Jigs and Fixture
Download as PPT, PDF153 likes87,651 views
The document discusses jigs and fixtures, which are tools used to precisely locate and secure workpieces during manufacturing operations like machining. It defines jigs and fixtures, describes their key elements and principles of location and clamping. It also covers different types of locating and clamping devices as well as common types of jigs like drilling jigs. Jigs are used to guide cutting tools, while fixtures only position and hold the workpiece. Together, jigs and fixtures help improve accuracy, interchangeability and efficiency of mass production.
Jigs and Fixture
- 1. Jigs and fixtures- Applications-differences- Elements of Jigs & Fixtures – Principles of location and clamping – Types of Locating and clamping devices, Types of Jigs and Fixtures Unconventional Machining: Principles of working and applications of USM, AJM, EDM, ECM, LBM and EBM UNIT-VI
- 2. JIGS & FIXTURES Mechanical Engineering department
- 5. • Jigs & Fixtures are special purpose tools which are used to facilitate production in mass scale • They eliminate the necessity of a special set up for each individual part • Jigs & Fixtures provide a means for manufacturing interchangeable parts • They establish a relation between tool and work with pre- determined tolerance. • Once a Jig or fixture is properly set-up any number of same parts may be readily produced without additional set-up.
- 6. Definitions Jig: A device that holds the work and locates the path of the tool. Fixture: A device fixed to the worktable of a machine and locates the work in an exact position relative to the cutting tool. JIG FIXTURE
- 7. Uses of J & F in Manufacturing Industries 1) To reduce production cost 2) To increase production rate 3) To ensure high accuracy in part manufacture 4) To enable heavy and complicated complex shaped parts to be machined by being held rigidly to a machine 5) To provide interchangeability 6) Reduce quality control expenses 7) Less skilled labour & save labour costs 8) Improve work safety
- 9. Economic Viability Analysis And Judging Necessity Of Jig – Fixture The three possible modes of manufacturing a lot of a product by machining are: using ordinary machine and without jig or fixture using ordinary machine but with jig or fixture using automatic special purpose machine The selection of the appropriate mode is governed mainly by, technological feasibility of those modes technical feasibility i.e. availability of the resources and facilities for the different modes economical viability, considering Δ cost of manufacturing, based on ο cost of the basic machine ο cost of the jig or fixture, if to be used ο volume of production (i.e. no. of pieces) ο material and labour cost Δ expected quality of the products and its sale value i.e., revenue Δ total time that will be required to complete the assignment
- 10. Selection of appropriate mode for a specific machining task A specific case for example is taken as follows to illustrate the selection procedure
- 13. Why are they important in Production Locate parts for precision Repeating process on a series of parts Holding parts for machining, painting, assembly
- 14. Basic Elements 1) A sufficiently rigid body (plate, box or frame structure) into which workpiece is loaded. 2) Locating elements 3) Clamping elements 4) Tool guiding elements (for Jigs), Tool setting elements (for Fixtures) 5) Elements for positioning or fastening the jig or fixture on the machine on which it is used
- 15. JIG FIXTURE
- 17. Locating & Clamping The overall accuracy depends on consistent location Location refers to the establishment of relationship between the w/p and Jig or Fixture. Clamping is to hold the work in position inside the Jig/Fixture body so that there is no work movement during maching
- 19. Clamping devices
- 20. Clamping devices
- 21. JIG BUSHES JIG
- 23. FEELER GAUGES
- 24. JIG FIXTURE JIG BODY FIXTURE BODY FIXTURE BOLT
- 25. DIFFERENCES JIG FIXTURE Definition Locates and Holds the work and guides the cutting tool in true position of the work Only Holds & Positions the work, but doesn’t guide the work Elements Work Locating elements, Tool Guiding elements & Work Clamping elements Work Locating elements, Tool setting elements & Work Clamping elements Construction Light Heavy Applications Drilling, reaming , Tapping, Counterboring, Countersinking Milling, Turning, Grinding, Broaching etc., Special features Drill bushes used for tool guiding Feeler gauges, setting blocks to adjust position of tool in relation to work
- 26. Principle of Location (3-2-1 Location principle) WORKPIECE IN SPACE 12 A B C P Q R S D
- 27. A B C D E F WORKPIECE LOCATED IN A JIG/FIXTURE BODY A,B,C,D,E,F – LOCATING PINS JIG/FIXTURE BODY WORKPIECE
- 28. FV TV SV
- 29. Principles of Location 1) The principle of minimum locating points 2) The principle of mutually perpendicular planes 3) The principle of extreme position of pins 4) Relief should be provided where burr or swarf will get collected 5) Locating surface should be raised above the surrounding surfaces of J/F so that chips can be swept off readily. 6) Sharp corners in the locating surfaces must be avoided 7) Adjustable type locators to be used for rough surfaces
- 30. WORK WORK LOCATORS Locators at short distance Locators widely displaced Ø Ø Ø= Angle of Error CASE-1 CASE-2 The principle of extreme position of pins
- 32. Locators above surface Adjustable type Locators
- 33. Locating Devices The pins of various design and made of hardened steel are the most common locating devices used to locate a work piece in a jig or fixture. The shank of the pin is press fitted or driven into the body of jig or fixture. The locating diameter of the pin is made larger than the shank to prevent it from being forced into the jig or fixture body due to the weight of the work piece or cutting forces. Depending upon the mutual relation between the work piece and the pin. The pin may be classify as follows: (1) Locating Pins (2) Support Pins (3) Jack Pins Locating Pins When reamed or finally finished holes are available in work piece, these can be used for locating purpose. these are two types of locating pins: • Conical locating pins • Cylindrical locating pins
- 35. (2) SUPPORT PINS
- 37. PRINCIPLES OF CLAMPING 1) The clamping pressure applied against the workpiece must counteract the tool forces 2) The clamping pressure should not be directed towards the cutting operation. Wherever possible it should be directed parallel to it. 3) The clamping pressure must not damage/deform the work surface. 4) Clamps should be arranged directly above the points supporting the work, otherwise distortion of work may occur. 5) Clamping pressure should be directed towards the points of support, else the work will tend to rise from support 6) Clamping should be simple, effective and foolproof. 7) Fibre pads should be riveted to clamp faces to avoid damage to fragile workpieces
- 40. If the work piece can not be restrained by the locating devices or elements, it become necessary to clamp the work piece in jig or fixture body. The most common example of clamping devices is bench vice. The purpose of the clamping is to exert a pressure to press a work piece against the locating surfaces and hold it there in a position to the cutting forces. In bench vice the movable jaw of the vice exert force on the work piece , their by holding it in correct position of location in the fixed jaw of the vice. The commonly used clamping devices are follows: (A): Clamping Screws: Clamping screws are used for light clamping. Clamping screws are shown in fig. CLAMPING DEVICES
- 42. (B): Hook Bolt Clamp: This is very simple clamping device and is only suitable for light work and where usual tip of the clamp is inconvenient. The typical hook bolt clamp is shown
- 43. (C): Bridge Clamp: It is very simple and reliable clamping device. The clamping force is applied by spring loaded nut.
- 44. (D): Heel Clamp: These consists of a rested plate, center stud and heel. This trap should be strengthen at the point where the hole for the stud is cut out, by increasing the thickness around the hole. The design differ from simple bridge clamp in that a heel is provided at the outer end of the clamp to guide its sliding motion for loading and unloading the work piece.
- 45. (E): Swinging Strap(Latch Clamp): This is a special type of clamp which provides a means of entry for loading and unloading the work piece. For this the strap(latch or lid) can be swing out from the work piece. The typical swing strap or latch clamp is shown in figure.
- 46. F): C-Clamp: To unload the work piece, the locking nut is unscrewed by giving it about one turn and this releases the c- clamp. When the clamp is removed or swing away the work piece can freely pass over the nut. Reverse procedure is adopted for loading the work piece.
- 47. Design principles Common to Jigs and Fixtures There are some principles which are useful to design jigs and fixtures. 1: Rigidity: Jigs and fixtures should be sufficiently stiff to secure the preset accuracy of machining. 2: Fool proofing: It can be defined as “ the incorporation of design feature in the jig or fixture that will make it impossible to lead the work into jig and fixture in an improper position” There are many fool proofing devices , such as fooling pegs, blocks or pins which clears correctly position parts but prevent incorrectly loaded parts from entering the jig and fixture body. 3: Clearance: Clearance is provided in the jig or fixture body (A) to allow for any variation in component sizes specially casting and forging. (B) To allow for hand movements so that the work piece can easily placed in the jig or fixture and removal after machining .
- 48. FOOL PROOFING OF A FIXTURE
- 50. 5: Ejectors: The use of ejection devices to force the work piece out from the jig or fixture is important in two positions. (A) the work piece is heavy (B) machining pressure forces the work piece to the slides or based on the jig or fixture and the pressure and oil or coolant fill will cause the work to strick and difficult to remove on small jigs and fixtures , a pin located under the work will remove the part radially.
- 52. Types Of Drilling Jigs Drilling jigs may be classified as follows: 1. Template jig 2. plate type jig 3. Open type jig 4. Channel jig 5. Leaf Jig 6. Box type jig
- 53. 1: Template Jig: This is the simplest type of jig; It is simply a plate made to the shape and size of the work piece; with the require number of holes made it. It is placed on the work piece and the hole will be made by the drill; which will be guided through the holes in the template plate should be hardened to avoid its frequent replacement This type of jig is suitable if only a few part are to be made.
- 54. 2: Plate Type Jig: This is an improvement of the template type of jig. In place of simple holes, drill bushes are provided in the plate to guide the drill. The work piece can be clamped to the plate and holes can be drilled. The plate jig are employed to drill holes in large parts, maintaining accurate spacing with each other.
- 55. 3:Open Type Jig: In this jig the top of the jig is open; the work piece is placed on the top.
- 56. 4 Channel jig; The channel jig is a simple type of jig having channel like cross section. The component is fitted within the channel is located and clamped by locating the knob. The tool is guided through the drill bush.
- 57. 5: Leaf Jig: It is also a sort of open type jig , in which the top plate is arrange to swing about a fulcrum point , so that it is completely clears the jig for easy loading and unloading of the work piece. The drill bushes are fitted into the plates , which is also known as leaf , latch or lid.
- 58. 6: Box Type Jig: When the holes are to drill more than one plane of the work piece , the jig has to be provided with equalant number of bush plates. For positioning jig on the machine table feet have to be provided opposite each drilling bush plate. One side of the jig will be provided with a swinging leaf for loading and unloading the work piece, such a jig would take the form of a box. Such a jig should be as light as possible. Since it will have lifted again and again. Typical figure of box type jig is shown: