Bandwidth Enhancement of Rectangular Patch Microstrip Antenna with parallel rectangular slots for WLAN Applications

Chandan Kumar Dubey et al. Int. Journal of Engineering Research and Applications www.ijera.com
ISSN : 2248-9622, Vol. 5, Issue 3, ( Part - 3) March 2015, pp.74-78
www.ijera.com 74|P a g e
Bandwidth Enhancement of Rectangular Patch Microstrip
Antenna with parallel rectangular slots for WLAN Applications
¹Chandan Kumar Dubey, ²Rakesh Kumar, ³Pramod Kumar
*(Assistant Professor, Department of Electronics & Communication Engineering, Poornima Group of
Institutions, Jaipur, India)
** (B.Tech., VIII Sem., Department of Electronics and Communication Engineering, Poornima Group of
*** (B.Tech., VIII Sem., Department of Electronics and Communication Engineering, Poornima Group of
ABSTRACT
Many applications require very broadband antenna, but the narrow bandwidth of a microstrip antenna restricts
its wide usage. The aim of this paper is to enhance the bandwidth of rectangular microstrip patch antenna. For
this purpose, we cut three rectangular parallel slots in the proposed antenna. The dielectric substrate material of
the antenna is glass epoxy FR4 having εr=4. 4 and loss tangent 0.025. The performance of the final modified
antenna is compared with that of a conventional rectangular microstrip antenna. The designed antenna has two
resonant frequencies 4.49 GHz and 4.90 GHz. So this antenna is best suitable for the WLAN applications and
IMT-band frequency operations. The designed antenna offers much improved impedance bandwidth 19.7%.
This is approximately six times higher than that in a conventional rectangular patch antenna (Bandwidth= 3%)
having the same dimensions.
Keywords– Broadband, FR4 substrate, Parallel slots, Gain, Resonant frequency
I. INTRODUCTION
In the recent years, there has been rapid growth
in wireless communication. Day by day users are
increasing, but limited bandwidth is available and
operators are trying hard to optimize their network for
larger capacity and improved quality coverage. This
surge has led the field of antenna engineering to
accomadte the need for broadband, low cost
miniaturized and easily integrated antennas[1]. A
widely used antenna structure with above
characteristics is microstrip patch antenna.
Microstrip patch antennas consist of a very thin
metallic strip (patch) on a grounded substrate found
extensive applications in wireless communication
systems owing to their advantages such as low
profile, conformability, low fabrication cost and ease
of integration with feed network. Microstrip patch
antennas come with a drawback of narrow bandwidth,
but wireless communication applications require
broad bandwidth and relatively high gain [2-3]. The
shape of antenna varies according to their use, the
work is continuously getting occurred to achieve
faithful factors, by small size antenna for broadband
communication [4-6]. Several techniques have been
used to enhance the bandwidth by interpolating
surface modification in patch configuration [7].
In past decades of communication world , microstrip
antennas have played an active role and have become
a major research topic due to their advantages and
ease in fabrication and integration with solid state
devices [8-9]. To increase the bandwidth of the
proposed microstrip patch antenna three rectangular
parallel slots have been introduced in the antenna
geometry. Dimension of slot is 2mm x 20 mm.
II. ANTENNA DESIGN
We considered a single layer conventional
microstrip patch antenna. Dimension for this
conventional patch were taken as Length L=28 mm
and Width W= 34 mm. FR4 substrate is used to
design this conventional patch by us. The dielectric
constant of FR4 is 4.4, loss tangent is 0.025 and The
thicknessof FR4 substrate is 1.6mm. The coaxial
probe feed technique was used to excite the patch.
Design and simulation process were carried out using
IE3D simulation software 2007 version 12.30.
The geometry of the conventional rectangular
microstrip patch antenna is depicted in figure 1.
Figure 1: Geometry of Conventional Rectangular
Patch Microstrip Antenna
RESEARCH ARTICLE OPEN ACCESS

III. RESULTS
The conventional rectangular patch antenna is
simulated first using IE3D software. This simulated
reflection coefficient curve shows that our
conventional rectangular patch antenna is resonating
at frequency 4.89 GHz as shown in figure 2. The
value of impedance bandwidth of conventional
rectangular microstrip patch antenna is 3%. The
simulated input impedance of the antenna at
resonance frequency 4.89 GHz is (50.84- j 5.14) ohm
which is close to 50 ohm impedance. Since the
rectangular patch antenna has low bandwidth, so to
improve the performance of this antenna further
modifications are required.
Figure 2: Variation of Reflection Coefficient v/s
Resonant Frequencies
Figure 3: Structure of Rectangular Patch Microstrip
Antenna with two parallel rectangular slots
So in order to increase the bandwidth we cut two
rectangular parallel slots in antenna geometry as
depicted in figure 3. The size of slots is 2 mm x 20
mm. The gap between these two parallel slots is 20
mm. The figure 4 shows the variation of reflection
coefficient with frequency. It shows that the modified
antenna is resonating at 4.90 GHz frequency. After
modification in the conventional rectangular patch ,
this time we got the value of impedance bandwidth is
5%. The simulated result shows that the input
impedance at resonant frequency 4.90 GHz is (48.50
– j4.7) ohm which is very close to 50 ohm.
Resonance Frequency of RSMPA.
Still, we have not received a precise bandwidth. In
our next step of designing process, we cut one more
rectangular slot in the middle area of our proposed
antenna geometry to get wider bandwidth. The
structure of final modified rectangular patch
microstrip antenna is shown in figure 5.
Figure 5: Structure of final modified rectangular
patch microstrip antenna
The figure 6 shows the variation of reflection
coefficient with resonant frequencies. It shows that
after second modification the antenna is resonating at
two resonant frequencies 4.49 GHz and 4.90 GHz. In
this case we achieved the bandwidth of 19.7%
corresponding to the frequencies 4.49 and 4.90 GHz.

Resonance Frequencies
The smith chart for this modified antenna is shown in
the figure 7. At the resonant frequencies 4.49 GHz,
and 4.90 GHz the measured input impedances are
(51.93 + j 6.55) ohm and (52.54 – j 0.33) ohm
respectively.
Figure 7: Smith chart of final modified rectangular
patch microstrip antenna
The gain curve for this antenna is shown in figure 8.
The simulated gain at frequencies 4.49 GHz and 4.90
GHz are -0.85 dBi and 1.90 dBi respectively. So
finally we got broadband antenna.
Figure 8: Variation of gain v/s resonance frequencies
The curve between directivity and resonant
frequencies is shown in fig. 9. The directivity of this
antenna is 8.20 dBi and 7.99 dBi for the resonant
frequencies 4.49 GHz and 4.90 GHz respectively.
Figure 9: curve between directivity and resonant
frequencies
The curve between radiation efficiency and resonant
frequencies is shown in figure 10.

Figure 10: curve between radiation efficiency and
resonant frequencies
The radiation efficiency of the antenna is 12.49 % at
4.49 GHz and 24.75 % at 4.90 GHz. The variation of
VSWR with the resonance frequencies is shown in
figure 11. The values of VSWR at resonance
frequencies 4.49 GHz and 4.90 GHz are 1.17 and
1.07 respectively.
Figure 11: curve between VSWR and resonant
frequencies
The radiation patterns at resonant frequencies 4.49
GHz and 4.90 GHz are shown in figure 12 and figure
13 respectively. At 4.49 GHz the direction of
maximum radiation is normal to the patch geometry.
At 4.9 GHz the direction of maximum radiation is
shifted 60o
left and 60o
right side of the normal to the
patch as represented in the following figures.
Figure 12: 2D polar Radiation pattern at 4.49 GHz
Figure 13: 2D polar Radiation pattern at 4.9 GHz
IV. CONCLUSION
The proposed Ractangular patch microstrip
antenna with parallel rectangular slots resonates at
two frequencies 4.49 GHz and 4.9 GHz. By using
this antenna we got much improved bandwidth of
19.7 % in comparison with a conventional rectangular
patch antenna having a bandwidth of 3%. The
designed antenna exhibits a good impedance
matching of about 50 ohm. From the analysis of
simulated results it can be verified that the proposed
antenna is best suitable for WLAN applications. This
antenna is also useful for IMT- band frequency
operations.
IV. ACKNOWLEDGMENT
The authors would like to express their
gratitude towards Dr. Rakesh Duggal, Director,

Poornima Group of Institutions, Jaipur for his
kind cooperation in this research work.
REFERENCES
[1] D. Sanchez- Hernandez and I.D. Robortson,
“ A survey of broadband microstrip patch
antenna” Microwave Journal, pp. 60-84,
September 1996.
[2] Churng-Jou Tsai, Chia-Hsn Lin, Wei-Chih
Chen, Chen-Lin Lu and Jinn-KweiGuo, “A
CPW-Feed Printed Antenna for Dual-band
WLAN operations”, IEEE, 2011.
[3] I. Balakrishna, M. Suresh kumar and S.
Raghavan, “CPW-fed Semi Circle Patch
Antenna for 2.4 GHz WLAN Application”,
IEEE, 2011.
[4] K. guney, “A simple and accurate expression
for the bandwidth of electrically thick
rectangular microstrip antennas”, Microwave
and Optical Technology Letters, Vol.36, No.3,
pp. 225-228,2003Vol. 1 No. 1-2 (January-
December, 2012)
[5] Er. O.p. Rajpoot, Dr. D. C. dhubkarya,
“Design and Analysis of Rhombus Shaped
Microstrip Antenna”, Int. Jr. of Knowledge
Engineering and Technology, Vol. 1 No. 1-2
(January-December, 2012)
[6] DheerajBhardwaj, Deepak Verma, Komal
Sharma, “ Design of Dual Band Broadband
Modified RectangularMicrostrip Antenna with
air gap for Wireless Applications,
”International Journal of Enhanced Research
in Science, Technology& Engineering, ISNN:
2319-7463, Vol.3 Issue 2, February-2014, pp:
(331-339)
[7] DheerajBhardwaj, Komal Sharma “Broadband
rectangular patch microstrip antenna with
rhombus shaped slot for WLAN applications”,
International Journal of Enhanced Research in
Science, Technology& Engineering, ISNN:
2319-7463, Vol. 3 Issue 1, January-2014, pp:
(389-394)
[8] Er.O.P.Rajpoot , Dr. D. C. Dhubkarya,
“Design and Analysis of Rhombus Shaped
Microstrip Antenna”, Int. Jr. of Knowledge
Engineering and Technology, Vol. 1 No. 1-2
(January-December, 2012)
[9] Ch.Radhika,1D.Ujwala, B.Harish,
Ch.VijayaSekhar, H.M.Ramesh,”Analysis of
the effect of substrate thickness on a rhombus
shaped slot triangular Patch Antenna for
WLAN application”,International Journal of
Engineering Research and Applications
(IJERA) ISSN: 2248-9622 www.ijera.com Vol.
2, Issue3, May-Jun 2012, pp.2503-2506

Bandwidth Enhancement of Rectangular Patch Microstrip Antenna with parallel rectangular slots for WLAN Applications

More Related Content

What's hot

Viewers also liked

Similar to Bandwidth Enhancement of Rectangular Patch Microstrip Antenna with parallel rectangular slots for WLAN Applications

Recently uploaded

Bandwidth Enhancement of Rectangular Patch Microstrip Antenna with parallel rectangular slots for WLAN Applications