Gigaset e490 e495 telephone user guide

E490-E495

Issued by
Gigaset Communications GmbH
Schlavenhorst 66, D-46395 Bocholt
Gigaset Communications GmbH is a trademark licensee of Siemens AG
© Gigaset Communications GmbH 2008
All rights reserved.
Subject to availability. Rights of modifications reserved.
www.gigaset.com

Cyan

Magenta

Yellow

Black

Bedienungsanleitung SL780-SL785

22.08.08

V3

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / overview.fm / 19.02.2009

The handset at a glance

¢

The handset at a glance

18
17
16

¼

Ã½ V

1
2

¢

INT 1
01.10.09
INT

page 17)
3 Display keys (
4 Message key
Access to calls and message lists;
Flashes: new message or new call
5 End call key, On/Off key
End call, cancel function, go back one menu
level (press briefly), back to idle status (press
and hold), activate/deactivate handset
(press and hold in idle status)
6 Hash key
Keypad lock on/off (press and hold in
idle status);
swaps between upper/lower case and digits
7 Call-by-call list key
Open call-by-call list
8 Connection socket for headset
page 14)
(
9 Microphone
10 Recall key
- Consultation call (flash)
- Insert a dialling pause (press and hold)
11 Star key
Ringer on/off (press and hold),
With an open connection: switch between
dial pulsing/tone dialling (press briefly);
Text input: Open table of special characters
12 Key 1
Dial answering machine (E495 only)/
network mailbox (press and hold)
13 Talk key
Answer a call, open last number redial list
(press briefly), start dialling (press and hold)
When writing an SMS: send SMS
14 Speaker key
Switch between earpiece and speaker
mode;
Lights up: speaker activated;
Flashes: incoming call
page 16)
15 Control key (
page 45)
16 Eco Mode enabled (
17 Answering machine symbol (E495 only)
Answering machine switched on;
Flashes: Answering machine is recording a
message or is being operated by another
internal party
page 45)
18 Eco Mode+ enabled (

09:45
SMS

3

15
14

4

13

5

12

11

6

10

7

9
8
1 Display in idle status
2 Charge status of the batteries
= e V U (flat to full)
= flashes: batteries almost flat
e V U flashes: batteries
charging

¢

¢

¢

Version 4, 16.09.2005

Gigaset service contact numbers:
For personal advice on our range of products and for repairs or guarantee/warranty claims call:

Service Centre UK:

08453 6708 12
(local call cost charge)

Please have your proof of purchase ready when calling.

1

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / overview.fm / 19.02.2009

The base station at a glance

The base station at a glance

Version 4, 16.09.2005

Registration/Paging key (¢ page 47)

2

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / E495IVZ.fm / 19.02.2009

Contents

Contents
The handset at a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
The base station at a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
First steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Check the pack contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the base station and charging cradle . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the charging cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting up the handset for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
What would you like to do next? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using the phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Control key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keys on the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correcting incorrect entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating the keypad lock . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Illustration in the user guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16
17
17
17
17
18
18
19

Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Making calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Making an external call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling Line Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch to on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22
22
22
22
23
23

Making calls using network services . . . . . . . . . . . . . . . . . . . . . . 24
Calling Line Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ringback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call waiting during an external call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call divert (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consultation call, call swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24
24
24
25
25

Version 4, 16.09.2005

Using the directory and lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Directory/call-by-call list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Last number redial list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Opening lists with the message key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3


Contents

Making cost-effective calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Linking call-by-call numbers with one number . . . . . . . . . . . . . . . . . . . . . . . 30
Automatic network provider code (preselection) . . . . . . . . . . . . . . . . . . . . . 30

SMS (text messages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Writing/sending an SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiving an SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notification by SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMS mailboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting SMS centres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMS on a PABX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating first ringer muting . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating SMS function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMS troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

31
32
34
34
35
36
36
36
37

Operating the answering machine of the Gigaset E495
base station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Operation via the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating call screening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up the answering machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting fast access for the answering machine using key 1 . . . . . . . . . . .
Operating when on the move (remote operation) . . . . . . . . . . . . . . . . . . . .

38
41
42
42
43

Using the network mailbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Configuring fast access for the network mailbox . . . . . . . . . . . . . . . . . . . . . 44
Viewing the network mailbox message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

ECO DECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Setting the alarm clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Using several handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Registering handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
De-registering handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locating a handset ("paging") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making internal calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening in to an external call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the name of a handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a handset's internal number . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

46
47
47
47
48
49
49

Version 4, 16.09.2005

Using a handset as a room monitor . . . . . . . . . . . . . . . . . . . . . . . 49

4


Contents

Handset settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Quick access to functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the display language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the screen picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the display lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating auto answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the speaker/earpiece volume . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing ringers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating advisory tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring the handset default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51
51
51
52
52
52
52
53
54
54

Base station settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Protecting against unauthorised access . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating music on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeater support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring the base station to the factory settings . . . . . . . . . . . . . . . . . . . .

54
55
55
55

Connecting the base station to the PABX . . . . . . . . . . . . . . . . . . 56
Dialling modes and recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving an access code (outside line code) . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting pauses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching temporarily to tone dialling (DTMF) . . . . . . . . . . . . . . . . . . . . . . .

56
56
57
57

Service (Customer Care) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Questions and answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Authorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Guarantee Certificate
United Kingdom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact with liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Writing and editing text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61
61
62
63

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Mounting the base station to the wall . . . . . . . . . . . . . . . . . . . . 66
Mounting the charging cradle to the wall . . . . . . . . . . . . . . . . . . 66

Version 4, 16.09.2005

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

5

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / security.fm / 19.02.2009

Safety precautions

Safety precautions
Warning
Read the safety precautions and the user guide before use.
Explain their content and the potential hazards associated with using the telephone to
your children.

$

Only use the mains adapter supplied, as indicated on the underside of the base
station or charging cradle.
Only use the recommended, rechargeable batteries (¢ page 62), i.e. never
use a conventional (non-rechargeable) battery or other battery types as this
could result in significant health risks and personal injury.
The operation of medical appliances may be affected. Be aware of the technical
conditions in your particular environment, e.g. doctor's surgery.
Do not hold the rear of the handset to your ear when it is ringing or when the
speaker function is activated. Otherwise you risk serious and permanent damage to your hearing.
The handset may cause an unpleasant humming noise in hearing aids.
Do not install the base station or charging cradle in bathrooms or shower rooms.
The base station and charging cradle are not splashproof (¢ page 61).
Do not use your phone in environments with a potential explosion hazard
(e.g. paint shops).

ƒ

If you give your Gigaset to someone else, make sure you also give them the
user guide.
Please remove faulty base stations from use or have them repaired by our
Service department, as they could interfere with other wireless services.

Please note

Version 4, 16.09.2005

Not all of the functions described in this user guide are available in all countries.

6

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / starting.fm / 19.02.2009

First steps

First steps
Check the pack contents
1

4

2

3

5
6

7

Version 4, 16.09.2005

J

8

K

9

L

1 one Gigaset E490/E495 base station
2 one mains adapter for the base station
3 one Gigaset E49H handset
4 one charging cradle
5 one mains adapter for the charging cradle
6 two batteries
7 one battery cover
8 one belt clip
9 one lock ring
J one phone cord
K one rubber headset socket cover
L one user guide
7


First steps

Installing the base station and charging cradle
The base station and charging cradle are designed for use in enclosed dry
rooms with a temperature range of +5°C to +45°C.
¤ Place the base station in a central location in your flat or house. Position the
base station and charging cradle on a level, non-slip surface or mount them
on the wall ¢ page 66.

Please note

u Pay attention to the range of the base station.

This is up to 300 m in unobstructed outdoor areas and up to 50 m inside
buildings.
u The range is reduced when eco mode is on (¢ page 45).
The phone's feet do not usually leave any marks on surfaces. However, due to
the multitude of different varnishes and polishes used on today's furnishings,
the occurrence of marks on the surfaces cannot be completely ruled out.

Please note:
u Never expose the telephone to the influence of heat sources, direct sunlight

or other electrical devices.

u Protect your Gigaset from moisture, dust, corrosive liquids and vapours.

Connecting the base station

¤ First connect the
¤

mains adapter 1.
Then connect the
telephone jack 2
and insert the
cables into the
cable ducts.

1
1
2

Please note:
u The mains adapter must always be connected, as the phone will not oper-

Version 4, 16.09.2005

ate without mains connection.
u Only use the mains adapter and phone cord supplied. Pin connections on
telephone cables can vary (pin connections ¢ page 62).

8


First steps

Connecting the charging cradle

¤ Connect the flat plug of the mains

2

adapter 1.

1

¤ Plug the mains adapter into the
plug socket 2.

2
If you need to disconnect the plug from the
charging cradle, press the release button 1
and disconnect the plug 2.

Version 4, 16.09.2005

1

9


First steps

Setting up the handset for use
The display and control key are protected by a plastic film.
Please remove the protective film!

Inserting the batteries and closing the battery cover
Warning
Only use the rechargeable batteries recommended by Gigaset Communications GmbH * (¢ page 62), i.e. never use conventional (non-rechargeable)
batteries, as this could result in significant health risks and personal injury.
For example, the outer casing of the batteries could be damaged or the batteries could explode. The phone could also malfunction or be damaged as
a result of using batteries that are not of the recommended type.
* Gigaset Communications GmbH is a licensee of the Siemens trademark.

¤ Insert the batteries the right way round.
The polarity is indicated in/on the battery compartment.

¤ Hold the battery cover at a

b

¤

a

¤ Insert the lock ring or belt clip

Version 4, 16.09.2005

¤

10

into the battery cover as shown
(at an angle of approx. 20°).
Pay attention to the arrow markings on the lock ring.
Turn the lock ring or belt clip
clockwise to the end stop.
The lock ring is closed once the
markings on the ring are aligned
with those on the cover.

slight angle and insert the bottom into the casing first a.
Then press the cover b until it
clicks into place.


First steps

¤ Insert the rubber headset socket
cover provided to guarantee the
unit is splashproof.

If you need to reopen the battery cover, for instance to change the batteries,
please proceed as follows:
¤ Turn the lock ring or belt clip
anti-clockwise to the end stop
(approx. 20°) and remove.
Position your thumb and index
finger on both sides of the lock
ring.
¤ Insert a suitable tool (e.g. a
small coin) into the cavity at the
top of the battery cover and
twist it until the cover opens.

Placing the handset in the charging cradle

¤ Insert the mains adapter of the charging cradle into the mains socket.
¤ Place the handset in the charging cradle with its display facing forward.

The handset is registered with the base station at the factory. You do not need
to complete a registration. If you wish to use your handset with a different base
station or use further handsets with your base station, you will have to register
the handset manually ¢ page 46.
To charge the battery, leave the handset in the charging cradle.

Please note

Version 4, 16.09.2005

Only place the handset in the charging cradle that is intended for it.

11


First steps

First battery charge and discharge
The correct charge status can only be displayed if the battery is first fully
charged and discharged.

¤ Place the handset in the charging cradle for
six hours.

6h

¤ Once the battery is fully

charged, remove the
handset from the charging
cradle and do not put it
back again until the battery is fully discharged.

Please note

u After the first battery charge and discharge, you may place your handset

in the charging cradle after every call.

u Always repeat the charging and discharging procedure if you remove the

battery from the handset and reinsert it.

u The battery may heat up during charging. This is not dangerous.
u After a time, the charge capacity of the battery will decrease for techni-

Version 4, 16.09.2005

cal reasons.

12


First steps

Setting the date and time
Set the date and time so that the correct date and time can be assigned to
incoming calls, and so that the alarm can be used.

Time

and time, press the key below
§Time§ to open the input field.

¤ The active line is marked [...].

Date/Time

Enter day, month and year as a
6-digit number via the keypad,
e.g. Q

QQO
for 01/10/2009.

Date
[01.10.09]
Time
00:00

Ý

¤ If you have not yet set the date

Save

¤ Press down on the control key
to enter the time.

¤ Enter the hours and minutes in

Date/Time

4-digit format via the keypad,
e.g. Q M
5
for 07:15 am.

Date
01.10.09
Time
[07:15]
Save

Ý

Version 4, 16.09.2005

Ý

Save

¤ Press the key below §Save§ on

the display screen to confirm
your setting.

13


First steps

Display in idle status
Once the phone is registered and the time set, the idle display is shown as in
this example. If the answering machine is activated, the answering machine
icon × will also be displayed in the header.

Displays

¼
Eco Mode+ activated (¢ page 45)
½
Eco Mode activated (¢ page 45)
Charge status of the batteries:
= e V U (flat to full)
= flashes: batteries almost flat
INT 1 Internal name of the handset
(¢ page 49)

¼

½

V

INT 1
01.10.09
INT

07:15
SMS

If Eco Mode+ (¢ page 45) is not activated, the top left of the display shows
the quality of the radio contact between the base station and handset:
u Good to poor: Ð i Ñ Ò
u No reception: | flashes
Your answering machine is set with a pre-recorded announcement.

Your phone is now ready for use!

Connecting the headset
After removing the rubber cover, you can
connect a headset to the underside of
your telephone with the 2.5 mm jack connector. HAMA and Plantronics M40,
MX100 and MX150 headsets are all suitable.
After using the headset, always replace
the rubber cover.

Version 4, 16.09.2005

A compatibility list of tested headsets can be found on the Internet at:
www.plantronics.com/productfinder.

14


First steps

What would you like to do next?
Now you have successfully started your Gigaset, you will probably want to
adapt it to your personal requirements. Use the following guide to quickly
locate the most important subjects.
If you are unfamiliar with menu-driven devices such as other Gigaset telephones you should first read the section entitled "Using the phone"
¢ page 16.

Information on ...
Eco Mode / Eco Mode+
Setting the ringer and volume
Setting the earpiece volume
Recording your own announcement for the answering
machine
Preparing the telephone for SMS reception
Operating the telephone on a PABX
Registering existing Gigaset handsets to a base station
Transferring directory entries from existing Gigaset
handsets to the new handset(s)

... is located here.

g
g
g
g
g
g
g
g

¢ page 45
¢ page 53
¢ page 52
¢ page 38
¢ page 31
¢ page 56
¢ page 46
¢ page 27

Version 4, 16.09.2005

If you have any queries about using your phone, please read the tips on
troubleshooting ("Questions and Answers" ¢ page 58) or contact our
customer service department (Customer Care ¢ page 58).

15


Using the phone

Using the phone
Control key
In the description below, the side of the control key (up,
down, right, left) that you have to press in the different
operating situations is marked in black, e.g. v for "press
on the right of the control key".
The control key has a number of different functions:

When the handset is in idle status
s
v
u
t

Open the directory.
Open the main menu.
Open the list of handsets.
Call up the menu for setting the handset's call volume
(¢ page 52), ringers (¢ page 53) and advisory tones
(¢ page 54).

In the main menu, in submenus and lists
t/s
v
u

Scroll up/down line by line.
Open the submenu or confirm the selection.
Go back one menu level or cancel.

In input fields
You can use the control key to move the cursor up t, down s, right v or
left u.

During an external call

Version 4, 16.09.2005

s
u
t

16

Open the directory.
Initiate internal consultation call and mute.
Adjust the loudspeaker volume for earpiece and speaker mode.


Using the phone

Display keys
The function of the display keys changes depending on the particular operating
situation. Example:

INT

SMS

1
2

1 Current display key functions are shown in the bottom display line.
2 Display keys

The most important display keys are:
§§§Options§§§
Open a context-dependent menu.
W
Delete key: backspace deletes one character at a time.
Î
Go back one menu level or cancel operation.
Ó
Copy number into directory.
Ÿ
Divert external call to answering machine (E495 only).
•
Open the last number redial list.

Keys on the keypad
c / Q / * etc.
Press the matching key on the handset.
~
Enter digits or letters.

Correcting incorrect entries
You can correct incorrect characters in the text by navigating to the incorrect
entry using the control key. You can then:
u Press X to delete the character to the left of the cursor
u Insert characters at the cursor position
u Overwrite the (flashing) character when entering the time and date etc.

Menu guidance
Your telephone's functions are accessed using a menu that has a number of levels.

Version 4, 16.09.2005

Main menu (first menu level)

¤ Press v with the handset in idle status to open the main menu.

The main menu functions are shown in the display as a list with colour icons
and names.

17


Using the phone
To access a function, i.e. to open the corresponding submenu (next menu
level):
¤ Navigate to the function using the control key q. Press the display key §OK§.

Submenus
The functions in the submenus are displayed as lists.
To access a function:
¤ Scroll to the function with the control key q and press §OK§.
Or:
¤ Enter the corresponding digit combination (¢ page 20).
Briefly press the end call key a once to return to the previous menu level/
cancel the operation.

Reverting to idle status
You can revert to idle status from anywhere in the menu as follows:
¤ Press and hold the end call key a.
Or:
¤ Do not press any key: after 2 minutes the display will automatically revert
to idle status.
Changes that you have not confirmed or saved by pressing §OK§, §Yes§, §Save§, §Send§
or Save Entry §OK§ will be lost.
An example of the display in idle status is shown on page 14.

Activating/deactivating the handset
a

With the phone in idle status, press and hold the end call key (confirmation tone) to switch off the handset.
Press and hold the end call key again to switch the handset on.

Activating/deactivating the keypad lock

Version 4, 16.09.2005

The keypad lock prevents any inadvertent use of the phone.
#
Press and hold the hash key in idle status to activate or deactivate
the keypad lock. You will hear the confirmation tone.
When the keypad lock is activated you will see the Ø icon on the display and
a message when you press a key.
The keypad lock is deactivated automatically if someone calls you. It is reactivated when the call is finished.

18


Using the phone

Illustration in the user guide
The operating steps are shown in abbreviated form.

Example
The illustration:
v ¢ Ð ¢ Date/Time
means:

¤ To display the main menu, press

the right side of the control key in
idle status.

î SMS
ê Sel. Services
ì Alarm Clock
í Add. Features
Ð Settings
Ý

OK

¤ Press the bottom of the control

key until Ð Settings is highlighted
by the bar.

Ý

OK

¤ Press the display key §OK§ to open
the submenu.

Date/Time is already indicated.
¤ Press the display key §OK§ to open
the function menu.
To enter the time and date, proceed
as described on page 13.

Settings
Date/Time
Audio Settings
Display
Handset

Version 4, 16.09.2005

Ý

OK

19

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / menuetree.fm / 19.02.2009

Menu tree

Menu tree
Instead of scrolling to locate a menu function, you can select a function more quickly by
opening the menu and keying in a digit combination (or shortcut).
Example: v 5 2 2
for "Set ringer for external calls".
With the telephone in idle status, press v (open main menu):
1

SMS î

You have activated an SMS mailbox (general or private) without a PIN

¢ page 31
¢ page 33
¢ page 31

1-1 New SMS
1-2 Incoming 0
1-3 Outgoing 0

You have activated an SMS mailbox with a PIN or 2-3 mailboxes
1-1 Mailbox

1-1-1 New SMS
1-1-2 Incoming 0
1-1-3 Outgoing 0

1-2 Mailbox 1
to Mailbox 2
1-4 Mailbox 3

1-2-1 New SMS
to
1-4-1
1-2-2 Incoming 0
to
1-4-2
1-2-3 Outgoing 0
to
1-4-3

1-6 Settings

1-6-1 Service Centres
1-6-2 SMS Mailboxes
1-6-3 Notify Number
1-6-4 Notify Type

2

Sel. Services ê

¢ page 24

2-3 Withhold No.
2-6 All Calls

2-6-1 Call Diversion
2-6-3 Call Waiting

2-7 Ringback Off

¢ page 46

Alarm Clock ì

4

Version 4, 16.09.2005

3

Add. Features í

4-3 Room Monitor

20

¢ page 24
¢ page 49

¢ page 31
¢ page 33
¢ page 31
¢ page 31
¢ page 33
¢ page 31
¢ page 35
¢ page 34
¢ page 34
¢ page 34
¢ page 25
¢ page 24

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / menuetree.fm / 19.02.2009

Menu tree
5

Settings Ð

5-1 Date/Time
5-2 Audio Settings

¢ page 13
5-2-1 Handset Volume
5-2-2 Ringer Settings
5-2-3 Advisory Tones
5-2-4 Silent Alert

5-3 Display

5-3-1 Screen Picture
5-3-2 Colour Scheme
5-3-3 Contrast
5-3-4 Backlight

5-4 Handset

5-4-1 Language
5-4-2 Auto Answer
5-4-3 Register H/Set
5-4-4 Reset Handset

5-5 Base

5-5-2 Music on hold
5-5-3 System PIN
5-5-4 Base Reset
5-5-5 Add. Features

¢ page 52
¢ page 53
¢ page 54
¢ page 54
¢ page 52
¢ page 51
¢ page 51
¢ page 52
¢ page 51
¢ page 52
¢ page 46
¢ page 54
¢ page 55
¢ page 55
¢ page 55
5-5-5-1 Dialling Mode
5-5-5-2 Recall
5-5-5-3 Repeater
Mode
5-5-5-4 Access Code
5-5-5-5 Listening In
5-5-5-7 Eco Mode
5-5-5-8 Eco Mode+

5-5-6 Preselection
5-5-7 Calls List Type
5-6 Voice Mail

5-6-1 Set Key 1
E495 base station only:
5-6-2 Ans Machine
5-6-3 Call Screening
5-6-4 Announcements

Version 4, 16.09.2005

5-6-5 Message Length
5-6-6 Recording Quality
5-6-7 Ring Delay

¢ page 30
¢ page 29
¢ page 44

¢ page 56
¢ page 56
¢ page 55
¢ page 56
¢ page 48
¢ page 45
¢ page 45

¢ page 38
¢ page 41
¢ page 38
¢ page 42
¢ page 42
¢ page 42
21

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / telefony.fm / 19.02.2009

Making calls

Making calls
Making an external call
External calls are calls using the public telephone network.
~c
Enter the number and press
the talk key.
Or:
c~
Press and hold the talk key
c and then enter the
number.
You can cancel the dialling operation with
the end call key a.
You are shown the duration of the call
while the call is in progress.

Please note
Dialling using the directory, the call-bycall list (¢ page 1/ ¢ page 26) or the
calls and last number redial list
(¢ page 29/¢ page 28) saves you
from having to re-enter numbers and
network provider prefixes ("call-by-call
numbers").

Ending a call

Version 4, 16.09.2005

a

22

Press the end call key.

Answering a call
The handset indicates an incoming call in
three ways: by ringing, by a display on the
screen and by the flashing speaker key
d.
You can accept the call by:
¤ Pressing the talk key c.
¤ Pressing the speaker key d.
¤ Gigaset E490: Press the display key
§Accept§.
¤ Gigaset E495: Press the display key
Ÿ to divert the call to the answering machine (¢ page 41).
If the handset is in the charging cradle and
the Auto Answer function is activated
(¢ page 52), the handset will take a call
automatically when you lift it out of the
cradle.
To deactivate the ringer, press the §Silence§
display key. You can take the call as long as
it is displayed on the screen.

Calling Line Identification
When you receive a call, the caller's
number is displayed on the screen if the
following conditions are met:
u Your network provider supports CLIP,
CLI.
– CLI (Calling Line Identification): the
caller's number is transmitted.
– CLIP (Calling Line Identification Presentation): the caller's number is displayed.
u You have arranged CLIP with your network provider.
u The caller has requested CLI from the
network provider.

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / telefony.fm / 19.02.2009

Making calls

Call display with CLIP/CLI
If the caller's number is saved in your
directory, the caller's name will also be displayed.

Å

1234567890
Accept

or

1

2

Silence

Å

1234567890

Ã

Gigaset E490

Speaker
In speaker mode, instead of holding the
handset to your ear you can put it down,
for example on the table in front of you.
This allows others to participate in the call.

Activating/deactivating speaker
Activating while dialling
~d

¤
Gigaset E495

1

2

Silence

1 Ringer icon
2 Number or name of caller

The following is displayed in place of the
number:
u External, if no number is transmitted.
u Withheld, if the caller has withheld Calling Line Identification (¢ page 24).
u Unavailable, if the caller has not
arranged Calling Line Identification.

Enter the number and press
the speaker key.
You should inform your caller before
you use the speaker function so that
they know someone else is listening.

Switching between earpiece and speaker
mode
d
Press the speaker key.
During a call and when listening to the
answering machine (Gigaset E495 only),
activate or deactivate speaker.
If you wish to place the handset in the
charging cradle during a call:
¤ Press and hold the speaker key d
while placing the handset in the base
station. If speaker key d does not
light up, press the key again.
For instructions on how to adjust the loudspeaker volume ¢ page 52.

Switch to on hold

Version 4, 16.09.2005

You can deactivate the microphone in
your handset during an external call.
The other party hears hold music.
u
Press left on the control key to
mute the handset.
”
Press the display key to switch
the microphone back on.
You can turn the hold music on and off
(¢ page 55).

23

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / TNet_Features_SAG.fm / 19.02.2009

Making calls using network services

Making calls using network
services

Call waiting during an
external call

Network services are functions that your
network provider makes available to you.
You have to request these services from
your network provider.
¤ If you require assistance, please contact your network provider.

If the function is activated during an
external call, you will hear a call waiting
tone to signal that another external caller
is trying to get through. If you have CLIP,
(¢ page 22) the number of the waiting
caller or the corresponding directory entry
is shown in the display.

Calling Line Identification

Activating/deactivating call waiting

Withhold Calling Line Identification once
(CLIR):
If you make a call, your number is shown
in the display of the call recipient if that
person has activated CLIP (¢ page 22).
If in certain instances you do not wish to
have your number displayed, you can
withhold your number for the next call
(CLIR).
v ¢ ê ¢ Withhold No.
~
Enter phone number.
c
Press the talk key.

Ringback
Initiating ringback
If the number you have called is engaged,
you can initiate ringback. As soon as the
line of the person you called is free, your
handset will ring.
You hear the busy tone.
§Options§ ¢ Ringback
a

Version 4, 16.09.2005

Cancelling ringback
You can cancel a ringback that has already
started.
v ¢ ê ¢ Ringback Off

24

v ¢ ê ¢ All Calls ¢ Call Waiting
Status:
Activate/deactivate.
§Send§
Press the display key.

Accepting a waiting call
You are making an external call and hear
the call waiting tone.
You have the following options:
§Options§ ¢ Accept waiting call
or
(only if the phone number or name of the
caller is displayed)
§Accept§
Once you have accepted the waiting
call you can switch between the two
callers ("call swap" ¢ page 25).

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / TNet_Features_SAG.fm / 19.02.2009

Making calls using network services

Call divert (CD)
When diverting a call, the call is forwarded
to another connection.
The following options are available:
u All Calls: Calls are diverted immediately.
No more calls are signalled on your
phone.
u No Answer: Calls are diverted if no one
accepts the call within several rings.
u When Busy: Calls are diverted when
your line is busy. Call is diverted without a call waiting tone.
v ¢ ê ¢ All Calls ¢ Call Diversion
¤ Change multiple line input:
When:
Select All Calls / No Answer / When Busy.
Phone #:
Press the display key §Edit§. Enter the
number to which the call is to be
diverted
Or:
Press s. Select number from the
directory and press §OK§.
Status:
Activate/deactivate call divert.
§Send§
a
After the announcement,
press the end call key.

Consultation call, call swap
These functions enable you to
u Call a second external caller (external
call)
u Switch between two calls (call swap)

~

Enter the second participant's
telephone number.
The phone number is dialled. You are connected to the second participant.
If the caller does not answer, select the
display key §End§ to return to the first participant.

Please note
You can also select the second participant's phone number from the directory (¢ page 28) or the calls list
(¢ page 29).

Ending a consultation call
§Options§

¢ End Active Call

You are reconnected to the first caller.

Call swap
You can speak to both callers one at a time
(call swap).
Precondition: You are conducting an
external call and have called a second participant (external call) or have accepted a
waiting call.
¤ Use q to swap between the participants.
The caller you are currently speaking to is
marked with the g icon.

End the current call

§Options§ ¢ End Active Call
You are re-connected to the waiting caller.

Version 4, 16.09.2005

External call
You can call a second external caller.
The first call is placed on hold.
During an external call:
§Ext.Call§
The previous call is placed on
hold. The other participant
hears an announcement.
25

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / direct_charges.fm / 19.02.2009

Using the directory and lists

The options are:
u Directory
u Call-by-call list
u Last number redial list
u SMS list
u Calls list
u Answering machine list
(Gigaset E495 only)
You create the directory and call-by-call
list for your own individual handset. You
can also send lists/entries to other handsets (¢ page 27).

Directory/call-by-call list
You can save a total of 150 entries in the
directory and call-by-call list.

Please note
For quick access to a number from the
directory (shortcut), you can assign
the number to a key.
In the directory you can save numbers
and corresponding names.
¤ With the handset in idle status, open
the directory by pressing the s key.
In the call-by-call list, you can save network provider prefixes ("call-by-call numbers").
¤ Open the call-by-call list in idle status
by pressing the C key.

Length of the entries

Version 4, 16.09.2005

Number:
Name:

26

max. 32 digits
max. 16 characters

Storing a number in the directory

s ¢ New Entry
Number
Enter the number.
Name
Enter name.
Speed Dial
Select key for shortcut.
¤ Save the changes.

Storing a number in the call-by-call list

C ¢ New Entry
Number
Enter the number.
Name
Enter name.

Order of directory entries
The directory entries are usually sorted in
alphabetical order. Spaces and digits take
first priority. The sort order is as follows:
1. Space
2. Digits (0–9)
3. Letters (alphabetical)
4. Other characters
To work round the alphabetical order of
the entries, insert a space or a digit in
front of the name. These entries will then
move to the beginning of the directory.

Selecting entries in the directory and
call-by-call list
s/ C

Open the directory or call-bycall list.
u Use s to scroll through the entries
until the required name is selected.
u Enter the first character of the name
and scroll to the entry using s if
required.



Dialling with the directory/call-by-call
list
s/ C
c

¢ s (select entry).

Press the talk key. The number
is dialled.

Managing directory/call-by-call entries
s/ C

¢ s (select entry).

Viewing entries
§View§

The entry is displayed.
Back with §OK§.

Editing entries
Press display keys one after the
other.
Carry out changes and save.

§View§ §Edit§

¤

Using other functions
The following functions can be selected
with q:
Display Number
To edit or add to a saved number, or to
save it as a new entry, press Ó
after the number is displayed.
Edit Entry
Edit selected entry.
Delete Entry
Delete selected entry.
VIP Entry (directory only)
Mark a directory entry as a VIP (Very
Important Person) and assign a specific
ringer to it. You can then recognise
important calls from the ringer.
Precondition: Calling Line Identification (¢ page 22).
Copy Entry
Send a single entry to a handset
(¢ page 27).
Version 4, 16.09.2005

§Options§

Delete List
Delete all entries in the directory/callby-call list.
Copy List
Send complete list to a handset
(¢ page 27).
Available Memory
Display the available entries in the
directory and call-by-call list
(¢ page 26).

Using shortcut keys

¤ Press and hold the required shortcut
key (¢ page 26).
Sending the directory/call-by-call list
to another handset
Preconditions:
u The sending and receiving handsets

must both be registered to the same
base station.
u The other handset and the base station
can send and receive directory entries.
s / C ¢ s (select entry) ¢ §Options§
(open menu) ¢ Copy Entry / Copy List
s
Select the internal number of
the receiving handset and
press §OK§.
You can transfer several individual entries
one after the other by responding §Yes§ to
the Copy next entry? prompt.
A successful transfer is confirmed by a
message and confirmation tone on the
receiving handset.

Please note:
u Entries with identical numbers are not

overwritten on the receiving handset.

u The transfer is cancelled if the phone

rings or if the memory of the receiving
handset is full.

27



Copying a displayed number to the
directory

Managing entries in the last number
redial list

Numbers displayed in a list, e.g. the calls
list or the last number redial list, in an SMS
or during a call can be copied to the directory.
A number is displayed:
§Options§ ¢ Copy to Directory
¤ Complete the entry, ¢ page 26.
Gigaset E495: The message playback is
interrupted during the number transfer
from the answering machine list.

c
s

Copying a number from the directory
There are many operating situations in
which you can open the directory, e.g. to
copy a number. Your handset need not be
in idle status.
¤ Depending on the operating situation,
open the directory with s or Ò
or ¨ Directory.
q
Select entry (¢ page 26).

Last number redial list
The last number redial list contains the
twenty numbers last dialled with the
handset (max. 32 digits). If a number is in
the directory or the call-by-call list, then
the appropriate name will be displayed.

Manual last number redial
c
s
c

Press the key briefly.
Select entry.
Press the talk key again.
The number is dialled.
When a name is displayed, you can display
the corresponding phone number by
pressing the display key §View§.

Press the key briefly.
Select entry.
§Options§
Open menu.
The following functions can be selected
with q:
Display Number (as in the directory,
page 27)
Copy to Directory
Copy an entry to the directory
(page 26).
Delete Entry (as in the directory, page 27)
Delete List (as in the directory, page 27)

Opening lists with the
message key
You can use the message key f to open
the following list selection:
u SMS list
If several mailboxes are set up
(¢ page 34), several lists are displayed.
u Answering machine list (Gigaset E495
only) or Network mailbox, if your network provider supports this function
and the fast access is set for the
(¢ page 44) network mailbox.
u Calls list
An advisory tone sounds as soon as a new
message arrives in a list. The f key
flashes (it goes off when the key is
pressed). In idle status, the display shows
an icon for the new message:
New message...

Ã

... in the answering machine list
(Gigaset E495 only) or on the
network mailbox

Á
Version 4, 16.09.2005

Icon

... in the calls list

À

... in the SMS list

The number of new entries is shown
beneath the corresponding icon.
28



List selection
If you press the message key f, only the
lists that contain messages are shown
(exception: network mailbox). Lists with
new messages are identified in bold:
Messages & Calls
Calls List:

(4)

Mailbox

(2)

SMS:

(1)

List entry
New messages are displayed at the top.
Example of list entries:
All Calls
Susi Sorglos
13.01.09 12:20
Louise Miller
22.01.09 11:15
Delete

Ý

Options

OK

Select a list with q. To open, press v
or §OK§.
If only one list contains entries, no list
selection is offered and the relevant list is
displayed immediately.

Incoming SMS message list
All received SMS messages are saved in
the incoming message list, page 32.

Calls list
Precondition: Calling Line Identification
(CLIP, page 22)
Depending on the type of list set, the calls
list contains
u Accepted calls ( ‰ )
u Missed calls
u Calls recorded by the answering
machine (Ã, Gigaset E495 only)
Depending on the type of list set, all numbers of the last 30 incoming calls are saved
or just the missed calls are saved.

Setting the calls list type

Version 4, 16.09.2005

‰

v ¢ Ð ¢ Base ¢ Calls List Type
Missed Calls / All Calls
Select and press §OK§ ( ‰ = on).
a
Press and hold (idle status).
The calls list entries are retained when you
change the list type.

u List type (in header)
u Status of entry

Bold: New entry
u Number or name of caller

You can add the caller's number to the
directory (¢ page 28).
u Date and time of call (if set, page 13)
u Type of entry:
– Accepted calls ( ‰ )
– Missed calls
– Calls recorded by the answering
machine (Ã, Gigaset E495 only)
Pressing the display key §Delete§ deletes the
highlighted entry.
After pressing the display key §Options§ you
can select more functions with q:
Copy to Directory
Copying a displayed number to the
directory.
Delete List
Delete complete list.
When you quit the calls list, all entries are
set to the status "old", i.e. the next time
you call the list up they will no longer be
shown in bold.

Answering machine list
(Gigaset E495 only)
You can use the answering machine list
to listen to the messages that are on the
answering machine.

29


Making cost-effective calls

Making cost-effective calls
Make phone calls through a network provider who offers particularly low-cost call
rates (call-by-call). You can manage the
numbers in the call-by-call list.

Linking call-by-call numbers
with one number
You can insert the dialling code of a network provider ahead of the number ("linking").
C
Open call-by-call list.
s
Select entry (call-by-call
number).
§Options§
Display Number
Select and press §OK§.
~
Enter number or select
number from the directory
(¢ page 28).
c
Press the talk key. Both numbers are dialled.

Automatic network provider
code (preselection)
You can store a call-by-call number (preselection number), which is automatically
placed in front of numbers when you dial
them.
In the "With Preselect" list, specify the
dialling codes or the first digits of the dialling codes with which you wish the preselection number to be used.
In the "Without Presel." list enter the
exception to the "With Preselect" list.

Example:
Version 4, 16.09.2005

Preselect no.

0999

With Preselect

08

Without Presel.

081
084

30

All numbers that start with 08 except for
081 and 084 are dialled with the preselection number 0999.
Phone number
07112345678
08912345678
08412345678

¢
¢
¢

Dialled number
07112345678
0999 08912345678
08412345678

Saving preselection numbers

v ¢ Ð ¢ Base ¢ Preselection
¢ Preselect No.
~
Enter or change the preselection number (call-by-call
number).
§Save§
a

Save or change entries in the
preselection lists
Each of the two lists can contain
20 entries, each with 6 digits.
Numbers may be prefixed according to the
country in the "with preselection" list.
This means, for example, that all national
calls or calls to the mobile network are
automatically linked to the preselection
number you have saved previously.
v ¢ Ð ¢ Base ¢ Preselection
¢ With Preselect / Without Presel.
s
Select entry.
§Edit§
~
Enter or edit first digits of
number.
§Save§
a

Temporarily cancelling preselection
c (press and hold) ¢ §Options§
¢ Aut Preselct off

Permanently deactivating preselection

¤ Delete the preselection number
(¢ page 30).

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / sms_BRD_neutral.fm / 19.02.2009

SMS (text messages)

SMS (text messages)
Your phone is supplied ready for sending
SMS messages immediately.

Preconditions:
u Calling Line Identification is enabled for

your phone line.

u Your network provider supports SMS on

the fixed line network (information on
this can be obtained from your network
provider).
u You are registered with your service
provider to send and receive SMS.
u To have reception you must be registered with your service provider. This is
completed automatically when you
send your first SMS.

Please note
If your phone is connected to a PABX,
please read page 36.

Sending an SMS
c
Or:

Press the talk key

§Options§


Send
SMS

~/s/ C

Select number with area code
(even if you are in that area)
from the directory or call-bycall list, or enter number
directly. For sending SMS to an
SMS mailbox: add the mailbox
ID to the end of the number.
Press the display key. The SMS
is sent.

§Send§

Please note
If you are interrupted by an external
call while writing an SMS, the text is
automatically saved in the draft message list.

Writing/sending an SMS

Draft message list

Writing an SMS

You can save an SMS in the draft message
list, and edit and send it later.

v¢î
Mailbox 2 Select mailbox if necessary
and press §OK§.
~
Enter mailbox PIN if necessary
and press §OK§.
New SMS Select and press §OK§.
~
Write an SMS.

Please note

u Instructions on entering text can be

found on page 63.

u An SMS can be up to 612 charac-

Version 4, 16.09.2005

ters.
If there are more than 160 characters, the SMS is sent as a linked SMS
(up to 4 SMS messages with
153 characters each).

Saving an SMS in the draft message list

¤ Writing an SMS (¢ page 31).

Save Entry Select and press §OK§.
§Options§

Opening the draft message list

v ¢ î ¢ or ~ (mailbox, mailbox
PIN) ¢ Outgoing
The first list entry is displayed, e.g.
1234567890
15.01.09 09:45

31


SMS (text messages)

Reading or deleting SMS messages

Receiving an SMS

q

All received SMS messages are saved in
the incoming message list. Linked SMS
messages are displayed as one message. If
this is too long or is not transferred completely, it is split into individual messages.
Since an SMS remains in the list even after
it has been read, you should regularly
delete SMS messages from the list.
The display tells you if the SMS memory is
full.

¤ Open the draft message list and then:
Select SMS.
§Read§
Press the display key. The
entry will be displayed. Scroll
line by line using q.
Or delete the SMS with
§Options§ ¢ Delete Entry ¢ §OK§.

Writing/changing an SMS

¤ You are reading an SMS in the draft

message list.
Open menu.
New SMS
Write a new SMS and then send
(¢ page 31) or save it.
Edit
Edit the text of the saved SMS and then
send it (¢ page 31).
Character Set
Text is shown in the selected character
set.

Please note

§Options§

Deleting draft message list

¤ Open the draft message list and then:
§Options§

Delete all
a

Open menu.
Select, press §OK§ and confirm
with §Yes§. The list is cleared.

Each incoming SMS is signalled by a
single ring (ringer as for external calls).
If you accept such a "call", the SMS will
be lost. To prevent this ring, suppress
the first ringer for all external calls
(¢ page 36).

Incoming message list
The incoming message list contains:
u All received SMS messages, starting
with the most recent.
u SMS messages that could not be sent
due to an error.
New SMS messages are signalled on all
Gigaset E49H handsets by the À icon in
the display, the flashing message key f
and an advisory tone.

Opening the incoming message list with
the f key

f
Press.
The incoming message list is indicated by
the mailbox name and the number of
entries (example):
SMS:

(2)

1
2

Version 4, 16.09.2005

1 Bold: number of new entries
Regular: number of read entries
2 Name of mailbox, here: general mailbox

If necessary select a mailbox and open list
by selecting §OK§ (if necessary enter mailbox PIN and confirm by pressing §OK§).
32


SMS (text messages)
The number and date of receipt are displayed in the entry list.
1234567890
15.01.09 09:45

Opening the incoming message list via the
SMS menu
v ¢ î ¢ or Select mailbox, enter
mailbox PIN ¢ Incoming

Deleting the incoming message list
All new and old SMS messages in the list
are deleted.
¤ Open the incoming message list.
§Options§
Open menu.
¤ To continue, see "Deleting draft message list", page 32.

Reading or deleting SMS messages

¤ Open the incoming message list, then:

q

Select SMS.
§Read§
entry will be displayed. Scroll
line by line using q.
Or delete the SMS with
§Options§ ¢ Delete Entry ¢ §OK§.
After you have read a new SMS, it is given
the status "Old" (is no longer shown in
bold).

Changing the character set

¤ Reading an SMS

Character Set
Text is shown in the selected character
set.

Version 4, 16.09.2005

§Options§

Replying to or forwarding text
messages

¤ Reading an SMS

§Options§
Reply
Write and send a reply SMS directly
(¢ page 31).
Edit
Edit the text in the SMS and then send
it (¢ page 31).
Forward
Forward the SMS to another number
(¢ page 31).

Copying the number to the directory
Copying the sender's number

¤ Open the incoming message list and
select entry (¢ page 32).
§Options§ ¢ Copy to Directory
¤ Complete the entry ¢ page 28.
Please note
An attached mailbox identifier is
added to the directory.

Copying/dialling numbers from an
SMS text

¤ Read the SMS and scroll to the tele-

phone number.
The digits are highlighted.
Ó
Complete the entry ¢ page 28.
Or:
c
Press the talk key to dial the
number.
If you wish to use the number to send an
SMS:
¤ Save the number with the local area
code (dialling code) in the directory.

33


SMS (text messages)

Notification by SMS

SMS mailboxes

You can be notified about missed calls or
new answering machine messages
(Gigaset E495 only) via SMS.
Precondition: For missed calls, the caller's
number (CLI) must have been transmitted.
Notification is sent to your mobile phone
or another phone with SMS functionality.
You only need to save the phone number
to which notification should be sent (notification number) and set the notification
type.

The general mailbox is the default setting. Anyone can access this mailbox and
it cannot be protected by a PIN. You can
additionally set up three personal mailboxes and protect these with a PIN. Each
mailbox is identified by a name and a
"mailbox ID" (a kind of extension number).

Saving the notification number

v ¢ î ¢ Settings ¢ Notify Number
~
Enter the number to which the
SMS should be sent.
§Save§

Please note
Do not enter your own fixed line network number for the notification of
missed calls. This can lead to chargeable endless looping.

Setting the notification type

Version 4, 16.09.2005

v ¢ î ¢ Settings ¢ Notify Type
¤ Change multiple line input if necessary:
Missed Calls
Select On if you require SMS notification.
Ans Machine (Gigaset E495 only)
Select On if you require SMS notification.

34

Please note:
u If you operate a number of devices

(base stations) with SMS functionality
on a single phone line, then each SMS
mailbox ID may only occur once. In this
case you must also change the preset
ID of the general mailbox ("0").
u You can only use personal mailboxes if
your service provider supports this
function. You can tell whether this is
the case by the addition of a star (*) to
the number of a (preset) SMS centre.
u If you have forgotten your mailbox PIN,
you can reset it by restoring the base
station's default settings. This will
delete all SMS messages from all
mailboxes.

Setting up and changing a personal
mailbox
Setting up a personal mailbox

v ¢ î ¢ Settings ¢ SMS Mailboxes
s
Select mailbox, e.g. Mailbox 2
and press §OK§.
On/Off
Activate or deactivate mailbox.
ID
Select mailbox ID (0–9). You can only
select the available numbers.
Protection
Activate/deactivate PIN protection.
PIN
If necessary, enter 4-digit PIN.


SMS (text messages)
Active mailboxes are marked with ‰ in
the mailbox list. They are shown in the
SMS list and can, if necessary, be displayed
by pressing the message key f.

Deactivating a mailbox

¤ Set On/Off to Off. Confirm message with
§Yes§ if necessary.

All SMS messages saved in this mailbox
will be deleted.

Deactivating PIN protection

¤ Set Protection to Off.

The mailbox PIN is reset to "0000".

Changing the name of a mailbox

¢ s (Select mailbox)
§Edit§
~
Enter new name.
§Save§
a

Changing a mailbox's PIN and ID

¢ s (Select mailbox)
~
Enter mailbox PIN if necessary
and press §OK§.
¤ Set ID, Protection and PIN (¢ page 34).

Sending an SMS to a personal mailbox

Version 4, 16.09.2005

To send an SMS to a personal mailbox, the
sender must know your ID and enter it
after your number.
¤ You can send your SMS contact an SMS
via your personal mailbox.
Your SMS contact will receive your SMS
number with current ID and can save it in
their directory. If the ID is invalid, the SMS
will not be delivered.

Setting SMS centres
SMS messages are exchanged between
SMS centres operated by service providers. You must enter the SMS centre
through which you wish to send and
receive SMS messages into your phone.
You can receive SMS messages from every
SMS centre that is entered, provided you
have registered with your service provider.
Your SMS messages are sent through the
SMS centre that is entered as the active
send service centre (¢ page 35). Only
one SMS centre can be the active send
service centre at any one time.
If no SMS service centre is entered,
the SMS menu only contains the entry
Settings. Enter an SMS Service Centre
(¢ page 35).

Entering/changing SMS centres

¤ You should find out about the services

and special functions offered by your
service provider before you make a
new application and/or before you
delete pre-configured call numbers.
v ¢ î ¢ Settings ¢ Service Centres
s
Select SMS centre (e.g. Service
Centr. 1) and press §OK§.
Active send
Select Yes if SMS messages are to be
sent via the SMS centre.
SMS
Press the display key §Edit§. Enter the
number of the SMS service and insert a
star if your service provider supports
personal mailboxes.
§Save§

Please note
Ask your service provider for details
on how to enter service numbers if you
wish to use personal mailboxes
(precondition: your service provider
supports this function).

35


SMS (text messages)

Sending an SMS via another SMS
centre

¤ Activate the SMS centre (2 to 4) as the
active send service centre.

¤ Send the SMS.

SMS on a PABX
u You can only receive an SMS when the

Version 4, 16.09.2005

Calling Line Identification is forwarded to the extension of the PABX
(CLIP). The CLIP evaluation of the
phone number for the SMS centre takes
place in your Gigaset.
u Depending on your PABX, you may
have to add the access code (external
line prefix) before the number of the
SMS centre.
If in doubt, test your PABX, e.g. by
sending an SMS to your own number:
once with and once without the access
code.
u When you send SMS messages, your
sender number may be sent without
your extension number. In this case the
recipient cannot reply to you directly.
Sending and receiving SMS messages on
ISDN PABXs is only possible via the MSN
number assigned to your base station.

36

Activating/deactivating first
ringer muting
v
Open menu.
55O
O
Press keys.
Make the first ring audible.
Q §OK§
Or:

§OK§
Mute the first ring.

Activating/deactivating SMS
function
If you deactivate the SMS function, you
cannot send or receive any SMS messages
with your phone.
The settings you have made for sending
and receiving SMS messages (e.g. the
numbers of the SMS centres) and the
entries in the incoming and draft message
lists are saved even after deactivation.
v
Open menu.
55O2L
Enter the digits.
Deactivate SMS function.
Q §OK§
Or:

§OK§
Activate SMS function (default
setting).


SMS (text messages)

SMS troubleshooting

You have stopped receiving SMS messages.

Error codes when sending

1. You have changed the ID of your mailbox.
Give your SMS contacts your new ID or
page 35).
undo the change (

E0 Calling Line Identification permanently
withheld (CLIR) or Calling Line Identification not activated.
FE Error occurred during SMS transfer.

¥

¢

2. You have not activated your mailbox.
Activate your mailbox (
page 35).

¥

¢

FD Connection to SMS centre failed; see selfhelp.

3. Call divert is activated with All Calls or call
divert for All Calls is activated for the network mailbox.
Change the call divert.

Self-help with errors

The SMS is played back.

The following table lists error situations
and possible causes and provides notes on
troubleshooting.

1. The "display call number" service is not activated.
Ask your service provider to activate this
function (chargeable).

SMS function is not available.
The memory is full or the SMS function on
the base station is being used by another
handset.
Delete SMS messages you no longer
require or send the SMS later.

¥

You cannot send messages.
1. You have not requested the CLIP service
(Calling Line Identification Presentation).
Ask your service provider to enable this
service.

¥

2. SMS transmission has been interrupted
(e.g. by a call).
Re-send the SMS.

¥

3. The network provider does not support this
feature.
4. No number or an invalid number is entered
for the SMS centre set as the active send
service centre.
Enter the number (
page 35).

¥

¢

¥
¥

2. Your mobile phone operator and your fixed
line network SMS service provider have not
agreed on a co-operation.
Obtain information from your fixed line
network SMS service provider.

¥

3. Your terminal has been recorded by your
SMS provider as having no fixed line network SMS functionality, i.e. you are no
longer registered with the provider.
Have the device (re-)registered to
receive SMS messages.

¥

Messages are only received during the day.
The terminal is recorded in your SMS provider's database as having no fixed line network SMS functionality, i.e. you are not registered with the provider.
Obtain information from your fixed line
network SMS service provider.
Have the device (re-)registered to
receive SMS messages.

¥
¥

You receive an incomplete SMS.
1. Your phone's memory is full.
Delete old SMS messages (

¥

¢ page 33).

Version 4, 16.09.2005

2. The service provider has not yet sent the
rest of the SMS.

37

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / answering_m.fm / 19.02.2009

Operating the answering machine of the Gigaset E495 base station

Operating the answering
machine of the
Gigaset E495 base station
You can operate the answering machine
that is integrated in the base station via
the handset or via remote operation
(other phone/mobile phone). You can only
record your own announcement messages using the handset.

Announcement mode
You can use the answering machine in
two different modes.
u In Ans. & Record mode, the caller hears
the announcement and can then leaves
a message.
u In Announce Only mode, the caller hears
your announcement but cannot leave a
message.

Operation via the handset
The handset loudspeaker activates automatically if you receive an acoustic
prompt or message while operating. You
can switch it off with the speaker key d.

Version 4, 16.09.2005

Activating/deactivating the answering
machine

v ¢ Ð ¢ Voice Mail ¢ Ans Machine
( ‰ = on)
When you switch the answering machine
on, the remaining memory time is
announced. If the time has not yet been
set (¢ page 13), an appropriate
announcement is made. The × icon
appears in the display.
The phone is supplied with pre-recorded
announcements for answer and record
mode and for answer only mode. If a personal announcement has not been
recorded, the relevant pre-recorded
announcement is used.
38

Recording announcement/announce
only

v ¢ Ð ¢ Voice Mail ¢ Announcements
¢ Record Announce / Record Anc Only
§OK§
Press the display key to start
the recording.
You hear the ready tone (short tone).
¤ Now speak your announcement
(at least 3 secs.).
§End§
Press the display key to end
the recording.
Cancel the recording with a or ”.
Restart the recording with §OK§.
After recording, the announcement is
played back for you to check. You can rerecord the announcement with §New§.

Please note:
u Recording ends automatically if the

maximum recording time of 3 minutes
is exceeded or there is a break in
speech for more than 2 seconds.
u If you cancel the recording, the prerecorded announcement will be used
again.
u If the answering machine's memory is
full, it will switch to Announce Only
mode.
¤ Delete old messages and the
answering machine will automatically switch back to Ans. & Record
mode. Repeat recording if required.



Playing back announcements

¢ Play Announce / Play Anc Only
If you have not recorded a personal
announcement, the relevant pre-recorded
announcement is played.
Record a new announcement while playing back the announcement:
§New§
u If the answering machine's memory is
full, it will switch to Announce Only
mode.
¤ Delete old messages and the
answering machine will automatically switch back to Ans. & Record
mode. Repeat recording if required.

Deleting announcements/announce
only

v ¢ Ð ¢ Voice Mail
¢ Announcements ¢ Del Announce /
Del Anc Only
§Yes§
Press the display key to confirm the prompt.
a
Once you have deleted your announcement, the relevant pre-recorded
announcement will be used again.

Selecting announcement mode

Version 4, 16.09.2005

You can choose between Ans. & Record and
Announce Only.
v ¢ Ð ¢ Voice Mail
¢ Announcements ¢ Set Ans. Mode
¢ Ans. & Record / Announce Only ( ‰ = on)
a
The selected mode is saved even after the
answering machine is deactivated.

¤ Delete old messages.

The answering machine automatically
switches back to the set mode once deletion is complete. You can then reselect the
required recording mode.

Setting "Ans Mode Time" in "Answer &
Record" or "Announce Only" mode
You can use the Ans Mode Time setting to
change over the announcement mode for
a specific period.
Example: Ans. & Record mode is set. If you
activate Ans Mode Time and set a period
(e.g. 18:00 to 08:00) the answering
machine switches to Announce Only mode
for this period. Outside this period (08:01
to 17:59), Ans. & Record mode is active.
¢ Set Ans. Mode ¢ Ans Mode Time
( ‰ = on)
From
Enter hours/minutes for the start of the
period in 4-digit format.
Until
Enter hours/minutes for the end of the
period in 4-digit format.
Activation
Select On or Off.
¤ Save changes with §Save§.
If the messages memory is full and Activation On has been selected, saving is interrupted and you will receive an instruction
to delete old messages.
¤ Delete old messages and repeat the setting.
As soon as you change the announcement
mode (¢ page 39), the Ans Mode Time
function is automatically deactivated.

If the memory for messages is full in Ans.
& Record mode, the answering machine
will switch to the Announce Only mode and
you will receive an instruction to delete
old messages.
39



Playing back messages

s or 3

The date and time of each message is
logged (provided this has been set,
page 13) and displayed during the playback. If Calling Line Identification is activated, the caller's number is displayed. If
the caller's number is saved in the directory, their name is displayed.

Marking a message as "new"

Playing back new messages
New messages that have not yet been
heard are indicated by the Ã icon in the
display and by the f key flashing on the
handset.
f
Press the message key.
Ans M.
An announcement informs you if there are
new or old messages.
If there are new messages, playback then
begins with the first new message. After
the last new message you will hear the
end tone and an announcement about
how much recording time remains.
If the message has been saved with the
date and time, you will hear an appropriate announcement before playback
begins.

Playing back old messages
You can listen to old message if there are
no more new messages. Begin playback as
described under "Playing back new messages".
After the entry time and date have been
played back (after approx. 3 seconds) a
new message assumes the status "old".

Version 4, 16.09.2005

Stopping and controlling playback
During message playback:
2
Pause playback. Press 2
again to resume.
t or

Return to the start of the current message.
Press twice to go back to the
previous message.
40

Skip to the next message.
Press twice to skip to the next
but one message.
If playback is interrupted for over a
minute, the answering machine returns to
idle status.
A previously played back "old" message is
displayed as a "new" message again.
During message playback:
*
Press the star key.
An announcement informs you of the
message's new status.
Or:
§Options§

Open menu.

Mark as New

Playback of the current message is cancelled. Playback of next message starts, if
applicable.
The f key on the handset flashes.

Copying the phone number of a message
to the directory
See "Copying a displayed number to the
directory", page 28.

Deleting messages
You can either delete all old messages
together or individually.

Deleting all old messages
During playback or pause:
§Options§
Del All Old Msgs
§Yes§
Press the display key to confirm the prompt.

Deleting individual old messages
During playback or pause:
§Delete§



Picking up a call from the answering
machine
You can pick up a call while the answering
machine is recording or is being operated
via remote operation:
c / §Accept§
Press the talk or display key.
Recording stops and you can speak to the
caller.
If 2 seconds of the call have already been
recorded when you pick it up, the call will
be displayed as a new message. The f
key on the handset flashes.
You can answer the call even if it is not signalled on the handset.

Diverting an external call to the
answering machine
You can divert an incoming external call to
the answering machine even if it is deactivated.
Precondition: Sufficient memory space is
available on the answering machine.
An external call is signalled on the handset:
Ÿ
The answering machine immediately
starts in recording mode and records the
call. The set time for ring delay
(¢ page 42) is ignored.

Activating/deactivating two-way
record
You can record an external call with the
answering machine.
¤ Inform the caller that the call is being
recorded.
§Options§
Open menu.

Two-way Record
Two-way record is indicated on the display
by an advisory text and is added to the
answering machine list as a new message.
§End§
Press the display key to stop
two-way record.
The maximum recording time depends on
the memory available on the answering
machine. If the memory is full you will
hear an end tone, the recording is
aborted, and the call recorded up to that
point is listed in the answering machine
list as a new message. If the answering
machine was in Ans. & Record mode, it will
switch to Announce Only mode. You will
receive an instruction to delete old messages.
¤ Delete old messages.
The answering machine automatically
switches back to the set mode once deletion is complete.

Activating/deactivating call
screening
During recording of a message you can
screen a call via the loudspeaker of registered handsets.

Permanently activating/deactivating
call screening

v ¢ Ð ¢ Voice Mail ¢ Call Screening
¢ Handset ( ‰ = on)
a
You can switch off the Call Screening function on the handset during the recording.

Deactivating call screening for the
current recording

Version 4, 16.09.2005

§Silence§


41



Setting up the answering
machine
The answering machine has already been
preset at the factory. Make individual settings using the handset.

Ring delay/cost saving function for
remote operation
You can set when you want the answering
machine to accept a call.
The options are: No delay, after 10 sec., 18
sec. or 30 sec. and the cost-saving setting
Automatic.
In Automatic mode, the following applies
for ring delay:
u If there are no new messages, the
answering machine answers a call after
18 seconds.
u If new messages are present, the
answering machine accepts a call after
10 seconds.
When operating remotely you can tell
after approx. 15 seconds that there are no
new messages (otherwise the answering
machine would already have accepted
your call). There will be no call charges if
you hang up now.
v ¢ Ð ¢ Voice Mail ¢ Ring Delay
r
Select No delay / 10 sec. / 18
sec. / 30 sec. / Automatic.
§Save§
a

Please note:

Version 4, 16.09.2005

You can configure your telephone so that
the first ring is suppressed on all calls
(¢ page 36). The time set for ring delay
therefore does not indicate how long the
phone rings before the answering
machine accepts the call.

42

Setting the recording time
You can set the maximum recording time
of a message. The options are: 1, 2, 3 mins
or Maximum.
v ¢ Ð ¢ Voice Mail ¢ Message Length
r
Select the recording time.
§Save§

Setting the recording quality
Set the quality you require for your recordings. The options are: Long Play, High,
Excellent. If the quality is higher, the maximum recording time is reduced.
v ¢ Ð ¢ Voice Mail ¢ Recording
Quality
r
Select the recording quality.
§Save§

Resetting fast access for the
answering machine using key 1
The integrated answering machine has
already been preset for fast access at the
factory. However, if you have set the network mailbox for fast access (¢ page 44),
you can reset this setting.
v ¢ Ð ¢ Voice Mail ¢ Set Key 1
Answer Machine / Network Mailb.
a
After you have selected the network mailbox or the answering machine, press and
hold key
. You will be connected
directly.
The setting for fast access applies to all
Gigaset E49H handsets.



Operating when on the move
(remote operation)
You can check and activate your answering machine from any other telephone
(hotel, pay phone etc.), or initiate ringback from the answering machine with an
SMS.

Preconditions:
u You have set a system PIN other than

0000 (¢ page 55).

u The phone you are using for remote

operation has tone dialling (DTMF), i.e.
you hear different tones when you
press the keys. Alternatively, you can
use a code transmitter (available from
your mobile phone retailer).

Calling the answering machine and
playing back messages
~
9~

Version 4, 16.09.2005

Dial your own number.
When you hear your
announcement, press 9 and
enter the system PIN.
You will be informed whether any new
messages have been recorded. The messages are now played back. You can now
operate the answering machine with the
keypad.
The following keys are used for operation:
A
To return to the start of the
current message.
Press twice to go back to the
previous message.
B
Stop playback. Press again to
resume.
3
Go to the next message.
:
Mark message as "new".
0
Delete current message.

Activating the answering machine

¤ Phone home and let the phone ring

until you hear: "Please enter PIN".
~
Enter system PIN.
Your answering machine is activated. It
tells you how much memory time is left.
The messages are now played back.
The answering machine cannot be deactivated remotely.

Initiating ringback from the answering
machine with SMS and listening to
messages
Precondition: You must have stored a
notification number (¢ page 34).
You can use the telephone (mobile phone
or any other device with SMS functionality) for which you have stored the notification number in your phone to send an SMS
to your answering machine when you are
away from home. It will then call you back.
The message playback begins after the
ring delay when you press any key.
The SMS must contain the following:
*<System PIN>*<Ringback number>*
The ringback number is optional.
Examples:
*4711* or *4711*089123456*
If a ringback number is entered, it is
dialled; otherwise the notification number
is dialled.
You can now operate the answering
machine via the keypad, as described in
the previous sections.

43

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / T-NetBox_SAG.fm / 19.02.2009

Using the network mailbox

Using the network mailbox
The network mailbox is your network provider's answering machine within the network. You cannot use the network mailbox unless you have requested it from
your network provider.

Configuring fast access for the
network mailbox
With fast access, you can dial the network
mailbox or the integrated answering
machine (Gigaset E495 only) directly.
Gigaset E490: Fast access is preset for the
network mailbox. You only need to enter
the number of the network mailbox.
Gigaset E495: The integrated answering
machine is preset for fast access. You can
configure the network mailbox instead.
Ask your network provider about this.

Configuring fast access for the network
mailbox and entering the network mailbox
number

v ¢ Ð ¢ Voice Mail ¢ Set Key 1
Network Mailb.
~
Enter the number for the network mailbox.
§Save§
a
The setting for fast access applies to all
Gigaset E49H handsets.

Calling the network mailbox

Version 4, 16.09.2005

d

44

Press and hold. You are connected straight to the network
mailbox.
Press speaker key d if
required. You will hear the network mailbox announcement.

Viewing the network mailbox
message
When a message is recorded, you receive
a call from the network mailbox. If you
have requested Calling Line Identification,
the network mailbox number will be displayed. If you take the call, the new messages are played back. If you do not take
the call, the network mailbox number will
be saved in the missed calls list and the
message key flashes (¢ page 28).

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / registr_sett.fm / 19.02.2009

ECO DECT

ECO DECT
You are helping to protect the environment with your Gigaset E490/E495.

Reduced energy consumption
Your telephone has a power-saving
adapter plug and uses less power.

Status displays
Display icon
Ð i Ñ Ò
| (flashes)
½

Eco Mode enabled

¼

Eco Mode+ enabled
(displayed instead of
the reception strength
icon when in idle status)

Reduced transmission power
The transmission power of your telephone
is automatically reduced depending on
the distance to the base station.
You can reduce the transmission power of
the handset and base station even further
by using Eco Mode or Eco Mode+:
u Eco Mode
80% transmission power reduction in
standby and talk mode.
u Eco Mode+
100% transmission power deactivation
during standby mode.
Eco Mode / Eco Mode+ can be activated/
deactivated independently of each other
and also work with multiple handsets.

Activate/deactivate Eco Mode /
Eco Mode+ :

Version 4, 16.09.2005

v ¢ Ð ¢ Base ¢ Add. Features
¢ Eco Mode / Eco Mode+
§OK§
Press the display key
( ‰ = activated).

Reception strength:
– good to poor
– no reception

Please note

u With Eco Mode+ enabled, press

u

u

u
u

and hold the talk key c to check
that the base station can be
reached. You will hear the ringing
tone if the base station can be
reached.
When Eco Mode+ is enabled:
– call setup will be delayed by
approx. 2 seconds.
– handset standby time will be
reduced by approx. 50%.
Registering handsets that do not
support Eco Mode+ will cause the
mode to be deactivated on the base
station and all other handsets.
Activating Eco Mode reduces the
range of the base station.
Eco Mode / Eco Mode+ and
repeater support (¢ page 55) cancel each other out, i.e. you cannot
use Eco Mode and Eco Mode+ when
using a repeater.

45


Setting the alarm clock

Setting the alarm clock

Using several handsets

Precondition: The date and time have
already been set (¢ page 13).

Registering handsets

Activating/deactivating the alarm
clock and setting the wake-up time

You can register up to six handsets to your
base station.

v¢ì
Activation
Select On or Off.
Time
Enter the wake-up time in 4-digit format.
Melody:
Select melody.
Volume:
Set the volume (1–6).
You will see the ì icon.
A wake-up call with selected ringer melody (¢ page 53) is signalled on the handset. The wake-up call sounds for 60 seconds. ì is shown in the display. If no key
is pressed, the wake-up call is repeated
twice at five minute intervals and then
turned off.
During a call, the wake-up call is only signalled by a short tone.

Version 4, 16.09.2005

Deactivating the wake-up call/
repeating after a pause (snooze mode)
Precondition: A wake-up call is sounding.
§OFF§
wake-up call is deactivated.
or
§Snooze§
Press the display key or any
key. The wake-up call is deactivated and then repeated after
5 minutes. After the second
repetition the wake-up call is
deactivated completely.

46

Manual registration of Gigaset E49H to
Gigaset E490/E495
You must activate manual registration of
the handset on both the handset and the
base station.
Once it has been registered, the handset
returns to idle status. The handset's internal number is shown in the display e.g. INT
1. If not, repeat the procedure.

On the handset

v ¢ Ð ¢ Handset ¢ Register H/Set
~
Enter the system PIN of the
base station (the default is
0000) and press §OK§. Base 1
flashes in the display.

On the base station
Within 60 seconds press and hold the registration/paging key on the base station
(page 1) (approx. 3 seconds).

Registering other handsets
You can register other Gigaset handsets
and handsets for other devices with GAP
functionality as follows.

On the handset

¤ Start to register the handset as
described in its user guide.

On the base station
Press and hold the registration/paging key
on the base station (page 1) (approx. 3
sec.).



De-registering handsets
You can de-register any other registered
handset from any registered Gigaset E49H
handset.
u
Open list of internal participants.
The handset you are currently
using is indicated by <.
s
Select the internal participant
you wish to deregister.
§Options§
Open menu.
De-reg. H/Set No.
~
Enter the current system PIN
and press §OK§.
§Yes§

Locating a handset ("paging")
You can locate your handset using the
base station.
¤ Briefly press the registration/paging
key on the base station (page 1).
¤ All handsets will ring simultaneously
("paging"), even if the ringers are deactivated.

Ending paging

¤ Briefly press the registration/paging

key on the base station or press the talk
key c on the handset.

Making internal calls
Internal calls to other handsets registered
to the same base station are free of
charge.

s
c

Select handset.
Press the talk key.

Calling all handsets ("group call")
u
*

Initiate internal call.
Press the star key. All handsets
are called.

Ending a call
a


Transferring a call to another handset
You can transfer an external call to
another handset (connect).
u
The external participant hears
hold music if activated
(¢ page 55).
s
Select a handset or Call All and
press §OK§.
When the internal participant answers:
¤ If necessary announce the external call.
a
The external call is transferred to the other
handset.
If the internal participant does not answer
or the line is busy, press the display key
§End§ to return to the external call.
When transferring a call you can also press
the end call key a before the internal
participant answers.
Then, if the internal participant does not
answer or the line is busy, the call will
automatically return to you (the display
will show Recall).

Calling a specific handset

Version 4, 16.09.2005

u
~
Or:
u

Enter the number of the handset.
47



Internal consultation/conference calls

Rejecting the external call

When you are conducting an external
call, you can call an internal participant at
the same time for consultation or hold a
conference call between all 3 participants.
You are conducting an external call:
u
The external participant hears
hold music if activated
(¢ page 55).
s
Select handset and press §OK§.
You are connected to the internal participant.
either:
§End§
You are reconnected with the
external participant.
Or:
§Conference§ Press the display key.
All 3 participants are connected with each other.

§Reject§
The call waiting tone is turned off. You
remain connected with the internal participant. The ringer can still be heard on
other registered handsets.

Ending a conference call
a
If an internal participant presses the end
call key a, the other handset remains
connected to the external participant.

Accepting/rejecting call waiting
If you receive an external call during an
internal call, you will hear the call waiting
tone (short tone). With Calling Line Identification, the caller's number will appear in
the display.

Ending an internal call, accepting an
external call
The internal call is ended. You are connected to the external caller.

Version 4, 16.09.2005

§Accept§

48

Listening in to an external call
Precondition: The Listening In function
must be activated.
You are conducting an external call. An
internal participant can listen in on this
call and take part in the conversation. All
the participants are made aware of the
"listening in" by a signal tone.

Activating/deactivating listening in

¢ Listening In
Press §OK§ to activate/deactivate the function ( ‰ = on).
a

Listening in
The line is engaged with an external call.
Your screen will display information to
that effect. You want to listen in to the
external call.
c
Press and hold the talk key.
You can listen in to the call. All participants
hear a signal tone. During this time, this
handset displays the Conference message
and it is not possible to dial another
number from this handset.

Ending listening in
a
All participants hear a signal tone.
If the first internal participant presses the
end call key a, the handset that has "listened in" remains connected to the external participant.


Using a handset as a room monitor

Changing the name of a handset
The names "INT 1", "INT 2" etc. are
assigned automatically on registration.
You can change these names. The name
must be no more than 10 characters. The
changed name is displayed in every handset's list.
u
Open the list of handsets. Your
own handset is indicated by <.
s
Select handset.
§Edit§
~
Enter name.
§Save§

Version 4, 16.09.2005

Changing a handset's internal
number
A handset is automatically assigned the
lowest free number when it is registered.
If all slots are occupied, number 6 is overwritten if this handset is in idle status. You
can change the internal number of all registered handsets (1–6).
u
Open the list of handsets. Your
own handset is indicated by <.
§Options§
Open menu.
Edit H/Set No.
Select and press §OK§. The list of
handsets is displayed.
s
The current number flashes.
Select a handset.
~
Enter the new internal number
(1–6). The handset's old
number is overwritten.
§Save§
Press the display key to save
the input.
a
You will hear the error tone (descending
tone sequence) if you assign an internal
number twice.
¤ Repeat the procedure with a free
number.

Using a handset as a
room monitor
If the room monitor is activated, a previously saved destination number is called
as soon as a set noise level is reached. You
can save an internal or external number in
your handset as the destination number.
The room monitor call to an external
number stops after around 90 seconds.
The room monitor call to an internal
number (handset) stops after approx. 3
minutes (depending on the base station).
When the room monitor is activated, all
keys are locked except the end call key.
The handset's speaker is muted.
When the room monitor is activated,
incoming calls to the handset are indicated without a ringer and are only
shown on the screen. The display and keypad are not illuminated and advisory
tones are also turned off.
If you accept an incoming call, the room
monitor is suspended for the duration of
the call, but the function remains activated.
If you deactivate then reactivate the handset, the room monitor remains activated.

49


Using a handset as a room monitor

Warning

u You should always check the

operation of the room monitor
before use. For example, test its
sensitivity. Check the connection
if you are diverting the room
monitor to an outside number.
u When the function is switched on,
the handset's operating time is considerably reduced. If necessary,
place the handset in the charging
cradle. This ensures that the batteries do not run down.
u Ideally the handset should be positioned 1 to 2 metres away from the
baby. The microphone must be
directed towards the baby.
u The connection to which the room
monitor is diverted must not be
blocked by an activated answering
machine.

Activating the room monitor and
entering the destination number

Version 4, 16.09.2005

v ¢ í ¢ Room Monitor
Room M.
Select On to activate.
Call to
Press the display key §Edit§ and enter destination number.
External number: Select number from
the directory or enter directly. Only the
last 4 digits are displayed.
Internal number: §INT§ ¢ s (select
handset or Call All if all registered handsets are to be called) ¢ §OK§.
Store number with §Save§.
Level
Set noise level sensitivity (Low or High).
¤ Press §Save§ to save the settings.

50

Changing a set external destination
number

s
Scroll to the Call to line.
§Edit§
X
Delete existing number.
¤ Enter number as described in "Activating the room monitor and entering the
destination number" (¢ page 50).

Changing a set internal destination
number

s
Scroll to the Call to line.
§Delete§
§Edit§
¤ Enter number as described in "Activating the room monitor and entering the
destination number" (¢ page 50).

Deactivating the room monitor
remotely
Preconditions: The phone must support
tone dialling and the room monitor should
be set for an external destination number.
¤ Accept the call from the room monitor
and press keys 9 ;.
The room monitor function will deactivate
after the call ends. There will be no further
room monitor calls. The other room monitor settings (e.g. no ringer) on the handset
will remain activated until you press the
display key §OFF§ on the handset.
To reactivate the room function with the
same phone number:
¤ Turn on the activation again and save
with §Save§ (¢ page 50).


Handset settings

Handset settings
Your handset is preconfigured, but you
can change the settings to suit your individual requirements.

Quick access to functions
The display keys have a function preset by
default. You can change the assignment.
To start the function, you then simply
need to press the button.

Changing display key assignments

¤ Press and hold the left or right side of

the display key.
The list of possible key assignments is
opened. The following can be selected:
INT
Internal calls (¢ page 47).
SMS
Assign menu for SMS functions to a key
(¢ page 31).
SMS Notific.
Assign menu for activating SMS notification to a key (¢ page 34).
Withhold No.
Suppress Calling Line Identification for
the next call (¢ page 24).
If a function or number has already been
assigned to the left display key, the
selected function (or its abbreviation) will
be displayed in the lowest display line
above the display key.

Changing the display language
You can view the display texts in different
languages.
v ¢ Ð ¢ Handset ¢ Language
The current language is indicated by ‰ .
s
Select a language and
press §OK§.
a
If you accidentally choose a language you
do not understand:
v 5 4

Press keys in sequence.
s
Select the correct language
and press §OK§.

Setting the display
You have a choice of four colour schemes
and several different contrasts.
v ¢ Ð ¢ Display
Colour Scheme
s
Select a colour scheme and
press §OK§ ( ‰ = current colour).
a
Press briefly.
Contrast
r
Select contrast.
§Save§
a

Starting a function

Version 4, 16.09.2005

With the handset in idle status, press the
display key briefly.
The function menu is opened.

51


Handset settings

Setting the screen picture
You can display a screen picture (picture or
digital clock) when the handset is in idle
status. This will replace the idle status display. It may conceal the date, time and
name.
The screen picture is not displayed in certain situations, e.g. during a call or when
the handset has been de-registered.
If a screen picture has been activated,
the menu item Screen Picture is marked
with ‰ .
v ¢ Ð ¢ Display ¢ Screen Picture
The current setting is displayed.
Activation
Select On (screen picture is displayed)
or Off (no screen picture).
Selection:
Change screen picture if necessary (see
below).
If the screen picture conceals the display,
briefly press a to show the idle display
with time and date.

Changing the screen picture

v ¢ Ð ¢ Display ¢ Screen Picture
s
Scroll to the Selection line.
§View§
active screen picture is displayed.
s
Select screen picture and
press §Save§.

Version 4, 16.09.2005

Setting the display lighting
Depending on whether or not the handset
is in the charging cradle, you can activate
or deactivate the lighting. If it is activated,
the display is permanently dimmed.
v ¢ Ð ¢ Display ¢ Backlight
52

The current setting is displayed.
In Charger
Select On or Off.
Without Charger
Select On or Off.

Please note
With the On setting, the standby time
of the handset can be significantly
reduced.
§Save§

a


Activating/deactivating auto
answer
If you activate this function, when you
receive a call you can simply lift the handset out of the charging cradle without having to press the talk key c.
v ¢ Ð ¢ Handset
Auto Answer
a

Changing the speaker/earpiece
volume
You can set the loudspeaker volume for
speaker mode to five different levels and
the earpiece volume to three different levels.
t ¢ Handset Volume
r
Set the earpiece volume.
s
Scroll to the Speaker line.
r
Set the speaker volume.
§Save§
Press display key if necessary
to save the setting permanently.


Handset settings
Setting the volume during a call:
t
Press the control key.
r
Select volume.
§Save§
Press display key if necessary
to save the setting permanently.
The setting will automatically be saved
after approx. 3 seconds, if not then press
the display key §Save§.
If t is assigned to another function,
e.g. call swap (¢ page 25):
§Options§
Open menu.
Volume
Configure setting (see above).

Please note
You can also make these settings via
the menu (¢ page 21).

Changing ringers
u Volume:

You can choose between five volumes
(1–5; e.g. volume 2 = ˆ) and
the "crescendo" ring (6; volume
increases with each ring =
‰).
u Ringers:
You can select various ringers.
You can set different ringers for the following functions:
u Ext. Calls: for external calls
u Internal Calls: for internal calls
u All: the same ringer for all functions

Version 4, 16.09.2005

Settings for individual functions
Set the volume and melody depending on
the type of signalling required.
t ¢ Ringer Settings
q
Select setting, e.g. Ext. Calls
and press §OK§.
r
Set volume (1–6).
s
Scroll to the next line.

r

Select melody.
Press the display key to save
the setting.

§Save§

Same ringer for all functions

t ¢ Ringer Settings ¢ All
¤ Set volume and ringer (see "Settings for
individual functions").
§Save§
Press the display key and confirm the security prompt with
§Yes§ to save the setting.
a

Please note

Activating/deactivating the ringer
You can deactivate the ringer on your
handset before you answer a call or when
the handset is in idle status; the ringer can
be deactivated permanently or just for the
current call. The ringer cannot be re-activated while an external call is in progress.

Deactivating the ringer permanently
*
Press and hold the star key.
The Ú icon appears in the display.

Reactivating the ringer
*

Press and hold the star key.

Deactivating the ringer for the current call
§Silence§


Activating/deactivating the alert tone
In place of the ringer you can activate an
alert tone. When you get a call, you will
hear a short tone ("Beep") instead of the
ringer.
*
Press and hold the star key
and within 3 seconds:
§Beep§§
Press the display key. A call will
now be signalled by one short
alert tone. º appears in the
display.
53


Base station settings

Silent alarm
Incoming calls and other messages are
indicated by a silent alarm.
In idle status:
t ¢ Silent Alert
Press §OK§ to activate or deactivate
( ‰ = on).

Please note

Version 4, 16.09.2005

Activating/deactivating advisory
tones
Your handset uses advisory tones to tell
you about different activities and statuses.
The following advisory tones can be activated/deactivated independently of each
other:
u Key tones: every key press is confirmed.
u Acknowledge tones:
– Confirmation tone (ascending tone
sequence): at the end of an entry/
setting and when an SMS or a new
entry arrives in the answering
machine list or calls list
– Error tone (descending tone
sequence): when you make an
incorrect entry
– Menu end tone: when scrolling to
the end of a menu
u Battery tone: the batteries need to be
charged.
t ¢ Advisory Tones
Key Tones
Select On or Off.
Confirm.
Select On or Off.
Battery

54

Select On, Off or In Call. The battery
warning tone is only activated/deactivated and only sounds during a call.
You cannot deactivate the confirmation
tone for placing the handset in the charging cradle.

Please note

Restoring the handset default
settings
You can reset individual settings and
changes that you have made. This will not
affect entries in the directory, call-by-call
list, calls list, SMS lists or the handset's
registration to the base station.
v ¢ Ð ¢ Handset ¢ Reset Handset
§Yes§
a

The base station settings are carried out
using a registered Gigaset E49H handset.

Protecting against unauthorised
access
Protect the system settings of the base station with a PIN known only to yourself.
The system PIN must be entered when, for
example, registering/deregistering a
handset to/from the base station or when
restoring the default settings.



Changing the system PIN
You can change the 4-digit system PIN set
on the base station (default setting: 0000)
to a 4-digit PIN known only by you.
Gigaset E495: Setting a system PIN facilitates remote operation of the answering
machine (page 43).
v ¢ Ð ¢ Base ¢ System PIN
~
Enter the current system PIN
and press §OK§.
~
Enter new system PIN. For
security reasons, the PIN is
shown as four stars (****).
s~
Jump to the next line, re-enter
new system PIN and press §OK§.
a

Resetting the system PIN
If you have forgotten your system PIN you
can reset the base station to the original
code 0000:
Disconnect the power cord from the base
station. Hold down the registration/paging key on the base station while reconnecting the power cable to the base station. Release the key after a while.
The base station has now been reset and
the system PIN 0000 set.

Please note
All handsets are deregistered and must
be re-registered.

Activating/deactivating music
on hold

Version 4, 16.09.2005

v ¢ Ð ¢ Base ¢ Music on hold
Press §OK§ to activate or deactivate music
on hold ( ‰ = on).

Repeater support
With a repeater you can increase the range
and reception strength of your base station. You will need to activate repeater
mode. This will terminate any calls that
are in progress at the time.
Precondition: A repeater is registered.
The Eco Mode / Eco Mode+ is deactivated.
¢ Repeater Mode
§Yes§
When repeater mode is active, the menu
item is marked with ‰ .

Please note
Repeater support and Eco Mode/Eco
Mode+ (¢ page 45) cancel each
other out, i.e. both functions cannot be
used at the same time.

Restoring the base station to the
factory settings
When the settings are restored:
u handsets are still registered
u the system PIN is not reset
v ¢ Ð ¢ Base ¢ Base Reset
~
Enter the system PIN and
press §OK§.
§Yes§
Cancel the restoring process by pressing
a or the display key §No§.
a
Press and hold (idle status)

55

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / pabx.fm / 19.02.2009

Connecting the base station to the PABX

Connecting the base station
to the PABX
The following settings are only necessary
when your PABX requires them; see the
PABX user guide.
You cannot send or receive SMS messages
on PABXs that do not support Calling Line
Identification.

Dialling modes and recall
The current setting is indicated by ‰ .

Changing the dialling mode
The following dialling modes can be
selected:
u Tone dialling (DTMF)
u Dial pulsing (DP)
¢ Dialling Mode
s
Select dialling mode ( ‰ = on)
and press §OK§.
a

Setting recall

Version 4, 16.09.2005

Your phone is preset at the factory for
operation on the main connection. For
operation on a PABX, you may have to
change this value. Please refer to the user
guide for your PABX.
¢ Recall
s
Select recall and press §OK§
( ‰ = set value). Possible values are:
80 ms, 100 ms, 120 ms,
180 ms, 250 ms, 300 ms,
600 ms, 800 ms.
a

56

Saving an access code
(outside line code)
Precondition: You may have to enter an
access code for external calls in your PABX,
e.g. "0".
¢ Access Code
~
Enter or change access code,
max. 3 digits.
If an access code has been saved:
u The access code is prefixed automatically when you select from the following lists: numbers of the SMS centres,
calls list or answering machine list.
u The access code must be entered when
dialling manually and when manually
entering directory, emergency/shortcut
numbers and SMS centre numbers.
u If you copy the recipient's number from
the directory when sending an SMS,
you have to delete the access code.
u An existing access code is deleted
using X.

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / pabx.fm / 19.02.2009

Connecting the base station to the PABX

Setting pauses
Changing pause after line seizure
You can change the length of pause that is
inserted between pressing the talk key
c and sending the number.
v
Open menu.
55O
L
Press keys.
~
Enter digit for the pause
length (1 = 1 sec.; 2 = 3 sec.;
3 = 7 sec.) and press §OK§.

Switching temporarily to tone
dialling (DTMF)
If your PABX still operates with dial pulsing
(DP), but you need tone dialling for a
connection (e.g. to listen to the network
mailbox) you must switch to tone dialling
for the call.
Precondition: You are conducting a call or
have already dialled an external number.
*
Press the star key.
After the call is ended, dial pulsing is automatically activated again.

Changing the pause after the recall key
You can change the length of the pause if
your PABX requires this (refer to the user
guide for your PABX).
v
Open menu.
55O
2
Press keys.
~
Enter a digit for the length of
the pause (1 = 800 ms;
2 = 1600 ms; 3 = 3200 ms)
and press §OK§.

Changing a dialling pause (pause after
access code)

Version 4, 16.09.2005

Precondition: You have saved an access
code (¢ page 56).
v
Open menu.
55O

Press keys.
~
Enter a digit for the length of
the pause (1 = 1 sec.;
2 = 2 sec.; 3 = 3 sec.;
4 = 6 sec.) and press §OK§.
To insert a dialling pause: press S for
2 seconds. A P appears in the display.

57

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / appendix.fm / 19.02.2009

Service (Customer Care)

The display is blank.

We offer you support that is fast and tailored to your specific needs!
Our Online Support on the Internet can be
reached any time from anywhere.
www.gigaset.com/customercare
It provides you with 24/7 support for all
our products. It also provides a list of FAQs
and answers plus user guides and current
software updates (if available for the product) for you to download.
You will also find frequently asked questions and answers in the appendix of this
user guide.
For personal advice on our range of products and assistance with repairs or guarantee/warranty claims you can contact us
on:
UK helpdesk: 0 84 53 67 08 12.
Please have your proof of purchase ready
when calling with regard to guarantee/
warranty claims.
Replacement or repair services are not
offered in countries where our product is
not sold by authorised dealers.

1. The handset is not switched on.
Press and hold the end call key a.

¥

2. The batteries are flat.
Charge or replace the batteries
page 10).
(

¥

¢

"Base x" flashes on the display.
1. The handset is outside the range of the base
station.
Move the handset closer to the base station.

¥

The base station's range is reduced because
eco mode is activated.
Deactivate eco mode (
page 45) or
reduce the distance between the handset and the base station.

¥

¢

2. The base station is not turned on.
Check the base station's mains adapter
page 8).
(

¥

¢

"Please register" flashes in the display.
Handset has not been registered with the base
station or has been deregistered.
Register the handset (
page 46).

¥

¢

Handset does not ring.
1. The ringer is deactivated.
Activate the ringer (
page 53).

¥

¢

Questions and answers

2. Call divert set to All Calls.
Deactivate call divert (

If you have any questions about the use
of your phone, you can contact us 24/7
at www.gigaset.com/customercare.
The table below contains a list of common
problems and possible solutions.

You cannot hear a ringer/dialling tone from
the fixed line network.

¥

¢ page 25).

The phone cord supplied has not been used or
has been replaced by a new cord with the
wrong pin connections.
Please always use the phone cord supplied
or ensure that the pin connections are correct when purchasing from a retailer
page 8).
(

¥

¢

Error tone sounds after system PIN prompt
You have entered the wrong system PIN.
Reset the system PIN to 0000 (
page 55).

¥

¢

Version 4, 16.09.2005

Forgotten the system PIN.

¥

58

Reset the system PIN to 0000 (

¢ page 55).


Call charges are not displayed.
1. Your network provider does not support this
feature.
2. There are no metering pulses.
Ask your network provider to transmit
the metering pulses.

¥

The other party cannot hear you.
You have pressed the u (INT) key. The handset is "muted".
Activate the microphone again
page 23).
(

¥

¢

The number of the caller is not displayed
despite CLIP.
Calling Line Identification is not enabled.
The caller should ask the network provider
to enable Calling Line Identification (CLI).

¥

Authorisation
This device is intended for analogue
phone lines in the UK.
Country-specific requirements have been
taken into consideration.
We, Gigaset Communications GmbH,
declare that this device meets the
essential requirements and other relevant
regulations laid down in Directive 1999/5/
EC.
A copy of the 1999/5/EC Declaration of
Conformity is available at this Internet
address:
www.gigaset.com/docs.

You hear an error tone when keying an input
(a descending tone sequence).

¥

Action has failed/invalid input.
Repeat the operation.
Watch the display and refer to the user
guide if necessary.

Guarantee Certificate
United Kingdom

You cannot listen to messages on the network mailbox.

Without prejudice to any claim the user
(customer) may have in relation to the
dealer or retailer, the customer shall be
granted a manufacturer's Guarantee
under the conditions set out below:
u In the case of new devices and their
components exhibiting defects resulting from manufacturing and/or material faults within 24 months of purchase, Gigaset Communications shall,
at its own option and free of charge,
either replace the device with another
device reflecting the current state of
the art, or repair the said device. In
respect of parts subject to wear and
tear (including but not limited to, batteries, keypads, casing), this warranty
shall be valid for six months from the
date of purchase.
u This Guarantee shall be invalid if the
device defect is attributable to
improper treatment and/or failure to
comply with information contained in
the user guides.

Your PABX is set for dial pulsing.
Set your PABX to tone dialling.

¥

E495 Gigaset only:
No time is specified for a message in the
calls list.
Date and time have not been set.
Set the date/time (
page 13).

¥

¢

The answering machine announces "PIN is
incorrect" during remote operation.
1. You have entered the wrong system PIN.
Enter the system PIN again.

¥

2. The system PIN is still set to 0000.
Change the system PIN (
page 55).

¥

¢

Version 4, 16.09.2005

The answering machine is not recording any
messages/has switched over to announce
only.
Its memory is full.
Delete old messages.
Play back new messages and delete.

¥
¥

59


Environment

Version 4, 16.09.2005

u This Guarantee shall not apply to or

extend to services performed by the
authorised dealer or the customer
themselves (e. g. installation, configuration, software downloads). User
guides and any software supplied on a
separate data medium shall be
excluded from the Guarantee.
u The purchase receipt, together with the
date of purchase, shall be required as
evidence for invoking the Guarantee.
Claims under the Guarantee must be
submitted within two months of the
Guarantee default becoming evident.
u Ownership of devices or components
replaced by and returned to Gigaset
Communications shall vest in Gigaset
Communications.
u This Guarantee shall apply to new
devices purchased in the European
Union. For Products sold in the United
Kingdom the Guarantee is issued by:
Gigaset Communications GmbH, Schlavenhorst 66, D-46395 Bocholt, Germany.
u Any other claims resulting out of or in
connection with the device shall be
excluded from this Guarantee. Nothing
in this Guarantee shall attempt to limit
or exclude a Customers Statutory
Rights, nor the manufacturer's liability
for death or personal injury resulting
from its negligence.
u The duration of the Guarantee shall not
be extended by services rendered
under the terms of the Guarantee.
u Insofar as no Guarantee default exists,
Gigaset Communications reserves the
right to charge the customer for
replacement or repair.
u The above provisions does not imply a
change in the burden of proof to the
detriment of the customer.
To invoke this Guarantee, please contact
the Gigaset Communications telephone
service. The relevant number is to be
found in the accompanying user guide.
60

Environment
Our environmental mission statement
Gigaset Communications GmbH assumes
social responsibility and is actively committed to a better world. Our ideas, technologies and actions serve people, society
and the environment. The aim of our global activity is to secure sustainable life
resources for humanity. We are committed
to a responsibility for our products that
comprises their entire life cycle. The environmental impact of products, including
their manufacture, procurement, distribution, use, service and disposal, are already
evaluated during product and process
design.
Further information on environmentally
friendly products and processes is available on the Internet at www.gigaset.com.

Environmental management system
Gigaset Communications
GmbH is certified pursuant to the international
standards EN 14001 and
ISO 9001.
ISO 14001 (Environment): certified since
September 2007 by TüV SÜD Management Service GmbH.
ISO 9001 (Quality): certified since 17/02/
1994 by TüV Süd Management Service
GmbH.

Ecological energy consumption

The use of ECO DECT (¢ page 45) saves
energy and makes an active contribution
towards protecting the environment.


Appendix

Disposal

Version 4, 16.09.2005

Batteries should not be disposed of in general household waste. Observe the local
waste disposal regulations, details of
which can be obtained from your local
authority or the dealer you purchased the
product from.
All electrical and electronic equipment
must be disposed of separately from general household waste using the sites designated by local authorities.
If a product displays this
symbol of a crossed-out
rubbish bin, the product is
subject to European Directive 2002/96/EC.
The appropriate disposal
and separate collection of
used equipment serve to prevent potential
harm to the environment and to health.
They are a precondition for the re-use and
recycling of used electrical and electronic
equipment.
For further information on disposing of
your used equipment, please contact your
local authority, your refuse collection service or the dealer you purchased the product from.

Appendix
Care

¤ Wipe the base station, charging cradle

and the handset with a damp cloth (do
not use solvent) or an antistatic cloth.
Never use a dry cloth as this can cause
static discharge.

Contact with liquid

!

If the handset should come into contact
with liquid:
1. Switch the handset off and remove
the batteries immediately.
2. Allow the liquid to drain from the handset.
3. Pat all parts dry, then place the handset
with the battery compartment open
and the keypad facing down in a dry,
warm place for at least 72 hours (not
in a microwave, oven etc.).
4. Do not switch on the handset again
until it is completely dry.
When it has fully dried out, you will normally be able to use it again.
In rare cases, contact with chemical substances can cause changes to the telephone's exterior. Due to the wide variety
of chemical products available on the market, it was not possible to test all substances.

61


Appendix

Specifications

Base station power consumption

Recommended batteries
Technology:
Nickel-metal-hydride (NiMH)
Size:
AAA (Micro, HR03)
Voltage: 1,2 V
Capacity: 600 - 1200 mAh
We recommend the following battery
types, because these are the only ones
that guarantee the specified operating
times, full functionality and long service
life:
u GP 700 mAh
u Yuasa Phone 700 mAh
u Yuasa AAA 800 mAh
u Peacebay 650 mAh
The device is supplied with two recommended batteries.

In standby mode:
Gigaset E490: approx. 0,8 watt
During the conversation:

General specifications
DECT standard

is supported

GAP standard

is supported

No. of channels

60 duplex channels

Radio frequency
range

1880–1900 MHz

The operating time of your Gigaset
depends on the capacity and age of the
batteries and the way they are used. (All
times are maximum possible times and
apply when the display lighting is
switched off).

Time multiplex,
10 ms frame length

Channel grid

1728 kHz

Bit rate

1152 kbit/s

Modulation

GFSK

Language code

Handset operating times/charging
times

Duplex method

32 kbit/s

Transmission
power

10 mW, average power per
channel

Range

up to 300 m outdoors,
up to 50 m indoors

Base station
power supply

230 V ~/50 Hz

Capacity (mAh) approx.

Environmental
+5°C to +45°C;
conditions in oper- 20% to 75% relative
ation
humidity

500 700 900 1100

Dialling mode

Standby time (hours) 180 250 320

395

9

12

16

19

Operating time for
1.5 hrs of calls per
day (hours)

80

115 150

180

Charging time
(hours)

Version 4, 16.09.2005

Talktime (hours)

5

7

9

11

Due to the constant progression in battery
development, the list of recommended
batteries in the FAQ section of the Gigaset
Customer Care pages is regularly updated:
www.gigaset.com/customercare
62

DTMF ( tone dialling)/
DP (dial pulsing)

Pin connections on the telephone jack
3
2
1

4
5
6

1
2
3
4
5
6

unused
unused
a
b
unused
unused


Appendix

Writing and editing text

Setting upper/lower case or digits

The following rules apply when writing
text:
u Control the cursor with u v t s.
u Characters are inserted at the cursor
position.
u Press the star key * to show the table
of special characters. Select the
required character, press the display
key §Insert§ to insert the character at the
cursor position.
u The first letter of the name of directory
entries is automatically capitalised, followed by lower case letters.

Press the hash key # briefly to switch
from "Abc" mode to "123" and from "123"
to "abc" and from "abc" to "Abc" (upper
case: 1st letter upper case, all others lower
case). Press the hash key # before
entering the letter.
You can see briefly in the display whether
upper case, lower case or digits is
selected.

Writing an SMS/names
Press the relevant key several times to
enter letters/characters.

Standard characters
1x

2
3
4
5
L
M
N
O
Q

2x

a
d
g
j
m
p
t
w
.

3x
2)

1)

b
e
h
k
n
q
u
x
,

4x

5x

6x

7x

8x

9x 10x

1
c
f
i
l
o
r
v
y
?

2
3
4
5
6
s
8
z
!

ä
ë
ï

á
é
í

à
è
ì

â
ê
î

ã

ç

ö
7
ü
9
0

ñ
ß
ú
ÿ

ó

ò

ô

õ

ù
ý

û
æ

ø

å

1) Space
2) Line break

Version 4, 16.09.2005

When you press and hold a key, the characters of that key appear in the display and
are highlighted one after the other. When
you release the key, the highlighted character is inserted into the input field.

63

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / accessories_SAG.fm / 19.02.2009

Accessories

Accessories
Gigaset handsets
Upgrade your Gigaset to a cordless PABX:

Gigaset E49H handset
u
u
u
u
u
u
u
u
u
u

Dust and splashproof casing
Illuminated graphic colour display (65k colours)
Illuminated keypad
Speaker
Silent alarm
Polyphonic ringers
Directory for around 150 entries
SMS (precondition: CLIP must be enabled)
Headset socket
Room monitor
www.gigaset.com/gigasete49h

Gigaset SL78H handset
u
u
u
u
u
u
u
u
u

Version 4, 16.09.2005

Illuminated keypad
Speaker
Polyphonic ringers
PC interface to manage directory entries
Bluetooth
Room monitor
www.gigaset.com/gigasetsl78h

64


Accessories

Gigaset C47H handset
u
u
u
u
u
u
u
u

Illuminated keypad
Speaker
Polyphonic ringers
Headset socket
Room monitor
www.gigaset.com/gigasetc47h

Gigaset S68H handset
u
u
u
u
u
u
u
u
u

Illuminated keypad
Speaker
Polyphonic ringers
Picture CLIP
Headset socket
Room monitor
www.gigaset.com/gigasets68h

Gigaset SL37H handset

Version 4, 16.09.2005

u
u
u
u
u
u
u
u

Illuminated keypad
Speaker
Polyphonic ringers
Picture CLIP
PC interface e.g. for managing directory entries,
ringers and screensavers
u Headset socket
u Bluetooth
u Room monitor
u Walky-talky function
www.gigaset.com/gigasetsl37h
65


Mounting the base station to the wall

Mounting the base station to the wall
99 mm

approx. 2.5 mm

Mounting the charging cradle to the wall
21 mm

Version 4, 16.09.2005

approx. 2.5 mm

66

Gigaset E490/E495 / GBR / A31008-M2105-L101-1-7619 / E495SIX.fm / 19.02.2009

Index

Index

Version 4, 16.09.2005

A
Access code . . . . . . . . . . . . . . . . . . . . 56
for a PABX . . . . . . . . . . . . . . . . . . . 56
Access protection . . . . . . . . . . . . . . . . 54
Accessories . . . . . . . . . . . . . . . . . . . . 64
Acknowledge tones . . . . . . . . . . . . . . 54
Activating
advisory tones . . . . . . . . . . . . . . . . 54
answering machine . . . . . . . . . . . . 38
answering machine
(remote operation) . . . . . . . . . . 43
handset . . . . . . . . . . . . . . . . . . . . . 18
keypad lock . . . . . . . . . . . . . . . . . . 18
listening in . . . . . . . . . . . . . . . . . . . 48
muting ringer . . . . . . . . . . . . . . . . . 36
ring delay . . . . . . . . . . . . . . . . . . . . 52
room monitor . . . . . . . . . . . . . . . . . 50
two-way record . . . . . . . . . . . . . . . 41
Advisory tones . . . . . . . . . . . . . . . . . . 54
Alarm clock . . . . . . . . . . . . . . . . . . . . 46
Alert tone . . . . . . . . . . . . . . . . . . . . . 53
Announcement
(answering machine) . . . . . . . . . . 39
Announcement mode
(answering machine) . . . . . . . 38, 39
Anonymous calling . . . . . . . . . . . . . . 24
Answering machine . . . . . . . . . . . . . . 38
activating/deactivating . . . . . . . . . . 38
deleting messages . . . . . . . . . . . . . 40
list . . . . . . . . . . . . . . . . . . . . . . 28, 29
playing back messages . . . . . . . . . . 40
recording announcement/announce
only . . . . . . . . . . . . . . . . . . . . . 38
remote operation . . . . . . . . . . . . . . 43
scrolling back . . . . . . . . . . . . . . . . . 40
scrolling forward. . . . . . . . . . . . . . . 40
Answering machine, see also
Network mailbox
Assigning numerical keys . . . . . . . . . . 51
Authorisation . . . . . . . . . . . . . . . . . . . 59
Automatic
call acceptance . . . . . . . . . . . . . 22, 52
network provider preselection . . . . . 30
ring delay . . . . . . . . . . . . . . . . . . . . 52

B
Base station
connecting . . . . . . . . . . . . . . . . . . . 8
connecting to PABX . . . . . . . . . . . . 56
restoring factory settings . . . . . . . . 55
setting . . . . . . . . . . . . . . . . . . . . . 54
setting up . . . . . . . . . . . . . . . . . . . . 8
system PIN . . . . . . . . . . . . . . . . . . 55
Battery
charging . . . . . . . . . . . . . . . . . . 1, 12
display . . . . . . . . . . . . . . . . . . . . . . 1
icon . . . . . . . . . . . . . . . . . . . . . . . . 1
inserting . . . . . . . . . . . . . . . . . . . . 10
recommended batteries . . . . . . . . . 62
tone . . . . . . . . . . . . . . . . . . . . . . . 54

C
Call
accepting . . . . . . . . . . . . . . . . . . . 22
diverting (connecting) . . . . . . . . . . 47
ending . . . . . . . . . . . . . . . . . . . . . 22
external . . . . . . . . . . . . . . . . . . . . . 22
internal . . . . . . . . . . . . . . . . . . . . . 47
make anonymous call . . . . . . . . . . 24
participant listening in . . . . . . . . . . 48
picking up from ans. machine . . . . . 41
transferring (connecting) . . . . . . . . 49
two-way record . . . . . . . . . . . . . . . 41
Call divert . . . . . . . . . . . . . . . . . . . . . 25
Call duration . . . . . . . . . . . . . . . . . . . 22
Call screening during recording . . . . . 41
Call swap . . . . . . . . . . . . . . . . . . . . . 25
Call waiting
accepting/rejecting . . . . . . . . . . . . 24
external call . . . . . . . . . . . . . . . . . . 24
internal call . . . . . . . . . . . . . . . . . . 48
Call-by-call
key . . . . . . . . . . . . . . . . . . . . . . . . . 1
list . . . . . . . . . . . . . . . . . . . . . . . . 26
numbers . . . . . . . . . . . . . . . . . 26, 30
Calling
anonymously . . . . . . . . . . . . . . . . . 24
external . . . . . . . . . . . . . . . . . . . . . 22
internal . . . . . . . . . . . . . . . . . . . . . 47
Calling Line Identification . . . . . . . . . 22
cancel once . . . . . . . . . . . . . . . . . . 24
Calls list . . . . . . . . . . . . . . . . . . . . . . 29

67


Index
Cancelling preselection . . . . . . . . . . . 30
Care of the telephone . . . . . . . . . . . . 61
CD, see Call divert
Changing
destination number . . . . . . . . . . . . 50
dialling mode . . . . . . . . . . . . . . . . . 56
display language . . . . . . . . . . . . . . . 51
earpiece volume . . . . . . . . . . . . . . . 52
internal number of a handset . . . . . 49
name of a handset . . . . . . . . . . . . . 49
pause time . . . . . . . . . . . . . . . . . . . 57
ringer . . . . . . . . . . . . . . . . . . . . . . . 53
speaker volume . . . . . . . . . . . . . . . 52
system PIN . . . . . . . . . . . . . . . . . . . 55
Character set . . . . . . . . . . . . . . . . 32, 33
Charge status display . . . . . . . . . . . . . . 1
CLI, CLIP . . . . . . . . . . . . . . . . . . . . . . 22
CLIP picture . . . . . . . . . . . . . . . . . . . . 23
CLIR. . . . . . . . . . . . . . . . . . . . . . . . . . 24
Conference (internal) . . . . . . . . . . . . . 48
Confirmation tone . . . . . . . . . . . . . . . 54
Connecting the headset . . . . . . . . . . . 14
Connecting, base station to PABX . . . . 56
Consultation call (internal) . . . . . . . . . 48
Control key . . . . . . . . . . . . . . . . . . 1, 16
Correcting incorrect entries . . . . . . . . 17
Cost saving function
(remote operation) . . . . . . . . . . . 42
Customer Care . . . . . . . . . . . . . . . . . . 58

Version 4, 16.09.2005

D
Deactivating
advisory tones . . . . . . . . . . . . . . . . 54
handset . . . . . . . . . . . . . . . . . . . . . 18
keypad lock . . . . . . . . . . . . . . . . . . 18
listening in . . . . . . . . . . . . . . . . . . . 48
muting ringer . . . . . . . . . . . . . . . . . 36
ring delay . . . . . . . . . . . . . . . . . . . . 52
room monitor . . . . . . . . . . . . . . . . . 50
two-way record . . . . . . . . . . . . . . . 41
Delete key . . . . . . . . . . . . . . . . . . . . . 17
Deleting
announcement for answering
machine . . . . . . . . . . . . . . . . . 39
characters . . . . . . . . . . . . . . . . . . . 17
message . . . . . . . . . . . . . . . . . . . . . 40
Deregistering (handset) . . . . . . . . . . . 47
Destination number (room monitor) . . 50
Dial pulsing . . . . . . . . . . . . . . . . . . . . 56
68

Dialling
call-by-call list . . . . . . . . . . . . . . . . 27
directory . . . . . . . . . . . . . . . . . . . . 27
mode . . . . . . . . . . . . . . . . . . . . . . 56
using shortcut . . . . . . . . . . . . . . . . 27
Dialling pause . . . . . . . . . . . . . . . . . . 57
entering . . . . . . . . . . . . . . . . . . . . . 1
Directory . . . . . . . . . . . . . . . . . . . . . 26
copying number from text . . . . . . . 28
managing entries. . . . . . . . . . . . . . 27
opening . . . . . . . . . . . . . . . . . . . . 16
order of entries . . . . . . . . . . . . . . . 26
saving entry . . . . . . . . . . . . . . . . . 26
saving the sender’s number (SMS) . 33
sending entry/list to handset . . . . . 27
using to enter numbers . . . . . . . . . 28
Display
changing display language . . . . . . . 51
contrast. . . . . . . . . . . . . . . . . . . . . 51
in idle status . . . . . . . . . . . . . . . . . 18
lighting . . . . . . . . . . . . . . . . . . . . . 52
memory (directory/call-by-call) . . . . 27
network mailbox message . . . . . . . 44
number (CLI/CLIP) . . . . . . . . . . . . . 22
screen picture . . . . . . . . . . . . . . . . 52
setting . . . . . . . . . . . . . . . . . . . . . 51
wrong language . . . . . . . . . . . . . . 51
Display keys . . . . . . . . . . . . . . . . . 1, 17
assigning . . . . . . . . . . . . . . . . . . . . 51
Disposal . . . . . . . . . . . . . . . . . . . . . . 61
DP (dial pulsing) . . . . . . . . . . . . . . . . 56
Draft message list (SMS) . . . . . . . . . . 31

E
Earpiece mode . . . . . . . . . . . . . . . . . 23
Earpiece volume . . . . . . . . . . . . . . . . 52
ECO DECT . . . . . . . . . . . . . . . . . . . . . 45
Eco mode . . . . . . . . . . . . . . . . . . . . . 45
Eco mode+ . . . . . . . . . . . . . . . . . . . . 45
End call key. . . . . . . . . . . . . . . . . . 1, 22
Ending, call . . . . . . . . . . . . . . . . . . . . 22
Ending, see Deactivate
Entry
saving, changing (preselection) . . . 30
select from directory . . . . . . . . . . . 26
Environment . . . . . . . . . . . . . . . . . . . 60
Error tone . . . . . . . . . . . . . . . . . . . . . 54
External call . . . . . . . . . . . . . . . . . . . 25
call waiting . . . . . . . . . . . . . . . . . . 24
divert to ans. mach. . . . . . . . . . . . . 41


Index

F
Fast access
network mailbox . . . . . . . . . . . . . . . 44

G
Group call . . . . . . . . . . . . . . . . . . . . . 47
Guarantee Certificate . . . . . . . . . . . . . 59

H
Handset
advisory tones . . . . . . . . . . . . . . . . 54
changing internal number . . . . . . . . 49
changing name . . . . . . . . . . . . . . . 49
changing the number . . . . . . . . . . . 49
contact with liquid . . . . . . . . . . . . . 61
de-registering . . . . . . . . . . . . . . 46, 47
display language . . . . . . . . . . . . . . . 51
display lighting . . . . . . . . . . . . . . . . 52
diverting a call . . . . . . . . . . . . . . . . 47
earpiece volume . . . . . . . . . . . . . . . 52
idle status . . . . . . . . . . . . . . . . . . . 18
list . . . . . . . . . . . . . . . . . . . . . . . . . 16
locating . . . . . . . . . . . . . . . . . . . . . 47
muting . . . . . . . . . . . . . . . . . . . . . . 23
paging . . . . . . . . . . . . . . . . . . . . . . 47
registering . . . . . . . . . . . . . . . . . . . 46
restoring to factory settings. . . . . . . 54
screen picture . . . . . . . . . . . . . . . . . 52
setting . . . . . . . . . . . . . . . . . . . . . . 51
setting up . . . . . . . . . . . . . . . . . . . . 10
speaker volume . . . . . . . . . . . . . . . 52
using room monitor . . . . . . . . . . . . 49
using several . . . . . . . . . . . . . . . . . 46
Handset operating time
in room monitor mode . . . . . . . . . . 50
Hash key . . . . . . . . . . . . . . . . . . . . 1, 18
Headset socket. . . . . . . . . . . . . . . . . . 14
Hearing aids . . . . . . . . . . . . . . . . . . . . 6

Version 4, 16.09.2005

I
Icon
alarm clock . . . . . . . . . . . . . . . . . . . 46
for new messages . . . . . . . . . . . . . . 28
keypad lock . . . . . . . . . . . . . . . . . . 18
new message . . . . . . . . . . . . . . . . . 40
new SMS . . . . . . . . . . . . . . . . . . . . 32
ringer . . . . . . . . . . . . . . . . . . . . . . . 53

Idle status (display) . . . . . . . . . . . . . . 18
Idle status, returning to . . . . . . . . . . . 18
Incoming message list (SMS) . . . . . . . 32
Incorrect input (correction) . . . . . . . . 17
Installing, base station . . . . . . . . . . . . 8
Internal
conference . . . . . . . . . . . . . . . . . . 48
consulting . . . . . . . . . . . . . . . . . . . 48
listening in . . . . . . . . . . . . . . . . . . 48
making calls . . . . . . . . . . . . . . . . . 47
Internal call. . . . . . . . . . . . . . . . . . . . 47
call waiting . . . . . . . . . . . . . . . . . . 48

K
Key 1 (fast access) . . . . . . . . . . . . . 1, 42
Keypad lock . . . . . . . . . . . . . . . . . . . 18
Keys
assigning directory entry . . . . . . . . 26
call-by-call list . . . . . . . . . . . . . . . . . 1
control key . . . . . . . . . . . . . . . . 1, 16
delete key . . . . . . . . . . . . . . . . . . . 17
display keys . . . . . . . . . . . . . . . . 1, 17
end call key . . . . . . . . . . . . . . . . 1, 22
fast access . . . . . . . . . . . . . . . . . 1, 42
hash key . . . . . . . . . . . . . . . . . . 1, 18
message key . . . . . . . . . . . . . . . . . . 1
on/off key . . . . . . . . . . . . . . . . . . . . 1
recall key . . . . . . . . . . . . . . . . . . . . . 1
shortcut . . . . . . . . . . . . . . . . . 26, 27
speaker key . . . . . . . . . . . . . . . . 1, 14
star key . . . . . . . . . . . . . . . . . . . . . . 1
talk key . . . . . . . . . . . . . . . . . . . 1, 22

L
Language, display . . . . . . . . . . . . . . . 51
Last number redial . . . . . . . . . . . . . . 28
Linking, see SMS
Liquid . . . . . . . . . . . . . . . . . . . . . . . . 61
List
answering machine . . . . . . . . . 28, 29
call-by-call list . . . . . . . . . . . . . . . . 26
calls list . . . . . . . . . . . . . . . . . . . . . 29
handsets . . . . . . . . . . . . . . . . . . . . 16
missed calls . . . . . . . . . . . . . . . . . . 29
network mailbox . . . . . . . . . . . . . . 29
SMS draft message list . . . . . . . . . . 31
SMS incoming message list . . . . . . 32
SMS list . . . . . . . . . . . . . . . . . . . . . 29
Listening in to a call . . . . . . . . . . . . . 48
Locating, handset . . . . . . . . . . . . . . . 47
69


Index
Lock
activating/deactivating keypad lock . 18

M
Mailbox ID, see SMS
Mailboxes, see SMS
Mains adapter . . . . . . . . . . . . . . . . . . . 6
Making calls
accepting a call . . . . . . . . . . . . . . . . 22
cost-effective calls . . . . . . . . . . . . . 30
external . . . . . . . . . . . . . . . . . . . . . 22
internal . . . . . . . . . . . . . . . . . . . . . 47
Manual last number redial . . . . . . . . . 28
Medical appliances . . . . . . . . . . . . . . . . 6
Memory
directory/call-by-call . . . . . . . . . . . . 27
Menu
end tone . . . . . . . . . . . . . . . . . . . . 54
opening . . . . . . . . . . . . . . . . . . . . . 16
overview . . . . . . . . . . . . . . . . . . . . 20
prompting . . . . . . . . . . . . . . . . . . . 17
Message key
open list . . . . . . . . . . . . . . . . . . . . . 32
opening lists . . . . . . . . . . . . . . . . . . 28
Messages . . . . . . . . . . . . . . . . . . . . . 38
deleting . . . . . . . . . . . . . . . . . . . . . 40
key . . . . . . . . . . . . . . . . . . . . . . . . . . 1
marking as "new" . . . . . . . . . . . . . . 40
new message icon . . . . . . . . . . . . . 40
playing back . . . . . . . . . . . . . . . . . . 40
Microphone . . . . . . . . . . . . . . . . . . . . . 1
Missed calls . . . . . . . . . . . . . . . . . . . . 29
Music on hold . . . . . . . . . . . . . . . 23, 55
setting . . . . . . . . . . . . . . . . . . . . . . 55
Muting
first ring . . . . . . . . . . . . . . . . . . . . . 36
handset . . . . . . . . . . . . . . . . . . . . . 23

N

Version 4, 16.09.2005

Name
of a handset . . . . . . . . . . . . . . . . . . 49
Network mailbox . . . . . . . . . . . . . . . . 44
Network provider (numbers list) . . . . . 26
Network provider preselection,
automatic . . . . . . . . . . . . . . . . . . 30

70

Network services. . . . . . . . . . . . . . . .
Notification by SMS . . . . . . . . . . . . . .
Number
as destination for room monitor . . .
copying from an SMS text . . . . . . .
copying from directory . . . . . . . . . .
copying to directory . . . . . . . . . . . .
displaying caller's number (CLIP) . . .
entering with directory. . . . . . . . . .
saving in the directory . . . . . . . . . .
Numbers list
network provider . . . . . . . . . . . . . .

24
34
50
33
28
28
22
28
26
26

O
On/Off key . . . . . . . . . . . . . . . . . . . . . 1
Order in directory . . . . . . . . . . . . . . . 26

P
PABX
connecting base station . . . . . . . . . 56
pauses . . . . . . . . . . . . . . . . . . . . . 57
saving access code . . . . . . . . . . . . . 56
setting dialling mode . . . . . . . . . . . 56
setting recall . . . . . . . . . . . . . . . . . 56
SMS . . . . . . . . . . . . . . . . . . . . . . . 36
switching to tone dialling . . . . . . . . 57
Pack contents . . . . . . . . . . . . . . . . . . . 7
Paging . . . . . . . . . . . . . . . . . . . . . . . 47
Paging key . . . . . . . . . . . . . . . . . . . . . 2
Pause . . . . . . . . . . . . . . . . . . . . . . . . 57
PIN change
system PIN . . . . . . . . . . . . . . . . . . 55
Pin connections . . . . . . . . . . . . . . . . 62
Playing back
announcement (answering
machine) . . . . . . . . . . . . . . . . 39
message (answering machine) . . . . 40
Power consumption . . . . . . . . . . . . . 62
Preselection . . . . . . . . . . . . . . . . . . . 30
cancelling . . . . . . . . . . . . . . . . . . . 30
Protecting the phone against
access . . . . . . . . . . . . . . . . . . . . 54

Q
Questions and answers . . . . . . . . . . . 58


Index

R
Recall . . . . . . . . . . . . . . . . . . . . . . . . 56
Recall key . . . . . . . . . . . . . . . . . . . . . . 1
pause after . . . . . . . . . . . . . . . . . . . 57
Reception booster, see Repeater
Recording
quality . . . . . . . . . . . . . . . . . . . . . . 42
time . . . . . . . . . . . . . . . . . . . . . . . . 42
two-way record . . . . . . . . . . . . . . . 41
Redirect, see Call divert
Registering (handset) . . . . . . . . . . . . . 46
Registration key . . . . . . . . . . . . . . . . . . 2
Remote operation . . . . . . . . . . . . . . . 43
Repeater . . . . . . . . . . . . . . . . . . . . . . 55
Ring delay . . . . . . . . . . . . . . . . . . 42, 52
Ringback . . . . . . . . . . . . . . . . . . . . . . 24
Ringer
changing . . . . . . . . . . . . . . . . . . . . 53
muting . . . . . . . . . . . . . . . . . . . . . . 36
setting volume . . . . . . . . . . . . . . . . 53
Room monitor . . . . . . . . . . . . . . . . . . 49

Version 4, 16.09.2005

S
Saving (access code) . . . . . . . . . . . . . 56
Screen picture . . . . . . . . . . . . . . . . . . 52
Searching in directory . . . . . . . . . . . . 26
Sending directory entry to handset . . . 27
Sensitivity (room monitor) . . . . . . . . . 50
Service . . . . . . . . . . . . . . . . . . . . . . . 58
Setting the date . . . . . . . . . . . . . . . . . 13
Setting the time . . . . . . . . . . . . . . . . . 13
Setting up
handset . . . . . . . . . . . . . . . . . . . . . 10
Shortcut . . . . . . . . . . . . . . . . . . . . . . 20
Signal tone, see Advisory tones
Silent alarm . . . . . . . . . . . . . . . . . . . . 54
SMS . . . . . . . . . . . . . . . . . . . . . . . . . 31
active send service centre . . . . . . . . 35
changing mailbox . . . . . . . . . . . . . . 35
deleting . . . . . . . . . . . . . . . . . . 32, 33
diverting . . . . . . . . . . . . . . . . . . . . 33
draft message list . . . . . . . . . . . . . . 31
incoming message list. . . . . . . . . . . 32
linked . . . . . . . . . . . . . . . . . . . . . . . 31
list . . . . . . . . . . . . . . . . . . . . . . . . . 29
mailbox ID . . . . . . . . . . . . . . . . . . . 34
mailboxes . . . . . . . . . . . . . . . . . . . . 34
notification by SMS . . . . . . . . . . . . . 34
notification number . . . . . . . . . . . . 34

notification type . . . . . . . . . . . . . . 34
PIN protection . . . . . . . . . . . . . . . . 34
reading . . . . . . . . . . . . . . . . . . 32, 33
receiving . . . . . . . . . . . . . . . . . . . . 32
replying to or diverting. . . . . . . . . . 33
saving number. . . . . . . . . . . . . . . . 33
self help with error messages . . . . . 37
sending to a personal mailbox . . . . 35
troubleshooting . . . . . . . . . . . . . . . 37
writing . . . . . . . . . . . . . . . . . . 31, 63
SMS centre
changing number . . . . . . . . . . . . . 35
setting . . . . . . . . . . . . . . . . . . . . . 35
SMS to PABXs . . . . . . . . . . . . . . . . . . 36
Snooze mode . . . . . . . . . . . . . . . . . . 46
Sound, see Ringer
Speaker . . . . . . . . . . . . . . . . . . . . . . 23
key . . . . . . . . . . . . . . . . . . . . . . 1, 14
Special functions . . . . . . . . . . . . . . . . 56
Specifications . . . . . . . . . . . . . . . . . . 62
Speed dial. . . . . . . . . . . . . . . . . . . . . 26
Star key . . . . . . . . . . . . . . . . . . . . . . . 1
System settings . . . . . . . . . . . . . . . . . 54

T
Talk key . . . . . . . . . . . . . . . . . . . . 1, 22
Telephone jack, pin connections . . . . 62
Text message, see SMS
Tone dialling . . . . . . . . . . . . . . . . 56, 57
Troubleshooting . . . . . . . . . . . . . . . . 58
SMS . . . . . . . . . . . . . . . . . . . . . . . 37

U
Unknown . . . . . . . . . . . . . . . . . . . . . 23
Unknown caller . . . . . . . . . . . . . . . . . 23

V
Viewing the network mailbox
message. . . . . . . . . . . . . . . . . . .
VIP (directory entry) . . . . . . . . . . . . .
Volume
earpiece volume . . . . . . . . . . . . . .
handset speaker volume. . . . . . . . .
ringer . . . . . . . . . . . . . . . . . . . . . .
setting . . . . . . . . . . . . . . . . . . . . .

44
27
52
52
53
53

W
Warning tone, see Advisory tones
Writing (SMS) . . . . . . . . . . . . . . . . . . 31
Writing, editing text . . . . . . . . . . . . . 63
71

Gigaset e490 e495 telephone user guide

Gigaset e490 e495 telephone user guide

More Related Content

What's hot

Similar to Gigaset e490 e495 telephone user guide

More from Telephones Online

Recently uploaded

Gigaset e490 e495 telephone user guide