Raspberry pi on seminar documentation

Raspberry pi SeminarReport
College 1 BSc ComputerScience
INTRODUCTION

INTRODUCTION
Raspberry Pi is a credit-card sized computer manufactured and designed in the United Kingdom by
the Raspberry Pi foundation with the intention of teaching basic computer science to school students
and every other person interested in computer hardware, programming and DIY-Do-it Yourself
projects.
The Raspberry Pi is manufactured in three board configurations through licensed manufacturing
deals with Newark element14 (Premier Farnell), RS Components and Egoman. These companies sell
the Raspberry Pi online. Egoman produces a version for distribution solely in China and Taiwan,
which can be distinguished from other Pis by their red coloring and lack of FCC/CE marks. The
hardware is the same across all manufacturers.
The Raspberry Pi has a Broadcom BCM2835 system on a chip (SoC), which includes an
ARM1176JZF-S 700 MHz processor, VideoCore IV GPU and was originally shipped with 256
megabytes of RAM, later upgraded (Model B & Model B+) to 512 MB. It does not include a built-in
hard disk or solid-state drive, but it uses an SD card for booting and persistent storage, with the
Model B+ using a MicroSD.
The Foundation provides Debian and Arch Linux ARM distributions for download. Tools are
available for Python as the main programming language, with support for BBC BASIC (via the RISC
OS image or the Brandy Basic clone for Linux), C, Java and Perl.
As of February 2014, about 2.5 million boards had been sold.
The board is available online in India at a price of Rs. 3000.

EVOLUTION

History of Computers
A brief history of ultra-cheap and small computers:
Computers were very expensive during the 1950’s. Computers of that time were used in weather
forecasting, plotting values of logarithmic functions and other complex calculations. They were huge
machines with little or no operating systems. They needed dedicated air-conditioned rooms and
special trained operators. Examples of these include the ENIAC, the ZUSE Z3 etc. Then vacuum
tubes were replaced by bipolar transistors, which made those huge machines a bit smaller. The
invention of Integrated Circuit(IC) gave computers a huge leap in terms of computing power and a
basis for personal computers.
In those days portable computers were available which were essentially payroll machines or had
other dedicated applications. Most of them were used for single purpose such as printing bills, as
calculators, digital diaries etc.
Apple released Lisa in 1983 and marked a new point in the history of computers. For the first time a
Graphical User Interface (GUI) was introduced in a computer that was cheap and most small
businesses could afford. Microsoft tried the same thing and released DOS which was a huge success
for the IBM PC. Now people could afford their own computer for their home. IBM PC sparked a
massive explosion of personal computers. People started buying computers for their homes and
offices like never before. Now kids could play games on them, adults could do their spreadsheets etc.
During the decade of 80’s, the advent of laptops or notebook computers started. Many companies
and vendors released the then portable computers which were the basis for the modern laptops. The
first mass-produced microprocessor-based portable computer was the Osborne 1 in 1981,
which used the CP/M operating system. Then within a few years, in 1986, Toshiba released the
T1100, which they described as the “world’s first mass-market laptop computer”.

Figure 1: Osborne 1 Computer Figure 2: Toshiba T1100
As technology improved during the 1990s, the usefulness and popularity of laptops increased.
Correspondingly prices went down. Several developments specific to laptops like improved battery
technology, power saving processors, improved Liquid Crystal Displays, improved storage etc. were
quickly implemented, improving usability and performance.
History of Embedded Devices
In the earliest years of computers in the 1930–40s, computers were sometimes dedicated to a single
task, but were far too large and expensive for most kinds of tasks performed by embedded computers
of today. Over time however, the concept of programmable controllers evolved from traditional
electromechanical sequencers, via solid state devices, to the use of computer technology.
One of the first recognizably modern embedded systems was the Apollo Guidance Computer,
developed by Charles Stark Draper at the MIT Instrumentation Laboratory. At the project's
inception, the Apollo guidance computer was considered the riskiest item in the Apollo project as it
employed the then newly developed monolithic integrated circuits to reduce the size and weight. An
early mass-produced embedded system was the Autonetics D-17 guidance computer for the
Minuteman missile, released in 1961. It was built from transistor logic and had a hard disk for main
memory. When the Minuteman II went into production in 1966, the D-17 was replaced with a new

computer that was the first high-volume use of integrated circuits. This program alone reduced prices
on quad NAND gate ICs from $1000/each to $3/each, permitting their used.
Since these early applications in the 1960s, embedded systems have come down in price and there
has been a dramatic rise in processing power and functionality. The first microprocessor for example,
the Intel 4004, was designed for calculators and other small systems but still required many external
memory and support chips. In 1978 National Engineering Manufacturers Association released a
"standard" for programmable microcontrollers, including almost any computer-based controllers,
such as single board computers,
As the cost of microprocessors and microcontrollers fell it became feasible to replace expensive
knob-based analogue components such as potentiometers and variable capacitors with up/down
buttons or knobs read out by a microprocessor even in some consumer products. By the mid-1980s,
most of the common previously external system components had been integrated into the same chip
as the processor and this modern form of the microcontroller allowed an even more widespread use,
which by the end of the decade were the norm rather than the exception for almost all electronics
devices.
The integration of microcontrollers has further increased the applications for which embedded
systems are used into areas where traditionally a computer would not have been considered. A
general purpose and comparatively low-cost microcontroller may often be programmed to fulfil the
same role as a large number of separate components. Although in this context an embedded system is
usually more complex than a traditional solution, most of the complexity is contained within the
microcontroller itself. Very few additional components may be needed and most of the design effort
is in the software. The intangible nature of software makes it much easier to prototype and test new
revisions compared with the design and construction of a new circuit not using an embedded
processor.

Inception of RaspberryPi
The Idea to create the Raspberry Pi
The idea behind a tiny and affordable computer for kids came in 2006, when Eben Upton, Rob
Mullins, Jack Lang and Alan Mycroft, based at the University of Cambridge’s Computer Laboratory,
became concerned about the year-on-year decline in the numbers and skills levels of the A Level
students applying to read Computer Science. From a situation in the 1990s where most of the kids
applying were coming to interview as experienced hobbyist programmers, the landscape in the 2000s
was very different; a typical applicant might only have done a little web design.
Something had changed the way kids were interacting with computers. A number of problems were
identified: majority of curriculums with lessons on using Word and Excel, or writing webpages; the
end of the dot-com boom; and the rise of the home PC and games console to replace the Amigas,
BBC Micros, Spectrum ZX and Commodore 64 machines that people of an earlier generation
learned to program on.
Figure 3: A complete Commodore 64 System

There isn’t much any small group of people can do to address problems like an inadequate school
curriculum or the end of a financial bubble. But those students felt that they could try to do
something about the situation where computers had become so expensive and arcane that
programming experimentation on them had to be forbidden by parents; and to find a platform that,
like those old home computers, could boot into a programming environment. Thus came the idea of
creating the device which kids could buy and learn programming or hardware on – The Raspberry Pi.
Initial Design Considerations
From 2006 to 2008 they created many designs and prototypes of what we now know as the
Raspberry Pi. One of the earliest prototypes is shown below:
Figure 4: One of the earliest prototypeof thePi

These boards use an Atmel ATmega644 microcontroller clocked at 22.1MHz, and a 512K SRAM for
data and frame buffer storage.By 2008, processors designed for mobile devices were becoming more
affordable, and powerful enough to provide excellent multimedia, a feature which would make the
board desirable to kids who wouldn’t initially be interested in a purely programming-oriented device.
The project started to look very realisable and feasible. Eben (now a chip architect at Broadcom),
Rob, Jack and Alan, teamed up with Pete Lomas, MD of hardware design and manufacture company
Norcott Technologies, and David Braben, co-author of the BBC Micro game Elite, to form the
Raspberry Pi Foundation to make it a reality. Three years later, the Raspberry Pi Model B entered
mass production through licensed manufacture deals with Element 14/Premier Farnell and RS
Electronics, and within two years it had sold over two million units!

IMPLEMENTATION

Hardware Layout
Figure 5: Block Diagram of Raspberry Pi
A brief description of the components on the Pi.
1) Processor / SoC (System on Chip)
The Raspberry Pi has a Broadcom BCM2835 System on Chip module. It has a
ARM1176JZF-S processor

The Broadcom SoC used in the Raspberry Pi is equivalent to a chip used in an old
smartphone (Android or iPhone). While operating at 700 MHz by default, the Raspberry Pi
provides a real world performance roughly equivalent to the 0.041 GFLOPS. On the CPU
level the performance is similar to a 300 MHz Pentium II of 1997-1999, but the GPU,
however, provides 1 Gpixel/s, 1.5 Gtexel/s or 24 GFLOPS of general purpose compute and
the graphics capabilities of the Raspberry Pi are roughly equivalent to the level of
performance of the Xbox of 2001. The Raspberry Pi chip operating at 700 MHz by default,
will not become hot enough to need a heats ink or special cooling.
2) Power source
The Pi is a device which consumes 700mA or 3W or power. It is powered by a MicroUSB
charger or the GPIO header. Any good smartphone charger will do the work of powering the
Pi.
3) SD Card
The Raspberry Pi does not have any onboard storage available. The operating system is
loaded on a SD card which is inserted on the SD card slot on the Raspberry Pi. The operating
system can be loaded on the card using a card reader on any computer.
4) GPIO
GPIO – General Purpose Input Output
General-purpose input/output (GPIO) is a generic pin on an integrated circuit whose
behavior, including whether it is an input or output pin, can be controlled by the user at run
time.
GPIO pins have no special purpose defined, and go unused by default. The idea is that
sometimes the system designer building a full system that uses the chip might find it useful to
have a handful of additional digital control lines, and having these available from the chip can
save the hassle of having to arrange additional circuitry to provide them.

GPIO capabilities may include:
 GPIO pins can be configured to be input or output
 GPIO pins can be enabled/disabled
 Input values are readable (typically high=1, low=0)
 Output values are writable/readable
 Input values can often be used as IRQs (typically for wakeup events)
The production Raspberry Pi board has a 26-pin 2.54 mm (100 mil) expansion header,
marked as P1, arranged in a 2x13 strip. They provide 8 GPIO pins plus access to I²C, SPI,
UART), as well as +3.3 V, +5 V and GND supply lines. Pin one is the pin in the first column
and on the bottom row.
Figure 6: GPIO connectoron RPi
5) DSI Connector The Display Serial Interface (DSI) is a specification by the Mobile Industry
Processor Interface (MIPI) Alliance aimed at reducing the cost of display controllers in a

mobile device. It is commonly targeted at LCD and similar display technologies. It defines a
serial bus and a communication protocol between the host (source of the image data) and the
device (destination of the image data).
A DSI compatible LCD screen can be connected through the DSI connector, although it may
require additional drivers to drive the display.
6) RCA Video
RCA Video outputs (PAL and NTSC) are available on all models of Raspberry Pi. Any
television or screen with a RCA jack can be connected with the RPi.
Figure 7: RCA Video Connector
7) Audio Jack
A standard 3.5 mm TRS connector is available on the RPi for stereo audio output. Any
headphone or 3.5mm audio cable can be connected directly. Although this jack cannot be
used for taking audio input, USB mics or USB sound cards can be used.
8) Status LEDs
There are 5 status LEDs on the RPi that show the status of various activities as follows:
“OK” – SD Card Access (via GPIO16) – labeled as "OK" on Model B Rev1.0 boards and
"ACT" on Model B Rev2.0 and Model A boards
“POWER” - 3.3 V Power – labeled as "PWR" on all boards

“FDX” - Full Duplex (LAN) (Model B) – labeled as "FDX" on all boards
“LNK” - Link/Activity (LAN) (Model B) – labeled as "LNK" on all boards
“10M/100” - 10/100Mbit (LAN) (Model B) – labeled (incorrectly) as "10M" on Model B
Rev1.0 boards and "100" on Model B Rev2.0 and Model A boards
Figure 8: Status LEDs
9) USB 2.0 Port
USB 2.0 ports are the means to connect accessories such as mouse or keyboard to the
Raspberry Pi. There is 1 port on Model A, 2 on Model B and 4 on Model B+. The number of
ports can be increased by using an external powered USB hub which is available as a
standard Pi accessory.

10) Ethernet port is available on Model B and B+. It can be connected to a network or internet
using a standard LAN cable on the Ethernet port. The Ethernet ports are controlled by
Microchip LAN9512 LAN controller chip.
11) CSI connector
CSI – Camera Serial Interface is a serial interface designed by MIPI (Mobile Industry
Processor Interface) alliance aimed at interfacing digital cameras with a mobile processor.
The RPi foundation provides a camera specially made for the Pi which can be connected with
the Pi using the CSI connector.
12) JTAG headers
JTAG is an acronym for ‘Joint Test Action Group', an organization that started back in the
mid 1980's to address test point access issues on PCB with surface mount devices. The
organization devised a method of access to device pins via a serial port that became known as
the TAP (Test Access Port). In
1990 the method became a recognized international standard (IEEE Std 1149.1). Many
thousands of devices now include this standardized port as a feature to allow test and design
engineers to access pins.
13) HDMI
HDMI – High Definition Multimedia Interface
HDMI 1.3 a type A port is provided on the RPi to connect with HDMI screens.

4.3 Specifications
Model A Model B Model B+
Target price: US$25 US$35
SoC: Broadcom BCM2835 (CPU, GPU, DSP, SDRAM, and single USB port)
CPU: 700 MHz ARM1176JZF-S core (ARM11 family, ARMv6 instruction set)
GPU: Broadcom Video Core IV @ 250 MHz
Memory
(SDRAM):
256 MB (shared with
GPU)
512 MB (shared with GPU) as of 15 October 2012
USB 2.0 ports: 1 (direct from
BCM2835 chip)
2 (via the on-board 3-
port USB hub)
4 (via the on-board 5-port
USB hub)
Video input: 15-pin MIPI camera interface (CSI) connector, used with the Raspberry Pi
Camera Add-on.
Video outputs: Composite RCA (PAL and NTSC) –in model B+ via 4-pole 3.5 mm jack,
HDMI (rev 1.3 & 1.4), raw LCD Panels via DS
Audio outputs: 3.5 mm jack, HDMI, and, as of revision 2 boards, I²S audio (also potentially
for audio input)
Onboard storage: SD / MMC / SDIO card slot (3.3 V card power
support only)
MicroSD
Onboard network: None 10/100 Mbit/s Ethernet (8P8C) USB adapter on the

third/fifth port of the USB hub
Low-level
peripherals:
8× GPIO, UART, I²C bus, SPI bus with two chip
selects, I²S audio +3.3 V, +5 V, ground
17× GPIO
Power ratings: 300 mA (1.5 W) 700 mA (3.5 W) 600 mA (3.0 W)
Power source: 5 V via MicroUSB or GPIO header
Size: 85.60 mm × 56 mm (3.370 in × 2.205 in) – not including protruding
connectors
Weight: 45 g (1.6 oz)
Table 1 Specifications
Brief description of System on Chip (SoC)
Since smartphones and tablets are basically smaller computers, they require pretty much the same
components we see in desktops and laptops in order to offer us all the amazing things they can do
(apps, music and video playing, 3D gaming support, advanced wireless features, etc).
But smartphones and tablets do not offer the same amount of internal space as desktops and laptops
for the various components needed such as the logic board, the processor, the RAM, the graphics
card, and others. That means these internal parts need to be as small as possible, so that device
manufacturers can use the remaining space to fit the device with a long-lasting battery life.
Thanks to the wonders of miniaturization, SoC manufacturers, like Qualcomm, NVidia or Texas
Instruments, can place some of those components on a single chip, the System on a Chip that powers
smartphones.
A system on a chip or system on chip (SoC or SOC) is an integrated circuit (IC) that integrates all
components of a computer or other electronic system into a single chip. It may contain digital,
analog, mixed-signal, and often radio-frequency functions—all on a single chip substrate. SoCs are

very common in the mobile electronics market because of their low power consumption. A typical
application is in the area of embedded systems.
The contrast with a microcontroller is one of degree. Microcontrollers typically have under 100 kB
of RAM (often just a few kilobytes) and often really are single-chip-systems, whereas the term SoC
is typically used for more powerful processors, capable of running software such as the desktop
versions of Windows and Linux, which need external memory chips (flash, RAM) to be useful, and
which are used with various external peripherals. In short, for larger systems, the term system on a
chip is a hyperbole, indicating technical direction more than reality: increasing chip integration to
reduce manufacturing costs and to enable smaller systems. Many interesting systems are too complex
to fit on just one chip built with a process optimized for just one of the system's tasks.
A typical SoC consists of:
 A microcontroller, microprocessor or DSP core(s). Some SoCs—called multiprocessor
system on chip (MPSoC)—include more than one processor core.
 memory blocks including a selection of ROM, RAM, EEPROM and flash memory
 timing sources including oscillators and phase-locked loops
 peripherals including counter-timers, real-time timers and power-on reset generators
 external interfaces, including industry standards such as USB, FireWire, Ethernet, USART,
SPI
 analog interfaces including ADCs and DACs
 voltage regulators and power management circuits
 A bus - either proprietary or industry-standard such as the AMBA bus from ARM Holdings -
connects these blocks. DMA controllers route data directly between external interfaces and
memory, bypassing the processor core and thereby increasing the data throughput of the SoC.

Accessories
Raspberry Pi being a very cheap computer has attracted millions of users around the world. Thus it
has a large user base. Many enthusiasts have created accessories and peripherals for the Raspberry
Pi. This range from USB hubs, motor controllers to temperature sensors. There are some official
accessories for the RPi as follows:
Camera – On 14 May 2013, the foundation and the distributors RS Components & Premier
Farnell/Element 14 launched the Raspberry Pi camera board with a firmware update to support it.
The Raspberry Pi camera board contains a 5 MPixel sensor, and connects via a ribbon cable to the
CSI connector on the Raspberry Pi. In Raspbian support can be enabled by the installing or
upgrading to the latest version of the OS and then running Raspi-config and selecting the camera
option. The cost of the camera module is 20 EUR in Europe (9 September 2013). and supports
1080p, 720p, 640x480p video. The footprint dimensions are 25 mm x 20 mm x 9 mm.
Gertboard – A Raspberry Pi Foundation sanctioned device designed for educational purposes, and
expands the Raspberry Pi's GPIO pins to allow interface with and control of LEDs, switches, analog
signals, sensors and other devices. It also includes an optional Arduino compatible controller to
interface with the Pi. The Gertboard can be used to control motors, switches etc. for robotic projects.

Figure 9: Gertboard (left) & Raspberry Pi(Right)
USB Hub – Although not an official accessory, it is a highly recommended accessory for the Pi. A
powered USB Hub with 7 extra ports is available at almost all online stores. It is compulsory to use a
USB Hub to connect external hard disks or other accessories that draw power from the USB ports, as
the Pi cannot give power to them.

WORKING

Operating System
The Raspberry Pi primarily uses Linux kernel-based operating systems. The ARM11 is based on
version 6 of the ARM which is no longer supported by several popular versions of Linux, including
Ubuntu. The install manager for Raspberry Pi is NOOBS. The OSs included with NOOBS are:
 Archlinux ARM
 OpenELEC
 Pidora (Fedora Remix)
 Raspbmc and the XBMC open source digital media center
 RISC OS – The operating system of the first ARM-based computer
 Raspbian (recommended) – Maintained independently of the Foundation; based on ARM
hard-float (armhf)-Debian 7 'Wheezy' architecture port, that was designed for a newer
ARMv7 processor whose binaries would not work on the Rapberry Pi, but Raspbian is
compiled for the ARMv6 instruction set of the Raspberry Pi making it work but with slower
performance. It provides some available deb software packages, pre-compiled software
bundles. A minimum size of 2 GB SD card is required, but a 4 GB SD card or above is
recommended. There is a Pi Store for exchanging programs. The 'Raspbian Server Edition
(RSEv2.4)', is a stripped version with other software packages bundled as compared to the
usual desktop computer oriented Raspbian.
Boot Process
The Raspberry Pi does not boot as a traditional computer. The VideoCore i.e. the Graphics processor
actually boots before the ARM CPU.
The boot process of the Raspberry Pi can be explained as follows:
 When the power is turned on, the first bits of code to run is stored in a ROM chip in the SoC
and is built into the Pi during manufacture. This is the called the first-stage bootloader.

 The SoC is hardwired to run this code on startup on a small RISC Core (Reduced Instruction
Set Computer). It is used to mount the FAT32 boot partition in the SDCard so that the
second-stage
 bootloader can be accessed. So what is this ‘second-stage bootloader’ stored in the SD Card?
It’s ‘bootcode.bin’. This file can be seen while mount process of an operating system on the
SD Card in windows.
 Now here’s something tricky. The first-stage bootloader has not yet initialized the ARM CPU
(meaning CPU is in reset) or the RAM. So, the second-stage bootloader also has to run on
the GPU. The bootloader.bin file is loaded into the 128K 4 way set associative L2 cache of
the GPU and then executed. This enables the RAM and loads start.elf which is also in the SD
Card. This is the third-stage bootloader and is also the most important. It is the firmware for
the GPU, meaning it contains the settings or in our case, has instructions to load the settings
from config.txt which is also in the SD Card. We can think of the config.txt as the ‘BIOS
settings’.
 The start.elf also splits the RAM between the GPU and the ARM CPU. The ARM only has
access the to the address space left over by the GPU address space. For example, if the GPU
was allocated addresses from 0x000F000 – 0x0000FFFF, the ARM has access to addresses
from 0x00000000 – 0x0000EFFF.
 The physical addresses perceived by the ARM core is actually mapped to another
address in the VideoCore (0xC0000000 and beyond) by the MMU (Memory
Management Unit) of the VideoCore.
 The config.txt is loaded after the split is done so the splitting amounts cannot be specified in
the config.txt. However, different .elf files having different splits exist in the SD Card. So,
depending on the requirement, the file can be renamed to start.elf and boot the Pi. In the Pi,
the GPU is King!

 Other than loading config.txt and splitting RAM, the start.elf also loads cmdline.txt if it
exists. It contains the command line parameters for whatever kernel that is to be loaded. This
brings us to the final stage of the boot process. The start.elf finally loads kernel.img which
is the binary file containing the OS kernel and releases the reset on the CPU. The ARM CPU
then executes whatever instructions in the kernel.img thereby loading the operating system.

 After starting the operating system, the GPU code is not unloaded. In fact, start.elf is not just
firmware for the GPU, It is a proprietary operating system called VideoCore OS (VCOS).
When the normal OS (Linux) requires an element not directly accessible to it, Linux
communicates with VCOS using the mailbox messaging system
Figure 10: Boot process of Raspberry Pi
Third Stage Bootloader
bootcode.bin starts start.elf which splits the ram. Then load kernel.img. Operating
System is now loaded.
Second Stage Bootloader
Mount bootcode.bin from FAT32 boot partition from SD Card to L2 cache of GPU.
Power On
Hardwired First Stage Bootloader

The NOOBS installer
The Raspberry Pi package only comes with the main board and nothing else. It does not come
shipped with an operating system. Operating systems are loaded on a SD card from a computer and
then the SD card is inserted in the Pi which becomes the primary boot device.
Installing operating system can be easy for some enthusiasts, but for some beginners working with
image files of operating systems can be difficult. So the Raspberry Pi foundation made a software
called NOOBS – New Out Of Box Software which eases the process of installing an operating
system on the Pi.
The NOOBS installer can be downloaded from the official website. A user only needs to connect a
SD card with the computer and just run the setup file to install NOOBS on the SD card. Next, insert
the card on the Raspberry Pi. On booting the first time, the NOOBS interface is loaded and the user
can select from a list of operating systems to install. It is much convenient to install the operating
system this way. Also once the operating system is installed on the card with the NOOBS installer,
every time the Pi boots, a recovery mode provided by the NOOBS can be accessed by holding the
shift key during boot. It also allows editing of the config.txt file for the operating system

Raspberry Pi compatible operating systems
Distribution Type Memory
footprint
Packages
Arch Linux ARM Linux 8,700
BerryTerminal Linux
Bodhi Linux Raspbian 35,000+
ARMHF
Debian ARM Linux 20,000+
Fedora Remix Linux 16,464?
Gentoo Linux Linux ~23 MiB
IPFire Linux ~20 MiB 144
I2PBerry Linux 20,000+
Meego MER + XBMC Linux (embedded) ~34 MiB +
XBMC
~320 (core)
Moebius Raspbian ~20 MiB (core) + Raspbian
Repositories
nOS Linux ~90 MiB 35,000+
openSUSE Linux 3.11 28 MiB (inc.
X11)
6300
OpenWRT Linux 3,3MiB 3358
PiBang Linux Linux_3.6.11 &
SystemD
PwnPi Linux 20,000+
QtonPi Linux
VPNbian Linux ~40 MiB w/o
desktop
35,000+
Raspbian Linux ~30 MiB w/o
desktop
35,000+

OpenELEC Linux 3.10.16
(embedded)
95 MiB (incl.
XBMC)
~140 (+ 7 via xbmc)
XBian Raspbian 35,000+
raspbmc Raspbian 20,000+
RISC OS RISC OS
Aros hosted on Raspbian
Limited Demo
Mixed Debian6 and
Aros
<~50 MiB
Plan9 Plan 9
SlaXBMCRPi Linux 3.10.36+ 476
(+ Official SlackwareARM
14.1 Packages)
PiMAME Linux
PiBox Linux/Buildroot
pipaOS Raspbian ~32 MiB 37.500
Raspberry WebKiosk Raspbian
Volumio Raspbian
Nard SDK Embedded Linux ~40 MB
Table 2: List of supported Operating Systems

APPLICATIONS

Applications The major aim behind the Raspberry Pi was to educate people, especially
children and teenagers, towards programming and basic hardware interfacing. The open body
structure of the Raspberry Pi makes it a machine on which one can learn computer concepts.
Applications of the Raspberry Pi can be given as follows:
 Teaching programming concepts.
 Teaching hardware interfacing.
 Raspberry Pi being very cost effective can be deployed in large numbers in underdeveloped
and developing countries like Africa, India, China, Brazil etc. to schools and colleges and to
everyone who is interested in computers and electronics.
 It can be used in robotics for controlling motors, sensors, etc.
 It can be used as a downloading machine replacing desktop computers. It consumes very low
power and also can be accessed remotely.
 It can be used as a media centre at home. Any television can be converted to a smart TV with
internet capabilities with the Pi.
 It can be used for designing prototypes of DIY projects and certain embedded devices. It
becomes very cheap option for testing and evaluation purpose.
 Can be used in creating and handling small servers.
 It can be used for making digital photo frames, tablets etc at home
Examples of projects using Raspberry Pi
1) Home Automation
With a Raspberry Pi, switches, web server, enthusiasts have created home automation
systems that can control fans and lights of a home from the Pi or even a smartphone.

Figure 11: An example of a home automation system using RPi.
2) Arcade gaming machine
Since the games of the 80’s and 90’s are forgotten today, people created retro style arcade
gaming machines using simple switches, a screen and the RPi.
Figure 12: Arcade gaming machines using RPi
3) Robot
While robotics has a great fan base, creating a star wars robot from RPi deserves a mention
here!

Figure13: Raspberry Pi inside therobot
Figure14: The robotwith the Pi. The R2D2.

4) Landline
Why pay for your landline when you can use your internet and your old landline phone with
the Pi!
Figure 15: Landline using RPi and Google Voice
5) Diwali lights / Decoration lights controller
The RPi can be used to make a remote control for all the decoration lights in the house!
Figure 16: RPi based decoration lights controller

Comparison of Raspberry with the competitors
The chief competitors of the Raspberry Pi are the Arduino and the Beagleboard. Both are single
board computers and have applications similar to the Raspberry Pi. A brief comparison of the three
of them is shown below:
Figure 17: Comparison of RPi with chief competitors

ADVANTAGES

It is important for customers and business owners that want to get the Raspberry Pi to consider
whether it fits with their business strategy and are willing to go through the process of putting it
together and tailoring the product to their own needs. The benefits that this products offers beside the
low price point are:
 This microcomputer is useful for small or home based businesses that run on a smaller budget
than bigger companies for you are not required to purchase any special licenses from the
Raspberry Pi Foundation to use their product or if you invent new technology that embeds the
product. Small business owners can use it to automate any small task, such as using the Pi to
run a website ( as long as it does not have a lot of traffic), or use it as a small database and
media server... pretty much anything that doesn't require the Windows operating system or
other systems that does not support Linux and lots of traffic). Businesses can also save money
on buying cooling systems that are required to cool servers.
 The product does not require the user to have extensive programming experience since it is
aimed for the younger generation to learn about programming. Python, the programming
language that the Pi uses, is less complex than other languages available. For example, it has
better code readability and allows the user to type concepts using fewer amount of lines.
Python also has an automatic memory management function.
 The product also gives you a lot of room to experiment and turn it into something else that is
entirely different. The SD cards on the board can be easily switched, which allows you to
change the functions of the device without spending a lot of time re-installing the software.
 The Raspberry Pi is perfect for adaptive technology: it is able to display images or play
videos at 1080p high definition resolution to building systems such as digital jukeboxes
or prototyping embedded systems. This product makes it possible to build complex and
effective products at a cheaper price.
 The product is energy efficient and provides a greener ethical alternative to small businesses.
This small credit card sized product makes it easy to recycle and does not release as much
carbon dioxide emissions into the environment, unlike big servers that require lots of energy
and extensive cooling systems.

DISADVANTAGES

 It does not replace your computer, since the Ethernet is only a 10/100 and the processor is not
as fast, it is time consuming to download and install software and is unable to do any
complex multitasking.
 Not compatible with other operating systems such as Windows (There are currently 1.3
billion Windows users around the world.)
 To use the Raspberry Pi,it will take more than just 35 dollars to get it to do what you need
through buying extra accessories such as the SD card, USB power supply, keyboard..etc and
if you take into account the acquisition cost of the product. This is only fit for those who want
a gadget that they can tailor to their own needs and tastes, not for those who just wants to get
a job done fast. Business owners need to consider if the extra hassle is worth it.
 This product will not be useful for bigger businesses that already have big servers, which
would already do everything that the Raspberry Pi does, so it would not be worth it to take
the time to get someone to put it together.

FUTURE SCOPE

1. For now, this paper proposes replacing laptops with the new storage device for a
department. This can be extended over a large scale too, say for all the departments of
the college and then also over many institutes all over the country. This product indeed has
tremendous potential of replacing laptops, especially for the particular application of
storage and projecting.
2. Another future scope is powering the Raspberry Pi using a battery. For now, the Raspberry Pi
needs to be connected to the power supply via the USB power port. But in case the power
goes off, it would turn off the Pi abruptly. So, it would be better if the Raspberry Pi is
connected to a backup battery power supply.
3. This application note assumes the user has already created a working Linux image on an SD
card and the Raspberry Pi is already functional.This application note will show how to connect
the RPI-Hub-Module to the Raspberry Pi and install FTDI drivers to control the module. The
application note will then explain how the module may be used to read values from an external
ADC device over the SPI interface.

CONCLUSION

Raspberry Pi is an innovative product. The sheer number of users and fan base support the fact that
the device can see a great future ahead. The device can surely help anyone who really wants to lean
electronics and computers.
Increasing the processing power can surely help the product in the future. Also supplying a case and
a proper instruction manual will improve the product. Also currently Windows operating systems are
not compatible because of the ARM processor. If the processor is improved or any workaround is
found to run Windows directly on the Raspberry Pi, then it can be a great step for the Pi.
The Raspberry Pi is an amazing piece of hardware because of the combination of the features of a
traditional computer and an embedded device. Supporting computer operating systems like Linux
and providing simple input/output lines i.e. the GPIO makes it perfect for controlling almost
anything. Programming the GPIO is much easy and intuitive then an traditional FPGA or
microprocessor.
Finally it can be said that Raspberry Pi can be effectively used if its processing power is kept in
mind. It can work as a personal computer but cannot replace it.

APPENDIXES

FIGURE NUMBER FIGURE NAME PAGE NUMBER
1 Osbome 1 computer 5
2 Toshiba T1100 5
3 A complete commodore 64
system
7
4 One of the earliest prototype
of the pi
8
5 Block diagram of Raspberry
pi
11
6 GIPO Connector on RPi 13
7 RCA Video Connector 14
8 Status LEDs 15
Table 1 Specifications 16
9 Gertboard (left) & Raspberry
Pi(Right)
19
10 Boot process of Raspberry Pi 24
Table 2 List of supported Operating
Systems
27
11 An example of a home
automation system using RPi
30
12 Arcade gaming machines
using RPi
30
13 Raspberry Pi inside the robot 31
14 The robot with the Pi. The
R2D2.
31
15 Landline using RPi and
Google Voice
32
16 RPi based decoration lights
controller
32
17 Comparison of RPi with chief
competitors
33

BIBLIOGRAPHY

[1] History of embedded devices, http://www.discussionsworld.com/forum_posts.asp?TID=42603
[2] About Raspberry Pi, http://www.raspberrypi.org/about/
[3] Early prototype of Raspberry Pi, http://www.raspberrypi.org/raspberry-pi-2006-edition/
[4] Raspberry Pi Hardware information, http://elinux.org/RPi_Hardware
[5] How SoC works, http://www.androidauthority.com/how-it-works-systems-on-a-chip-soc-93587/
[6] Boot process, http://thekandyancode.wordpress.com/2013/09/21/how-the-raspberry-pi-boots-up/
[7] NOOBS, http://www.raspberrypi.org/introducing-noobs/
[8] List of available OS, http://elinux.org/RPi_Distributions
[9] Home automation project, http://www.instructables.com/id/Raspberry-Pi-GPIO-home-
automation
[10] Arcade gaming machine project, http://www.cnet.com/how-to/25-fun-things-to-do-with-a-
raspberry-pi/
[11] Robot project, http://www.wired.com/2013/01/raspberry-pi-r2d2/
[12] Landline telephone project, https://www.twilio.com/blog/2013/03/build-a-twilio-hard-phone-
with-sip-from-twilio-raspberry-pi-asterisk-freepbx-and-the-obihai-obi100.html
[13] Decoration lights project, http://www.element14.com/community/community/raspberry-
pi/raspberrypi_projects/blog/2013/12/12/raspberry-pi-enabled-christmas-lights
[14] Advantages-Disadvantages,
https://sites.google.com/site/mis237groupprojectraspberrypi/home/what-is-raspberry-pi/pros-and-
cons-of-the-raspberry-pi

Raspberry pi on seminar documentation

More Related Content

What's hot (20)

Viewers also liked (9)

Similar to Raspberry pi on seminar documentation (20)

More from Georgekutty Francis (12)

Recently uploaded (20)

Raspberry pi on seminar documentation