chapter 5 (1).pptx

Course outcome
C403.4: Identify and select various electrical
machines based on their characteristics and
applications.

Introduction
• The induction motors are basically ac motors.
• They can operate on either single phase or three
phase ac supply, however the single phase
induction motors are suitable only for few
applications.
• In almost 85% applications the three phase
induction motors are preferred.
• Depending on the type of rotor, the induction
motor are classified into two types, slip ring
induction motors and squirrel cage induction
motors.

• Advantages of induction motors over DC motors:
1. Low maintenance requirement.
2. Ruggedness, smaller size and weight.
3. Low cost.
4. They can operate in dusty and explosive environment.
5. They can operate at much higher speed.
6. It can produce sufficient torque.
7. Speed control by using thyristors can give a wide
range of speeds.

• Disadvantages of induction motors:
1. The efficiency of induction motors varies
with speed.
2. They have low starting torque.
3. They have a lagging and low power factor.
4. Speed control by electrical methods is not
easy.

• Applications of induction motors:
1. Fans
2. Pumps
3. Extruders
4. Conveyors
5. In food and chemical industries
6. Paper and sugar industries etc.
7. Chemical, textile, mines and traction etc.

Rotating Magnetic Field (RMF)
• The induction motor operates on the principle of
rotating magnetic field(RMF) which is produced
by the stator winding of the induction motor in the
air gap between the stator and the rotor.
• The stator is a three phase stationary winding
which can be either star connected or delta
connected.
• Whenever the ac supply is connected to stator
winding, line current IR, IY and IB start flowing
and these line currents are 1200 phase shifted with
respect to each other.

• Due to each line current a sinusoidal flux is produced in
the air gap. These fluxes have the same frequency as
that of line currents and they are also 1200 phase
shifted with respect to each other.
• Let the flux produced by line current IR be øR, that
produced by IY be øY and that produced by IB be øB.
• Mathematically
øR = øm sin ωt
øY = øm sin (ωt-1200)
øB = øm sin (ωt-2400)

1. Production of RMF:
• The effective or total flux (øT) in the air gap
between the stator and rotor is equal to the
phasor sum of the three component fluxes øR, øY
and øB .
∴ øT = øR + øY + øB
• The magnitude of øT at any value of θ from 00 to
3600 is constant.
• øT rotates in the clockwise direction in space.
One rotation of øT corresponding to one cycle.

2. Speed of RMF:
• The RMF rotates at a speed called
synchronous speed Ns which is given by,
Ns = 120 f1 / P RPM
where f1 = frequency of stator supply
P = Number of poles of the motor.

3. Direction of RMF :
• The direction of RMF depends on the
sequence of the ac supply being connected to
the stator winding.
• RMF rotates in the clockwise direction if the
phase sequence is R, Y, B.
• But if the sequence is changed, the direction of
RMF will reverse.

Construction of Induction Motor
• An induction motor consists of two main parts:
1. Stator 2. Rotor
• The stationary frame called stator and the rotating
armature called rotor.
• Fig.(1) shows the construction of a three phase
induction motor.
• The function of various parts is as follows:
1. Frame: It provides the mechanical support to entire
construction. It contains the stator winding.
2. Air gap: Air gap provides the space for the rotating
magnetic field between stator and rotor.

3. Fan: The fan rotates with the rotor. Its function is to
cool down the motor.
4. Slip rings: The rotor winding terminals are
permanently connected to the slip rings. The slip rings
are continuously in contact with three brushes which
are pressed against slip rings. External connections
from brushes are brought out.
• Similar to stator, the rotor drum is provided with slots.
• The stator can be a star connected or delta connected
and connected to the 3 phase ac supply.
• The current flows through the rotor due to the principle
of induction. Hence the name induction motor.

Fig.(1): construction of three phase induction motor

Fig.(2): three phase induction motor

Principle of Operation
• The three phase stator winding of induction motor is connected to
the three ac supply.
• Due to ac voltage applied, current starts flowing in the stator
conductors.
• Due to three phase stator current, a rotating magnetic field (RMF)
of constant amplitude and rotating at a constant speed is set up in
the air gap between stator and rotor.
• The rotor winding is not rotating. So rotating magnetic field cuts
the stationary rotor conductors and induced emf in the rotor
winding.
• The rotor induced voltage gives rise to currents.
• So rotor current will flow in such a direction that the rotor will
experienced a force that accelerates it in same direction as that of
RMF.

Synchronous Speed (Ns)
• The synchronous speed is the speed at which
the rotating magnetic field rotates.
• Ns is dependent only on the stator frequency f1
and number of poles P.
Ns = 120 f1 /P

Slip (s)
• The difference between the synchronous speed
(Ns) and the actual motor speed (N) is
indicated by the slip “s”.
% slip = (Ns – N)/Ns x 100 %
• The actual speed N can be expressed in terms
of s as,
N = Ns (1-s)
• The value of slip will vary between 0 and 1 for
motoring operation.

Torque-speed characteristics
• The torque speed characteristics of induction motor can be divided into
three sections:
1. Forward motoring
2. Plugging
3. Regeneration
• Forward motoring:
 The forward motoring region corresponds to the values of slip
between 0 and 1.
 In this region, the motor rotates in the same direction as that of
rotating magnetic field.
 The torque increases as the slip increases while air gap flux remains
constant.
 Once the torque reaches its maximum value at critical slip sm., the
torque decreases with increase in slip due to reduction in air gap flux.

 The region of (0 < s < sm) is known as the stable region of
operation and the operating point of the motor should be in this
region of the characteristics.
 This is stable region because in this region with increase in the
torque demand, the motor speed decreases.
 The region of (sm < s < 1) is unstable region because in this
region with increase in torque the speed of the motor increases.
• Generating region:
 For the generating region, the slip needs to be negative and in
between 0 and -1.
 The torque produced is in opposite direction to that of the
motoring mode so it is shown to be negative.

• Plugging or counter current braking:
The motor operates in the plugging or counter
current braking mode for values s > 1.
To get values of s > 1, N must be negative i.e.
Ns and N must have opposite directions i.e. the
RMF and rotor should rotate in opposite
directions.
This is achieved by interchanging any two
phases of the stator .

Fig.(1): Speed-Torque characteristics of induction motor

Speed control of Induction motor
• Speed control of induction motor by using variable frequency
drive (VFD):
 We know that the actual speed N is given by,
N = Ns (1 – s)
and Ns = 120 f1 / P
 So we can change the actual speed by changing the synchronous
speed. But synchronous speed is changed by changing the stator
supply frequency f1.
 So theoretically we can control the speed by changing only f1.
 But only change in f1, keeping V1 constant has an adverse effect on
the air gap flux because air gap flux is given by,
øag ∝ (V1 / f1)
 If f1 is reduced by keeping V1 constant then there is a possibility of
core saturation.

Hence the ratio (V1/f1) is kept constant by
changing both the stator voltage V1 and
frequency f1 simultaneously. This is necessary
to keep the air gap flux constant.
Hence this method is called as constant (v/f)
control. It is also known as variable frequency
drive (VFD).
The block diagram of constant (V/f) control is
as shown in fig.(1).

Fig.(1): constant (V/f) control for induction motor

• Operation:
 The ac input of constant voltage and constant frequency
is applied to an AC to DC converter which is a rectifier.
 At the output of AC to DC converter we get a DC
voltage. A capacitor bank is used to reduced the ripple
content in the DC voltage.
 This DC voltage is applied at the input of an inverter.
This inverter converts the DC voltage into a 3 phase
variable voltage variable frequency AC voltage.
 This voltage is applied to the stator winding of the
motor. Thus we get the constant V/f control.

Starter
• The rotor current under running condition is given by,
|I2r| = s E2 / (R2
2 + s2 X2
2)1/2 …..(1)
where E2 = rotor induced emf at stand still. At starting when the
motor is at stand still s = 1.
∴ |I2r| = E2 / (R2
2 + X2
2)1/2 …..(2)
but E2 = (N2/N1) V1, at stand still
∴ E2 = KV1
∴ |I2r| = KV1 / (R2
2 + X2
2)1/2 ……(3)
• From eq.(3), it is clear that rotor current at starting depends on:
1. stator voltage V1 and
2. leakage reactance of rotor (X2).
• If the rated stator voltage is applied to the motor at the time of
starting, the motor will draw heavy starting current.

• This will lead to excess I2R losses in the winding
which will overheat the motor.
• Secondly due to a heavy current drawn from the
ac supply, at the time of starting its supply voltage
will reduced.
• The heavy starting current may damaged the
motor winding as well.
• In order to avoid these problems, we can use
some kind of a starter to limit the starting current
of the induction motor.

1. Star-delta starter:
• Here the stator winding of the motor is connected in
star configuration at the time of starting. This reduces
the voltage across each winding to 1/√3 of the rated
voltage.
• When the motor accelerates, the stator is connected in
delta configuration, to apply the rated voltage to the
winding.
• The starting torque reduced as the torque is
proportional to square of voltage and there is jerk
while switching from star to delta.
• Fig.(1), shows the arrangement for star delta starter.

Start mode:
The 3 pole 6 way switch is kept in the start mode
first. This will connect the R’, B’ and Y’ terminals
of the stator windings to each other. This acts as
the star point.
This supply is connected to R, Y and B terminals
of the stator winding. Thus in the “start” mode the
stator windings are connected to form a star.
Equivalent circuit for the “start” mode is as
shown in fig.(2a).

Run mode:
The 3 pole 6 way switch is thrown into the
“Run” position once the motor accelerates.
This will connect the stator winding in the
following manner,
R B’ , Y R’ and B Y’
This is shown in fig.(2) which illustrates how
the stator winding is connected to form a delta.

(a) In the start mode (b)In the run mode
Fig.(2): equivalent circuits for star delta starter

2. Direct on Line (DOL) starter:
 The DOL starter is as shown in fig.(3).
 It consists of fuse links connected in each line, thermal
overload relay contacts, contactor contacts and start stop
logic in series with each line.
• Operation:
 To start the motor, press the start switch. The stop switch in
series with it is a press to off switch.
 As the start switch is pressed, the contactor coil get
connected across the lines Y and B.
 The armature rod shown by dotted lines is pulled towards
the contactor coil and normally open contacts C1, C2, C3 and
C4 will be closed

 The ac supply is connected to stator winding through
contacts C1, C2 and C3 as shown in fig.(3).
 The additional contact C4 is connected across the start
switch. It keeps the contactor coil energized even after
releasing the start switch.
 If we want to stop the motor, then press stop switch.
 This will disconnect the contactor coil from ac supply,
all contacts are open circuited and the stator
disconnected from the ac supply.
 Same thing will happen if the ac supply fails.
Afterwards when the ac supply is restored, we have to
press the start switch again to start the motor.

Specifications of induction motor
• Important specifications of a 3 phase induction motor are as
follows:
1. Number of phases
2. Stator connection
3. Rotor type
4. frequency
5. Rated stator voltage
6. Base speed RPM
7. Power output kW/HP
8. Insulation
9. Power factor
10. duty

Single Phase Induction Motor
• It is more convenient to use single phase ac motors
instead of d.c. motors. Practically single phase a.c.
motors are used in most of the applications.
• Construction:
 A single phase induction motor has two main parts
namely stator (the one which is stationary) and rotor
(the one which is rotating).
 The stator winding is connected across a single phase
a.c. supply. The ac supply produces a rotating magnetic
field in the airgap between the stator and rotor.

The field rotates at a speed called synchronous
speed and it is denoted by Ns.
The induction motor actually rotates at a speed
which is slightly less than the synchronous
speed.
As shown in fig.(1), the rotor consists of
copper or aluminium bars which are
permanently short circuited at both the ends
using the conducting rings called end rings.

Fig.(1): construction of a squirrel cage rotor

• Principle of operation:
 A single phase ac supply is connected to the stator
winding. This forces an alternating current through the
stator winding. This current produces an alternating
flux in the air gap between stator and rotor.
 The alternating flux passes over the rotor conductors
and induces an emf into it due to transformer action.
 Due to this induced voltage, a current starts flowing
through the rotor conductors. This current will then
produces its own flux called as rotor flux
 The main flux produced by the stator winding interacts
with the rotor flux to produce the torque.

 The rotor flux gets produced due to the principle of induction hence
it is called as induction motor.
 But single phase induction motor are not self starting, like DC
motors.
• Types of single phase induction motor:
 Some of the methods used to make an induction motor self starting.
Based on these techniques, the single phase induction motor are
classified as follows:
1. Split phase induction motor
2. Capacitor start induction motor
3. Capacitor start, capacitor run induction motor
4. Shaded pole induction motor.

Resistive Split Phase Induction
Motor
• The construction of split phase induction
motor is as shown in fig.(1).
• This motor consists of two winding namely the
main winding and the auxillary (starting)
winding.
• The main winding is highly inductive while
starting winding is resistive.

Fig.(1): Split Phase Type Induction Motor

• Principle of operation:
 The current flowing through the main winding (Im) lags behind
the V by 900 since the main winding is highly inductive.
 The current flowing through the starting winding (Ist) is almost in
phase with the supply voltage V as this winding is resistive.
 The fluxes produced due to these currents will be placed 900 with
respect each other. And the resultant of these fluxes will be a
rotating magnetic field. Due to the RMF a non-zero starting
torque acting in one direction will be produced.
 The centrifugal switch connected in series with the starting
winding gets automatically open circuited when the motor speed
reaches about 70% to 80% of the synchronous speed.
 After that the motor rotate only on the main winding. Thus under
the running condition the auxillary winding remains out of the
circuit.

 The direction of rotation of split phase motor can be
reversed by reversing the terminals of either main winding
or starting winding. The direction of rotation changes due to
the reversal in direction of rotating magnetic field.
• Applications:
 The starting torque of this motor is poor. So it is used in
following applications:
1. Fans and blowers
2. Washing machines
3. Centrifugal pumps

Capacitor Start Induction Motor
• The construction of this motor is as shown in fig.(1a).
• As shown in fig, the starting winding connected in series
with the capacitor draws a leading current while the main
winding continues to draw the lagging current.
• Due to this the fluxes produce a rotating magnetic field
which result in the rotation of the motor.
• The current (Im) through the main winding will lag
behi9nd the source voltage as the main winding is
inductive. But the angle (Ist) through the starting winding
leads the supply voltage by some angle due to the
presence of capacitor. Hence the angle between the fluxes
produced by Im and Ist will be large as shown in fig.(1b).

• Due to this large angle, the starting torque
produced by the capacitor start motor produces a
larger starting torque as compared to that
produced by the split phase induction motor.
• As soon as the speed reaches 75% to 80% of the
maximum speed, the centrifugal switch is
automatically open circuited and the starting
winding alongwith the capacitor goes out of the
circuit.
• The induction motor will then be running only on
the flux produced by the main winding.

Fig.(1): Capacitor Start Motor

• Capacitor Start Capacitor Run Motor:
 Fig.(2) shows the construction of capacitor start capacitor
run motor. It shows that there is no centrifugal switch,
hence the capacitor will not go out of the circuit at all.
 The direction reversal for capacitor type motors can be
achieved by interchanging the connection of main and
auxiliary windings.
 This will interchange the fields produced by the two
winding. The interchanged phase shifted fields will reverse
the direction of the motor.
 The main advantage of these motors is the high starting
torque that they can produce. The starting torque can be as
high as 300 to 400% of the full load torque.

Fig.(2): Capacitor Start Capacitor Run Motor

• Applications:
Due to high starting torque, the capacitor start or
capacitor start capacitor run motors are used in
the following applications:
1. Grinders
2. Compressors
3. Conveyers
4. Fans and air conditioners
5. Refrigerators

Shaded Pole Induction Motor
• Fig.(1), shows the construction of a shaded pole
induction motor.
• Every stator pole is divided into two parts by keeping a
small slit in the pole face and the smaller portion is
covered with a thick short circuited copper wire called
shading band.
• When stator winding carries current, the main pole
produces a flux øm.
• This flux links with the shading band and this band cats
as a shorted secondary winding, stator winding being
its primary. Circulating currents induced tn the band
produced nother flux øs.

• At instant t1 current is increasing. The induced emf tries to
oppose it. Thus flux øs opposes it and resultant flux is in
unshaded part.
• At instant t2 current is almost constant. Induced emf and flux øs
are negligible. Resultant flux is almost at the center of the pole.
Thus it has shifted its position.
• At instant t3 current is decreasing. The induced current and flux
øs try to oppose this decrease. Resultant flux lies in shaded part.
• This action continues and the resultant field rotates from
unshaded part to shaded part. Hence rotor also rotates in the same
direction.
• The direction of rotation cannot be reversed unless position of
shaded ring is changed from one part of pole to another part.

• Such motor develops low starting torque and it
has a low power factor..
• Applications:
1. Table fans
2. Blowers
3. Washing machines
4. refrigerators

Fig.(1): shaded pole induction motor

Universal Motor
 The motors which can be operated satisfactorily on ac as
well dc supply is universal motor.
• Types of universal motors:
1. Uncompensated type universal motor
2. Compensated universal motor
• Windings:
 There are three windings used namely armature, main field
and compensating winding.
 Out of which compensating winding is used only for the
compensated universal motor.
 All the windings are connected in series with each other
since this is basically a series motor.

1. Uncompensated universal motor:
• The operating principle is same as that of dc
series motor.
• Field winding produces flux. It is stationary
winding. Armature is a rotary winding.
• These motors produces high starting torque but
their speed decreases with increase in load. Their
speed regulation is not very good.
• These motors having low capacity. Normally it is
designed for two pole structure.

Fig.(1): Uncompensated Universal Motor

2. Compensated universal motor:
• In this motor, main winding and compensating
winding are distributed over entire stator.
• Fig.(2) shows the schematic diagram of
compensated universal motor.
• This type of motor is better for higher speeds.
• These motors are more expensive due to
complicated construction. Hence they are
preferred for higher capacity loads.

Fig.(2):compensated Universal Motor

• Applications:
1. Washing machine
2. Mixers and grinders
3. Food processors
4. Small drilling machines
5. Vaccum cleaners
6. Sewing machine
7. Hair driers
8. Electric shavers

• Specifications and ratings of a universal
motor:
Sr. No. Specifications/rating Value
1. Type Compensated
2. Rated voltage 230 V
3. Number of phases 1
4. Power 0.5kW
5. Speed 5000 RPM

Stepper Motor
• Converts series of electrical pulses (input) into discrete angular
movements (definite angular steps) i.e one step for each pulse
input.
• Stator is constructed of laminated silicon steel.
• As shown the stator has six salient poles or teeth on which coils
are placed with opposite poles having series connected coils to
which voltage pulses are given through the switching circuit as
shown.
• Rotor is also of laminated silicon steel with the no. of poles/teeth
being four but has no coils.
• The switching is done sequentially to obtain rotation.
• When poles A & A’ are excited by closing Switch Sw1 the rotor
teeth nearest to these align to have minimum reluctance between
the A-A’ stator poles. (poles A and A’ are opposite in nature).

• Next if poles B & B’ are excited by opening Sw1 and
closing Switch Sw2 then the rotor moves anticlockwise
angularly by 30o to align with these poles.
• Thus if we provide 12 such voltage pulses sequentially
by proper opening and closing of switches we get one
full rotation in 12 equal steps.
• If the sequence of application of these pulses is A/A’ –
C/C’ – B/B’ then we obtain clockwise rotation.
• By changing the no of rotor teeth proportionally we can
have smaller angular steps.

Fig.(1): Construction Of Stepper Motor

• Applications:
1. In robotics and CNC machines
2. In computers, printers, tape readers etc.
3. In the applications like radars, satellite communication
systems.
4. In position control applications.
5. In the biomedical applications.
6. NC control of machine tools.
7. Process control systems
8. XY recorders and plotters
9. watches

• Specifications/ratings of a stepper motor:
1. Type
2. Number of phases
3. Number of poles
4. Maximum stepping rate
5. Maximum speed
6. Step angle
7. Slewing rate
8. Voltage
9. Torque

Servomotors
• In automatic control system it becomes
necessary to compare system parameters with
some reference.
• Whatever is the error it is amplified and used
to drive motors known as servomotors.
• Depending upon type od supply used,
servomotors are classified into:
1. A.C. servomotor and
2. D.C. servomotor

1. A.C. servomotors:
• Construction of ac servomotor is as shown in fig.(1).
• Basically it is an induction motor with two windings
provided on the stator.
• One of the winding is called reference or main winding
which is connected to constant magnitude ac voltage.
• The other winding is called control winding which is
connected to voltage obtained form servo amplifier.
• For maximum flux linking air gap kept is minimum.
• The ac servomotors are used in the frequency range of 50
Hz to 400 Hz and from milliwatts power consumption to
few hundred watts.

• Applications:
1. Process control equipments
2. Machine tools
3. Instruments servos
4. Sewing machine
5. Robotics
6. Process controllers
7. AC position control applications
8. Portable drilling machines

2. D.C. Servomotors:
• DC servomotor is an ordinary dc motor. But it is a
separately excited dc motor. The dc servomotors are
further classified into two types:
1. Armature controlled type and
2. Field controlled type.
• In field controlled dc servomotors, the signal from the
servo amplifier is applied to the field winding. The
armature is connected to constant current source.
• In armature controlled dc servomotor, the constant
current source is applied to the field winding whereas
the servo amplifier output is connected to the armature.

• Applications:
1. Position control system
2. Process controller
3. Machine tools
4. Robotics
5. Aircraft control system
6. Servo stabilizers

Introduction
• The machines that generate a.c. emf are called
synchronous generators or A. C. generators. It
is also called as an alternator.
• An alternator can be run as a motor called
synchronous motors. Both these machines i.e.
the alternator and synchronous motor work at a
specific constant speed.
• Hence, they are called synchronous machine.

Construction of an alternator
• In alternator, field windings are placed on the rotor and
the armature winding is placed in suitable shaped slots in
the stator.
• The field winding is connected to an external dc source
called exciter, through a pair of sliprings as shown in
fig.(1).
• The armature winding is 3 phase winding and the induced
voltage in this winding is supplied to the load. This is a 3
phase ac voltage.
• When the excited rotor rotates, its magnetic field cuts the
stationary stator conductor as a result of which a 3 phase
ac voltage gets induced into the armature winding.

Fig.(1): Construction Of An Alternator

Fig.(2): Detail Construction Of An
Alternator

Principle Of Operation
• The fig.(1) shows the construction of single turn alternator
to generate sinewave.
• This alternator consists of a permanent magnet with two
poles N and S and a single turn rectangular coil which is
made up of two conductors p and Q.
• These conductors are connected to each other on one end
whereas there other ends are connected to the slip rings
mounted on shaft.
• The single turn coil can rotate around its own axis in
clockwise or anticlockwise direction in the flux produced by
the permanent magnet.
• Due to rotation, the conductors P and Q cut the magnetic
lines of flux produced by permanent magnet.

• According to faraday’s law of electromagnetic
induction, an emf is induced into the rotating
conductors.
• Due to this induced emf, current flows through
the external resistance R.
• The induced emf in the single turn coil is given
by,
e = Blv sinθ
• Thus the single turn alternator produces a
sinusoidal voltage.

Applications
1. Hydroelectric power generation plant
2. Steam power stations
3. Wind mills
4. All the automobiles (two wheelers, cars,
trucks, buses etc.)
5. Nuclear power stations

chapter 5 (1).pptx

More Related Content

Similar to chapter 5 (1).pptx (20)

More from deepaMS4 (13)

Recently uploaded (20)

chapter 5 (1).pptx