Design of all digital phase locked loop (d pll) with fast acquisition time

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 02 Issue: 12 | Dec-2013, Available @ http://www.ijret.org 536
DESIGN OF ALL DIGITAL PHASE LOCKED LOOP
(D-PLL) WITH FAST ACQUISITION TIME
M. Bharath Reddy 1
, M. Sai Sarath Kumar 2
, B. Suresh Kumar 3
1
M.Tech, School Of Electronic And Engineering, Vellore Institute Of Technology, Tamil Nadu,India,
2
3
bharathreddym91@rediffmail.com, mssk.2728@gmail.com, bandaru.suresh452@gmail.com
Abstract
A Digital PLL is designed with improved acquisition time and power efficiency. The implemented D-PLL can operate
from 6.54MHz to 105MHz with a power dissipation of is 7.763µW (at 210MHz) with 1.2V supply voltage. The D-PLL is
synthesized using cadence RTL compiler in 45nm CMOS process technology.
Keywords: Digital PLL, Digital Phase/Frequency detector, NCO, Divide by N counter.
--------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
Phase locked loops are widely used in frequency synthesis
applications [2], [4]. For many portable applications the
acquisition time of PLL is very important so the design of
PLLs with minimum acquisition time is the primary goal
of this work .A Phase Locked Loop (PLL) is a feedback
system that compares the output phase with the input
phase to produce an output signal that has the same phase as
that of an input signal. PLL’s are found in many
applications such as reference generation, frequency
synthesis, frequency multiplication, FM demodulation etc.
As the frequency of operation increases, the need of
generating signals that are in phase lock with input (i.e.
fast varying signals) is becoming a problem. There are two
types of PLL’s 1.Analog PLL 2.Digital PLL. Traditional
PLL’s are Analog PLL’s are shown in fig.1
PFDReference
input
VCO OutputLPF
Fig.1 Block diagram of Analog PLL
It uses phase detector to compare the input phase with the
output phase. Loop filter is used to reduce the ripples on the
control voltage of VCO. VCO is used to adjust the output
frequency such that the loop is locked and the output signal
is the replica of the input signal.Analog PLLs occupy
larger chip area due to the use of capacitors in feed forward
path. It has some other disadvantages such as sensitive to
noise and difficulty in converting to different processes and
etc. Whereas D-PLLs are compact and high immune to
noise. Moreover D-PLLs are easily programmable (i.e. easy
process conversion).
2. D-PLL ARCHITECTURE
The block diagram representation of a D-PLL is shown in
fig.2. The below architecture is simple and easy to
implement.
PFD
UP
COUNTER
DOWN
NCO
D
+
REFERENCE
INPUT
NCO
OUTPUT
ANALOG SECTION
Accumulator
+
D
Fig.2 Block diagram of D-PLL
The D-PLL architecture shown above has four major blocks,
namely the phase/frequency detector (PFD), the time to
digital converter (TDC), the accumulator and the
numerically control oscillator (NCO).The NCO is
implemented by using frequency divider circuit. The PFD
detects the phase or frequency difference between the
reference clock and output clock. The output of the PFD is
given to TDC which is continuous in time. The time to
digital converter generates a count value which is
proportional to the phase error. The average value (DC
value) of the PFD is accumulated by the accumulator block.
The accumulated valve determines the control word for the
NCO to oscillate with an appropriate frequency.

_______________________________________________________________________________________
Analysis of Individual Blocks
A. Phase Detector:
The Phase detector (PD) is a circuit that compares the
phase difference between the two input signals. It
generates an output signal whose average value is
linearly proportional to the phase difference between the
two input signals. There are number of ways in which a
Phase Detector can be realized, but we mostly consider
two types. They are 1) XOR-gate 2) PFD.
a) XOR-Gate Phase Detector:
The XOR-gate produces an output when both the
inputs are unequal, otherwise zero. The XOR gate
Produces output both at the rising edge and falling
edge of a cycle. The below equation gives the input-
output relationship of an XOR- gate Phase Detector
π/2 π 3π/2 2π-π-2π
v0
V0/2
vout
Fig.3 I/O Characteristics of XOR-Gate Phase
Detector.
As it can be seen from the above characteristics, the
problem of XOR-gate Phase Detector is its linearity range is
limited to π. When the phase difference is greater than π then
its average output value decreases. So we go for flip- flop
base phase Detector or Phase Frequency Detector.
b) Phase Frequency Detector(PFD):
The circuit shown in fig.4 can serve as both
phase/frequency detectors. It has three states, initially both
and equal to zero. If input A leads input B, first goes high
at the rising edge of input A (since is connected to logic 1),
then goes high at the rising of input B (since is also
connected to logic 1), causing the output of the NAND gate
to go to low, thereby resetting both and .Similarly if
input B leads input A then goes high first edge.
inputA
inputB
vdd
Up
Down
D Q
reset
Reset
D Q
vdd
Fig.4 Block diagram of PFD
Fig.5 Output waveforms of PFD
The circuit consists of two positive edge
triggered, negative edge resettable D-flip-flop having tied
their inputs to logical 1.The input’s of interest serves as a
clock to flip-flop. The input’s of interest serves as a clock to
flip-flop. The input output characteristics of the phase
frequency detector is shown below:
v0
2π
0 2π 4π
∆ø
vout
Fig.6 Input-Output characteristics of PFD
From fig.6 it is clear that the main advantage of
Phase Frequency Detector is that it’s improved linearity
range and the ability to act as a frequency detector as well.
B. Integrator:
The integrator block consists of time to digital converter
plus discrete time accumulator (1 tap IIR filter) to provide a
fixed value to the NCO
a) Time to digital converter:
The time to digital converter block is used to
convert the output of the Phase Frequency Detector which is
continuous into a digital number. The time to digital

_______________________________________________________________________________________
conversion can be achieved simply by using a counter which
is capable of counting up and down. The following analysis
has shown that the output count value is proportional to the
input Phase Difference.
Fig.8. Output Waveforms of Time to Digital Converter
Let C= Counter Output;
C (t) = time varying state of Up/Down counter.
=Counter clock period.
T=time period of input or phase detector cycle period.
C= ----- (1)
If is very small i.e. if 0 then ∑ becomes
integration.
C= ------- (2)
If there are cycles in T seconds then
= --------- (3)
Where =counter clock frequency.
= .T
C= = =
------ (4)
From equation (4) it is clear that the output
count value C is proportional to the input phase
difference .
b) Accumulator (Discrete time integrator):
The accumulator block is used to provide a
constant number (control_ word) to the Number Control
Oscillator (NCO). The accumulator block is analogous to
the LPF (integrator) in analog PLL. The accumulator block
accumulates the phase difference between the reference
clock and the output clock to provide a constant value to the
NCO. Otherwise the input to the NCO varies periodically
with time which results in varying frequency at the output
thus phase locking cannot be achieved.
C. Number Control Oscillator (NCO):
The Output frequency of the NCO is numerically
controlled by using a binary word instead of voltage. That is
the NCO generates an output signal whose frequency is
proportional to the input control word (binary format). There
are many ways to implement NCO block but the simplest
way to implement NCO is counter based approach. The
NCO consists of counter capable of dividing the input clock
based on its control word. The applicability of this device as
NCO is explained below.
*Controlword
----- (1)
Where k= Resolution = , n= No. of bits in counter.
The resolution of NCO increases by increasing the number
of bits. The higher the control word, higher the frequency
and vice-versa.
41 2 3
controlword
Output freqency`
Fig.10 Input- output characteristics of NCO
From equation (1), it is clear that the NCO can be
implemented using counter, whose output frequency is
based on the Control word. The maximum input frequency
that can be locked depends on the NCO resolution

_______________________________________________________________________________________
(k= ).The counter based NCO frequency range is
.
3. SIMULATION RESULTS:
Fig.11 Output waveforms of PLL at 210MHz
Fig .11 shows the Output waveforms of the PLL
where the reference clock is 52.35MHz. The D-PLL is
synthesized using cadence RTL compiler in 45nm CMOS
process. The D-PLL is implemented with following
specifications.
Specifications:
1. Maximum NCO frequency = 209.42 MHz
2. Free running frequency of NCO = 130.8MHz.
3. NCO resolution = = 6.54MHz; n=5 bit.
4. Input Frequency = 7MHz.
From the comparison table it is clear that power
dissipation of the proposed D-PLL is minimal compared to
that of All Digital cell based PLL [1], Analog PLL [2],
Semi-Digital PLL [3]. The acquisition time of proposed D-
PLL is less than Digital cell based PLL[1] and analog
PLL[2] i.e. proposed D-PLL is faster than the other two
PLLs proposed in [1],[2].
Table 1.Performance Comparison
4. CONCLUSION:
The D-PLL is implemented with standard cells in a 0.045µm
technology and can operate from 6.54MHz to 105MHz. The
presented D-PLL architecture is simple and easy to
implement. The acquisition time is 18 cycles.
REFERENCES:
[1] H.-T.Ahm and D.J.Allstot,”A low-jitter 1.9-V
CMOS PLL for ultraSPARC microprocessor
applications,”IEEE J.Solid-States Circuits,
vol.35,pp.450-454,May 1999.
[2] I.Hwang, S.Lee, S.Lee and S.Kim,”A digitally
controlled phase locked loop with fast locking
scheme for clock synthesis applications,”in IEEE
Int.Solid-State circuits Conf.Dig.Tech.Papers,
Feb.2000, pp.168-169.
[3] A. Young, M. F. Mar, and B. Bhushan, “A 0.35-m
CMOS 3-880-MHz PLL N/2 clock multiplier and
distribution network with low jitter for
microprocessors,” in IEEE Int. Solid-State Circuits
Conf. Dig. Tech. Papers, Feb. 1997, pp. 330–331.
[4] Ching-Che Chung and Chen-Yi Lee,”An All-
Digital Phase-Locked Loop for High-Speed Clock
Generation,” IEEE JOURNAL OF SOLID STAES
CIRCUITS, VOL.38, NO.2, FEBRUARY
2013.
BIOGRAPHIES:
M.Sai Sarath Kumar:
received B.Tech degree in
Electronics and
Communication Engineering
from CVR College of
Engineering,Hyderabad.Purs
uing M.Tech in VIT
University,Vellore,India
M.Bharath Reddy:
received B.Tech degree in
Electronics and
Communication Engineering
from AVS&SVR College of
Engineering,Nandhyal.
Pursuing M.Tech in VIT
University,vellore,India.
B. Suresh Kumar: received
B.Tech degree in Electronics
and Communication
Engineering from Avanti
College of Engineering,
Vazianagaram. Pursuing
M.Tech in VIT
University,Vellore,India

Design of all digital phase locked loop (d pll) with fast acquisition time

More Related Content

What's hot (20)

Viewers also liked (13)

Similar to Design of all digital phase locked loop (d pll) with fast acquisition time (20)

More from eSAT Journals (20)

Recently uploaded (20)

Design of all digital phase locked loop (d pll) with fast acquisition time