Satellite Subsystems
- 2. CONTENTS: Attitude & Orbit control system TTC&M system Power system Communication subsystems Satellite Antennas Space Qualification Equipment Reliability
- 3. Telemetry, Tracking, Command & Monitoring(TTC&M)
- 5. Telemetry & Monitoring System: It collects data from many sensors within satellite & send these data to the controlling earth station. Several hundred of sensors are located on satellite to monitor pressure in the fuel tanks, voltage & current in power conditioning unit, current drawn by each subsystem , & critical voltages & current in communications electronics.
- 6. Temperature of many subsystem must be kept within predetermined limits, so many temp. sensors are fitted. The sensor data, the status of each subsystem are reported back to the earth by telemetry system. Telemetry data are digitized and transmitted as phase shift keying(PSK) of low- power telemetry carrier using time division techniques.
- 7. At controlling earth station a computer can be used to monitor, store, and decode telemetry data so that status of any system or sensors on the satellite can be determined immediately. Alarms can also be sounded if any vital parameter goes outside allowable limits.
- 8. Tracking: A no. of techniques can be used to determine current orbit of satellite. Velocity & acceleration sensors on satellite can be used to establish the change in orbit from last known position, by integration of data. The earth station controlling satellite can observe the Doppler shift of telemetry carrier to determine rate at which range is changing.
- 9. Active determination of range can be achieved by transmitting a pulse, or sequence of pulses, to the satellite and observing the time delay before pulse is received again.
- 10. Command: The command system is used to make changes in attitude and corrections to the orbit and to control communication system. During launch, it is used to control firing of AKM & to spin up spinner or extend solar sails & antennas of 3- axis stabilized satellite.
- 11. The command structure must posses safeguards against unauthorized attempts to make changes to satellite’s operation. Encryption of commands & responses is used to provide security in command system. After monitoring all the data, commands are generated at the control terminal of computer.
- 12. The command word is sent in a TDM frame to the satellite. After checking for validity in satellite, command word is sent back to the control station via telemetry link where it is checked again in the computer. If it found correctly, an execute instruction will sent to satellite. The entire process may take 5 0r 10s, but minimizes the risk of erroneous commands causing satellite malfunction.
- 13. Power System: All communication satellites obtain their electrical power from solar cells, which converts incident sunlight into electrical energy. Some deep space planetary research satellites have used thermonuclear generators. Communication satellite have not used nuclear generators.
- 14. Sun is a powerful source of energy. At geostationary altitude, the radiation falling on a satellite has an intensity of 1.39kW/𝑚2. Solar cells do not convert all incident energy into electrical power; their efficiency is typically 20 to 25% at beginning of life(BOL) but falls with the time because of aging of the cells. Since sufficient power must be available at the end of life(EOL) of satellite to supply all the systems on board, about 15% extra area of solar cells is usually provided as an allowance for aging.
- 15. A spin stabilized satellite usually has a cylindrical body covered in solar cells. Because solar cells are on cylindrical surface, half of the cells are not illuminated at all, which results little electrical power being generated. The cells that are not illuminated by sunlight face cold space, which cause them to cool down. More recently, large communication satellites for direct broadcast operation generate up to 6kW from solar power.
- 19. A three- axis stabilized satellite can make better use of its solar cell area, since the cells can be arranged on flat panels that can be rotated to maintain normal incidence of the sunlight. A primary advantage is that by unfurling a folded solar array when the satellite reaches geostationary orbit, power in excess of 10kW can be generated with large array. To obtain 10kW from a spinner requires a very large body as compared to three-axis stabilized body.
- 20. Attitude & Orbit Control System(AOCS): This subsystem consists of rocket motors that are used to move the satellite back to the correct orbit when external forces cause it to drift off station Gas jets are used to control the attitude of the satellite. The attitude and orbit of a satellite must be controlled so that the satellite’s antennas point toward the earth and so that user knows where in the sky to look for the satellite.
- 21. Attitude control system: There are two ways to make a satellite stable in orbit. The body of the satellite can be rotated at rate between 30 & 100 rpm, that provides stability of the spin axis & keeps it pointing in the same direction, such satellites are known as spinners. Alternatively, the satellite can be stabilized by the one or more momentum wheels, called as three- axis stabilized satellite.
- 22. The momentum wheel is usually a solid metal disk driven by an electric motor. There must be one momentum wheel for each of the three axes of the satellite and rotated to provide a rotational force about any of the three axes. There are two types of rocket motors used on satellite 1. Bipropellant thrusters 2. arc jets or ion thrusters
- 23. In three-axis stabilized satellite, one pair of gas jets is needed for each axis to provide rotation in both direction. When motion required along particular axis , the appropriate gas jets is operated for a specific period of time.
- 24. The satellite attitude is defined in terms of three axis - ROLL , PITCH, YAW Roll axis is towards the velocity vector of the satellite as the satellite moves in orbit. Yaw axis is towards the earth center. Pitch axis is mutually perpendicular to both these two axis. They are called earth oriented co-ordinate axes.
- 26. Any perturbing force about a particular axis can cause a slight rotation about that axis. The zero error attitude is defined when the satellite antenna radiation beam point to the required direction. With this zero error attitude, the solar panels also will be able to track the sun properly.
- 27. Error in attitude is determined by attitude error detection sensors(Infra red earth sensors) attached to the satellite. Any object which is above absolute zero degree Kelvin radiates energy & earth at 300 degree kelvin radiates infrared energy more compared to other wavelength bands.
- 29. By processing the pulse width generated by sensors, it is possible to measure the attitude error about Roll & Pitch axes.
- 30. Orbit control: The gravitation forces of moon & the sun cause inclination of orbital plane. There are many other smaller forces that act on satellite causing the orbit to change. For the orbit to be truly geostationary, it must lie in equatorial plane, be circular and have correct altitude.
- 32. The various forces acting on the satellite will steadily pull it out of the correct orbit; it is the function of the orbit control system to return it to the correct orbit. Gas jets that can impart velocity changes along three reference axes of satellite are used. Correcting the inclination of a satellite orbit requires more fuel to expended than for any other orbital correction. This places a weight penalty on those satellites that must maintain accurate station keeping & reduces communication payload they can carry.
- 33. Communication Subsystems Transponders- A transponder consists of BPF to select the particular channel’s band of frequency, a downconverter & an output amplifier.
- 34. Fig. shows a typical single conversion bent pipe transponder used on many satellites for 6/4 GHz band. The local oscillator is at 2225 MHz to provide the appropriate shift in frequency from 6 GHz to 4 GHz. Band pass filter after the mixer removes unwanted frequencies. The output power amplifier is usually a solid state power amplifier(SSPA)unless a very high output power is required.
- 35. Redundancy is provided for high-power amplifiers in each transponder by including a spare TWTA(travelling Wave tube amplifier) or solid-state amplifier(SSPA) that can be switched if primary power amplifiers fail. The lifetime of high power amplifier’s is limited and they represent least reliable component in most transponders. Providing a spare HPA in each transponder increases the probability that the satellite will reach the end of its working life with all its transponders working.
- 37. Transponders for use in the 14/11-GHz bands normally employ a double frequency conversion scheme Incoming 14-GHz carrier is translated to an IF around 1GHz. The amplification & filtering are performed at 1 GHz & a relatively high-level carrier is translated back to 11 GHz for amplification by HPA.
- 38. Satellite Antennas: Wire Antennas: Monopole & Dipole Horn Antennas Reflector Antennas Array Antennas
- 39. Wire Antennas: These are used primarily at VHF & UHF to provide communications for the TTC&M systems. They are positioned with great care on the body of the satellite in an attempt to provide omnidirectional coverage. An antenna pattern is a plot of the field strength in far field on antenna. It is usually measured in decibels(dB).
- 41. Horn Antennas: These are used at microwave frequencies when relatively wide beams are required, as for global coverage. A horn is a flared section of waveguide that provides an aperture several wavelengths wide and a good match between the waveguide impedance and free space. Horns are also used as feeds for reflectors
- 43. Reflector Antennas: The most often used antenna for satellite systems, particularly for those operating above 10 GHz, is the parabolic reflector antenna. These are usually illuminated by one or more horns and provide a lager aperture compared to horn antenna. Parabolic reflectors offer a much higher gain than that achievable by the horn antenna alone.
- 45. Array Antennas: Array antennas are also used on satellites to create multiple beams from a single aperture. Multiple beams are formed by combining the radiation from several small elements made up of dipoles, horns etc. Iridium and Globalstar used these kind of antennas to generate up to 16 beams from a single aperture for their LEO mobile telephone systems.
- 46. Equipment Reliability & Space qualification: Once satellite is in geostationary orbit, there is little possibility of repairing components that fail or adding more fuel for station keeping. The component that make up the satellite must therefore have very high reliability. Two approaches are used: Space qualification of every part of the satellite to ensure that it has a long life expectancy in orbit & redundancy of most critical components to provide continued operation when one component fails.
- 47. Space Qualification: Outer space, at geostationary orbit distances, is a harsh environment. The sun irradiates the satellite with 1.4 kW of heat and light on each square meter of exposed surface. When surfaces are in shadow, surface temperature will fall toward absolute zero. Electronic equipment can’t operate at such extremes of temperature & heated or cooled so that it’s temp. stays within the range 0˚ to 75 ˚C. This requires a thermal control system.
- 48. The first stage in ensuring high reliability in a satellite is by selection and screening of every component used. Past operational & test experience of components indicates which components can be expected to have good reliability. Each component is tested individually to ensure that it meets its specification. This process is known as quality control or quality assurance & is vital in building any equipment that is to be reliable. Once individual components and subsystems have been space qualified, the complete satellite must be tested as a system to ensure that its many systems are reliable. When a satellite is designed, three prototype models are often build and tested.
- 49. Mechanical model- It contains all the structural & mechanical parts that will be included in the satellite & is tested to ensure that all moving parts operate correctly in vacuum, over a wide temperature range. It also subjected to vibration & shock testing. Thermal model- It contains all electronics packages and other components that must be maintained at the correct temperature. Electrical model- contains all the electronic parts of the satellite and is tested for correct electrical performance under total vacuum and a wide range of temperatures.
- 50. Testing carried out on models is designed to overstress the system and induce failure in any weak components. Temperature cycling will be carried out to 10% beyond expected extremes; structural loads 50% above those expected may be applied. Electrical equipment will be subjected to excess voltage and current drain to test for food electronic and thermal reliability.
- 51. Reliability: We need to be able to calculate reliability for two reasons: We want to know what the probability is that subsystem will still be working after a given time period, & we need to provide redundant components or subsystems where probability of failure is too great to be accepted. Reliability is a mathematical technique which gives an idea about the probability of failure.
- 52. The reliability of a component can be expressed in terms of probability of failure after time t. For most electronic equipment, probability of failure is higher at beginning of life- the burn – in period. As the component ages, failure becomes more likely. Mathematically reliability of device or sub-system is defined as,
- 53. The other improvement parameter in reliability study is the meantime before failure (MTBF) and is given by Where ti = time after which ith device fails. MTBF is related to average failure by
- 54. The failure rate ⅄ is often given as average failure rate per 109 hours. In terms of reliability of subsystem or device it is given by
- 55. Redundancy: By using redundant components, reliability of subsystem can be increased. The redundant device can incorporate with the existing operating devices/ components either in series or in parallel or may be mixed.