Ppt on water level indicator

Water Level
Indicator With
Alarm
Submitted To:
Er.Gurinder Singh Submitted By :
Palwinder Kaur
121356123078
Electronics and
communication
engg.

Embedded
system
 An embedded system is some combination of
computer hardware and software, either fixed in
capability or programmable, that is specifically
designed for a particular function. Industrial
machines, automobiles, medical equipment, cameras,
household appliances, airplanes, vending machines
and toys (as well as the more obvious cellular phone
and PDA) are among the myriad possible hosts of an
embedded system. Embedded systems that are
programmable are provided with programming
interfaces, and embedded systems programming is a
specialized occupation.

Applications of
embedded system
Telecommunication
Aerospace and Avionics
Railroad
Consumer Electronics
Electronic payment solution sector
Smart cards industries

Water Level Indicator
With Alarm
 The Water Level Indicator employs a simple mechanism
to detect and indicate the water level in an overhead tank
or any other water container. The sensing is done by using
a set of seven probes which are placed at seven different
levels on the tank walls (with probe 7 to probe 1 placed in
increasing order of height, common probe (i.e. a supply
carrying probe) is placed at the base of the tank). The
level 7 represents the “tank full” condition while level 1
represents the “tank empty” condition.

Water level indicator
project circuit
features
 Easy installation.
 Low maintenance.
 Compact elegant design.
 The Automatic water level controller ensures no overflows
or dry running of pump there by saves electricity and water.
 Avoid seepage of roofs and walls due to overflowing tanks.
 Fully automatic, saves man power.
 Consume very little energy, ideal for continuous operation
 Shows clear indication of water levels in the overhead tank.

circuit diagram

Components used
Resistors: 470 ohms,33ohms
and 470kohms
Transistors
Speaker
Different colour LEDs
Diodes

Resistors:
 A resistor is an electrical component that limits or
regulates the flow of electrical current in an electronic
circuit. Resistors can also be used to provide a
specific voltage for an active device such as a transistor.

Tranisters:
 A transistor is a semiconductor device used
to amplify and switch electronic signals and electrical
power. It is composed of semiconductor material with
at least three terminals for connection to an external
circuit. A voltage or current applied to one pair of the
transistor's terminals changes the current through
another pair of terminals. Because the controlled
(output) power can be higher than the controlling
(input) power, a transistor can amplify a signal. Today,
some transistors are packaged individually, but many
more are found embedded in integrated circuits.

LEDs:
 Stands for "Light-Emitting Diode." An LED is an
electronic device that emits light when an electrical
current is passed through it. Early LEDs produced only
red light, but modern LEDs can produce several
different colors, including red, green, and blue (RGB)
light. Recent advances in LED technology have made it
possible for LEDs to produce white light as well.
 LEDs are commonly used for indicator lights (such as
power on/off lights) on electronic devices

Diodes:
 A diode is a specialized electronic component with two
electrodes called the anode and thecathode. Most
diodes are made with semiconductor materials such as
silicon, germanium, or selenium. Some diodes are
comprised of metal electrodes in a chamber evacuated
or filled with a pure elemental gas at low pressure.
Diodes can be used as rectifiers, signal limiters, voltage
regulators, switches, signal modulators, signal mixers,
signal demodulators, and oscillators.

description
 This is the circuit diagram and description for water level indicator.
 A constant 5v power supply is given to the microcontroller and rest of the
circuit from a battery.
 The tank has 9 conductive type sensors (other types of sensors have been
mentioned earlier but in our project only conductive type are used) embedded
into it and 8 wires of sensors out of 9 are connected to transistors and the 9th is
connected to 5v+ supply.
 The use of transistor is it acts as inverter (i.e. in on state gives low voltage at
output and in non conducting state gives high voltage at its output), all
transistors outputs are connected to 1,2,3,4,5,6,7,8 pins (PORTB) of
microcontroller.
 Seven segment display is connected to pin no. 33 to 40 (PORTA). It is
connected in common cathode fashion.
The Output for the 7th level is not only shown in seven segment display but
also indicated with a discontinuous buzzer sound.
 Output for the 8th level (i.e. tank full condition) is not only shown in seven
segment display but also indicated with a continuous buzzer sound.

Working of water level
indicator with alarm
 The operation of this project is very simple and can be
understood easily. In our project “water level
indicator” there are 3 main conditions:
 There is no water available in the source tank.
 Intermediate level i.e. either of 3rd to 7th level.
 There is ample amount of water available in the source
tank.
 So let us discuss on the more about these 3 conditions

Condition 1:Water is not
available
 When the tank is empty there is no conductive path
between any of the 8 indicating probes and the common
probe (which is connected to 5v+ supply) so the transistor
base emitter region will not have sufficient biasing voltage
hence it remains in cut off region and the output across its
collector will be Vc approximately 4.2v. As in this case the
microcontroller is used in the active low region (which
means it considers 0-2 volts for HIGH and 3-5 volts for
LOW) now the output of transistor which is 4.2v
approximately will be considered as LOW by the
microcontroller and hence the default value given by
microcontroller to the seven segment display is 1 which
indicates as the tank is empty.

Condition 2:
intermediate levels
 Now as the water starts filling in the tank a conductive path
is established between the sensing probes and the common
probe and the corresponding transistors get sufficient
biasing at their base, they starts conducting and now the
outputs will be Vce (i.e. 1.2v-1.8v) approximately which is
given to microcontroller. Here the microcontroller is
programmed as a priority encoder which detects the
highest priority input and displays corresponding water
level in the seven segment display. In this project while the
water level reaches the 7th level i.e. last but one level along
with display in seven segment a discontinuous buzzer is
activated which warns user that tank is going to be full
soon.

Condition 3:Water full
 When the tank becomes full, the top level probe gets
the conductive path through water and the
corresponding transistor gets into conduction whose
output given to microcontroller with this input
microcontroller not only displays the level in seven
segment display but also activates the continuous
buzzer by which user can understand that tank is full
and can switch off the motor and save water.

Applications of water
level indicator
 Automatic Water level Controller can be used in Hotels,
Factories, Homes Apartments, Commercial Complexes,
Drainage, etc., It can be fixed for single phase motor, Single
Phase Submersibles, Three Phase motors. (For 3Æ and
Single Phase Submersible Starter is necessary) and open
well, Bore well and Sump. We can control two motor and
two sumps and two overhead tanks by single unit.
 Automatic water level controller will automatically START
the pump set as soon as the water level falls below the
predetermined level (usually 1/2 tank) and shall SWITCH
OFF the pump set as soon as tank is full.
 Fuel level indicator in vehicles.
 Liquid level indicator in the huge containers in the
companies.

Ppt on water level indicator

More Related Content

What's hot

Similar to Ppt on water level indicator

Recently uploaded

In this document

Ppt on water level indicator