Low power 6 transistor latch design for portable devices

Innovative Systems Design and Engineering www.iiste.org
ISSN 2222-1727 (Paper) ISSN 2222-2871 (Online)
Vol 3, No 5, 2012

Low Power 6-Transistor Latch Design for Portable Devices
Abhilasha1, *K.G.Sharma2, Tripti Sharma2 and Prof.B.P.Singh1
Deptt. of Electronics and Communication Engg., FET-MITS Lakshmangarh, Rajasthan (India)
Suresh Gyan Vihar University, Jagatpura, Jaipur, Rajasthan (India)
*sharma.kg@gmail.com

Abstract
The latest advances in mobile battery-powered devices such as the Personal Digital Assistant (PDA) and
mobile phones have set new goals in digital VLSI design. The portable devices require high speed and low
power consumption. Even low power consumption is the dominant requirement and to do so speed can be
compromised. In this paper a novel area efficient latch design is proposed. The simulation results show that the
proposed design with less transistor count is better choice for low power and high speed portable applications.
Keywords: Latch, Low power, Portable, 8T, 6T, Power consumption, Delay.

1. Introduction
Advances in CMOS technology have led to a renewed interest in the design of basic functional units for low
power, high speed, small area, longer battery life and more reliable systems. This tremendous demand is due to
popularity of battery-operated portable equipments such as personal computing devices, wireless
communication, medical applications and other portable devices.
The design of high-speed and low-power VLSI architectures needs efficient arithmetic processing units, which
are optimized for the performance parameters, namely, speed and power consumption [1][2].
Device design in VLSI is being motivated by three basic goals, viz. minimizing the transistor count,
minimizing the power consumption and increasing the speed. Using less number of transistors is beneficial in
reducing the number of components, interconnect parasitic capacitances, chip area, propagation delay and
potentially lower power consumption.
Sub-threshold digital circuits are suitable for the specific applications, which need high performance clubbed
with low power consumption. This type of application includes medical equipments such as hearing aids and
pace maker, wearable wrist-watch computation and self powered devices. It can also be applied to applications
in which the circuit remains idle for an extended period or to portable applications which cannot carry heavy
batteries. Sub-threshold current of MOSFET transistor occurs when the gate-to-source voltage (VGS) of a
transistor is lower than its threshold voltage (VTH). When VGS is lower than VTH, there are less minority
carriers in the channel, but their presence comprises a current and the state is known as weak-inversion. In
standard CMOS design, this current is a sub-threshold parasitic leakage, but if the supply voltage (VDD) is
lowered below VTH, the circuit can be operated using the sub-threshold current with ultra-low power
consumption [3][4]. In sub-threshold region, the drain current IDS is exponentially related to the gate voltage
VGS as shown in equation 1.

(1)

68

Vol 3, No 5, 2012

Where, , and VTH is the thermal voltage. For VDS > 3VTH, IDS becomes independent of
VDS for all practical purposes. In digital design, the near-ideal current source characteristic improves the noise
margin of the circuits.
The total energy dissipation ET of static CMOS circuits operating in sub-VT regime is modeled as

(2)

(3)
Where, Edyn, Eleak, and Esc are the average energy dissipation due to switching activity, the energy
dissipation resulting from integrating the leakage power over one clock cycle Tclk, and the energy dissipation
due to short circuit currents, respectively. The energy dissipation Esc has been shown to be negligible in the
sub-VT regime [5]. The dynamic and leakage power dissipation is only results from sub-threshold currents [6].
The dynamic power dissipation, since the input and the supply voltages are less than the threshold voltage of
the transistor, is also very less as compared with the super-threshold operation of the device.
The critical path delay in CMOS devices is given by [7]

(4)
Where, kcrit is the critical path delay, n denote the slope factor and VT the thermal voltage. Thus from equation
3 and 4, the total energy dissipation ET assuming operation at the maximum frequency is

(5)
It is found that the sub-VT model predicts the energy dissipation with less than 3.8% error [8].
Flip flop and Latch are the most commonly used sequential elements whose purpose is synchronizing data
signals. A latch is a three-terminal element, having two inputs, data (D) and clock (clk) and one output (Q). For
timing requirements, level sensitive latches are widely used in high performance ICs where timing analysis is
more critical and challenging. The conventional edge-triggered flip-flop (FF) design methods using clock
synchronization are very practical, since only the timing constraints defined by a given clock frequency are
optimized. However, clock skew that has a strong influence on clock frequency design prevents the FF design
because of the variations. Thus, level-triggered latch design method has been proposed as alternatives to
FF-based design methods.
There are three main sources of power dissipation [9] in the latch:
• Internal power dissipation of the latch, including the power dissipated for switching the output loads
• Local clock power dissipation, presents the portion of power dissipated in local clock buffer driving the clock
input of the latch
• Local data power dissipation, presents the portion of power dissipated in the logic stage driving the data input
of the latch
Total power parameter is the sum of all three measured kinds of power.

69

Vol 3, No 5, 2012

This paper is organized as follows: Section 2 describes the existing eight transistor (8T) latch reported in the
literature. Section 3 describes the design and functionality of proposed six transistor (6T) latch. Simulation
results, comparisons and layouts are presented in Section 4 and finally Section 5 draws the conclusion.

2. Latch Design
2.1. Conventional 8T design
The conventional 8-transistor latch design [5] uses transmission gate logic (Figure 1). The output Q assumes
the value of the input D, when the clock is active, i.e. for CLK=1. When the clock signal goes to zero, the
output will simply preserve its state [10]. Thus the clock acts as an enable signal which allows data to be
accepted into the D-latch.
This circuit basically contains two inverter loop and two transmission gate (TG) switches. The TG at the
feedback loop is activated when CLK signal low. Thus the input is accepted (latched) into the circuit when the
CLK is high, and the information is preserved as the state of the inverter loop when the CLK is low. The 8T
latch is positive level triggered.

2.2. Proposed 6T design
The basic idea behind the proposed design is to replace transmission gate logic by pass transistor logic in
conventional 8T design. The proposed 6-transistor design implements pass transistor logic for the transmission
of data through it. The drain of first transistor PMOS_1 are connected to the data input and this data will be
available at the drain terminal only when the clock will be low (Figure 2.)
Since PMOS transistors are weak zero transistors, so small threshold loss is observed when data is zero. The
output of this transistor is connected to the input of the first inverter. This inverter then inverts this data and also
compensates the threshold loss, but not completely and thus less than the desired output loss is observed at the
output. The next inverter again inverts the data and produces the output ‘Q’. This output is feedback to the
transistor NMOS_1.But overall performance of the device is almost unaffected because of the presence of the
inverters.
The transistor NMOS_1 passes the output according to the delayed version of the clock. Thus whenever clock
is high, data is not passing through the transistor PMOS_1 but output is again feedback through the circuit and
output remains same. Thus this proposed clocked latch acts as a negative level triggered flip flop. Whenever,
clock is negative, the output changes with respect to data but remains constant as clock goes positive.

2.3. Layout designs of the conventional and proposed latches
Integrated circuit (IC) layout is the representation of an IC in terms of planar geometric shapes, which
correspond to the patterns of metal, oxide and semiconductor layers that make up the components of an IC.
Layout is the process by which a circuit specification is converted to a physical implementation with enough
information to deduce all the relevant physical parameters of the circuit. The layout step is the last major step in
the design process before testing and fabrication.
The layout design for the conventional 8T latch is shown in Figure 3. In the layout design of the conventional
8T latch, number of poly contacts is two and number of poly and metal overlap is only one.

70

Vol 3, No 5, 2012

The layout design for the proposed 6T latch is indicated in Figure 4. The substrate terminals of all the circuits
are connected to their respective source terminals in order to nullify the substrate-bias effect. In the layout
design of the proposed 6T latch, number of poly contacts is two but there is no poly and metal overlapping, the
reduction in poly contacts and poly and metal overlap leads to reduce power consumption and delay to some
extent and hence significant reduction in PDP take place.

The designed layouts of conventional and proposed latches are used to extract the parasitic capacitances. The
Total numbers of parasitic capacitance are six in both the designs, which are having value more than 1fF. DRC
is performed to validate a high overall yield and reliability of the design. LVS check confirms that shorts, opens,
component mismatches, and missing components are not found.

3. SIMULATION AND COMPARISON
All schematic simulations are performed on Tanner EDA tool version 13.0 at 65nm and 45nm technology. The
aspect ratio for all the transistors is 1 for both the designs (W/L = 1). The power supply VDD and the input
voltages are kept below the threshold voltage of the MOS transistors to ensure that all the transistors are indeed
operating in the sub-threshold region.
After the physical layout designing post-layout simulations are carried out with extraction of parasitic
capacitances. Power consumption is a function of load capacitance, frequency of operation, and supply voltage.
A reduction of any one of these is beneficial. The reduction in any one of power consumption and delay
provides several benefits. Less heat is generated, which reduces problems associated with high temperature,
such as the need for heat sinks. An additional benefit of the reduced power consumption is the extended life of
the battery in battery powered systems. Table 1 shows significant reduction in total capacitance as well as
output parasitic capacitances. The capacitance values are obtained after layout simulation.
From this comparison, it is clear that both output capacitance and total parasitic capacitance for proposed
design is lower than conventional design which is desirable for low power consumption and less delay, as
power consumption is directly proportional to capacitance, therefore proposed design is having reduction in
power consumption, i.e., useful for low power applications.
The input-output waveforms are shown in (Figure 5). Whenever, clock is negative, the output changes with
respect to data but remains constant as clock goes positive. The output remains unaffected and preserve its
previous state even if clock is absent, thus the proposed latch is static in nature. The input and supply voltage
range is taken as 0mv to 350 mV in steps of 50 mV.
The proposed latch is analyzed in terms of average power consumption (APC), delay and power delay product
(PDP) at varying supply voltages, frequencies and temperatures in sub-threshold region. PDP is the function of
power consumption as well as delay, so any reduction in average power consumption or delay will lead to
overall reduction in PDP. To establish an impartial testing environment both circuits were simulated on same
input patterns which covers each and every combination of the input stream. All these figures are plotted on
logarithmic scale to show better view of comparison. All simulation work is carried out at 65nm technology as
well as 45nm technology to show technology independency of the proposed circuit.

71

Vol 3, No 5, 2012

3.1. Simulation results in 65nm technology
It can be deduced from Figure 6 that with the increase in temperature power consumption also increases and
power consumption for both the designs are almost comparable. Power consumption is a dependent parameter
of supply voltage and as the supply voltage increases, power consumption also increases. Figure 7 presents the
same but APC of the proposed latch is slightly more than the conventional latch. Average power consumption is
also directly proportional to the input signal frequency. Figure 8 presents the comparison of the APCs of both
designs and APC of the 6T design is comparable upto 1 MHz but remarkably less at 5 MHz. Since the circuit
shows degraded performance above 5MHz and thus not simulated beyond 5 MHz.

As temperature increases, the characteristics of the semiconductor device are affected due to increase in
thermal generation and recombination rate of the carriers. Thus, average power consumption and delay of the
device are affected with temperature as the collision rate of the carrier increases and some of the power is
consumed in the form of thermal energy. It is clear from Figure 9 that the delay introduced by the proposed
design is lower than the 8T design.
Circuits operating in sub-threshold region are very sensitive to the supply voltage. The sensitivity of the circuit
delay increases with decreasing power supply value. Figure 10 indicates that delay in the proposed 6T design is
significantly less than the conventional 8T design at various supply voltages.
The dynamic power component of the power consumption, i.e., P = α.C.V2.f, where α is the switching activity,
is dominant at higher frequencies and becomes negligible at lower frequencies as the static power component

takes over, i.e., . Power consumption in sub-threshold region is much lower
than super-threshold region. Figure 11 shows the behavior of the proposed circuit with the variation in
frequency. As in sub-threshold region, circuits work better up to medium frequencies, hence range of frequency
is taken from 50 kHz to 5 MHz, and here also the 6T design shows better results than 8T.
The PDP is the amount of energy per switching activity of the signal. Thus, having a lower PDP means the
sub-threshold circuit is consuming less energy, when all the contending circuits are operating with the same
amount of switching activity. The product of Average power consumption and delay is calculated and
mentioned in the table 2- table 4. The analysis of the presented data reveals that the 6T design is better than the
8T design.

3.2. Simulation results in 45nm technology
Similar results are obtained when simulations are carried out at 45nm technology. It shows technology
independent behavior of the proposed circuit.
The average power consumption at various temperature, supply voltage and frequencies is plotted (Figure
12-14). In 45 nm technology, the average power consumption of the proposed design is found less than the
earlier design at all the values of the temperatures, voltages and frequencies. The produced results indicate that
the design is better suitable for low power designs.
Delay in the proposed design is always remarkably lesser than the previous 8T latch design (Figure 15-17) and
thus the PDP of the 6T latch is considerably reduced as indicated in the table 5- table 7.

72

Vol 3, No 5, 2012

4. Conclusion
In this paper, the design and the simulation results of the conventional and proposed design demonstrated and
found that the proposed 6-transistor latch is better in terms of power consumption and delay. Since the
transistor count is less, thus the proposed design is also area efficient. Hence the 6-transistor latch is better
viable option for the low power device designs.

References
[1] N. Weste and K. Eshraghian (1993), Principles of CMOS VLSI Design, A System
Perspective. Reading, MA: Addison- Wesley.
[2] Gary K.Yeap (1998), Practical Low power Digital VLSI Design, Kluwer Academic
Publishers.
[3] A. Wang, B. H. Calhoun and A. Chandrakasan (2005), Sub-threshold design for ultra
low-power systems, Springer publishers.
[4] Sagi Fisher, Adam Teman, Dmitry Vaysman, Alexander Gertsman, OrlyYadid-Pecht (2009),
Ultra-Low Power Sub-threshold Flip-Flop Design, ISCAS,IEEE international symposium
on Circuits and systems, pp.1573-1576.
[5] S. Kang and Y. Leblebici, CMOS Digital Integrated Circuits, Analysis and Design, 3rd ed.
[6] H. Soeleman, K. Roy, and B. Paul (2001), “Robust sub-threshold logic for ultra-low power
operation”, IEEE Trans. on Very Large Scale Integration (VLSI) Systems, vol. 9, no. 1, pp.
90–99.
[7] Meinerzhagen P., Sherazi S. M.Y., Burg A., Rodrigues J. N. (2011), “Benchmarking of
Standard-Cell Based Memories in the Sub-VT Domain in 65-nm CMOS Technology”, IEEE
Transactions on Emerging and Selected Topics in Circuits and Systems, vol. 1, no. 2.
[8] O. C. Akgun and Y. Leblebici (2008), “Energy efficiency comparison of asynchronous and
synchronous circuits operating in the sub-threshold regime”, J. Low Power Electron., vol. 4.
[9] Stojanovic, V. Oklobdzija,V. Bajwa (1998),
“Comparative analysis of latches and flip-flops for high performance systems”, Proc. of
International Conference on Computer Design: VLSI in Computers and Processors, pp.
264-269.
[10] Xiaoxuan She, N. Li, and W. Darresware Farwell (2010), “Tunable SEU-Tolerant Latch”,
IEEE transactions on Nuclear Science, vol. 57, no. 6, pp.3787-3794.

Ms. Abhilasha was born in Sikar, Rajasthan, India on 02/12/1988. She has done B.Tech in Electronics and
Communication Engineering from the Faculty of Engineering & Technology, Mody Institute of Technology and
Science, Rajasthan, INDIA in 2010. Presently, she is pursuing M.Tech. in VLSI Design from the same
university.
Mr. K. G. Sharma K.G. Sharma received the B.E. degree in Electronics and Communication Engineering from
Madan Mohan Malviya Engineering College, DDU University, Gorakhpur in 2001 and completed his M Tech.

73

Vol 3, No 5, 2012

degree in VLSI design from Faculty of Engineering & Technology, Mody Institute of Technology and Science
in 2009. Now he is pursuing his Ph.D. degree in the field of low power VLSI circuits from from Suresh Gyan
Vihar University, Jaipur. He demonstrated his skills in Research & Development of Industrial Electronics,
Kanpur for a briefer period and then he shifted to Academics and shared his knowledge as lecturer at renowned
university in Kanpur in the initial stages of his career. He extended his profession as faculty of Engineering and
Technology in MITS from 2003 and with experience promoted to Asst. Professor in the same university.
Because of his extensive research work, he has more than 30 research papers published in various international/
national journals and conferences. Mr. Sharma is the life member of Indian Society of Technical Education
(ISTE).
Mrs. Tripti Sharma She earned B.E. degree in Electronics Engineering from North Maharashtra University in
2001 and M Tech. degree in VLSI Design from Faculty of Engineering & Technology, Mody Institute of
Technology and Science, Rajasthan in 2010. Presently, she is pursuing Ph.D. in the field of low power high
performance digital VLSI circuit design from Suresh Gyan Vihar University, Jaipur. After stepping into
professional world, she started as lecturer with C.S.J.M University, Kanpur and continued it up to late 2003.
After that she joined Faculty of Engineering & Technology, Mody Institute of Technology and Science,
Rajasthan. Her working habits and discipline made her popular among the university and she was later awarded
with designation of Asst. Professor in 2009. Her current research interests include digital VLSI circuits. She has
over 20 papers published in International and national Journals and over 10 presentations in International and
National Seminars / Symposia/ Conferences. Mrs. Sharma is the life member of Indian Society of Technical
Education (ISTE).
Prof. B. P. Singh was born in a village Orro, Nawadah, Bihar, India in 1947. He did B.Sc. (Engg.) and M.Sc.
(Engg.) from Bihar Institute of Technology, Sindri, Dhanbad and B.I.T. Mesra Ranchi in 1967 and 1970. He did
Ph.D. from Ranchi University Ranchi in 1980. He served B.I.T. Mesra, Ranchi from 1970 to 1981, Indian
School of Mines Dhanbad from 1981 to 1987 and Madan Mohan Malaviya Engg. College from 1987 to 2009.
From 2009 till date he is the H.O.D. of ECE and EEE, Mody Instiute of Technology Lakshmangarh, Sikar,
Rajasthan (India). He has over 50 papers to his credits in International and national Journals and over 50
presentations in International and National Seminars / Symposia/ Conferences. His area of research is device
modeling, low-power and high performance integrated circuit design and emerging CMOS technologies. Prof.
Singh is the senior fellow of IEEE and life member of IETE.

Figures

74

Vol 3, No 5, 2012

Figure 1. Conventional 8 Transistor Latch

Figure 2. Proposed 6 Transistor Latch

75

Vol 3, No 5, 2012

Figure 3. Layout of existing 8T latch

76

Vol 3, No 5, 2012

Figure 4. Layout of proposed 6T latch

Figure 5. Input-Output waveform of the proposed 6T latch

77

Vol 3, No 5, 2012

Figure 6. APC at different temperatures

Figure 7. APC at various supply voltages

Figure 8. APC at different frequencies

78

Vol 3, No 5, 2012

Figure 9. Delay at different temperatures

Figure 10. Delay at various supply voltages

Figure 11. Delay at varying different frequencies

79

Vol 3, No 5, 2012

Figure 12. APC at various temperatures

Figure 13. APC at different supply voltages

Figure 14. APC at different frequencies

80

Vol 3, No 5, 2012

Figure 15. Delay at different temperatures

Figure 16. Delay at various supply voltages

Figure 17. Delay at different frequencies
Tables

81

Vol 3, No 5, 2012

Table 1. Parasitic Capacitance of existing and proposed latch
Parasitic Capacitance (F)
Latch
Output capacitance Total capacitance
8T 1.80E-016 7.06E-16
6T 1.29E-016 5.47E-16

Table 2. PDP with increasing temperatures
Temperature(oC) 8T 6T
-5 1.14E-19 1.36E-19
5 1.29E-19 1.22E-19
15 1.49E-19 1.41E-19
25 1.73E-19 1.66E-19
35 1.98E-19 1.90E-19
45 2.22E-19 2.10E-19
55 2.42E-19 2.20E-19
65 2.57E-19 2.12E-19
75 2.78E-19 2.28E-19

Table 3. PDP with varying input voltage and supply voltages
Voltage (volt) 8T 6T
0.30 9.75E-20 4.80E-20
0.31 1.14E-19 7.30E-20
0.32 1.28E-19 9.93E-20
0.33 1.45E-19 1.19E-19
0.34 1.60E-19 1.54E-19
0.35 1.73E-19 1.66E-19

Table 4. PDP with increasing operating frequencies
Frequency 8T 6T
50kHz 1.24E-19 1.16E-19
100kHz 1.27E-19 1.20E-19
500kHz 1.49E-19 1.29E-19
1MHz 1.73E-19 1.66E-19
5MHz 3.88E-19 2.53E-19

82

Vol 3, No 5, 2012

Table 5. PDP with increasing temperatures
Temperature(oC) 8T 6T
-5 3.59E-20 2.45E-21
5 3.44E-20 4.76E-21
15 3.11E-20 4.76E-21
25 3.91E-20 7.20E-21
35 4.95E-20 1.16E-20
45 6.04E-20 1.77E-20
55 7.71E-20 2.60E-20
65 1.03E-19 3.42E-20
75 1.40E-19 3.84E-20

Table 6. PDP with varying input voltage and supply voltages.
Voltage (volt) 8T 6T
0.18 3.04E-20 1.36E-20
0.19 3.38E-20 1.16E-20
0.20 3.91E-20 9.99E-21
0.21 4.47E-20 7.47E-21
0.22 4.70E-20 4.59E-21

Table 7. PDP with increasing operating frequencies
Frequency 8T 6T
50kHz 1.99E-20 6.57E-21
100kHz 2.11E-20 6.74E-21
500kHz 2.93E-20 9.08E-21
1MHz 3.91E-20 1.16E-20
5MHz 1.17E-19 1.30E-20

83

Low power 6 transistor latch design for portable devices

More Related Content

What's hot (18)

Viewers also liked (6)

Similar to Low power 6 transistor latch design for portable devices (20)

More from Alexander Decker (20)

Recently uploaded (20)

Low power 6 transistor latch design for portable devices