Implementation of TI-SEPIC Converter for Optimal Utilization Of PV Power

@ IJTSRD | Available Online @ www.ijtsrd.com | Volume – 1 | Issue – 5 | July-Aug 2017 Page: 932
ISSN No: 2456 - 6470 | www.ijtsrd.com | Volume - 1 | Issue – 5
International Journal of Trend in Scientific
Research and Development (IJTSRD)
International Open Access Journal
Implementation of TI-SEPIC Converter for
Optimal Utilization of PV Power
A.S.Valarmathy
Asst.Prof, Prince Shri Venkateswara Padmavathy
Engineering College, Chennai, Tamil Nadu, India
ABSTRACT
In this project qualitative analysis and controller
design of a TI-SEPIC converter for optimal utilization
photovoltaic power is presented. This converter is
essentially combination of conventional buck and
SEPIC converters sharing common components. On
the account of the integration load side only one
inductor is sufficient enough for performing the
power conversion in both Buck and SEPIC
converters. Here the function of the lower SEPIC
converter is to extract maximum power from the PV
and feeds into the load, while the remaining load
power demand is supplied by the dc source through a
voltage-mode controlled buck converter. Proposed
integrated Converter performance is verified through
MAT/SIM software simulations and then verified
with measurement results obtained the laboratory
prototype converter system.
I. INTRODUCTION
High frequency switching converters application in
the dc power distribution is increasing in the recent
years. Particularly in the area of automotive systems
the main focus is on hybrid vehicles. As the power
conversion system is becoming miniaturized,
increasing the power density is one of the challenging
issues for the power supply designers. One of the
main orientations in power electronics in the last
decade has been the development of switching-mode
converters with higher power density and low
electromagnetic interference (EMI). Light weight,
small size and high power density are also some of the
key design parameters. Several different types of
switch-mode dc-dc converters (SMDC), belongs to
buck, boost and buck-boost topologies, have been
developed and reported in the literature to meet
variety of applications. Major concern in the recent
dc-dc distribution systems, such as in automotive and
telecom power supply systems, is to meet the
increased power demand and reduce the burden on the
primary energy source, i.e. built-in battery or ac
utility. This is possible by adding additional power
sources in parallel to the existing battery source. The
additional power sources can be a renewable energy
sources such as photovoltaic (PV) or a fuel cell (FC)
storage power.
In this project a two-input converter which is the
integration of conventional buck and SEPIC converter
(TI-SEPIC) with reduced component count is
considered for the investigations.
Photovoltaic renewable energy source and dc-battery
are the two power sources for the proposed converter.
The input power sources are: conventional dc supply/
battery, and the second one is. The similar kind
approach can easily be extended even to the systems
employing the following
Powering sources: super capacitors, FC, wind, are
their combination. Several controlling methods,
including single loop and multi-loop strategies, have
been reported for the dc-dc converters. Each of these
control schemes has their own advantages and

International Journal of Trend in Scientific Research and Development (IJTSRD) ISSN: 2456-6470
limitations. In this paper a simple and cost effective
single-loop voltage-mode controller is designed for
the buck converter, while perturb and observation
technique is employed for the maximum power point
(MPP) tracking of the TI-SEPIC.
II. BLOCK DIAGRAM
Fig. 1.1 Block diagram of Proposed System
Fig 1.1, the block diagram of proposed system
consists of Buck converter, SEPIC converter, DC
input, solar input, inductance, filter, pulse generator
PID controller and load. Here, the function of SEPIC
converter is to extract power from the solar input and
feed into load, while the remaining load power
demand is supplied by the dc source through buck
converter.
DC input is given to the buck converter and solar
input is given to the SEPIC converter. Buck and
SEPIC converter is integrated by means of
inductance. Because of this integration, only one
inductor is sufficient enough on load side for
performing the power conversion in both buck and
SEPIC converter. Filter is used to remove the
unwanted signals and harmonics. PID Controller will
generate the triggering pulses. Resistive load is used.
III. CIRCUT DIAGRAM
Fig. 3.1 Circuit diagram of Proposed System
Fig 3.1, the circuit diagram of proposed system is
shown. The diode ‘D2’ is common to both the
converters, while the individual converters are having
their own switching devices. Load and its filtering
capacitor are common to both the converters. Hence
the filtering requirement is less as compared to the
individual converter connecting in parallel. The buck
converter is formed by: S1, D1, L1, R, while the
SEPIC converter is formed by: S2, D2, L1, L2, C2, R.
Depending on the location of the PV renewable
energy source and dc-battery in the two input
converter, there are two different power conversion
combinations are possible.The main advantage of this
integrated topology over the integrated topologies
parallel connection at the load terminals is that the
order of the power conversion topology is less by one.
In view of order reduction the dynamical behavior is
somewhat simpler than when it is using two separate
inductors. The circuit can actually operate either in
continuous or discontinuous inductor current mode.
But, its operation in a discontinuous mode of
operation will not provide benefits for the power
conversion, and also on the account of higher power
demand the current flows in ‘L1’ for most loading
conditions. Furthermore, ‘L2’ is designed such that
current is continuous even at lower solar insolations.
Here, the converter switching frequency must be
chosen such that the current in ‘L2’ is continuous even
at lower solar insolations. In view of this the circuit
operation is discussed here only for continuous
inductor current mode (CICM).
IV. SIMULATION AND RESULT
4.1 Simulation block diagram and result for
Open loop control
4.1.1 Simulation Block Diagram

Fig 4.1 Simulink model for open loop control of
Buck-integrated SEPIC converter
In open loop control, a 100V input voltage is given to
Buck converter. Another 100V input voltage which
represents the output voltage of PV module is given to
the SEPIC converter. An output of 135.1V is
obtained. The pulse for the switch in Buck and SEPIC
converter is developed by the following equation.
Where dc is the duty cycle of the switch S1 and dp
is the duty cycle of switch S2.
4.1.2 Simulation Result
Fig 4.2 Simulation result for open loop control of
Buck- integrated SEPIC converter
4.2 SIMULATION BLOCK DIAGRAM AND
RESULT FOR CLOSED LOOP CONTROL
Here also 100V input supply is given to Buck and
SEPIC converter. An output of 135v is obtained. The
pulse for the switch in Buck and SEPIC converter is
developed by PID controller. Reference voltage in the
PID controller is set as 135V.
4.2.1 Simulation Block Diagram
Fig 4.3 Simulink model for closed loop control of
Buck-integrated SEPIC converter
4.2.2 PID controller for Buck-integrated SEPIC
converter
Fig 4.4 PID controller

4.2.3 Simulation Result
Fig 4.5 Simulation result for closed loop control of
Buck- integrated SEPIC converter
V. BENEFITS OF SEPIC CONVERTER
It can be operated in step up or step down mode. It
doesn’t suffer from polarity reversal problem. It has
low amount of EMI due to low input current ripple.
SEPIC converter has high efficiency and non-
pulsating input current.
Nowadays, the use of a DC-DC converter is
widespread in modern electronic equipment and
system. When renewable energy source is used, the
voltage can vary over a wide range. Hence to continue
supplying a constant load voltage, the converter must
be able to work in both buck and boost modes. The
DC-DC converters that meet this operational
requirement are Buck-boost, Cuk, and SEPIC
converters. However, the Buck-boost and Cuk
converters, in their basic form, produce the output
voltage, whose polarity is reversed from the input
voltage. The problem can be corrected by
incorporating an isolation transformer into the
circuits, but this will inevitably lead to the increased
size and cost of the converters. On the other hands,
the SEPIC (Single-Ended Primary Inductor
Converter) converter is capable of operating in both
step-up and step-down modes and does not suffer
from the polarity reversal problem.
Comparison of various Buck-Boost converters is
shown in table 5.1. From that it is clear that SEPIC
converter is more advantageous than others.
Table 5.1 Comparison of Various Buck-Boost
Converters
CONCLUSION
Buck- integrated SEPIC converter suitable for the PV
applications was proposed. A simple and cost
effective open loop and closed loop control is
designed. PID controller is used for the closed loop
control of buck-integrated SEPIC converter Proposed
control scheme effectiveness was analysed and the
following conclusions were drawn: (i) in all these
cases the total load demand is met by the two sources,
(ii) the SEPIC converter is capable of extracting PV
power (iii) dc bus voltage regulation was achieved
and (iv) load changes are reflecting on the fixed dc
source connected through buck converter, while
extracting the available power from the PV source,
which ensures the effective utilization of the
renewable source. Converter performance for the
proposed integrated converter is analyzed through
MATLAB software simulations.
REFERENCES
1. Nicola M. Pearsall and Robert Hill, “Photovoltaic
Modules, Systems and Applications”,
Northumbria Photovoltaic Application Centre
University, Apr 2001.
2. R.Sridhar, Dr.Jeevananathan, N.Thamizh Selvan
and Saikat Banerjee “Modeling of PV Array and
Performance Enhancement by MPPT Algorithm”
International Journal of Computer
Applications,Vol. 7, No.5, Sep 2010
3. Matsuo H., Kobayashi K., Sekine Y., Asano
M.and Lin Wenzhong “Novel Solar Cell Power
Supply System Using theMutip1e-Input D C -DC
Converter” Telecommunications Energy
Conference, Oct 1998.

4. Vuthchhay Eng., Unnat Pinsopon, and Chanin
Bunlaksananusorn “Modeling of a SEPIC
Converter Operating in Continuous Conduction
Mode” Electrical Engineering/Electronics,
Computer, Telecommunications and Information
Technology, 6th International Conference on
May 2009
5. Yaow-Ming Chen, Yuan-Chum Liu, and Sheng-
Hsien Lin “Double-Input PWM DC/DC Converter
for Highnow Voltage Sources” Industrial
Electronics, IEEE Transactions on Oct 2003.
6. Bryan G. Dobbs and Patrick L. Chapman “A
Multiple-Input DC-DC Converter Topology”
IEEE Power Electronics Letters, Vol. 1, March
2003.
7. Hirofumi Matsuo, Wenzhong Lin, Fujio
Kurokawa, Tetsuro Shigemizu, and Nobuya
Watanabe “Characteristics of the Multiple-Input
DC–DC Converter” IEEE Transactions On
Industrial Electronics, Vol. 51, No. 3, June 2004.
8. Luca Solero, Alessandro Lidozzi and Josè
Antenor Pomilio “Design of Multiple-Input Power
Converter for Hybrid Vehicles” IEEE
Transactions On Power Electronics,Vol. 20, No.
5, Sep 2005.
9. S. Yuvarajan, Dachuan Yu and Shanguang Xub
“A novel power converter for photovoltaic
applications” Journal of Power Sources 135
(2004) 327–331.
10. Michael D. Seeman, and Seth R. Sanders
“Analysis and Optimization of Switched-
Capacitor DC–DC Converters” IEEE Transactions
on Power Electronics, Vol.23, No. 2, March 2008.
11. Vuthchhay Eng., Unnat Pinsopon, and Chanin
Bunlaksananusorn “Modeling of a SEPIC
Converter Operating in Discontinuous Conduction
Mode” Electrical Engineering/Electronics,
Computer, Telecommunications and Information
Technology, 6th International Conference on
May 2009.
12. Ruichen Zhao and Alexis Kaminski “Multiple-
input single ended primary inductor converter
(SEPIC) Converter for Distributed Generation
Applications” Energy Conversion Congress and
Exposition, Nov 2009.
13. Gene F. Franklin, J. David Powell, Abbas Emami-
Naeini. Feedback Control of Dynamic Systems.
3rd edition. USA. Addison-Wesley,1994
14. Ogata, K. (2002) Modern Control Engineering 4th
edition. USA Prentice Hall.

Implementation of TI-SEPIC Converter for Optimal Utilization Of PV Power

More Related Content

What's hot (20)

Similar to Implementation of TI-SEPIC Converter for Optimal Utilization Of PV Power (20)

More from ijtsrd (20)

Recently uploaded (20)

Implementation of TI-SEPIC Converter for Optimal Utilization Of PV Power