A Three Phase D-STATCOM to Compensate AC and DC loads by using Fuzzy Logic DC Link Voltage Controller

75 International Journal for Modern Trends in Science and Technology
Volume: 2 | Issue: 06 | June 2016 | ISSN: 2455-3778IJMTST
A Three Phase D-STATCOM to Compensate
AC and DC loads by using Fuzzy Logic DC
Link Voltage Controller
Kolli Nageswar Rao1
| B. Teja2
1Asst. Professor, Department of EEE, Sree Vahini Institute of Science and Technology, Tiruvuru, India.
2Lecture, Department of EEE, Sree Vahini Institute of Science and Technology, Tiruvuru, India.
A Fuzzy Logic control the transient response of the distribution static compensator (D-STATCOM) is very
important while compensating rapidly varying unbalanced and nonlinear loads. Any change in the load
affects the dc-link voltage directly. The sudden removal of load would result in an increase in the dc-link
voltage above the reference value; where as a sudden increase in load would reduce the dc-link voltage
below its reference value. The proper operation of D-STATCOM requires variation of the dc-link voltage within
the prescribed limits. Conventionally, a proportional integral (PI) controller is used to maintain the dc-link
voltage to the reference value. A Fuzzy Logic controls the transient response of the distribution static
compensator (D-STATCOM) is very important while compensating rapidly varying unbalanced and nonlinear
loads. It uses deviation of the capacitor voltage from its reference value as its input. However, the transient
response of the conventional PI dc-link voltage controller is slow. In this paper, a fast-acting dc-link voltage
controller based on the energy of a dc-link capacitor is proposed. Mathematical equations are given to
compute the gains of the conventional controller based on fast-acting dc-link voltage controllers to achieve
similar fast transient response. The detailed simulation and experimental studies are carried out to validate
the proposed controller.
KEYWORDS: DC-Link voltage Controller, distribution static compensator (DSTATCOM), fast transient
response, harmonics, load compensation, power factor, power quality (PQ), un balance, voltage-source
inverter (VSI)
Copyright © 2016 International Journal for Modern Trends in Science and Technology
All rights reserved.
I. INTRODUCTION
The proliferation of power-electronics-based
equipment, nonlinear and unbalanced loads, has
aggravated the power-quality (PQ) problems in the
power distribution net-work. They cause excessive
neutral currents, overheating of electrical
apparatus, poor power factor, voltage distortion,
high levels of neutral-to-ground voltage, and
interference with communication systems [1], [2].
The literature records the evolution of different
custom power devices to mitigate the above
power-quality problems by injecting
voltages/currents or both into the system [3]–[6].
The shunt-connected custom power device, called
the distribution static compensator (DSTATCOM),
injects current at the point of common coupling
(PCC) so that harmonic filtering, power factor
correction, and load balancing can be achieved.
The DSTATCOM consists of a current-controlled
voltage-source inverter (VSI) which injects current
at the PCC through the interface inductor. The
operation of VSI is sup-ported by a dc storage
capacitor with proper dc voltage across it. In some
of the electric power consumers, such as the
telecommunications industry, power-electronics
drive applications, etc., switch-mode rectifiers to
support dc bus voltage. Such an arrangement
draws nonlinear load currents from the utility. This
causes poor power factor and, hence, more losses
and less efficiency. Clearly, there are PQ issues,
such as unbalance, poor power factor, and
harmonics produced by telecom equipment in
power distribution networks. Therefore, the
functionalities of the conventional DSTATCOM
should be increased to mitigate the aforementioned
PQ problems and to supply the dc loads from its dc
link as well. The load sharing by the ac and dc bus
depends upon the design and the rating of the VSI.
ABSTRACT

A Three Phase D-STATCOM to Compensate AC and DC loads by using Fuzzy Logic DC Link Voltage Controller
This DSTATCOM differs from conventional one in
the sense that its dc link not only supports
instantaneous compensation but also supplies dc
loads. However, when the dc link of the
DSTATCOM supplies the dc load as well, the
corresponding dc power is comparable to the
average load power and, hence, plays a major role
in the transient response of the compensator.
Hence, there are two important issues. The first
one is the regulation of the dc-link voltage within
prescribed limits under transient load conditions.
The second one is the settling time of the dc–link
voltage controller. Conventionally, a PI controller is
used to maintain the dc-link voltage. It uses the
deviation of the capacitor voltage from its reference
value as its input. However, the transient response
of the conventional dc-link voltage controllers is
slow, especially in applications where the load
changes rapidly. Some work related to dc-link
voltage controllers and their stability is reported in
[15].
However, the work is limited to rectifier units
where switching patterns are well defined and
analysis can be easily carried out. In this paper, a
fast-acting dc-link voltage controller based on the
dc-link capacitor energy is proposed. The detailed
modeling, simulation, and experimental
verifications are given to prove the efficacy of this
fast-acting dc-link voltage controller. There is no
systematic procedure to design the gains of the
conventional PI controller used to regulate the dc
link voltage of the DSTATCOM. Herewith,
mathematical equations are given to design the
gains of the conventional controller based on the
fast-acting dc-link voltage controllers to achieve
similar fast transient response.
II. D-STATCOM FOR COMPENSATING AC AND DC
LOADS
Various VSI topologies are described in the
literature for realizing DSTATCOM to compensate
unbalanced and nonlinear loads [21]–[29]. Due to
the simplicity, the absence of unbalance in the
dc-link voltage and independent current tracking
with respect to other phases, a three-phase
H-bridge VSI topology is chosen. Fig. 1 shows a
three-phase, four-wire-compensated system using
an H-bridge VSI topology-based DSTATCOM
compensating unbalanced and nonlinear ac load.
Fig.1Three-phase, four-wire compensated system using the
H-bridge VSI topology-based DSTATCOM
In addition to this, a dc load is connected (𝑅 𝑑𝑐 ) is
connected across the dc link. The DSTATCOM
consists of 12 insulated-gate bipolar transistor
(IGBT) switches each with an anti parallel diode, dc
storage capacitor, three isolation transformers,
and three interface inductors. The star point of the
isolation transformers ( 𝑛′
) is connected to the
neutral of load (𝑛) and source (N). The H-bridge
VSIs are connected to the PCC through interface
inductors. The isolation transformers prevent a
short circuit of the dc capacitor for various
combinations of the switching states of the VSI.
The inductance and resistance of the isolation
transformers are also included in 𝐿𝑓 and 𝑅𝑓 the
source voltages are assumed to be balanced and
sinusoidal. With the supply being considered as a
stiff source, the feeder impedance (𝐿 𝑠, 𝑅𝑠) shown in
Fig. 1 is negligible and, hence, it is not accounted
in state-space modeling. To track the desired
compensator currents, the VSIs operate under the
hysteresis band current control mode due to their
simplicity, fast response, and being independent of
the load parameters [30]. The DSTATCOM injects
currents into the PCC in such a way as to cancel
unbalance and harmonics in the load currents. The
VSI operation is supported by the dc storage
capacitor with voltage across it. The dc bus voltage
has two functions, that is, to support the
compensator operation and to supply dc load.
While compensating, the DSTATCOM maintains
the balanced sinusoidal source currents with unity
power factor and supplies the dc load through its
dc bus.
III. DC-LINK VOLTAGE CONTROLLERS
As mentioned before, the source supplies an
unbalanced nonlinear ac load directly and a dc
load through the dc link of the D-STATCOM, as
shown in Fig. Due to transients on the load side,
the dc bus voltage is significantly affected. To

regulate this dc-link voltage, closed-loop
controllers are used. The proportional-
integral-derivative (PID) control provides a generic
and efficient solution to many control problems.
The control signal from PID controller to regulate
dc link voltage is expressed as
𝑉𝐶 = 𝐾𝑝 𝑉𝑑𝑐𝑟𝑒𝑓 − 𝑉𝑑𝑐 + 𝐾𝑖 𝑉𝑑𝑐𝑟𝑒𝑓 − 𝑉𝑑𝑐 𝑑𝑡 +
𝐾𝑑
𝑑(𝑉 𝑑𝑐𝑟𝑒𝑓 −𝑉 𝑑𝑐 )
𝑑𝑡
………… (1)
𝐾𝑃 , 𝐾𝑑 and 𝐾𝑖 are proportional, integral, and
derivative gains of the PID controller, respectively.
The proportional term provides overall control
action proportional to the error signal. An increase
in proportional controller gain 𝐾𝑃 reduces rise time
and steady-state error but increases the overshoot
and settling time. An increase in integral gain 𝐾𝑖
reduces steady state error but increases overshoot
and settling time. Increasing derivative gain 𝐾𝑑 will
lead to improved stability. However, practitioners
have often found that the derivative term can
behave against anticipatory action in case of
transport delay. A cumbersome trial-and-error
method to tune its parameters made many
practitioners switch off or even exclude the
derivative term. Therefore, the description of
conventional and the proposed fast-acting dc-link
voltage controllers using PI controllers are given in
the following subsections.
i. Conventional DC-link voltage controller:
The conventional PI controller used for
maintaining the dc-link voltage is shown in Fig. 2.
To maintain the dc-link voltage at the reference
value, the dc-link capacitor needs a certain amount
of real power, which is proportional to the
difference between the actual and reference
voltages. The power required by the capacitor can
be expressed as follows
𝑃𝐷𝐶 = 𝐾𝑝 𝑉𝑑𝑐𝑟𝑒𝑓 − 𝑉𝑑𝑐 + 𝐾𝑖 𝑉𝑑𝑐𝑟𝑒𝑓 − 𝑉𝑑𝑐 𝑑𝑡
Fig. 3 Schematic diagram of the conventional dc-link
voltage controller.
Fig. 4 Schematic diagram of the fast-acting dc-link voltage
controller
The dc-link capacitor has slow dynamics
compared to the compensator, since the capacitor
voltage is sampled at every zero crossing of phase
supply voltage. The sampling can also be
performed at a quarter cycles depending upon the
symmetry of the dc-link voltage waveform. The
drawback of this conventional controller is that its
transient response is slow, especially for
fast-changing loads. Also, the design of PI
controller parameters is quite difficult for a
complex system and, hence, these parameters are
chosen by trial and error. Moreover, the dynamic
response during the transients is totally dependent
on the values of 𝐾𝑃 𝑎𝑛𝑑 𝐾𝑖 when is comparable
to 𝑃𝑙𝑎𝑣𝑔 .
ii. Fast-Acting DC Link Voltage Controller
To overcome the disadvantages of the
aforementioned controller, an energy-based dc-link
voltage controller is proposed. The energy required
by the dc-link capacitor Wdc to charge from actual
voltage Vdc to the reference value Vdcref can be
computed as
𝑊𝑑𝑐 =
1
2
𝐶 𝑑𝑐 (𝑉𝑑𝑐𝑟𝑒𝑓
2
− 𝑣 𝑑𝑐 ) ……… (2)
In general, the dc-link capacitor voltage has
ripples with double frequency, that of the supply
frequency. The dc power P’
dc required by the dc-link
capacitor is given as
𝑃𝑑𝑐 =
𝑊 𝑑𝑐
𝑇𝑐
=
1
2𝑇𝑐
(𝑉𝑑𝑐𝑟𝑒𝑓
2
− 𝑣 𝑑𝑐
2
) …………. (3)
Where 𝑇𝐶 is the ripple period of the dc-link
capacitor voltage. Some control schemes have been
reported in [33] and [34]. However, due to the lack
of integral term, there is a steady-state error while
compensating the combined ac and dc loads. This
is eliminated by including an integral term. The
input to this controller is the error between the
squares of reference and the actual capacitor
voltages.
Fig. 5 Schematic diagram of the fast-acting dc-link voltage
controller
This controller is shown in Fig. 5 and the
total dc power required by the dc-link capacitor is
computed as follows:
𝑃𝐷𝐶 = 𝐾𝑝 𝑉𝑑𝑐𝑟𝑒𝑓 − 𝑉𝑑𝑐 + 𝐾𝑖 𝑉𝑑𝑐𝑟𝑒𝑓 − 𝑉𝑑𝑐 𝑑𝑡
The coefficients 𝐾𝑝𝑒 and 𝐾𝑖𝑒 are the
proportional and integral gains of the proposed
energy-based dc-link voltage controller. As an
energy-based controller, it gives fast response
compared to the conventional PI controller. Thus, it

can be called a fast acting dc-link voltage
controller. The case in the calculation of the
proportional and integral gains is an additional
advantage.
iii. Selection of the DC-link capacitor
The value of the dc-link capacitor can be selected
based on its ability to regulate the voltage under
transient conditions. Let us assume that the
compensator in first Fig. 1 is connected to a system
with the rating of X kilovolt amperes. The energy of
the system is given by 𝑋 ∗ 1000 𝐽/𝑠. Let us further
assume that the compensator deals with half (i.e.,
𝑋
2
)
and twice (i.e.,2𝑋) capacity under the transient
conditions for n cycles with the system voltage
period of 𝑇𝑆. Then, the change in energy to be dealt
with by the DC capacitor is given as
Now this change in energy (21) should be
supported by the energy stored in the dc capacitor.
Let us allow the dc capacitor to change its total
dc-link voltage from 1.4 𝑉𝑚 to 1.8 𝑉𝑚 during the
transient conditions where 𝑉𝑚 is the peak value of
phase voltage. Hence, we can write
IV. SIMULATION RESULTS
The load compensator with H-bridge VSI
topology as shown in Fig is realized by digital
simulation by using MATLAB. The load and the
compensator are connected at the PCC. The ac load
consists of a three-phase unbalanced load and a
three-phase diode bridge rectifier feeding a highly
inductive R-L load. A dc load is realized by an
equivalent resistance Rdc as shown in the figure.
The dc load forms 50% of the total power
requirement. The system and compensator
parameters are given in Table.1 By monitoring the
load currents and PCC voltages, the average load
power is computed. At every zero crossing of phase
a voltage, Pdc is generated by using the dc-link
voltage controller. The state-space equations are
solved to compute the actual compensator currents
and dc-link voltage. These actual currents are
compared with the reference currents given by
using hysteresis current control. Based on the
comparison, switching signals are generated to
compute the actual state variables by solving the
state-space model. The source voltages and load
currents are plotted in Fig (a) and (b).
The load currents have total harmonic
distortions of 8.9%, 14.3%, and 21.5% in phases a,
b and c, respectively. The unbalance in load
currents results in neutral current as illustrated in
the figure. The compensator currents and
compensated source currents are shown in Fig. (c)
and (d). As seen from Fig. (d), the source currents
are balanced sinusoids; however, the switching
frequency components are superimposed over the
reference currents due to the switching action of
the VSI. The currents have a unity power factor
relationship with the voltages in the respective
phases. The THDs in these currents are 3.6%,
3.7%, and 3.9% in phases a, b and c, respectively
Fig .6: (a) Supply voltages. (b) Load currents. (c)
Compensator currents (d) Compensated source currents.
There are notches in the source currents due to
finite bandwidth of the VSI. The transient

performance of the conventional and fast-acting
dc-link voltage controllers are studied by making
sudden changes in the ac load supplied by the ac
load bus as well as the dc load supplied by the dc
link. In the simulation study, the load is halved at
the instant t=0.4 s and brought back to full load at
t=0.8 s. The transient performance is explained in
the following subsections.
i. Transient Performance of Conventional
DC-Link Voltage Controller
The conventional dc-link voltage controller is
used to generate the dc load power 𝑃𝐷𝐶 which is
inclusive of losses in the inverter. The transient
performance of the compensator is shown in Fig. 7
(a) and (b).
Fig. 7: Transient response of the conventional controller. (a)
Compensated source current in phase A (b) DC-link voltage.
The total load, which is a combination of linear
unbalanced and nonlinear load (as given in Table),
is halved at the instant t=0.4 s. Due to a sudden
reduction in the load, the dc-link capacitor absorbs
surplus power from the source. Therefore, there is
an increase in dc-link capacitor voltage above the
reference value. Based on the values of PI controller
gains, the dc-link capacitor voltage controller will
be brought back to the reference value after a few
cycles.
Similarly, when the load is switched back to the
full load at instant t=0.8 s, the dc capacitor
supplies power to the load momentarily and,
hence, the dc-link voltage falls below the reference
value. Due to the PI controller action, the capacitor
voltage will gradually build up and reach its
reference value. If gains of the conventional dc-link
voltage controller are not properly chosen, the
dc-link voltage would have undesirable overshoot
and considerably large settling time. Consequently,
the performance of the load connected to the dc
link also gets affected due to the above factors. It
can be observed from Fig.7 (a) and (b) that the
conventional dc-link voltage controller takes about
a ten cycle period to reach the reference voltage
during load transient. This is indicated by time
duration ts in these figures.
ii. Transient Response of the Conventional
fuzzy logic Controller
By using the fuzzy logic controller instead of the
PI controller we will get the better transient
response. The load is halved at t=0.4s .so the
dc-link voltage is suddenly increased above the
reference value .And it is brought back to its
reference value due to the fuzzy controller action at
the instant of t=0.42s as shown in the Fig.10.and
when the load is switched back to the full load at
instant t =0.8 s, the dc capacitor supplies power to
the load. Hence dc-link voltage is falls below the
reference value and it is brought back to the
reference value at t=0.82s as shown in the Fig. 8.
Fig. 8: Transient response of the fast acting fuzzy logic
controller
V. CONCLUSION
A VSI topology for DSTATCOM compensating ac
unbalanced and nonlinear loads and a dc load
supplied by the dc link of the compensator is
presented. The state-space modeling of the
DSTATCOM is discussed for carrying out the
simulation studies. An energy-based fast-acting
dc-link voltage controller is suggested to ensure the
fast transient response of the compensator.
Mathematical equations are developed to compute

the gains of this controller. The efficacy of the
proposed controller over the conventional dc-link
voltage controller is established through the digital
simulation and experimental studies. It is observed
from these studies that the proposed dc-link
voltage controller gives fast transient response
under load transients. By using fuzzy logic
controller instead of these two controllers the
transient response is very fast. The conventional
fuzzy logic controller gives the better transient
response than that of the conventional PI
controller. The fast acting fuzzy logic controller
gives the fast transient response than that of all
previous controllers which are discussed above.
The efficacy of the proposed controller is
established through a digital simulation. It is
observed from the above studies the proposed fast
acting fuzzy logic controller gives the fast transient
response for fast varying loads.
VI. APPENDIX
Fig. 9 Conventional Fuzzy logic control of three-phase
D-STATCOM
Fig. 10 Conventional diagram of three-phase D-STATCOM
Fig. 11 Proposed model of three-phase DSTATCOM with fast
acting fuzzy logic controller
Table 1 EXPERIMENTALPARAMETERS
REFERENCES
[1] Mahesh K.mishra member IEEE and K.karthikayan
“A fast acting dc-link voltage controller for three
phase dstatcom to compensate ac and dc loads”
IEEE Transctions on power delivery, vol., 24,no.4,
October 2009
[2] M. H. J. Bollen, Understanding Power Quality
Problems: Voltage Sags and Interruptions. New York:
IEEE Press, 1999.
[3] W. M. Grady and S. Santoso, Proc. IEEE Power Eng.
Rev. Understanding Power System Harmonics, vol.
21, no. 11, pp. 8–11,2001.
[4] N. Hingorani, “Introducing custom power,” IEEE
Spectr., vol.32,no.6,pp.41–8,Jun.1995.
[5] V. Dinavahi, R. Iravani, and R. Bonert, “Design of a
real-time digital simulator for a DSTATCOM system,”
IEEE Trans. Ind. Electron., vol.51, no. 5, pp.
1001–1008, Oct. 2004.
[6] M.K.Mishra,A. Ghosh, and A. Joshi, “A new
STATCOM topology to compensate loads containing
ac and dc components,” in Proc. IEEE Power Eng.
Soc. Winter Meeting, Singapore, Jan. 23–27, 2000,
vol. 4, pp. 2636–2641.

[7] A. Nabae, I. Takahashi, and H. Akagi, “A new
neutral-point-clamped PWM inverter,” IEEE Trans.
Ind. Appl., vol. IA-17, no. 5, pp. 518–523, Sep. 1981.
[8] M. Aredes, J. Häfner, and K. Heumann,
“Three-phase four-wire shunt active filter control
strategies,” IEEE Trans. Power Electron., vol. 12, no.
2, pp. 311–318, Mar. 1997.
[9] B. Singh, K. Al-Hadded, and A. Chandra, “A review of
active filters for power quality improvements,” IEEE
Trans. Ind. Electron., vol. 46, no. 5, pp. 960–971,
Oct. 1999.
[10]M. El-Habrouk, M. K. Darwish, and P. Mehta, “Active
power filters: A review,” Proc. Inst. Elect. Eng., Electr.
Power Appl., vol. 147, no. 5, pp. 403–413, Sep. 2000.
[11]A. S. Kislovski, “Telecom power-supply plants using
three-phase rectifiersand active filters,” in Proc. 2nd
Int. Telecommunications EnergySpecial Conf.,
Budapest, Hungary, Apr. 22–24, 1997, pp. 127–13
4.
[12]A. Prodic´ and G. D. Marques, “Compensator design
and stability assessment for fast voltage loops of
power factor correction rectifiers,”IEEE Trans. Power
Electron., vol. 22, no. 5, pp. 1719–1730, Sep. 2007.
[13]D. Zhao and R. Ayyanar, “Space vector PWM with DC
link voltage control and using sequences with active
state division,” in Proc., IEEE Int. Symp. Industrial
Electronics, Montreal, QC, Canada, Jul. 9–12, 2006,
vol. 2, pp. 1223–1228.
[14]P.Hoang, K.Tomosovic, “Design and an analysis an
adaptive fuzzy power system stabilizer”, Vol. 11, No.
2.June 1996;
[15]WenxinLiu, Ganesh K.Venayagamoorthy,
DonaldC.wunseh. Adaptive neural network based
power system stabilizer design, IEEE 2003 ,
page2970-2975.
BIOGRAPHIES
Kolli Nageswara Rao was born in 1986. He
graduated from Jawaharlal Nehru
Technological University, Hyderabad in the
year 2009. He received M.Tech degree from
Jawaharlal Nehru Technological University,
Hyderabad in the year 2013. He is working
as Asst. Professor in Sree Vahini Institute of
Science & Technology, Tiruvuru. Andhra
Pradesh. His research interests include
power electronics, multilevel converters, FACTS, PWM
techniques and electric machinery analysis.
Boggavarapu Teja was born in 1992. He
graduated from Jawaharlal Nehru
Technological University, Kakinada in the year
2014. He is working as Lecturer in Sree Vahini
Institute of Science & Technology, Tiruvuru.
Andhra Pradesh. His research interests FACTS,
PWM techniques

A Three Phase D-STATCOM to Compensate AC and DC loads by using Fuzzy Logic DC Link Voltage Controller

More Related Content

What's hot (18)

Viewers also liked (20)

Similar to A Three Phase D-STATCOM to Compensate AC and DC loads by using Fuzzy Logic DC Link Voltage Controller (20)

Recently uploaded (20)

A Three Phase D-STATCOM to Compensate AC and DC loads by using Fuzzy Logic DC Link Voltage Controller