Correlative Study on the Modeling and Control of Boost Converter using Advanced Controllers

IJSRD - International Journal for Scientific Research & Development| Vol. 3, Issue 10, 2015 | ISSN (online): 2321-0613
All rights reserved by www.ijsrd.com 494
Correlative Study on The Modeling and Control of Boost Converter using
Advanced Controllers
G.C. Sowparnika1 A. Sivalingam2 M. Thirumarimurugan3
1
P.G. Student 2
Associate Professor 3
Associate Professor and Head
1,2,3
Department of Chemical Engineering
1,2,3
Coimbatore Institute of Technology Coimbatore, Tamil Nadu, India
Abstract— DC-DC converters are switched power converters.
The converters are most widely used in research and
industrial applications. The DC-DC Boost Converters are
used to step-up the supply voltage given to the plant model.
The main advantage of using the Boost Converters is that it
works in the low voltage according to the design
specifications. In order to regulate the uncontrolled supply of
voltage, a controller has to be designed and modeled to
stabilize the output voltage. Since the convectional
controllers cannot work under dynamic operating conditions,
advanced controllers are to be designed to overcome the
problems. In this article, the advanced controllers such as
NARMA-L2, Fuzzy Logic (FLC) and Sliding Mode
Controllers (SMC) are implemented and their responses are
compared using MATLAB.
Key words: FLC, Duty Cycle (D), Design of Sliding Mode
Control (SMC)
I. INTRODUCTION
DC-DC boost converters usually provide variations in output
voltage with respect to input voltage. The free supply of
voltage and current leads to malfunctioning of the boost
converter. Control techniques such as analog and digital
methods are used [1]. DC-DC converters are intrinsically
non-linear circuits and it is difficult to obtain accurate models
which influences dynamic behaviour. The DC-DC converter
inputs are generally unregulated DC voltage input and the
required outputs should be a constant or fixed voltage.
Application of a voltage regulator is that it should maintains
a constant or fixed output voltage irrespective of variation in
load current or input voltage. Boost converters are widely
used for power monitoring of the renewable energy sources
such as solar cell, wind mills, wind generators and fuel cell
systems. Because of these advantages boost converters are
more extensively used in industrial applications. In this
article, the transient response of the converter system is
improved by NARMA-L2, FLC and SMC using MATLAB
and the responses are compared.
II. MODELING OF BOOST CONVERTER
The Boost converter is designed using the following
procedure:
The necessary parameter for the design of boost converter is
the input voltage, output voltage, output current and
switching frequency. Fig. 1 shows the basic circuit of boost
converter [2].
Fig. 1: Boost Converter Circuit.
A. Duty Cycle (D):
to determine the duty cycle D, for the minimum input voltage.
The minimum input voltage is used because it leads to the
maximum switching current.
D= 1-
Vin
Vo
Vin = input voltage
Vo = desired output voltage
1) Load Resistance (R):
R=
Vo
Io
Io = desired output current
2) Inductance (L):
L=
Vin∗(Vo−Vin)
∆Il∗fs∗Vo
∆Il = 10% of Io
Vin = input voltage
fs = switching frequency
∆Il = inductor ripple current
3) Capacitance (C):
C=
(Io∗D)
(fs∗∆Vo)
∆Vo = ESR(
Io
1 − D
+
∆Il
2
)
D = duty cycle
fs = switching frequency
∆Vo = output ripple voltage
∆Il = inductor ripple current
ESR = equivalent series resistance of the capacitor
4) Diode:
In order to reduce losses, ultra fast recovery diodes can be
used. The forward current rating needed is equal to the
maximum output current. From the above equations the
design parameters are obtained as shown in Table I.
Diode: In order to reduce losses, ultra fast recovery diodes
can be used. The forward current rating needed is equal to the
maximum output current. From the above equations the
design parameters are obtained as shown in Table I.
S.
NO.
PARAMETERS VALUES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Input Voltage (Vin)
Input Current (Iin)
Output Voltage (Vo)
Output Current (Io)
Duty cycle (D)
Switching frequency (fs)
Load Resistance (R)
Inductance (L)
Equivalent Series Resistance
(ESL)
60 V
5 A
300 V
1 A
0.8
2 KHz
300 Ω
240 mH
0.5Ω
5000 μF
(2)
(3)
(4)
(1)
(5)

Correlative Study on The Modeling and Control of Boost Converter using Advanced Controllers
(IJSRD/Vol. 3/Issue 10/2015/102)
11. Capacitance (C)
Equivalent Series Resistance
(ESR)
16 mΩ
Table I: Design Specifications
*Units: V- volt, A- ampere, Ω- ohms, mH- milli Henry, μF-
micro Farad
III. STATE SPACE MODELING
The modeling of DC-DC boost converter is carried out to
determine the state space model. The output and the control
transfer function of the system are obtained from the state
space model using MATLAB. This method is known as state
space averaging technique. The operation of the boost
converter takes place in two modes [3]:
A. Switch On Equivalent Circuit
Fig. 2: ON Mode Circuit
During OFF mode as shown in Fig. 3, the state equation
matrices are given by-
[
dil
dt
dvc
dt
] = [
−Rl+(R‖Rc)
L
−R
L(R+Rc)
R
C(R+Rc)
−1
(R+Rc)
] * [
il
vc
] + [
1
L
0
] * Vin
Vo= [(R‖Rc)
R
(R+Rc)
] * [
il
vc
] (7)
B. Switch Off Equivalent Circuit
Fig. 3: OFF Mode Circuit
During OFF mode as shown in Fig. 3, the state equation
matrices are given by-
[
dil
dt
dvc
dt
] = [
−Rl+(R‖Rc)
L
−R
L(R+Rc)
R
C(R+Rc)
−1
(R+Rc)
] * [
il
vc
] + [
1
L
0
] * Vin (8)
Vo= [(R‖Rc)
R
(R+Rc)
] * [
il
vc
]
The state space parameters A, B, C and D matrices for the
above equations are obtained for ON and OFF states. By
averaging techniques the determined matrices are:
Aavg =[
−2.06972 −0.8332
39.996 −0.666
]
Bavg = [
4.166
0
]
Cavg = [0.003198 0.999]
Davg = [0]
Using MATLAB, the output transfer function obtained is
Vo
Vin
=
0.0133s+166.5
s2+2.753s+34.72
(10)
IV. MODELING & IMPLEMENTATION OF CONTROLLER
The boost converter should always maintain constant voltage
with variations in the input parameters. In order to maintain a
stable output in the converter, an appropriate control signal
should be applied. In practice the switching network is highly
non-linear. An accurate mathematical modeling of the
switching network is very difficult to obtain. In addition there
are also reported problems of the supply voltage and load
current fluctuating over a wide range. A controller is designed
and modeled which yields the control transfer function and
the controller transfer function. Therefore a NARMA-L2
Controller, Fuzzy Logic controller and Sliding Mode Control
are implemented to achieve a proper system performance [4].
The occurrence of oscillatory behaviour of the boost
converter is mainly caused by the switching operation of the
semiconductor device. In order to stabilize the transient
response of the system, NARMA-L2, FLC and SMC are
implemented. By small signal modeling technique, the
control transfer function is determined.
Vo
d
=
−0.7999s2−996s+49500
s2+2.753s+34.72
A. Design Of NARMA-L2 Control
NARMA-L2 Controller is also called as Feedback
Linearization Control (FLiC). If the model is inn companion
form, then it is called as FLiC. When the converter model is
approximated in the same form, it is called as NARMA-L2
Control. The design of NARMA-L2 Control aims at
transforming the non-linear dynamics into linear dynamics by
nullifying the non-linear behaviour of the model [5]. Fig. 4
shows the simulink model of the NARMA-L2 Controller.
FLiC is used for identification of the system that is
to be controlled. Training of the ANN depicts the forward
dynamics of the converter model. Initially, the dynamics of
the converter model that is to be controlled should be chosen.
The standard model of NARMA-L2 control is
x(a+ b) = P[ x(a), x(a- 1), x(a - t +1),m(a),m(a -1), m(a - t +1)]
[12]
where m(a) is the system input, and x(a) is the
system output. Identification of the model can be done by
training the ANN to approximate the nonlinear function P.
The model output is given as
x(a + b) = xr(a + b) [13]
The controller of the model is given as
m(a) = Q[x(a), x(a -1), x(a - t +1), xr (a + b),x(a -1), x(a -t
+1)] [14]
Fig. 4: Simulink Model of NARMA-L2 Controller
(11)

B. Design Of Fuzzy Logic Controller (FLC)
The Fuzzy Logic Controller (FLC) are considered to be one
of intelligent controllers. This paper is using fuzzy logic
controller with feedback of voltage output respectively. The
voltage output in the circuit will be fed to fuzzy controller to
give appropriate measure on steady state signal [6]. FLC
offers an important concept of soft computing with words. It
provides technique which deals with imprecision. The fuzzy
theory provides mechanism for representation of linguistic
terms such as “many,” “low,” “medium,” “often,” “few.” In
general, the fuzzy logic provide an inference structure that
enable appropriate human reasoning capabilities. Fuzzy logic
systems are suitable for approximate reasoning. Fuzzy logic
systems have faster and smoother response than conventional
systems and control complexity is less. The fuzzy inference
system combines fuzzy IF–THEN rules for mapping from
fuzzy sets in the input space X to the output space Y based on
fuzzy logic principle. In fuzzy logic, knowledge
representation, fuzzy IF–THEN rule is a technique for
capturing knowledge that involve imprecision. The main
feature of reasoning using fuzzy rules is its partial matching
capability, an inference to be made from fuzzy rule even
when the rule’s conditions are partially satisfied [7]. Fig. 5
shows the simulink model of the FLC. Table 2 shows the rule-
base for the boost converter.
Fig. 5: Simulink Model of FLC
e
ce
MN NB N Z P PB MP
MN MN MN MN MN NB N Z
NB MN NB NB NB N Z P
N MN NB N N Z P PB
Z MN NB N Z P PB MP
P NB N Z P P PB MP
PB N Z P PB PB PB MP
MP Z P PB MP MP MP MP
Table II: Rule Base
*ce- change of error, e- error
C. Design Of Sliding Mode Control (SMC)
SM controller is a type of non-linear controller. It is employed
and adopted for controlling variable structured systems
(VSSs). It is very easy to implement as compared to other
types of nonlinear and classical controllers [8]. Two
important steps in SM control is to design a sliding surface in
state space and then prepared a control law to direct the
system state trajectory starting from any arbitrary initial state
to reach the sliding surface in finite time, and at the end it
should arrive to a point where the system equilibrium state
exists that is in the origin point of the phase plane. There are
three important factors responsible for the stability of SM
controllers, existence, stability, and hitting condition. The
sliding line divides the phase plane into two main regions.
Each region is represent by a switching state and when the
trajectory comes at the system equilibrium point, in this case
the system is considered as stable system [9].
Fig. 6 shows simulink model of the sliding mode
control technique that operates at infinite switching
frequency. But practical SM controllers are operated at finite
switching frequencies represent a quasi-sliding mode [10].
The transfer function for the compensator is determined as
6.3443s2
+ 49.8473s + 101.73
s2 + 100s
Therefore the overall control transfer function is
−0.5083s6−6327s5+(2.583∗105)s4+(3.906∗106)s3
+(2.385∗107)S2+(1.308∗108)s+(1.75∗108)
s6+84.55s5+1452s4+(1.744∗104)s3+(8.935∗104)s2
+(4.408∗105)s+(5.834∗105)
Fig. 6: Simulink Model of SMC
V. RESULTS AND DISCUSSIONS
In this section, the output response of the NARMA-L2, FLC
and SMC controllers are compared and the response shows
that the performance of the boost converter is improved. Fig.
7, 8 and 9 shows the response of the advanced controllers.
Fig. 7: Response of NARMA-L2 Controller
(15)
(16)

Fig. 8: Response of FLC
Fig. 9: Response of SMC
VI. CONCLUSION
In this article, the boost converter for the desired specification
was obtained. The advanced controllers such as NARMA-L2
Control, FLC and SMC are modeled and designed. In this, the
SMC have produced an improved output response using
MATLAB. Since the advanced controllers are used, the Boost
Converter operates in the dynamic operating conditions.
Further this work can be developed into hardware using the
required components and arduino boards.
REFERENCES
[1] Sowparnika G C, Sivalingam A and Thirumarimurugan
M, “Evaluation of Control Techniques in DC-DC
Converters”, International Journal of Emerging
Technology & Research, vol.2, no.4, pp.1-8, 2015.
[2] Dhivya B S, Krishnan V and Ramaprabha R, “Neural
Network Controller for Boost Converter”, In
Proceedings of International Conference on Circuits,
Power and Computing Technologies [ICCPCT-2013],
pp.246-251, Jan, Research Gate, 2013.
[3] Brigitte Hauke, “Basic Calculation of a Boost
Converter’s Power Stage”, Application Report
SLVA372C, Texas Instruments, 2014.
[4] Abdul Fathah, “Design of Boost Converter”,
Department of Electrical Engineering, National Institute
of Technology, Rourkela 2013.
[5] Mark Hudson Beale, Martin T. Hagan and Howard B.
Demuth, “Neural Network Toolbox- User’s Guide”,
MATLAB, The Math Works Inc., 2015.
[6] Rajesh Kr Ahuja and Rajesh Kumar, “Design and
Simulation of Fuzzy Logic Controller based Switched-
Mode Power Supply”, International Journal of
Electrical Engineering, vol.2(5), pp.16-21, 2014.
[7] Chetan P. Ugale, R. B. Dhumale and V. V. Dixit, “DC-
DC Converter Using Fuzzy Logic Controller”,
International Journal of Engineering and Technology,
vol.2(4), pp.593-596, 2015.
[8] Tamal Biswas, Prof. G KPanda, Prof. P KSaha and Prof.
S Das, “Design of PWM-Based Sliding-Mode Control
of Boost Converter with Improved Performance”,
International Journal of Advanced Research in
Electrical, Electronics and Instrumentation
Engineering, vol. 4(2), pp. 817-824, 2015.
[9] Hanifi Guldemir, “Study of Sliding Mode Control of
Dc-Dc Buck Converter”, Energy and Power
Engineering, vol.3, 2011.
[10]R. A. Abdulhalem, Haroutuon A. Hairik, Hisham L.
Swady and Asmaa J. Kadhem, “Modeling and
Simulation of PWM Sliding Mode Voltage Controller
for DC/DC Boost Converters Operating in Continuous
Conduction Mode”, Academicia, pp. 1-13.

Correlative Study on the Modeling and Control of Boost Converter using Advanced Controllers

More Related Content

What's hot (20)

Viewers also liked (13)

Similar to Correlative Study on the Modeling and Control of Boost Converter using Advanced Controllers (20)

More from IJSRD (20)

Recently uploaded (20)

Correlative Study on the Modeling and Control of Boost Converter using Advanced Controllers