupies a
bandwidth of 180 KHz (12 x 15 KHz).
The LTE specification define parameters for system bandwidths from 1.25 MHz to 20 MHz
as shown in Table 1.
Table 1: LTE Downlink Parameters
Transmission Bandwidth
(MHz)
1.25 2.5 5 10 15 20
Sub-frame duration (ms) 0.5
Sub-carrier spacing
(KHz)
15
Sampling frequency
(MHz)
1.92 3.84 7.68 15.36 23.04 30.72
FFT size 128 256 512 1024 1536 2048
Number of occupied sub-
carriers
76 151 301 601 901 1201
3. LTE DOWNLINK SYSTEM MODEL
LTE system is basically MIMO-OFDM based system. The system model is given in figure 2.
Figure 2: MIMO-OFDM system [1]
OFDM is employed as multiplexing technique in the LTE system. OFDM consists in dividing
the transmission bandwidth into several orthogonal sub-carriers. The entire set of subcarrier is shared
between different users. The N subcarriers are spaced by 15 KHz. To combat the effect of frequency
selective fading, a cyclic prefix (CP) with the length of LCP is inserted at the beginning of each
OFDM symbol.
Each OFDM symbol is transmitted over frequency selective fading MIMO channels assumed
independents of each other. Each channel is modeled as a Finite Impulse Response (FIR) filter with

97
L taps. After moving the CP and performing the DFT, the received OFDM symbol at one receive
antenna can be written as:
Y = XH + µ (1)
Y represents the received signal vector, X is a matrix which contains the transmitted elements
on its diagonal. H is a channel frequency response, and µ is the noise vector whose entries have the
i.i.d. complex Guassian distribution with zero mean and variance σ2
.
4. CHANNEL ESTIMATION
To estimate the channel, LTE systems use pilot signals called reference signals. When short
CP is used, they are being transmitted during the first and fifth OFDM symbols of every slot. When
long CP is used, they are transmitted during the first and the fourth OFDM symbols.
Figure 3: Downlink reference signal structure on one antenna [2]
From (1), the received pilot signals can be written as:
YP = XP HP + µP (2)
(.)P denotes positions where reference signals are transmitted.
In this paper, we study the performance of LS and LMMSE channel estimation techniques.
4.1 Least Square LS
The main purpose of the channel least square estimator is to minimize the square distance
between the received signals and the original signal.
The least square estimate (LS) of the channel at the pilot subcarrier given in (2) can be
obtained by the following equation [3].
Hp
LS
= (XP)-1
YP (3)
4.2 Linear Minimum Mean Square Error LMMSE
The LMMSE channel estimator is designed to minimize the estimation MSE. The LMMSE
estimate of the channel responses given in (2) is:
Hp
LMMSE
= RHHP (RHPHP + σ2
(XXH
)-1
) HpLS
(4)

International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976
6464(Print), ISSN 0976 – 6472(Online), Volume 5, Issue 3,
RHHP represents the cross correlation matrix
reference signals. RHPHP represents the autocorrelation matrix of the subcarrier with reference
signals. The high complexity of LMMSE estimator (4) is due to the inversion matrix. Every time
data changes, inversion is needed. The complexity of this estimator can be reduced by averaging the
transmitted data. Therefore, we replace the term (XX
The simplified LMMSE estimator becomes:
Hp
LMMSE
= RHHP
Where β is scaling factor which depend on the signal constellation. SNR is the average signal
to noise ratio, and IP is identity matrix.
4.3 Hybrid LS-LMMSE Channel estimation technique
For LTE Downlink systems, the performance of LS and LMMSE channel estimation
techniques under the channel length effect was studied in [
shows that, in the case where CP is longer than the channel length, the LMMSE gives better
performance than LS but at cost of complexity. In the other case, where CP is shorter than the
channel length, LMMSE shows also better performance but only at low SNR
values, LS gives better performance than LMMSE.
So that we propose hybrid LS
channel length effect. In this hybrid system, when CP is equal to or longer than the channel lengt
the hybrid LS-LMMSE algorithm will apply directly the LMMSE channel estimation technique. In
other hand, when CP is shorter than channel length, the hybrid algorithm will act depending on
received SNR value. When received SNR value is low, this algorith
estimation technique and when SNR value is high, hybrid algorithm will switch to LS estimation.
Figure 4: Hybrid LS
International Journal of Electronics and Communication Engineering & Technology (IJECET), ISSN 0976
6472(Online), Volume 5, Issue 3, March (2014), pp. 94-101 © IAEME
98
correlation matrix between all subcarrier and the subcarrier with
represents the autocorrelation matrix of the subcarrier with reference
rsion is needed. The complexity of this estimator can be reduced by averaging the
transmitted data. Therefore, we replace the term (XXH
)-1
in (4) with its expectation E[(XX
The simplified LMMSE estimator becomes:[3]
HHP [RHPHP + (β/SNR)IP]-1
Hp
LS
is scaling factor which depend on the signal constellation. SNR is the average signal
is identity matrix.[3]
LMMSE Channel estimation technique
techniques under the channel length effect was studied in [2][3]. In that paper, the simulation results
hows that, in the case where CP is longer than the channel length, the LMMSE gives better
channel length, LMMSE shows also better performance but only at low SNR value. For higher SNR
values, LS gives better performance than LMMSE.
So that we propose hybrid LS-LMMSE channel estimation technique which is robust to the
channel length effect. In this hybrid system, when CP is equal to or longer than the channel lengt
LMMSE algorithm will apply directly the LMMSE channel estimation technique. In
received SNR value. When received SNR value is low, this algorithm will apply LMMSE channel
Hybrid LS-LMMSE channel estimation algorithm [3]
© IAEME
between all subcarrier and the subcarrier with
represents the autocorrelation matrix of the subcarrier with reference
rsion is needed. The complexity of this estimator can be reduced by averaging the
E[(XXH
)-1
].
(5)
is scaling factor which depend on the signal constellation. SNR is the average signal
. In that paper, the simulation results
hows that, in the case where CP is longer than the channel length, the LMMSE gives better
value. For higher SNR
channel estimation technique which is robust to the
channel length effect. In this hybrid system, when CP is equal to or longer than the channel length,
LMMSE algorithm will apply directly the LMMSE channel estimation technique. In
m will apply LMMSE channel

99
5. SIMULATION RESULTS
In this section, we investigates the performance of hybrid LS -LMMSE estimation techniques
for 2x2 LTE Downlink system under the effect of the channel length. The transmitted signals are
quadrature phase-shift keying (QPSK) modulated. The number of subcarrier in each OFDM symbol
is N = 300, and the length of CP is LCP = 36. 100 LTE radio frames are sent through a frequency-
selective channel. The frequency selective fading channel responses are randomly generated with a
Rayleigh probability distribution. Table 2 gives a summary of simulation parameters.
Table 2: Simulation Parameter.
LTE Bandwidth 5 MHz
No of used subcarrier 300
Cyclic prefix length 36
No of transmitted frames 100
No of transmitted antenna 2
No of received antenna 2
Modulation scheme QPSK
Channel model Rayleigh
5.1 Case with L ≤ LCP
In this case, the cyclic prefix is longer than the channel length. So that, ISI and ICI are
completely suppressed. The hybrid LS-LMMSE estimation will apply directly the LMMSE
estimation technique. Simulation results shows that the LMMSE estimator gives better result than LS
but at cost of complexity. Figure 5 and Figure 6 show respectively the performance of LS, LMMSE
and hybrid estimator in terms of BER and MSE for L = 10.
Figure 5: BER versus SNR for L=10 Figure 6: MSE versus SNR for L=10
5.2 Case with L > LCP
In this case, the cyclic prefix is shorter than the channel length which shows the true
efficiency for the performance of LTE Downlink system. In this case, some unforeseen behavior of
the channel can occur. That will cause the introduction of ISI and ICI. Figure 7 and Figure 8 show
the performance of LMMSE and Hybrid estimator in terms of BER and MSE respectively for L=46.
0 5 10 15 20 25 30
10
-6
10
-5
10
-4
10
-3
10
-2
10
-1
10
0
SNR(dB)
BER
BER performance using LS-LMMSE and hybrid techniques
LS-10
LMMSE-10
Hybrid-10
0 5 10 15 20 25 30 35
10
-4
10
-3
10
-2
10
-1
10
0
SNR(dB)
MSE
MSE performance using LS-LMMSE and hybrid techniques
LS-10
LMMSE-10
Hybrid-10

100
Figure 7: BER versus SNR for L=46 Figure 8: BER versus SNR for L=46
Simulation results show that the Hybrid LS-LMMSE estimator performs better than LMMSE
estimator specially for high SNR range. For this range of SNR values, simulation results show large
difference between two estimators and this proves well the efficiency of the proposed technique.
6. CONCLUSION
Channel estimation is a challenging problem in wireless system. In this paper, we evaluate
the performance of Hybrid LS-LMMSE estimation techniques for LTE Downlink systems under the
effect of the channel length. The cyclic prefix inserted at the beginning of each OFDM symbol is
usually equal to or longer than the channel length in order to suppress ISI and ICI. Simulation results
for LS and LMMSE techniques show that the LMMSE gives better performance than LS in case
where CP is longer or equal to the channel length at cost of complexity. In the other case, where CP
is shorter than the channel length, LMMSE gives better result only for low SNR value. For high SNR
value, LS performs better than LMMSE estimator. In this paper, we compare the simulation results
for both the hybrid and Non-hybrid system. Simulation results for the proposed hybrid system have
shown the efficiency of hybrid technique and specially for the case where the channel length exceed
the cyclic prefix length. In this paper, the hybrid technique applies LMMSE estimator for low SNR
value. For high SNR value, the proposed technique applies LS estimator.
REFERENCES
[1] Hlaing Minn and Vijay K.Bhargava, “An investigation into Time-domain approach for
OFDM channel estimation”, IEEE Transcations on Broadcasting, Vol. 46, No. 4, December
2000.
[2] Md. Jobayer Alam and Shaha Mohammed Goni Abed Sujan, “Low Complexity Channel
Estimation for OFDM systems Based on LS and MMSE Estimators” Blekinge Institute of
Technology, September 2010.
[3] A. Khlifi and R. Bouallegue, “Performance Analysis of LS and LMMSE Channel estimation
techniques for LTE Downlink system ” International journal of Wireless & Mobile Networks
(IJWMN) Vol. 3, No. 5, October 2011.
[4] Helmut Bolcskei and Eth Zurich, “MIMO-OFDM Wireless Systems: Basics, Perspective, and
Challenges” IEEE Wireless Communication, August 2006.
0 5 10 15 20 25 30 35
10
-3
10
-2
10
-1
10
0
SNR(dB)
BER
BER performance using LMMSE and hybrid techniques
LMMSE-46
Hybrid-46
0 5 10 15 20 25 30 35
10
-3
10
-2
10
-1
10
0
SNR(dB)
MSE
MSE performance using LMMSE and hybrid techniques
LMMSE-46
Hybrid-46

101
[5] Asad Mehmood and Waqas Aslam Cheema, “Channel Estimation for LTE Downlink”,
Blekinge Institute of Technology, pp. 11-35, September 2009.
[6] Sajjad Ahmed Ghauri, Sheraz Alam, M. Farhan Sohail, AsadAli, Faizan Saleem,
“Implementation of OFDM and Channel Estimation using LS and MMSE Estimator”,
International journal of Computer and Electronics Research (IJCER), Vol. 2, Issue 1,
February 2013.
[7] A. J. Paulraj, D. A. Gore, R. U. Nabar, and H. Bolcskei, “An overview of MIMO
Communication- A key to gigabit wireless,” Proc. IEEE, Vol. 92, no. 2, pp. 198-218, Feb.
2004.
[8] Ming Jiang and Lajos Hanzo, “Multiuser MIMO-OFDM for Next-Generation Wireless
Systems,” Proc. IEEE, Vol. 95, no. 7, July 2007.
[9] Prof. A.K. Jaiswal, Er. Anil Kumar and Anand Prakash Singh, “Performance Analysis of
MIMO-OFDM Systems in Rayleigh fading Channel,” International Journal of Scientific and
Research Publication, Vol. 2, May 2012.
[10] Lavish Kansal, Ankush Kansal and Kabir Singh, “Performance Analysis of MIMO-OFDM
System using QOSTBC code Structure for M-PSK,” Signal Processing: An International
Journal (SPIJ), Vol. 5, 2011.
[11] Nidhi Mehta, Mandeep Kaur Sekhon and Gurpadam Singh, “Performance Evaluation of
STBC Codes with Channel Estimation by Optimized Pilot Bits”, International Journal of
Electronics and Communication Engineering & Technology (IJECET), Volume 3, Issue 1,
2012, pp. 54 - 61, ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.
[12] Prathima Boppana and M. Shiva Prasad, “Design of Pilot-Symbol Assisted Power
Delay Profile Estimation for MIMO-OFDM Systems”, International Journal of Electrical
Engineering & Technology (IJEET), Volume 4, Issue 5, 2013, pp. 36 - 46, ISSN Print:
0976-6545, ISSN Online: 0976-6553.
[13] Jaimin K. Raval, Prof. Vijay K. Patel and Dr. D. J. Shah, “Research on Pilot Based Channel
Estimation for LTE Downlink using LS and LMMSE Technique”, International Journal of
Electronics and Communication Engineering & Technology (IJECET), Volume 4, Issue 3,
2013, pp. 70 - 82, ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.

40120140503012

More Related Content

What's hot

Viewers also liked

Similar to 40120140503012

More from IAEME Publication

Recently uploaded

40120140503012