Synopsis for Public Garden automation with solar tracker by Punith urs
- 1. PUBLIC GARDEN AUTOMATION WITH SOLAR TRACKER PROJECT SYNOPSIS IN FULFILMENT OF THE REQUIREMENTS FOR THE DEGREE OF Bachelor of Engineering In ELECTRICAL ENGINEERING By PUNITH K.R. (4AI11EE029) Department of Electrical Engineering Adichunchanagiri Institute of Technology Chikmagalur-Karnataka
- 2. PUBLIC GARDEN AUTOMATION WITH SOLAR TRACKER ABSTRACT The most important problems faced are the misusage of electricity and its wastage. Sometimes due to carelessness of the authorities and the workers lamps are left ON which results in wastage of electricity, negligence in switching the water supply depending upon the moisture content of soil, Garden opening and closing at specific time etc. Here we are using solar energy to drive the system by solar tracker. Our project helps to overcome all these problems. Water wastage is another problem which needs to be dealt with. Our project helps to overcome all these problems. INTRODUCTION As we all know that there is a need to reduce the wastage of electricity as well as water in daily usage of our life. So one of the common area of our day today life, where we can implement it, so that to save the energy is the Public Gardens. So our project is all about the efficient utilisation of renewable energy resourses. Firstly the Microcontroller around 4.00pm switches on the water supply once to water the entire garden few hours before opening of the garden for public. Next the gate is opened by running the motor which is driven by a motor driver operated by the Microcontroller. Depending upon the output of the LDR and the lights remain functional till the garden remains open for visitors. The garden remains open for about three hours and so around 8.50 pm a buzzer is sounded to indicate closure of the garden and alert the visitors. The gate is then closed at 9.00pm and one of the two lamps is switched off. One lamp is kept on throughout the night. In the morning the remaining lamp is switched off depending upon the signal sent by the LDR, light dependent resistor to the Microcontroller. These are the step involved in the operation of the circuit and the public garden automation.
- 3. Microcontroller is used to supervise the actions of all other devices and to control the entire set of operations. We are using solar tracker to drive lamps and motor. BLOCK DIAGRAM Figure 1: Public GardenAutomationwithSolar Tracker
- 4. Figure 2:LOAD SIDE HARDWARE REQUIREMENT 8051/PIC Micro Controller Solar Panel (for prototype Around 5W) Relay and Driver Circuit LDR Stepper / Geared motor ( 12v) Battery (6V / 12V) SOFTWARE REQUIREMENT Kiel Multisim Power supply: It is the main part of the circuit; the circuit needs the12V DC supply. But in our home 230 AC supply is available. So it has converted it to 12V DC and 5V DC by Rectifier circuit by regulator IC 7812 and 7805 respectively. LOAD LAMPS PUMP & MOTOR FOR GATE OPENING
- 5. Micro Controllers: It is the Heart of the Circuit. In this circuit we are going to use the 8051/PIC MCU. Microcontrollers are used in automatically controlled products and devices, such as automobile engine control systems, implantable medical devices, remote controls, office machines, appliances, power tools, toys and other embedded systems. Here we are controlling the rotation of solar panel by stepper or geared motor. Geared DC motors can be defined as an extension of DC motor which already had its Insight details demystified . A geared DC Motor has a gear assembly attached to the motor. The speed of motor is counted in terms of rotations of the shaft per minute and is termed as RPM .The gear assembly helps in increasing the torque and reducing the speed. Using the correct combination of gears in a gear motor, its speed can be reduced to any desirable figure. This concept where gears reduce the speed of the vehicle but increase its torque is known as gear reduction. This Insight will explore all the minor and major details that make the gear head and hence the working of geared DC motor. LDRs (Light Dependent Resistors): They are very useful especially in light/dark sensor circuits. Normally the resistance of an LDR is very high, sometimes as high as 1000 000 ohms, but when they are illuminated with light resistance drops dramatically. A solar panel (Also solar module, photovoltaic module or photovoltaic panel): is a packaged, connected assembly of photovoltaic cells. The solar panel can be used as a component of a larger photovoltaic system to generate and supply electricity in commercial and residential applications. Driver IC: It is a high voltage and high current Darlington array IC. It contains open collector Darlington pairs with common emitters. A Darlington pair is an arrangement of two bipolar transistors. Recommended for high-side switching applications that benefit from separate logic and load grounds, these devices encompass load supply voltages to 50 V and output currents to -500 mA. These 8-channel source drivers are useful for interfacing between low-level logic and high-current loads.
- 6. Relay: It is an electromagnetic device used to separate two circuits electrically and connect them magnetically. They are often used to interface an electronic circuit, which works at a low voltage to an electrical circuit which works at a high voltage. Relays are available in different configuration of operating voltages like 6V, 9V, 12V, 24V etc. Inverter: It converts the DC supply whatever we are getting from the battery into AC. An electric battery is a device consisting of one or more electrochemical cells that convert stored chemical energy into electrical energy. Each cell contains a positive terminal, or cathode, and a negative terminal, or anode. Electrolytes allow ions to move between the electrodes and terminals, which allows current to flow out of the battery to perform work. The application program for the microcontroller will be written in embedded ‘Embedded C’ /Assembly and will be stored in the flash memory of the microcontroller. FEATURES Depending upon the time schedule watering, garden opening, closing and alerting system is done. Based on light intensity & time garden lamps are going to switch. Solar panel is going to track the light intensity based on the LDR. Before closing the garden gate system are going to alerts the people by activating alarm. LCD is going to display the present status of the system.
- 7. FUTURE SCOPE This project mainly aims at the automation of the public garden to avoid wastage of resources. This can be expanded in the sense of security. Using metal detectors and CCTV cameras security of the garden can be enhanced. By using GSM technology further control of water supply and lights using mobile can be achieved. APPLICATIONS This small scale project can be implemented in any public garden with minimum cost and resources. This helps in proper utilization of the available resources and helps in avoiding wastage of electricity and water. Go green ,,!