Current and power using hall sensors
Download as PPTX, PDF•0 likes•1,632 views
This document discusses Hall effect sensors and their applications. Hall effect sensors use the Hall effect principle to sense magnetic fields or electric current. They have simple and inexpensive designs, producing an output voltage proportional to the magnetic field. Common applications include sensing motor speed and position, measuring current, and detecting changes in magnetic fields. Hall effect sensors are widely used due to their low cost, ease of integration, and ability to provide non-contact sensing of magnetic fields and current.
![Hall effect - principles
Consider a block of conducting medium through
which a current of electrons is flowing caused by
an external field
A magnetic filed B is established across the
conductor, perpendicular to the current (.
The electrons flow at a velocity v
A force perpendicular to both the current and
field is established.
F= qvBsinvb [N]](https://image.slidesharecdn.com/currentandpowerusinghallsensors-150509072009-lva1-app6891/85/Current-and-power-using-hall-sensors-3-320.jpg)
![Hall effect - principles
The electrons are pulled towards the front
side surface of the conductor (holes in
semiconductors move towards the back)
A voltage develops between the back
(positive) and front (negative) surface. This
voltage is the Hall voltage and is given by:
Vout = IB
qnd
V
d is the thickness of the hall plate,
n is the carrier density [charges/m3] and
q is the charge of the electron [C]](https://image.slidesharecdn.com/currentandpowerusinghallsensors-150509072009-lva1-app6891/85/Current-and-power-using-hall-sensors-6-320.jpg)
![ If the current changes direction or the magnetic
field changes direction, the polarity of the Hall
voltage flips.
The Hall effect sensor is polarity dependent,
may be used to measure direction of a field
or direction of motion if the sensor is properly set up.
The term 1/qn [m3/C] is material dependent
and is called the Hall coefficient KH.](https://image.slidesharecdn.com/currentandpowerusinghallsensors-150509072009-lva1-app6891/85/Current-and-power-using-hall-sensors-7-320.jpg)
Current and power using hall sensors
- 1. CURRENT AND POWER USING HALL SENSORS
- 2. Hall effect sensors Hall effect was discovered in 1879 by Edward H. Hall Exists in all conducting materials Is particularly pronounced and useful in semiconductors. One of the simplest of all magnetic sensing devices Used extensively in sensing position and measuring magnetic fields
- 3. Hall effect - principles Consider a block of conducting medium through which a current of electrons is flowing caused by an external field A magnetic filed B is established across the conductor, perpendicular to the current (. The electrons flow at a velocity v A force perpendicular to both the current and field is established. F= qvBsinvb [N]
- 4. Theory Thus R=Vh/aJH=Vhb/IH Vh is Hall Voltage and I is Jab
- 5. Hall effect - principle
- 6. Hall effect - principles The electrons are pulled towards the front side surface of the conductor (holes in semiconductors move towards the back) A voltage develops between the back (positive) and front (negative) surface. This voltage is the Hall voltage and is given by: Vout = IB qnd V d is the thickness of the hall plate, n is the carrier density [charges/m3] and q is the charge of the electron [C]
- 7. If the current changes direction or the magnetic field changes direction, the polarity of the Hall voltage flips. The Hall effect sensor is polarity dependent, may be used to measure direction of a field or direction of motion if the sensor is properly set up. The term 1/qn [m3/C] is material dependent and is called the Hall coefficient KH.
- 8. Hall coefficient The hall voltage is usually represented as: Vout = KH IB d V • Hall coefficients vary from material to material • Are particularly large in semiconductors. • Hall voltage is linear with respect to the field for given current and dimensions. • Hall coefficient is temperature dependent and this must be compensated if accurate sensing is needed.
- 9. Hall coefficient - cont. Hall coefficient is rather small - of the order of 50 mV/T Most sensed fields are smaller than 1 T The Hall voltage can be as small as a few V Must in almost all cases be amplified. Example, the earth’s magnetic field is only about 50 T so that the output is a mere 25 V
- 10. Hall effect sensors - practical considerations Hall voltages are easily measurable quantities Hall sensors are among the most commonly used sensors for magnetic fields: simple, linear, very inexpensive, available in arrays can be integrated within devices. Errors involved in measurement are mostly due to temperature and variations and the averaging effect of the Hall plate size These can be compensated by appropriate
- 11. Hall effect sensors - fabrication A typical sensor will be a rectangular wafer of small thickness Made of p or n doped semiconductor (InAs and InSb are most commonly used because of their larger carrier densities – hence larger Hall coefficients) Silicon may also be used with reduced sensitivity) The sensor is usually identified by the two transverse resistances – the control resistance through which the control current flows and the output resistance across which the Hall voltage develops.
- 12. Hall effect sensors - applications In practical applications, the current is usually kept constant so that the output voltage is proportional to the field. The sensor may be used to measure field (provided proper compensation can be incorporated) It may be used as a detector or to operate a switch. The latter is very common in sensing of rotation which in itself may be used to measure a variety of effect (shaft position, frequency of rotation (rpm), position, differential position, etc.).
- 13. Hall effect sensors - applications Example is shown in Figure 5.31 where the rpm of a shaft is sensed. Many variations of this basic configuration: for example, measurement of angular displacement. Sensing of gears (electronic ignition) Multiple sensors can sense direction as well
- 14. Hall element as a rotation sensor
- 16. Hall effect sensors - applications Example: measuring power The magnetic field through the hall element is proportional to the current being measured The current is proportional to voltage being measured The Hall voltage is proportional to product of current and voltage - power
- 17. Hall element power sensor
- 18. Applications Hall effect devices produce a very low signal level and thus require amplification. In early 20th century vacuum tube amplifiers were expensive and unreliable. But with the development of the low cost integrated circuit the Hall effect sensor became suitable for mass application.
- 19. Some Hall element sensors
- 20. A 3-axis Hall element probe
- 21. Hall sensors used to control a CDROM motor
- 22. Current Sensor When electrons flow through a conductor, a magnetic field is produced. Thus, it is possible to create a non-contacting current sensor. This has several advantages: 1.No additional resistance (a shunt) need be inserted in the primary circuit. 2.Also, the voltage present on the line to be sensed is not transmitted to the sensor, which enhances the safety of measuring equipment. Hall effect current sensor with internal integrated circuit amplifier.