K045047377

Edathil Telwin George et al Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 4, Issue 5( Version 4), May 2014, pp.73-77
www.ijera.com 73 | P a g e
Capacitive Touch User Interface and Implementation with
Virtual Refrigerator
Edathil Telwin George
MIT Academy of Engineering Global Technology and Engineering centre, Whirlpool of India Ltd. Pune, India
Abstract
The proposed User Interface incorporates 14 Touch keys, including slider and wheeler functionality using self
capacitance technology, 24 side throw LED with intensity controlled Fade-IN, Fade-OUT effects, Buzzer chime,
Voltage regulator circuit, and communication circuitry for the control board. The major advantage that this User
Interface is that the entire assembly is less than 10mm thick including PCB, components, light guide and
graphics sticker. In this project the mentioned capacitive touch user Interface is interfaced with a Lab view
system simulating a virtual refrigerator capable of responding to the commands from the User Interface.
Keywords—User Interface, self capacitance, Light guide, Lab view, LED driver, Buzzer, Human Machine
Interface (HMI).
I. INTRODUCTION
The User Interface is the part of the system a
consumer or intended operator has access to in order
to control the various functions the product is capable.
Figure 1 Current trends in User Interface
As shown in figure 1 a good user Interface is
an integral part of various products we see around us
like Automobiles, phones, computers, television,
music systems home appliances etc. The user
interface may also provide the user with audio visual
indications in order to convey different states and
modes. The User Interface has gained increasing
importance in the field of HMI (Human Machine
Interface). In the field of home appliances HMI is
enhanced in terms of flush finish boards, touch keys,
gesture recognition, polyphonic tones, glass front
aesthetics, Wi-Fi or NFC compatibility, Smartphone
compatible etc to name a few notable feature. A good
user interface providing functionality and aesthetics is
one of the core ingredients to achieving optimum
standards in HMI. A good user interface also aims at
making the product more user friendly and thereby
enhancing the user experience with the product.
Labview is a system developed by National
Instruments which is widely used in the field of
automation. Labview provides ease of creation of a
virtual system that is completely programmable and
capable of establishing via a wide range of protocols.
Thus Labview system is capable of efficiently
simulating system behavior and generating required
control actions. Lab view can be used to generate. A
virtual system provides a distinct advantage providing
cadence to whole set of features.
II. LITERATURE SURVEY
A. Market Survey
The User Interface in this project is targeted
for the refrigeration market in India. A range of
refrigerators available in India by a variety of
manufacturers were reviewed to have a comparative
analysis. We can see that refrigerators on the whole
lack in terms of user experience. Most models are
pretty basic and are farfetched from the use of latest
available technologies Thus from the range of
products in India we have seen that these products do
have a lot of features but lack in terms of User
Interface experience. Traditional lighting systems are
done using LEDs with either ON/ OFF modes. In
order to enrich the aesthetics it is necessary to make
use of varying light intensities. The products with the
enhanced user Interface are mainly imported from U.
S and European markets and therefore available only
at a steep price. Hence when it comes to User
Interface for refrigerators in India there is a significant
scope of improvement.
The major road block hampering the
introduction more enhanced Human machine
Interface is the heavy cost that comes with it A system
like a capacitive touch user Interface also faces
technical challenges due to the space constraints on
RESEARCH ARTICLE OPEN ACCESS

the refrigerator doors in India. The conventional touch
assembly is pretty thick as shown in Fig 2 which
could result in reduced cooling insulation at the
respective position thereby causing cooling loses as
well as result in condensation on the electronic board.
Thus the proposed slim UI assembly as shown in Fig.
3 overcomes a lot a lot of manufacturing and
performance issues. (Figures are taken from the
software : Expedition PCB 3D viewer)
Figure 2 Conventional UI Assembly
Figure 3 Proposed SLIM UI
B. Current trends in User Interface test set-up
In Whirlpool Corporation in order to test a
user Interface and its interaction with the product
currently it is required to have the specific control
board that it would be used with an actual product
capable of interfacing with the said control board as
well as the user interface. With the number of
different control boards available throughout the
entire product range as well as different products
available would make it an extremely large set of
combinations to stock. Ideally a user Interface to be
marketed in the North America would be tested by the
software testing team in India. This would require
them to not only ship the User Interface but also the
specific control board as well as the product if the
overall behavior needs to be ensured.
C. Possible touch solutions
1> A Touch Sensing Controller IC Adopting
Differential Measurement
A touch sensor controller IC proposed by
Stojanovic R et al. [1] with a novel touch sensing
scheme is proposed for projected capacitive
touch panel. The
IC adopts the differential measurements to amplify the
capacitance variation. By using the scheme,
sensitivity to a touch object is increased and the
immunities to power noise and display noise are
improved.
2> FPGA Based Capacitive Touch Pad
A technique proposed by Siwei Zhana et al.
[2] have introduced sensing principle
and FPGA design of a capacitive touch pad/interface
where the sensing pad is connected to the I/O pin via
an external resistor. The circuit transforms the change
in pad capacitance into voltage amplitude during
charging, discharging and sharing phases. By using
multiple pins and resistors, a multi touch system is
achieved.
III. PROPOSED SYSTEM
Figure 4 Block Diagram
D. Labview Set-up.
The Lab View set-up [6] would give a
graphical representation of the entire refrigeration
system consisting of the user Interface, Compressor
Heater, Freezer temperature, Refrigerator
compartment temperature. This system would be
capable of handling and responding to commands sent
by the user Interface.
E. Micro controller
The Touch panel microcomputer R8C/33T
group contains a hardware peripheral (SCU: sensor
control unit) that monitors the”touch” of the human
body by measuring the stray capacitance generated
between the touch electrode and the human. The
Renesas R8C/33T Group [3] of single-chip MCUs
incorporates the R8C CPU core, employing
sophisticated instructions for a high level of
efficiency. Renesas micro has 1 Megabyte of address
space and it is capable of executing instructions at
high speed. In addition, the CPU core boasts a
multiplier for high-speed operation processing. Power
consumption is low, and the supported operating
modes allow additional power control.

F. Touch Interface
As shown in Figure 5 there are different
forms of touch keys, Touch screens
Figure 5 Types of Touch Interface
The touch pad principle used for this project
makes use of electrostatic capacitance method is the
general principle used in “Touch” measurements. The
touch electrode is formed with materials such as PCB
(printed circuits board), ITO (Indium Tin Oxide) films
and electro conductive rubbers. The electric
capacitance generated between the touch electrode
and the human body is measured and a key ON or
OFF judgment is made. When a lot of keys are
necessary, the matrix configuration is used. The touch
key matrix is like the key scanning matrix used with
mechanical switches. When detection of movement of
the finger that is the top to bottom or right and left is
desired, the slider is used, and when the detection of
movement around the circumference is desired, the
wheel is used.
G. Touch Interface
The LED driver is basically used to control
the LEDs without loading the micro-controller. The
LED driver needs to have smooth Pulse Width
Modulation control in order to have smooth control
over LED intensity. The driver would typically have
I2C protocol for communication with the micro-
controller.
H. Touch Interface
The power to the User Interface would
typically be delivered by the control board. The user
Interface is required to have onboard voltage regulator
provision to be compatible over a wide voltage range.
I. Touch Interface
Wide communication is a whirlpool
proprietary communication protocol used for Inter-
board communication. This interface carries signals
coming from standard microcontroller asynchronous
port (SCI or UART) and is designed to connect boards
in a single line wired-OR bus. This interface has
capability to carry up to 9600 baud.
IV. HARDWARE IMPLEMENTATION
A. Touch Implementation.
The self capacitance method [3] of touch
detection is used by the Renesas R8C/33T controller.
Figure 6 shows the principle of the self capacitance
detection method. When not touched, a parasitic
capacitance exists in touch electrode between the
GND pattern and metallic frame of the PCB around
the electrode. The electric capacitance is generated
between the touch electrode and the finger because
the human body is a conductor which is grounded to
virtual GND so when the finger approaches the
capacitance increases. The self-capacitance detection
method perceives the approach of the finger by
measuring an increase in the electric capacitance
between non-touch and touch conditions. The self-
capacitance method structure is simple, but because
wiring to the electrode and the measurement IC
cannot be protected by the GND pattern, the noise
tolerance is low.
Figure 6 Self Capacitance Method
J. Touch sensing Within The Renesas
Controller
Figure 7: shows the method of voltage
division by series capacitance (OMRON method).
This method measures the electric capacitance of Cx
by the following methods.
Capacitor Cc is charged then is gradually
discharged through resistance Rc. The charge of Cc is
moved to the comparison capacitor Cr and the electric
capacitance Cx. The divided voltage of Cr and Cx is
measured. A detailed measuring method is as follows.
SW1 is assumed turning on and Cc is charged.
(SW2,SW3 is OFF) SW1, SW2, and SW3 are turned
off. The charge of Cc is maintained. SW2 and SW3
are turned on for a fixed time. Cc is partially
discharged through resistance Rc while all the charge
on Cx and Cr are discharged.
SW1, SW2, and SW3 are turned off. The
charge of Cc moves to Cx and Cr. The voltage of Cx
is compared with Vref with a comparator. The

relationship of voltages Vr, Vc,,Vx and capitances,
Cc, Cr, and Cx are as follows.
Figure 7 Fundamental Touch sensing circuit
Figure 8: shows a typical wave outline when
touch detection operates. The rectangular shape waves
shows changing voltage of Cx, and a mountain shape
of waves is changing voltage of Cc. Voltage Vc
decreases gradually as above-mentioned steps (3), (4),
and (5) are repeated. Voltage Vx is the voltage shown
by equation (c) in step (4), and 0V in step (3) since
switch SW3 is closed. The number of cycles to reach
Vx<Vref decreases when the capacitance of Cx
increases by touch. The number of cycles is used to
judge non-touch or touch.
Figure 8 Touch Sensing cycles
The electric capacitance generated in man's
finger and electrode is a few pF. A large value will
provide an accuracy improvement of the touch
detection if it is possible to improve it. However, the
electrode surface area is related to the touch area of
the finger and it is not effective to increase the area
past some value. The inter electrode distance depends
on thickness of the material with which the surface of
the touch key is covered. Table 1 shows the relative
permittivity of some common materials. It is different
according to each material. The glass has the best
relative permittivity excluding water. Acrylic and
plastic are also often used
Table 1 : Relative Permittivity of materials.
V. PROPOSED GRAPHICS
The proposed graphics is illustrated in Figure
7
Figure 9: Proposed Graphics
The product is capable operating in the
following modes.
Quick Ice
Bottle cool
Garden Fresh
Vacation
Low, Mid, High & Auto
Each user mode has a specific temperature
set point, Compressor run time best suited for each of
the particular applications. The exact product level
temperature set-points and timing details are yet to be
confirmed.
VI. LIGHT GUIDE AND LED PLACEMENT
Figure 10: Light Guide and LED Placement.
For this particular project we would be using
side fire LEDs in an attempt to accomplish the overall
slim design. As shown in Figure 8 we can see the
LED placement and the light rays shown as segments
from the LED. The boundaries between icons show
the final placement of light guide assembly. The Light
guide contains light refracting particles at desired
locations to refract light in order to illuminate the
icons.
VII. RESULTS
The touch User Interface works as desired
but an few software tweaks are required to adjust the
sensitivity and touch response. The adjustment is to be
made so as to accommodate the variations introduced
by touch from different people. The LEDs driven by
the LED driver, work with the required Fade-IN and
Fade- OUT effect. The Buzzer chime is also a
functional part of the User Interface.
Minimal Labview setup is done in order to
simulate the virtual environment. The User Interface
model is functional as an Individual model on the
virtual system. At present work is in progress to
communication between the User Interface and the
Labview set-up.

VIII. CONCLUSION
The intended capacitive touch User Interface
includes the Touch module, LED driver, Buzzer
module, Communication circuitry and the on board
voltage regulator within the estimated target costing.
The Overall thickness of the complete assembly is
expected to be less than 10mm. The product only
requires a small cavity for the board to fit in and has
sufficient room for the foam. This helps the
installation without any loss in cooling.
The Virtual refrigerator will be able to
simulate a host of control boards with minor changes.
Thus the virtual system significantly improves the
flexibility of the test equipment.
IX. ACKNOWLEDGMENT
The project is sponsored and supported by
Global Technology and Engineering Centre,
Whirlpool of India Ltd. Under the guidance Mrs.
Usha Verma, MIT Academy of Engineering.
References
[1] Stojanovic R, Lekic, N, Mijanovic, Z
& Kovacevic, J, „FPGA based capacitive
touch pad/interface‟, Electronics and
Nanotechnology (ELNANO), 2013 IEEE
XXXIII International Scientific Conference
[2] Siwei Zhan, Tingcun Wei, Bo Li, Wei Liu,
& Qimeng Chen], „A Touch Sensor
Controller IC Adopting Differential
Measurement for Projected Capacitive
Touch Panel Systems‟ 2012 © Chengdu].
doi: 10.1109/CIT.2012.106
[3] Renesas application Note:
R01ANxxxxEJ0603 Rev 1 July 6, 2012
[4] STMicroelectronics. Available:
http://www.st.com/st-web-
ui/static/active/en/resource/technical/docum
ent‟/datasheet/DM00039926.pdf
[5] Atmel Feb 2009. Available:
http://pdf.datasheetarchive.com/indexerfiles/
Datasheet-092/DSA0048597.pdf
[6] Lab View Basics by Hans-Petter Halvorsen
20th April 2012:
http://home.hit.no/~hansha/documents/labvi
ew/training/Introduction%20to%20LabVIE
W/Introduction%20to%20LabVIEW.pdf
[7] ISSI LED Driver datasheet July 2012:
http://www.issi.com/WW/pdf/31FL3236.pdf
[8] PCA9622 16-bit Fm+ I2C-bus 100 mA 40 V
LED driver datasheet Rev. 4, 6 September
2012
http://www.nxp.com/documents/data_sheet/
PCA9622.pdf
[9] ST Microelectronics LED1642GW
datasheet preliminary release.
http://www.st.com/st-web-
ui/static/active/en/resource/technical/docum
ent/datasheet/DM00080246.pdf
[10] ST Microelectronics LED1642GW
datasheet preliminary
http://www.st.com/web/en/reso
urce/technical/document/datasheet/CD00237
442.pdf

K045047377

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to K045047377 (20)

Recently uploaded (20)

K045047377