Losses in Pipe
Download as PPTX, PDF2 likes5,159 views
Unit 6 discusses losses in pipes, including major and minor losses. Major losses are due to friction and calculated using Darcy-Weisbach or Chezy's formulas. Minor losses are due to changes in pipe direction, size, or obstructions and are also calculated using specific formulas. The document also discusses equivalent pipes, pipes in series, pipes in parallel, and two and three reservoir pipe flow analysis problems. Head losses are calculated using friction and minor loss formulas, and continuity and energy equations are used to analyze pipe flows.
Losses in Pipe
- 1. Unit-6: Losses in Pipes SYLLABUS: A. Major and Minor Losses, Darcy-Wiesbach Equation, Concept of Equivalent Pipe, Dupit’s Equation. B. Pipes in Series, Parallel and Syphon, Two Reservoir Problems, Three Reservoir Problems Concept of Water hammer. Surge Tanks (Function, Location and Uses).
- 2. FLOW THROUGH PIPE • A pipe is a closed conduit (generally of circular section) which is used for carrying fluids under pressure. The flow in a pipe is termed pipe flow only when the fluid completely fills the cross-section and there is no free surface of fluid. The pipe running partially full (in such a case atmospheric pressure exists inside the pipe) behaves like an open channel.
- 3. LOSS OF ENERGY (OR HEAD) IN PIPES • When water flows in a pipe, it experiences some resistance to its motion, due to which its velocity and ultimately the head of water available is reduced. This loss of energy (or head) is classified as follows : A. Major Energy Losses • This loss is due to friction. B. Minor Energy Losses • These losses are due to : 1. Sudden enlargement of pipe, 2. Sudden contraction of pipe, 3. Bend of pipe, 4. An obstruction in pipe, 5. Pipe fittings, etc.
- 4. MAJOR ENERGY LOSSES • These losses which are due to friction are calculated by : 1. Darcy-Weisbach formula 2. Chezy’s formula.
- 7. Chezy’s Formula for Loss of Head due to Friction
- 12. Minor Losses
- 13. • Loss of Head due to Sudden Enlargement • Loss of Head due to Sudden Contraction
- 14. • Loss of Head due to Obstruction in Pipe • Loss of Head at the Entrance to Pipe
- 15. • Loss of Dead at the Exit of a Pipe • Loss of Head due to Bend in the Pipe
- 16. • Loss of Head in Various Pipe Fittings
- 17. Equivalent Pipe • Equivalent pipes refer to imaginary pipes which are used to determine the head loss and flow of discharge considering that the flow of discharge and head loss in the actual piping system is same as that of the equivalent pipe. It is a technique used to decrease the large number of attached pipe systems into an individual pipe system such that the piping system analysis can be made easier. • In equivalent pipe structure, the major properties of pipe such as length of pipe, diameter of pipe and roughness factor of pipe are required to do the analysis.
- 22. 4.6 Pipe Flow Analysis •Pipeline system used in water distribution, industrial application and in many engineering systems may range from simple arrangement to extremely complex one. •Problems regarding pipelines are usually tackled by the use of continuity and energy equations. •The head loss due to friction is usually calculated using the D-W equation while the minor losses are computed using equations depending on the appropriate conditions.
- 23. 4.6.2 Pipes in Series ▪ When two or more pipes of different diameters or roughness are connected in such a way that the fluid follows a single flow path throughout the system, the system represents a series pipeline. ▪ In a series pipeline the total energy loss is the sum of the individual minor losses and all pipe friction losses. Pipelines in series
- 24. ▪ Referring to Figure the Bernoulli equation can be written between points 1 and 2 as follows; where P/ρg = pressure head z = elevation head V2/2g = velocity head HL1-2 = total energy lost between point 1 and 2 Realizing that P1=P2=Patm, and V1=V2, then equation reduces to z1-z2 = HL1-2 Or we can say that the different of reservoir water level is equivalent to the total head losses in the system. The total head losses are a combination of the all the friction losses and the sum of the individual minor losses. HL1-2 = hfa + hfb + hentrance + hvalve + hexpansion + hexit. Since the same discharge passes through all the pipes, the continuity equation can be written as; Q1 = Q2
- 25. 4.6.3 Pipes in Parallel Pipelines in parallel • A combination of two or more pipes connected between two points so that the discharge divides at the first junction and rejoins at the next is known as pipes in parallel. Here the head loss between the two junctions is the same for all pipes.
- 26. ▪ Applying the continuity equation to the system; Q1 = Qa + Qb = Q2 ▪ The energy equation between point 1 and 2 can be written as; ▪ The head losses throughout the system are given by; HL1-2=hLa = hL ▪ Equations are the governing relationships for parallel pipe line systems. The system automatically adjusts the flow in each branch until the total system flow satisfies these equations.