IRJET- Harmonic Mitigation for Power Quality Improvement using Active Power Filter with Current Control Strategy Under Non-Linear Loads

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 09 | Sep 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 118
Harmonic Mitigation for Power Quality Improvement using Active
Power Filter with Current Control Strategy under Non-Linear Loads
CH. SHANMUKHA RAO1, Dr. G.V. Siva Krishna Rao2
1PG Scholar, Dept. of Electrical Engineering, Andhra University College of Engineering, Visakhapatnam,
A.P, India.
2Professor, Dept. of Electrical Engineering, Andhra University College of Engineering, Visakhapatnam,
A.P, India
-------------------------------------------------------------------------***------------------------------------------------------------------------
Abstract : Application of nonlinear loads are increasing
day by day with advancement of technology. Non-linear
electrical devices has led to a distortion in the output
sine waveforms of source current and voltage. It may
lead equipment (connected to it) to overheat and
sometimes cause damage. This paper concentrates on
better design and application of three-phase shunt active
power filter (SAPF) by using two different methods p-q
theory and d-q theory to mitigate the harmonics which
are created by nonlinear loads. To obtain result for this
paper, the MATLAB / Simulink was used as a simulation
tool. The achieved results are within the recommended
IEEE-519 standard i.e. less than 5% and also the power
factor (PF) of the system to almost unity.
Index Terms: shunt active power filter, power quality,
total harmonic distortion, power factor, UPS ,SMPS,
Nonlinear Loads.
INTRODUCTION
In an electric power system, a harmonic is a
voltage or current at a multiple of the fundamental
frequency of the system, produced by the action of non-
linear loads such as rectifiers, discharge lighting, or
saturated magnetic devices. Harmonic frequencies in the
power grid are a frequent cause of power
quality problems. Harmonics in power systems result in
increased heating in the equipment and conductors,
misfiring in variable speed drives, and torque pulsations
in motors. Passive filters (combinations of capacitors
and inductors) were used to mitigate the PQ problems.
These approaches were extensively used in high voltage
DC transmission (HVDC) for filtering the harmonics on
the AC and DC sides. However, this approach is
unsuitable at the distribution level as passive filters can
only correct specific load conditions or a particular state
of the PS. These filters are unable to follow the changing
system conditions. Thus, the active power filter (APF)
was introduced to compensate harmonics and reactive
power. There are three types of APFs which are shunt
APF, series APF, and hybrid APF (i.e. the combination of
active and passive filters) (Badi, 2012), (Chaughule,
Nehete, and Shinde, 2013).
The purpose of an APF as a power line
conditioner is to repay the utility line current waveform
with the goal that it approximates a sine wave in phase
with the line voltage when a nonlinear load is connected
with the system. Classically, shunt power line
conditioner (shunt passive filter) consists of tuned LC
filters.
OBJECTIVE
The main objectives of this project are To give a
brief overview about the cause and effect of harmonics
in power system To study different types proposed filter
used to eliminate harmonics from the power system .To
study and implement different control strategies already
proposed for modeling of 3 phase shunt active power
filter. To model and simulate three phase shunt active
power filter with different current control strategy in
MATLAB/ SIMULINK environment To compare different
control strategies based on FFT analysis (an important
tool for harmonic behavioral analysis) for harmonic
elimination in power system network.
Passive Filter
It is a combination of series/parallel connection
of passive elements such as capacitors, inductors and/or
resistor. They provide a low resistance path for the
harmonic current to flow owing to the formation of
resonance at that particular harmonic frequency. Hence
harmonic current is diverted through passive filter
network and system current becomes distortion free.
Likewise distortion in voltage waveform is also removed.
For bypassing the current effective means of connection
is connecting the passive filter in parallel with the load.
In order to improve power factor passive filters are
designed as capacitive filter so that it correct the current
displacement factor and provide reactive power to the
load.
Advantages of Passive Filters
Although passive filters doesn’t eliminate
harmonics to a greater extent yet it is used due to some
prominent features which are described as under
1. They are simpler to configure and construct.

2. Low initial & maintenance cost (compared to
APF)
3. Shunt passive filters of capacitive nature
provide reactive power to the nonlinear load and on
the other hand improve power factor by improving
current displacement factor.
4. Lowering of THD in line current to a permissible
limit can be possible by use of passive
Disadvantages of Passive Filters
Some major drawbacks with passive current
filters are:
* Property and characteristics of filter depends on
source impedance (i.e. impedance of the system and its
topology) which are subjected to variations due to
external condition.
* Resonating condition in the filter may create problem
with loads and network leading to voltage fluctuation.
* It basically able to remove some particular harmonic
components through tuning whenever the magnitude
of those harmonic component is constant and pf of the
system is low.
* Filter response is static i.e. if load variation introduce
some new harmonic components then the filter have
to redesigned which increases the maintenance and
operation cost of the filter.
* Load unbalancing or neutral shifting problems can’t
be solved.
Active Filter
An active filter consists of serial/parallel array
of arrangement of both active and passive components
and it is a type of analog electronic filter. Basic building
block of active filter are Amplifiers. Thus filter
performance and response is improved by the use of
amplifiers instead of inductors that are used in passive
filter for the same purpose. Active filter have dynamic
response and thus can remove current distortion,
current harmonics etc. faster than passive filter. It can
also be used for reactive power compensation and also
for voltage based distortions such as flickering, voltage
dip, unbalancing. It uses PWM techniques to remove
load unbalancing and neutral shifting problems. There
is no possibility of resonating condition as tuning of
frequency isn’t taking place in active filtering, so the
power system network remain more stable during
operation. Unlike passive filter, there performance
doesn’t depends on system parameters and its
topology
Operation of Active Filters
Active Filter generate compensating current
signal by continuously monitoring the load current
with the help of some algorithm such as p-q theory, d-q
transform, sliding mode control, DSP based algorithm
etc. Now the generated compensating current is used
to generate the switching pulse and switching
sequence of IGBT inverter with the help of hysteresis
controller or any other type of current controller. The
inverter then generate the required harmonic current
for the load through charging and discharging of DC
link capacitor and injected into the system through
coupling transformer with a phase difference to
compensate the reactive power coming from the AC
mains. Major types of Active filters are: i) Series AF, ii)
Shunt AF and iii) Hybrid AF.
Advantages of Active Filter
1. Widely compensated the THD in source current
waveform.
2. Only a single filter can be able to eliminate all
the unwanted harmonics.
3. Resonance condition is absent which increase
the stability of power system.
4. Filter characteristics changes with load
variation due to dynamic response of the filter.
Shunt Active Power Filter
As the name depicts the shunt active power filter
(SAPF) are connected in parallel to the power system
network wherever a source of harmonic is present. Its
main function is to cancel out the harmonic or non-
sinusoidal current produce as a result of presence of
nonlinear load in the power system by generating a
current equal to the harmonic current but off opposite
phase i.e. with 180ο phase shift w.r.t to the harmonic
current. Generally SAPF uses a current controlled voltage
source inverter (IGBT inverter) which generates
compensating current (ic) to compensate the harmonic
component of the load line current and to keep source
current waveform sinusoidal.

Basic arrangement of SAPF is shown in through block
model.
Compensating harmonic current in SAPF can be
generated by using different current control strategy to
increase the performance of the system by mitigating
current harmonics present in the load current. Various
current control method [2]-[4] for SAPF are discussed
below.
SHUNT ACTIVE POWER FILTER DESIGN
Effect of harmonics
Harmonics in PS can turn into the wellspring of
a mixture of unwelcome impacts. For example,
harmonics can cause signal interference, overvoltage,
data loss, and circuit breaker failure, as well as
equipment heating, breakdown, and harm. Any
dissemination circuit serving modern electronic gadgets
will contain some degree of harmonic frequencies. The
greater the power drawn by nonlinear loads, cause
higher the level of voltage and current distortion as
shown in Figure.
Effect of harmonics on voltage or current waveform
HD in power distribution system can be measured by
using equation (1)
Where n = 2, 3,4,5, ...
APFs are becoming a viable alternative to passive filters
and are gaining market share speedily as their cost
becomes competitive with the passive variety, one of the
most common type of APF to reduce the harmonic
current distortion is SAPF.
Principle of SAPF
The shunt-connected APF, with a self-controlled
dc bus, has a topology similar to that of a static
compensator (STATCOM) used for reactive power
compensation in power transmission systems. SAPF
compensates load current harmonics by injecting equal
but opposite harmonic compensating current. In this
case, the SAPF operates as a current source injecting the
harmonic components generated by the load but phase
shifted by
180°. Figure shows the connection of a SAPF
compensating the harmonic load currents.
Connection of a SAPF.
Instantaneous Real and Reactive Power Theory (p-q
method)
This theory takes into account the instantaneous
reactive power arises from the oscillation of power
between source and load and it is applicable for
sinusoidal balanced/unbalanced voltage but fails for
non-sinusoidal voltage waveform. It basically 3 phase
system as a single unit and performs Clarke’s
transformation (a-b-c coordinates to the α-β-0
coordinates) over load current and voltage to obtain a
compensating current in the system by evaluating
instantaneous active and reactive power of the network
system.The p-q method control strategy in block
diagram form is shown in figure .This theory works on
dynamic principal as its instantaneously calculated
power from the instantaneous voltage and current in 3
phase circuits. Since the power detection taking place
instantaneously so the harmonic elimination from the
network take place without any time delay as compared

to other detection method. Although the method analysis
the power instantaneously yet the harmonic suppression
greatly depends on the gating sequence of three phase
IGBT inverter which is controlled by different current
controller such as hysteresis controller, PWM controller,
triangular carrier current controller. But among these
hysteresis current controlled method is widely used due
to its robustness, better accuracy and performance
which give stability to power system.
Synchronous Reference Frame theory (d-q
method)
Another method to separate the harmonic
components from the fundamental components is by
generating reference frame current by using
synchronous reference theory. In synchronous
reference theory park transformation is carried out to
transformed three load current into synchronous
reference current to eliminate the harmonics in source
current. The main advantage of this method is that it
take only load current under consideration for
generating reference current and hence independent
on source current and voltage distortion. A separate
PLL block it used for maintaining synchronism
between reference and voltage for better performance
of the system. Since instantaneous action is not taking
place in this method so the method is little bit slow
than p-q method for detection and elimination of
harmonics. Figure illustrate the d-q method with
simple block diagram.
P-Q mathematical modelling
The relation between load current & voltage of three
phase power system and the orthogonal coordinates (α-
β-0) system are expressed by Clarke’s transformation
which is shown by the following equation (1)&(2)
[ ]=√ [ √ √
] [ ]………….(1)
[ ]=√ [ √ √
] [ ]…………….(2)
In orthogonal co-ordinate system instantaneous power
can be found out by simply multiplying the
instantaneous current with their corresponding
instantaneous voltage. Here the 3 phase co- ordinate
system (a-b-c) is mutually orthogonal is nature, so we
can found out instantaneous power as in the form of
equation 3.
p = vaia + vbib + vcic ……….. (3)
From above equations, the instantaneous active and
reactive power in matrix form can be rewritten as
[ ] [ ] [ ]……………..(4)
The instantaneous reactive power produces an opposing
vector with 180ο phase shift in order to cancel the
harmonic component in the line current. From the above
equations, yield equation 5.
[ ] [ ] [ ]………..(5)
After finding the α-β reference current, the
compensating current for each phase can be derived by
using the inverse Clarke transformations as shown in
equation 6.
[ ]=√
[
√
√
]
[ ]……………..(6)
D-Q method Mathematical modelling
According to Park’s transformation relation
between three phase source current (a-b-c) and the d-q
reference co-ordinate current is given by equation 7
[ ] √
[ √ √ √ ]
[ ]
………(7)
Where, ‘µ’ is the angular deviation of the synchronous
reference frame from the 3 phase orthogonal system
which is a linear function of fundamental frequency. The
harmonic reference current can be obtained from the load
currents using a simple LPF. The currents in the
synchronous reference system can be decomposed into

two components given by equation 8 & 9
……..(8)
……..(9)
After filtering DC terms (i– , i– ) are suppressed and
alternating term are appearing in the output of
extraction system which are responsible for harmonic
pollution in power system.
The APF reference currents is given by equation 10
[ ] [ ]………(10)
In order to find the filter currents in three phase system
which cancels the harmonic components in line side, the
inverse Park transform can be used as shown by
equation 11
[ ] √ [ ] [ ]……(11)
MATLAB/SIMULINK MODELLING:
Power system Simulink model with Shunt APF and Non-
linear load
System model with filter
Simulink model of Shunt APF with p-q method
Model of Shunt APF with p-q method
Simulink model of Shunt APF with d-q method
Model of Shunt APF with d-q method
Design Parameters for MATLAB Simulation :
Simulation is performed on a balanced Non –Linear Load
consisting of an R-L load and a bridge rectifier as shown
below
 System Parameters
Source Voltage (r.m.s) 400Volt
System Frequency 50Hz
 Active Power Filter (APF) Parameters
Coupling Inductance 1mH
Coupling Resistance 0.01Ω
Dc link capacitance 1100μF
Source inductance 0.05mH
Source resistance 0.1Ω
Load resistance 0.001Ω
Load inductance 1μH

Simulink Result with P-Q control strategy
Breaker Transition Time: - 0.06 sec
Simulation Run Time: - 0.2 sec
Source Voltage Waveform before and after filtering
with p-q method
Source Current Waveform before and after
filtering with p-q method
Load Voltage Waveform before and after
filtering with p-qmethod
Load Current Waveform before and after filtering
with p-qmethod
APF Current Waveform before and after filtering
with p-qmethod
DC link Voltage Waveform before and after
filtering with p-q method
Source Voltage Waveform before and after filtering
with d-qmethod
Source Current Waveform before and after
filtering with d-qmethod

Load Voltage Waveform before and after filtering
with d-qmethod
Load Current Waveform before and after filtering
with d-qmethod
FFT analysis of source current without APF
FFT analysis of source current with SAPF using p-q
method
FFT analysis of source current with APF using d-q
method
System System
without
SAPF
System with
SAPF
using 'p-q'
method
System with
SAPF
using 'd-q'
method
% THD 29.51% 0.69% 0.45%
Table1. Total Harmonic Distortion of System with and
without filter
Conclusion:
The proposed three phase SAPF based on d-q
and p-q current control strategy were simulated in
matlab/simulink for nonlinear loads .The results
successfully validated by observing that d-q showing
better results than p-q current control strategy for
harmonic mitigation.
Future Scope
As the Power Quality is major concerned issue
in this increasing nonlinear load applications, effective
controlling schemes are required for limiting of Power
Quality issue like harmonics hence extension of this
work with much more sophisticated controlling schemes
like Model Adaptive Reference Scheme, and the
modification of PI controllers can be effectively
implemented using with ANN, Fuzzy logic and Algorithm
like Genetic Algorithm.
References
1. Grady, W. Mack, and Surya Santoso.
"Understanding power system harmonics." IEEE
Power Engineering Review 21.11 (2001): 8-11
2. Morán, Luis A., et al. "Using active power filters
to improve power quality." 5th Brazilian Power

Electronics Conference. 1999.
3. M. Suresh , S.S.Patnaik, Y. Suresh, Prof. A.K.
Panda, “Comparison of Two Compensation
Control Strategies for Shunt Active Power Filter
in Three-Phase Four-Wire System”, Innovative
Smart Grid Technology, IEEE PES, 17-19 Jan.
2011, pp. 1 - 6
4. Adam G., Zbant A. and Livint G, 2013. New
Simulink control block for single phase shunt
activepower filters. In 8th International
Symposium onAdvanced Topics in Electrical
Engineering (ATEE),

IRJET- Harmonic Mitigation for Power Quality Improvement using Active Power Filter with Current Control Strategy Under Non-Linear Loads

More Related Content

What's hot (20)

Similar to IRJET- Harmonic Mitigation for Power Quality Improvement using Active Power Filter with Current Control Strategy Under Non-Linear Loads (18)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Harmonic Mitigation for Power Quality Improvement using Active Power Filter with Current Control Strategy Under Non-Linear Loads