ON IEEE 802.11: WIRELESS LAN TECHNOLOGY

International Journal of Mobile Network Communications & Telematics ( IJMNCT) Vol. 3, No.4, August 2013
DOI : 10.5121/ijmnct.2013.3405 45
ON IEEE 802.11: WIRELESS LAN TECHNOLOGY
Sourangsu Banerji1
and Rahul Singha Chowdhury2
1
Department of Electronics & Communication Engineering, RCC-Institute of Information
Technology, Kolkata, India
sourangsu.banerji@gmail.com
2
Department of Electronics & Communication Engineering, RCC-Institute of Information
Technology, Kolkata, India
rahul.singhachowdhury@gmail.com
ABSTRACT
Network technologies are traditionally based on wireline solutions. But the introduction of the IEEE 802.11
standards have made a huge impact on the market such that laptops, PCs, printers, cellphones, and VoIP
phones, MP3 players in our homes, in offices and even in public areas have incorporated the wireless LAN
technology. Wireless broadband technologies nowadays provide unlimited broadband access to users
which were previously offered only to wireline users. In this paper, we review and summarize one of the
emerging wireless broadband technology i.e. IEEE 802.11,which is a set of physical layer standard for
implementing wireless local area network computer communication in the 2.4,3.6,5 and 60GHz frequency
band. They fix technology issues or add functionality which is expected to be required by future
applications. Though some of the earlier versions of these technologies are obsolete (such as HiperLAN)
now but still we have included them in this review for the sake of completeness.
KEYWORDS
Wireless Communications, IEEE 802.11, HiperLAN, WLAN, Wi-fi.
1. INTRODUCTION
The wireless broadband technologies were developed with the aim of providing services
comparable to those provided to the wireline networks. Cellular networks now provide support
for high bandwidth data transfer for numerous mobile users simultaneously. In addition to this,
they also provide mobility support for voice communication. Wireless data networks can be
divided into several types depending on their area of coverage. They are:
WLAN: Wireless Local Area network, in area with a cell radius up to hundred meters, mainly in
home and office environments.
WMAN: Wireless Metropolitan Area Network; generally cover wider areas as large as entire city.
WWAN: Wireless Wide Area Network with a cell radius about 50 km, cover areas larger than a
city.
However out of all of these standards, WLAN and recent developments in WLAN technology
would be our main area of study in this paper. The IEEE 802.11 is the most widely deployed
WLAN technology as of today. Another well known is the HiperLAN standard by ETSI. Both
these technologies are united under the Wireless Fidelity (Wi-fi) alliance. In literature though,
IEEE802.11 and Wi-fi is used interchangeably and we will also follow the same convention in
this paper. A typical WLAN network consists of an Access Point (AP) in the middle/centre and a
number of stations (STAs) are connected to this central Access Point (AP).Now, there are
basically two modes in which communication can take place.

46
In the centralized mode of communication, communication to/from a STA is always carried over
the APs. There is also a decentralized mode in which communication between two STAs can take
place directly without the requirement of an AP in an ad hoc fashion. WLAN networks provide
coverage up to an area of 50-100 meters. Initially, Wi-fi provided an aggregate throughput of
11Mbps, but recent developments have increased the throughput to about 54 Mbps. As a result of
its high market penetration, several amendments to the basic IEEE 802 standard have been
developed or are currently under development.
In this paper, we overview the IEEE 802.11 standard and address the technical context of its
extensions. In section 2, we briefly discuss the history behind the development of the standard.
Section 3 deals with the features of the IEEE 802 family which have already been implemented.
In the following section 4, we look at other standards besides IEEE 802.11a; IEEE 802.11b/g. In
section 5, some of the upcoming standards are discussed and some open issues with the IEEE
802.11 standard is given in section 6. The HiperLAN and its standards have been talked about in
section 7 and 8. In Section 9 we state the reasons of HiperLANs’ failure over IEEE 802.11. Lastly
we conclude our paper in section 10.
2. DEVELOPMENT OF IEEE 802.11
The Physical layer (PHY) and medium access control (MAC) layer were mainly targeted by the
IEEE 802 project. When the idea of wireless local area network (WLAN) was first conceived, it
was just thought of another PHY of one of the available standards. The first candidate which was
considered for this was IEEE’s most prominent standard 802.3.
However later findings showed that the radio medium behaved quite different than the
conventional well behaved wire. As there was attenuation even over short distances, collisions
could not be detected. Hence, 802.3’s carrier sense multiple access with collision detection
(CSMA/CD) could not be applied.
The next candidate standard considered was 802.4. At that point of time, its coordinated medium
access i.e. the token bus concept was believed to be superior to 802.3’s contention-based scheme.
Hence, WLAN began as 802.4L. Later in 1990 it became obvious that token handling in radio
networks was rather difficult. The standardization body realized the need of a wireless
communication standard that would have its own very unique MAC. Finally, on March 21, 1991,
the project 802.11 was approved (fig. 1).
Figure 1 WLAN Network Architecture
3. IEEE 802.11 FAMILY
The most widely deployed 802.11 standard has a lot of extension and many more are currently
under development. First introduced in 1999, the IEEE 802.11 standard was primarily developed
keeping in mind the home and the office environment for wireless local area connectivity. The

47
initial standards gave a maximum data rate of 2Mbps per AP which increased to 11 Mbps per AP
with the deployment of IEEE 802.11b [2].Newer extensions like IEEE 802.11g and IEEE 802.11a
provided maximum data rate of 54Mbps per AP using various methods to boost up the maximum
data rates [3-5]. WLAN devices based on IEEE 802.11g currently offer data rate 100-125Mbps
[4].
Similarly, a relatively newer IEEE 802.11n gives a maximum data rate of about 540Mbps
[25].Furthermore, in addition to these, several other standards were deployed which solved many
QoS and security issues related with the earlier standards. Additional mechanisms were
introduced to remedy QoS support and security problems in IEEE 802.11e [12] and IEEE
802.11i.The IEEE 802.11n standard which we earlier talked about also introduced MAC
enhancements to overcome MAC layer limitations in the current standards [28]. The IEEE
802.11s standard added mesh topology support to the IEEE 802.11 [34]. The IEEE 802.11u
improved internetworking with external non-802.11 networks. The IEEE 802.11w was added
onto 802.11i covering management frame security.
The IEEE 802.11ad standard adds a "fast session transfer" feature, enabling the wireless devices
to seamlessly make transition between the legacy 2.4 GHz and 5 GHz bands and the 60 GHz
frequency band [41]. The IEEE 802.11ac standard, still under development is expected to provide
a multi-station WLAN throughput of at least 1 Gbps and a single link throughput of at least 500
Mbps [45].
3.1. Physical (PHY) Layer
The IEEE 802.11 uses variety of PHY layers with the aim of increasing the aggregate throughput
of the network. IEEE 802.11 standard includes three PHY layers namely:
1. FHSS (Frequency Hopping Spread Spectrum)
2. DSSS (Direct Sequence Spread Spectrum)
3. IR (Infrared)
In addition to these 802.11b uses a new PHY layer, High Rate DSSS [1].IEEE 802.11a and
802.11g are based on OFDM (Orthogonal Frequency Division Multiplexing); that greatly
increases the overall throughput of the AP [2-4]. Various OFDM modulation techniques are
summarized in Table 1. 802.11n also uses OFDM modulation technique but coupled with a
MIMO (Multi Input Multi Output) mechanism [28].The frequency band of operation of most of
the extensions of IEEE 802.11 is 2.4 GHz with 14 distinct channels. The availability of these
channels varies from one country to another. Out of these the last channel was especially designed
for Japan which was the main feature incorporated in IEEE 802.11j extension.
Table 1
OFDM PHY layer modulation techniques
Data Rate
(Mbps)
Modulation Coding rate Coded bits/sub
carrier
Code
bits/OFDM
symbol
Data
bits/OF
DM
symbol
6 BPSK 1/2 1 48 24
9 BPSK 3/4 1 48 36
12 QPSK 1/2 2 96 48
18 QPSK 3/4 2 96 72
24 16-QAM 1/2 4 192 96
36 16-QAM 3/4 4 192 144
48 64-QAM 2/3 6 288 192
54 64-QAM 3/4 6 288 216

48
The IEEE 802.11a extension employs a number of channels ranging from 36-161 depending on
the frequency band (5.15-5.825 GHz) although it works with a fixed channel centre frequency of
5 GHz. There are 12 non overlapping channels in the frequency band for the IEEE standard in the
U.S. and 19 non-overlapping channels in Europe [3]. In contrast, there are only 3 out 14 non-
overlapping channels in case of 802.11b [2]. IEEE 802.11n uses overlapping channels with
channel bandwidth of 20 and 40MHz [19]. The 20MHz channel bandwidth is incorporated in
every 802.11n device, the 40MHz channel being optional.
Peer to Peer (P2P) WLAN links can be established with the help of directional antennas for a few
km ranges. A typical WLAN Access Point (AP) uses omnidirectional antennas with a range of
30-50m (indoors) and 100m (outdoors).This range is greatly affected by the obstacles between the
AP and the STA.IEEE 802.11a suffer from increased range and attenuation compared to IEEE
802.11b/g networks because it operates on the higher frequency range of 5MHz.Use of sectored
antennas instead of omnidirectional antennas increases the aggregate WLAN data rate in a given
area to 2-3 times [6].
3.2. Medium Access Control (MAC) Layer
IEEE 802.11 uses a contention based scheme known as Distributed Coordinated Function (DCF).
In this method the STA linked with the AP scans the air interface for channel availability. If the
interface is idle, the STA sends it data to the destination through the AP. If however the air
interface is busy or more than one STA tries to access the same AP; a collision occurs. The IEEE
802.11 uses a Carrier Sense Multiple Access/Collision Avoidance (CSMA/CA) to avoid the
collisions. IEEE 802.11 uses another MAC technique known as Point Coordination Function
(PCF) [18]. This mechanism is divided in to two parts. In the first part, the AP scans all its STA
in a round robin fashion and checks to see if any of the STAs has any packets to send. If any of
the STAs is not polled during the current period, it will be queued up for polling during the next
polling period. The scanned part uses the contention based scheme and is same as DCF.
Moreover, due to polling mechanism in PCF the aggregate throughput of an IEEE 802.11 network
decreases. DCF is the default MAC technique used in the IEEE 802.11 standard. While the
standard includes both the MAC techniques, PCF is included in the Wi-fi alliance standard and
hence not quite as popular as DCF [17]. In both the MAC techniques an automatic response
request mechanism is used in this method. Any device in the network receiving data will send an
acknowledgement signal (ACK) back to the sender. In case the receiver receives a corrupt data
packet, it issues a NAK (Negative Acknowledgement) and the sender resends the data packet.
There is a round trip delay as the sender has to wait for the ACK to transmit the next data packet
in the queue.
3.3. Request to Send/Clear to Send (RTS/CTS)
In the contention based scheme called DCF if more than two STAs simultaneously try to access
the air interface, a collision occurs. To avoid such collision CSMA/CA may result in incorrect
medium information. This is called Hidden Node Problem in which collision in the some part of
the network cannot be detected [15]. If any two STAs cannot directly communicate, the AP
invokes a RTS/CTS mechanism. For each transmission, the source STA issues a RTS message.
The destination STA replies to this by sending a CTS message. Upon receiving the CTS message,
the source STA starts its data transmission. The medium is assumed to be in use given in the
message when they receive RTS and/or CTS message. In PCF using RTS/CTS reduces the
network throughput.
3.4. Authentication & Encryption
Security is also handled in the MAC layer. To avoid unauthorized access from other STAs,
several encryption methods have been used. One of earlier encryption mechanism was Wired

49
Equivalent Piracy (WEP). But the encryption method had security vulnerabilities and the Wi-fi
Alliance developed another encryption technique named Wi-Fi protection Access (WPA).
The IEEE 802.11i standard incorporated an enhanced version of WPA (WPA2) [20]. IEEE
802.11i also addressed security issues associated with authentication methods like open standard
and shared key authentication and incorporated IEEE 802.1X authentication method which is now
used in all the later versions of IEEE 802 family standards. In this method, users can authenticate
their identities by a RADIUS or diameter server.
3.4.1. Management Frame
The current 802.11 standards define "frame" types for use in management and control of wireless
links. The TGw implemented the IEEE 802.11w standard to implement the Protected
Management Frames. The TGw is still working on improving the IEEE 802.11 MAC layer.
Security can be enhanced by providing data confidentiality of management frames. These
extensions will have interactions with IEEE 802.11r as well as IEEE 802.11u
3.5. OPERATING MODES
The IEEE 802.11 supports two operating modes. They are namely:
1. Infrastructure operating mode and
2. Independent operating mode.
In the infrastructure operating mode, the STAs communicate with each other through the Access
Point. In this scheme, an STA needs to be connected to an Access Point in the network in order to
talk to another STA (fig.2).
Figure 2 Infrastructure Mode
However, in the independent mode or ad hoc mode, the STAs can directly communicate with
each other. In this mode, the source STA forms an ad hoc link directly with the destination STA
(fig.3).
Figure 3 Independent Mode

50
3.6. QUALITY OF SERVICE (QOS)
In 2005, IEEE developed a new extension of 802 standards known as 802.11e to standardize QoS
enhancement efforts. This was done to tackle the QoS provisioning problem induced by the MAC
techniques like PCF and DCF in the earlier extensions. The MAC techniques in the IEEE 802.11e
significantly enhance QoS support for Wi-fi. Two new MAC techniques were introduced in
802.11e. These were HCF and EDCF. The HCF method was based on PCF and EDCF was based
on DCF. In addition to these, two more MAC enhancements were also introduced to increase the
MAC layer throughput. One of them was Block Acknowledgement which enabled sending of a
single ACK for a block of frames. Another one was Direct Link Protocol, which enabled direct
link between two STAs in a single WLAN network.
3.6.1. Hybrid Coordination Function (HCF)
The principle MAC technique in IEEE 802.11e extension, Hybrid Coordination Function is based
on PCF mechanism used in the earlier standards. However unlike PCF, HCF is mandatory for
devices that support 802.11e.The contention free period in HCF is known as HCF controlled
Channel Access (HCCA).
In HCF, there are several EDCA periods for random access. The main difference between PCF
and HCF is that in HCF unlike PCF, the packets with different QoS are mapped into different
MAC queues, with different polling priorities assigned to each one. They are known as Traffic
Classes (TC). The QoS enhanced Access Point (QAP) polls the TCs of the STAs using a priority
based round robin schedule starting with the first QSTAs having the highest TC queue.
3.6.2. Enhanced Distributed Channel Access (EDCA)
EDCA is only used as a supplementary part with the first technique, HCF. It is quite similar to
DCF. It is also similar in operation to HCCA as packets are queued up in different Access
Categories (ACs) in EDCA similar to the TCs. In EDCA, different QSTAs act as a virtual STA
for different QoS levels. The medium access parameters of ACs of a given STA depend on their
respective priorities. ACs are however different from TCs; as a given type of packet always has
one AC and one TC in a wi-fi network.
3.6.3. Block Acknowledgement
The block acknowledgement mechanism was also introduced in 802.11e standard for QoS
enhancement. Traditionally, an ACK was sent for every MAC frame received by the destination
STA. But ACKs caused high overhead and waiting time delay. To overcome this, IEEE 802.11e
used frame blocks and sent one ACK for every block. Even though it speeds up the process but
the primary disadvantage of retransmitting the entire block again on failure to receive an ACK
signal still persists.
3.6.4. Direct Link Protocol (DLP)
Two STAs in the same WLAN can only communicate through an AP. So the amount of
bandwidth consumed is twice the actual rate of transmission. DLP is a technique which allows
two STAs to directly communicate with each other without using an Access Point, avoiding
excess of bandwidth.
The MAC techniques in IEEE 802.11e divide the transfer time into Transmission Opportunities
(TO) [10]. A QSTA can use the medium for a number of TOs. This eliminates the timing problem
in PCF. In both the EDCA and HCF techniques, at the onset of transmission, the QSTA sends an
information packet with QoS specifications for communication request. Now if a QAP can handle
the transmission subject to all the QoS parameters passed to it, it accepts it otherwise it rejects the
request, which can again be retried with a relatively lower QoS parameter.
Additional mechanisms to further improve MAC throughput and QoS support have been
proposed. In the paper [13] it has been shown that using an adaptive contention window, Inter

51
Frame Space (IFS) parameters which are based on the link condition improve the overall
performance of IEEE 802.11e amendment. In [12] it was proposed that the polling mechanism
could be replaced with a request based scheduler. In this case, each of the QSTA sends a request
for their queues to the QAP. The QSTA schedules these uplink packets with its own downlink
packets using a modified Weighted Fair Queuing Scheme.
3.7. Contention Based Protocol (CBP)
First introduced in IEEE 802.11y the contention based protocol is a communication protocol for
wireless communication equipment that allow user to use the same radio channel without pre-
coordination. One of the well known contention based protocol of the IEEE 802.11 standard is
“listen before talk”.
The protocol allows multiple users to use the same radio frequency spectrum by establishing rules
in which a transmitter provides reasonable opportunities to other transmitters when both of them
simultaneously try to access the same channel. It consists of separate procedures for initiating
new transmissions, determining the state of the channel and for managing retransmissions in the
event of a busy channel.
3.8. Extended Channel Switch Announcement (ECSA)
If the necessity arises to change the current operating channel or the channel bandwidth, the IEEE
802.11y provided a mechanism for an AP to notify the stations connected to it of its intentions.
This will provide an opportunity to the WLAN to choose a channel which is less noisy and the
least likely to cause any interference. In addition, ECSA also provides other functionalities
besides dynamic channel selection like for instance, the licensed operator can send ECSA
commands to any stations operating under their control, either registered or unregistered [39]. The
IEEE 802.11n also used ECSA which provided for the 20MHz and 40MHz channel switching in
the 11n PHY’s ECSA. However, IEEE 802.11n is specified for operation in the 2.4GHz and
5GHz license exempt bands. But after IEEE 802.11y, future amendments could permit 11n's PHY
to operate in other bands as well, which is seen in the upcoming IEEE 802.11ad standard
3.9. Dependent Station Enablement (DSE)
Another important concept introduced in the IEEE 802.11y is the mechanism by which an
operator extends and retracts permission for license exempt devices to use the licensed radio
spectrum. In addition, the DSE provides benefits like enabling a dependent STA to connect to its
nearest AP for a short period of time and use the internet to complete the channel permission
process with the enabling station. This facility reduces the likelihood of a dependent STA to cause
interference while attempting to connect to a far off enabling station.
The personal privacy and security of end users are ensured while, at the same time, licensees will
have the information necessary to resolve disputes. This is achieved as the devices based on IEEE
802.11y transmit a unique identifier to resolve the interference dispute. The enabling stations also
transmit their unique identifier indicating their location. The FCC database will also contain the
location of the enabling station that will identify the licensee. The dependent STAs provide the
location of the station that enabled it plus a unique string supplied by the enabling station. This
ensures that to resolve disputes the responsible party, the licensee, can be contacted. This method
alleviates the problems associated with having the dependent STA broadcasting its location.
However this method would increase the cost and complexity of devices. Moreover, this
technique also suffers from the uncertainty that mobile devices those constantly beacon its
location could be adversely used by third parties to track the user’s location
3.10. Mobility
The IEEE 802.11 standard was developed as an alternative to wireline cellular networks. The
mobile user profiles were originally not defined in the IEEE 802.11 standard [18]. IEEE 802.11e

52
addressed the issue of intra AP communication but the standard still does not provide any solution
for roaming users [13]. However, the cellular IP Architecture provides a solution for seamless
transition between different LAN networks [24]. Here, several WLANs are connected to the
internet and are interconnected among them using a gateway, which keeps records of all the
moving paths.
4. OTHER STANDARDS
4.1. IEEE 802.11c
The IEEE 802.11c standard covers bridge operation. Formally, a bridge is a device which links to
LANs with a similar or identical MAC protocol. A bridge performs functions which are similar to
those of an Internet Protocol (IP)-level router, but at the MAC layer. A bridge is simpler and
efficient than an IP router.
In 2003, the 802.11c task group completed its work on this standard, which later on folded into
the IEEE 802.1d standard for LAN bridges. IEEE 802.11c acted as a supplement to IEEE 802.1d
which added requirements associated with bridging 802.11 wireless client devices. It adds a sub
clause under 2.5 Support of the Internal Sublayer Service, to cover bridge operations with 802.11
MACs. As of now, this standard is a part of IEEE 802.1d.
4.2. IEEE 802.11d
Deployed in 2001, IEEE 802.11d is an amendment to the IEEE 802.11 specification that added
support for "additional regulatory domains"[8]. Issues related to regulatory differences in various
countries are covered and also defined operation parameters at the 5MHz frequency band, but that
only for North America, Europe and Japan. This support also included the addition of a country
information element to beacons, probe requests as well as to probe responses. This country
information element greatly simplified creation of 802.11 wireless APs and client devices that
meet the different regulations enforced in various parts of the world to which they must conform
to operate at the 5MHz.
4.3. IEEE 802.11e
IEEE 802.11e was deployed in 2005 and is an important amendment to the IEEE 802.11 standard
that provided a set of Quality of Service enhancements for wireless LAN applications through
modifications to the Media Access Control (MAC) layer [10].
As discussed earlier, IEEE 802.11e accommodated time-scheduled and polled communication
during null periods when no other data is moving through the system [9]. In addition, IEEE
802.11e improves the polling efficiency and channel robustness. These enhancements should
provide the quality which is necessary for services such as IP telephony and video streaming [12-
14]. In a QSTA, a hybrid coordination function (HCF) replaces modules for a distributed
coordination function (DCF) and point coordination function (PCF). The HCF consists of
enhanced distributed-channel access (EDCA) [11] and HCF-controlled channel access (HCCA).
EDCA extends the existing DCF mechanism to include priorities. As with the PCF, HCCA
centrally manages medium access.
4.4. IEEE 802.11f
To provide for wireless access point communications among multivendor systems, the IEEE
802.11f or Inter-Access Point Protocol was a recommendation that described an optional
extension to IEEE 802.11. In addition to providing communication among WLAN stations in its
area, an AP can also function as a bridge that connects any two 802.11 LANs across another type
of a network, such as an Ethernet, LAN or a WMAN. Thus, IEEE 802.11f facilitated the roaming
of a device from one AP to another while ensuring transmission continuity. IEEE 802.11f

53
standard was a Trial Use Recommended Practice and so the standard was later withdrawn by the
IEEE 802 executive committee in 2006.
4.5. IEEE 802.11h
The European Union Military uses part of the 5 GHz frequency band for satellite and radar
communication in addition to the IEEE 802.11a signals. So to handle such situations, IEEE
802.11h introduced two mechanisms. These were:
1. Dynamic Frequency Selection (DFS)
2. Transmit Power Control (TPC)
In the DFS scheme, the AP detects other networks operating in the same frequency band and
changes the operating frequency of the WLAN to prevent collision. On the hand, TPC is used to
keep the signal level below a certain preset level if there is a satellite signal in the nearby
channels. Moreover, TPC can also be used to improve the link condition by switching over the
working frequency to a more suitable channel which is clearer and also reduce power
consumption [19].
4.6. IEEE 802.11i
The aim of the IEEE 802.11i standard was to address security issues. The security and
authentication mechanisms at the MAC layer were defined in this standard. It addressed the
security deﬁciencies in the Wired Equivalent Privacy (WEP) algorithm originally designed for the
MAC layer of 802.11 [22-23]. Wired Equivalent Privacy (WEP) was shown to have security
vulnerabilities. Wi-Fi Protected Access (WPA) was introduced by the Wi-Fi Alliance as an
intermediate solution to the WEP insecurities. The Wi-Fi Alliance refers to their interoperable
implementation of the full 802.11i as WPA2, also called RSN (Robust Security Network). The
802.11i standard makes use of the Advanced Encryption Standard (AES) block cipher in contrast
to WEP and WPA which use the RC4 stream cipher [20].Robust Security Network (RSN) comes
with two new protocols. They are:
1. The 4-Way Handshake
2. The Group Key Handshake.
These utilize the authentication services and port access control described in the IEEE 802.1X to
establish as well as change the appropriate cryptographic keys. The RSN is a security network
that only allows for the creation of robust security network associations (RSNAs), a type of
association used by a pair of STAs if the procedure to establish authentication or association
between them includes the 4-Way Handshake. It also provides two RSNA data confidentiality and
integrity protocols such as TKIP and CCMP, with CCMP being mandatory [16].
4.7. IEEE 802.11j
802.11j standard was introduced in 2004 and was designed especially for Japanese market. It
provided Wireless LAN operation in the 4.9 to 5 GHz band so as to conform to the Japanese rules
for radio operation for indoor, outdoor and also mobile applications.
4.8. IEEE 802.11k
For the purpose of radio resource management, IEEE 802.11k defines enhancements that provide
mechanisms available to protocol layers above the physical layer [23]. The standard enabled the
management of the air interface between several APs, including the following:
1. To improve roaming decisions, an AP can provide a site report to a mobile device when the
AP determines that the mobile device is going away from it. The site report lists APs from best to
worst that a mobile device can use in changing over to another AP [24].
2. An AP can collect channel information from each mobile device on the WLAN network. Each
mobile device provides a noise histogram that displays all non-802.11 energy on that channel as

54
perceived by the mobile device. The access point collects the statistics on how long a channel is
in active use during a given time. This data enable the AP to regulate access to a given channel.
3. APs can query mobile devices to collect statistics, such as retries, packets transmitted, and
packets received. This gives the AP a more complete view of the network performance.
4. 802.11k also extended the transmit-power-control procedures as defined in 802.11h standard to
other regulatory domains and frequency bands, to reduce power consumption, interference, and to
provide range control.
4.9. IEEE 802.11l
This standard is reserved and will not be used. Moreover, no task group was named IEEE 802.11l
to avoid confusion with another well known standard IEEE 802.11i.
4.10. IEEE 802.11m
An ongoing task group was put in charge with the maintenance of the standard. The revisions as
well as clarifications and modifications are produced periodically. IEEE 802.11m is an ongoing
initiative that provides a unified view of the 802.11 base standards through continuous
monitoring, management and maintenance. IEEE 802.11m is based on two documented
initiatives. They are:
1. IEEE 802.11ma
2. IEEE 802.11mb
IEEE 802.11ma is comprised of the eight previous standards (a, b, d, e, g, h, i, j) which was
editorially applied through 2003. In addition, IEEE 802.11mb is the current maintenance draft
version.
4.11. IEEE 802.11n
Finally published in 2009, the aim of the IEEE 802.11n is to increase the MAC layer throughput
from the previous standards. First conceived in the year 2002, the IEEE 802.11n task group has
been studying various enhancements to the Physical and MAC layers to improve throughput [25].
These enhancements include items such as changes to signal encoding schemes, multiple
antennas, smart antennas, and changes to MAC protocols [26-28]. IEEE 802.11n introduced new
MAC layer mechanisms to increase throughput. The standard uses MIMO [26] and various new
modulation and coding mechanisms to increase the data rates. The standard uses a fixed channel
bandwidth of 20MHz, which is useful for backward compatibility with older standards. IEEE
802.11n also possesses an optional 40MHz channel. Data rates up to 600 Mbps are achieved only
with the maximum of four spatial streams using one 40 MHz-wide channel [25].
In order to increase the MAC layer efficiency two new mechanisms were introduced in IEEE
802.11n. These were:
1. Frame Aggregation
2. Block Acknowledgement
In the previous MAC layer, a STA waits for some time after sending a MAC frame. There is
severe under utilization when the MAC frames are small. The frame aggregation technique
enabled STAs to aggregate small frames into larger ones. To maximize efficiency, the maximum
frame size is increased thereby allowing longer frames [27]. The Block Acknowledgement
method discussed earlier is similar to the mechanism with the same name as in IEEE 802.11e.
4.12. IEEE 802.11o
Similar to the IEEE 802.11l, no task group was named as IEEE 802.11o to avoid confusion.
4.13. IEEE 802.11p
To provide for wireless access in vehicular environments (WAVE), IEEE 802.11p is an approved
amendment to the IEEE 802.11 standard. It defines enhancements to 802.11 required to support

55
Intelligent Transportation Systems (ITS) applications [29-31]. It includes data exchange between
high-speed passenger vehicles and ambulances and the roadside infrastructure in the licensed ITS
band of 5.9 GHz (5.85-5.925 GHz).In this protocol, the vehicles send information about their
traffic parameters like speed, distance from other vehicles etc. to nearby vehicles. In this way
each vehicle in the corresponding neighbourhood knows about the traffic status and acts
accordingly.
4.14. IEEE 802.11r
Published in the year 2008, IEEE 802.11r or fast BSS transition (FT) enabled wireless
connectivity with secure and fast handoffs between STAs [32]. This standard provided fast
roaming, even for vehicles in motion. It reduced the roaming delay between two basic service sets
(BSS) to less than 50 ms. The standard also refined the mobile client transition process between
APs by redefining the security key negotiation protocol, which permit negotiations and requests
for wireless resources. IEEE 802.11r key strength lies in the IEEE 802.1X security support, which
facilitates the deployment of portable phones with VoIP over Wi-Fi.
4.15. IEEE 802.11s
IEEE 802.11s is an IEEE 802.11 standard for mesh networking. It defines how wireless devices
can interconnect to create a WLAN mesh network, which may be used for static topologies as
well as for ad-hoc networks [36]. Initially in 2003, the 802.11s started as a Study Group of IEEE
802.11. It became a Task Group in 2004. In the following year i.e. in 2005, a call for proposals
was issued, which resulted in the submission of 15 proposals been put to a vote. After a series of
eliminations and mergers, the proposals dwindled to two (the "SEE-Mesh" and "Wi-Mesh"
proposals), which became a joint proposal in 2006 (fig.4).
Network device which is based on the IEEE 802.11s is labelled as mesh STA. Mesh STAs form
mesh links with each other, over which mesh paths can be established using a routing protocol
(fig.4). The 802.11s defines a default mandatory routing protocol Hybrid Wireless Mesh Protocol
or HWMP [37]. But it still allows vendors to operate using alternate protocols. HWMP is inspired
from a combination of AODV and tree-based routing.
Mesh STAs being individual devices use mesh services to communicate with other devices in the
WLAN network. They can also collocate with 802.11 APs and provide access to the mesh
network. Also, mesh STAs can collocate with an 802.11 portal that implements the role of a
gateway and provides access to one or more non-802.11 networks. In both the cases, 802.11s
provides a proxy mechanism to provide addressing support for non-mesh 802 devices, allowing
for end-points to be cognizant of the external addresses.
Figure 4 Mesh Mode Configuration

56
802.11s also provides mechanisms for deterministic network access, a framework for congestion
control and power save [34-36]. There are no defined roles in a mesh — no clients and servers, no
initiators and also no responders. Security protocols used in a mesh must, therefore, be true peer-
to-peer protocols where either side can initiate to the other or both sides can initiate
simultaneously.
A key establishment protocol called "Simultaneous Authentication of Equals" (SAE) defines a
secure password-based authentication technique. SAE is based on Diffie–Hellman key exchange
using finite cyclic groups which can be a primary cyclic group or an elliptic curve. The problem
on using Diffie–Hellman key exchange is that it does not have an authentication mechanism.
Hence to solve the authentication problem, the resulting key is influenced by a pre-shared key as
well as the MAC addresses of both peers [34].
SAE exchange takes place only when both the peers discover each other. On successful
completion of SAE, each peer knows that the other party possesses the mesh password and, as a
by-product of SAE exchange, the two peers establish a cryptographically strong key. The key is
then used with the "Authenticated Mesh Peering Exchange" (AMPE) to establish a secure peering
and derive a session key to protect mesh traffic, including routing traffic [35].
4.16. IEEE 802.11t
The IEEE 802.11t standard regroups recommended practices to test and measure performance in
wireless networks. It was also known as WPP (Wireless Performance Prediction). However as on
date, the standard has been cancelled from the IEEE 802 project.
4.17. IEEE 802.11u
Published in the year 2011 the IEEE 802.11u was developed to improve internetworking with
external non-802.11 networks. This was achieved through network discovery and selection and
QoS map distribution. The network discovery and selection may be provided in the following
ways:
1. The discovery of suitable networks through the advertisement of access network type, roaming
consortium and venue information.
2. Generic Advertisement Service (GAS) provides for Layer 2 transport of an advertisement
protocol’s frames between a mobile device and a server in the network prior to authentication.
The AP is responsible for the relay of a mobile device’s query to a server in the carrier’s network
and for delivering the server’s response back to the mobile.
3. Access Network Query Protocol (ANQP), which is a query and response based protocol used
by a mobile device to discover a range of information, like roaming partners accessible via the
hotspot along with their credential type including the hotspot operator’s domain name; and EAP
method supported for authentication; IP address type availability and other metadata useful in a
mobile device’s network selection process.
The QoS provides a mapping between the IP’s differentiated services code point (DSCP) to over-
the-air Layer 2 priority on a per-device basis, facilitating end-to-end QoS [38]. Nowadays, with
mobile users whose devices can move between 3G and Wi-Fi networks at a low level using
802.21 handoff, there arise needs for a unified and reliable way to authorize their access to all of
those networks. The 802.11u standard provides a common abstraction that all networks regardless
of protocol can use to provide a common authentication experience. Actually, IEEE 802.11u
primarily focuses on on-the-fly authorization between both the STA and the AP [38]. With the
usage of external network authorization, the AP also provides service to the previously unknown
STAs.

57
4.18. IEEE 802.11v
The IEEE 802.11v was introduced in 2011, to enable configuring clients while they are connected
to the network.
4.19. IEEE 802.11w
The IEEE 802.11w was published in 2009 as an add-on to 802.11i covering management frame
security. It introduces protected management frames with the help of mechanisms that enable data
origin authenticity, data integrity and replay protection.
4.20. IEEE 802.11x
This standard was also not used to avoid confusion with IEEE 802.1x.
4.21. IEEE 802.11y
Since the frequency channels at the 2.4 and 5 GHz frequency bands are already occupied by the
WLANs, a new frequency band was defined in the US allowing higher power and thus longer
ranges [39]. The IEEE 802.11y adapts current layers to the new frequency band. To allow for this,
the standard also adds three new concepts:
1. Contention Based Protocol (CBP)
2. Extended Channel Switch Announcement (ECSA)
3. Dependent Station Enablement (DSE)
These have already been discussed in section 3 and explained in details in [39-40].
4.22. IEEE 802.11z
Published in 2010, the IEEE 802.11z provides extensions for Direct Link Setup (DLS). DLS
allows two stations to communicate directly with each other without the requirement of an AP.
This standard basically provides direct-link setup enhancements to the IEEE 802.11 MAC and
PHY, extending direct-link setup to be independent of the AP, in addition to adding power save
capabilities. The direct-link setup is made independent of the AP by tunnelling the protocol
messages inside data frames.
4.23. IEEE 802.11aa
The IEEE 802.11aa specifies enhancements to the IEEE 802.11 medium access control (MAC)
for robust audio video (AV) streaming, at the same time maintaining coexistence with other types
of traffic.
5. UPCOMING STANDARDS
5.1. IEEE 802.11ad
The IEEE 802.11ad also known as WiGig is a relatively new standard published in December
2012. It specification adds a "fast session transfer" feature, enabling the wireless devices to
seamlessly make transition between the legacy 2.4 GHz and 5 GHz bands and the 60 GHz
frequency band [41]. To operate with optimal performance and range criteria, the IEEE 802.11ad
provides the ability to move between the bands ensuring that computing devices are always "best
connected,"
Through the vast improvements in spectral reuse at 60 GHz and an efficient beam forming
technology, IEEE 802.11ad enables great improvements in capacity [42]. Many users in a dense
deployment can all maintain top-speed performance, without interfering with each other or having
to share bandwidth as with the legacy frequency bands [43-44]. The likely enhancements to
802.11 beyond a new 60 GHz PHY include MAC modifications for directional antennas, personal
basic service set, beamforming, fast session transfer between PHYs and spatial reuse.

58
5.2. IEEE 802.11ae
The IEEE 802.11ae introduces a mechanism for prioritization of management frames. A protocol
to communicate management frame prioritization policy is specified in this standard.
5.3. IEEE 802.11ac
One of the important standards currently under development is IEEE 802.11ac. This standard is
expected to be published by the end of 2014. It is expected to provide a multi-station WLAN
throughput of at least 1 Gbps and a single link throughput of at least 500 Mbps [45]. This is
achieved by extending the air interface concepts which are embraced by 802.11n like wider RF
bandwidth (up to 160 MHz), more MIMO spatial streams (up to 8), multi-user MIMO, and high-
density modulation [45-47].
5.4. IEEE 802.11af
The IEEE 802.11af is intended to operate in the TV White Spaces, which is the spectrum already
allocated to the TV broadcasters but not in use at a specific location and time period [12]. It will
use cognitive radio technology to identify white spaces it can use. However, this cognitive
technology will be based on an authorized geolocation database. This database will provide
information on which frequency, at what time and under what conditions networks may operate.
5.5. IEEE 802.11ah
The IEEE 802.11ah is aimed at developing a global WLAN network that will allow user to access
sub carrier frequencies below 1GHz in the ISM band. It will also enable devices based on the
IEEE 802.11 standards to get access to short burst data transmissions like meter data. In addition
it will provide improve coverage range which will allow new applications such as wide area
based sensor networks, sensor backhaul systems and potential Wi-Fi off-loading functions to
emerge [48]. This standard is currently under development and is predicted to be finalized by
2016.
5.6. IEEE 802.11ai
The IEEE 802.11ai is an upcoming standard predicted to be finalized by 2015. It will include a
fast initial link setup (FILS) that could enable an STA to achieve a secure link setup which is less
than 100 ms [49]. A successful link setup process will then allow the STA to send IP traffic with a
valid IP address through the AP.
5.7. IEEE 802.11mc
The IEEE 802.11mc is similar to the IEEE 802.11m and is also scheduled to appoint a working
group with the task of maintenance of the standard around 2015.
5.8. IEEE 802.11aj
The IEEE 802.11aj will provide modifications to the IEEE 802.11ad Physical (PHY) layer and
the Medium Access Control (MAC) layer to enable operation in the Chinese Milli-Meter Wave
(CMMW) frequency bands including the 59-64 GHz frequency band. The amendment is also
intended to maintain backward compatibility with 802.11ad when it operates in the 59-64 GHz
frequency band. The standard shall also define modifications to the PHY and MAC layers to
enable the operation in the Chinese 45 GHz frequency band. This standard is scheduled to be
finalized by the end of 2016.
5.9. IEEE 802.11aq
The WLAN is fast evolving and is no longer one where stations are merely looking for only
access to internet service. This creates opportunities to deliver new services, as the IEEE 802.11
standard needs to be enhanced to better advertise and describe these new services.

59
The IEEE 802.11aq will provide mechanisms that assist in pre-association discovery of services
by addressing the means to advertise their existence and enable delivery of information that
describes them. This information about services is to be made available prior to association by
stations operating on IEEE 802.11 wireless networks. This standard is scheduled to be published
by 2015.
6. PROBLEMS WITH IEEE 802.11
Several amendments of the original IEEE 802.11 standard had been deployed but still there are
many problems associated with the standards which are required to be addressed.
6.1. Security
One of the prime concerns in wireless networking is security. As WLANs operate over the shared
medium, eavesdropping by unauthorized people and critical information may be accessed with
the use of malicious technologies. The initial standard WEP had security flaws which lead the
Wi-fi forum to implement another encryption system WPA and later WPA2. Although WPA and
WPA2 are much more secure and provides good protection still it is not secure enough to be
contend with. More complex encryption algorithms need to be implemented without decreasing
the MAC layer throughput.
6.2. Data Rate
Another serious drawback of IEEE 802.11 wireless network is the data rate, which is quite low as
compared to its wireline IEEE 802.3 counterpart. IEEE 802.11g provides a data rate of 54Mbps.
There was significant improvement in the data rates provided by the IEEE 802.11n extension. The
WWise and TGnSync proposal supported data rates upto 540Mbps and 630Mbps respectively.
However, the 40 MHz channel required to support such data rates are not available in many
countries. The more recent IEEE 802.11ac aims at providing data rates upto 1Gbps. But this data
rate is even still quite low as compared to the 10 GHz capacity of the wireline network standard
802.3n.
6.3. MAC Layer Throughput
Even though the IEEE 802.11g provides a data rate of 54 Mbps, the MAC layer throughput is far
from this value. Detailed studies have shown that with higher data rates, the MAC layer
throughput decreases to 40-50% of the new data rate. A number of factors can be held responsible
for this decrease in throughput such as the link condition overhead of the MAC layer control
headers and usage of the RTS/CTS mechanism. Increasing the PHY layer data rate alone cannot
solve the throughput problem; but the MAC layer also needs to be changed. Two amendments
IEEE 802.11e and IEEE 802.11n both introduce new mechanisms to solve the problem, but these
techniques are far from providing a complete solution.
7. ETSI HIPERLAN FAMILY
Part of the ETSIs BRAN project, is the High Performance Radio Local Area network
(HiperLAN) which is also targeted as wireless local area network. HiperLAN/1 the first standard
to be developed in 1996 supported data rates upto 20Mbps. In 2000, another standard
HiperLAN/2 was deployed which provided data rates upto 54 Mbps. The HiperLAN networks
were developed with more detailed MAC layer mechanisms than it IEEE counterpart.
HiperLAN did not enjoy much success as the IEEE standard in spite of offering high data rates
initially than some of the earlier extensions like IEEE 802.11a and improved MAC layer
mechanisms [50]. No new HiperLAN standards are currently reported to be under development

60
7.1. Physical (PHY) Layer
HiperLAN/1 was designed to operate at a frequency band of 5.15-5.35 GHz. Similarly
HiperLAN/2 also operated at a frequency band of 5.47-5.725 GHz [52]. Unlike IEEE 802.11,
both the HiperLAN standards had a fixed common channel bandwidth of 20MHz. HiperLAN
802.11a had a similar number of non-overlapping channels. A HiperLAN network chooses its
own channel by using a DFS mechanism, which changes the operating frequency of the network
when the current frequency is occupied by another network.
The HiperLAN PHY layer uses OFDM and several modulation techniques along with coding
values for different data rates. Table 2 summarizes the various modulation techniques of the PHY
layer. The range of operation of HiperLAN is 30m indoors to 150m outdoors. Use of
omnidirectional and sectorized antennas could be seen in a HiperLAN BS or STA.
Table 2
HiperLAN PHY layer modulation techniques
Data
Rate
(Mbps)
Modulation Coding
rate
Coded
bits/sub
carrier
6 BPSK 1/2 1
9 BPSK 3/4 1
12 QPSK 1/2 2
18 QPSK 3/4 2
27 16-QAM 9/16 4
36 16-QAM 3/4 4
54 64-QAM 3/4 6
7.2. Data Link Control (DLC) Layer
Similar to its IEEE counterpart, there are two operating modes in HiperLAN also. These are:
1. Centralized Mode
2. Direct Mode
In the centralized mode, all of the network traffic is routed through an AP. In the direct mode, on
the other hand if both the source and the destination for a transmission are in the same network,
the connection is made directly between the source and the destination node. Like in the
centralized mode, the direct mode employs a Central Controller (CC) which is responsible for the
management of all the traffic in the network [50].
DLC layer of HiperLAN uses a Time Division Multiple Access Scheme (TDMA). In HiperLAN
each MAC frame is divided into five phases. They are:
1. Broadcast Phase
2. Downlink Phase
3. Direct Link Phase
4. Uplink Phase
5. Random Access Phase
The first phase which is the broadcast phase mainly contains the broadcast messages of the
network. In addition it also contains the frame structure information i.e. the time information of
both the uplink and downlink phase of the current frame. The uplink and the downlink phases
contain messages which originate from the AP/CC as well as from a WLAN node. If a connection
is specified to be a direct link connection, frames belonging to this connection are sent in the
Direct Link Phase. Association messages and resource allocation messages is transmitted in the
Random Access Phase.

61
In HiperLAN when a STA needs to establish a connection a request for a new connection is sent
to the corresponding AP/CC. IF the AP/CC accepts this request based on the QoS constraints of
the connection and the current network load, it establishes the connection and reserves it
resources accordingly. Otherwise the request is denied. In case of a denial, the STA may retry
with a new request. The QoS connections are set up during connection establishment. There is no
MAC layer throughput limit in HiperLAN.
HiperLAN uses a plane based protocol stack. In this, two planes exist in the protocol where one is
for user data and the other is for control messages. All the data packets are sent over the user
plane and the control packet over the control plane.
7.3. Security
The security in HiperLAN/1was covered in the MAC layer. However HiperLAN/2 addressed the
issue of security with emphasis. The HiperLAN/2 had security functions in the DLC level for
protection against eavesdropping and transmission inception. This was established with the help
of a Data Confidentiality service in the DLC layer. It deployed two encryption-decryption
methods, DES and later Triple DES. However these techniques proved to be quite insecure over
time.
8. HIPERLAN STANDARDS
8.1. HiperLAN/1
The goal of HiperLAN/l was to achieve higher data rates than the ongoing IEEE standard. The
HiperLAN/1 employs the same Physical layer and the Media Access Control part of the Data link
layer like 802.11. In addition, HiperLAN provides a new sub-layer called Channel Access and
Control sublayer (CAC). This sub-layer deals with the access requests which are made to the
networks. The accomplishing of the request is dependent on the usage of the network and the
priority of the request.
CAC layer provides hierarchical independence with Elimination-Yield Non-Pre-emptive Multiple
Access mechanism (EY-NPMA) [51]. EY-NPMA codes priority choices and other functions into
one variable length radio pulse preceding the packet data, enabling the network to function with
few collisions even with a large number of users. Multimedia applications work in HiperLAN
because of EY-NPMA priority mechanism. The MAC layer defines protocols for security, routing
and power saving and provides for naturally transferring data to the upper layers. On the physical
layer FSK and GMSK modulations are used in HiperLAN/1.
8.2. HiperLAN/2
HiperLAN/2 functional specification was accomplished in 2000. The physical layer of
HiperLAN/2 is very similar to IEEE 802.11a standard. However, the media access control is
Dynamic TDMA in HiperLAN/2, while CSMA/CA is used in 802.11a [53].The standard covers
Physical, Data Link Control and Convergence layers.
The Convergence layer takes care of service dependent functionality between DLC and Network
layer. Convergence sub-layers can be used also on the physical layer to connect IP, ATM or
UMTS networks [52]. This feature makes HiperLAN/2 suitable for the wireless connection of
various networks. HiperLAN/2 physical layer makes use of BPSK, QPSK, 16QAM or 64QAM
modulations. HiperLAN/2 for the first time offered security measures. The data were secured
with DES or Triple DES algorithms.
9. FAILURE IN THE MARKET
HiperLAN was basically a European alternative for the IEEE standard. Due to competition from
IEEE 802.11, which was simpler to implement and was released prior to HiperLAN [50],
HiperLAN never received much commercial implementation. Much of the work on HiperLAN/2

62
has lasted in the PHY specification for IEEE 802.11a, which is nearly identical to the PHY
specification of HiperLAN/2.
10. CONCLUSION
Some of the reasons which can be cited for such widespread use of WLANs are low infrastructure
cost, ease of development, support for mobile user communication, deployment without cabling
and ease of adding new user to the network resulting in a huge decrease in implementation cost.
As the importance of mobile user has increased manifold, WLANs have gained much importance
in homes, schools, offices etc and matured as an access technology in short distance
communications.
Still today, WLANs suffers from a lot of problems. One of the most important drawbacks is the
use of shared medium in which performance gets considerably degraded as the number of STAs
increases in the WLAN network. The problem of unauthorized access and eavesdropping in
WLANs are some of the serious security issues which have been a long standing headache for the
IEEE working group. Different security encryption schemes had been implemented in the past.
But so far all such encryption systems have been proven to have security vulnerabilities.
Furthermore a WLAN network provides a contention based access to its users. Contention based
access is a probabilistic access approach where each user in the network competes with others for
access through an Access Point (AP). This approach becomes cumbersome even with a small
network load as small as a classroom. Maintaining a strict QoS is quite troublesome due to
contention and variable link quality problems. Various methods have been implemented to
overcome these problems and more advanced methods are currently under development. Brief
overviews of the standards that belong to the IEEE 802.11 have been summarized in Table 3.
Table 3
IEEE 802.11 family
Standard Purpose Publishing
Date
IEEE 802.11 Originally 1 Mbps and 2 Mbps, 2.4 GHz RF and IR standard 1997
IEEE 802.11a 54 Mbps, 5 GHz PHY layer standard 1999
IEEE 802.11b Enhancements to 802.11 to support 5.5 and 11 Mbps 1999
IEEE 802.11c Bridge operation procedures [now included in the IEEE 802.1D] 2001
IEEE 802.11d Country-to-country roaming extensions 2001
IEEE 802.11e Enhancements: QoS, including packet bursting 2005
IEEE 802.11f Inter-Access Point Protocol [Stands Cancelled] 2003
IEEE 802.11g 54 Mbps, 2.4 GHz standard (backwards compatible with b) 2003
IEEE 802.11h Spectrum Managed 802.11a (5 GHz) for European compatibility 2004
IEEE 802.11i Enhanced security 2004
IEEE 802.11j Extensions for Japan 2004
IEEE 802.11k Radio resource measurement enhancements 2007
IEEE 802.11m Maintenance of the standard
IEEE 802.11n Higher throughput improvements using MIMO 2009
IEEE 802.11p WAVE—Wireless Access for the Vehicular Environment 2010
IEEE 802.11r Fast BSS transition (FT) 2008
IEEE 802.11s Mesh Networking, Extended Service Set (ESS) 2011
IEEE 802.11t Wireless Performance Prediction (WPP)—test methods and metrics Recommendation
[Stands Cancelled]
IEEE 802.11u Improvements related to Hot Spots and 3rd party authorization of clients. 2011
IEEE 802.11v Wireless network management 2011
IEEE 802.11w Protected Management Frames 2009
IEEE 802.11y 3650–3700 MHz Operation in the U.S. 2008
IEEE 802.11z Extensions to Direct Link Setup 2010
IEEE 802.11aa Robust streaming of Audio Video Transport Streams 2012
IEEE 802.11ad Very High Throughput 60 GHz 2012
IEEE 802.11ae Prioritization of Management Frames 2012
IEEE 802.11ac Very High Throughput <6 GHz; potential improvements over 802.11n: better modulation
scheme (expected ~10% throughput increase), wider channels, multi user MIMO.
~2014
IEEE 802.11af TV Whitespace ~2014
IEEE 802.11ah Sub 1 GHz sensor network, smart metering. ~2016
IEEE 802.11ai Fast Initial Link Setup ~2015

63
IEEE 802.11mc Maintenance of the standard ~2015
IEEE 802.11aj China Millimeter Wave ~2016
IEEE 802.11aq Pre-association Discovery ~2015
~ denotes expected year
REFERENCES
[1] IEEE 802.11-1999, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications, June 12, 1999.
[2] IEEE 802.11b-1999, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications High Speed Physical Layer
Extension in the 2.4 GHz Band, September 16, 1999
[3] IEEE 802.11a-1999, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications High Speed Physical Layer
in the 5 GHz Band, 1999.
[4] IEEE 802.11g-2003, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Amendment 4: Further
Higher Data Rate Extension in the 2.4 GHz Band, June 27, 2003.
[5] U.S. Robotics, 802.11g Speed Acceleration How We Do It, www.usr.com/download/whitepapers/125mbps-wp.pdf
2004.
[6] A. Otyakmaz, U. Fornefeld, J. Mirkovic, D.C. Schultz, E.Weiss, Performance evaluation for IEEE 802.11g hot spot
coverage using sectorized antennas, in: 15th IEEE International Symposium on Personal, Indoor and Mobile Radio
Communications (PIMRC ’04), vol. 2, 2004, pp. 1460– 1465.
[7] D. Vassis, G. Kormentzas, A. Rouskas, I. Maglogiannis, The IEEE 802.11g standard for high data rate WLANs, IEEE
Network 19 (3) (2005) 21–26.
[8] IEEE 802.11d-2001, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Amendment 3: Specification for Operation
in Additional Regulatory Domains, 2001.
[9] IEEE 802.11e-2005, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications MAC Enhancements for
QoS, 2005.
[10] A.E. Xhafa, S. Kangude, X. Lu, MAC Performance of IEEE 802.16e, IEEE 62nd Vehicular Technology Conference
2005 (VTC ’05) vol. 1. Dallas, TX, USA, 2005, pp. 685–689.
[11] D.J. Leith, P. Clifford, Using the 802.11e EDCF to achieve TCP upload fairness over WLAN links, in: 3rd
International Symposium on Modeling and Optimization in Mobile, Ad Hoc, and Wireless Networks 2004 (WiOPT
‘05) Trentino, Italy, 2005, pp. 109–118.
[12] Y.P. Fallah, H. Alnuweiri, A controlled-access scheduling mechanism for QoS provisioning in IEEE 802.11e wireless
LANs, in: 1st ACM International Workshop on QoS and Security for Wireless and Mobile Networks 2005
(Q2SWinet ’05) Spring, Canada, 2005, pp. 122–129.
[13] A.C.H. Ng, D. Malone, D.J. Leith, Experimental evaluation of TCP performance and fairness in an 802.11e testbed,
in: ACM Annual Conference of the Special Interest Group on Data Communication 2005 (SIGCOMM ’05)
Philadelphia, PA, USA, 2005, pp. 17–22.
[14] S. Choi, J. del Prado, S. Shankar, S. Mangold, IEEE 802.11e contention-based channel access (EDCF) performance
evaluation, in: IEEE International Conference on Communications (ICC ’03) Anchorage, Alaska, USA, 2003.
[15] Kuran, Mehmet S., and Tuna Tugcu. "A survey on emerging broadband wireless access technologies." Computer
Networks 51.11 (2007): 3013-3046.
[16] Hiertz, G., et al. "The IEEE 802.11 universe." Communications Magazine, IEEE48.1 (2010): 62-70.
[17] Akyildiz, Ian F., and Xudong Wang. "A survey on wireless mesh networks."Communications Magazine, IEEE 43.9
(2005): S23-S30.
[18] Q. Ni, L. Romdhani, T. Turletti, A survey of QoS enhancements for IEEE 802.11 wireless LAN, Wiley Journal of
Wireless Communications and Mobile Computing4 (5) (2004) 547–566.
[19] Konsgen, A., Zakir Hossain, and Carmelita Gorg. "Transmit power control algorithms in ieee 802.11 h based
networks." Personal, Indoor and Mobile Radio Communications, 2005. PIMRC 2005. IEEE 16th International
Symposium on. Vol. 3. IEEE, 2005.
[20] IEEE 802.11i-2004, IEEE Standard for Local and Metropolitan Area Networks Specific Requirements – Part 11:
Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Amendment 6: Medium
Access Control (MAC) Security Enhancements, July 23, 2004.
[21] S. Fluhrer, I. Mantin, A. Shamir, Weakness in the key scheduling algorithm of RC4, in: Springer Eighth Annual
Workshop on Selected Areas in Cryptography 2001 (SAC ’01), vol. 2259, Toronto, Canada, 2001, pp. 1–24.
[22] J. McNair, T. Tugcu, W. Wang, J. Xie, A survey of crosslayer performance enhancements for mobile IP networks,
Elsevier Computer Networks Journal 49 (2) (2005) 19–294.
[23] 802.11k-IEEE Standard for Information technology-Local and metropolitan area networks-Specific requirements-Part
11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications Amendment 1: Radio
Resource Measurement of Wireless LANs, 2008.
[24] Rabaey, Jan, et al. "Connectivity brokerage-enabling seamless cooperation in wireless networks." White Paper), Sept
(2010).

64
[25] Y. Xiao, “IEEE 802.11n: enhancements for higher throughput in wireless LANs”, IEEE Wireless Communications 12
(6) (2005) 82–91.
[26] J.M. Gilbert, W. Choi, Q. Sun, MIMO technology for advanced wireless local area networks, in: 42nd Annual
Conference on Design Automation 2005 (DAC ’05), Anaheim, CA, USA, 2005, pp. 413–415.
[27] Skordoulis, Dionysios, et al. "IEEE 802.11 n MAC frame aggregation mechanisms for next-generation high-
throughput WLANs." Wireless Communications, IEEE 15.1 (2008): 40-47.
[28] Perahia, Eldad. "IEEE 802.11 n development: history, process, and technology." Communications Magazine, IEEE
46.7 (2008): 48-55.
[29] Jiang, Daniel, and Luca Delgrossi. "IEEE 802.11 p: Towards an international standard for wireless access in vehicular
environments." Vehicular Technology Conference, 2008. VTC Spring 2008. IEEE. IEEE, 2008.
[30] Wellens, Matthias, Burkhard Westphal, and Petri Mahonen. "Performance evaluation of IEEE 802.11-based WLANs
in vehicular scenarios." Vehicular Technology Conference, 2007. VTC2007-Spring. IEEE 65th. IEEE, 2007.
[31] Hartenstein, Hannes, and Kenneth P. Laberteaux. "A tutorial survey on vehicular ad hoc networks." Communications
Magazine, IEEE 46.6 (2008): 164-171.
[32] Bangolae, Sangeetha, Carol Bell, and Emily Qi. "Performance study of fast BSS transition using IEEE 802.11 r."
Proceedings of the 2006 international conference on Wireless communications and mobile computing. ACM, 2006.
[33] Wang, Jianfeng, Monisha Ghosh, and Kiran hallapali. "Emerging cognitive radio applications: A survey."
Communications Magazine, IEEE 49.3 (2011): 74-81.
[34] Carrano, Ricardo C., et al. "IEEE 802.11s multihop MAC: A tutorial."Communications Surveys & Tutorials, IEEE
13.1 (2011): 52-67.
[35] P. Djukic, S. Valaee, “802.16 MCF for 802.11a based mesh networks: a case for standards re-use” in: 23rd IEEE
Biennial Symposium on Communications 2006, Kingston, Ont., Canada, 2006, pp. 186–189.
[36] D. Molta, “Primer: mesh configurations applications make a mesh of your WLAN”, Network Computing 11 (17)
(2005) 67–71.
[37] D. Maniezzo, G. Villa, M. Gerla, “A smart MAC-routing protocol for WLAN mesh networks”, UCLA-CSD
Technical Report number 040032, 2004.
[38] Stankiewicz, Rafal, Piotr Cholda, and Andrzej Jajszczyk. "QoX: what is it really?." Communications Magazine, IEEE
49.4 (2011): 148-158.
[39] Khan, Bilal, and Jong-Suk Ahn. "A performance model for the effect of interferences among the collocated
heterogeneous wireless networks."Advanced Communication Technology (ICACT), 2013 15th International
Conference on. IEEE, 2013.
[40] Kim, Eunsun, and Yongho Seok. "Method for Operating a Station in a White Space, and Apparatus for Same." U.S.
Patent No. 20,130,109,403. 2 May 2013.
[41] Perahia, Eldad, et al. "IEEE 802.11 ad: Defining the next generation multi-Gbps Wi-Fi." Consumer Communications
and Networking Conference (CCNC), 2010 7th IEEE. IEEE, 2010.
[42] Cordeiro, Carlos, Dmitry Akhmetov, and Minyoung Park. "Ieee 802.11 ad: introduction and performance evaluation
of the first multi-gbps wifi technology."Proceedings of the 2010 ACM international workshop on mmWave
communications: from circuits to networks. ACM, 2010.
[43] Zhu, Hua, et al. "Distributed Admission Control for IEEE 802.11 Ad Hoc Networks." (2013).
[44] Zhao, Fang, et al. "Comparison of analytical and measured performance results on network coding in IEEE 802.11
ad-hoc networks." Network Coding (NetCod), 2012 International Symposium on. IEEE, 2012.
[45] Ong, Eng Hwee, et al. "IEEE 802.11 ac: Enhancements for very high throughput WLANs." Personal Indoor and
Mobile Radio Communications (PIMRC), 2011 IEEE 22nd International Symposium on. IEEE, 2011.
[46] Park, Minyoung. "IEEE 802.11 ac: Dynamic bandwidth channel access."Communications (ICC), 2011 IEEE
International Conference on. IEEE, 2011.
[47] Van Nee, Richard. "Breaking the Gigabit-per-second barrier with 802.11 AC."Wireless Communications, IEEE 18.2
(2011): 4-4.
[48] Aust, Stefan, R. Venkatesha Prasad, and Ignas GMM Niemegeers. "IEEE 802.11ah: Advantages in standards and
further challenges for sub 1 GHz Wi-Fi." Communications (ICC), 2012 IEEE International Conference on. IEEE,
2012.
[49] Ong, Eng Hwee. "Performance analysis of fast initial link setup for IEEE 802.11ai WLANs." Personal Indoor and
Mobile Radio Communications (PIMRC), 2012 IEEE 23rd International Symposium on. IEEE, 2012.
[50] Weinmiller, Jost, et al. "Performance study of access control in wireless LANs—IEEE 802.11 DFWMAC and ETSI
RES 10 Hiperlan." Mobile networks and applications 2.1 (1997): 55-67.
[51] Hadzi-Velkov, Zoran, and Boris Spasenovski. "Performance comparison of IEEE 802.11, and ETSI HIPERLAN type
1 under influence of burst noise channel."Wireless Communications and Networking Confernce, 2000. WCNC. 2000
IEEE. Vol. 3. IEEE, 2000.
[52] ETSI HiperLAN/2, Broadband Radio Access Networks (BRAN); High Performance Radio Local Area Network
(HIPERLAN) Type 2; Requirements and Architecture for Wireless Broadband Access, January 1999.
[53] ETSI HiperLAN/2, Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; System Overview, February
2002.

ON IEEE 802.11: WIRELESS LAN TECHNOLOGY

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to ON IEEE 802.11: WIRELESS LAN TECHNOLOGY (20)

Recently uploaded (20)

ON IEEE 802.11: WIRELESS LAN TECHNOLOGY